What comes in the box:

Transcription

1 INSTRUCTIONS

2

3 Congratulations on the purchase of your Rigid Industries Capture. Welcome to the Rigid Nation! What comes in the box: 1 x Capture Light 1 x Harness 2 x Custom Carling Technologies Switches 2 x Amber 4 Light Covers 2 x Mount Bushings 2 x Mount Brackets 4 x 1/4 Nylon Locknuts 4 x 1/4 Flat Washers 4 x 1/4 Hex Head Screws

4

5 Recommended installation instructions: Rigid Industries always recommends installation from an industry professional. Be sure to read warranty information Disconnect the negative battery cable from the battery before continuing. Install the mounting brackets onto the Capture as shown in the above diagram. Secure the hardware to a snug position so that it can be adjusted once mounted to your vehicle. Mount the Capture to vehicle in desired location with hardware of your choice for your specific application.

6 Route the wiring harness from the Capture to your vehicle battery and desired switch locations. Secure harness in place with zip ties. Be sure to avoid sharp edges, abrasive surfaces, and heat sources that might cause failures over time. Attach the Capture s weather-sealed Deutsch connector to the wiring harness. Attach the red terminal eyelet on the wiring harness to the battery positive or any 12V DC source. Attach the black terminal eyelet to the battery negative or any suitable ground. Attach the wiring harness to the switches per the diagrams on the following pages.

7 8. 9. Reconnect the negative battery cable to the battery. Adjust light position then finish tightening the hardware. We recommend parking your vehicle on a flat surface facing a wall. This will help adjust and level your light for optimal video recording experience. 10. Install a GoPro Hero 3+ or 4 into the Capture housing and seal the door shut with the clip. When the camera power switch is on, your GoPro will be charging and its battery won t die, even when you re recording for hours at a time. 11. Go light up the night and film your adventures!

8 Notes When installing Rigid Industries lights on a 24V DC system be sure to use a 24V relay. When installing multiple lights be sure to have adequate fusing. Using mounting hardware or wiring other than what is provided by Rigid Industries can result in damage and possible void of warranty.

9 FRONT BACK LIGHT SWITCH Black White Red Red with Heat Shrink CAMERA SWITCH Black Red Red with Heat Shrink

10 WARRANTY Rigid Industries warrants that this product will be free from defects in material and workmanship. If you believe your Rigid Industries product is defective, it must be returned to Rigid Industries for inspection by our warranty claims department. If, after inspection, Rigid Industries verifies that the defect was not caused by negligence, abuse, unauthorized repair or disassembly, Rigid Industries will determine whether the product will be repaired or replaced in accordance with Rigid Industries Limited Lifetime Warranty*. Without registering your purchase or having your original proof of purchase available, the Rigid Industries Limited Lifetime Warranty could be voided. No Rigid Industries Limited Lifetime Warranty is available for the Rigid Industries Capture series of lights until a warranty registration is received from the end user and approved by Rigid. To begin your warranty claim, you must have a Return Merchandise Authorization (RMA) number. To get your RMA number, please contact our warranty department by phone or by filling out the Return Merchandise Authorization Form found on our website www. RigidIndustries.com/about/warranty.

11 WARRANTY Continued All of the following will immediately void all warranties: Customer negligence The customer has modified the light and/or is not using it for the recommend application. Customer abuse Damage to the light beyond normal wear and tear. Repair work done by unauthorized personnel without Rigid Industries approval. If the light has been opened or any screws have been removed. All warranties are non-transferable. Warranty terms and policies are subject to change without notice. *For all information regarding the Rigid Industries Limited Lifetime Warranty please call ext. 1008, or visit our warranty page online at rigidindustries.com/about/warranty. Rigid Industries and Capture are registered and/or common law marks owned by JST Performance, LLC d/b/a Rigid Industries.

12 Check out for more information including: videos from other Rigid Nation members, accessories, installation dimensions, recommendations, and more! PKG-IS-136-B