2001 Chevrolet Corvette V8-5.7L VIN G
|
|
|
- Jonathan Singleton
- 5 years ago
- Views:
Transcription
1 1 of 14 2/21/ :34 AM 2001 Chevrolet Corvette V8-5.7L VIN G Vehicle» Engine, Cooling and Exhaust» Engine» Oil Pan» Service and Repair Oil Pan Replacement Removal Procedure Remove the front suspension crossmember. Remove the oil pan drain plug and allow the oil to drain. Re-install the engine oil drain plug until snug. Important: It is not necessary to remove the oil pan (lower) in order to remove the oil pan. 4. If oil pan and/or gasket removal or replacement is NOT required proceed to step 10. If the oil pan (lower) gasket replacement is required proceed to the next step.
2 2 of 14 2/21/ :34 AM If replacement of the oil pan (lower) gasket is needed, perform the following: Remove the oil pan (lower) bolt (1-15). 7. Separate the oil pan (lower) (3) from the oil pan (1).
3 3 of 14 2/21/ :34 AM Remove the oil pan (lower) gasket (2). Clean the oil pan (lower) gasket surface. For the oil pan (lower) installation, refer to step 11 in the installation procedure Remove the starter motor. Remove the left transmission cover bolt and cover Remove the engine oil filter and allow the oil to drain. Re-install the engine oil filter until snug.
4 4 of 14 2/21/ :34 AM 14. Remove the automatic transmission fluid cooler line clamp bolt at the right transmission cover, if equipped. 15. Remove the automatic transmission fluid cooler line clamp bolt at the oil pan, if equipped.
5 5 of 14 2/21/ :34 AM 16. Remove the right transmission cover bolt and cover 17. Remove the bottom 2 flywheel housing-to-oil pan bolts.
6 6 of 14 2/21/ :34 AM 18. Disconnect the engine oil level sensor electrical connector (2). 19. Disconnect the engine oil temperature sensor (3) electrical connector.
7 7 of 14 2/21/ :34 AM 20. Remove the oil pan bolts. Important: The original oil pan gasket is retained and aligned to the oil pan by rivets. When installing a new gasket, it is not necessary to install new oil pan gasket rivets. DO NOT reuse the oil pan gasket. When installing the oil pan, install a NEW oil pan gasket. Removal of the oil pan (lower) will not provide access to the crankshaft oil deflector, crankshaft, or other internal engine components Lower the oil pan, rotate the pan until it can be removed from around the oil pump screen. Remove the engine oil filter. Clean and inspect the engine oil pan. Installation Procedure
8 8 of 14 2/21/ :34 AM Important: All gasket surfaces should be free of oil or other foreign material during assembly. The alignment of the structural oil pan is critical. The rear bolt hole locations of the oil pan provide mounting points for the flywheel housing cover. To ensure the rigidity of the powertrain and correct transmission alignment, it is important that the rear of the block and the rear of the oil pan are flush or even. The rear of the oil pan must NEVER protrude beyond the engine block. Do NOT reuse the oil pan gasket. It is not necessary to rivet the NEW gasket to the oil pan. 1. Apply a 5 mm (0.20 inch) bead of sealant GM P/N or equivalent 20 mm (0.80 inch) long to the engine block. Apply the sealant directly onto the tabs of the front cover gasket that protrude into the oil pan surface. 2. Apply a 5 mm (0.20 inch) bead of sealant GM P/N or equivalent 20 mm (0.80 inch) long to the engine block. Apply the sealant directly onto the tabs of the rear cover gasket that protrude into the oil pan surface.
9 9 of 14 2/21/ :34 AM Important: Be sure to align the oil gallery passages in the oil pan and engine block properly with the oil pan gasket. 3. Pre-assemble the oil pan gasket to the pan Install the gasket onto the oil pan Install the oil pan bolts to the pan and through the gasket Install the oil pan, gasket and bolts to the engine block Tighten the oil pan bolts until snug. Do not overtighten. 4. Install the 2 bottom flywheel housing bolts to position the oil pan correctly.
10 10 of 14 2/21/ :34 AM Notice: Refer to Fastener Notice in Service Precautions. 5. Tighten the 2 bottom flywheel housing bolts until snug. Do not overtighten Tighten the oil pan bolt and oil pan-to-front cover bolts to 25 Nm (18 ft. lbs.) Tighten the oil pan-to-rear cover bolts to 12 Nm (106 inch lbs.) Tighten the flywheel housing bolts to 50 Nm (37 ft. lbs.). 6. Connect the engine oil temperature sensor (3) electrical connector.
11 11 of 14 2/21/ :34 AM 7. Connect the engine oil level sensor electrical connector (2). 8. Install the right transmission cover and bolt. Tighten the right transmission cover bolt to 12 Nm (106 inch lbs.). 9. Install the automatic transmission fluid cooler line clamp bolt-at-the oil pan, if equipped. Tighten the automatic transmission fluid cooler line clamp bolt-at-the oil pan to 12 Nm (106 inch lbs.).
12 12 of 14 2/21/ :34 AM 10. Install the automatic transmission fluid cooler line clamp bolt-at-right transmission cover, if equipped. Tighten the automatic transmission fluid cooler line bolt-at-right transmission cover to 2.5 Nm (22 inch lbs.). 11. Install the left transmission cover and bolt. Tighten the left transmission cover bolt to 12 Nm (106 inch lbs.). 12. Install the starter motor.
13 13 of 14 2/21/ :34 AM Install the oil pan (lower) (3) and gasket (2) to the oil pan (1). Install the oil pan bolts (4). 15. Tighten the oil pan (lower) bolts (1-15) in a crossing pattern, alternating from side-to-side.
14 14 of 14 2/21/ :34 AM Tighten the oil pan (lower) bolts to 12 Nm (106 inch lbs.). 16. Install a NEW engine oil filter. Tighten the engine oil filter to 30 Nm (22 ft. lbs.). 17. Install the oil pan drain plug. Tighten the oil pan drain plug to 25 Nm (18 ft. lbs.) Install the front suspension crossmember to the vehicle. Fill the crankcase with the proper quantity and grade of engine oil. Check the transmission fluid, add if necessary. Run the engine and check for leaks.
Oil Pan Replacement Buick Regal
2000 Buick Regal Oil Pan Replacement Removal Procedure Tools Required J 28467-90A Engine Support Adapters J 28467-B Universal Engine Support Fixture J 36462-A Engine Support Adapter Leg Set 1. Disconnect
2005 Chevrolet Equinox Equinox VIN L Service Manual Engine Engine Mechanical - 3.4L Repair Instructions - On Vehicle Document ID:
xtooltipelement Service Information 2005 Chevrolet Equinox Equinox VIN L Service Manual Engine Engine Mechanical - 3.4L Repair Instructions - On Vehicle Document ID: 1383623 Engine Front Cover Replacement
ROAD RACE BAFFLE for LT OIL PANS P/N
ROAD RACE BAFFLE for LT OIL PANS P/N 302-30 Instruction Sheet 199R11191 NOTE: This instruction sheet is intended for installation after a Holley LT oil pan (302-20) has previously been installed. If installing
Sikky Oil Pan Install Guide
Sikky Oil Pan Install Guide **If you have a double chain timing belt or after market oil pump setup then further modifications may need to be made in order for the pan to fit.** Remove starter Remove plastic
Engine Oil Cooler Hose/Pipe Replacement (4WD)
Page 1 of 9 1998 Chevrolet Blazer - 4WD Blazer, Bravada, Jimmy, S10 Pickup, Sonoma (VIN S/T) Service Manual Engine Engine Mechanical - 4.3L Repair Instructions Document ID: 179331 Engine Oil Cooler Hose/Pipe
Piston Cooling Nozzle, Replacement
Volvo Trucks North America Greensboro, NC USA This Service Bulletin replaces Service Bulletin 221-49, Piston Cooling, dated (1.2007), publication no. PV776-20177472. DService Bulletin Trucks Date Group
1 of 8 12/12/2012 6:08 PM 1999 Chevrolet Express - 2WD Express, Savana VIN G Service Manual Engine Engine Mechanical - 6.5L Repair Instructions Engine Replacement Removal Procedure Tools Required J 36857
OIL PAN with DRAG RACE BAFFLING P/N
OIL PAN with DRAG RACE BAFFLING P/N 302-22 Instruction Sheet 199R11161 CONGRATULATIONS on your purchase of a Holley LT Retro-fit Oil Pan! We feel that you have purchased the finest performance oil pan
Page 1 of 5 2004 Pontiac GRAND PRIX Submodel: Engine Type: V6 Liters: 3.8 Fuel Delivery: FI Fuel: GAS Oil Pan Replacement Removal Procedure Disconnect the negative battery cable. Refer to Battery Negative
This information covers procedures for replacing the sealant for the crankshaft cover on the Volvo D16F engine.
Volvo Trucks North America Greensboro, NC USA DService Bulletin Trucks Date Group No. Page 1.2008 216 50 1(17) Sealant Crankshaft Cover, Replacement D16F Sealant Crankshaft Cover, Replacement W2005773
ALLDATA Online Cadillac DeVille V8-4.6L VIN Y - Lower Crankcase Installation. Lower Crankcase Installation
Page 1 of 7 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1998 Cadillac DeVille V8-4.6L VIN Y Conversion Calculator Vehicle
Lower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
2001 Chevrolet CORVETTE
riveline Support Assembly Replacement (Automatic Transmission) 1 of 21 10/24/2012 8:58 PM 2001 Chevrolet CORVETTE Submodel: Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Driveline Support Assembly
Page 1 of 6 Section 03-01B: Engine, 7.5L MFI Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 05/17/2000 Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Damper Remover
1994 Ford Mustang - Engine Mechanical > Engine Mechanical Components > Timing Chain Cove...
Page 1 of 6 1994 Ford Mustang : Engine Mechanical > Engine Mechanical Components > Timing Chain Cover & Seal > Removal & Installation > 5.0L Engine 5.0L Engine 1. Disconnect the negative battery cable
3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter
1 of 16 Transmission Replacement Tools Required ^ J 41623-B Cooler Quick Connect Tool ^ J 41160 Transmission Jack Adapter Removal Procedure 1. Remove the upper filler panel. 2. Remove the upper and lower
GM 4T65E Installation Tips
GM 4T65E Installation Tips WARNING: DO NOT operate vehicle without installing a new transmission oil cooler. We recommend installing a Hayden 1403 or 1404. Bypass the radiator and install the new cooler.
2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender
IN-VEHICLE REPAIR. Engine Front Cover
303-01A-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01A-1 Special Tool(s) SAE 5W-20 Premium WSS-M2C930-A Synthetic Blend Motor Oil Alignment Plate, Camshaft XO-5W20-QSP (in Canada
2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 2 Installation 1. The TDC marks of the intake and exhaust CVVT sprockets are
5.7L V Chevrolet Camaro * PLEASE READ THIS FIRST * ENGINE IDENTIFICATION VEHICLE IDENTIFICATION NUMBER (VIN) ADJUSTMENTS
5.7L V8 2001 Chevrolet Camaro 2000-01 ENGINES General Motors 5.7L V8 Chevrolet; Camaro Pontiac; Firebird * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE
Water Pump Replacement (L4)
2011 Chevrolet Equinox Equinox, Terrain VIN L Service Manual Water Pump Replacement (L4) Special Tools EN-43651 Water Pump Holding Tool For equivalent regional tools, refer to Special Tools. Removal Procedure
1996 Aerostar/Ranger/Explorer
Page 1 of 10 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Engine Front Cover SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch
Short-throw Shifter Installation Guide
Short-throw Shifter Installation Guide Removal Procedure 1) Remove the shift control knob. A. Lift up on the rear portion of the shift control closeout boot retaining ring and detach the retaining ring
COMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
1999 Oldsmobile Truck Bravada V6-4.3L VIN W
1 of 6 8/24/2015 9:53 PM 1999 Oldsmobile Truck Bravada V6-4.3L VIN W Vehicle» Powertrain Management» Fuel Delivery and Air Induction» Fuel Meter Body» Service and Repair CLEANING AND INSPECTION PROCEDURE
Intake Manifold Replacement
Document ID# 738735 2002 Chevrolet Chevy Suburban - 4WD Print Intake Manifold Replacement Removal Procedure Important: The intake manifold, throttle body, fuel rail, and injectors may
SECTION C Engine 5.4L (3V)
303-01C-i Engine 5.4L (3V) 303-01C-i SECTION 303-01C Engine 5.4L (3V) CONTENTS PAGE IN-VEHICLE REPAIR Engine Front Cover... 303-01C-2 303-01C-2 Engine 5.4L (3V) 303-01C-2 IN-VEHICLE REPAIR Engine Front
Engine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,
1995 Aerostar/Ranger/Explorer
Page 1 of 13 Section 03-01C: Engine, 4.0L V-6 DISASSEMBLY AND ASSEMBLY 1995 Aerostar/Ranger/Explorer Workshop Manual Engine Disassembly 1. NOTE: Before starting disassembly, remove all wiring harnesses,
OIL PUMP (G306709) DISCOVERY 3, ENGINE - TDV6 2.7L DIESEL SPECIAL TOOL(S) Crankshaft Front Seal Remover PUMP - OIL - RENEW
2005.0 DISCOVERY 3, 303-01 ENGINE - TDV6 2.7L DIESEL OIL PUMP (G306709) IN-VEHICLE REPAIR 12.60.26 PUMP - OIL - RENEW 2700 CC 4.3 USED WITHINS SPECIAL TOOL(S) 303-1120 Crankshaft Front Seal Remover 303-1122
Page 1 of 23 303-01C Engine - 3.2L Duratorq-TDCi (148kW/200PS) - Puma 2011-2014 Ranger Assembly Procedure revision date: 07/21/2016 Special Tool(s) / General Equipment Engine Base Part Number: 6L084 100-002
Intake Manifold Replacement
Page 1 of 14 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer (VIN S/T) Service Manual Engine Engine Mechanical - 4.8L, 5.3L, and 6.0L Repair Instructions - On Vehicle Document ID:
Valves and Unit Injectors, Adjustment
Volvo Trucks North America Greensboro, NC USA DService Bulletin Trucks Date Group No. Page 3.2007 214 93 1(19) Valves and Unit injectors Adjustment D13F Valves and Unit Injectors, Adjustment W2005941 This
2.4L 4-CYL - VINS [F,H,S]
![2.4L 4-CYL - VINS [F,H,S]](/thumbs/72/66412829.jpg "2.4L 4-CYL - VINS [F,H,S]")
2.4L 4-CYL - VINS [F,H,S] 1990 Nissan 240SX 1990 ENGINES Nissan 2.4L 4-Cylinder Axxess, Pickup, Stanza, 240SX * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article,
Page 1 of 75 303-01D Engine - 5.2L 32V Ti-VCT 2016 Mustang Assembly Procedure revision date: 12/15/2016 Special Tool(s) / General Equipment Engine Base Part Number: 6L084 205-142 (T80T-4000-J) Installer,
IN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent
303-01A-1 IN-VEHICLE REPAIR Cylinder Head Special Tool(s) Torque Wrench Extension 303-575 (T97T-6256-F) or equivalent Special Tool(s) 303-01A-1 Timing Tool, Crankshaft TDC 303-573 (T97T-6303-A) or equivalent
Wiper and Washer Systems: All Technical Service Bulletins Service Procedure 1. Turn ignition switch to the "Accessory" position.
1998 Buick Century V6-3100 3.1L VIN M SFI Page 1 Wiper and Washer Systems: All Technical Service Bulletins Service Procedure 1. Turn ignition switch to the "Accessory" position. 2. Set wiper switch to
Lubricating Oil Pan
007-025 Lubricating Oil Pan Preparatory Steps Batteries can emit explosive gases. To reduce the possibility of personal injury, always ventilate the compartment before servicing the batteries. To reduce
Valve Rocker Arm and Push Rod Installation (6.2L LS3)
9. Tighten the cylinder head bolts: 10.1. Tighten the M11 cylinder head bolts (1-10) a first pass in sequence to 30 N m (22 lb ft). 10.2. Tighten the M11 cylinder head bolts (1-10) a second pass in sequence
4. LUBRICATION SYSTEM
4 LUBRICATION SYSTEM Rocker Arm Shaft Crankshaft Oil Filter Screen Oil Pump 4-0 SERVICE INFORMATION... 4-1 ENGINE OIL/OIL FILTER...4-2 TROUBLESHOOTING... 4-1 OIL PUMP...4-3 SERVICE INFORMATION GENERAL
Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical 17 Engine-Lubrication system (Page GR-17)
17 Engine-Lubrication system (Page GR-17) Lubrication system components, removing and installing Oil pressure and oil pressure switch, checking Sump, removing and installing Valve gear, servicing (Page
Crankshaft Rear Seal with Retainer Plate
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Crankshaft Rear Seal with Retainer Plate Special Tool(s) Installer, Crankshaft Rear
Water Pump Replacement (L4)
1 of 9 9/5/2017, 3:07 PM 2014 Chevrolet Captiva (VIN C) Antara, Captiva Service Manual 5565211 Engine/Propulsion Engine Cooling Repair Instructions Document ID: 2643411 Water Pump Replacement (L4) Special
2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...
Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine
This information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis.
Volvo Trucks North America Greensboro, NC USA Engine, Replacement DService Bulletin Trucks Date Group No. Page 10.2007 210 139 1(47) Engine, Replacement Volvo D16F VNL, VT W2005773 This information covers
1991 Volkswagen Vanagon Syncro
corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at
Page 1 of 8 Section 03-01: Engine, 4.6L IN-VEHICLE SERVICE 1994 Town Car/Crown Victoria/Grand Marquis Workshop Manual Oil Pan and Oil Pump Screen Cover and Tube Town Car Removal 1. Disconnect battery ground
Dana Spicer Axles & Brakes
Dana Spicer Axles & Brakes ABIB-0202R1 Information Bulletin Bulletin Type: Service/Parts Topic: Carrier to Housing Leak Repair Procedure Affected Models: D & R 404 Family of Tandem Drive Axles This document
Page 1 of 14 Oil Pan Removal & Installation 4.2L Engine 4WD Vehicles To Remove: 1. Before servicing the vehicle refer to the precautions at the beginning of this section. 2. Raise and support the vehicle.
Lubrication system components, removing and installing
17-1 Lubrication system components, removing and installing Note: If large quantities of metal particles or other deposits (caused, for example, by partial seizure of the crankshaft or conrod bearings)
2008 F-Super Duty Workshop Manual
Page 1 of 13 SECTION 303-04C: Fuel Charging and Controls 6.4L Diesel 2008 F-Super Duty 250-550 Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/04/2009 Fuel Injection Pump High Pressure,
NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
Oil Cooler Thermostat for LS & Vortec Series Engines, Rear Sump
Oil Cooler Thermostat for LS & Vortec Series Engines, Rear Sump Part No. EGM-114 Made in USA IMPORTANT: Please read these instructions in their entirety prior to installation. Rev 170510 Applications &
1 of 10 2/10/2017 5:20 PM
1 of 10 2/10/2017 5:20 PM Crankshaft Pulley Removal NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure. The crankshaft
2002 F-150 Workshop Manual
Page 1 of 8 SECTION 307-01B: Automatic Transmission 4R70W 2002 F-150 Workshop Manual REMOVAL Procedure revision date: 04/02/2003 Transmission Special Tool(s) Retainer, Torque Converter 307-346 (T97T-7902-A)
Copper Sleeve, Unit Injector, Replacement
Volvo Trucks North America Greensboro, NC USA This service bulletin replaces SB 237-46, Copper Sleeve, Unit Injector, Replacement dated 6.2007, publication no. PV776-20177417. DService Bulletin Trucks
Draining and Filling Cooling System
1996 Chevrolet/Geo Monte Carlo Draining and Filling Cooling System Correct Fill Ratios 1. Ethylene glycol/water fill ratios have been established to ensure a minimum of 50 percent ethylene glycol in the
WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
ASSEMBLY. Engine. Special Tool(s) Installer, Crankshaft Vibration Damper (T74P-6316-B) Special Tool(s)
303-01A-1 ASSEMBLY Engine Special Tool(s) Tensioner, Timing Chain 303-571 (T97T-6K254-A) Special Tool(s) 303-01A-1 Installer, Crankshaft Vibration Damper 303-102 (T74P-6316-B) Holding Tool, Camshaft Sprocket
Cylinder Head Installation - Left Side
Cylinder Head Installation - Left Side Tools Required J 36660-A Torque Angle Meter 1. Install the cylinder head locator dowel pins, if necessary. 2. Inspect the cylinder head locator dowel pins for proper
Lubrication system components, removing and installing
Page 1 of 33 17-1 Lubrication system components, removing and installing WARNING! Do not re-use any fasteners that are worn or deformed in normal use. Some fasteners are designed to be used only once,
Engine Front Cover. Special Tool(s) 3-Jaw Puller 303-D121 or equivalent. Installer, Front Cover Oil Seal (T88T-6701-A)
SECTION 303-01B: Engine 4.6L (3V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/23/2008 Engine Front Cover Special Tool(s) 3-Jaw Puller 303-D121 or equivalent Installer, Front
GROUP 11A 11A-1 CONTENTS GENERAL DESCRIPTION... 11A-2 CAMSHAFT OIL SEAL... 11A-18 DIAGNOSIS... 11A-2 SPECIAL TOOLS... 11A-3
11A-1 GROUP 11A CONTENTS GENERAL DESCRIPTION 11A-2 DIAGNOSIS 11A-2 SPECIAL TOOLS 11A-3 ON VEHICLE SERVICE 11A-5 DRIVE BELT TENSION CHECK AND ADJUSTMENT 11A-5 POWER STEERING OIL PUMP DRIVE BELT TENSION
2007 Explorer/Mountaineer/Explorer Sport Trac Workshop Manual MERCON V
2007 Explorer SECTION 307-01A: Automatic Transaxle/Transmission 5R55S 2007 Explorer/Mountaineer/Explorer Sport Trac Workshop Manual Report a problem with this article IN-VEHICLE REPAIR Procedure revision
Draining and Filling Cooling System
2000 GMC Truck Sonoma Pickup - 2WD Draining and Filling Cooling System Engine Coolant Recycling The use of a waterless, GM approved coolant recycling system on the vehicle eliminates the need for evacuation.
1999 Acura SLX. Fig. 6: Identifying Piston & Connecting Rod Size Courtesy of ISUZU MOTOR CO.
3. Check cylinder bore to determine piston-to-cylinder clearance. Clearance should be within specification. See PISTONS, PIN & RINGS table under ENGINE SPECIFICATIONS. Fig. 6: Identifying Piston & Connecting
4. LUBRICATION SYSTEM
4 4 LUBRICATION SYSTEM LUBRICATION SYSTEM DIAGRAM ---------------------------------- 4-1 SERVICE INFORMATION------------------------------------------------ 4-2 TROUBLESHOOTING-----------------------------------------------------
SMU - Revised Timing Chain, Sprockets, Tensioner Installation Procedure # (Feb 9, 2000)
1998 Pontiac Grand Am SMU - Revised Timing Chain, Sprockets, Tensioner Installation Procedure #00-06-01-002 - (Feb 9, 2000) Revised Timing Chain, Sprockets, Tensioner Installation Procedure 1998-1999 Chevrolet
ENGINE LUBRICATION 12-1 CONTENTS GENERAL INFORMATION... 2 LUBRICANTS... 3 SPECIAL TOOLS... 3 ENGINE OIL COOLER ON-VEHICLE SERVICE...
12-1 ENGINE LUBRICATION CONTENTS 12109000129 GENERAL INFORMATION... 2 LUBRICANTS... 3 SPECIAL TOOLS... 3 ON-VEHICLE SERVICE... 3 Engine Oil Check... 3 Engine Oil Replacement... 3 Oil Filter Replacement...
IN-VEHICLE REPAIR. Engine Front Cover
303-01B-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01B-1 Special Tool(s) Motorcraft SAE 5W-20 WSS-M2C930-A Premium Synthetic Blend 3-Jaw Puller Motor Oil 303-D121 XO-5W20-QSP
5.0L 4V DOHC Proper Remote Filter Plumbing and Priming Procedures. 5.0L DOHC typical oil flow diagram
!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. 5.0L 4V DOHC Proper Remote Filter Plumbing and Priming Procedures 5.0L DOHC typical oil flow diagram Proper Plumbing of
Racing Oil Pan Trap-Door Inserts for Chevrolet Corvette (C5)
Racing Oil Pan Trap-Door Inserts for 1997-2004 Chevrolet Corvette (C5) Part No. EGM-202 Made in USA Important: Read these instructions in their entirety prior to installation. Rev 170104 Applications This
ADAPTER INSTALLATION INSTRUCTIONS
ENGINE APPLICATION YEARS/CID: V8 CHRYSLER 54-58, DODGE 53-58, DESOTO 52-58, PLYMOUTH 55-58 TRANS APPLICATION YEAR/MODEL: CHEVY AUTO PG, TH350, 400, 700R4, 200-4R IMPORTANT: THIS IS A HIGH PERFORMANCE PART
Zoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Service and Repair» Procedures» Removal Cylinder Heads http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=376&nonstandardid=682956&vehicleid=45317&windowname=maina
4. LUBRICATION SYSTEM
4 4 LUBRICATION SYSTEM SERVICE INFORMATION------------------------------------------------ 4-1 TROUBLESHOOTING----------------------------------------------------- 4-1 ENGINE OIL/OIL FILTER ------------------------------------------------
Page 1 of 5 Section 03-01C: Engine, 4.0L V-6 IN-VEHICLE SERVICE Workshop Manual Camshaft SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Sensor Adjusting Wrench T94T-12270-A Removal NOTE: It is
LA1, LNJ, LG8, LL1, LX9, L82, LL2, LB8, LHO, LG5, LB6, LE2, LQ1, LH7, LC1, L44, LZ4, LZE, LZ9, LGD, LZ8, LZG)
#05-06-01-019F: Engine Oil Leak at Crankshaft Rear Main Oil Seal (Install Revised Crankshaft Rear Main Oil Seal Using Revised Rear Main Seal Installer and Remover Tools) - (Oct 2, 2007) Subject: 60 Degree
SECTION C Engine 5.4L (4V)
303-01C-i Engine 5.4L (4V) 303-01C-i SECTION 303-01C Engine 5.4L (4V) CONTENTS PAGE IN-VEHICLE REPAIR Timing Drive Components... 303-01C-2 303-01C-2 Engine 5.4L (4V) 303-01C-2 IN-VEHICLE REPAIR Timing
Zoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
AJV8 Engine Assembly. AJV8 Engine Assembly
AJV8 Engine Assembly Contents Cylinder Block Dowels, Plugs and Pipes 2 4 Crankshaft Bearing and Cylinder Bore Dimensions 5 9 Bearing Measuring 6 Engine Dimensions and Codes 6 7 Main Bearing Selection Chart
Fig. 6: Assembling Piston & Rod. NOTE: Notch must face forward Toyota Starlet CRANKSHAFT MAIN BEARINGS
connecting rods are marked for reassembly. 3. Thoroughly clean and inspect all components. Coat pin with engine oil and heat piston to 158-176 F (70-80 C). Pin should push fit with thumb pressure through
IN-VEHICLE REPAIR. Output Shaft Speed (OSS) Sensor. Removal
307-01-1 Automatic Transaxle/Transmission 6F50 307-01-1 IN-VEHICLE REPAIR Output Shaft Speed (OSS) Sensor Material Item MERCON V Automatic Transmission Fluid XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada)
CLUTCH COMPONENT LOCATION INDEX
2005 TRANSMISSION Clutch - MX-5 Miata CLUTCH COMPONENT LOCATION INDEX Fig. 1: Identifying Clutch Components GENERAL PROCEDURES (CLUTCH) PRECAUTION Clutch pipe If any clutch pipe has been disconnected anytime
Oil Cooler Thermostat for GM LS Series Engines, Rear Sump
Oil Cooler Thermostat for GM LS Series Engines, Rear Sump Part No. EGM-112 Made in USA IMPORTANT: Please read these instructions in their entirety prior to installation. Rev 180412 Applications 1997+ aluminum
Fastener Tightening Specifications Specification
2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt
Disconnect the breather tube from the air cleaner outlet duct.
Disconnect the breather tube from the air cleaner outlet duct. Disconnect the IAT sensor harness connector. Remove the air cleaner outlet duct retaining wingnut. Separate the air cleaner outlet duct from
Document ID# Cadillac CTS
Document ID# 1739230 2005 Cadillac CTS Engine Oil Leak at Crankshaft Rear Main Oil Seal (Install Revised Crankshaft Rear Main Oil Seal Using Revised Rear Main Seal Installer) #05-06-01-019B - (Dec 6, 2005)
2003 F-Super Duty /Excursion Workshop Manual
Page 1 of 16 SECTION 303-01C: Engine 7.3L Diesel DISASSEMBLY Procedure revision date: 05/21/2002 Engine Printable View (1761 KB) Special Tool(s) Cylinder Head Lifting Tool (D94T-6000-B) 303-D098 Damper
Direct Shift Gearbox (DSG) Mechatronic unit J743, removing and installing. - Loosen bolts - arrows - of oil pan - A - in diagonal sequence and remove.
- Loosen bolts - arrows - of oil pan - A - in diagonal sequence and remove. Note: Some transmission oil remains in the oil pan because not all of it can drain out. - Remove oil pan together with oil pan
SECTION Automatic Transaxle/Transmission 6R80
307-01-i Automatic Transaxle/Transmission 6R80 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 6R80 CONTENTS PAGE IN-VEHICLE REPAIR Main Control... 307-01-2 307-01-2 Automatic Transaxle/Transmission
Workshop Manual. F-Super Duty : Powertrain. 03: Engine
Workshop Manual 1999 F-Super Duty 250-550 3: Powertrain 03: Engine 1999 F-Super Duty 250-550 Contents/Index GROUP 03: Engine SECTION 303-00: Engine System General Information SECTION 303-01A: Engine 5.4L
Disassembly and Assembly
SENR9973-01 September 2007 Disassembly and Assembly 400C Industrial Engine HB (Engine) HD (Engine) HH (Engine) HL (Engine) HM (Engine) HN (Engine) HP (Engine) HR (Engine) Important Safety Information Most
11/30/2017 # F: Engine Oil Leak at Crankshaft Rear Main Oil Seal (Install Revised Crankshaft Rear Main Oil Seal Using Revised Rear Main S
2001 DeVille Subject: 60 Degree V6 Engine Oil Leak at Crankshaft Rear Main Oil Seal (Install Revised Crankshaft Rear Main Oil Seal Using Revised Rear Main Seal Installer and Remover Tools) Report a problem
13. CRANKCASE/CRANKSHAFT/BALANCER/PISTON/CYLINDER
13. CRANKCASE/CRANKSHAFT/BALANCER/PISTON/CYLINDER COMPONENT LOCATION 13-2 SERVICE INFORMATION 13-3 TROUBLESHOOTING 13-4 CRANKCASE SEPARATION 13-5 CRANKSHAFT 13-7 MAIN JOURNAL BEARING 13-9 CRANKPIN BEARING
Draining and Filling Cooling System
2001 Chevrolet Impala Draining and Filling Cooling System Ethylene glycol/water fill ratios have been established to ensure a minimum of 50 percent ethylene glycol. Ensure that all the engine block drains
1. Install clean paper and/or shop towels between the electronic brake control module assembly (EBCM) and the inner fender.
Electronic Brake Control Module (EBCM) Replacement Removal Procedure Caution: Refer to Brake Fluid Irritant Caution in Service Precautions. Notice: Refer to Brake Fluid Effects on Paint and Electrical
Lubrication system components
17-1 Lubrication system components If you find metal shavings or large quantities of metal particles (possibly caused by partial seizure of crankshaft and connecting rod bearings) in the engine oil while
2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing
1 of 25 8/18/2011 6:10 PM 2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing Cylinder head/gasket, replacement
Remove. Note : Make sure the puller capscrews are threaded all the way through the puller before applying pressure to the puller screw.
(/qs3/pubsys2/xml/en/manual/3666139/3666139-titlepage.html) Remove WARNING Do not remove the pressure cap from a hot engine. Wait until the coolant temperature is below 50 C [120 F] before removing the