FUEL SENDER ASSEMBLY REPLACEM... FUEL TANK REPLACEMENT (CAB/CHASSIS FRONT) (ENGINE CONTROLS 4.8L, 5.3L, AND 6.0L) Document ID#
|
|
- Thomasina Thornton
- 5 years ago
- Views:
Transcription
1 FUEL SENDER ASSEMBLY REPLACEM... FUEL TANK REPLACEMENT (CAB/CHASSIS FRONT) (ENGINE CONTROLS 4.8L, 5.3L, AND 6.0L) Document ID# Fuel Tank Replacement (Cab/Chassis Front) Removal Procedure 1/10
2 1. Relieve the fuel system pressure. Refer to the Fuel Pressure Relief. 2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 3. Drain the fuel tank. Refer to Fuel Tank Draining (Pickup). 4. Remove the fuel tank shield (1). 2/10
3 5. Disconnect the fuel fill and vent pipe (2) from the fuel tank. 3/10
4 6. With the aid of an assistant, support the fuel tank. 7. Remove the fuel tank strap attaching bolts. 8. Remove the fuel tank straps (1). 9. Carefully lower the fuel tank slightly. 10. Disconnect the fuel and evaporative emission (EVAP) pipes. Refer to Metal Collar Quick Connect Fitting Service. 4/10
5 11. Disconnect the fuel sender and the fuel pressure sensor harness connectors. 12. Remove the fuel tank. 13. Place the fuel tank in a suitable work area. 14. Remove the fuel sender assembly from the fuel tank. Refer to Fuel Sender Assembly Replacement. 15. Cap the fuel and EVAP pipes on the vehicle in order to prevent possible fuel system contamination. Installation Procedure 5/10
6 1. Install the fuel sender assembly to the fuel tank. Refer to Fuel Sender Assembly Replacement. 2. Remove the caps from the fuel and EVAP pipes. 3. With the aid of an assistant, support and partially raise the fuel tank. 4. Connect the fuel sender and the fuel pressure sensor harness connectors. 5. Connect the fuel and EVAP pipes. Refer to Metal Collar Quick Connect Fitting Service. 6. Fully raise the fuel tank (2). 6/10
7 7. Install the fuel tank straps (1). Notice: Refer to Fastener Notice in Cautions and Notices. 8. Install the fuel tank strap attaching bolts. Tighten: Tighten the bolts to 40 [n m] (30 lb ft). 7/10
8 9. Connect the fuel fill and vent pipe (2) to the fuel tank. Tighten: Tighten the hose clamps to 2.5 [n m] (22 lb in). 8/10
9 10. Install the fuel tank shield (1). 11. Lower the vehicle. 12. Refill the fuel tank (2). 13. Install the fuel filler cap. 14. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection (Single Battery)Battery Negative Cable Disconnection and Connection (Auxiliary Battery) in Engine Electrical. 9/10
10 15. Use the following procedure in order to inspect for leaks: 6.1. Turn ON the ignition, with the engine OFF, for 2 seconds Turn OFF the ignition for 10 seconds Turn ON the ignition, with the engine OFF Inspect for fuel leaks. 16. Install the engine sight shield. Refer to Upper Intake Manifold Sight Shield Replacement (4.8L, 5.3L, and 6.0L Engines)Upper Intake Manifold Sight Shield Replacement (6.0L Engine w/ RPOs Y91 and Z88) in Engine Mechanical. "Portions of materials contained herein have been reprinted with permission of General Motors Corporation, Service and Parts Operations" License Agreement # Copyright Service Repair Solutions, Inc. 10/10
PRIMARY FUEL TANK MODULE REPL... FUEL TANK REPLACEMENT (FWD) (ENGINE CONTROLS 3.4L) Document ID#
PRIMARY FUEL TANK MODULE REPL... FUEL TANK REPLACEMENT (FWD) (ENGINE CONTROLS 3.4L) Document ID# 1389484 Fuel Tank Replacement (FWD) Removal Procedure Caution: Do not allow smoking or the use of open flames
More information2009 Buick Truck Enclave AWD V6-3.6L
ALLDATA Repair - 2009 Buick Truck Enclave AWD V6-3.6L - Service and Repair Page 1 of 10 2009 Buick Truck Enclave AWD V6-3.6L Vehicle» Powertrain Management» Fuel Delivery and Air Induction» Fuel Tank Unit»
More informationCylinder Head Replacement
CYLINDER HEAD REPLACEMENT (EN... CYLINDER HEAD REPLACEMENT (ENGINE MECHANICAL - 1.6L) Document ID# 1430093 Cylinder Head Replacement Tools Required J 45059 Angle Meter KM-470-B Angular Torque Gauge J 42492-A
More informationZoom and Print Options
Vehicle» Powertrain Management» Fuel Delivery and Air Induction» Fuel Tank» Service and Repair» Procedures» Fuel Tank Removal and Installation REMOVAL WARNING: DO NOT SMOKE OR CARRY LIGHTED TOBACCO OR
More informationCYLINDER HEAD REPLACEMENT - R... CYLINDER HEAD REPLACEMENT - RIGHT SIDE (ENGINE MECHANICAL - 4.8L, 5.3L, AND 6.0L) Document ID#
CYLINDER HEAD REPLACEMENT - R... CYLINDER HEAD REPLACEMENT - RIGHT SIDE (ENGINE MECHANICAL - 4.8L, 5.3L, AND 6.0L) Document ID# 1524388 Cylinder Head Replacement - Right Side Tools Required J 42385-200
More informationFUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY Removal and Installation REMOVAL WARNING: Follow the "General Precautions" before working on the fuel system. Refer to "General Precautions".
More informationFUEL TANK DRAINING. Special Tool(s) Special Tool(s)
FUEL TANK DRAINING Special Tool(s) Zoom Special Tool(s) WARNING: Do not smoke, carry lighted tobacco or open flame of any type when working on or near any fuel-related component. Highly flammable mixtures
More informationIntake Manifold Replacement
Page 1 of 14 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer (VIN S/T) Service Manual Engine Engine Mechanical - 4.8L, 5.3L, and 6.0L Repair Instructions - On Vehicle Document ID:
More informationFuel System Diagnosis
Page 1 of 6 2001 Chevrolet Express Express, Savana (VIN G) Service Manual Engine Engine Controls - 5.0L and 5.7L Diagnostic Information and Procedures Document ID: 720867 Fuel System Diagnosis Circuit
More information1995 Chevrolet S10 Pickup - 2WD
1995 Chevrolet S10 Pickup - 2WD Submodel: Engine Type: Liters: Fuel Delivery: Fuel: Draining Procedure Caution: Gasoline or gasoline vapors are highly flammable. A fire could occur if an ignition source
More informationSTEERING COLUMN REPLACEMENT (... STEERING COLUMN REPLACEMENT (ELECTRONIC) (STEERING WHEEL AND COLUMN) Document ID#
STEERING COLUMN REPLACEMENT (... STEERING COLUMN REPLACEMENT (ELECTRONIC) (STEERING WHEEL AND COLUMN) Document ID# 1641009 Steering Column Replacement (Electronic) Removal Procedure Caution: Refer to SIR
More informationINTAKE MANIFOLD INSPECTION/REPLACEMENT
ATTACHMENT III Owner Notification Program 99M01 INTAKE MANIFOLD INSPECTION/REPLACEMENT AFFECTED VEHICLES: 1997 AND 1998 CROWN VICTORIA POLICE INTERCEPTOR VEHICLES WITH 4.6L SOHC ENGINES BUILT AT THE ST.
More information2004 Lincoln LS Workshop Manual
SECTION 310-00: Fuel System 2004 Lincoln LS Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/23/2004 Fuel Tank and Filler Pipe Printable View (541 KB) Special Tool(s) Fuel Drain Hose
More informationCOMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
More informationDisconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.
ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.
More informationEvaporative Emission Control System Operation Description (Enhanced)
Page 1 of 7 1999 Chevrolet Chevy Suburban - 2WD Escalade, Pickup (Classic), Suburban, Tahoe, Yukon (VIN C/K) Service Manual Document ID: 222842 Evaporative Emission Control System Operation Description
More informationPage 1 of 6 Section 07-01A: Transaxle, Automatic CD4E 1996 Probe Workshop Manual REMOVAL Procedure revision date: 06/14/2000 Transaxle Item Part Number Description 1 10655 Battery 2 10732 Battery Tray
More informationFuel System Diagnosis
Page 1 of 6 2001 Chevrolet Malibu Malibu (VIN N) Service Manual Engine Engine Controls - 3.1L (LG8) Diagnostic Information and Procedures Document ID: 704675 Fuel System Diagnosis System Description When
More information1999 Oldsmobile Truck Bravada V6-4.3L VIN W
1 of 6 8/24/2015 9:53 PM 1999 Oldsmobile Truck Bravada V6-4.3L VIN W Vehicle» Powertrain Management» Fuel Delivery and Air Induction» Fuel Meter Body» Service and Repair CLEANING AND INSPECTION PROCEDURE
More informationFUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY PFP:17042 Removal and Installation EBS00M47 1. Lock ring 2. Fuel level sensor, fuel filter, and fuel pump assembly FL-6 3. Fuel level sensor,
More informationREMOVAL AND INSTALLATION
310-00-1 Fuel System 310-00-1 REMOVAL AND INSTALLATION Fuel Tank and Filler Pipe Special Tool(s) Fuel Tank Drain Hose 310-F013 2. NOTE: Steps 2 through 5 are only necessary if servicing the fuel tank or
More informationPage 1 of 5 2004 Pontiac GRAND PRIX Submodel: Engine Type: V6 Liters: 3.8 Fuel Delivery: FI Fuel: GAS Oil Pan Replacement Removal Procedure Disconnect the negative battery cable. Refer to Battery Negative
More informationFuel supply system components, removing and installing
20-1 Fuel supply system components, removing and installing Checking fuel system for leaks Removing and installing fuel filter and draining water, engine code AAZ: Repair Manual, 1.9 Liter 4-Cyl. 2V Eco-Diesel
More informationEngine Cylinder Head Installation
Engine Cylinder Head Installation Important: Install the cylinder head without the camshafts. 1. Install the engine cylinder head to the engine block. 2. Install the AIR pump bolt and fir tree fastener
More information1 of 12 10/5/2015 8:11 AM
1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
More informationWater Pump Replacement (L4)
1 of 9 9/5/2017, 3:07 PM 2014 Chevrolet Captiva (VIN C) Antara, Captiva Service Manual 5565211 Engine/Propulsion Engine Cooling Repair Instructions Document ID: 2643411 Water Pump Replacement (L4) Special
More informationPlastic Collar Quick Connect Fitting Service
2004 Chevrolet Silverado 1500 -Fuel Systems > Fuel Controls -4.8L, 5.3L, And 6.0L > Repair Ins... Page 1 of 10 2004 Chevrolet Silverado 1500 : Fuel Systems > Fuel Controls - 4.8L, 5.3L, And 6.0L > Repair
More information2002 Chevrolet Blazer
The blower motor will operate in any switch position, as long as the ignition switch is in the RUN position and the mode switch is in any position other than OFF. When the ignition switch is on, power
More informationIntake Components 1117
Item Part Number Description 1 W705654 Bolt 2 N807309 Bolt (2 req'd) 3 9F460 Bracket 4 N807071 Bolt (5 req'd) 5 9A448 Intake manifold (upper) 6 9E498 Vacuum harness 7 9F792 Fuel injection supply manifold
More informationFUEL SYSTEM SECTION CONTENTS B ENGINE FL-1
B ENGINE A SECTION FUEL SYSTEM FL C D CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 PREPARATION... 3 Special Service Tools...
More informationFUEL SYSTEM SECTION CONTENTS B ENGINE FL-1
B ENGINE A SECTION FUEL SYSTEM FL C D CONTENTS E PREPARATION... 2 Special Service Tools... 2 Commercial Service Tool... 2 FUEL SYSTEM... 3 Checking Fuel Lines... 3 General Precautions... 3 FUEL LEVEL SENSOR
More informationCAMSHAFT TIMING CHAIN, SPROCK... CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT (LE5 OR LE9) (ENGINE MECHANICAL - 2.2L OR 2.
CAMSHAFT TIMING CHAIN, SPROCK... CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT (LE5 OR LE9) (ENGINE MECHANICAL - 2.2L OR 2.4L) Document ID# 2133175 Camshaft Timing Chain, Sprocket, and Tensioner
More informationFuel Pickup Kit GM 6.6L Duramax ( )
PPEdiesel.com GM 6.6L Duramax 2006-2008 (113052000) Installation Guide Technical Support (714) 985-4825 Rev: 06/08/18 v7a Note: LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER BE USED, OR REGISTERED
More informationWater Pump Replacement (L4)
2011 Chevrolet Equinox Equinox, Terrain VIN L Service Manual Water Pump Replacement (L4) Special Tools EN-43651 Water Pump Holding Tool For equivalent regional tools, refer to Special Tools. Removal Procedure
More information1991 Volkswagen Vanagon Syncro
corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at
More informationIN-VEHICLE REPAIR. Upper Intake Manifold
303-01-1 Engine 3.9L and 4.2L 303-01-1 IN-VEHICLE REPAIR Upper Intake Manifold Special Tool(s) Remover, Spark Plug Wire 303-106 (T74P-6666-A) Material Item Silicone Brake Caliper Grease and Dielectric
More informationP0441-EVAP PURGE SYSTEM PERFO... P0441-EVAP PURGE SYSTEM PERFORMANCE
P0441-EVAP PURGE SYSTEM PERFO... P0441-EVAP PURGE SYSTEM PERFORMANCE For a complete wiring diagram, refer to the Wiring Information. Theory of Operation EVAP SYSTEM COMPONENTS CALLOUT DESCRIPTION 1 Filter
More informationFUEL SYSTEM SECTION FL CONTENTS B ENGINE FL-1
B ENGINE SECTION FL A FUEL SYSTEM FL C D CONTENTS E PREPARATION... 2 Special Service Tools... 2 Commercial Service Tool... 2 FUEL SYSTEM... 3 Checking Fuel Lines... 3 General Precautions... 3 FUEL LEVEL
More information255 Liter/Hr, In Tank Fuel Pump For Chrysler Front Wheel Drive Vehicles Catalog # INSTALLATION INSTRUCTIONS
255 Liter/Hr, In Tank Fuel Pump For 1984-1990 Chrysler Front Wheel Drive Vehicles Catalog # 17934 INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before installing your new In-Tank
More information2014 Ford Edge SE ENGINE Fuel Tank & Lines - Edge, MKX
17. Remove the 2 nuts, 7 bundle retainer clips and remove the fuel supply and EVAP vapor tube assembly. To install, tighten to 9 Nm (80 lb-in). 18. To install, reverse the removal procedure. FUEL LINES
More informationDTC P0174 Fuel Trim System Lean Bank 2
2000 Chevrolet/Geo S10 Pickup - 4WD DTC P0174 Fuel Trim System Lean Bank 2 Circuit Description In order to provide the best possible combination of driveability, fuel economy, and emission control, the
More informationFuel System Diagnosis
Page 1 of 9 1999 Chevrolet Express Express, Savana (VIN G) Service Manual Engine Engine Controls - 5.0L and 5.7L Diagnostic Information and Procedures Document ID: 412957 Fuel System Diagnosis Circuit
More informationJohn Deere. MODEL: 2030 Tractor JD-S-TM10S1
John Deere MODEL: 2030 Tractor THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF JOHN DEERE OR IT'S SUCCESSORS. JOHN DEERE AND IT'S SUCCESSORS ARE NOT RESPONSIBLE FOR THE QUALITY
More informationCylinder Head Removal
2006 Odyssey Cylinder Head Removal Report a problem with this article NOTE: Use fender covers to avoid damaging painted surfaces. To avoid damaging the wires and terminals, unplug the wiring connectors
More informationSteering Gear Replacement
Page 1 of 7 Steering Gear Replacement Removal Procedure Notice: With wheels of the vehicle facing straight ahead, secure the steering wheel utilizing steering column anti-rotation pin, steering column
More informationFUEL SYSTEM SECTION CONTENTS B ENGINE FL-1
B ENGINE A SECTION FUEL SYSTEM FL C D CONTENTS E FUEL SYSTEM... 2 Checking Fuel Lines... 2 General Precautions... 2 FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY... 3 Removal and Installation...
More informationIntake Manifold Replacement
Document ID# 738735 2002 Chevrolet Chevy Suburban - 4WD Print Intake Manifold Replacement Removal Procedure Important: The intake manifold, throttle body, fuel rail, and injectors may
More informationVehicle Level Engine, Cooling and Exhaust Engine Cylinder Head Assembly Service and Repair. Service and Repair
Page 1 of 7 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2001 Pontiac Sunfire L4-2.2L VIN 4 Conversion Calculator
More information1999 E-Series Workshop Manual
http://www.fordservicecontent.com/pubs/content/~wsxm/~mus~len/21/sxm31c16.h... Page 1 of 3 SECTION 303-01C: Engine 6.8L 1999 E-Series Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 06/30/1998
More informationOil Pan Replacement Buick Regal
2000 Buick Regal Oil Pan Replacement Removal Procedure Tools Required J 28467-90A Engine Support Adapters J 28467-B Universal Engine Support Fixture J 36462-A Engine Support Adapter Leg Set 1. Disconnect
More information11/12/2017 # C: MIL Illuminated, DTCs P0442, P0446, P0455 or P0449 Set - Fuel Tank Hard to Fill - Moisture, Water, Corrosion at EVAP Can
2009 Suburban 4WD Subject: Malfunction Indicator Lamp (MIL) Illuminated, DTCs P0442, P0446, P0455 or P0449 Set Fuel Tank Hard to Fill Moisture, Water, Corrosion at Evaporative Emissions (EVAP) Canister
More informationConnector Part Information. A1 LT BLU 115 Speaker Return - Right Rear A01 LT BLU 115 Speaker Return - Right Rear
C203 (IP HARNESS TO BODY HARN... C203 (IP HARNESS TO BODY HARNESS) (15318195 116-WAY F METRI-PACK 150,280 SERIES (BLK)) (WIRING SYSTEMS) Document ID# 358707 C203 (IP Harness to Body Harness) Connector
More informationThe following tools will be required to perform this new service procedure outlined in this bulletin:
The following new service information outlined in this bulletin will aid technicians in removal and installation of the cylinder head without the removal of the front engine cover. The new service procedure
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: August 2009
NUMBER: 8 5 09 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: August 2009 SUBJECT: CYLINDERHEADCOOLANTVENTLINE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change
More informationBEFORE BEGINNING INSTALLATION
COMPLETE CHASSIS FUEL LINE KITS For 1996-2000 Honda Civic Equipped with B-Series Engine INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most installations
More information2002 Explorer Sport/Sport Trac Workshop Manual
Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)
More informationControl Module Command EVAP Canister Purge Valve EVAP Canister Vent Valve ON Open Closed OFF Closed Open
DTC P0440 System Description The control module tests the evaporative emission (EVAP) system for a large leak. The control module monitors the fuel tank pressure (FTP) sensor signal to determine the EVAP
More informationFUEL SYSTEM PRECAUTION FU 1
2GR-FE EL EL SYSTEM EL SYSTEM PRECAUTION 1 1. EXPRESSIONS OF IGNITION SWITCH (a) The type of the ignition switch used on this model differs according to the specifications of the vehicle. The expressions
More informationEvaporative Emission Control System Operation Description
Page 1 of 5 2000 Chevrolet Venture Ext. Montana, Silhoutte, Trans Sport, Venture (VIN U) Service Manual Engine Engine Controls - 3.4L Description and Operation Evaporative Emission Control System Operation
More information10/30/2018 Intake Manifold Replacement (RPOs LY2/LY6) 2007 GMC Truck Yukon Denali MotoLogic
2007 Yukon Denali Applies to: 4.8L, 5.3L, 6.0L and 6.2L Report a problem with this article Removal Procedure 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Resonator Outlet Duct Replacement.
More informationBrake Pressure Modulator Valve Assembly Replacement (LHD)
Page 1 of 6 2007 Chevrolet Lumina VE Document ID: 1974792 Brake Pressure Modulator Valve Assembly Replacement (LHD) Removal Procedure Caution: Refer to Brake Fluid Caution in the Preface section. Caution:
More information2002 Crown Victoria/Grand Marquis Workshop Manual
Page 1 of 9 SECTION 303-04: Fuel Charging and Controls 2002 Crown Victoria/Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/13/2001 Fuel Injection Supply Manifold Material
More information2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #
2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #350-091 3239 MONIER CIRCLE, STE.5 RANCHO CORDOVA, CA 95742 916.635.4550 FAX 916.635.4632 www.ct-engineering.com INS-157 VERSION: 3.25.2009
More informationFUEL SYSTEM SECTION CONTENTS B ENGINE FL-1
B ENGINE A SECTION FUEL SYSTEM FL C D CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 PREPARATION... 3 Special Service Tools...
More information2001 Chevrolet CORVETTE
riveline Support Assembly Replacement (Automatic Transmission) 1 of 21 10/24/2012 8:58 PM 2001 Chevrolet CORVETTE Submodel: Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Driveline Support Assembly
More informationIN-VEHICLE SERVICING > VALVE COVER - RH
Page 1 of 20 Service Manual: ENGINE - 5.4L (3V)- F-150 & MARK LT IN-VEHICLE SERVICING > VALVE COVER - RH 2008 Ford Pickup 5.4L Eng F150 Material Item Specification Motorcraft Metal Surface Prep ZC-31 PAG
More information2011 Transit Connect Workshop Manual
SECTION 303-12: Intake Air Distribution and Filtering REMOVAL AND INSTALLATION Procedure revision date: 09/23/2010 Intake Air System Components - Exploded View Item Part Number 1 9F991 Throttle Body (TB)
More informationAEROMOTIVE Part # & Mustang 5.0L Stealth Fuel System Kit INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 18653 & 18654 86-93 Mustang 5.0L Stealth Fuel System Kit INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures.
More information2004 Fresh Water Cooling Installation Instructions - V-Drive Kit RK147050A
2004 Fresh Water Cooling Installation Instructions - V-Drive Kit This Page Was Intentially Left Blank TABLE OF CONTENTS 1 - FWC Kit Installation Instructions - V-Drive... Table of Contents...... 1 Installation
More information2013 Mustang Workshop Manual
32. Attach the wiring harness retainers to the LH side of the oil pan and the front oil pan stud bolts and install the 2 nuts. Tighten to 8 Nm (71 lb-in). 33. Position the underbody shield and install
More informationAEROMOTIVE Part # & Mustang Stealth Fuel Tank w/fuel pump INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 18685 &18686 86-98.5 Mustang Stealth Fuel Tank w/fuel pump INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair
More informationIntake Manifold Replacement
Page 1 of 13 Your Current Vehicle: 2008 Cadillac STS Intake Manifold Replacement Intake Manifold Replacement Removal Procedure 1. Turn the ignition OFF. 2. Remove the fuel injector sight shield. Refer
More information2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 1
2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair Timing Belt REMOVAL 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove
More informationFuel System Diagnosis
Page 1 of 6 2004 Chevrolet Chevy K Silverado - 4WD Sierra, Silverado (VIN C/K) Service Manual Engine Engine Controls - 6.6L (LLY) Diagnostic Information and Procedures Document ID: 1460257 Fuel System
More informationIntroduction & Owner Information 1 Safety Precautions 2 Parts 2 Installation Instructions 2 Tools 2 Warranty Information 6
INSTALLATION INSTRUCTIONS Gas Tank Skid Plate Kit For: Jeep YJ Kit 66550 Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have provided installation
More informationThis information covers the proper replacement procedure for the EGR valve on the Volvo D16F engine.
Volvo Trucks North America Greensboro, NC USA EGR Valve, Replacement DService Bulletin Trucks Date Group No. Page 11.2006 254 24 1(17) EGR Valve Replacement D16F W2005772 This information covers the proper
More informationFuel System Diagnosis
1996 Chevrolet Impala Caprice, Impala, Roadmaster (VIN B) Service Manual Engine Engine Controls - 4.3L (Caprice Only) and 5.7L Diagnostic Information and Procedures Document ID: 37723 Fuel System Diagnosis
More informationPRECAUTIONS ENGINE REPAIR
3234_U01.qxd 9/23/03 3:44 PM Page 13 BLAZER XTREME TRAILBLAZER BRAVADA ENVOY JIMMY 1-13 PRECAUTIONS Before servicing any vehicle, please be sure to read all of the following precautions, which deal with
More informationFuel Pickup Kit ( ) Installation Guide
2006-2008 Fuel Pickup Kit (1130520) Installation Guide Note: Legal in California only for racing vehicles which may never be used on the highway. PPE offers super tanks that are easy to install and fit
More information2003 Volkswagen Passat GL
2001-03 AUTOMATIC TRANSMISSIONS Removal & Installation - 01V APPLICATION TRANSAXLE APPLICATION Application Transaxle Model Passat 1.8L (FWD) 01V 2.8L (FWD & 4WD) 01V 4.0L (AWD) 2002-03 01V REMOVAL & INSTALLATION
More informationFU01 Tank Assembly. Copyright 1998 Inter-Industry Conference On Auto Collision Repair v.4.0
Uniform Procedures For Collision Repair FU01 Tank Assembly 1. Description This procedure describes methods for the removal and installation of a fuel tank assembly. Inspection and evaluation requirements
More informationDistributor Replacement (HVS)
1 of 8 3/3/2018, 3:02 PM 1998 Chevrolet K Pickup - 4WD Chevy Pickup, GMC Pickup, Suburban, Tahoe, Yukon VIN C/K Service Manual Engine Engine Electrical Repair Instructions Document ID: 207477 Distributor
More informationWater Pump Replacement L61
2002 Saturn VUE - AWD Water Pump Replacement L61 Tools Required J 43651 Water Pump Holding Tool Removal Procedure 1. Drain the coolant. Refer to Draining and Filling Cooling System. 2. Remove the thermostat
More information1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
More informationFront Bumper Fascia Replacement
Page 1 of 10 2008 Pontiac G8 G8 Service Manual Body Repair Bumpers and Fascias Repair Instructions Document ID: 2044380 Front Bumper Fascia Replacement Removal Procedure Caution: Refer to Safety Glasses
More information7. Evaporative Emission Control System
W1860BE.book Page 10 Tuesday, January 28, 2003 11:01 PM 7. Evaporative Emission Control System A: GENERAL The evaporative emission control system prevents fuel vapors from escaping into atmosphere. This
More information3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter
1 of 16 Transmission Replacement Tools Required ^ J 41623-B Cooler Quick Connect Tool ^ J 41160 Transmission Jack Adapter Removal Procedure 1. Remove the upper filler panel. 2. Remove the upper and lower
More information10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L
2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN
More informationDisconnect the breather tube from the air cleaner outlet duct.
Disconnect the breather tube from the air cleaner outlet duct. Disconnect the IAT sensor harness connector. Remove the air cleaner outlet duct retaining wingnut. Separate the air cleaner outlet duct from
More information2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages.
2. NOTE: Tighten the bolts in two stages. Tighten the bolts in the sequence shown. Stage 1: Tighten to 2 Nm (18 lb-in). Stage 2: Tighten to 10 Nm (89 lb-in). 3. Install the upper intake manifold. Position
More informationPage 1 of 8 Section 03-01: Engine, 4.6L IN-VEHICLE SERVICE 1994 Town Car/Crown Victoria/Grand Marquis Workshop Manual Oil Pan and Oil Pump Screen Cover and Tube Town Car Removal 1. Disconnect battery ground
More informationFuel Pickup Kit ( ) Installation Guide
Pacific Performance Engineering, Inc. PPEdiesel.com 2001-2005 Fuel Pickup Kit (113051000) Installation Guide Technical Support (714) 985-4825 Rev: 12/02/2016 v7 * Note: LEGAL IN CALIFORNIA ONLY FOR RACING
More informationSLP Camaro ZL1 STAGE 3 (650 HP)
SLP - 2012 Camaro ZL1 STAGE 3 (650 HP) PART #26002 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1
More informationSPECIAL TOOL(S) WARNING: Special Tool(s)
Special Tool(s) SPECIAL TOOL(S) WARNING: DO NOT MODIFY THE SYSTEM CONFIGURATION OR COMPONENTS OR REPLACE COMPONENTS WITH COMPONENTS NO SPECIFICALLY DESIGNED FOR USE WITH NATURAL GAS. FORD MOTOR COMPANY
More informationFREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How
1 of 29 10/12/2011 5:05 PM FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How Ford Ranger/Explorer/Mountaineer 1991-1999 Intake Manifold REMOVAL & INSTALLATION Print The engines
More informationDisconnect negative battery cable and remove coolant bottle cap.
1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use
More informationPowerstroke EGR Delete A B C
20-203 6.7 Powerstroke EGR Delete A B C D E F G H I J K Part # A B C D E F G H I J K PACKING LIST: QTY. 3 5 2 Description Sensor Bracket Exhaust Blockoff Plate Straights Barbed Brass Fitting 39 5/8 Coolant
More informationFuel Supply Component Description
1999 Chevrolet/Geo Tahoe - 4WD Fuel Supply Component Description FIGURE Central SFI Fuel System with Fuel Pressure Gauge(c) (1) Fuel Inlet (2) Bleed Hose (3) J 34730-1A Fuel Pressure Gage Assembly (4)
More informationM-9424-M50B 2012 Boss 302 Intake Manifold INSTALLATION INSTRUCTIONS
!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. WARNING: CUSTOM CALIBRATION REQUIRED! CALIBRATION NOT INCLUDED! KIT CONTENTS: 1) Intake Manifold Assembly 2) Assembly
More information