3. Using the ST, align the Top mark on crank sprocket to nine o clock position as shown in the figure
|
|
|
- Jessie Williamson
- 5 years ago
- Views:
Transcription
1 2008 Tribeca (3.6L) MECHANICAL(H6DO) > Timing Chain Assembly Report a problem with this article INSTALLATION Be careful that the foreign matter is not into or onto assembled component during installation. Apply engine oil to the all timing chain components. 1. Preparation for chain tensioner installation. (1) Insert the screw, spring pin and plunger into tensioner body. (2) Rotate the rubber mat counterclockwise while pressing the chain tensioner from upper side by hand as shown in the figure. Degrease the contact surface between plunger top portion and rubber mat to prevent slipping. (3) Insert the stopper pin into the chain tensioner body hole. 2. Set the oil pump shaft knock pin at the six o clock position as shown in the figure. 3. Using the ST, align the Top mark on crank sprocket to nine o clock position as shown in the figure 1/11
2 (A) Top mark 4. Align the intake cam sprocket to 12 o clock position as shown in the figure. (A) Align the marking (Top mark) position to 12 o clock position. (B) 6 (C) Align the exhaust cam sprocket to 12 o clock position as shown in the figure. (A) Align the marking (Top mark) position to 12 o clock position. (B) 5.5 (C) Using the ST, align the Top mark on crank sprocket to 12 o clock position as shown in the figure Piston #1 is at top dead center (TDC) position. Do not rotate the crankshaft and cam sprocket before completing timing chain installation. 2/11
3 Crank sprocket key is located at three o clock position. (A) Top mark 7. Install the chain guide (Main). 8. Install the idler sprocket and timing chain (Main). (1) Align the timing chain mark (gold) to the idler sprocket timing mark position. (2) Align the idler sprocket timing mark to the six o clock position, and then install the idler sprocket and timing chain. (3) Confirm the timing chain mark (gold) is set to the crank sprocket 12 o clock position. (4) Install the idler sprocket bolt. ST1 ST AA000 PULLEY WRENCH 18334AA000 PULLEY WRENCH PIN SET 120 N m (12.2 kgf-m, 88.5 ft-lb) 3/11
4 (A) Gold (B) Timing mark 9. Install the chain tensioner lever (Main). 10. Install the chain tensioner (Main) and pull out the stopper pin. Timing chain (Main) components assembly is completed. 4/11
5 11. Install the chain guide (LH). 12. Install the chain guide (LH: between cams). 6.4 N m (0.7 kgf-m, 4.7 ft-lb) 13. Install the timing chain (LH). 5/11
6 (1) Align the timing chain mark (blue) to the intake cam sprocket (LH) timing mark. (A) Blue (B) Timing mark (2) Align the timing chain mark (blue) to the exhaust cam sprocket (LH) timing mark. (A) Blue (B) Timing mark (3) Install the timing chain to the water pump sprocket. 6/11
7 (A) Water pump sprocket (4) Align the idler sprocket timing mark to the timing chain mark (gold). (A) Gold (B) Timing mark 14. Install the chain tensioner lever (LH). 15. Install the chain tensioner (LH) and pull out the stopper pin. 7/11
8 Confirm the bolt is attached on the side of chain tensioner housing. Timing chain (LH) components assembly is completed. 16. Install the chain guide (RH). 17. Install the chain guide (RH: between cams). 6.4 N m (0.7 kgf-m, 4.7 ft-lb) 8/11
9 18. Install the timing chain (RH). (1) Align the timing chain mark (blue) to the intake cam sprocket (RH) timing mark. (A) Blue (B) Timing mark (2) Align the timing chain mark (blue) to the exhaust cam sprocket (RH) timing mark. 9/11
10 (A) Blue (B) Timing mark (3) Align the idler sprocket timing mark to the timing chain mark (gold). (A) Gold (B) Timing mark 19. Install the chain tensioner lever (RH). 20. Install the chain tensioner (RH) and pull out the stopper pin. Timing chain (RH) components assembly is completed. 10/11
11 21. Confirm the followings after installation. CAUTION: Be sure to perform this confirmation. (1) Confirm that the idler sprocket timing mark and three timing chain marks (gold) are aligned. (2) Confirm that the crank sprocket 12 o clock position and timing chain (Main) mark (gold) are aligned. (3) Confirm that the LH cam sprocket timing mark and timing chain mark (blue) are aligned. (4) Confirm that the RH cam sprocket timing mark and timing chain mark (blue) are aligned. (5) Confirm that the bolts are tightened to the specified tightening torque. 22. Confirm that there are no abnormalities, while turning the crankshaft in the engine rotating direction using ST. CAUTION: Be sure to perform this confirmation. 23. Install the chain cover. MECHANICAL(H6DO) > Chain Cover > INSTALLATION 24. Install the crank pulley. MECHANICAL(H6DO) > Crank Pulley > INSTALLATION 25. Install the V-belt. MECHANICAL(H6DO) > V-belt > INSTALLATION 26. Fill engine oil. LUBRICATION(H6DO) > Engine Oil > REPLACEMENT 27. Confirm that there are no oil leakage at the chain cover mating surface. 28. Install the radiator. COOLING(H6DO) > Radiator > INSTALLATION 11/11
15.Timing Chain Assembly
15. A: REMOVAL 1. TIMING CHAIN RH When replacing a single part, perform the work with the engine assembly installed to body. 1) Remove the chain cover. 2) Using
VALVE CLEARANCE (K3-VE)
ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) 25 ENGINE MECHANICAL VALVE CLEARANCE (K3-VE) INSPECTION 1. DISCONNECT NEGATIVE BATTERY TERMINAL (See page RS-164.) 2. ROVE ENGINE UNDER COVER 3. DRAIN ENGINE COOLANT
TIMING CHAIN COMPONENTS
Page 1 of 30 TIMING CHAIN COMPONENTS Fig. 46: Identifying Camshaft Timing Oil Control Valve Assembly Components With Torque Page 2 of 30 Specifications (1 Of 3) Fig. 47: Identifying Camshaft Timing Oil
2nd Timing Chain and Chain Tensioner Components S6RW0C
8) Install cylinder head cover referring to Cylinder Head Cover Removal and Installation. 9) Install oil pan. Refer to Oil Pan and Oil Pump Strainer Removal and Installation in Section 1E for installation.
MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing.
MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing. ST 499817100 ENGINE STAND Apply a coat of engine oil to the bearing and
GM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions
GM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions Set Includes: Locking Tool... 536594 Locking Tool... 536595 Crankshaft Holding Tool... 536596 Alignment Gauge... 536608 Belt Installation
15.Timing Belt. Timing Belt A: REMOVAL ME(STI) TIMING BELT
15.Timing Belt A: REMOVAL NOTE: Perform the work with the engine installed to body when replacing a single part. For operation procedures, refer to Timing Belt in the PM section.
11.Preparation for Overhaul
11.Preparation for Overhaul A: PROCEDURE 1) After removing the engine from body, secure it in the ST shown below. ST1 498457000 ENGINE STAND ADAPTER RH ST2 498457100 ENGINE STAND ADAPTER LH ST3 499817000
15.Timing Belt Assembly
MECHANICAL 15.Timing Belt Assembly A: REMOVAL 1. TIMING BELT 1) Remove the V-belt. 2) Remove the crank pulley.
15.Timing Belt. Timing Belt A: REMOVAL ME(H4DOTC) TIMING BELT
15. A: REMOVAL 1. TIMING BELT 1) Remove the V-belts. 2) Remove the crank pulley. 3) Remove the timing belt cover.
2nd Timing Chain and Chain Tensioner Components S6RW0C
8) Install cylinder head cover referring to Cylinder Head Cover Removal and Installation. 9) Install oil pan. Refer to Oil Pan and Oil Pump Strainer Removal and Installation in Section 1E for 10) Install
Service and Repair. a. Remove the 2 nuts and 2 upper radiator support. b. Lift out the radiator and cooling fan assembly.
Service and Repair REPLACEMENT 1. SEPARATE BATTERY NEGATIVE TERMINAL 2. REMOVE AIR CLEANER INLET NO.1 3. DRAIN ENGINE COOLANT 4. REMOVE V-BANK COVER 5. REMOVE INTAKE AIR CONNECTOR PIPE 6. REMOVE ENGINE
Zoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Timing Components» Timing Chain» Service and Repair» Procedures» Timing Chain and Sprockets Replacement Timing Chain and Sprockets Replacement Tools Required
Timing Belt: Service and Repair Timing Belt Replacement
2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Timing Belt Replacement Removal Procedure 1. Remove the front timing belt cover. 2. Rotate the crankshaft
1990 Nissan-Datsun 300ZX V6-2960cc DOHC Turbo (VG30DETT) Service and Repair TIMING BELT REPLACEMENT
1990 Nissan-Datsun 300ZX V6-2960cc DOHC Turbo (VG30DETT) Service and Repair TIMING BELT REPLACEMENT CAUTION: a. Do not bend or twist timing belt. b. After removing timing belt, do not turn crankshaft and
IN-VEHICLE REPAIR. Timing Drive Components. Removal. 3. Disconnect the eight ignition coil electrical connectors.
303-01A-1 IN-VEHICLE REPAIR Timing Drive Components 303-01A-1 Special Tool(s) Compressor, Valve Spring 303-581 (T97T-6565-A) Holding Tool, Crankshaft 303-448 (T93P-6303-A) 3. Disconnect the eight ignition
2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender
IN-VEHICLE REPAIR. Timing Drive Components Camshaft Drive Cassette, LH. Special Tool(s) Holding Tool, Camshaft Sprocket (T97T-6256)
303-01A-1 IN-VEHICLE REPAIR Timing Drive Components Camshaft Drive Cassette, LH 303-01A-1 Special Tool(s) Holding Tool, Camshaft Sprocket 303-564 (T97T-6256) Adapter for 303-564 303-578 (T97T-6256-A) Holding
2. Timing Belt SERVICE PROCEDURE A: REMOVAL 1. CRANKSHAFT PULLEY AND BELT COVER. 1) Remove A/C belt. (With A/C model)
SERVICE PROCEDURE [W2A1] 2-3a A: REMOVAL 1. CRANKSHAFT PULLEY AND BELT COVER B2M2583A (1) Front side V-belt (2) Rear side V-belt (With A/C model) (3) Crankshaft pulley bolt (4) Crankshaft Pulley (5) Belt
2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE)
2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair TIMING CHAIN TIMING CHAIN http://alldatapro.com/alldata/pro~v440713400~c39519~r0~od~n/0/108596970/110859775/110859788/110859790/34853741/100411974/34853743/56492475
REPLACEMENT HINT: 11. REMOVE V RIBBED BELT TENSIONER ASSY (a) Remove the 5 bolts and V ribbed belt tensioner.
14142 REPLACEMENT HINT: ENGINE MECHANICAL Refer to CAMSHAFT (RH BANK) or CAMSHAFT (LH BANK) for the replacement procedure of the No.2 chain (see page 14157 or 14175). 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
3/13/ :32 AM. NOTICE: Do not disconnect the hose.
1 of 25 REPLACEMENT 1. REMOVE HOOD SUB-ASSEMBLY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER RH 5. REMOVE FRONT FENDER APRON SEAL RH 6. DRAIN ENGINE OIL a. Install
1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM WS002X
Last Modified: 4-26-2007 Service Category: Engine/Hybrid System 1.6 A Section: Engine Mechanical Model Year: 2007 Model: 4Runner Doc ID: RM0000029WS002X Title: 1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION
15.Timing Belt Assembly
15.Timing Belt Assembly A: REMOVAL 1. TIMING BELT 1) Remove the V-belt. 2) Remove the crankshaft pulley. 3)
2005 Chrysler 300 C ENGINE Mechanical - 3.5L - Service Information & Magnum
1. Install camshaft sprockets onto the camshafts. Install NEW sprocket attaching bolts into place. The 255 mm (10 in.) bolt is to be installed in the left camshaft and the 213 mm (8 3/8 in.) bolt is to
2003 Saturn Vue. SATURN 3.0L V6 DOHC - L-Series After VIN & Vue
TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. 2. Raise and support vehicle. Remove right front wheel. Remove lower front splash shield. 3. Lower vehicle. Loosen,
1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder
![1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder](/thumbs/95/123571962.jpg "1991 Nissan 240SX. 2.4L 4-CYL - VINS [F,M,S] 1991 ENGINES Nissan 2.4L 4-Cylinder")
NOTE: Use illustration for component reference. See Fig. 7. 1. Remove spark plug wires. Set No. 1 piston at TDC on its compression stroke. Remove vacuum hoses, electrical harnesses, connectors, and harness
2/17/2017 Timing Belt Service and Repair, Removal and Replacement
http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com 1/22 http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com
2002 Escape Workshop Manual
SECTION 303-01B: Engine 3.0L (4V) IN-VEHICLE REPAIR Procedure revision date: 10/09/2003 Timing Drive Components Removal CAUTION: Failure to verify correct timing drive component alignment will result in
2000 Toyota Truck Tundra. Timing Belt: Service and Repair
Timing Belt: Service and Repair REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. REMOVE RADIATOR ASSEMBLY 4. REMOVE THROTTLE BODY COVER 5. REMOVE INTAKE AIR CONNECTOR ASSEMBLY 6. REMOVE
10. SEPARATE COMPRESSOR (a) Remove the nut, 3 bolts compressor stay and compressor. HINT: Hang up the hoses instead of detaching.
14108 ENGINE MECHANICAL REPLACEMENT 1. DRAIN ENGINE COOLANT(See page165 ) 2. SEPARATE BATTERY NEGATIVE TERMINAL 3. REMOVE VBANK COVER SUBASSY (a) Remove the 2 cap nuts and Vbank cover subassy. 4. REMOVE
26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]
![26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]](/thumbs/85/92233007.jpg "26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]")
Last Modified: 8-24-2016 6.6 A Doc ID: RM000000T4X000X Model Year Start: 2006 Model: GS300 Prod Date Range: [01/2005 - ] Title: 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/2005
2001 Dodge Dakota ENGINES 4.7L V8
FRONT COVER Removal & Installation 1. Disconnect negative battery cable. Remove drive belt. Remove A/C compressor mounting bolts, and position compressor aside. Drain cooling system. Remove radiator hoses.
Service and Repair Note:
Service and Repair Note: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure. Timing Drive Components - Timing
CAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.
Installation Engines with ratcheting timing chain tensioners 1. CAUTION: Timing chain procedure must be followed exactly or damage to valves and pistons will result. CAUTION: Do not compress the ratchet
3. Timing Belt 2-3 SERVICE PROCEDURE A: REMOVAL 1. CRANKSHAFT PULLEY AND BELT COVER
SERVICE PROCEDURE 2-3 A: REMOVAL 1. CRANKSHAFT PULLEY AND BELT COVER G2M0107 1) Remove V-belt and A/C belt tensioner. 2) Remove pulley bolt. To lock crankshaft use ST. ST 499977000 CRANKSHAFT PULLEY WRENCH
REPLACEMENT. 1. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 4 nuts and cylinder head cover No. 2.
ENGINE MECHANICAL 1475 REPLACEMENT 141FV01 1. REMOVE CYLINDER HEAD COVER NO.2 (a) Remove the 4 nuts and cylinder head cover No. 2. A66316 2. REMOVE IGNITION COIL NO.1 (a) Remove the 4 bolts and pull out
Timing Belt: Service and Repair Timing Belt Replacement
2000 Cadillac Catera V6-3.0L VIN R Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair Timing Belt Replacement TIMING BELT REPLACEMENT Removal Procedure ^ Tools Required - J 42069 Timing
25. REMOVE OIL PIPE NO.1 (a) Remove the 2 oil pipe unions, and oil pipe No.1. (b) Remove the oil control valve filter LH and gaskets.
CAMSHAFT (RH BANK) (2GRFE) REPLACEMENT 1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE 1421) 2. REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE 1421) 4. REMOVE STARTER ASSY (SEE PAGE 199). REMOVE
1 of 12 11/20/2016 9:32 PM
1 of 12 11/20/2016 9:32 PM Caution: After removing timing chain, do not turn crankshaft and camshaft separately, or valves will strike piston heads. Apply new engine oil to the sliding surfaces when Installing
4. Remove the charge air cooler. (See INTAKE AIR SYSTEM REMOVAL/INSTALLATION [L3 WITH TC].)
![4. Remove the charge air cooler. (See INTAKE AIR SYSTEM REMOVAL/INSTALLATION [L3 WITH TC].)](/thumbs/96/128786582.jpg "4. Remove the charge air cooler. (See INTAKE AIR SYSTEM REMOVAL/INSTALLATION [L3 WITH TC].)")
TIMING CHAIN REMOVAL/INSTALLA... < Previous Next > 2007 Mazda3 Engine TIMING CHAIN REMOVAL/INSTALLATION [L3 WITH TC] 1. Remove the battery cover. 2. Disconnect the negative battery cable. 3. Remove the
1 of 17 2/19/ :10 AM TIMING BELT
1 of 17 2/19/2012 11:10 AM TIMING BELT 2 of 17 2/19/2012 11:10 AM INSTALLATION SPROCKET 1) Install right-hand belt cover No.2. 3 of 17 2/19/2012 11:10 AM 2) Install left-hand belt cover No.2. 3) Install
TIMING CHAIN COMPONENTS
h Page 1 of 52 TIMING CHAIN COMPONENTS ht Page 2 of 52 Fig. 24: Displaying Timing Chain Components (1 Of 2) Page 3 of 52 Fig. 25: Displaying Timing Chain Components (2 Of 2) Page 4 of 52 REMOVAL NOTE:
EG 18 ENGINE MECHANICAL TIMING BELT EG5EK 01 COMPONENTS FOR REMOVAL AND INSTALLATION
EG18 ENGINE TIMING BELT COMPONENTS FOR REMOVAL AND INSTALLATION EG5EK01 ENGINE EG19 EG20 ENGINE ENGINE EG21 EG22 ENGINE TIMING BELT REMOVAL EG5G101 1. REMOVE OIL PAN PROTECTOR 2. REMOVE ENGINE UNDER COVER
CAMSHAFT (LH BANK) (2GR FE) ENGINE MECHANICAL 1424N 01 REPLACEMENT
REPLACEMENT N0. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE ). REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE ). REMOVE STARTER ASSY (SEE PAGE 99). REMOVE AUTOMATIC TRANSAXLE ASSY (SEE PAGE
file://c:\program Files\tsocache\OFFICE_5416\SY1~us~en~file=SY131B46.htm~gen~ref...
Page 1 of 41 SECTION 303-01B: Engine 4.6L and 5.4L 2000 F-150 Workshop Manual ASSEMBLY Procedure revision date: 01/27/2004 Engine 4.6L Special Tool(s) Compressor, Valve Spring 303-567 (T97P-6565-AH) Compressor
Engine. Special Tool(s) Compressor, Valve Spring (T97P-6565-AH) Compressor Spacer, Valve Spring (T91P-6565-AH)
Page 1 of 41 SECTION 303-01A: Engine 5.4L (2V) 2000 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis Workshop Manual ASSEMBLY Procedure revision date: 04/04/2003 Engine Special Tool(s) Compressor,
2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 2 Installation 1. The TDC marks of the intake and exhaust CVVT sprockets are
Timing Belt Replacement
2004 Accord Timing Belt Replacement Report a problem with this article NOTE: The following procedure is for the installation of a new timing belt. If you are installing a used belt, refer to the timing
12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 4 bolts, the engine moving control rod and the bracket.
TIMING BELT (3MZFE) REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FR WIPER ARM RH (See page 669) 3. REMOVE FR WIPER ARM LH (See page 669) 4. REMOVE COWL TOP VENTILATOR LOUVER SUBASSY (See page 669) 5.
Timing Belt: Service and Repair
2000 Hyundai Sonata L4-2.4L Page 1 Timing Belt: Service and Repair REMOVAL 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 2000 Hyundai Sonata
Timing Drive Components Camshaft Timing
SECTION 303-01B: Engine 4.0L SOHC 1998 Explorer/Mountaineer Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/17/2002 Timing Drive Components Camshaft Timing Special Tool(s) Timing Chain Tensioner
Testing and Inspection. Diagnostic Procedure Step 1-2
1 of 4 5/22/2008 7:54 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 2002 Nissan-Datsun Altima 2.5 S L4-2.5L (QR25DE) Vehicle
VALVE CLEARANCE (1NZ-FXE)
146 ENGINE MECHANICAL ADJUSTMENT 1. REMOVE REAR FLOOR BOARD NO.2 (See page 211 16) 2. REMOVE DECK FLOOR BOX REAR (See page 211 16) 3. REMOVE REAR FLOOR BOARD NO.3 (See page 211 16) 4. DISCONNECT BATTERY
Page 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components
Page 1 of 25 Service and Repair REMOVAL Related Components Page 2 of 25 1ZZ-FE Page 3 of 25 2ZZ-GE 1. REMOVE UPPER FRONT FENDER APRON SEAL AND UPPER RADIATOR SUPPORT SEAL 2. DRAIN ENGINE COOLANT 3. REMOVE
Mazda North American Operations Irvine, CA
Service Bulletin Mazda North American Operations Irvine, CA 92618-2922 Subject: VARIABLE VALVE TIMING (VVT) NOISE AND/OR TIMING CHAIN NOISE Bulletin No: 01-012/12 MULTI-MODEL (L3 TURBO) - VARIABLE VALVE
REMOVAL AND INSTALLATION
2006 Eclipse (2.4L 4G69) REMOVAL AND INSTALLATION Report a problem with this article Pre-removal Operation Side Under Cover Removal (Refer to GROUP 51, Under Cover Post-installation Operation Crankshaft
2003 Hyundai Truck Santa Fe V6-3.5L
Page 1 of 12 2003 Hyundai Truck Santa Fe V6-3.5L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair Page 2 of 12 REMOVAL 1. Remove the wheel of passenger side. 2. Remove the
11/29/2017 Engine Cooling - Coolant Pump - Removal and Installation 2010 Ford Edge MotoLogic Engine Cooling 2010 Edge, MKX
2010 Edge Report a problem with this article 303-03 Engine Cooling 2010 Edge, MKX REMOVAL AND INSTALLATION Procedure revision date: 10/04/2010 Coolant Pump Special Tool(s) Camshaft Holding Tool 303-1248
Timing Belt: Service and Repair TIMING BELT
2003 Hyundai Truck Santa Fe V6-2.7L Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair TIMING BELT TIMING BELT 2.7L REMOVAL 1. Remove the engine cover. 2. Using a [16 mm], rotate the
2004 Toyota CAMRY. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS
2004 Toyota CAMRY Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS REPLACEMENT 1. REMOVE HOOD SU-ASSY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER
Camshaft Timing Chain, Sprocket, And Tensioner Replacement
2007 Pontiac Solstice - Engine Mechanical > Engine Mechanical - 2.0L > Repair Instructi... Page 1 of 29 2007 Pontiac Solstice : Engine Mechanical > Engine Mechanical - 2.0L > Repair Instructions - On Vehicle
Service and Repair. Material. Timing chain
ALLDATA Online - 1999 Mercury Cougar V6-153 2.5L DOHC VIN L SFI - Service and... Page 1 of 16 Service and Repair Notes Material Timing chain 1. Remove and discard the camshaft seal. 2. Remove the engine
20.Cylinder Block. Cylinder Block A: REMOVAL ME(H4DOTC)-63 ST CRANKSHAFT STOPPER
Cylinder Block MECHANICAL 20.Cylinder Block A: REMOVAL Before conducting this procedure, drain engine oil completely. 1) Remove the intake manifold. 2)
2007 Ford Freestyle SEL
Fig. 279: Exploded View Of Engine Heads, Intake & Exhaust Components Item Part Number Description 1 9D475 Exhaust gas recirculation (EGR) system module 2 9D477 EGR module tube 3 9F485 RH exhaust manifold
REPLACEMENT. 12. REMOVE ENGINE MOVING CONTROL ROD (a) Remove the 5 bolts, the engine moving control rod and the engine mounting stay.
1484 ENGINE MECHANICAL REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT WIPER ARM HEAD CAP 3. REMOVE FR WIPER ARM RH (See page 668 ) 4. REMOVE FR WIPER ARM LH (See page 668 ) 5. REMOVE COWL TOP VENTILATOR
SECTION C Engine 5.4L (4V)
303-01C-i Engine 5.4L (4V) 303-01C-i SECTION 303-01C Engine 5.4L (4V) CONTENTS PAGE IN-VEHICLE REPAIR Timing Drive Components... 303-01C-2 303-01C-2 Engine 5.4L (4V) 303-01C-2 IN-VEHICLE REPAIR Timing
Classification: Reference: Date: VE30DE CAM TIMING
Classification: Reference: Date: EM93-002 NTB93-126 September 2, 1993 VE30DE CAM TIMING APPLIED VEHICLE(S): All equipped with VE30DE Engine SERVICE INFORMATION When servicing VE30DE engine cylinder heads,
Timing Belt Replacement
Timing Belt Replacement Tools Required Timing Belt Alignment Kit Crank Hub TORX Socket Removal Procedure 1. Disconnect the negative battery cable. 2. Remove the timing belt front cover. 3. Rotate the crankshaft
CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT
Page 1 of 45 CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT Special Tools J 45027 Tensioner Tool J 45059 Angle Meter Page 2 of 45 Removal Procedure Page 3 of 45 Page 4 of 45 Page 5 of 45 Fig.
2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.
TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right
1998 Subaru Forester
Inspection 1. Inspect timing belt teeth for breaks, cracks or wear. Inspect belt for signs of oil contamination. When inspecting timing belt, do not bend less than a radius of 2.36" (6.0 mm). Replace belt
REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH. 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N.
REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE FRONT WHEEL RH 3. REMOVE REAR WHEEL (for 4WD) (a) Move the select lever to N. (b) Check that the parking brake is released. (c) Remove
1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover.
DISASSEMBLY 1. Remove the crankshaft pulley, engine coolant pump pulley and drive belt. 2. Remove the timing belt cover. 3. Turn the crankshaft clockwise and align the timing marks so as to bring the No.
GM 4-Cylinder Cam Tool Set Operating Instructions
GM 4-Cylinder Cam Tool Set Operating Instructions Cam Tool Part No. Page Camshaft Gear Holder... 536174...2 Camshaft Gear Holder... 536176...2 Camshaft Holding Tool... 536172... 14 Camshaft Sprocket Holding
Tech Talk. Timing Belt 6VD1/6VE1
Holden DOHC V6 Frontera 6VD1 3.2L 1999 2004 Jackaroo 6VE1 3.5L 1998 2004 Rodeo TF 6VD1 3.2L 1998 2003 Rodeo RA 6VE1 3.5L 2003 2005 Important: Read through all the instructions before proceeding with the
2. Timing Belt. 2-3b [W2A1] SERVICE PROCEDURE A: REMOVAL 1. CRANKSHAFT PULLEY AND BELT COVER
![2. Timing Belt. 2-3b [W2A1] SERVICE PROCEDURE A: REMOVAL 1. CRANKSHAFT PULLEY AND BELT COVER](/thumbs/76/74262870.jpg "2. Timing Belt. 2-3b [W2A1] SERVICE PROCEDURE A: REMOVAL 1. CRANKSHAFT PULLEY AND BELT COVER")
2-3b [W2A1] SERVICE PROCEDURE A: REMOVAL 1. CRANKSHAFT PULLEY AND BELT COVER B2M1705C (1) V-belt (2) Crankshaft pulley bolt (3) Crankshaft pulley (4) Left-hand belt cover No. 1 (5) Right-hand belt cover
REMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and
2002 Escape Workshop Manual
SECTION 303-01A: Engine 2.0L Zetec 2002 Escape Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/25/2004 Timing Belt Special Tool(s) Crankshaft TDC Timing Peg 303-574 (T97P-6000-A) Camshaft
TIMING BELT (1MZ FE Jan., 2003)
14 100 TIMING BELT (1MZ FE Jan., 2003) REPLACEMENT 1. REMOVE FRONT WHEEL RH 2. REMOVE FRONT FENDER APRON SEAL RH 3. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (See Pub. No. RM972U on page
2002 Explorer Sport/Sport Trac Workshop Manual
Page 1 of 17 SECTION 303-01: Engine 4.0L Single Overhead Camshaft (SOHC) IN-VEHICLE REPAIR Procedure revision date: 07/13/2005 Cylinder Head Special Tool(s) Spark Plug Wire Remover 303-106 (T74P-6666-A)
Recommended Installation Procedure (11 DEC 09) ATech Timing Belt Tensioner (979847/901) VW 1.6/2.0L L4 EA189 CR Engine
Initial Preparation: Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to VW s guidelines. The mounting of the TBT is done on the
ENGINE MECHANICAL <3.8L ENGINE>
11A-1 GROUP 11A ENGINE MECHANICAL CONTENTS GENERAL DESCRIPTION 11A-2 ENGINE DIAGNOSIS 11A-3 SPECIAL TOOLS 11A-4 ON-VEHICLE SERVICE 11A-8 DRIVE BELT TENSION CHECK AND ADJUSTMENT 11A-8 IGNITION
Timing Belt: Service and Repair Removal and Installation Removal
2004 Acura Truck MDX V6-3471cc 3.5L Copyright 2009, ALLDATA 10.10 Page 1 Timing Belt: Service and Repair Removal and Installation Removal 1. Turn the crankshaft so its white mark (A) lines up with the
Timing Chain: Service and Repair
1996 Nissan-Datsun Truck D21 Hardbody 2WD L4-2389cc 2.4L SOHC MFI (KA24E) Copyright 2013, ALLDATA 10.52 Page 1 Timing Chain: Service and Repair *** THIS ARTICLE INCLUDES UPDATES MADE BY TSB 95027, DATED
IN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent
303-01A-1 IN-VEHICLE REPAIR Cylinder Head Special Tool(s) Torque Wrench Extension 303-575 (T97T-6256-F) or equivalent Special Tool(s) 303-01A-1 Timing Tool, Crankshaft TDC 303-573 (T97T-6303-A) or equivalent
TECHNICAL SERVICE BULLETIN
TECHNICAL SERVICE BULLETIN SUBJECT: NO.: 09-15-93 Camshaft Timing Belt Replacement/Adjustment GROUP: Engine Service Procedure DATE: Sep.17, 1993 This Bulletin Is Supplied As Technical Information Only
TIMING BELT COMPONENTS EM 15
ENGINE MECHANICAL COMPONENTS EM15 EM16 ENGINE MECHANICAL COMPONENTS (Cont d) ENGINE MECHANICAL EM17 REMOVAL OF (See pages EM15 and 16) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work
CAMSHAFT TIMING CHAIN, SPROCK... CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT (LE5 OR LE9) (ENGINE MECHANICAL - 2.2L OR 2.
CAMSHAFT TIMING CHAIN, SPROCK... CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT (LE5 OR LE9) (ENGINE MECHANICAL - 2.2L OR 2.4L) Document ID# 2133175 Camshaft Timing Chain, Sprocket, and Tensioner
2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 1
2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair Timing Belt REMOVAL 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove
1 of 10 2/10/2017 5:20 PM
1 of 10 2/10/2017 5:20 PM Crankshaft Pulley Removal NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure. The crankshaft
TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT
TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove right front wheel. 3. Remove belt splash shield. 4. Remove accessory drive belts.
1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers..
BELT AND SPROCKETS-TIMING REMOVAL TIMING BELT Zoom 1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers.. CAUTION: When aligning crankshaft and camshaft timing marks
ENGINE REMOVAL Install: Exhaust pipe 1 5. Tighten: Nuts (exhaust pipe) 2. Exhaust pipe nut 20 Nm (2.0 m kgf, 14 ft lbf) 6.
ENGINE REMOVAL 4. Install: Gasket New Exhaust pipe 1 5. Tighten: Nuts (exhaust pipe) 2 Exhaust pipe nut 20 Nm (2.0 m kgf, 14 ft lbf) 6. Install: Clamp Slide the clamp onto the end of the muffler and insert
2001 LEGACY SERVICE MANUAL QUICK REFERENCE INDEX
2001 LEGAY SERVIE MANUAL QUIK REFERENE INDEX SUPPLEMENT FOR 6 YLINDER ENGINE MODEL This service manual has been prepared to provide SUARU service personnel with the necessary information and data for the
1996 Isuzu Truck Rodeo (2WD) V6-3165cc 3.2L SOHC (6VD1)
1996 Isuzu Truck Rodeo (2WD) V6-3165cc 3.2L SOHC (6VD1) Service and Repair Notes REMOVAL STEPS Preparation: Battery ground cable 1. Radiator upper fan shroud Remove from radiator. 2. Cooling fan assembly
Service and Repair. Removal. Remove the engine cover. Remove the drive belt. Select Vehicle New TSBs Technician's Reference
1 of 7 4/5/2008 9:30 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 2002 Kia Truck Sedona EX V6-3.5L Vehicle Level Engine,
11. REMOVE OIL PAN SUB ASSY NO.2 (a) Remove the 18 bolts and 2 nuts.
1444 ENGINE MECHANICAL REPLACEMENT 1. REMOVE ENGINE ASSEMBLY (SEE PAGE 1419) 2. REMOVE DRIVE PLATE & RING GEAR SUBASSY (AUTOMATIC TRANSMISSION) (SEE PAGE 1419) SST 0921354015 (9165160855), 0933000021 3.
TIMING BELT REMOVAL - TIMING BELT
2004 Chrysler Concorde V6-3.5L VIN M Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair > Procedures TIMING BELT REMOVAL - TIMING BELT CAUTION: The following
2001 Toyota MR ENGINES' '1.8L 4-Cylinder
TIMING CHAIN Removal 1. Disconnect negative battery cable. Drain cooling system. On Corolla, remove windshield washer fluid reservoir. On Celica, remove upper front fender apron seal and upper radiator