ov-lifting_bolts_divider - Updated Lifting Bolts

Size: px
Start display at page:

Download "ov-lifting_bolts_divider - Updated Lifting Bolts"

Transcription

1 ov-lifting_bolts_divider - Updated Lifting Bolts

2 Technical Information roduct information Lifting Bolts roduct marking Compliant with 2006/42/EC, and with individual date of manufacture and batch number. Complies with 2006/42/CE Model No. Individual part no. date of manufacture Lifting angles Load 100% of load rating of bolt 45 Steel and Stainless steel (316) versions Load Approx 66% of load rating of bolt 60 Load Approx 50% of load rating of bolt For full information on lifting arrangements see technical pages Steel CE mark WLL weight limit Stainless (316L) Lifting Bolts from Automotion Components ov-lifting_bolts_product_information - Updated Tel: Fax: web: mechanicalcomponents.co.uk a website from Automotion Components 743

3 Lifting Bolts Technical Information Installation information ov-lifting_bolts_installation_information - Updated Lifting Bolts from Automotion Components Never use an oversized hook or other lifting device which will pry or tend to open the U shaped bar on centre pull hoist rings. After installation, check the hoist ring to be sure it swivels and pivots freely in all directions. The side of the ring must not contact anything. Always ensure full thread engagement when installing hoist rings. 744 Tel: Fax: web: mechanicalcomponents.co.uk a website from Automotion Components

4 Introduction Swivel Lifting Rings and Lifting Bolts Lifting Bolts Introduction to swivel lifting rings and Lifting Bolts ( ) Our swivel lifting rings fully comply with the EC directive 2006/42/EC. They are CE marked and are supplied with a Certifi cate of Conformity. There is a 100% check on anti-cracking, a proof load test of 2.5 x load limit and a safety factor of 5 on most parts. Each ring is individually marked to ensure full product traceability. The Swivel Lifting Rings come in three main forms depending on the number of axis required to swivel. The most popular type is the double swivel rings. Single swivel Threads M8 M48 Loads 0,3 tons to 15 tons Double swivel Threads M4 M100 Loads 0,05 tons to 50 tons Triple swivel Threads M8 M56 Loads 0,3 tons to 22 tons Swivel lifting rings operating instructions. lease follow these instructions carefully. Ensure all lifting bolts are CE marked. Ensure they are handled by qualifi ed personnel. Refer to the operating instructions particularly with regards to product selection, any possibility of the load swivelling, the effect of lifting angles on the load capacity (see relevant tables), etc. Never allow any personnel underneath a suspended load. Always heed the load rating of the lifting bolt. Always perform a visual inspection of the lifting rings prior to use. Checking for any damage to thread and/or swivelling system. Check for wear or corrosion, signs of stress or bending. Check CE mark and load rating. Ensure a yearly full service inspection is performed. Always ensure the full bottom face of the lifting bolts is in contact with a smooth, square surface. Ensure bolt is tightened to the correct torque. Ensure full and unrestricted movement of the lifting ring in all directions. Before each lift ensure the correct orientation of the shackle in the lift direction. Avoid using our standard steel lifting rings in corrosive environments eg sandy, chemical, acid, moisture etc. In this case consider using our stainless steel lifting rings. Note the thread length requirements: - 1 x thread diameter for steel (ST37 min.) x thread diameter for cast iron. - 2 x thread diameter for aluminium x thread diameter for other light metals. - If fi xing into low resistance material it is better to allow for a bigger diameter thread to compensate for the lower material resistance. Note: The full thread must be engaged. Longer thread lengths can be supplied on request or a bolt and washer/nut combination can be used. REORT OF THOROUGH EXAMINATION This report complies with the requirements of the Lifting Operations and Lifting Equipment Regulations 1998 Date of Thorough Examination: Sales Order number: Name and Address of customer for whom the thorough examination was made: Automotion Components Ltd Alexia House Description and identification of the equipment, including type, dimension and part number: Little Mead Industrial Estate Cranleigh Surrey GU6 8NE Quantity: Working Load Limit: in conjunction with this document. Original declaration of conformity is available on request Date of manufacture if known: Material: Was the examination carried out in accordance with an examination scheme: Batch : This part is CE marked in compliance with European Directive : Identification of any part found to have a defect which is or could become a danger to persons and a description of the defect: (If none state NONE) None. 2006/42/EC. YES NO articulars of any repair, renewal or alteration required to remedy the defect identified above: Is the above an existing or imminent danger to persons *Note-This is a reportable defect YES NO SECIMEN articulars of any tests carried out as part of the examination: (If none state NONE) Visual inspection and compliance. IS THIS EQUIMENT SAFE TO OERATE? YES NO Name of person making this report: Name of person authenticating this report: Latest date by which n N/A ov-lifting_bolts_rings_and_bolts - Updated Tel: Fax: web: mechanicalcomponents.co.uk a website from Automotion Components

5 Swivel Lifting Rings Safety Guide

6 Single swivel Threads M8 M48 Loads 0,3 tons to 15 tons Double swivel Threads M4 M100 Loads 0,05 tons to 50 tons Triple swivel Threads M8 M56 Loads 0,3 tons to 22 tons SECIMEN

7 4020 Threads M8 M30 Loads 0,3 tons to 3 tons Threads M30 M45 Loads 3,5 tons to 6 tons. Complies with 2006/42/CE CE mark Model No. WLL weight limit Individual part no. date of manufacture Never use an oversized hook or other lifting device which will pry or tend to open the U shaped bar on center pull hoist rings. Load Load Load 100% of load rating of bolt Approx 66% of load rating of bolt Approx 50% of load rating of bolt For full information on lifting arrangements see technical pages After installation, check the hoist ring to be sure it swivels and pivots freely in all directions. The side of the ring must not contact anything. Steel Stainless (316L) Always ensure full thread engagement when installing hoist rings. Also ensure face is flush.

8 α α

9

10 α α

11

12 α α

13

14 α α

15

16

17 Lifting Bolts Safety Guide

18 Standard Lifting Bolts Standard lifting bolts (to DIN 580 and DIN 582) ( ) These are CE marked and are available with male or female threads in either steel or stainless steel (A4 AISI 316). They are meant only for use at a maximum angle of 45 from the thread. They are not meant for loads that might swivel. These are supplied with a generic Declaration of Conformity (DOC) stating that the parts have been manufactured to the relevant DIN standard and therefore suitable for lifting. Lifting Bolts Safety Overview 45 Do not lift Assembly instructions The lifting bolts are generally intended for permanent mounting to components such as motors, switchgear cabinets and gears, and for transporting these items of equipment 1. They must be used by qualifi ed personnel trained to current European Standards on the place of use. Lifting bolts must be permanently marked with a raised manufacturer s mark, material ID (e.g. C15E, A2 or A4), load-bearing capacity in axial direction (WLL in Kg), and with the CE symbol. Refer to the relevant table to determine the effect of lifting angles on the load capacity. 2. Check the fi xing points to ensure correct bolt seating, check for; corrosion, wear and tear, deformation etc. at regular intervals and before each use. 3. The fi xing point should be selected carefully such that the resultant forces are absorbed by the base material without any deformation. Screw-in depth for steel with a tensile strength of Rm >340 N/ mm², e.g. S235JR (1.0037); or GG 25 ( without cavities or shrinkage): 1.5 x thread diameter (=L). For screw-in material with lower strength, use fi xing points with greater screw-in length. Minimum screw-in depths recommended by the Liability Insurance Association: 2 x thread diameter in aluminum alloys 2.5 x thread diameter in light metal with low strength For light metals, non-ferrous metals and grey cast iron, select the thread such that the load-bearing capacity of the thread corresponds with the requirements involving the base material. For through-holes, a nut (0.8 x d) should be fully and fi rmly bolted from the opposite side. If the thread length of the screw is suffi cient, the use of an additional washer is recommended. 4. Select the location of fi xing points carefully to ensure that any rotational effects or load shifts are avoided. Arrange the fi xing point for a single strand sling perpendicularly above the center of the load. Arrange the fi xing points for a twin strand sling on both sides and above the load center. Caution: Avoid turning or rotating movements during the lift! osition the lifting bolt such that no shear tension acts on the bolt. Any introduced force must act in the direction of the eye bolt plane. Standard lifting bolts DIN 580 & DIN The attachment surface must be fl at. Maximum spot-facing of the thread hole = nominal diameter of the thread. Blind holes must be drilled to a suffi cient depth to ensure that the contact surface of the eye bolt is fully seated. 6. Shock loads, tugs or vibrations may cause inadvertent loosening. Consider using a liquid thread lock agent such as Loctite making sure to observe the manufacturer s recommendations. Always secure bolts which remain permanently at the fi xing point, e.g. by glueing. 7. The end attachment must be freely moveable in the lifting bolt. When slinging and removing the end attachments (sling chain, round sling, wire rope), make sure that no pinch, shear, catch or impact points occur. Avoid damage to the end attachments caused by sharpedged loads. 8. Temperature suitability: these lifting bolts may be used without restricting or impairing the load-bearing capacity within the temperature range from -20 C to +200 C. 9. The seating surface of the bolts must not be allowed to make contact with corrosive chemicals, acids or their vapours. 10. After initial installation and at intervals depending on use, however at least once every year, the continued suitability of the fi xing point must be checked and inspected by an expert. This should also be done after any damage or other unusual incidents. If there is any doubt with regard to safe use, the fi xing point and/or the lifting equipment must not be used for safety reasons. No person should operate under a suspended load and operators should not be distracted or put in danger in the handling area. Failure to observe these instructions may result in personal injury and material damage! F 1 F

19 F 1 Max. Kg F 2 Max. Kg F 1 Max. Kg F 2 Max. Kg F 1 Max. Kg F 2 Max. Kg M / M / M / M / M / M / M / M M / M / M / M / F 1 Max. Kg F 2 Max. Kg M M M M M M M M M72 x M80 x M100 x * F 1 Max. Kg F 2 Max. Kg F 1 Max. Kg F 2 Max. Kg / / *For UNC, BS & BSW threads.

20 Auto 0496 Web: Tel.: Fax: Due diligence has been taken in preparing these safety instructions. Automotion Components Ltd can not be held legally responsible nor liable for any missing or incorrect information and the ensuing consequences. Automotion Components Ltd reserves the right, without prior notice to effect modifi cations and design changes to these products and associated documentation as part of a continuous program of product development.

21 Steel Male Lifting Eye Bolts metric sizes Lifting Bolts & Shackles 4040 Material Forged steel (C15E) annealed and zinc plated. Contact face machined. CE marked. Hot dipped galvanised versions (for more demanding applications and limited outside use) also available on request, suffix changes to -GV. Technical notes To DIN 580. When using lifting eye bolts it is critical to ensure that the face is in firm contact with the mating surface. These lifting bolts are generally installed and remain on a piece of equipment for the purpose of transporting them. They are not for repeated lifting use - if this is required our swivelling lifting bolt range should be used. Tips Maximum load values are only applicable when the thread is fully screwed in, and the material it is being used in is as least as strong as the that of the bolt. Temperature range -20 C to +200 C. F 1 and F 2 values given are for steel and cast iron components. Important notes Not to be used at lift angles of greater than 45 or with swivelling loads. lease refer to the safety documentation before using this part. Supplied with certificate and operating instructions. Order No. Thread d 1 h w 1 d 2 w 2 w 3 F 1 max. Kg F 2 max. Kg X Kg l Z Coarse M ,05 13, Z Coarse M ,06 13, Z Coarse M ,11 17, Z Coarse M ,18 20, Z Coarse M ,18 27, Z Coarse M ,28 27, Z Coarse M ,43 30, Z Coarse M ,45 30, Z Coarse M ,45 30, Z Coarse M ,74 36, Z Coarse M ,93 45, Z Coarse M ,66 45, Z Coarse M ,60 54, Z Coarse M ,65 54, Z Coarse M ,87 63, Z Coarse M ,03 63, Z Coarse M ,15 68, Z Coarse M ,38 68, Z Coarse M ,80 78, Z Coarse M ,4 90, Z Coarse M72 x ,3 100, Z Coarse M80 x ,2 112, Z Coarse M100 x ,1 130,0 Tel: Fax: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk

22 Steel Male Lifting Eye Bolts metric sizes Lifting Bolts & Shackles Order No. Thread d 1 h w 1 d 2 w 2 w 3 F 1 max. Kg F 2 max. Kg X Kg l Z Fine M12 x 1, ,18 20, Z Fine M16 x 1, ,28 27, Z Fine M20 x 2, ,45 30, Z Fine M24 x 2, ,74 36, Z Fine M30 x 2, ,66 45, Z Fine M36 x 3, ,58 54, Z Fine M42 x 3, ,95 63, Z Fine M48 x 3, ,38 68, Z Fine M56 x 4, ,48 78,0 Tel: Fax: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk

23 Steel Female Lifting Eye Bolts metric sizes Lifting Bolts & Shackles 4041 Material Forged steel (C15E) annealed and zinc plated. Contact face machined. CE marked. Hot dipped galvanised versions (for more demanding applications and limited outside use) also available on request, suffix changes to -GV. Technical notes To DIN 582. When using lifting eye bolts it is critical to ensure that the face is in firm contact with the mating surface. These lifting bolts are generally installed and remain on a piece of equipment for the purpose of transporting them. They are not for repeated lifting use - if this is required our swivelling lifting bolt range should be used. Tips Maximum load values are only applicable when the thread and the material, it is being used in is as least as strong as the that of the bolt. Temperature range -20 C to +200 C. F 1 and F 2 values given are for steel and cast iron components. Important notes Not to be used at lift angles of greater than 45 or with swivelling loads. lease refer to the safety documentation before using this part. Supplied with certificate and operating instructions. Order No. Thread d 1 h w 1 d 2 w 2 w 3 F 1 max. Kg F 2 max. Kg X Kg Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M , Z Coarse M72x , Z Coarse M80x , Z Coarse M100x ,4 Tel: Fax: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk

24 Steel Female Lifting Eye Bolts metric sizes Lifting Bolts & Shackles Order No. Thread d 1 h w 1 d 2 w 2 w 3 F 1 max. Kg F 2 max. Kg X Kg Z Fine M16 x 1, , Z Fine M20 x 2, , Z Fine M24 x 2, , Z Fine M30 x 2, , Z Fine M36 x 3, , Z Fine M42 x 3, , Z Fine M48 x 3, , Z Fine M56 x 4, ,69 Tel: Fax: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk

25 Stainless Male Lifting Eye Bolts metric sizes Lifting Bolts & Shackles 4043 Material Stainless steel (A4, AISI 316). CE marked. Technical notes To DIN 580. When using lifting eye bolts it is critical to ensure that the face is in firm contact with the mating surface. These lifting bolts are generally installed and remain on a piece of equipment for the purpose of transporting them. They are not for repeated lifting use - if this is required our swivelling lifting bolt range should be used. Tips Maximum load values are only applicable when the thread and the material, it is being used in is as least as strong as the that of the bolt. F 1 and F 2 values given are for steel and cast iron components. Important notes Not to be used at lift angles of greater than 45 or with swivelling loads. lease refer to the safety documentation before using this part. Supplied with certificate and operating instructions. Order No. Material d 1 l h w 1 d 2 w 2 w 3 F 1 max. Kg F 2 max. Kg X Kg A4 A4 s/s M 6 13, , A4 A4 s/s M 8 13, , A4 A4 s/s M10 17, , A4 A4 s/s M12 20, , A4 A4 s/s M16 27, , A4 A4 s/s M20 30, , A4 A4 s/s M24 36, , A4 A4 s/s M30 45, , A4 A4 s/s M36 54, , A4 A4 s/s M42 63, , A4 A4 s/s M48 68, , A2 A2 s/s M 6 11, , A2 A2 s/s M 8 13, , A2 A2 s/s M10 17, , A2 A2 s/s M12 20, , A2 A2 s/s M16 27, , A2 A2 s/s M20 30, , A2 A2 s/s M24 36, , A2 A2 s/s M30 45, ,66 Tel: Fax: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk

26 Stainless Female Lifting Eye Bolts metric sizes Lifting Bolts & Shackles 4044 Material Stainless steel (A4, AISI 316). CE marked. Technical notes To DIN 582. When using lifting eye bolts it is critical to ensure that the face is in firm contact with the mating surface. These lifting bolts are generally installed and remain on a piece of equipment for the purpose of transporting them. They are not for repeated lifting use - if this is required our swivelling lifting bolt range should be used. Tips Maximum load values are only applicable when the thread and the material, it is being used in is as least as strong as the that of the bolt. F 1 and F 2 values given are for steel and cast iron components. Important notes Not to be used at lift angles of greater than 45 or with swivelling loads. lease refer to the safety documentation before using this part. Supplied with certificate and operating instructions. Order No. Material d 1 h w 1 d 2 w 2 W 3 F 1 max. Kg F 2 max. Kg X Kg A4 A4 s/s M , A4 A4 s/s M , A4 A4 s/s M , A4 A4 s/s M , A4 A4 s/s M , A4 A4 s/s M , A4 A4 s/s M , A4 A4 s/s M @ , A4 A4 s/s M , A4 A4 s/s M , A4 A4 s/s M , A2 A2 s/s M ,5@ , A2 A2 s/s M , , A2 A2 s/s M , A2 A2 s/s M , A2 A2 s/s M , A2 A2 s/s M , A2 A2 s/s M , A2 A2 s/s M , A2 A2 s/s M ,08 Tel: Fax: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk

27 Steel Male Lifting Eye Bolts inch sizes Lifting Bolts & Shackles 4046 Material Forged steel (C15E) annealed and zinc-plated (-Z). Contact face machined. CE marked. Hot dipped galvanised versions (for more demanding applications and limited outside use) also available on request, suffix changes to -GV. Technical notes To DIN 580. When using lifting eye bolts it is critical to ensure that the face is in firm contact with the mating surface. These lifting bolts are generally installed and remain on a piece of equipment for the purpose of transporting them. They are not for repeated lifting use - if this is required our swivelling lifting bolt range should be used. Tips Maximum load values are only applicable when the thread and the material, it is being used in is as least as strong as the that of the bolt. F 1 and F 2 values given are for steel and cast iron components. Important notes Not to be used at lift angles of greater than 45 or with swivelling loads. lease refer to the safety documentation before using this part. Supplied with certificate and operating instructions. Order No. d 1 Thread type d 2 w 1 w 2 w 3 l 1 h F 1max. Kg F 2max. Kg X Kg 4046.U1/4-Z 1/4$-20 UNC , , U5/16-Z 5/16$-18 UNC , , U3/8-Z 3/8$-16 UNC , , U1/2-Z 1/2$-12 UNC , , U5/8-Z 5/8$-11 UNC , , U3/4-Z 3/4$-10 UNC , , U7/8-Z 7/8$-9 UNC , , U1-Z 1$-8 UNC , , U1-1/8-Z 1-1/8$-7 UNC , , U1-1/4-Z 1-1/4$-7 UNC , , U1-1/2-Z 1-1/2$-6 UNC , , U1-3/4-Z 1-3/4$-5 UNC , , U2-Z 2$ UNC , , U2-1/4-Z 2-1/4$ UNC , , U2-1/2-Z 2-1/2$ UNC , , G1/4-Z 1/4$-19 BS , , G3/8-Z 3/8$-19 BS , , G1/2-Z 1/2$-14 BS , , G5/8-Z 5/8$-14 BS , , G3/4-Z 3/4$-14 BS , , G7/8-Z 7/8$-14 BS , ,66 Tel: Fax: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk

28 Steel Male Lifting Eye Bolts inch sizes Lifting Bolts & Shackles Order No. d 1 Thread type d 2 w 1 w 2 w 3 l 1 h F 1max. Kg F 2max. Kg X Kg 4046.G1-Z 1$-11 BS , , G1-1/8-Z 1-1/8$-11 BS , , G1-1/4-Z 1-1/4$-11 BS , ,03@ 4046.G1-1/2-Z 1-1/2$-11 BS , ,38@ 4046.G1-3/4-Z 1-3/4$-11 BS , , G2-Z 2$ BS , , W1/4-Z 1/4$-20 BSW , , W5/16-Z 5/16$-18 BSW , , W3/8-Z 3/8$-16 BSW , , W1/2-Z 1/2$-12 BSW , , W5/8-Z 5/8$-11 BSW , , W3/4-Z 3/4$-10 BSW , , W7/8-Z 7/8$-9 BSW , , W1-Z 1$-8 BSW , , W1-1/8-Z 1-1/8$-7 BSW , , W1-1/4-Z 1-1/4$-7 BSW , , W1-1/2-Z 1-1/2$-6 BSW , , W1-3/4-Z 1-3/4$-5 BSW , , W2-Z 2$ BSW , , W2-1/4-Z 2-1/4$ BSW , , W2-1/2-Z 2-1/2$ BSW , ,40 Tel: Fax: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk

29 Steel Female Lifting Eye Bolts inch sizes Lifting Bolts & Shackles 4048 Material Forged steel (C15E) annealed and zinc plated. Contact face machined. CE marked. Hot dipped galvanised versions (for more demanding applications and limited outside use) also available on request, suffix changes to -GV. Technical notes To DIN 582. When using lifting eye bolts it is critical to ensure that the face is in firm contact with the mating surface. These lifting bolts are generally installed and remain on a piece of equipment for the purpose of transporting them. They are not for repeated lifting use - if this is required our swivelling lifting bolt range should be used. Tips Maximum load values are only applicable when the thread and the material, it is being used in is as least as strong as the that of the bolt. F 1 and F 2 values given are for steel and cast iron components. Important notes Not to be used at lift angles of greater than 45 or with swivelling loads. lease refer to the safety documentation before using this part. Supplied with certificate and operating instructions. Order No. d 1 Thread type d 2 w 1 w 2 h k F 1max. Kg F 2max. Kg X Kg 4048.U1/4-Z 1/4$-20 UNC , U5/16-Z 5/16$-18 UNC , U3/8-Z 3/8$-16 UNC , U1/2-Z 1/2$-13 UNC , U5/8-Z 5/8$-11 UNC , U3/4-Z 3/4$-10 UNC , U7/8-Z 7/8$-9 UNC , U1-Z 1$-8 UNC , U1-1/8-Z 1-1/8$-7 UNC , U1-1/4-Z 1-1/4$-7 UNC , U1-1/2-Z 1-1/2$-6 UNC , U1-3/4-Z 1-3/4$-5 UNC , U2-Z 2$ UNC , U2-1/4-Z 2-1/4$ UNC , U2-1/2-Z 2-1/2$ UNC , G1/4-Z 1/4$-19 BS , G3/8-Z 3/8$-19 BS , G1/2-Z 1/2$-14 BS , G5/8-Z 5/8$-14 BS , G3/4-Z 3/4$-14 BS , G7/8-Z 7/8$-14 BS , G1-Z 1$-11 BS ,32 Tel: Fax: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk

30 Steel Female Lifting Eye Bolts inch sizes Lifting Bolts & Shackles Order No. d 1 Thread type d 2 w 1 w 2 h k F 1max. Kg F 2max. Kg X Kg 4048.W1/4-Z 1/4$-20 BSW , W5/16-Z 5/16$-18 BSW , W3/8-Z 3/8$-16 BSW , W1/2-Z 1/2$-13 BSW , W5/8-Z 5/8$-11 BSW , W3/4-Z 3/4$-10 BSW , W7/8-Z 7/8$-9 BSW , W1-Z 1$-8 BSW , W1-1/8-Z 1-1/8$-7 BSW , W1-1/4-Z 1-1/4$-7 BSW , W1-1/2-Z 1-1/2$-6 BSW , W1-3/4-Z 1-3/4$-5 BSW , W2-Z 2$ BSW , W2-1/4-Z 2-1/4$ BSW , W2-1/2-Z 2-1/2$ BSW ,30 Tel: Fax: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk

31 Clamping Nuts Lifting Bolts & Shackles 4180 Material Steel (C35N) zinc plated, or stainless steel (AISI 316, ). Technical notes To DIN Order No. Material d 1 d 2 d 3 w l 1 l 2 l 3 X Kg Steel M , Steel M , Steel M , Steel M , Steel M , Steel M , A4 Stainless M , A4 Stainless M , A4 Stainless M , A4 Stainless M , A4 Stainless M , A4 Stainless M ,00 50 Tel: Fax: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk

32 Clamping Levers Lifting Bolts & Shackles 4182 Material Steel (St. 37) zinc plated, or stainless steel (A2, AISI 303 or A4 AISI 316). Order No. Material d l Steel M 8 0, Steel M10 0, Steel M12 0, Steel M16 0, Steel M20 0, A2 A2 Stainless M 8 0, A2 A2 Stainless M10 0, A2 A2 Stainless M12 0, A2 A2 Stainless M16 0, A2 A2 Stainless M20 0, X Kg A4 A4 Stainless M 8 0, A4 A4 Stainless M10 0, A4 A4 Stainless M12 0, A4 A4 Stainless M16 0, A4 A4 Stainless M20 0, Tel: Fax: info@automotioncomponents.co.uk Web: automotioncomponents.co.uk

ov-lifting_bolts_divider - Updated Lifting Bolts

ov-lifting_bolts_divider - Updated Lifting Bolts ov-lifting_bolts_divider - Updated - 09-01-2017 Lifting Bolts Technical Information roduct information Lifting Bolts roduct marking Compliant with 2006/42/EC, and with individual date of manufacture and

More information

but this affects the load rating - please ask for more information. Please refer to our technical information pages when specifying and/or using.

but this affects the load rating - please ask for more information. Please refer to our technical information pages when specifying and/or using. Double Swivel Shackle Nuts female Lifting Bolts & Shackles 4010 Material High tensile steel, strength class >8. Supplied with CE certificate. Technical notes Designed to be used directly with the hook

More information

Swivel Lifting Rings - Double Swivel - Male metric - coarse and UNC

Swivel Lifting Rings - Double Swivel - Male metric - coarse and UNC Swivel Lifting Rings Double Swivel Male metric coarse and UNC 63050 Order No. Max. load tons (lbs) d 1 tol. 6H (tol. 2B) l w 1 h 1 h 2 h 3 h 4 h 5 d 2 w 2 a/f 1 a/f 2 Sa fet Torque y to Nm fac (ft lbs)

More information

Swivel Lifting Rings - Double Swivel - Female metric - course and UNC

Swivel Lifting Rings - Double Swivel - Female metric - course and UNC Swivel Lifting Rings Double Swivel Female metric course and UNC 63084 Material High tensile steel, strength class >8. Supplied with CE certificate. Order No. Max. load tons (lbs) d 1 tol. 6g (tol. 2A)

More information

INSTRUCTIONS FOR USE CAUTIONS AND WARNINGS

INSTRUCTIONS FOR USE CAUTIONS AND WARNINGS SECTION 3 General INSTRUCTIONS FOR USE CAUTIONS AND WARNINGS Commercial shackles are not to be used for lifting purposes. Should extreme circumstances or shock loadings be applicable, this must be taken

More information

Bolt-on Swivel Load Rings with Link - RUD VLBG with optional bolt lengths.

Bolt-on Swivel Load Rings with Link - RUD VLBG with optional bolt lengths. 1 of 5 11/03/2015 11:15 (/) RUD "VLBG" Bolt-on Swivel Hoisting Rings, Rotating Swivel Eye Bolts. Metric & Imperial Thread - Range from 300kg to 20,000kg Model: RUD VLBG / BSLR-56 Quick Ref: BSLR-56 Bolt-on

More information

Engineer The Lift!! HOIST RINGS. Applied Load Changes With Sling Angle. Sample Calculation: DO S DON TS

Engineer The Lift!! HOIST RINGS. Applied Load Changes With Sling Angle. Sample Calculation: DO S DON TS H&O DIE SUPPLY, INC. 1-800-222-5441 sales@hodie.com HOIST RINGS 10 Adjustable Alloy Chain Sling... 10.16 Center Pull Style... 10.4-10.5 Envirolox Protective Finish... 10.11 Eye Bolts... 10.15 Eye Nuts...

More information

Operating Manual TWN 0121/1. Lifting point, screw-type TWN 0122 TWN 0123 TWN 0127 TWN 1120 TWN 1830 TWN 1890

Operating Manual TWN 0121/1. Lifting point, screw-type TWN 0122 TWN 0123 TWN 0127 TWN 1120 TWN 1830 TWN 1890 TWN 0121/1 Operating Manual Lifting point, screw-type TWN 0122 TWN 0123 TWN 0127 TWN 1120 TWN 1830 TWN 1890 THIELE GmbH & Co. KG Werkstraße 3 Tel: +49 (0)2371 / 947-0 58640 Iserlohn www.thiele.de B07905-D

More information

Safety is our first priority TM

Safety is our first priority TM Safety is our first priority T Catalog No. -2013.YP1 2 3 T YOKE Yellow Point Series NEVER EXCEED PUBLISHED WORKING LOAD LIIT 4 Worldwide Quality Type Approval And Certificate: 5 NEVER EXCEED PUBLISHED

More information

>VLBG< Load Ring for bolting

>VLBG< Load Ring for bolting RUD-Art.-Nr.: 8500972-EN / 03.013 Load Ring for bolting >< EN Safety instructions This safety instruction/declaration of the manufacturer has to be kept on file for the whole lifetime of the product. Translation

More information

Load Ring for bolting >VLBG<

Load Ring for bolting >VLBG< RUD-Art.-Nr.: 8500972-EN / 05.015 Load Ring for bolting >< EN Safety instructions This safety instruction/declaration of the manufacturer has to be kept on file for the whole lifetime of the product. Translation

More information

Lifting Points Rotating Ball-bearing De-centered Weldable Screw-on

Lifting Points Rotating Ball-bearing De-centered Weldable Screw-on ifting Points Rotating Ball-bearing De-centered Weldable Screw-on ifting Points ifting Points Information 3:2 Rotating Eye ifting Point - REP 3:4 Rotating ifting Point - RP 3:5 Decentered ifting Point

More information

Yellow Point. Catalog No YP.1

Yellow Point. Catalog No YP.1 Yellow Point Catalog No. -2014.YP.1 2 3 T YOKE Yellow Point Series NEVER EXCEED PUBLISHED WORKING LOAD LIIT 4 Worldwide Quality Type Approval And Certificate: 5 NEVER EXCEED PUBLISHED WORKING LOAD LIIT

More information

Yellow Point. Catalog No YP.2

Yellow Point. Catalog No YP.2 Yellow Point Catalog No. 8-15.YP.2 2 3 T YOKE Yellow Point Series NEVER EXCEED PUBLISHED WORKING LOAD LIIT 4 Worldwide Quality Type Approval And Certificate: 5 NEVER EXCEED PUBLISHED WORKING LOAD LIIT

More information

Adjustable Speaker Mount GRAVIS 8

Adjustable Speaker Mount GRAVIS 8 Adjustable Speaker Mount GRAVIS 8 User's Manual Translation of the original instructions Important Information, Please Read Before Use! KLING & FREITAG GmbH Junkersstraße 14 D-30179 Hannover TEL +49 (0)

More information

Adjustable Speaker Mount GRAVIS 12

Adjustable Speaker Mount GRAVIS 12 Adjustable Speaker Mount GRAVIS 12 User's Manual Translation of the original instructions Version 3.3 Released: 19.01.2017 Important Information, Please Read Before Use! KLING & FREITAG GmbH Junkersstraße

More information

Translation of the Original operating instructions Lifting device Z 70 /...

Translation of the Original operating instructions Lifting device Z 70 /... Translation of the Original operating instructions Lifting device Z 70 /... Content 1. Lifting device / Correct use according to regulations 2. Basic principles 3. General information 4. Special remarks

More information

Operator Instructions for Tension Links

Operator Instructions for Tension Links Operator Instructions for Tension Links Page 1 of 9 Table of Contents Introduction... 3 Markings CE... 3 Electromagnetic Compatibility (EMC)... 3 Tension Link Type/Model Number... 3 Supplier... 3 Service...

More information

Operating Instructions Hoist Chains EN 818-7

Operating Instructions Hoist Chains EN 818-7 Operating Instructions Hoist Chains EN 818-7 THIELE GmbH & Co. KG Werkstraße 3 Phone: +49 (0) 2371 / 947-0 58640 Iserlohn www.thiele.de B08285-B Page 1 EN-170114 Table of Contents 1 Introduction... 2 2

More information

Gunnebo Lifting Offshore programme - accessories. High consistent quality generates long durability and safety

Gunnebo Lifting Offshore programme - accessories. High consistent quality generates long durability and safety Gunnebo Lifting Offshore programme - accessories High consistent quality generates long durability and safety DNV 2.7-1 certificate We are certified by DNV to make type approval in 271 quality (Offshore

More information

Grade 80 Chain Sling Components. Grade 100 Chain Sling Components

Grade 80 Chain Sling Components. Grade 100 Chain Sling Components NGER: Overhead lifting presents a very real danger of severe injury or loss of life if lifting equipment is not used properly.lease read and understand all of these instructions prior to using any lifting

More information

Operating Instructions Garlock Butterfly Valves DN : mm / 2-24

Operating Instructions Garlock Butterfly Valves DN : mm / 2-24 Operating Instructions Garlock Butterfly Valves DN : 50-600 mm / 2-24 PN : 10 / 16 Type: GAR-SEAL SAFETY-SEAL STERILE-SEAL MOBILE-SEAL Conformity declaration... 14 0 Introduction... 15 1 Proper use...

More information

LIF TING SOLUTIONS. Lifting Solutions

LIF TING SOLUTIONS. Lifting Solutions Center Pull Style... 484-485 Envirolox Protective Finish... 494 Eye Bolts...500 Eye Nuts... 499 Forged Center Pull...487 488 Forged Center Pull Stainless Steel...486 Kwik-Lok Lifting Pin...495 496 Hold

More information

Tiger Lifting Home of the Tiger hoisting range & Tiger subsea lifting products

Tiger Lifting  Home of the Tiger hoisting range & Tiger subsea lifting products Tiger Lever Hoist Model No PROLH (with overload protection) Main Features Now available with slipping clutch overload protection Range 750kg - 10.0t Equipped with our unique dual brake mechanism New twin

More information

User Manual. T29870 Beam Clamp. Original Instructions. Rev /08//14.

User Manual. T29870 Beam Clamp. Original Instructions. Rev /08//14. User Manual T29870 Beam Clamp Original Instructions Rev 1.0-12/08//14 www.doughty-engineering.co.uk Contents Introduction... 2 Exclusion of Liability... 2 Safety Instructions... 2 Operation... 3 Maintenance...

More information

L Standard Parts for Mould Making

L Standard Parts for Mould Making A Die Sets B Precision Ground Plates and Flat Bars C Lifting and Clamping Devices Shanks, Lifter Studs and Lifting Hooks, Eyebolts Clamping Claws, Screws and Bolts D Guide Elements E Ground Precision Components

More information

INSTRUCTION MANUAL. Pacific Self-locking Beam Trolleys Pacific Adjustable Angle Clamps Pacific Top Girder Clamps

INSTRUCTION MANUAL. Pacific Self-locking Beam Trolleys Pacific Adjustable Angle Clamps Pacific Top Girder Clamps INSTRUCTION MANUAL Pacific Self-locking Beam Trolleys Pacific Adjustable Angle Clamps Pacific Top Girder Clamps IMPORTANT Please read this instruction manual before using these products. This manual contains

More information

A guide for the selection of alloy steel chain slings DLHONLINE. DLH Online Guides 02/14

A guide for the selection of alloy steel chain slings DLHONLINE. DLH Online Guides 02/14 A guide for the selection of alloy steel chain slings DLHONLINE Contents Page 3. Overview 4. Chain Systems 5. Stock chain and Components 6. Sling Loadings 7. Certification 8. Identification 9. Chain sling

More information

Wire rope accessories. 5. Wire rope accessories. Index

Wire rope accessories. 5. Wire rope accessories. Index Wire rope accessories 5. Wire rope accessories 1 General 1.1 About Hendrik Veder Group 1.2 Trade names 1.3 Certified Quality 1.4 Certificates 1.5 Key suppliers & brands 1.6 Contact information 1.7 Locations

More information

DLH ONLINE A GUIDE TO STANDARD EYE BOLTS, LIFTING POINTS AND HOIST RINGS FOR LIFTING PURPOSES. Benefits

DLH ONLINE A GUIDE TO STANDARD EYE BOLTS, LIFTING POINTS AND HOIST RINGS FOR LIFTING PURPOSES. Benefits DLH ONLINE A GUIDE TO STANDARD EYE BOLTS, LIFTING POINTS AND HOIST RINGS FOR LIFTING PURPOSES Benefits Safe use Types Applications Manufacturers Contact: Tel: 0845 270 2919 - INT: 00 44 161 223 1990 -

More information

CHAIN & HOOKS. Proof Coil Chain Grade 28. Transport Chain Grade 70

CHAIN & HOOKS. Proof Coil Chain Grade 28. Transport Chain Grade 70 Proof Coil Chain Grade 28 Proof coil chain is suitable for use as towing chain, logging,fencing, trailer safety chain, boat anchors, security barriers or other general purposes where chain of high tensile

More information

Index. The Benefits of Experience 2. Design and Manufacture 3. Quality 3. Slides and Hooks 4-7. Gambrels & S Hooks 8. Beef Rollers 9.

Index. The Benefits of Experience 2. Design and Manufacture 3. Quality 3. Slides and Hooks 4-7. Gambrels & S Hooks 8. Beef Rollers 9. Index The Benefits of Experience 2 Design and Manufacture 3 Quality 3 Slides and s 4-7 Gambrels & S s 8 Beef Rollers 9 Bleeders 10 Other Components 11-12 Notes on 13 Page 1 The Benefits of Experience.

More information

B Precision Ground Plates and Flat Bars. E Ground Precision Components. G Elastomer-Bars, -Sheets, -Sections

B Precision Ground Plates and Flat Bars. E Ground Precision Components. G Elastomer-Bars, -Sheets, -Sections A Die Sets B Precision Ground Plates and Flat Bars C Lifting and Clamping Devices Shanks, Lifter Studs and Lifting Hooks, Eyebolts Clamping Claws, Screws and Bolts D Guide Elements E Ground Precision Components

More information

Operating Instructions Hoist Chains EN 818-7

Operating Instructions Hoist Chains EN 818-7 Operating Instructions Hoist Chains EN 818-7 THIELE GmbH & Co. KG Werkstraße 3 Phone: +49 (0) 2371 / 947-0 58640 Iserlohn www.thiele.de B08285-A Page 1 EN-051110 Table of Contents 1 Introduction... 2 2

More information

WEIGHT CONTENTS SIZE DESCRIPTION WORKING LOAD LIMIT

WEIGHT CONTENTS SIZE DESCRIPTION WORKING LOAD LIMIT rade Chain LENTH S0606 3/8 6 8,800 lbs. 12.5 lbs. S0608 3/8 8 8,800 lbs. 15.5 lbs. S0610 3/8 10 8,800 lbs. 18.5 lbs. S0616 3/8 16 8,800 lbs. 27.3 lbs. S0620 3/8 20 8,800 lbs. 33.3 lbs. S0806 1/2 6 15,000

More information

Roughneck Mesh Slings

Roughneck Mesh Slings Roughneck Slings Roughneck WIRE MESH SLINGS Specialty Slings with Particular Properties and Uses Widely used in metalworking shops and steel warehouses where loads are abrasive, hot or tend to cut web

More information

OPERATIONS MANUAL LEVER CHAIN HOIST

OPERATIONS MANUAL LEVER CHAIN HOIST OPERATIONS MANUAL LEVER CHAIN HOIST IMPORTANT SAFETY INFORMATION Please read, understand and follow all safety information contained in these instructions prior to the use of this hoist. Retain these instructions

More information

Thomson Engineering Design Ltd. Drag Clamp. Operator s Instructions. Original Document in English Language. Issue 2 March 2015

Thomson Engineering Design Ltd. Drag Clamp. Operator s Instructions. Original Document in English Language. Issue 2 March 2015 Thomson Engineering Design Ltd Drag Clamp Operator s Instructions Original Document in English Language Issue 2 March 2015 Document Number: DC-Inst-01 Issue: 02 Date: March 2015 Introduction The Thomson

More information

MATERIALS HANDLING TECHNICAL MANUAL VOL. 2

MATERIALS HANDLING TECHNICAL MANUAL VOL. 2 5 Beaver maintains a comprehensive range of rigging hardware items for the most rigorous working environment. Comprising of turnbuckles in all configurations, collared Eyebolts and eye nuts, chain split

More information

Operating Manual. Pantographs. Version 05/12.

Operating Manual.   Pantographs. Version 05/12. Operating Manual Pantographs Version 05/12 Parts & Features A pantograph is a mechanical device that enables a load to be suspended by the means of balancing the load with two or more constant tension

More information

contents MALLEABLE PIPE FITTINGS BUsHEs NiPPlEs PlUgs caps BENds BackNUTs UNioNs TEEs 171 cross PN25 p socket PN25 p socket PN25 p.

contents MALLEABLE PIPE FITTINGS BUsHEs NiPPlEs PlUgs caps BENds BackNUTs UNioNs TEEs 171 cross PN25 p socket PN25 p socket PN25 p. contents BUsHEs 140 Hexagon Bush p.5 NiPPlEs 144 octagon Nipple p.6 145 Hexagon Nipple p.6 PlUgs 146 Beaded Plug - solid p.7 147 Plain Plug - Hollow p.7 148 Plain Plug - solid p.7 149 countersunk Plug

More information

OPW Emergency Safety Disconnector. Safety Breakaway Coupling Type NTS-PU Series (Pull-Away) Sizes 1-4 (DN25 DN100) Page 1

OPW Emergency Safety Disconnector. Safety Breakaway Coupling Type NTS-PU Series (Pull-Away) Sizes 1-4 (DN25 DN100) Page 1 OPW Emergency Safety Disconnector Safety Breakaway Coupling Type NTS-PU Series (Pull-Away) Sizes 1-4 (DN25 DN100) Page 1 Content Please read carefully the following OPW user manual to avoid incidents and

More information

...our linkages, your solution. Rod Ends

...our linkages, your solution. Rod Ends ...our linkages, your solution Technical Information Introduction All of our rod ends incorporate either a plain spherical bearing, ball bearing, or roller bearing. Below is an overview of each type. Plain

More information

Practice Note on the Sourcing of Threaded Rod Used for Foundation Bolts

Practice Note on the Sourcing of Threaded Rod Used for Foundation Bolts MATERIALS Practice Note on the Sourcing of Threaded Rod Used for Foundation Bolts Authors: Kevin Cowie, Alistair Fussell Affiliation: Steel Construction New Zealand Inc. Date: 20 th February 2018 Ref.:

More information

Before equipment use, please read this operation manual carefully. Serial Number: Date Purchased:

Before equipment use, please read this operation manual carefully. Serial Number: Date Purchased: Pushed & Geared Trolleys OPERATION MANUAL This operation manual is intended as an instruction manual for trained personnel who are in charge of installation, maintenance, repair etc. Before equipment use,

More information

Heavy-Duty Rod Ends - Male with integral spherical plain bearing

Heavy-Duty Rod Ends - Male with integral spherical plain bearing Heavy-Duty Rod Ends - Male with integral spherical plain bearing 65700 Order No. Thread (hand) d 1 l 1 d 2 d 3 d 4 l 2 l 3 X g H7 65700.W0005 Right 5 33 M 5 11,11 18 20 9 14 65700.W0006 Right 6 36 M 6

More information

Instructions for Fitting, Operating and Maintenance

Instructions for Fitting, Operating and Maintenance EN Instructions for Fitting, Operating and Maintenance Retractable Door 1 818 024 RE / 10.2011 ENGLISH Contents 1 Safety Instructions... 3 1.1 Qualified persons... 3 1.2 Symbols and signal words used...

More information

Tiger Lifting Home of the Tiger hoisting range & Tiger subsea lifting products

Tiger Lifting  Home of the Tiger hoisting range & Tiger subsea lifting products Tiger SS11 Subsea Lever Hoist with overload protection with overload protection with clevis adaptor and shackle Main Features DNV GL Verification tested according to NORSOK R-002 Available with slipping

More information

Operation and Maintenance Manual Model.75,, 3, 5, 8, 0, 0, 5, 35, 50 http://www.torsionx.com Use the MaxDrv Series Square Drive Torque Wrench Model.75,, 3, 5, 8, 0, 0, 5, 35, 50 to install and remove threaded

More information

Mounting and Operating Instructions EB 8135/8136 EN. Series V2001 Valves Type 3535 Three-way Valve for Heat Transfer Oil

Mounting and Operating Instructions EB 8135/8136 EN. Series V2001 Valves Type 3535 Three-way Valve for Heat Transfer Oil Series V2001 Valves Type 3535 Three-way Valve for Heat Transfer Oil Type 3535 Three-way Valve with bellows seal and rod-type yoke (partial view) Mounting and Operating Instructions EB 8135/8136 EN Edition

More information

Overhead transmission lines Spacers

Overhead transmission lines Spacers = SVENSKA KRAFTNÄT SWEDISH NATIONAL GRID UNIT, BUSINESS AREA AEL, Asset Management Lines OUR REFERENCE TR05-08E DATE 2016-06-09 CONSU12TATIONS TECHNICAL GUIDELINE REVISION 3 APPROVED Overhead transmission

More information

SERVO MOTORS BRUSHLESS SERVO MOTORS OPERATING INSTRUCTIONS 2016

SERVO MOTORS BRUSHLESS SERVO MOTORS OPERATING INSTRUCTIONS 2016 SERVO MOTORS BRUSHLESS SERVO MOTORS OPERATING INSTRUCTIONS 2016 3009/16 en Ed.02.2016 Read these Operating Instructions before performing any transportation, installation, commissioning, maintenance or

More information

Yellow Point WARNING NEVER EXCEED PUBLISHED WORKING LOAD LIMIT. Catalog No YP. Copyright 2017 YOKE Industrial Corp. All Rights Reserved.

Yellow Point WARNING NEVER EXCEED PUBLISHED WORKING LOAD LIMIT. Catalog No YP. Copyright 2017 YOKE Industrial Corp. All Rights Reserved. Yellow Point Catalog No. 8-2017.YP 2 3 Yellow Point 4 Worldwide Quality Type Approval And Certificate: 5 Quality Control, Testing, and Detecting during manufacturing YOKE runs a constant and strict production

More information

K&F Rotation Clamp 450

K&F Rotation Clamp 450 K&F Rotation Clamp 450 User's Manual Translation of the original instructions Version 1.3 Released: 29.03.2017 Important Information, Please Read Before Use! KLING & FREITAG GmbH Junkersstraße 14 D-30179

More information

Operating Instructions

Operating Instructions Operating Instructions Pendant Light Fitting > Contents 1 Contents 1 Contents...2 2 General Information...2 3 General Notes Regarding Safety...3 4 Intended Area of Application...4 5 Technical Data...5

More information

Lineman s Hoist. Operating, Maintenance & Parts Manual. Follow all instructions and warnings for LMST680-2

Lineman s Hoist. Operating, Maintenance & Parts Manual. Follow all instructions and warnings for LMST680-2 Lineman s Hoist LMST0- Operating, Maintenance & Parts Manual Lineman s Hoist Follow all instructions and warnings for inspecting, maintaining and operating this hoist. The use of any hoist presents some

More information

Belt Conveyor Pull Rope Switch Types HEN, HEK and SEM OPERATING INSTRUCTIONS

Belt Conveyor Pull Rope Switch Types HEN, HEK and SEM OPERATING INSTRUCTIONS Belt Conveyor Pull Rope Switch Types HEN, HEK and SEM OPERATING INSTRUCTIONS 2 CE-Sign and Conformity The device meets the requirements of the valid European and national regulations. Conformity has been

More information

Installation, Operation, and Maintenance Manual

Installation, Operation, and Maintenance Manual Industrial Process Installation, Operation, and Maintenance Manual Series PBV Plastic Lined Ball Valve Table of Contents Table of Contents Introduction and Safety...2 Safety message levels...2 User health

More information

Package Contents Part A (3) I-Beam (1) Base (2) Other parts

Package Contents Part A (3) I-Beam (1) Base (2) Other parts Page 1 Installation Instructions for 81245 Adjustable Height Gantry Crane 1-Ton Capacity Table of Contents Important Safety Information pg. 2 Specific Operation Warnings pg. 2 Main Parts of Product pg.

More information

Operating Instructions and Parts Manual 3-1/2 ton Farm Jack Model FJ-3-1/2A

Operating Instructions and Parts Manual 3-1/2 ton Farm Jack Model FJ-3-1/2A Operating Instructions and Parts Manual 3-1/2 ton Farm Jack Model FJ-3-1/2A JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-440436 Ph.: 800-274-6848 Revision A1 06/2014 www.jettools.com Copyright

More information

REBAR CONNECTION SYSTEM

REBAR CONNECTION SYSTEM REBAR CONNECTION SYSTEM WWW.TERWA.COM Terwa reserves the right to make changes to the documentation at any time Page 1 OVERVIEW COUPLERS PSA PSA-PSC PSC-BOLT PSE Page 6 Page 6 Page 8 Page 9 TSE PSA-SS

More information

Tension Meter. Edition FT 03.E. FT Series. Instruction Manual. Valid as of: Please keep the manual for future reference!

Tension Meter. Edition FT 03.E. FT Series. Instruction Manual. Valid as of: Please keep the manual for future reference! Tension Meter FT Series S C H M I D T c o n t r o l i n s t r u m e n t s Edition FT 03.E Model FT Instruction Manual Valid as of: 01.09.2011 Please keep the manual for future reference! Contents 1 Warranty

More information

JEFFERSON JOBOY. 27 November 2018

JEFFERSON JOBOY. 27 November 2018 JEFFERSON JOBOY 27 November 2018 1 LIFTING AWARENESS 2 GROUND RULES 3 What is a lifting operation? An operation concerned with the lifting or lowering of a load'. A 'load' is the item or items being lifted,

More information

Component for OTC No or No. 1750A Engine Mounting Adapter

Component for OTC No or No. 1750A Engine Mounting Adapter 655 EISENHOWER DRIVE OWATONNA, MN 55060-0995 USA PHONE: (507) 455-7000 TECH. SERV.: (800) 533-6127 FAX: (800) 955-8329 ORDER ENTRY: (800) 533-6127 FAX: (800) 283-8665 INTERNATIONAL SALES: (507) 455-7223

More information

Instructions for Fitting, Operating and Maintenance Canopy Door RE / (St.: )

Instructions for Fitting, Operating and Maintenance Canopy Door RE / (St.: ) EN Instructions for Fitting, Operating and Maintenance Canopy Door 1 818 012 RE / (St.: 12.2010) 12.2010 ENGLISH Contents 1 Safety Instructions... 3 1.1 Qualified persons... 3 1.2 Symbols and signal words

More information

Tugger T-Bolts Coupling (Extension) Nuts Eye Bolts Metric Coupling (Ext.) Nuts Latch Swing Bolts Heavy Hex Nuts...

Tugger T-Bolts Coupling (Extension) Nuts Eye Bolts Metric Coupling (Ext.) Nuts Latch Swing Bolts Heavy Hex Nuts... INDEX Threaded Rod... 4 T-Slot Nuts... 14 Driver Studs - Stainless Steel... 4 Stainless Steel T-Nuts... 14 Driver Studs... 4-5 Stainless Steel Flange Nuts... 15 Driver Studs Various Thread Lengths... 6

More information

MECHANICAL QUICK HITCH

MECHANICAL QUICK HITCH MECHANICAL QUICK HITCH Installation & Operation Manual Important: This manual must be kept with the excavator at all times and referred to as required Harford Attachments Ltd Table of Contents Item Checklist

More information

Electrically Released Brakes ERS VAR11-01 FT = 4100 N

Electrically Released Brakes ERS VAR11-01 FT = 4100 N SM429gb - rev 06/11 S E R V I C E Electrically Released Brakes ERS VAR11-01 FT = 4100 N M A N U A L EC type certificate ABV 775/1 According to drawing 1 12 106946 TUV SUD Industrie Service WARNER ELECTRIC

More information

Safelift Overhead Runway Beams & Rolling Beam Cranes

Safelift Overhead Runway Beams & Rolling Beam Cranes Operation & Maintenance Instructions Instructions for Safe Use Safelift Overhead Runway Beams & Rolling Beam Cranes Certification Safelift overhead runway beams and rolling beam cranes are lifting appliances

More information

Installation, Care and maintenance

Installation, Care and maintenance Installation, Care and maintenance DOCK-LOCK TM, Lifting system 892434/04 CONTENTS Safety 2 Guarantee 3 Data plate interpretation 3 Product description 4 Materials 4 Dimensions 4 Operation 8 Safety precautions

More information

ov-shoulder_screws_divider - Updated Shoulder Screws

ov-shoulder_screws_divider - Updated Shoulder Screws ov-shoulder_screws_divider - Updated - 09-01-2017 Shoulder Screws Product Overview & Shoulder Bolts Steel shoulder screws These are our least expensive option. They are produced to ISO 7379 standards.

More information

DOCUMENT TYPE = FITTING INSTRUCTIONS ORIGINAL LANGUAGE = ENGLISH. Maximum door weight = 40kg per leaf total system 80kg

DOCUMENT TYPE = FITTING INSTRUCTIONS ORIGINAL LANGUAGE = ENGLISH. Maximum door weight = 40kg per leaf total system 80kg Evolve SIM Kit DOCUMENT TYPE = FITTING INSTRUCTIONS ORIGINAL LANGUAGE = ENGLISH 80kg Maximum door weight = 40kg per leaf total system 80kg Maximum door width 2 x 2mtr Track = 675-1058mm (Up to 2035 mm

More information

Made. Quality. Rugged. American

Made. Quality. Rugged. American Quality Control for Safety s Sake Our quality control procedures define the entire manufacturing process and provide complete traceability from raw materials, tested in our metallurgical lab, to finished

More information

IBT Series Square Drive Torque Wrenches

IBT Series Square Drive Torque Wrenches IBT Series Square Drive Torque Wrenches Operation and Maintenance Manual Model.75, 1, 3, 5, 8, 10, 20, 25, 35, 50 http://www.torsionx.com Use the IBT Series Square Drive Torque Wrenches Model.75, 1, 3,

More information

Tiger Lifting Home of the Tiger hoisting, winching and height safety ranges

Tiger Lifting   Home of the Tiger hoisting, winching and height safety ranges Tiger Professional Lever Hoist Model No. PROLH with optional travelling end stop with spark resistant components with overload protection Main Features DNV GL Verification tested according to NORSOK R-002

More information

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS Emergency Cord Switch Type PRS Device identification No.: 91.054 033.001, /.101 and /.201 OPERATING INSTRUCTIONS 2 CE Sign and Conformity The device meets the requirements of the valid European and national

More information

Operating Instructions

Operating Instructions Operating Instructions Pendant Light Fitting > Contents 1 Contents 1 Contents...2 2 General Information...2 3 General Safety Instructions...3 4 Conformity to Standards...3 5 Intended Field of Application...3

More information

SHOP RIGGING & OVERHEAD HOIST SAFETY PROGRAM

SHOP RIGGING & OVERHEAD HOIST SAFETY PROGRAM Purpose & Scope CLIMATE ENGINEERS, INC. (CE) is dedicated to the protection of our employees from occupational injuries and illnesses. The purpose of this program is to provide procedures to be followed

More information

America s Largest Importer/Wholesaler of Wire Rope, Chain and Fittings!

America s Largest Importer/Wholesaler of Wire Rope, Chain and Fittings! America s Largest Importer/Wholesaler of Wire Rope, Chain and Fittings BLOCKS BINDERS Failure to design and use tackle block systems properly may cause a load to slip or fall - the result could be serious

More information

TONS. Before each shift: Before operating: Before initial operation of hoist:

TONS. Before each shift: Before operating: Before initial operation of hoist: LEVER HOIST 0.25 9 TONS Manual Notice It is the responsibility of the owner/user to install, inspect, test, maintain, and operate these lever hoists in accordance with ASME B30.21, Safety Standard for

More information

User Manual. Studio Rail. Size Version

User Manual. Studio Rail. Size Version User Manual Studio Rail Size 60 Version 10.1 Contents Contents: Introduction... 2 Exclusion of Liability... 2 Safety Instructions... 2 Operating Data...3-8 1. Selecting the correct carriage...3-5 2. Mounting

More information

JBL VTX-V20-DF SUSPENSION MANUAL

JBL VTX-V20-DF SUSPENSION MANUAL JBL VTX-V20-DF 1 Contents JBL VTX-V20-DF... 1 IMPORTANT SAFETY WARNING... 3 APPLICATION OF V20-DF... 7 ATTACHMENT OF V20-DF TO V25-II / V25-II-CS... 8 JBL VTX SERIES SUSPENSION PRECAUTIONS AND SAFETY INFORMATION

More information

Web Slings WEB SLING HARDWARE WARNING. Web Slings Steel Unilink Web Sling Hardware Combination Triangle and Choker Fitting U. S. Patent No.

Web Slings WEB SLING HARDWARE WARNING. Web Slings Steel Unilink Web Sling Hardware Combination Triangle and Choker Fitting U. S. Patent No. Web Slings Web Slings Steel Unilink Web Sling Hardware Combination Triangle and Choker Fitting U. S. Patent No. 4789193 WE SLING HARDWARE This forged, high carbon steel fitting, functions as both a triangle

More information

PLATE CLAMPS INSTRUCTION MANUAL

PLATE CLAMPS INSTRUCTION MANUAL PLATE CLAMPS INSTRUCTION MANUAL Imported exclusively by Pacific Hoists Pty. Ltd. & Pacific Hoists Ltd. In support of cancer charities in Australia & New Zealand Universal Plate Clamp 1 Horizontal Plate

More information

Lifting Devices Hoist Rings - Eye Bolts

Lifting Devices Hoist Rings - Eye Bolts Lifting Devices Hoist Rings - Eye Bolts Snap Rings - Hoist Rings Hoist Ring Accessories HOIST RING CLIPS Pg K3 SIDE LOAD HOIST RINGS Pg K5 CLIP RETAINERS Pg K6 SWIVEL HOIST RINGS Pg K2 FORGED SWIVEL HOIST

More information

Wilo Abrasive Separator SCP and NL Kits Installation and operating instructions

Wilo Abrasive Separator SCP and NL Kits Installation and operating instructions Wilo Abrasive Separator SCP and NL Kits Installation and operating instructions WIL-IO-AS-001-11 1 Description 2 Performance Characteristics The Abrasive (Sediment) Separator [AS] is used to remove fine

More information

Operation and Maintenance Manual http://www.torsionx.eu Use the MaxDrv Series Square Drive Torque Wrench Model.75, 1, 3, 5, 8, 10, 20, 25, 35, 50 to install and remove threaded fasteners requiring precise

More information

Installation and Operating Manual for Tank and Equipment Cleaning Nozzles Series 5TM

Installation and Operating Manual for Tank and Equipment Cleaning Nozzles Series 5TM Installation and Operating Manual for Tank and Equipment Cleaning Nozzles Series 5TM 150 150 150 This instruction manual contains proprietary information which is protected by copyright laws. No part of

More information

Swing blocks for wire rope

Swing blocks for wire rope EC Swing blocks for wire rope T 6055 GB 1 June 05 1/2 Applications The swing blocks of EC type are mainly used for temporary applications for lifting or pulling. They can be su spended to a fi xed or mobi

More information

Linear Guideways ov -linear -guidew ays-divider - U pdated

Linear Guideways ov -linear -guidew ays-divider - U pdated Linear Guideways ov-linear-guideways-divider - Updated - 11-01-2017 163 Linear Guideways Linear Guideways Introduction L1016 Linear guideways Linear guideways are widely used throughout industry for heavy-duty

More information

LOAD RATED FITTINGS STAINLESS STEEL LOAD RATED COMPONENTS HEIGHT SAFETY FITTINGS

LOAD RATED FITTINGS STAINLESS STEEL LOAD RATED COMPONENTS HEIGHT SAFETY FITTINGS LOAD RATED GRADE 316 STAINLESS STEEL FITTINGS STAINLESS STEEL LOAD RATED COMPONENTS HEIGHT SAFETY FITTINGS 37 Taree Street Burleigh QLD 4220 Telephone: (07) 55 935 688 Fax: (07 55 935 872 Email: bridge@bridco.com.au

More information

ROOFING SOLUTIONS DESIGN GUIDE PURLINS AND GIRTS DESIGN GUIDE PURLINS AND GIRTS S&T029N

ROOFING SOLUTIONS DESIGN GUIDE PURLINS AND GIRTS DESIGN GUIDE PURLINS AND GIRTS S&T029N DESIGN GUIDE PURLINS AND GIRTS ROOFING SOLUTIONS DESIGN GUIDE PURLINS AND GIRTS S&T029N JUL 2015 CONTENTS INTRODUCTION 2 Acknowledgements 2 Disclaimer 2 Product Technical Statement 3 Producer Statement

More information

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS Emergency Cord Switch Type LRS 004 Device identification no.: 93.046 690.004 OPERATING INSTRUCTIONS 2 CE-Sign and Conformity The device meets the requirements of the valid European and national regulations.

More information

Quick-find Index. Lifting & Rigging

Quick-find Index. Lifting & Rigging Burncrete s core business is the supply of lifting, rigging, pulling and lashing equipment to the mining, industrial, construction, transport, railways and harbours sectors, via re sellers, agents and

More information

Tiger Lifting Home of the Tiger hoisting, winching and height safety ranges

Tiger Lifting   Home of the Tiger hoisting, winching and height safety ranges Tiger Corrosion Resistant Chain Block Model No. SS12 with clevis adaptor and shackle Spark resistant option Main Features Suitable for use in multi-immersion applications DNV GL Verification tested according

More information

Heavy Duty Engine Cranes

Heavy Duty Engine Cranes Heavy Duty Engine Cranes Operating Instructions & Parts Manual Model Number Atd-7484 Atd-7485 (Foldable Legs) Capacity 2 Ton 2 Ton Model Atd-7484 Model Atd-7485 Atd Tools Inc. 160 Enterprise Drive, Wentzville,

More information

Polyester Lifting Slings

Polyester Lifting Slings Est. 969 Polyester Lifting Slings FASTLIFT Endless Roundsling (ERS) Roundslings with seamless single cover and protected label WLL Colour Weight Rec. min Rec. min Standard size range available (tonnes)

More information

Piston rod attachments

Piston rod attachments Piston rod attachments q/w Worldwide: Superb: Easy: Festo core product range Covers 80% of your automation tasks Always in stock Festo quality at an attractive price Reduces procurement and storing complexity

More information

Operation and Maintenance Manual

Operation and Maintenance Manual Operation and Maintenance Manual Lineman s Hoist Models 250A 300A 250DA 300DA PUBLICATION PART NO. LM931A IMPORTANT! CAUTION This manual contains important information for the correct installation, operation

More information

Flexible Arm Stand F 360. User Manual

Flexible Arm Stand F 360. User Manual User Manual To ensure proper use of this instrument as well as to avoid injury while operating instrument, understanding this manual completely before use is highly recommended. Flexible Arm Stand User

More information