Installation Instructions
|
|
|
- Lucas Curtis
- 6 years ago
- Views:
Transcription
1 Installation Instructions (Cat. No ASB Series B) , Component Identification 1 Remote I/O Adapter module 2 Indicators 3 Communication reset pushbutton (PRL) 4 Access door to switches S1 and S2 5 Switches S1 and S2 (behind access door) 6 Remote I/O cable connector 7 +24V dc connections 8 24V common connections 9 Flexbus connector FLEX I/O is a trademark of Allen-Bradley Co. Inc.
2 2 FLEX I/O Remote I/O Adapter European Union Directive Compliance If this product has the CE mark it is approved for installation within the European Union and EEA regions. It has been designed and tested to meet the following directives. EMC Directive This product is tested to meet Council Directive 89/336/EEC Electromagnetic Compatibility (EMC) and the following standards, in whole or in part, documented in a technical construction file: EN EMC Generic Emission Standard, Part 2 Industrial Environment EN EMC Generic Immunity Standard, Part 2 Industrial Environment This product is intended for use in an industrial environment. Low Voltage Directive This product is tested to meet Council Directive 73/23/EEC Low Voltage, by applying the safety requirements of EN Programmable Controllers, Part 2 Equipment Requirements and Tests. For specific information required by EN , see the appropriate sections in this publication, as well as the following Allen-Bradley publications: Industrial Automation Wiring and Grounding Guidelines For Noise Immunity, publication Guidelines for Handling Lithium Batteries, publication AG-5.4 Automation Systems Catalog, publication B111
3 FLEX I/O Remote I/O Adapter 3 Mounting on the DIN Rail A B C C 1. Position the remote I/O adapter module A on a 35 x 7.5mm DIN rail B (A-B pt. no. 199-DR1; ; EN 50022) at a slight angle. 2. Hook the lip on the rear of the adapter (A) onto the top of the DIN rail (B), and rotate the adapter module onto the rail. 3. Press the adapter module down onto the DIN rail until flush. Locking tab (C) will snap into position and lock the adapter module to the DIN rail. 4. If the adapter module does not lock in place, use a screwdriver or similar device to move the locking tab down while pressing the adapter module flush onto the DIN rail and release the locking tab to lock the adapter module in place. If necessary, push up on the locking tab to lock. 5. Connect the adapter wiring as shown under Wiring later in this document. NOTE: For Panel/Wall mounting, refer to publication , Panel Mounting Kit, Cat. No NM1.
4 4 FLEX I/O Remote I/O Adapter Wiring Allen-Bradley ADAPTER ACTIVE FAULT LOCAL FAULT 24 VDC POWER SUPPLY RIO ADAPTER 1794 ASB2 D COM F E 24V G 1 SH Connect the remote I/O cable to the removable remote I/O connector. Connect To Blue Wire RIO 1 Shield Wire RIO SH Clear Wire RIO 2 2. Connect +24V dc input to the left side of the lower connector, terminal E. 3. Connect 24V common to the left side of the upper connector, terminal D. 4. Connections G and F are used to pass 24V dc power (G) and 24V common (F) to the next module in the series (if required).
5 FLEX I/O Remote I/O Adapter 5 Set the Adapter Switches The adapter switches are located under a flip-open cover on the front of the adapter. Set the switches as shown below ON S1 ON S2 Flip-open cover
6 6 FLEX I/O Remote I/O Adapter First I/O Group I/O Rack Number ON S1 First I/O Group ON S Reserved Hold Inputs Last Adapter Reply Delay I/O Rack Number S1 8 S1 7 Module group S1 6 thru S1 1 ON ON 0 (1st) OFF ON 2 (2nd) ON OFF 4 (3rd) OFF OFF 6 (4th) Refer to the table on page 7 Communication Rate Processor Restart Lockout Hold Last State S2 8 S2 7 Hold Inputs S2 6 Last Adapter S2 5 Reply Delay Reserved ON Hold Inputs ON Not last ON Off OFF Reset Inputs OFF Last OFF On Communication Rate Processor Restart Lockout Hold Last State S2 4 S2 3 Bits/s S2 2 Processor: S2 1 Processor will: ON ON 57.6k ON Restart ON Reset Outputs OFF ON 115.2k OFF Locked Out OFF Hold last state ON OFF 230.4k OFF OFF 230.4k
7 FLEX I/O Remote I/O Adapter 7 Rack Number S1 Switch Position 1747-SN PLC 2 & 1771-SN PLC 5 PLC 5/250 PLC Rack 0 Rack 1 Not Valid Rack 0 Rack 0 ON ON ON ON ON ON Rack 1 Rack 2 Rack 1 Rack 1 Rack 1 OFF ON ON ON ON ON Rack 2 Rack 3 Rack 2 Rack 2 Rack 2 ON OFF ON ON ON ON Rack 3 Rack 4 Rack 3 Rack 3 Rack 3 OFF OFF ON ON ON ON Rack 5 Rack 4 Rack 4 Rack 4 ON ON OFF ON ON ON Rack 6 Rack 5 Rack 5 Rack 5 OFF ON OFF ON ON ON Rack 7 Rack 6 Rack 6 Rack 6 ON OFF OFF ON ON ON Rack 7 Rack 7 Rack 7 OFF OFF OFF ON ON ON Rack 10 Rack 10 Rack 10 ON ON ON OFF ON ON Rack 11 Rack 11 Rack 11 OFF ON ON OFF ON ON Rack 12 Rack 12 Rack 12 ON OFF ON OFF ON ON Rack 13 Rack 13 Rack 13 OFF OFF ON OFF ON ON Rack 14 Rack 14 Rack 14 ON ON OFF OFF ON ON Rack 15 Rack 15 Rack 15 OFF ON OFF OFF ON ON Rack 16 Rack 16 Rack 16 ON OFF OFF OFF ON ON Rack 17 Rack 17 Rack 17 OFF OFF OFF OFF ON ON Rack 20 Rack 20 Rack 20 ON ON ON ON OFF ON Rack 21 Rack 21 Rack 21 OFF ON ON ON OFF ON Rack 22 Rack 22 Rack 22 ON OFF ON ON OFF ON Rack 23 Rack 23 Rack 23 OFF OFF ON ON OFF ON Rack 24 Rack 24 Rack 24 ON ON OFF ON OFF ON Rack 25 Rack 25 Rack 25 OFF ON OFF ON OFF ON Rack 26 Rack 26 Rack 26 ON OFF OFF ON OFF ON Rack 27 Rack 27 Rack 27 OFF OFF OFF ON OFF ON Rack 30 Rack 30 ON ON ON OFF OFF ON Rack 31 Rack 31 OFF ON ON OFF OFF ON Rack 32 Rack 32 ON OFF ON OFF OFF ON Rack 33 Rack 33 OFF OFF ON OFF OFF ON Rack 34 Rack 34 ON ON OFF OFF OFF ON Rack 35 Rack 35 OFF ON OFF OFF OFF ON Rack 36 Rack 36 ON OFF OFF OFF OFF ON Rack 37 Rack 37 OFF OFF OFF OFF OFF ON Rack 40 ON ON ON ON ON OFF Rack 41 OFF ON ON ON ON OFF Rack 42 ON OFF ON ON ON OFF Rack 43 OFF OFF ON ON ON OFF Rack 44 ON ON OFF ON ON OFF Rack 45 OFF ON OFF ON ON OFF Rack 46 ON OFF OFF ON ON OFF Rack 47 OFF OFF OFF ON ON OFF Rack 50 ON ON ON OFF ON OFF Rack 51 OFF ON ON OFF ON OFF Rack 52 ON OFF ON OFF ON OFF Rack 53 OFF OFF ON OFF ON OFF Rack 54 ON ON OFF OFF ON OFF
8 8 FLEX I/O Remote I/O Adapter 1747-SN PLC 2 & 1771-SN Rack Number PLC 5 PLC 5/250 PLC S1 Switch Position Rack 55 OFF ON OFF OFF ON OFF Rack 56 ON OFF OFF OFF ON OFF Rack 57 OFF OFF OFF OFF ON OFF Rack 60 ON ON ON ON OFF OFF Rack 61 OFF ON ON ON OFF OFF Rack 62 ON OFF ON ON OFF OFF Rack 63 OFF OFF ON ON OFF OFF Rack 64 ON ON OFF ON OFF OFF Rack 65 OFF ON OFF ON OFF OFF Rack 66 ON OFF OFF ON OFF OFF Rack 67 OFF OFF OFF ON OFF OFF Rack 70 ON ON ON OFF OFF OFF Rack 71 OFF ON ON OFF OFF OFF Rack 72 ON OFF ON OFF OFF OFF Rack 73 OFF OFF ON OFF OFF OFF Rack 74 ON ON OFF OFF OFF OFF Rack 75 OFF ON OFF OFF OFF OFF Rack 76 ON OFF OFF OFF OFF OFF Not Valid OFF OFF OFF OFF OFF OFF Rack address 77 is an illegal configuration. PLC-5/11 processors can scan rack 03. PLC-5/15 and PLC-5/20 processors can scan racks PLC-5/25 and PLC-5/30 processors can scan racks PLC-5/40 and PLC-5/40L processors can scan racks PLC-5/60 and PLC-5/60L processors can scan racks PLC-5/80 processors can scan racks PLC-5/250 processors can scan racks
9 FLEX I/O Remote I/O Adapter ASB Specifications I/O Capacity Power Supply Input Voltage Rating Input Voltage Range Communication Rate Indicators Flexbus Output Current Isolation Voltage Power Consumption Power Dissipation Thermal Dissipation Environmental Conditions Operational Temperature Storage Temperature Relative Humidity Shock Operating Non-operating Vibration Remote I/O Cable Power Conductors Wire Size Category Specifications continued on next page 8 modules Note: In order to comply with CE Low Voltage Directives, you must use a Safety Extra Low Voltage (SELV) or a Protected Extra Low Voltage (PELV) power supply to power this adapter. 24V dc nominal 19.2V to 31.2V dc (includes 5% ac ripple) 57.6k bps 115.2k bps 230.4k bps Adapter Active green Adapter fault red Local fault red 640mA maximum 100% tested at 850V dc for 1s between user power and flexbus 450mA maximum from external 24V supply 4.6W 31.2V dc V dc 0 to 55 o C (32 to 131 o F) 40 to 85 o C ( 40 to 185 o F) 5 to 95% noncondensing 30 g peak acceleration, 11(+1)ms pulse width 50 g peak acceleration, 11(+1)ms pulse width Tested Hz per IEC Belden 9463 or equivalent as specified in publication ICCG gauge (4mm 2 ) stranded maximum 3/64 inch (1.2mm) insulation max. 2 1
10 10 FLEX I/O Remote I/O Adapter 1794-ASB Specifications Agency Certification (when product or packaging is marked) CSA certified CSA Class I, Division 2 Groups A, B, C, D certified UL listed CE marked for all applicable directives User Manual Publication Use this conductor category information for planning conductor routing. Refer to publication , Industrial Automation Wiring and Grounding Guidelines.
11 FLEX I/O Remote I/O Adapter 11 Mounting Dimensions Inches (Millimeters) 3.4 (87) 3.2 (80).83 (21) A 1.4 (35) 2.3 (59) 2.0 (50) 1.2 (28) 2.7 (68) 1794-ASB 3.4H x 2.7W x 2.7D (87H x 68W x 69D) A = Mounting hole dimensions for optional mounting kit B = DIN rail C = Secure DIN rail approximately every 200mm B C
12 12 FLEX I/O Remote I/O Adapter With major offices worldwide. World Headquarters, Allen-Bradley, 1201 South Second Street, Milwaukee, WI USA, Tel: (1) Fax: (1) Supersedes publication December 1995 PN Copyright 1995 Allen-Bradley Company, Inc. Printed in USA
Direct Communication Module
Installation Instructions Direct Communication Module (Catalog Number 1747-DCM) Inside...................................... page For More Information.............................. 3 Hazardous Location
Lexium integrated drives
Description ILp for CANopen, PROFIBUS DP, RS ILE with brushless DC motor Description ILE comprise control electronics with a fieldbus interface for CANopen DS, PROFIBUS DP or RS and a brushless DC motor.
Lexium integrated drives
Description ILp for DeviceNet, EtherCAT, Modbus TCP, ILE with brushless DC motor Description ILE comprise control electronics with a fieldbus interface for DeviceNet, EtherCAT, Modbus TCP or and a brushless
DC/DC converters - MINI-PS DC/ 5-15DC/
Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid
DuraDrive MF /MS Series Non-spring Return Rotary Electronic Damper Actuators 24 Vac Three-position/Modulating
General Instructions DuraDrive MF4-653/MS4-653 Series Non-spring Return Rotary Electronic Damper Actuators 4 Vac Three-position/Modulating Description The DuraDrive direct-coupled, 4 Vac, non-spring return
Compact Circuit Protector
Technical Data 10801 Supersedes August 018 BUSSMANN SERIES Compact Circuit Protector (cat. no. CCP) Contents Page 011/65/EU and specifications.... -3 Catalog numbers.... 4 Conductor information and available
MF /MS Series
MF41-6153/MS41-6153 Series 24 Vac, Three-position/Modulating Non-spring Return Rotary Electronic Damper SmartX Actuators General Instructions Description The direct-coupled, 24 Vac, non-spring return electronic
AF / AF09Z pole Contactors AC / DC Operated - with Screw Terminals
Technical Datasheet SBC042D020 06/04/ -22-00-.. / Z-22-00-.. 4-pole Contactors AC / DC Operated - with Screw Terminals (Z) contactors are used for controlling power circuits up to 690 V AC and 440 V DC.
AF / AF09Z pole Contactors AC / DC Operated - with Screw Terminals
Technical Datasheet 1SBC101419D0201 06/04/11-40-00-.. / Z-40-00-.. 4-pole Contactors AC / DC Operated - with Screw Terminals (Z) contactors are used for controlling power circuits up to 690 V AC and 440
Bulletin 1489 Circuit Breakers. Selection Guide
Bulletin 1489 s Selection Guide Bulletin 1489-A Overview/Description Bulletin 1489-A s Energy-limiting design protects downstream components better than conventional breakers during short circuits Field-mountable
Packing Data Installation Instructions
Packing Data PK Installation Instructions This document describes how to install a Dataliner DL10 display in a panel or enclosure and connect power. European Union Directive Compliance wiring and safety
OpenAir Electric Damper Actuators GDE/GLB Series Non-spring Return Rotary 24 Vac - Modulating Control 0 to 10 Vdc
Technical Instructions Document No. 155-187P25 EA GDE/GLB-1 OpenAir Electric Damper Actuators GDE/GLB Series Non-spring Return Rotary 24 Vac - Modulating Control 0 to 10 Vdc Description The OpenAir direct
Application Support. Product Information. Omron STI. Support Engineers are available at our USA headquarters from
Omron STI Application Support Thank you for your interest in Omron STI products. Please contact Omron STI with your application questions. Support Engineers are available at our USA headquarters from 4:00
BUSSMANN. Next generation Compact Circuit Protector (cat. no. CCP2) SERIES. For use with Class CC, Supplemental and IEC 10x38 mm fuses
Technical Data 10789 BUSSMANN SERIES Next generation Compact Circuit Protector (cat. no. CCP2) Contents Page 2011/65/EU CCP2 switch and specifications.... 2-3 Catalog numbers.... 4 Conductor information
AF / AF38Z pole Contactors AC / DC Operated - with Screw Terminals
Technical Datasheet 1SBC101412D0201 25/03/11-30-00-.. / Z-30-00-.. 3-pole Contactors AC / DC Operated - with Screw Terminals (Z) contactors are used for controlling power circuits up to 690 V AC and 220
Speed Sensor. Inputs: Safety Information. Outputs. Wiring Diagram. Electrical Data: NOTICE
Speed Sensor ã Read and understand equipment operators manual before operating or performing maintenance. Failure to do so could result in serious injury or death. Safety Information Failure to follow
AF / AF16Z pole Contactors AC / DC Operated - with Screw Terminals
Technical Datasheet 1SBC101408D0201 25/03/11-30-01-.. / Z-30-01-.. 3-pole Contactors AC / DC Operated - with Screw Terminals (Z) contactors are used for controlling power circuits up to 690 V AC and 220
Compact Circuit Protector
Supersedes February 2019 BUSSMANN SERIES Compact Circuit Protector (cat. no. CCP2) 2011/65/EU CCP2 switch up to 100 A 200 A CCP2 switch 400 A CCP2 switch Contents Page 30, 60 and 100 amp switches s and
Control Power V AC, 50/60 Hz 150-C30NBD 150-C30FHD
Bulletin Product Selection Open Type and Non-Combination Enclosed (IP, NEMA /) Controllers For use with Line-Connected Motors Rated Voltage [V AC] / Motor Current [A]...... Max. kw, Hz Max. Hp, Hz Control
Compact Circuit Protector (CCP)
Supersedes April 2014 UL Class CC, CF (CUBEFuse ), Midget and IEC 10x38mm DIN-Rail Contents Description Page Description Page 1-, 2- and 3-Pole Class CC, Midget, 10x38mm Description & Specifications....
AF40... AF96 3-pole contactors Technical data
Main pole - Utilization characteristics according to IEC Standards IEC 60947- / 60947-4- and EN 60947- / 60947-4- Rated operational voltage Ue max. 690 V Rated frequency (without derating) 50 / 60 Hz Conventional
CAUTION CM-SE CM-S21 CM-S41
CAUTION Safety, Technology & Innovation CM Series Operating Instructions for, CM-S21,, CM-S11, CMS31 CM Series Safety System This information is designed to help suitably qualified personnel install and
Safety Standards. Model Number:
Highlights & Features RoHS Compliant Relay alarm indirection Built-in 2 channel DC OK signal Caused by rugged handing Conformal coating on PCBA to protect against chemical and dust pollutants Class I,
Compact Circuit Protector (CCP) 1-, 2- and 3-pole Class CC, Midget, 10x38mm
Supersedes October 2015 BUSSMANN SERIES UL Class CC, CF (CUBEFuse ), midget and IEC 10x38mm DIN-Rail Contents Description Page Description Page 1-, 2- and 3-pole Class CC, Midget, 10x38mm Description and
Certifications UL Listed (File No. E 14841, Guide NLRV; File No. E 47426, Guide WHTY) CSA Certified (File No. LR1234) CE
Bulletin R Overview Bulletin R Next Generation Global Fused and Non-Fused Disconnects 0 A A Sizes Fused Switch Versions: - BS - DIN - CSA HRCII-C - CSA HRCI-MISC - UL Class J - UL Class CC - NFC Non-Fused
MINI-DC-UPS/24DC/2. Extract from the online catalog. Order No.:
Extract from the online catalog MINI-DC-UPS/24DC/2 Order No.: 2866640 Uninterruptible power supply with integrated power supply unit, 2 A, in combination with MINI-BAT/24/DC 0.8 AH or 1.3 AH Commercial
AF09... AF38 4-pole Contactors AC / DC Operated - with Screw Terminals
AF09... AF38 4-pole Contactors AC / DC Operated - with Screw Terminals 25 to 55 A culus CE Application AF09... AF38 4-pole contactors are used for controlling power circuits up to 600 V AC and 240 V DC.
AF / AF30Z stack 3-pole Contactors AC / DC Operated - with Screw Terminals
Technical Datasheet 1SBC101415D0201 25/03/11 AF30-30-11-.. / AF30Z-30-11-.. 2-stack 3-pole Contactors AC / DC Operated - with Screw Terminals AF30(Z) contactors are used for controlling power circuits
1329I Integrated Drive/Motor CE Filter Option Kit
Instruction Sheet 1329I Integrated Drive/Motor CE Filter Option Kit CE filter options are designed to be used with the 1329I Integrated Drive/Motor. The main function of the CE filter is to reduce the
Emergency lighting units EM powerled
BASIC FX SR 50 W Combined emergency lighting LED Driver Product description Independent fixed output LED Driver for mains operation with integrated Simple CORRIDOR FUNCTION (CF) Emergency lighting function
Technical Documentation
Technical Documentation Product manual Holding brake controller Document: 0198441113316 Edition: V1.00, 03.2006 Important information The drive systems described here are products for general use that
Model Number Structure
Solid State Relays (Single-phase) G3PB New Single-phase Solid State Relays with Compact Size for Heater Control Slim models with a thickness of only 22.5 mm are also available. Compact design achieved
Compact Circuit Protector (CCP)
Supersedes March 2016 BUSSMANN SERIES UL Class CC, CF (CUBEFuse ), midget and IEC 10x38mm DIN-Rail 2011/65/EU Contents Description Page Description Page 1-, 2- and 3-pole Class CC, Midget, 10x38mm Description
OpenAir Electric Damper Actuators GDE/GLB Series Non-spring Return Rotary 24 Vac - Modulating Control 0 to 10 Vdc
Document No. 155-187P25 EA GDE/GLB-1 OpenAir Electric Damper Actuators GDE/GLB Series Non-spring Return Rotary 24 Vac - Modulating Control 0 to 10 Vdc Description The OpenAir direct coupled 24 Vac non-spring
DATASHEET - DILMC9-10(24VDC) Technical data General. Contactor, 3p+1N/O, 4kW/400V/AC3. Catalog No Eaton Catalog No. XTCEC009B10TD.
DATASHEET - DILMC9-10(24VDC) Technical data General Contactor, 3p+1N/O, 4kW/400V/AC3 Part no. DILMC9-10(24VDC) Catalog No. 277468 Eaton Catalog No. XTCEC009B10TD EL-Nummer 4110305 (Norway) Standards IEC/EN
Safety Relay Unit. Ordering Information. Ideal for Safety Door and Emergency Stop Switch Circuits for Machines in European Countries
Safety Relay Unit Ideal for Safety Door and Emergency Stop Switch Circuits for Machines in European Countries Two-pole slim models that are only 22.5 mm wide, three-pole models that are only 68 mm wide,
LDX-C120 Series is a 120 W integrated DIN Rail Battery Charger / DC UPS Power Supplies, suitable for wide variety of industrial applications.
LDX-C120 Series is a 120 W integrated DIN Rail Battery Charger / DC UPS Power Supplies, suitable for wide variety of industrial applications. In case of mains or unit failure the DC UPS function enables
SIRIUS 3RU2 Thermal Overload Relays
Overview 1 2 3 4 6 1 2 NSB0_0207a Connection for mounting onto contactors: Optimally adapted in electrical, mechanical and design terms to the contactors. The overload relay can be connected directly to
1489-M Circuit Breakers
Dual terminals provide wiring/bus bar flexibility and clamp from both sides to improve connection reliability Terminal design helps prevent wiring misses Scratch- and solventresistant printing Suitable
AF09... AF30 3-pole Contactors up to 20 HP / 480 VAC
AF0... AF0 -pole Contactors up to 20 HP / 480 VAC Contactors and Overload Relays Overview...2 AF0... AF0 -pole Contactors Ordering Details...4 Main Technical Data...20 DC Circuit switching...2 Main Accessory
GETTING STARTED GUIDE NI AI, ±10 V, 16 Bit, 1 MS/s/ch Simultaneous
GETTING STARTED GUIDE NI 9223 4 AI, ±10 V, 16 Bit, 1 MS/s/ch Simultaneous This document explains how to connect to the NI 9223. Note Before you begin, complete the software and hardware installation procedures
4 Redundant Control System
4 Redundant Control System Introducing the all NEW RCS Configurator Safety Instrumented Systems Process Reliability Process Valve Diagnostics COMPLETE FUNCTIONAL SAFETY WITH ENHANCED RELIABILITY The Redundant
Low voltage AC drives. ABB micro drives ACS to 3 hp/0.18 to 2.2 kw Catalog
Low voltage AC drives ABB micro drives ACS55 0.25 to 3 hp/0.18 to 2.2 kw Catalog ACS55 IP20 Overview ACS55 micro drives are designed for use in a wide variety of simple machinery applications where only
OpenAir Electric Damper Actuator GDE/GLB Series Non-spring Return Rotary 24 Vac 3-position Control
OpenAir Electric Damper Actuator GDE/GLB Series Non-spring Return Rotary EA GDE/GLB-2 Description OpenAir direct coupled 24 Vac non-spring return rotary electric actuators are designed for 3-position (floating)
SIGMA SERIES DE METER
SIGMA SERIES DE METER Analogue Meters www.sifamtinsley.co.uk DATASHEET Issue 1.0 Multifunction Meters Transducers & Isolators Temperature Controllers Converters & Recorders Digital Panel Meters Current
Application Description
-14 Type, Intelligent Technologies (IT.) Soft Starters February 2007 Contents Description Page Type, Intelligent Technologies (IT.) Soft Starters Product Description....... -14 Application Description....
Document: PRODSPEC-140 Revision: G DCN No Date: October 1, 2014 Product: 10-amp EnerGenius NRG Battery Charger
Document: PRODSPEC-140 Revision: G DCN No. 106512 Date: October 1, 2014 Product: 10-amp EnerGenius NRG Battery Charger 1. GENERAL DESCRIPTION 1.1 General Description Fully regulated, constant voltage,
AF / AF12Z pole Contactors AC / DC Operated - with Screw Terminals
Technical Datasheet 1SBC101404D0201 24/03/11-30-10-.. / Z-30-10-.. 3-pole Contactors AC / DC Operated - with Screw Terminals (Z) contactors are used for controlling power circuits up to 690 V AC and 220
Rotary Disconnect Switches, Bulletin 194R
ROCKWELL AUTOMATION PROCUREMENT SPECIFICATION PROCUREMENT SPECIFICATION Rotary Disconnect Switches Bulletin 194R NOTICE: The specification guidelines in this document are intended to aid in the specification
Industrial Power Supplies
, Features Switch Mode Power Supplies for DIN-rail Mounting 6 Power Ranges with 2, 3, 6, 12, 20 and 24 A Current (24 VDC Models) Selectable 115/ 230 VAC Input Very low Ripple and Noise EMI complies with
Power Supplies. Series FLEX Power Supplies...P2 Technical Information & Dimensions (Online)...P5. ADEL Power Supplies
ower Supplies Series...2 Technical Information & Dimensions (Online)...5 ADEL ower Supplies 1 Flexible Switching ower Supplies Sprecher + Schuh is proud to bring you a Flexible ower Supply from the best
Climatic proofing Damp heat, constant, to IEC Damp heat, cyclic, to IEC mm
DATASHEET - M22-L-W Delivery program Indicator light, flush, white Part no. M22-L-W Catalog No. 216771 Eaton Catalog No. M22-L-WQ EL-Nummer 4355332 (Norway) Product range RMQ-Titan Basic function Indicator
Bulletin 1494F Fixed-Depth Flange-Mounted Disconnect Switches. Selection Guide
F Fixed-Depth Flange-Mounted Disconnect Switches Selection Guide F Fixed-Depth Flange-Mounted Disconnect Switches Product Cat. No. 1494F-N Disconnect Switch with Cat. No. 1494F-F Fuse Block Adapter Plate
OpenAir Electric Damper Actuator GDE/GLB Series Non-spring Return, 24 Vac Floating Control, Rotary
EA GDE/GLB-2 OpenAir Electric Damper Actuator GDE/GLB Series Non-spring Return, 24 Vac Floating Control, Rotary Description OpenAir non-spring return, 24 Vac, floating control, direct-coupled, actuators
NF31E-.. / NFZ31E-.. Contactor Relays AC / DC Operated - with Screw Terminals
Technical Datasheet 1SBC101428D0201 28/03/11 -.. / NFZ31E-.. Contactor Relays AC / DC Operated - with Screw Terminals NF(Z) contactor relays are used for switching auxiliary and control circuits. NF(Z)
NEW The new PROmax power supplies offer a wide range of robust solutions for demanding application requirements.
Datasheet Single- and three-phase switched-mode power supply units NEW The new power supplies offer a wide range of robust solutions for demanding application requirements. C SEMI F47 US Designed for high
I r A short-circuit protective device: Observe the maximum permissible fuse of the contactor with direct device mounting.
DATASHEET - ZB12-2,4 Delivery program Overload relay, 1.6-2.4 A, 1N/O+1N/C Part no. ZB12-2,4 Catalog No. 278437 Eaton Catalog No. XTOB2P4BC1 EL-Nummer 0004131832 (Norway) Product range Overload relay ZB
800 T FX 1 A1. Color Cap. No cap 1 Green 2 Black 3 Orange 4 Grey 5 White 6 Red 7 Blue 9 Yellow. Contact Block(s) Operator Position.
2-Position Push-Pull and Push-Pull/Twist Release Devices, Non-Illuminated Note: A jumbo or large legend plate is recommended, if space allows. 2-Position Push-Pull Cat. No. 800T-F6D4 2-Position Metal Push-Pull
CATALOG. ABB micro drives ACS55, 0.18 to 2.2 kw
CATALOG ABB micro drives ACS55, 0.18 to 2.2 kw 2 ABB MICRO DRIVES, ACS55, 0.18 TO 2.2 KW/0.25 TO 3 HP Ease of integration. ACS55 drives. 3 Table of contents 004 ABB micro drives, ACS55 005 Easily integrated
SITRANS P measuring instruments for pressure
Overview Application The pressure transmitter is designed for the special requirements of the food, pharmaceutical and biotechnology industries. The use of high-grade materials guarantees compliance with
These documents contain additional information concerning related products from Rockwell Automation.
Additional Resources These documents contain additional information concerning related products from Rockwell Automation. Title PowerFlex 0-Series Drive Installation Instructions PowerFlex 0-Series Programming
AF40... AF96 3-pole contactors 30 to 60 hp at 480 V AC AC / DC operated with 1 N.O. + 1 N.C. auxiliary contacts
AF4... AF96 -pole contactors to 6 hp at 48 V AC AC / DC operated with N.O. N.C. auxiliary contacts Description AF4... AF96 contactors are mainly used for controlling -phase motors and power circuits up
Bulletin 193-T1 Bimetallic Overload Relays
Bulletin 193T1 Bimetallic Overload Relays Overload protection trip class 10 / 10A Phase loss protection Ambient temperature compensation Auxiliary contacts (1 N.O. and 1 N.C.) Manual/automatic reset mode
SafeLogic compact. Input/output module (8 inputs, 4 outputs) SLC-3-XTDS84302
Input/output module (8 inputs, 4 outputs) 2 Bosch Rexroth AG Electric Drives and Controls Input/output module (8 inputs, 4 outputs) Documentation 8 SIL3 safety inputs, 4 standard outputs, 2 configurable
Switching Power Supply
Switching Power Supply Easy-to-use Industrial Power Supply with Versatile Functions (); Power Supply Suitable for Peak Loads such as Motors and Solenoids (-P) Remote control function incorporated. Remote
CPS2000 Cabinet Power System
Input (Nominal): 90 Vac to 264 Vac (Autoranging) Output (Nominal): -48 Vdc (up to 28.8 A) and Optional 50 VA Ringing Generator The low-maintenance, outside-plant CPS2000 (Cabinet Power System) integrates
Low voltage AC drives. ABB component drives ACS to 2.2 kw / 0.25 to 3 hp Catalog
Low voltage AC drives ABB component drives ACS55 0.18 to 2.2 kw / 0.25 to 3 hp Catalog ABB component drives ABB component drives ABB component drives are designed to be incorporated into a wide variety
Power Supplies PSS Series
8 January 2009 PSS Supplies Product Description Eaton s of power supplies is designed to work in a variety of applications, including the power supply to the IT. line of power control products. They also
INDUSTRIAL POWER SUPPLIES SFL-SERIES
INDUSTRIAL POWER SUPPLIES SFL-SERIES Operating Instructions 1. Application The SFL-series are compact, rugged switching power supplies designed for applications in process automation and other industrial
IEC Limit Switches Selection Guide
IEC Limit Switches Selection Guide Limit Switches Selection Guide ABM Series ABP Series AAP Series Series ABM Series ABP Series AAP Series Prices start at Description Heavy duty IEC Double-insulated,
SYSMAC Transistor Remote Module
9 SYSMAC Transistor Remote Module Block and Transmission Capability in One Module 1 Two-conductor cable communications available using Omron Wired Remote I/O Master Modules (C200H-RM201 and C500-RM201)
PRODUCT PROFILE VARIABLE-DEPTH, FLANGE- MOUNTED DISCONNECT SWITCHES A BULLETIN 1494V
PRODUCT PROFILE BULLETIN 1494V Rockwell Automation introduces the enhanced version of Allen-Bradley Bulletin 1494V Variable-Depth, Flange-Mounted Switches that meet industrial requirements for dependable
GJL 100 A Molded Case Circuit Breaker GJL 75 A Motor Circuit Protector
GJL 100 A Molded Case Circuit Breaker GJL 75 A Motor Circuit Protector Catalog 0500CT9702R409 2009 Class 525/580 CONTENTS Description............................................. Page General Characteristics...................................
MS Application. Features. Proportional Valve Actuator General Instructions
Proportional Valve Actuator Application The Proportional Valve Actuator is a non-spring return actuator used with proportional to 10 Vdc or 4 to 0 ma controllers and standard 1/" to 1-1/4" two-way and
BR Second Position Voltages. AA Fourth Position
1336S First Position Bulletin Number BR Second Position Voltage Letter AQ BR CW A B BP BX C Q R RX W Voltages 200-240V AC or 3V DC 380-480VAC or 513-620V DC 500-600V AC or 775V DC or 200-240V AC 380-480V
Reduced Voltage Motor Starters
Reduced Voltage Motor Starters Soft Start Controllers. Solid-State Controllers Product Overview........................................ Type S70, Soft Start Controllers............................. Type
Control Circuit Protection
Contents 5SJ4 Branch Circuit Protectors 5SY4 Supplementary Protectors 5SY6 Supplementary Protectors 16/19 5SJ4 Page Selection and ordering data 1-pole up to 63A 16/4 1-pole, 2-pole, 16/5 3-pole, 240VAC
IEC Limit Switches Selection Guide
IEC Limit Switches Selection Guide Limit Switches Selection Guide ABM Series ABP Series AAP Series Series ABM Series ABP Series AAP Series Prices start at Description Heavy duty IEC Double-insulated,
JUMO dtrans p35. Pressure Sensor with IO-Link. Application. Brief description. Customer benefits. Special features
sales@jumo.co.uk info.us@jumo.net Page 1/10 JUMO dtrns p5 Pressure Sensor with IO-Link pplication Process automation Machines for the food and beverage industry General mechanical and apparatus engineering
Control and Load Switch Specifications Bulletin Number 194E, 194L
Technical Data Control and Load Switch Specifications Bulletin Number 194E, 194L Topic Page Product Line Overview 2 194E General Specifications 3 194E Approximate Dimensions 5 194L Circuit Diagrams 13
Series L9 UL-489 Miniature Circuit Breakers
Series UL-489 iniature Breakers Industrial Breakers for Branch up to 40 Amps Sprecher+Schuh includes a line of circuit breakers approved for branch circuit applications in the United States and Canada
System pro M compact Miniature Circuit Breaker SU200M for branch circuit protection acc. to UL 489
System pro M compact Miniature Circuit Breaker SU200M for branch circuit protection acc. to UL 489 2CDC021004S0014 2CDC021046S0014 The miniature circuit breaker SU 200 M is ABB s solution for UL 489 branch
AF09... AF30 3-pole Contactors up to 25 HP / 600 VAC
AF09... AF0 -pole Contactors up to 25 HP / 600 VAC Contactors and Overload Relays Overview.../0 AF09... AF0 -pole Contactors.../2 Main Technical Data.../8 Main Accessory Fitting Details.../2 Main Accessory.../24
Instructions Contact numbers to EN Coil terminal markings to EN Integrated diode-resistor combination Coil rating 2.
Deliveryprogram Contactorrelay,2N/O+2N/C,DCcurrent Partno. DILER-22-G(220VDC) Articleno. 010091 CatalogNo. XTRM10A22BD Product range DILER Mini-contactors Application Contactor relays Description with
GETTING STARTED GUIDE NI AO, ±10 V, 16 Bit, 25 ks/s/ch Simultaneous
GETTING STARTED GUIDE NI 9264 16 AO, ±10 V, 16 Bit, 25 ks/s/ch Simultaneous This document explains how to connect to the NI 9264. In this document, the NI 9264 with spring terminal and the NI 9264 with
Compact Circuit Protector (CCP)
UL Class CC, Midget and IEC 10x38 fuses The revolutionary Cooper Bussmann CCP is 1/3 the footprint of a molded case circuit breaker. The level of protection provided by the CCP is up to three times the
Model Number Structure
Solid State Relays Extremely Thin Relays Integrated with Heat Sinks Downsizing achieved through optimum design of heat sink. Mounting possible via screws or via DIN track. Close mounting possible for linking
Model Number Structure
Solid State Relays CSM DS_E_2_2 Extremely Thin Relays Integrated with Heat Sinks Downsizing achieved through optimum design of heat sink. Mounting possible via screws or via DIN track. Close mounting possible
Redundant Control System
Redundant Control System Safety instrumented system applications up to SIL 3 Process reliability Process valve diagnostics COMPLETE FUNCTIONAL SAFETY WITH ENHANCED RELIABILITY The Redundant Control System
DATASHEET - ZB Delivery program. Overload relay, 50-65A, 1N/O+1N/C. Catalog No Eaton Catalog No. XTOB065DC1 EL-Nummer
DATASHEET - ZB65-65 Delivery program Overload relay, 50-65A, 1N/O+1N/C Part no. ZB65-65 Catalog No. 278460 Eaton Catalog No. XTOB065DC1 EL-Nummer 0004131855 (Norway) Product range Overload relay ZB up
Open Frame Power Supplies
, 0 300 Watt Features Small and compact PCB Construction Optional with Chassis and Cover Universal Input 8 264 VAC, Output Voltage adjustable Compliance to E 6000-3-2 (PFC) EMI meets E022, Class B and
VA-640GSX024P. Overview. Applications. Features & Benefits. Datasheet. Large Globe Valve Actuators
VA-640GSX024P Datasheet Large Globe Actuators Overview The VA-640GSX024P Electronic valve actuators receive a 0 to 10 VDC or 4 to 20 ma control signal to proportionally control the valve. Applications
(with Class-1 AC resistive load) 3. G3PB-215B-2N-VD kW max. (25 A) G3PB-225B-3N-VD 2. G3PB-225B-2N-VD kw max. (35 A) G3PB-235B-3N-VD 2
Solid-state Contactor (New Heat Sink Construction) G3PB Space and working time saved with new heat sink construction. Series now includes 480-VAC models to allow use in a greater range of applications.
1370 DC Loop Contactors and Lug Kits
Installation Instructions 1370 DC Loop Contactors and Lug Kits 1370 DC Contactors are electromagnetically held contactors specially designed to switch the armature current from a DC drive module to a shunt
Compact Heat Meters. Features. -A Pulsed output. -B M-Bus output. Accessories. UK Sales Tel: International Tel:
Compact Heat Meters Features Compact design Simple operation Pulsed output Measures heating or cooling Specification Product Codes Water Meter Temp. range 10 to 90 C Nominal pressure 16bar Installation
MP-Series Integrated Gear Motors
Installation Instructions MP-Series Integrated Gear Motors (Catalog Numbers: MPG-A004-031, MPG-A004-091, MPG-A010-031, MPG-A010-091, MPG-B010-031, MPG-B010-091, MPG-A025-031, MPG-A025-091, MPG-B025-031,
Selection Guide. Control Circuit and Load Protection
Selection Guide Control Circuit and Load Protection Circuit Protection Portfolio 1489-M Circuit Breakers Approved for branch circuit protection in the United States and Canada, and certified as Miniature
ABB component drives ACS150, 0.5 to 5 Hp
ABB component drives ACS150, 0.5 to 5 Hp Technical Catalog BUSINESS PROFILE INDUSTRIES PRODUCTS APPLICATIONS EXPERTISE PARTNERS SERVICES Contents Choice 1: Simply contact your local ABB drives sales office
Brushless DC Motor Systems FBL2 Series
FBL2 Series The FBL2 Series consists of a high performance, compact, brushless DC motor and driver. This product is available with 75 W (1/1 HP) and 12 W (1/6 HP) output power. For easy installation, the
OpenAir Electronic Damper Actuators GLB Series Enhanced Non-spring Return Rotary
Document No. 155-785 OpenAir Electronic Damper Actuators GLB Series Enhanced Non-spring Return Rotary Description The OpenAir direct coupled enhanced non-spring return rotary electric actuators are designed