VIKING HEAVY DUTY PUMPS
|
|
- Kristopher Welch
- 5 years ago
- Views:
Transcription
1 SERIES 495 STANDARD CONSTRUCTION Section 44 Page 44. Issue D FEATURES Range Temperature Range Viscosity Range 250 PSI (7 BAR) for 00 SSU ( cst) and above 50 PSI (0 BAR) for 8 to 00 SSU ( cst to cst) 00 PSI (7 BAR) for below 8 SSU ( cst) - 40 F. to + 50 F. (- 40 C. to + 77 C.) 28 SSU to 5,000 SSU (0. cp to,00 cst) SERIES 495 s Cutaway View AS, AK, AL SERIES 495 s Cutaway View G, GG, H, HJ, HL GPM up to 75 (M³/Hr up to 7) 2 (Nomal Ratg) BALL BEARINGS (Standard Equipment) s are equipped with ner casg ball bearg stalled outside of mechanical seal and a radial thrust ball bearg permittg heavy-duty service up to 250 PSI (7 BAR). Beargs are Sealed for Life. PRESSURE LUBRICATION (Standard Equipment) ( AS, AK, AL Sizes) A patented pressure lubrication system automatically lubricates the idler bushg. This system provides a constant film of liquid between the idler bushg and idler p at a pressure equal to the pump discharge pressure regardless of pump rotation. DUCTILE IRON PARTS (Standard Equipment) ( AS, AK, AL Sizes) Internal pumpg gears (rotor and idler) are constructed of ductile iron for added strength handlg all types of liquids up to 5,000 SSU (,00 cst). HL size rotor also furnished ductile iron. O-RING GASKETS (Standard Equipment) O-Rg gaskets are used between casg and head plate and between casg and relief valve or valve plates. Flat valve gaskets furnished on G, GG, H, HJ and HL size pumps. These gaskets provide a positive seal elimatg a chance for leakage at these pots. Vikg s high-speed, heavy-duty Series 495 pumps are available capacities up to 75 GPM. These pumps can be furnished directly connected to a 50 Hz or 60 Hz motor. (See Series 495D units shown on page 44..) All eight sizes of Vikg Series 495 pumps are furnished with sgle mechanical seals. This seal is a simple selfadjustg, non-leak method of shaft sealg located ahead of the casg ball bearg. The Series 495 pumps are built for con tuous or termittent duty for such applications as filterg, circulatg, transferrg, or booster service general dustrial, petroleum and mare uses. NOTE: UL listed pumps for handlg flammable liquids require special construction. Externals are high strength cast iron. (Ductile Iron Casg on AS, AK and AL sizes). See Catalog Section 440 for details and pricg formation. Model numbers for these pumps must be designated by a suffix -F, eg. GG495-F or when used with a D drive, GG495D-F. UL listed models must be equipped with either an ternal or return-to-tank safety relief valve. discharge pressure for UL listed models is 25 PSIG. Values shown represent mimums or maximums. Some special construc tion or consideration may be required before a cataloged pump can be ap plied to an application volvg maximum pressure or mimum or max imum temperature and/or viscosity. Certa models have restrictions pressures and/or viscosities. See specifications, page 44.2, and perform ance curves. 2 Nomal capacities based on handlg th liquids. Metric conversions are based on US measurements and rounded to the nearest whole number. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 09
2 Section 44 Page 44.2 Issue E VIKING HEAVY DUTY PUMPS SERIES 495 STANDARD CONSTRUCTION MECHANICAL SEAL Buna-N bellows. 2 Buna-N O-rg. Carbon rotatg face (washer). 4 Ni-Resist stationary seat. 5 metal parts. 6 Staless steel sprg. SERIES 495 s G, GG, H, HJ and HL Sizes In addition to the famous features listed on the previous page, Series 495 heavy-duty pumps are furnished with an tegral relief valve as shown the pump photos above. Return-to-tank valves are also available on all models on request. Note: On the G, GG, H, HJ and HL sizes, the valve mounts on the pump head. The AS, AK and AL size value mounts on top of the pump casg. All sizes equipped with Buna-N mechanical seal with carbon rotatg and Ni-Resist stationary faces. SERIES 495 s AS, AK and AL Sizes Dimensions for Unmounted s See Page Performance Data for Unmounted s See Pages 44. through CONSTRUCTION SERIES 495 ( GG THROUGH AL SIZES) Standard Construction Models Casg Head Rotor Idler Rotor Shaft and Idler P Idler Bushg Internal Safety Relief Valve G495, GG495 H495, HJ495 Iron Iron 2 Iron Iron Carbon Graphite Iron HL495 Iron Iron Ductile Iron Iron Carbon Graphite Iron AS495, AK495, AL495 Iron Iron Ductile Iron Ductile Iron Carbon Graphite Iron SPECIFICATION Model Port Size (NPT) G495 GG495 H495 HJ495 HL495 Nomal Capacity at Rated Speed 22 cst (00 SSU) Liquid 4 60 Hz Motor Speed Standard Buna-N seal from - F. to +. (-29 C. to +07 C.) With special GG size has steel idler. construction, temperatures from -40 F. to +50 F. (-40 C. to +77 C.) can be handled 4 Nomal capacities based on handlg th liquids. with this series. 5 For viscosities above 5,000 SSU (,00 cst), provide details for recommendations. 2 When steel fitted construction is required, GG will have steel rotor, HJ will have ductile 6 These models have ductile iron rotors; steel fitted rotors not necessary. iron rotor. 7 If suction pressure exceeds 00 PSIG (7 BAR), consult factory. Metric conversions are based on US measurements and rounded to the nearest whole number. 50 Hz Motor Speed 7 Hydrostatic Fitted Construction Above This Viscosity 5 Temperature VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 09 Approximate Shippg Weight Inch GPM RPM M³/hr RPM PSI (BAR) PSI BAR SSU (cst) Deg. F Deg. C Lb. Kg AS495 2½ 5 AK495 2½ 50 AL (69) (69) (5500) (69)
3 SERIES 495 STANDARD CONSTRUCTION DIRECT DRIVE UNITS ( D DRIVE) Section 44 Page 44. Issue E SERIES 495 s with D Drive AS, AK and AL Sizes SERIES 495 s with D Drive G, GG, H, HJ and HL Sizes Series 495 pumps the G, GG, H, HJ and HL size are designed for high-speed, heavy-duty service. The pump is connected by a flexible couplg with guard directly to a 50 Hz or 60 Hz motor. See series 495D chart below. Both pump and motor mount on a sturdy formed steel base. This makes a very compact, rugged unit for heavy-duty ser vice, handlg many types of fluids up to 5,000 SSU (,00 cst). The three large size Series 495D direct connected units all feature the 495 high-speed pump connected by a flexible couplg with guard to 50 Hz or 60 Hz motor. See chart below. Both pump and motor are mounted on a heavy-duty formed steel base. The three larger sizes are equipped with ductile iron pump gears (rotor and idler). O-Rg head and valve gaskets, mechanical seals and automatic pressure lubrication systems are also standard construction. These pumps are also available with steel externals, see Section 54. Dimensions for D Drive See Page Performance Data for D Drive See Pages 44. through SPECIFICATIONS D DRIVE UNITS Model Port Size (NPT) G495D GG495D H495D HJ495D HL495D Nomal Capacity at Rated Speed 22 cst (00 SSU) Liquid 60 Hz Motor Speed 50 Hz Motor Speed 5 Hydrostatic Fitted Construction Above This Viscosity Temperature 2 Approximate Shippg Weight Inch GPM RPM M³/hr RPM PSI (BAR) PSI BAR SSU (cst) Deg. F Deg. C Lb. Kg AS495D 2½ 5 AK495D 2½ 50 AL495D (69) (69) (5500) (69) Nomal capacities based on handlg th liquids. 2 With special construction, temperatures to + 50 F. (77 C.) can be handled with this series. For viscosities above 5,000 SSU (,00 cst), provide details for recommendations. 4 These models have ductile iron rotors; steel fitted rotors not necessary. 5 If suction pressure exceeds 00 PSIG (7 BAR), consult factory. Metric conversions are based on US measurements and rounded to the nearest whole number. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 09
4 Section 44 Page 44.4 Issue E VIKING HEAVY DUTY PUMPS SERIES 495 STANDARD CONSTRUCTION FLANGE BRACKET Range Temperature Range 250 PSI (7 BAR) for 00 SSU ( cst) and above 50 PSI (0 BAR) for 8 to 00 SSU ( cst to cst) 00 PSI (7 BAR) for below 8 SSU ( cst) - 40 F. to + 50 F. (- 40 C. to + 76 C.) SERIES 495 s G, GG, H, HJ and HL Sizes SERIES 495 s AS, AK and AL Sizes Series 495 pumps are similar to the Series 495 on precedg pages with the exception of a flange bracket mount casg. CONSTRUCTION SERIES ( GG THROUGH AL SIZES) Standard Construction Models Mountg Bracket (Units Only) Casg Head Rotor Idler Rotor Shaft and Idler P Idler Bushg Internal Safety Relief Valve G495, GG495 H495, HJ495 Iron Iron Iron 6 Iron 7 Iron Carbon Graphite Iron HL495 Iron Iron Iron Ductile Iron Iron Carbon Graphite Iron AS495, AK495, AL495 Iron Iron Iron Ductile Iron Ductile Iron Carbon Graphite Iron SPECIFICATION Model Port Size (NPT) G495 GG495 H495 HJ495 HL495 Metric conversions are based on US measurements and rounded to the nearest whole number. Nomal Capacity at Rated Speed 22 cst (00 SSU) Liquid Hz Motor Speed 50 Hz Motor Speed Viscosity Range 28 SSU to 5,000 SSU (0. cp to,00 cst) GPM up to 75 (M³/Hr up to 7) 4 (Nomal Ratg) All eight sizes are furnished with sgle mechanical seals, cludg Buna-N elastomer gaskets. Standard construction features ternal type safety relief valve on pump head or casg (dependg on pump size), O-Rg head and valve gaskets, and automatic pressure lubrication system on the three larger size pumps. The 495 series offers an optional flange port for sizes H-AL. Contact the factory for details. Dimensions for Unmounted s See Page Performance Data for Unmounted s See Pages 44. through Hydrostatic Fitted Construction Above This Viscosity Temperature 2 VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 09 Approximate Shippg Weight Inch GPM RPM M³/hr RPM PSI (BAR) PSI BAR SSU (cst) Deg. F Deg. C Lb. Kg AS495 2½ 5 AK495 2½ 50 AL Consult factory for specific recommendations. 2 Standard Buna-N seal from - F. to +. (-29 C. to +07 C.) With special construction, temperatures from -40 F. to +50 F. (-40 C. to +77 C.) can be handled with this series. For viscosities above 5,000 SSU (,00 cst), provide details for recommendations. 4 Nomal capacities based on handlg th liquids (69) (69) (5500) (69) Buna-N elastomer used mechanical seal of Series 495 pumps. 6 When steel fitted construction is required, GG will have steel rotor, HJ will have ductile iron rotor. 7 GG size has steel idler. 8 These models have ductile iron rotors; steel fitted rotors not necessary. 9 If suction pressure exceeds 00 PSIG (7 BAR), consult factory.
5 SERIES 495 STANDARD CONSTRUCTION FLANGE BRACKET MOUNTED UNITS ( M DRIVE) Section 44 Page 44.5 Issue F SERIES 495 s with M Drive G, GG, H, HJ and HL Sizes SERIES 495 s with M Drive AS, AK and AL Sizes For a compact horizontal mountg, the face mounted 495M heavy-duty pump units all eight sizes clude a combation motor C flange and square pump flange bracket with couplg connectg motor and pump. The three larger size pumps are equipped with ductile iron pump gears (rotor and idler) and automatic pressure lubrication system. All sizes have O-Rg head and valve gaskets and mechanical seals as standard construction. These pumps are also available with steel externals, see Section 54. Dimensions for M Drive See Page 44.9 and Performance Data for M Drive See Pages 44. through SPECIFICATIONS M DRIVE UNITS Model Port Size (NPT) G495M GG495M H495M HJ495M HL495M Nomal Capacity at Rated Speed 22 cst (00 SSU) Liquid 60 Hz Motor Speed 50 Hz Motor Speed 5 Hydrostatic Fitted Construction Above This Viscosity Temperature 2 Approximate Shippg Weight Inch GPM RPM M³/hr RPM PSI (BAR) PSI BAR SSU (cst) Deg. F Deg. C Lb. Kg AS495M 2½ 5 AK495M 2½ 50 AL495M (69) (69) (5500) (69) Nomal capacities based on handlg th liquids. 2 With special construction, temperatures to + 50 F. (77 C.) can be handled with this series. For viscosities above 5,000 SSU (,00 cst), provide details for recommendations. 4 These models have ductile iron rotors; steel fitted rotors not necessary. 5 If suction pressure exceeds 00 PSIG (7 BAR), consult factory. Metric conversions are based on US measurements and rounded to the nearest whole number. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 09
6 Section 44 Page 44.6 Issue C VIKING HEAVY DUTY PUMPS SERIES 495 STANDARD CONSTRUCTION DIMENSIONS These dimensions are average and not for construction purposes. Certified prts on request. For specifications, see page SERIES 495 G GG H HJ HL SIZES MODEL NO. A B D E F G H J K L M N O P S T U V W X G495 GG495 H495 HJ495 HL FLAT mm x mm x For specifications, see page SERIES 495 AS AK AL SIZES MODEL NO. AS495 AK495 AL495 A B D E F G H J K L M N O P S T U V W X Y Z x ½ mm x x ½ mm x x mm x VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 09
7 Section 44 SERIES 495 STANDARD CONSTRUCTION DIMENSIONS These dimensions are average and not for construction purposes. Certified prts on request. Page 44.7 Issue C For specifications, see page 44.. SERIES 495 ( D DRIVE) G GG H HJ HL AS AK AL SIZES MODEL NO. A B D E F H J K L M M N P S 56 frame motors (short base). (Available with G & GG size pumps.) 2 4T and 45T frame motors (long base). (Available with G & GG size pumps.) 56, 4T and 45T frame motors. (Available with H, HJ or HL size pumps.) 4 82, 82T, 84, 84T frame motors. (Available with H through AL size pumps.) 5 2, 2T, 25, 25T frame motors. (Available with H through AL size pumps.) 6 254U, 254T, 256U, 256T frame motors. (Available with AK through AL size pumps.) 7 Dimensions cludes motor block, base height is. 8 Dimension cludes motor block, base height is 2 ¹⁵ ₁₆. NOTE: All AS, AK, AL pump sizes available with any of the three motors shown columns. G495D GG495D H495D HJ495D HL495D AS495D AK495D AL495D mm mm mm mm mm ½ mm ½ mm mm VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 09
8 Section 44 Page 44.8 Issue C VIKING HEAVY DUTY PUMPS SERIES 495 STANDARD CONSTRUCTION DIMENSIONS These dimensions are average and not for construction purposes. Certified prts on request. For specifications, see page SERIES 495 G GG H HJ HL SIZES MODEL NO. A B C E F G H J K N P R T U V X G495 GG495 H495 HJ495 HL FLAT mm x mm x For specifications, see page SERIES 495 AS AK AL SIZES MODEL NO. A B C E F G H J K L P R S T U V W X Y Z AS495 AK ½ mm x AL mm x VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 09
9 SERIES 495 STANDARD CONSTRUCTION DIMENSIONS These dimensions are average and not for construction purposes. Certified prts on request. Section 44 Page 44.9 Issue D For specifications, see page SERIES 495 ( M DRIVE) NEMA C G GG H HJ HL SIZES NOTE: Jaw type couplg with straight jaws recommended to facilitate assembly of motor and pump to bracket. COUPLING IS GUARDED WITH PLATES OVER SIDE OPENINGS ON MOUNTING BRACKET. MODEL NO. A B C J L M N MOTOR FRAME D E F G H K SLOT 56C mm TC mm G495M TC mm GG495M TC mm TC mm SLOT 56C mm TC mm H495M HJ495M HL495M TC mm TC mm TC mm TC mm TC mm For specifications, see page SERIES 495 ( M DRIVE) NEMA C AS AK AL SIZES Dimensions are correct for 82TC through 25TC motors. For 254TC/256TC motors, add.88 to the dimensions shown. NOTE: Jaw type couplg with straight jaws recommended to facilitate assembly of motor and pump to bracket. COUPLING IS GUARDED WITH PLATES OVER SIDE OPENINGS ON MOUNTING BRACKET. MODEL NO. A B C D E F G H J K ➀ L M N O P R S Y AS495M AK495M AL495M ½ mm mm VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 09
10 Section 44 Page 44.0 Issue C VIKING HEAVY DUTY PUMPS SERIES 495 STANDARD CONSTRUCTION For specifications, see page SERIES 495 ( M DRIVE) IEC Frame H HJ HL SIZES Brackets are designed for IEC motors with B4 mountg face. NOTE: Jaw type couplg with straight jaws recommended to facilitate assembly of motor and pump to bracket. COUPLING IS GUARDED WITH PLATES OVER SIDE OPENINGS ON MOUNTING BRACKET. MODEL NO H495M HJ495M HL495M A B C M N P MOTOR FRAME D E F G H J K L O R S IEC 90 mm IEC 00/2 mm mm IEC VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 09
11 SERIES 49 AND 49 STEEL EXTERNALS FEATURES Section 54 Page 54. Issue B Range 2 Temperature Range Viscosity Range 250 PSI (7 BAR) for 00 SSU ( cst) and above 50 PSI (0 BAR) for 8 to 00 SSU ( cst to cst) 00 PSI (7 BAR) for below 8 SSU ( cst) 0 F. to + 50 F. (- 8 C. to + 76 C.) 28 SSU to 5,000 SSU (0. cp to,00 cst) GPM (m³/hr ) 4 (Nomal Ratg) FEATURES MECHANICAL SEAT Buna-N Bellows 2 Buna-N O-rg Carbon Rotatg Face (Washer) 4 Ni-Resist Stationary Seat 5 Metal Parts 6 Staless Sprg SERIES 49 Cutaway View 0--0 GPM Sizes ( m³/hr) BALL BEARINGS (Standard Equipment) s are equipped with ner casg ball bearg stalled outside of mechanical seal and a radial thrust ball bearg permittg heavy-duty service up to 250 PSI (7 BAR). Beargs are Sealed for Life. INTEGRAL OVER-PRESSURE RELIEF VALVE (Standard Equipment) Permits bypassg of liquid from discharge to suction side of pump. Prevents build up of pressure discharge le. GG, HJ and HL size valve mounts on pump head. AS, AK and AL size valve mounts on pump casg. DUCTILE IRON PARTS (Standard Equipment) ( AS, AK, AL Sizes) Internal pumpg gears (rotor and idler) are constructed of ductile iron for added strength handlg all types of liquids up to 5,000 SSU (,00 cst). HL size rotor also furnished ductile iron. O-RING GASKETS (Standard Equipment) O-Rg gaskets are used between casg and head plate and between casg and relief valve or valve plates. Flat valve gaskets furnished on GG. HJ and HL size pumps. These gaskets provide a positive seal elimatg a chance for leakage at these pots. Vikg s high-speed, heavy-duty Series 49 and 49 steel external pumps are available capacities of 0,, 0, 5, 50 and 75 GPM. The three smaller size pumps can be furnished directly connected to either or RPM motors, the three larger sizes directly connected to RPM motors. Series 49 is designed for vertical or horizontal flange mount stallations where space is at a premium. (See pages ) Series 49 is designed for foot type horizontal mountg. These pumps are built for contuous or termittent duty for such applications as filterg, circulatg, transferrg, or booster service general dustrial, petrochemical and other dustries. They are furnished as standard with mechanical seal construction to mimize liquid loss and for shaft protection. The thrust control provides micrometer adjustments for accurate rotor and shaft positiong to help you keep operatg with new-pump efficiency through years of heavy-duty service. Vikg s famous gear-with-a-gear prciple has only two movg parts. It is the secret of dependable efficient operation of all positive displacement Vikg rotary pumps. Positive displacement of liquid is accomplished by the meshg of rotor and idler gear teeth. With every revolution of the pump shaft, a defite amount of liquid is drawn to the pump through the suction port. Consult factory for specific recommendations. 2 With special construction, temperature to + 50 F. can be handled with this series. For viscosities above 5,000 SSU (,00 cst), provide details for recommendations. 4 Nomal capacities based on handlg th liquids at RPM on three small sizes, RPM on three large sizes. Metric conversions are based on US measurements and rounded to the nearest whole number. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 05
12 Section 54 Page 54.2 Issue B VIKING HEAVY DUTY PUMPS SERIES 49 STEEL EXTERNALS FOOT MOUNT WITH FLANGED PORTS SERIES 49 s GG, HJ and HL Sizes SERIES 49 s AS, AK and AL Sizes Vikg s positive displacement Series 49 pump le with steel externals is ideal for refg, petrochemical and other applications requirg shock resistant construction. They are equipped with steel, ternal type, over-pressure relief valve. The steel used meets ASTM designation A26 Grade WCB specifications. All pumps are equipped with horizontal 00 lb. ANSI flanged ports and conform to most requirements of API 676. A simple, efficient, unbalanced sgle mechanical seal with Buna-N gaskets, carbon and Ni-Resist faces is standard. Other seal types and materials available on request. For handlg viscosities above 5,000 SSU, refer to Series 2A pumps, Catalog Section 60. Dimensions for Unmounted s See Page Performance Data for Unmounted s See Pages 54. through CONSTRUCTION SERIES 5 49 ( GG THROUGH AL SIZES) Standard Construction Models Casg Head Rotor Idler GG49 HJ49 Rotor Shaft and Idler P 6 Iron 7 Iron HL49 AS49 AK49 AL49 Ductile Iron Ductile Iron Iron Ductile Iron Idler Bushg Carbon Graphite Carbon Graphite Carbon Graphite Internal Safety Relief Valve Externals Externals Externals SPECIFICATION Model Numbers 00 lb. ANSI Flanged Port Size 4 Nomal Ratg Hydrostatic 8 Discharge 2 Temperature Fitted Construction Above This Viscosity Approximate Shippg Weight With Valve (Less Power) Unmounted Inches GPM (m³/hr) RPM PSIG (BAR) PSIG (BAR) Degrees SSU (cst) Pounds (KG) GG49 HJ49 HL () (2) () (7) AS (8) AK () AL49 75 (7) Consult factory for specific recommendations. 2 With special construction, temperatures to + 50 F. can be handled with this series. For viscosities above 5,000 SSU (,00 cst), provide details for recommendations. 4 Nomal capacities based on handlg th liquids at RPM on three small sizes, RPM on three large sizes. 5 Buna-N elastomer used mechanical seal of Series 49 pumps. Metric conversions are based on US measurements and rounded to the nearest whole number. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA (69) 25 () 7500 (69) 50 (2) 9 50 (2) 9 00 (45) 9 00 (45) 9 02 (46) 6 When steel fitted construction is required, GG will have steel rotor, HJ will have ductile iron rotor. 7 GG size has steel idler. 8 If suction pressure exceeds 00 PSIG (7 BAR), consult factory. 9 These models have ductile iron rotors; steel fitted rotors not necessary. 0 Models AS and AK have 2½ cored openg.
13 SERIES 49 STEEL EXTERNALS DIRECT DRIVE UNITS ( D DRIVE) Section 54 Page 54. Issue B SERIES 49 s with D Drive AS, AK and AL Sizes SERIES 49 s with D Drive GG, HJ and HL Sizes Series 49 units the GG, HJ and HL size (nomal ratg 0,, 0 GPM) are designed for highspeed, heavy-duty service. The pump is connected by a flexible couplg with guard directly to a or RPM motor. Both pump and motor mount on a sturdy formed steel base. This makes a very compact, rugged unit for heavy-duty service, handlg many types of liquids up to 5,000 SSU. The three large-size Series 49D direct connected units all feature the 49 high-speed pump connected by a flexible couplg with guard to RPM motor. Both pump and motor are mounted on a heavy-duty formed steel base. The three larger sizes are equipped with ductile iron pump gears (rotor and idler). Flat or O-Rg head and valve gaskets, mechanical seals and automatic pressure lubrication systems are also standard construction. Dimensions for D Drive See Page Performance Data for D Drive See Pages 54. through SPECIFICATIONS D DRIVE UNITS Model Numbers 00 lb. ANSI Flanged Port Size Nomal Ratg Hydrostatic 2 Discharge Temperature VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 05 4 Fitted Construction Above This Viscosity Approximate Shippg Weight With Valve (Less Power) Unmounted Inches GPM (m³/hr) RPM PSIG (BAR) PSIG (BAR) Degrees SSU (cst) Pounds (KG) GG49D HJ49D HL49D () (2) () (7) AS49D 6 5 (8) AK49D 6 50 () AL49D 75 (7) Nomal capacities based on handlg th liquids at RPM on three small sizes, RPM on three large sizes. 2 If suction pressure exceeds 00 PSIG (7 BAR), consult factory. With special construction, temperatures to + 50 F. can be handled with this series. Metric conversions are based on US measurements and rounded to the nearest whole number (69) 5 (2) 7500 (69) 75 (4) 5 75 (4) 5 20 (04) 5 20 (04) 5 25 (07) 4 For viscosities above 5,000 SSU (,00 cst), provide details for recommendations, or see Series 2A, Catalog Section These models have ductile iron rotors; steel fitted rotors not necessary. 6 Models AS and AK have 2½ cored openg.
14 Section 54 Page 54.4 Issue B VIKING HEAVY DUTY PUMPS SERIES 49 STEEL EXTERNALS VERTICAL OR HORIZONTAL FLANGE BRACKET MOUNT SERIES 49 s GG, HJ and HL Sizes Range 2 Temperature Range Viscosity Range 250 PSI (7 BAR) for 00 SSU ( cst) and above 50 PSI (0 BAR) for 8 to 00 SSU ( cst to cst) 00 PSI (7 BAR) for below 8 SSU ( cst) 0 F. to + 50 F. (- 8 C. to + 76 C.) 28 SSU to 5,000 SSU (0. cp to,00 cst) SERIES 49 s AS, AK and AL Sizes CONSTRUCTION SERIES 5 49 ( GG THROUGH AL SIZES) Standard Construction Models GPM (m³/hr ) 4 (Nomal Ratg) This Flange Bracket Mount Series 49 pump le with steel externals is ideal for refg, mare, petrochemical and other applications requirg shock resistant construction. They are equipped with steel flange-mount casg and are furnished with (Units only) Mountg Bracket Casg Head Rotor Idler steel, ternal type, over-pressure relief valve. The steel used meets ASTM designation A26 Grade WCB specifications. All pumps are equipped with horizontal 00 lb. ANSI flanged ports and conform to most requirements of API 676. A simple, efficient, unbalanced sgle mechanical seal with Buna-N gaskets, carbon and Ni-Resist faces is standard. Other seal types and materials available on request. For handlg viscosities above 5,000 SSU, refer to Series 2A pumps, Catalog Section 60. Consult factory or Vikg representative. Dimensions for Unmounted s See Page 54.8 and Performance Data for Unmounted s See Pages 54. through Rotor Shaft and Idler P Bushg Internal Safety Relief Valve GG49 HJ49 Iron 6 Iron 7 Iron Carbon Graphite Externals HL49 Iron Ductile Iron Iron Carbon Graphite Externals AS49 AK49 AL49 Iron Ductile Iron Ductile Iron Carbon Graphite Externals SPECIFICATIONS Model Numbers 00 lb. ANSI Flanged Port Size 4 Nomal Ratg Hydrostatic 8 Discharge 2 Temperature Fitted Construction Above This Viscosity VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 05 Approximate Shippg Weight With Valve Unmounted Unmounted Inches GPM (m³/hr) RPM PSIG (BAR) PSIG (BAR) Degrees SSU (cst) Pounds (KG) GG49 HJ49 HL () (2) () (7) AS (8) AK () AL49 75 (7) Consult factory for specific recommendations. 2 With special construction, temperatures to + 50 F. can be handled with this series. For viscosities above 5,000 SSU (,00 cst), provide details for recommendations. 4 Nomal capacities based on handlg th liquids at RPM on three small sizes, RPM on three large sizes. 5 Buna-N elastomer used mechanical seal of Series 49 pumps (69) 8 (8) 7500 (69) 40 (8) 9 40 (8) 9 80 (6) 9 80 (6) 9 8 (7) 6 When steel fitted construction is required, GG will have steel rotor, HJ will have ductile iron rotor. 7 GG size has steel idler. 8 If suction pressure exceeds 00 PSIG (7 BAR), consult factory. 9 These models have ductile iron rotors; steel fitted rotors not necessary. 0 Models AS and AK have 2½ cored openg. Metric conversions are based on US measurements and rounded to the nearest whole number.
15 SERIES 49 STEEL EXTERNALS FLANGE BRACKET VERTICAL INLINE MOUNTED PUMPS ( IM DRIVE) Section 54 Page 54.5 Issue B Vikg s Series 49 pump le can be mounted either vertically or horizontally to electric motors. Vertical le mounted unit described on this page comes complete with C flange mountg bracket and couplg between motor and pump. Ideal for refg, petrochemical, mare and other applications requirg shock resistant construction, these units save space and weight. They are equipped with steel casg and head and are furnished with steel, ternal type, over-pressure relief valve. The steel used meets ASTM designation A26 Grade WCB specifications. All pumps are equipped with opposite 00 lb. ANSI flanged ports. They also conform to most requirements of API 676. A simple, efficient, unbalanced sgle mechanical seal with Buna-N gaskets, carbon and Ni-Resist faces is standard. Dimensions for Mounted Units See Page Performance Data for Mounted Units See Pages 54. through SERIES 49 s VIKING VERTICAL Inle mounted unit with IM Drive Optional mountg arrangement allows easy pump removal without disturbg pipg or motor. Consult factory. ( IOM Drive) SPECIFICATIONS IM DRIVE UNITS Model Numbers 00 lb. ANSI Flanged Port Size Nomal Ratg Hydrostatic 2 Discharge Temperature VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 05 4 Fitted Construction Above This Viscosity Approximate Shippg Weight With Valve Unmounted Mounted Unit Inches GPM (m³/hr) RPM PSIG (BAR) PSIG (BAR) Degrees SSU (cst) Pounds (KG) GG49IM HJ49IM HL49IM () (2) () (7) AS49IM 6 5 (8) AK49IM 6 50 () AL49IM 75 (7) Nomal capacities based on handlg th liquids at RPM on three small sizes, RPM on three large sizes. 2 If suction pressure exceeds 00 PSIG (7 BAR), consult factory. With special construction, temperatures to + 50 F. can be handled with this series. Metric conversions are based on US measurements and rounded to the nearest whole number (69) 28 () 7500 (69) 50 (22) 5 50 (22) 5 0 (50) 5 0 (50) 5 2 (5) 4 For viscosities above 5,000 SSU (,00 cst), provide details for recommendations, or see Series 2A, Catalog Section These models have ductile iron rotors; steel fitted rotors not necessary. 6 Models AS and AK have 2½ cored openg.
16 Section 54 Page 54.6 Issue B VIKING HEAVY DUTY PUMPS SERIES 49 STEEL EXTERNALS FLANGE BRACKET HORIZONTAL MOUNTED PUMPS ( M DRIVE) SERIES 49 s with M Drive GG, HJ and HL Sizes SERIES 49 s with M Drive AS, AK and AL Sizes For more compact horizontal mountg, the C flange mounted Series 49 Heavy-Duty pump units all six sizes clude a combation motor C flange and square pump flange bracket with couplg connectg motor and pump. The three smaller units connect to a foot mounted motor, while the three larger units clude a foot type bracket to mount a flange type motor. The three larger size pumps are equipped with ductile iron pump gears (rotor and idler) and automatic lubrication system. Flat or O-Rg head and valve gaskets and mechanical seals are standard construction. The steel used meets ASTM designation A26 Grade WCB specifications. All pumps are equipped with horizontal 00 lb. ANSI flanged ports and conform to most requirements of API 676. Dimensions for D Drive See Page Performance Data for Unmounted s See Pages 54. through SPECIFICATIONS M DRIVE UNITS Model Numbers 00 lb. ANSI Flanged Port Size Nomal Ratg Hydrostatic 2 Discharge Temperature 4 Fitted Construction Above This Viscosity VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 05 Approximate Shippg Weight With Valve (Less Power) Mounted Unit Inches GPM (m³/hr) RPM PSIG (BAR) PSIG (BAR) Degrees SSU (cst) Pounds (KG) GG49M HJ49M HL49M () (2) () (7) AS49M 6 5 (8) AK49M 6 50 () AL49M 75 (7) Nomal capacities based on handlg th liquids at RPM on three small sizes, RPM on three large sizes. 2 If suction pressure exceeds 00 PSIG (7 BAR), consult factory. With special construction, temperatures to + 50 F. can be handled with this series. Metric conversions are based on US measurements and rounded to the nearest whole number (69) 28 () 7500 (69) 50 (22) 5 50 (22) 5 0 (50) 5 0 (50) 5 2 (5) 4 For viscosities above 5,000 SSU (,00 cst), provide details for recommendations, or see Series 2A, Catalog Section These models have ductile iron rotors; steel fitted rotors not necessary. 6 Models AS and AK have 2½ cored openg.
17 SERIES 49 STEEL EXTERNALS DIMENSIONS These dimensions are average and not for construction purposes. Certified prts on request. Section 54 Page 54.7 Issue B For specifications, see page SERIES 49 GG HJ HL SIZES MODEL NO. A B D E F G H J K L M N 0 P S T U V W X GG49 HJ49 HL x mm x x mm x x mm x For specifications, see page SERIES 49 AS AK AL SIZES NOTE: Models AS and AK have 2½ cored openg. MODEL NO. A B D E F G H J K L M N O P S T U V W X Z AS49 AK49 AL x mm x x mm x x mm x VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 05
18 Section 54 Page 54.8 Issue B VIKING HEAVY DUTY PUMPS SERIES 49 AND 49 STEEL EXTERNALS DIMENSIONS These dimensions are average and not for construction purposes. Certified prts on request. For specifications, see page 54.. SERIES 49 ( D DRIVE) GG HJ HL AS AK AL SIZES MODEL NO. A B D E F H J K L M M N P S GG49D HJ49D HL49D AS49D AK49D AL49D mm mm mm mm mm mm mm mm frame motors (short base). (Available with GG size pump.) 2 4T and 45T frame motors (long base). (Available with GG size pump.) 56, 4T and 45T frame motors. (Available with HJ or HL size pumps.) 4 82, 82T, 84, 84T frame motors. (Available with HJ thru AL size pumps.) 5 2, 2T, 25, 25T frame motors. (Available with HJ thru AL size pumps.) 6 254U, 254T, 256U, 256T frame motors. (Available with AK thru AL size pumps.) 7 Dimensions cludes motor block, base height is. 8 Dimension cludes motor block, base height is 2 ¹⁵ ₁₆. NOTE: Models AS and AK have 2½ cored openg. NOTE: All AS, AK, AL pump sizes available with any of the three motors shown columns. For specifications, see page T P U R A-PIPE SIZE (MATE WITH 00 LB. ANSI FLANGES) N C X B B SERIES 49 GG HJ HL SIZES V-KEYWAY K H J G-HOLES E F MODEL NO. A B C E F G H J K N P R T U V X GG49 HJ49 HL x mm x x mm x x mm x VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 05
19 SERIES 49 STEEL EXTERNALS DIMENSIONS These dimensions are average and not for construction purposes. Certified prts on request. Section 54 Page 54.9 Issue B For specifications, see page SERIES 49 AS AK AL SIZES NOTE: Models AS and AK have 2½ cored openg. MODEL NO. A B C E F G H J K L P R S T U V W X Z AS49 AK mm mm x AL mm x For specifications, see page SERIES 49 VERTICAL FLANGE MOUNT INLINE UNITS ( IM DRIVE) GG HJ HL AS AK AL SIZES MODEL NO. A B C C D E MOTOR FRAME F Dimensions are correct for 82TC through 25TC motors. For 254TC/256TC motors, add.88 to the dimensions shown. NOTE: Models AS and AK have 2½ cored openg. NOTE: Jaw type couplg with straight jaws recommended to facilitate assembly of motor and pump to bracket. COUPLING IS GUARDED WITH PLATES OVER SIDE OPENINGS ON MOUNTING BRACKET. GG49IM HL49IM AS49IM AK49IM AL49IM 56C TC mm TC TC 9.56 mm TC 24 56C.2 4TC mm 45TC TC.8 mm 84TC 00 2TC 2.56 mm TC TC 84TC 2TC 25TC 254TC 6.9 mm TC 4 VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 05
20 Section 54 Page 54.0 Issue B VIKING HEAVY DUTY PUMPS SERIES 49 STEEL EXTERNALS DIMENSIONS These dimensions are average and not for construction purposes. Certified prts on request. For specifications, see page SERIES 49 ( M DRIVE) GG HJ HL SIZES MODEL NO. A B C J L M N GG49M HJ49M HL49M MOTOR FRAME D E F G H K SLOT 56C mm TC mm TC mm TC mm TC mm SLOT 56C mm TC mm TC mm TC mm TC mm TC mm TC mm NOTE: Jaw type couplg with straight jaws recommended to facilitate assembly of motor and pump to bracket. COUPLING IS GUARDED WITH PLATES OVER SIDE OPENINGS ON MOUNTING BRACKET. MODEL NO. A B AS49M AK49M AL49M C D E F G H J K mm 5 For specifications, see page mm SERIES 49 ( M DRIVE) AS AK AL SIZES Dimensions are correct for 82TC through 25TC motors. For 254TC/256TC motors, add.88 to the dimensions shown. NOTE: Models AS and AK have 2½ cored openg. NOTE: Jaw type couplg with straight jaws recommended to facilitate assembly of motor and pump to bracket. COUPLING IS GUARDED WITH PLATES OVER SIDE OPENINGS ON MOUNTING BRACKET. L M N O P R S mm VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 05
21 SERIES 497 STAINLESS STEEL FEATURES Section 64 Page 64. Issue C SERIES 497 s Cutaway View 0--0 GPM Sizes ( m³/hr) SERIES 497 s Cutaway View GPM Sizes (8--7 m³/hr) Range Temperature Range Viscosity Range 0 PSI (4 BAR) for 750 SSU (62 cst) and above 50 PSI (0 BAR) for 00 to 750 SSU ( cst to 62 cst) 00 PSI (7 BAR) for 8 SSU to 00 SSU ( cst to cst) 75 PSI (5 BAR) for below 8 SSU ( cst) 0 F. to + 50 F. (- 8 C. to + 77 C.) 0. cp to 25,000 SSU (5,500 cst) BALL BEARINGS (Standard Equipment) s are equipped with ner casg ball bearg stalled outside of mechanical seal and a radial thrust ball bearg permittg heavy-duty service up to 0 PSI (4 BAR). Beargs are Sealed for Life. MECHANICAL SEAL (Standard Equipment) All Series 497 pumps are furnished with a positive drive mechanical seal. The seal is a simple, selfadjustg, non-leak method of shaft sealg. It is especially suited for handlg liquids such as alcohols, solvents, etc. STAINLESS STEEL PUMPING ELEMENTS (Standard Equipment) Internal pumpg gears are constructed of type 6 and type 770 Staless alloy. This allows high speed, non-gallg operation, handlg all types of liquids up to 25,000 SSU (5,500 cst). PPS composite idlers are also available for th liquid applications. INTEGRAL SAFETY RELIEF VALVE (Standard Equipment) Permits bypassg of liquid from discharge to suction side of pump. Prevents build up of pressure discharge le. GG, HJ and HL size valve mounts on pump head. AS, AK and AL size valve mounts on pump casg. 2 GPM (m³/hr ) (Nomal Ratg) Vikg s heavy-duty Series 497 pumps are available capacities of 0,, 0, 5, 50 and 75 GPM. All are built for high-speed handlg of th liquids requirg staless steel construction. These pumps are ideal for such liquids as solvents, alcohols and similar liquids. The three smaller size pumps can be furnished directly connected to either or RPM motors. The three larger sizes are directly connected to RPM motors. (See Series 497D units shown on page 64..) All six sizes of Vikg Series 497 pumps are furnished with sgle mechanical seals. This seal is a simple self-adjustg, non-leak method of shaft sealg located ahead of the casg ball bearg. The Series 497 pumps are built for contuous or termittent duty for such applications as filterg, circulatg, transferrg or booster service chemical, general dustrial, petroleum and petrochemical uses. See followg pages or consult factory for specific recommendations. 2 Nomal capacities based on handlg th liquids at RPM on three small sizes, RPM on three large sizes. Solvents, alcohols, aqueous solutions and similar liquids. Metric conversions are based on US measurements and rounded to the nearest whole number. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 06
22 Section 64 Page 64.2 Issue D VIKING HEAVY DUTY PUMPS SERIES 497 STAINLESS STEEL SERIES 497 s GG, HJ and HL Sizes Vikg s Series 497 heavy-duty pumps are furnished with an tegral relief valve as shown the pump photos above. Note: On the GG, HJ and HL sizes, the valve mounts on the pump head. The AS, AK and AL size valve mounts on top of the pump casg. All sizes equipped with PTFE mechanical seal with carbon rotatg and staless alloy stationary faces. An optional Viton or Kalrez / carbon versus silicon carbide MECHANICAL SEAL Staless steel retaer. 2 Staless steel sprg. PTFE shaft wedge. 4 Carbon rotatg face (washer). 5 Stationary seat. 6 PTFE seat rg. 7 Anti-rotation p. SERIES 497 s AS, AK and AL Sizes mechanical seal which is well suited for th liquid applications is available on request.dimensions for Unmounted s See Page Performance Data for Unmounted s See Pages 64.9 through CONSTRUCTION SERIES 497 ( GG THROUGH AL SIZES) Construction Casg Head Rotor Idler Rotor Shaft Idler P Idler Bushg Shaft Sealg Mechanical Seal 5 Internal Safety Relief Valve 6 Staless Staless Staless Staless 770 Staless Alloy Staless Staless with Corrosionresistant coatg Carbon Graphite Staless, PTFE, Carbon Graphite And Staless Alloy Staless SPECIFICATIONS Model Numbers 50 lb. ANSI Flanged Port Size Nomal Ratg Hydrostatic 2 Discharge Temperature VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 06 Approximate Shippg Weight With Valve Unmounted Inches GPM (m³/hr) RPM PSIG (BAR) PSIG (BAR) Degrees Pounds (KG) GG497 HJ497 HL () (2) () (7) AS (8) AK () AL (7) Nomal capacities based on handlg th liquids at RPM on three smaller sizes, RPM on three larger sizes. 2 If suction pressure exceeds 00 PSIG (7 BAR), consult factory. Standard PTFE seal from 0 F. to +50 F. Special construction required Metric conversions are based on US measurements and rounded to the nearest whole number (5) below 8 SSU 00 (7) 8 to 00 SSU 50 (0) 00 to 750 SSU 0 (4) above 750 SSU 4 75 (5) below 8 SSU 00 (7) 8 to 00 SSU 50 (0) 00 to 750 SSU 0 (4) above 750 SSU 4 75 (5) below 8 SSU 00 (7) 8 to 00 SSU 50 (0) 00 to 750 SSU 0 (4) above 750 SSU 4 75 (5) below 8 SSU 00 (7) 8 to 00 SSU 50 (0) 00 to 750 SSU 0 (4) above 750 SSU 4 75 (5) below 8 SSU 00 (7) 8 to 00 SSU 50 (0) 00 to 750 SSU 0 (4) above 750 SSU 4 75 (5) below 8 SSU 00 (7) 8 to 00 SSU 50 (0) 00 to 750 SSU 0 (4) above 750 SSU above +. 4 Solvents, alcohols, aqueous solutions and similar liquids. 5 All valves set at 00 lbs. unless otherwise ordered. 6 Models AS and AK have 2½ cored opengs. (9) 50 (2) 50 (2) 5 (52) 5 (52) (55)
23 SERIES 497 STAINLESS STEEL Section 64 Page 64. Issue D DIRECT DRIVE UNITS ( D DRIVE) SERIES 497 s with D Drive GG, HJ and HL Sizes SERIES 497 s with D Drive AS, AK and AL Sizes Vikg s Series 497D units the GG, HJ and HL size (nomal ratg 0,, 0 GPM) are designed for high-speed, heavy-duty service. The pump is connected by a flexible couplg with guard directly to a or RPM motor. Both pump and motor mount on a sturdy formed steel base. Vikg s three large size Series 497D direct-connected units all feature the Series 497 high-speed pump connected by a flexible couplg with guard to RPM motor. Both pump and motor are mounted on a formed steel base. These make very compact, rugged units for heavy-duty service, handlg many types of liquids up to 25,000 SSU (5,500 cst). Dimensions for D Drive See Page Performance Data for D Drive See Pages 64.9 through SPECIFICATIONS D DRIVE UNITS Model Numbers 50 lb. ANSI Flanged Port Size Nomal Ratg Nomal capacities based on handlg th liquids at RPM on three smaller sizes, RPM on three larger sizes. 2 If suction pressure exceeds 00 PSIG (7 BAR), consult factory. Metric conversions are based on US measurements and rounded to the nearest whole number. Hydrostatic 2 Discharge Standard PTFE seal from 0 F. to +50 F. Special construction required above +. 4 Solvents, alcohols, aqueous solutions and similar liquids. 5 Models AS and AK have 2½ cored opengs. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 06 Temperature Approximate Shippg Weight With Valve (Less Power) Mounted Unit Inches GPM (m³/hr) RPM PSIG (BAR) PSIG (BAR) Degrees Pounds (KG) GG497D HJ497D HL497D () (2) () (7) AS497D 5 5 (8) AK497D 5 50 () AL497D 75 (7) 4 75 below 8 SSU 00 8 to 00 SSU to 750 SSU 0 above 750 SSU 4 75 below 8 SSU 00 8 to 00 SSU to 750 SSU 0 above 750 SSU 4 75 below 8 SSU 00 8 to 00 SSU to 750 SSU 0 above 750 SSU 4 75 below 8 SSU 00 8 to 00 SSU to 750 SSU 0 above 750 SSU 4 75 below 8 SSU 00 8 to 00 SSU to 750 SSU 0 above 750 SSU 4 75 below 8 SSU 00 8 to 00 SSU to 750 SSU 0 above 750 SSU 50 (2) 80 (6) 80 (6) 250 (4) 250 (4) 270 (2)
24 Section 64 Page 64.4 Issue C VIKING HEAVY DUTY PUMPS SERIES 497 STAINLESS STEEL DIMENSIONS These dimensions are average and not for construction purposes. Certified prts on request. For specifications, see page SERIES 497 GG HJ HL SIZES MODEL NO. A B D E F G H J K L M N O P S T U V W X GG497 HJ497 HL x mm x x mm x x mm x For specifications, see page SERIES 497 AS AK AL SIZES Models AS and AK have 2½ cored MODEL NO. AS497 AK497 AL497 A B D E F G H J K L M N O P S T U V W X Z x mm x x mm x x mm x VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 06
25 SERIES 497 STAINLESS STEEL DIMENSIONS These dimensions are average and not for construction purposes. Certified prts on request. Section 64 Page 64.5 Issue C For specifications, see page 64.. SERIES 497 ( D DRIVE) GG HJ HL AS AK AL SIZES MODEL NO. A B D E F H J K L M M N P S GG497D mm mm frame motors (short base). (Available with GG size pump.) 2 4T and 45T frame motors (long base). (Available with GG size pump.) 56, 4T and 45T frame motors. (Available with HJ or HL size pumps.) 4 82, 82T, 84, 84T frame motors. (Available with HJ through AL size pumps.) 5 2, 2T, 25, 25T frame motors. (Available with HJ through AL size pumps.) 6 254U, 254T, 256U, 256T frame motors. (Available with AK through AL size pumps.) 7 Dimension cludes motor block, base height is. 8 Dimension cludes motor block, base height is 2. 9 Models AS and AK have 2½ cored opengs. NOTE: All AS, AK, AL pump sizes available with any of the three motors shown. HJ497D HL497D AS497D AK497D AL497D mm mm mm mm mm mm VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 06
VIKING HEAVY DUTY PUMPS SERIES 4193 AND 493 STEEL EXTERNALS FEATURES
VIKING HEAVY DUTY PUMPS SERIES 49 AND 49 FEATURES Section 54 Page 54. Issue C Pressure Range 2 Temperature Range Viscosity Range 250 PSI ( BAR) for 00 SSU ( cst) and above 50 PSI (0 BAR) for 8 to 00 SSU
More informationVIKING HEAVY DUTY PUMPS SERIES 4197 STAINLESS STEEL FEATURES
VIKING HEAVY DUTY PUMPS FEATURES Section 64 Page 64. s Cutaway View 0--0 GPM Sizes (2-4.5-7 m³/hr) s Cutaway View 5-50-75 GPM Sizes (8--7 m³/hr) Pressure Range Temperature Range Viscosity Range 0 PSI (4
More informationVISCOSITY RANGE GPM m 3 h PSI Bar F C SSU cst
SERIES 493, 493 Section 34 Page 34. TBLE OF CONTENTS Features & Benefits...2 Specifications...2 Standard Materials of Construction...2 Key...3 Cutaway View & Pump Features...3 Mountg Options...4 Dimensions
More informationVIKING MOTOR SPEED INTERNAL GEAR PUMPS
VIKING MOTOR SPEED Series Description Vikg s Motor Speed series ternal gear pumps represent a technological advance the science of flow. Through new techniques of feedg the rotor and idler, Vikg has achieved
More informationVIKING GENERAL PURPOSE PUMPS SERIES 32 AND 432
Page 310.1 FEATURES SERIES 32 and 432 3 GPM (.7 m³/hr) Size Shown. or Mechanical seal type. Valve on casing. SERIES 432 5 GPM (1 m³/hr) Mechanical seal type. Shown with valve on head. C, F & FH Sizes J
More informationPRODUCT OBSOLETED 1Q16
STANDARD CONSTRUCTION FEATURES Page 141.1 SERIES 15 Pumps Cutaway View (Packed Type) 8-15-0 GPM Sizes (--7 m³/hr) MECHANICAL SEAL (SERIES 415) G - HL, K - LL SIZES AK, AL, LS - M SIZES BRACKET 5 416 SHAFT
More informationVIKING SPUR GEAR SINGLE PUMPS SERIES SG-04, SG-05, SG-07 AND SGN-05, SGN-07 STANDARD CONSTRUCTION FEATURES
VIKING SPUR GEAR SINGLE PUMPS FEATURES Section 34 Page 34. SERIES SG-04 and SG-05 Pumps Cutaway View.0 to.2 GPM Sizes (.0 to 2.5 m³/hr) SERIES SG-07 Pump Cutaway View 2.8 to 32.0 GPM Sizes (. to 7 m³/hr)
More informationVIKING HEAVY DUTY PUMPS SERIES 225 AND 4225 JACKETED BRACKET, STANDARD CONSTRUCTION FEATURES
VIKING HEAVY DUTY PUMPS JACKETED BRACKET, STARD CONSTRUCTION FEATURES SERIES 5 Pumps Cutaway View 5-0-60-80-5 GPM Sizes (-7--8- m³/hr) Section Page. Issue C MECHANICAL SEAL (SERIES 5) H - LL SIZES LS -
More informationVIKING SG SERIES SEALLESS MAG DRIVE PUMPS
SERIES SG-04, -05, -07, -0, -4 (Cast Iron) Section 34.3 Page 34.3. OPERATING RANGE: SG Pumps (Cast Iron Mag Drive) and SGN (Ductile Iron Mag Drive) Displacements No. 23 SG and 7 SGN 0.06 to 90 (SG) and
More informationMOTOR SPEED PRODUCT LINE: CAST IRON PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE. Section 1442 Page 1442.
Page 1442.1 TABLE OF CONTENTS Features & Benefits...2 Standard Materials of Construction...2 Specifications...2 Model Number Key...3 Cutaway View & Pump Features...3 Dimensions C, F, FH Sizes...4 Dimensions
More informationSPUR GEAR PRODUCT LINE: CAST IRON PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE. Section 1451 Page 1451.
Page 1451.1 TABLE OF CONTENTS Features & Benefits...2 Typical Applications...2 Port Location Options...2 Model Number Key...3 Standard Materials of Construction...3 Cutaway View & Pump Features...4 Component
More informationVIKING SG SERIES SINGLE PUMPS (WITH SHAFT SEAL)
SERIES SG-04, -05, -07, -10, -14 () Page 341.1.1 OPERATING RANGE: SERIES SG-04/-05 PUMP SG Pumps (, Lip or Mechanical Sealed) Displacements No. 29 Flow Range Pressure Range Temperature Range Viscosity
More informationUNIVERSAL PRODUCT LINE: STEEL EXTERNALS JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE
SERIES 4223, 4323 (API 682 Seal) Section 304 Page 304. TABLE OF CONTENTS Features & Benefits...2 Revolvable Pump Casings...2 Materials of Construction...2 Cutaway View & Pump Features...3 Key...4 Specifications...4
More informationPRODUCT OBSOLETED 1Q16
VIKING HEAVY DUTY PUMPS FEATURES Section 6 Page 6. Issue C 9 SERIES 27 s Cutaway View (Packed Type) 60-200-280 GPM Sizes (36-45-64 m³/hr) Shown without over-pressure relief valve MECHANICAL SEAL (SERIES
More informationVIKING HEAVY DUTY ALLOY PUMPS SERIES 724 AND 4724
VIKING HEAVY DUTY ALLOY PUMPS Section 210 Page 210.1 FEATURES SERIES 4724 Cutaway View Mechanical, 1½, 3 and 5 GPM Sizes 1 Range 200 PSI (14 BAR) for (21 cst) and above (Small Pumps F, FH and G sizes)
More informationDuctile Iron, Jacketed Pumps: Catalog Section 1602 Cast Iron, Non-Jacketed Pumps: Catalog Section 1401 HL4126A
Page 1601.1 TABLE OF CONTENTS Features & Benefits...2 Port Location Options...2 Model Number Key...3 Standard Materials of Construction...3 Cutaway View & Pump Features...4 Special Materials & Options
More informationLIQUID-SPECIFIC PRODUCT LINE: STAINLESS STEEL VANE PUMPS PRODUCT DESCRIPTION SERIES OPERATING RANGE 1 NOMINAL FLOW RATES 2
Page 445.1 PRODUCT DESCRIPTION SERIES OPERATING RANGE 1 Rotary vane pumps are used for liquid transfer in applications ranging from chemicals to LP gas. Vanes extend from slots on the rotor, sweeping liquid
More informationVIKING. Series LVP STAINLESS STEEL VANE PUMP. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA 2016 PRODUCT DESCRIPTION SERIES OPERATING RANGE
Page 445.1 PRODUCT DESCRIPTION Rotary vane pumps are used for liquid transfer in applications ranging from chemicals to LP gas. Vanes extend from slots on the rotor, sweeping liquid through a cam-shaped
More informationUNIVERSAL PRODUCT LINE: STEEL EXTERNALS JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE
SERIES 223A, 4223A, 323A, 4323A Page 1302.1 Issue B TABLE OF CONTENTS Features & Benefits...2 Jacketing...2 Relief Valve Configurations...3 Porting & Sealing...3 Revolvable Pump Casings...3 Cutaway View
More informationUNIVERSAL PRODUCT LINE: STAINLESS STEEL NON-JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE:
Page 1701.1 TABLE OF CONTENTS Features & Benefits...2 Port Location Options...2 Model Number Key...3 Standard Materials of Construction...3 Cutaway View & Pump Features...4 Special Materials & Options
More informationVIKING. Series LVP. VIKING PUMP A Unit of IDEX Corporation Cedar Falls, IA Section 445 Page Issue C
VIKING Section 445 Page 445.1 Issue C PRODUCT DESCRIPTION Rotary vane pumps are used for liquid transfer in applications ranging from chemicals to LP gas. Vanes extend from slots on the rotor, sweeping
More informationNominal Flow. Pressure Range. Temp. Range. Viscosity Range. Nominal Flow. Pressure Range. Temp. Range. Viscosity Range. Stainless Steel.
Page 630.1 Heavy-Duty, Foot-Mounted Internal Gear Pumps With Multiple Seal Options Standard Pump (shown: KK124A) Operating Range 1 : Cast Iron Series: 124A/AE, 4124A/AE, 324A, 4324A, 224A/AE, 4224A/AE
More informationUNIVERSAL PRODUCT LINE: DUCTILE IRON JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE
Page 1602.1 TABLE OF CONTENTS Features & Benefits...2 Porting & Sealing...2 Jacketing...2 Revolvable Pump Casings...2 Cutaway View & Pump Features...3 Model Number Key...4 Standard Materials of Construction...4
More informationUNIVERSAL PRODUCT LINE: CAST IRON NON-JACKETED PUMPS SERIES DESCRIPTION TABLE OF CONTENTS RELATED PRODUCTS OPERATING RANGE:
Page 1401.1 TABLE OF CONTENTS Features & Benefits...2 Port Location Options...2 Model Number Key...3 Standard Materials of Construction...3 Cutaway View & Pump Features (124A/AE, 4124A/AE, 324A, 4324A)...4
More informationVIKING JACKETED ASPHALT PUMPS
VIKING ED ASPHALT PUMPS SERIES 34 AND 434 Section 430 Page 430.1 Issue G FEATURES 1 Pressure 1 Temperature 1 Viscosity 1 Flow To 100 PSI (6.9 Bar) -60 F. to +450 F. (-51 C. to +232 C.) 31 SSU to 250,000
More informationUNIVERSAL PRODUCT LINE: STAINLESS STEEL JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE
UNIVERSAL PRODUCT LINE: SERIES 227A, 4227A, 327A, 4327A Section 1702 Page 1702.1 Issue B TABLE OF CONTENTS Features & Benefits...2 Jacketing...2 Relief Valve Configurations...3 Porting & Sealing...3 Revolvable
More informationVISCOSITY RANGE GPM m 3 h PSI Bar F C SSU cst
UNIVERSL PRODUCT LINE: SERIES 724, 4724 Section 1706 Page 1706.1 Issue B TBLE OF CONTENTS Features & Benefits...2 Cutaway View & Pump Features...2 Model Number Key...3 Standard Materials of Construction...3
More informationVIKING UNIVERSAL SEAL PUMPS. Heavy-Duty, Foot-Mounted Internal Gear Pumps With Multiple Seal Options. Operating Range1: Nominal Flow Rates:
VIKING UNIVERSAL SEAL PUMPS Section 630 Page 630.1 Heavy-Duty, Foot-Mounted Internal Gear Pumps With Multiple Seal Options Operating Range1: Cast Iron Series 124A/AE, 4124A/AE, 4124B, 324A, 4324A, 224A/AE,
More informationProduct Range IDEX CORPORATION
Product Range IDEX CORPORATION Viking Pump provides an unmatched combination of application expertise and positive displacement pumping products to meet your pumping needs. We specialize in the design,
More informationVIKING UNIVERSAL SEAL PUMPS. Heavy-Duty, Foot-Mounted Internal Gear Pumps With Multiple Seal Options. Operating Range: Nominal Flow Rates:
VIKING UNIVERSAL SEAL PUMPS Section 630 Page 630. Heavy-Duty, Foot-Mounted Internal Gear Pumps With Multiple Options Standard Pump (shown: KK123A) Jacketed Pump (shown: KK4223A) Nominal Flow Rates: Pump
More informationMOTOR SPEED PRODUCT LINE: CAST IRON MAG DRIVE PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE
MOTOR SPEED PRODUCT LINE: SERIES 895 Section 1443 Page 1443.1 Issue B TBLE OF CONTENTS Features & Benefits...2 Standard Materials of Construction...2 Key...3 Cutaway View & Pump Features...3 Specifications...4
More informationMOTOR SPEED PRODUCT LINE: CAST IRON PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE. Section 1441 Page 1441.
MOTOR SPD PRODCT LIN: SRIS 495, 495 Section 44 Page 44. Issue TL OF CONTNTS Features & enefits...2 Standard Materials of Construction...2 Cutaway View & Pump Features...3 Key...4 Specifications...4 Mounting
More informationLACT PERFORMANCE PRODUCTS
LACT PRODUCTS DURABLE & RELIABLE SOLUTIONS BOLTS PLUG LID Low Pressure Drop Inclined basket design for low pressure drop and high system efficiency O-RING Easy to Clean Top basket removal eliminates the
More informationVIKING. Viking Mag Drive Series 855. Ideal for: Hard-to-Seal Liquids 24/7 Operations Hazardous and Toxic Liquids
Viking Mag Drive Series 855 VIKING Ideal for: Hard-to-Seal Liquids 24/7 Operations Hazardous and Toxic Liquids Capacity to 29.5 M 3 /Hr (130 GPM) Pressure to 14 Bar (200 PSI) Viscosity to 55,000 cst (250,000
More informationCatalog PR-99. Tri-Clover. PR Series Positive Rotary Pump
Catalog PR-99 Tri-Clover PR Series Positive Rotary Pump PR - The Pump that was designed with the Processor md The Tri-Clover PR le was designed to overcome many of the traditionally troublesome operatg
More informationViking SL Industrial Lobe Pump Series
Section 288 Page 288. Viking SL Industrial Lobe Pump Series This product brings gentle low shear pumping action with in-line cleaning capabilities to the industrial markets. Rugged enough for corrosive
More informationPIPELINE INJECTION PRODUCTS
PIPELINE INJECTION PRODUCTS DURABLE & RELIABLE SOLUTIONS PIPELINE INJECTION PUMP GP-10 & GP-1 SERIES Flows up to: 210 GPM / BPH / 7,20 BPD (nominal flow) BUSHINGS BACK PULL OUT SEAL HEAD DRIVER SHAFT DRIVEN
More informationTOUGH SIMPLE GEAR PUMPS COST EFFECTIVE TOUGH SIMPLE COST EFFECTIVE. Tel: / Int'l: Fax: / Int'l:
GEAR PUMPS TOUGH TOUGH SIMPLE SIMPLE COST EFFECTIVE COST EFFECTIVE NOMAD GEAR PUMPS California-based JDA GLOBAL LLC, the world s largest provider of after-market diaphragm pump products, in conjunction
More informationTECHNICAL SERVICE MANUAL
TECHNICAL SERVICE MANUAL HEAVY-DUTY bracket mounted PUMPS SERIES 4193 AND 493 SIZES GG - AL SECTION TSM 154 PAGE 1 of 10 ISSUE C CONTENTS Introduction....................... 1 Special Information...................
More informationGEAR PUMPS TOUGH TOUGH SIMPLE SIMPLE COST EFFECTIVE COST EFFECTIVE
GEAR PUMPS TOUGH TOUGH SIMPLE SIMPLE COST EFFECTIVE COST EFFECTIVE NOMAD GEAR PUMPS California-based JDA GLOBAL LLC, the world s largest provider of after-market diaphragm pump products, in conjunction
More informationNominal Flow Pressure Range Temp. Range Viscosity Range
VIKING UNIVERSL XPD 676 PUMPS - FULL COMPLINCE with PI 676 STNDRDS SERIES 4223X & 4323X Section 633 Page 633.1 Heavy-Duty, Foot-Mounted Internal Gear Pumps Offering Full Compliance with PI 676 Design Standards
More informationVane Pumps for Corrosive, Thin Liquids at Higher Pressures
Viking LVP Series Stainless Steel Vane Pumps Vane Pumps for Corrosive, Thin Liquids at Higher Pressures Higher pressures than other stainless positive displacement pumps Low-wear, long-life vanes Superior
More informationVane Pumps for Corrosive, Thin Liquids at Higher Pressures
Viking LVP Series Stainless Steel Vane Pumps Vane Pumps for Corrosive, Thin Liquids at Higher Pressures Capacity to 36 M³/Hr (160 GPM) Pressure to 14 Bar (200 PSI) Viscosity 0.1 to 500 cst (28 to 2,300
More informationHigh Temperature Air-Cooled Hot Oil Pumps
Bulletin C 1.4.42 Dean Pump Division High Temperature Air-Cooled Hot Oil Pumps No Water Cooling Required RA3 RA2 DEAN PUMP SERIES RA FAN COOLED HIGH TEMPERATURE HOT OIL PUMPS No Liquid Cooling Required
More informationModel Z4500 Stationary Pump
LPGCVP3C Sales Catalog for Stationary and Truck Pumps Model Z32 Truck Pump Model Z35 Stationary and Truck Pump Model Z45 Stationary Pump Model C51 Direct-Coupled Mounting Model 121 Stationary Coro-Vane
More informationHelical Hydraulic Rotary Actuators. we carry the load.
Helical Hydraulic Rotary Actuators we carry the load. POWERFUL High torque High bearg capacity DURABLE Movg parts enclosed Suitable for harsh environments Helac s novative Powered Hge Helical, Hydraulic
More informationGEAR PUMPS TOUGH INTERNAL GEAR SIMPLE SIMPLE EXTERNAL GEAR COST EFFECTIVE COST EFFECTIVE
TOUGH INTERNAL GEAR GEAR PUMPS SIMPLE SIMPLE EXTERNAL GEAR COST EFFECTIVE COST EFFECTIVE NOMAD GEAR PUMPS California-based JDA GLOBAL LLC, the world s largest provider of after-market diaphragm pump products,
More informationITT. Goulds Pumps G&L Series NPO. Engineered for life. Commercial Water. Open Impeller All Stainless Steel End Suction Pumps.
ITT Goulds Pumps G&L Series NPO Open Impeller All Stainless Steel End Suction Pumps www.goulds.com Engineered for life A Full Range of Product Features NPO Product Line Numbering System Superior Materials
More informationCLARK SOLUTIONS S Series Rotary Gear Pump Pressure to 200 PSI, Flow to 32 GPM, Drive Speed to 1800 RPM
CLARK SOLUTIONS S Series Rotary Gear Pump Pressure to 200 PSI, Flow to 32 GPM, Drive Speed to 1800 RPM DESCRIPTION Series S pumps are general purpose positive displacement gear pumps and are a good choice
More informationCoro-Flo Sales Catalog
LPGCFP100C LPG Pumps Coro-Flo Sales Catalog FF-Model DL-Model DLF-Model C-Model Table of Contents General Information What is a Coro-Flo Pump...3 History of the Coro-Flo Pump... 4 Markets Served... 4 Model
More informationSealless Mag Drive Pumps For Crucial Liquid Containment Applications
Viking Mag Drive Pumps Sealless Mag Drive Pumps For Crucial Liquid Containment Applications Eliminates pump seal maintenance Highest level of liquid containment available Metric or U.S. Design Sizes in
More informationIndustrial Pump Catalog
Industrial Pump Catalog Contents Why Corken?........................................................................ i-5 About This Catalog...................................................................
More informationTECHNICAL SERVICE MANUAL
Electronic copies of the most current TSM issue can be found on the Viking Pump website at www.vikingpump.com TECHNICAL SERVICE MANUAL HEAVY-DUTY Stainless steel PUMPS SERIES 4197 SIZES GG, hj, hl, as,
More informationBasic Hydraulic Features. Basic Mechanical Features
APRIL 2006 1.0 Overview The ETA is designed for flow rates that fall beyond the range of most end suction pumps. Performance extends to 9,500 GPM, 440 feet of head, and 88% efficiency. This range is covered
More informationTemperature regulating valve Type ORV
Data sheet Temperature regulatg valve Type ORV ORV are 3-way dustrial valves for matag a constant oil temperature gas compressor systems, by mixg hot and cold oil the lubricatg system of e.g. screw or
More informationPOMPE À ENGRENAGES GEAR PUMP ASYBCO
POMPE À ENGRENAGES GEAR PUMP ASYBCO GEAR PUMP Series 5 Canadian General Purpose Designed and engineered to serve petroleum, chemical, process and manufacturing industries. GPM (289 L/m) PSI (690 kpa) /2
More informationITT. Goulds Pumps. G&L Series SSH S & M-Group 316 Stainless Steel End Suction Pumps. Engineered for life. Commercial Water.
ITT Goulds Pumps G&L Series SSH S & M-Group 316 Stainless Steel End Suction Pumps www.goulds.com Engineered for life A Full Range of Product Features Superior Materials of Construction: AISI Type 316L
More informationRS Multi-Stage, Ring Section Pumps
RS Multi-Stage, Ring Section Pumps Technical Specification Pages This page left intentionally blank. 1.0 Overview. The RS Series is Carver s multi-stage pump for fluids at moderate to high pressures. The
More informationVIKING. Metric Motor Speed Pumps
Metric Motor Speed Pumps VIKING Serving Applications For: Chemical Processors Grain Processors Rotating Equipment OEMs Petroleum Products And Many Others Flows: to 45 M 3 /Hr Pressures: to 17 BAR Viscosities:
More informationVIKING HG SERIES HELICAL GEAR EXTERNAL GEAR PUMPS
Page 350.1 Series Description Viking s HG series positive displacement pumps are designed to provide low noise transfer and processing of clean, lubricating liquids for applications such as lube oils,
More informationTECHNICAL BROCHURE B36/ /3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS
TECHNICAL BROCHURE B36/3742 3642/3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS FEATURES Compact Design: Close coupled, space saving design provides easy installation. Flexible couplings and bedplates
More informationBSM ROTARY GEAR PUMPS
FT. MTD. PUMP B-Series pumps are a good choice for a variety of recirculating, mixing, and transfer applications. Typical pumped liquids include solvents, resins, and petroleum products. These pumps are
More informationSaf-T-Gard Hydraulic Actuator MH 60 Series
Description Saf-T-Gard Hydraulic Actuator MH 60 Series for use with ", 4, 5 and 6" nomal gate valves The The Cameron MH Hydraulic Actuator product le has been developed by usg the superior features of
More informationTECHNICAL BROCHURE B36/3742 R2 3642/3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS
TECHNICAL BROCHURE B36/3742 R2 3642/3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS FEATURES Compact Design: Close coupled, space saving design provides easy installation. Flexible couplings and
More informationHelical Hydraulic Rotary Actuators
Helical Hydraulic Rotary Actuators we carry the load. POWERFUL High torque High bearg capacity DURABLE Movg parts enclosed Suitable for harsh environments Helac s novative Powered Hge Helical, Hydraulic
More informationL Q LIQUID-SPECIFIC PRODUCT LINE: CAST IRON ASPHALT PUMPS SERIES DESCRIPTION (34 & 32E) OPERATING RANGE: MODEL NUMBER KEY:
LIQUID-SPECIFIC PRODUCT LINE: SERIES 4A, 4AE, 44A, 44AE, 34A, 434A, 14E, 34E, 34, 3E Section 430 Page 430.1 Issue S SERIES DESCRIPTION (34 & 3E) Viking 34 Series Asphalt Pumps are designed to handle asphalts,
More informationGENERAL PUMPS FIRE PUMPS ESPAÑA APPROVED EX
FIRE PUMPS FM EX2 APPROVED www.pumpsgp.com General Pumps SL., was established more than 2 years ago Valencia, Spa. We are a major manufacturer Spa of a wide variety of water pumps for various applications.
More informationPARALLEL PNEUMATIC HEAVY DUTY GRIPPER
PARALLEL PNEUMATIC HEAVY DUTY GRIPPER Major Benefits Compact, low profile design provides high grip force and large moment capacities with low overall weight. Ultra-rigid, wear-compensatg jaw guide system
More informationEN. 850 Filtrate Pumps. Technical Specification Pages
850 17.01.EN 850 Filtrate Pumps Technical Specification Pages 850 Series Filtrate Pump 850 17.01.EN This page left intentionally blank. 1.0 Overview. The 850 is Carver s filtrate pump line designed for
More information390 Series Multi-Stage Vertical In-Line Centrifugal Pumps
Bulletin 390 /Rev. B 390 Series Multi-Stage Vertical In-Line Centrifugal Pumps Capacities to 400 G.P.M. (91 M 3 /HR) Heads to 800 Feet (243 Meters) Temperatures to 250 F (120 C) motralec 4 rue Lavoisier.
More informationHigh Temperature Chemical Process Inline Pumps
Bulletin C-1.2.21. Dean Pump Division High Temperature Chemical Process Inline Pumps Series DL Series DL High Temperature Chemical Process Inline Pumps Capacities to 6 GPM (182 m 3 /hr) Heads to feet (167
More informationT 8075 EN Type 3591 Globe Valve ANSI version
T 8075 EN Type 3591 Globe Valve ANSI version Application Matenance-friendly cage valve for process engeerg applications with high dustrial requirements Valve size NPS 10 to 32 Pressure ratg to 900 Temperatures
More informationV Rev US
V - 0805 Rev. 05 - US APPLICATIONS INDUSTRIES V series internal gear rotary pumps are suitable for pumping liquids of any viscosity. Solids cannot be handled, but the pumps can cope with abrasive particles.
More informationStafford, Texas USA. 55,000 square feet ISO 9001:2008 API 6D CE/PED ISO/TS API Q1
F L O A T I N G B A L L V A L V E S JAG flocomponents USA, Inc Stafford, Texas USA 55,000 square feet ISO 9001:008 API 6D CE/PED ISO/TS 9001 API Q1 JAGf lo s wholly owned Dalian, Cha facility uses state
More informationHigh Temperature Air-Cooled Hot Oil Pumps
Bulletin C 1.4.42 Dean Pump Division High Temperature Air-Cooled Hot Oil Pumps No Water Cooling Required RA296 RA3146 RA3186 RA296 The smaller, foot mounted economy version of the air-cooled RA series
More informationDiaphragm Accumulators
SBO Diaphragm Accumulators Description Diaphragm accumulators are a cost effective option for numerous functions volvg energy storage, shock absorption or pulsation dampeng a hydraulic or fluid system.
More information8L SERIES THREE SCREW PUMPS
TM 8L SERIES THREE SCREW PUMPS The reliable pump people ROTARY SCREW PUMPS Performance Shown at 1500 PSID (103 BAR), 200 SSU (43 CST) 60 HZ: 870 1150 1750 50 HZ: 960 1450 1200 1100 630M 40 250 1000 900
More informationGENERAL OVERVIEW BRONZE PEDESTAL ROTARY GEAR N13HDM C992 BRONZE BRONZE HELICAL ROTOR 101BG RUBBER
GENERAL OVERVIEW BRONZE CLOSE COUPLED N970 BRONZE PEDESTAL N4000R BRONZE PEDESTAL ROTARY GEAR N13HDM PLASTIC CENTRIFUGAL 144 RUBBER ROLLER 310F BRONZE CENTRIFUGAL 50P DUCTILE IRON CLOSE COUPLED C992 BRONZE
More informationTECHNICAL SERVICE MANUAL
Electronic copies of the most current TSM issue can be found on the Viking Pump website at www.vikingpump.com TECHNICAL SERVICE MANUAL HEAVY-DUTY Stainless steel BRACKET MOUNTED PUMPS SERIES 127 AND 4127
More informationRegenerative Turbine Pumps
Bulletin E4 November 009 E4 T4 Series Regenerative Turbine Pumps Capacities to GPM Heads to 600 Feet Temperatures to 00 F MTH PUMPS MTH E4 T4 Series Close-coupled and pedestal mounted regenerative turbine
More informationEFQT/EFQU. EBARA Self Priming Trash Pump. Contents Project: Model: Chk d: Date:
Contents Section Page Model Designation 2 Features 3 Standard Specifications 5 Specifications 6 Selection Chart 7 Suction Speed Flow Chart 9 Performance Curves 10 Dimension Drawings 20 Model Designation
More information1SV (e-sv) 60 Hz 3500 RPM
DIMENSIONS AND ENGINEERING PAGE 31 CONSTRUCTION: 34 STAINLESS STEEL NOMINAL FLOW: 9 GPM CAPACITIES: 2-12 GALLONS PER MINUTE HEADS: 13 372 PSI TDH STAGING: 2 3 MINIMUM FLOW: 2 GPM MAXIMUM WORKING 36 PSI
More informationTECHNICAL SERVICE MANUAL
TECHNICAL SERVICE MANUAL ABRASIVE LIQUID HEAVY-DUTY BRACKET MOUNTED PUMPS SERIES 4625 SIZES H - M SECTION TSM 410.2 PAGE 1 of 10 ISSUE C CONTENTS Introduction....................... 1 Special Information...................
More informationBSM ROTARY GEAR PUMPS
-SERIES FLG. MTD. PUMP PUMP FOOT The BSM -Series pumps are designed to provide quiet and efficient service at standard motor speeds, moderately high pressures. Typical applications are supplying hydraulic
More informationPRODUCT OBSOLETED 4Q16
Electronic copies of the most current TSM issue can be found on the Viking Pump website at www.vikingpump.com TECHNICAL SERVICE MANUAL SECTION TSM 141.1 HEAVY-DUTY BRACKET MOUNTED PUMPS PAGE 1 of 16 SERIES
More informationPARALLEL PNEUMATIC 3-JAW GRIPPER
PARALLEL PNEUMATIC 3-JAW GRIPPER Major Benefits 3 jaw design provides self-centerg and maximum contact between part and jaw toolg Low profile to grip force and jaw travel ratios Eight sizes available both
More informationCASING COVER PLATE LUBRICATION GASKETS PRESSURE RELIFE VALVE SEAL OPTIONAL EQUIPMENT
Series: PFSPT Self-Priming Centifugal Pumps Size: x, Solids -1/ DISCHARGE x, lbs. Flange LIQUID TEMPERATURE 1 F CASING IMPELLER SHAFT SHAFT SLEEVE WEAR RING COVER PLATE FLAP VALVE Gray Iron ASTM A- Class
More informationA Series General Purpose Pumps General Purpose Pumps for Pressure Lubrication, Hydraulic Service, Fuel Supply and General Transfer
THE LEADING FORCE behind liquids since 1857 A Series General Purpose Pumps General Purpose Pumps for Pressure Lubrication, Hydraulic Service, Fuel Supply and General Transfer The Roper Pump Family of Gear
More information1SV (e-sv) 50 Hz 2900 RPM
DIMENSIONS AND ENGINEERING PAGE 37 CONSTRUCTION: 34 STAINLESS STEEL NOMINAL FLOW: 9 GPM CAPACITIES: 2-12 GALLONS PER MINUTE HEADS: 13 372 PSI TDH STAGING: 2 3 MINIMUM FLOW: 2 GPM MAXIMUM WORKING 36 PSI
More information3312 Model. pumping Model Model AURORA Series HORIZONTAL AND VERTICAL CLOSE-COUPLED PUMPS
3312 Model pumping 3314 Model 3311 Model AURORA 3310 Series HORIZONTAL AND VERTICAL CLOSE-COUPLED PUMPS WWW.AURORAPUMP.COM AURORA 3310 Series Horizontal and Vertical Close-Coupled Pumps Capacities to 3800
More information855 Filtrate Pump, Close Coupled and Overhead Mounted Pumps
855 Filtrate Pump, Close Coupled and Overhead Mounted Pumps Technical Specification Pages This page left intentionally blank. 1.0 Overview. The 855 Series is Carver s offering specifically designed to
More informationCONTENTS. VIKING PUMP, INC. A Unit of IDEX Corporation Cedar Falls, IA USA SECTION TSM 710.1
TECHNICAL SERVICE MANUAL industrial heavy duty motor speed pumps SERIES 4076 AND 4176 SIZES hle, ate and ale SECTION TSM 710.1 PAGE 1 of 8 ISSUE B CONTENTS Introduction....................... 1 Safety
More informationMotorized Pulley 500L, 500M & 500H, Ø in. (501 mm)
Motorized Pulley 500L, 500M & 500H, Ø 19.72. (501 mm) Our 19.72 diameter Motorized Pulley range offers three different performance levels for BULK applications: - L for Light duty - M for Medium duty -
More informationDisplacement 5.3L 325 CID. Stroke 92.0 mm in. Firing Order Spark Plug Gap 1.02 mm 0.04 in
Enge Mechanical Specifications (RPO LMG VIN 0) Specification Application Metric English General Enge Type V8 Displacement 5.3L 325 CID RPO LMG VIN 0 Bore 96.0-96.018 3.779-3.78 Stroke 92.0 3.622 Compression
More informationEclipse. The Power of Design Innovation. Series
Eclipse The Power of Design Innovation Series Pulsafeeder Technology Since 1936, Pulsafeeder has been recognized as a world leader in fluid handling and control technology. Pulsafeeder continues to deliver
More informationProduct Numbering System Typical Specifi cations, Models 4AC, 4AE, 6AC, 6AE, 8AC Pump Assembly, Types AC & AE
Index Sheet ITEM S Bulletin Product Numbering System... 1 Typical Specifi cations, Models 4AC, 4AE, 6AC, 6AE, 8AC... 2 Pump Assembly, Types AC & AE... 3-4 Dimensions, Types AC & AE... 5-8 Selection Curves,
More informationTECHNICAL SERVICE MANUAL
Electronic copies of the most current TSM issue can be found on the Viking Pump website at www.vikingpump.com TECHNICAL SERVICE MANUAL BEHIND THE ROTOR SEAL HEAVY DUTY PUMPS SERIES 4124B AND 4224B CAST
More informationTECHNICAL SERVICE MANUAL
Electronic copies of the most current TSM issue can be found on the Viking Pump website at www.vikingpump.com TECHNICAL SERVICE MANUAL industrial heavy duty motor speed pumps SERIES 4076 AND 4176 SIZES
More informationPRODUCT OBSOLETED 1Q16
TECHNICAL SERVICE MANUAL HEAVY DUTY STEEL EXTERNAL MOUNTED PUMPS SERIES 123 AND 4123 SIZES H-LL SECTION TSM 151.1 PAGE 1 OF 13 ISSUE C CONTENTS Introduction 1 Special Information 2 Maintenance 3 Packed
More information3800 Series. Single Stage End Suction Pumps. Capacities to 4200 G.P.M. (954 m 3 /hr) Heads to 520 Feet (180 Meters) Temperatures to 300 F (149 C)
3800 Series Single Stage End Suction Pumps Capacities to 200 G.P.M. (95 m 3 /hr) Heads to 520 Feet (180 Meters) Temperatures to 300 F (19 C) MODEL 380 Aurora 3800 Pump Setting New Standards of Efficiency
More information