Extrusion Pumps and Accessories

Transcription

1 Extrusion Pumps and Accessories

2 2 ARO Extrusion Pumps and Accessories

3 Numerical Index MODEL PAGE MODEL PAGE MODEL PAGE MODEL PAGE X X X4X B X4X X X X4X B X43-B X P4X X43-B XX P4X X XX4-B XX4-B XXX-B X4X XXX-B X47-B X X43-C X XX4-B X X44-B B B X B B XXX-B C XX NM2322E-11-P4X XXX NM2322F-11-P4X X4X XXX NP322L X4X XXX X 19 NP322L X4X NP322R X43-B X 19 NP322R X3-B B X 22 NP443R XX 23 P Table of Contents MODEL PAGE MODEL PAGE Extrusion Data: 4 Extrusion Accessories: Typical Application: 5 Steps To Order The Right Pump Model Reference Index: 6-7 Individual Pump Models Extrusion Packages: 8-13

4 4 Extrusion Pumps Extrusion pumps are frequently put in the most difficult of applications moving high viscosity fluids that are often abrasive. Extrusion pumps are used to apply a bead of material. In some instances the pump supplies a continuous bead; other applications call for intermittent delivery. Typical highviscosity fluids pumped include caulkings, heavy lubricants, mastics, sealers and inks. Application Parameters Viscosity can be the largest obstacle in an extrusion application. As viscosities increase, fluid flow decreases. In general, 2-ball pumps can be used for fluids with viscosities up to 50,000 cps. Chop-check pumps are used for higher viscosity fluids. Pump ratios used in extrusion applications range from 9:1 to 70:1. Additional equipment is needed to keep an extrusion pump primed. Follower plates, lifts and rams force the material into the pump inlet. Without this equipment, the fluid will not flow into the pump. Lifts can be used for fluids with viscosities up to 200,000 cps. Rams are needed for fluids with higher viscosities. If a fluid is stringy, a Ram may be needed for fluids with viscosities as low as 60,000 cps. Extrusion pumps also use fluid mass to keep the pump primed. When bulk tanks are used, the weight of the fluid will push it into the pump inlet. Accessories Required Extrusion Information Several accessories will improve the efficiency of an Extrusion application. They include: Follower Plates: Seal fluid container to maintain pump prime. Plates mount directly to pump inlet. Fluid is forced into pump. Available for 19 litre pails and 208 litre drums. Follower Seals: Forms seal between Follower Plate and Container to maintain prime. Available in Single or Double Lip Models. Use Single-Lip Wiper for viscosities up to 300,000 cp. Double Lip Wiper provides better wiping action on higher viscosity fluids. Use Double-Lip Wipers for fluid viscosities over 300,000 cp. Lifts: Eases changeover of empty containers. An internal cylinder lifts the pump from the container. Weight of air motor, pump and mounting bracket maintain pump prime. Used on medium to high viscosity fluids. Available for 208 litre drums. Rams: Function like a lift, but also exert downward force. An internal piston pushes the pump inlet into the fluid. Available in single or two-post configurations, for 19 or 208 litre containers. Used on medium to high viscosity fluids. Portability Kits: For single-post ram mounted pumps. Wheels bolt onto base of ram. Eases portability of unit around application site. Floor Mounts: Used when fluid is stored in large, bulk containers. Gravity feeds material into the pump inlet. Locate as close to fluid container as possible. Downstream Fluid Regulators: Used to control fluid pressure beyond the regulator. Downstream regulators cut fluid pressure to desired level. Also used to eliminate pulsation created by pump cycling. Extrusion Guns: Used to dispense fluids with viscosities above 200,000 cps. Available in manual or automatic configurations. Snuff-back guns eliminate drippage at work site. Extrusion Nozzle Kit: For manual or automatic extrusion guns. Size of orifice diameter controls size of bead extruded with the gun.

5 Typical Extrusion Applications: Typical Transfer Accessories: I.D. DESCRIPTION: See Page Number F-R-L Kit Assembly 24 ARO-STOP Over-run Control 25 Two Post Ram Downstream Fluid Regulator 21 Automatic Extrusion Gun 22 Extrusion Gun Nozzle Kit Single Post Ram 14 Z Swivel 23 Manual Extrusion Gun 23 Extrusion Nozzle Kit Extrusion Information

6 6 Ratio: Max. Flow Rate: Model Number: Pump Material: Pump Type 11: l/min X4X Stainless Steel 2-Ball 12: l/min X43-B Carbon Steel Chop Check 13: l/min XX4-B Carbon Steel Chop Check 20: l/min XX4-B Carbon Steel Chop Check 22:1 7.2 l/min X4X Stainless Steel 2-Ball 22:1 3.7 l/min NM2322E-11-P4X Carbon Steel Chop Check 22:1 3.7 l/min NM2322F-11-P4X Stainless Steel Chop Check 23: l/min X4X Stainless Steel 2-Ball 23:1 6.8 l/min X43-B Carbon Steel Chop Check 23: l/min X43-B Carbon Steel Chop Check 30: l/min XX4-B Carbon Steel Chop Check 30:1 4.9 l/min X4X Stainless Steel 2-Ball 40: l/min X4X Stainless Steel 2-Ball 43:1 3.4 l/min P4X Carbon Steel Chop Check 43:1 3.4 l/min P4X Stainless Steel Chop Check 44: l/min X47-B Carbon Steel Chop Check 45:1 7.2 l/min X4X Stainless Steel 2-Ball 46:1 6.4 l/min X43-B Carbon Steel Chop Check Extrusion Pump Model Reference Index 60:1 4.9 l/min X4X Stainless Steel 2-Ball 1.2:1 5.7 l/min XX4-B Carbon Steel Chop Check 3.6:1 5.7 l/min X43-C Carbon Steel Chop Check

7 Mount: Motor: Air Inlet: Fluid Outlet: Page #: 7 Stub /2 NPT(F) 1 NPT(F) or 208 litre /2 NPT(F) 1 NPT(F) or 208 litre 8 3/4 NPT(F) NPT(F) litre 10 3/4 NPT(F) NPT(F) 31 Stub /2 NPT(F) 1 NPT(F) litre 3 1/4 NPT(F) 1/2 NPT(F) litre 3 1/4 NPT(F) 1/2 NPT(F) 34 Stub 6 1/2 NPT(F) 1 NPT(F) or 208 litre /2 NPT(F) 1 NPT(F) or 208 litre 6 1/2 NPT(F) 1 NPT(F) litre 12 3/4 NPT(F) NPT(F) 38 Stub /2 NPT(F) 1 NPT(F) 39 Stub 8 3/4 NPT(F) 1 NPT(F) litre /2 NPT(F) 1/2 NPT(F) litre /2 NPT(F) 1/2 NPT(F) or 208 litre 8 3/4 NPT(F) 1 NPT(F) 43 Stub 6 1/2 NPT(F) 1 NPT(F) or 208 litre 6 1/2 NPT(F) 1 NPT(F) 45 Stub 6 1/2 NPT(F) 1 NPT(F) litre 4 in. 2 Hydraulic N/A NPT (F) litre 4 in. 2 Hydraulic N/A NPT (F) 48 To use with 60 kg drums see page 11. Extrusion Pump Model Reference Index

8 8 Package Contents NP322L :1 Ratio, Carbon Steel Extrusion Package NM2322E-11-P Carbon Steel Pump Air Filter/Regulator Carbon Steel Follower Plate Portable Lift Basic Pump Performance Air Inlet Pressure Range bar Fluid Pressure Range bar Maximum Working Flow: l/min Displacement Per Cycle cm 3 Lower Pump Material Carbon Steel Plunger Material Stainless Steel Air Motor Air Motor Repair Kit Lower Pump End Series P43 Lower Pump Repair Kit P43 NP322L0X-1 Portable Lift Only - Not a Ram Package Contents NP322L :1 Ratio, Stainless Steel Extrusion Package NM2322F-11-P Stainless Steel Pump Air Filter/Regulator Stainless Steel Follower Plate Portable Lift Extrusion Packages Basic Pump Performance Air Inlet Pressure Range bar Fluid Pressure Range bar Maximum Working Flow l/min Displacement Per Cycle cm 3 Lower Pump Material Stainless Steel Plunger Material Stainless Steel Air Motor Air Motor Repair Kit Lower Pump End Series P43 Lower Pump Repair Kit P43

9 Package Contents NP322R :1 Ratio, Carbon Steel Extrusion Package NM2322E-11-P Carbon Steel Pump F Air Filter R Air Regulator Carbon Steel Follower Plate B Single Post Ram Optional Portability Kit Optional Hold Down Kit 9 Basic Pump Performance Air Inlet Pressure Range bar Fluid Pressure Range bar Maximum Working Flow: l/min Displacement Per Cycle cm 3 Lower Pump Material Carbon Steel Plunger Material Stainless Steel Air Motor Air Motor Repair Kit Lower Pump End Series P43 Lower Pump Repair Kit P43 Package Contents NP322R0X-1 NP322R :1 Ratio, Stainless Steel Extrusion Package NM2322F-11-P Stainless Steel Pump F Air Filter R Air Regulator Stainless Steel Follower Plate B Single Post Ram Optional Portability Kit Basic Pump Performance Air Inlet Pressure Range bar Fluid Pressure Range bar Maximum Working Flow: l/min Displacement Per Cycle cm 3 Lower Pump Material Stainless Steel Plunger Material Stainless Steel Air Motor Air Motor Repair Kit Lower Pump End Series P43 Lower Pump Repair Kit P43 Extrusion Packages

10 10 Package Contents :1 Ratio, Carbon Steel Extrusion Package P Carbon Steel Pump Carbon Steel Follower Plate Portable Lift Basic Pump Performance Air Inlet Pressure Range bar Fluid Pressure Range bar 75 Cycles/Minute: l/min Displacement Per Cycle cm 3 Lower Pump Material Carbon Steel Plunger Material Stnls. Steel (Chrome Plated) Air Motor Air Motor Repair Kit Lower Pump End Series P43 Lower Pump Repair Kit P X-1 Air Powered Lift ONLY - Not a Ram Package Contents :1 Ratio, Stainless Steel Extrusion Package P Stainless Steel Pump Stainless Steel Follower Plate Portable Lift Extrusion Packages Basic Pump Performance Air Inlet Pressure Range bar Fluid Pressure Range bar 75 Cycles/Minute: l/min Displacement Per Cycle cm 3 Lower Pump Material Stainless Steel Plunger Material Stnls. Steel (Chrome Plated) Air Motor Air Motor Repair Kit Lower Pump End Series P43 Lower Pump Repair Kit P43

11 Package Contents (-2 Same except Follower is ) 43:1 Ratio, Carbon Steel Extrusion Package P Carbon Steel Pump Carbon Steel Follower Plate B Single Post Ram Optional Portability Kit Basic Pump Performance 11 Air Inlet Pressure Range bar Fluid Pressure Range bar 75 Cycles/Minute: l/min Displacement Per Cycle cm 3 Lower Pump Material Carbon Steel Plunger Material St. Steel (Chrome Plated) Air Motor Air Motor Repair Kit Lower Pump End Series P43 Lower Pump Repair Kit P43 Package Contents :1 Ratio, Stainless Steel Extrusion Package P Stainless Steel Pump Stainless Steel Follower Plate B Single Post Ram Optional Portability Kit Basic Pump Performance Air Inlet Pressure Range bar Fluid Pressure Range bar 75 Cycles/Minute: l/min Displacement Per Cycle cm 3 Lower Pump Material Stainless Steel Plunger Material St. Steel (Chrome Plated) Air Motor Air Motor Repair Kit Lower Pump End Series P43 Lower Pump Repair Kit P43 Package Contents NP443R :1 Ratio, Carbon Steel Extrusion Package P Carbon Steel Pump B Two-Post Mini Ram Follower Plate R Regulator Muffler Basic Pump Performance Air Inlet Pressure Range bar Fluid Pressure Range bar 60 Cycles/Minute: l/min Displacement Per Cycle cm 3 Lower Pump Material Carbon Steel Plunger Material St. Steel (Chrome Plated) Air Motor Air Motor Repair Kit Lower Pump End Series P43 Lower Pump Repair Kit P X-1 Shown with optional Stop & Bracket Assembly Kit NP443R01-1 Extrusion Packages This package can use 60 kg drums with a maximum height of 700mm

12 12 Extrusion Systems (Ordering) Series 4-1/4 Air Motor Pump Information 21 30:1 Stnls. Steel 2-Ball Pump ( X43) 22 22:1 Stnls. Steel 2-Ball Pump ( X43) 24 11:1 Stnls. Steel 2-Ball Pump ( X43) 31 23:1 Carbon Steel Chop Check Pump ( X43-B) 34 12:1 Carbon Steel Chop Check Pump ( X43-B) Follower Options 02 Aluminum Follower Plate with Polyurethane Double- Lipped Seal 52 Teflon Coated Aluminum Follower Plate with Polyurethane Double-Lipped Seal Popular Model Example: NP431R-02-G43 Packages include Pump, X Ram, Follower Plate Assembly, Filter/Regulator-Lubricator Kit, Air Motor Muffler & 90 Outlet Elbow. Extrusion Packages To get the desired pump ration and follower options, replace the X with appropriate numbers from the Pump Information, Follower Options and Packing Options Charts. NP4 XXR - XX - XXX Packing Options G43 R43 UHMW-PE/Leather Staggered Teflon/UHMW-PE Staggered (Upper) Teflon (Lower) NP431R-X

13 Extrusion Systems (Ordering) Packages include Pump, X Ram, Follower Plate Assembly, Filter-Regulator-Lubricator Kit, Air Motor Muffler & 90 Outlet Elbow. To get the desired pump ration and follower options, replace the X with appropriate numbers from the Pump Information, Follower Options and Packing Options Charts. NP6 XXR - XX - XXX 13 Series 6 Air Motor Pump Information 21 60:1 Stnls. Steel 2-Ball Pump ( X43) 22 45:1 Stnls. Steel 2-Ball Pump ( X43) 24 23:1 Stnls. Steel 2-Ball Pump ( X43) 31 46:1 Carbon Steel Chop Check Pump ( X43-B) 34 23:1 Carbon Steel Chop Check Pump ( X43-B) Packing Options G43 R43 Follower Options UHMW-PE/Leather Staggered Teflon/UHMW-PE Staggered (Upper) Teflon (Lower) 02 Aluminum Follower Plate with Polyurethane Double-Lipped Seal 52 Teflon Coated Aluminum Follower Plate with Polyurethane Double-Lipped Seal Popular Model Example: NP624R-02-G43 Packages include Pump, X Ram, Follower Plate Assembly, Filter-Regulator-Lubricator Kit, Air Motor Muffler & 90 Outlet Elbow. NP8 XXR - XX - XXX Series 8 Air Motor Pump Information 34 44:1 Carbon Steel Pump ( X47-B) G43 R43 Follower Options Packing Options UHMW-PE/Leather Staggered Teflon/UHMW-PE Staggered (Upper) Teflon (Lower) 02 Aluminum Follower Plate with Polyurethane Double-Lipped Seal 52 Teflon Coated Aluminium Follower Plate with Polyurethane Double-Lipped Seal NP834R-02-G43 Extrusion Packages

14 14 Model Pumps Number Description Used With Floor Mounts Floor Mount - Accepts suction line & 6 air motor, 2-ball and from bulk containers or mixing tanks. extrusion pumps. Also 8 3 NPT(F) inlet. 1/4 NPT(F) 38:1 2-ball and 44:1 vent port with plug. extrusion pumps Floor Mount - Accepts suction line 8, 10 and 12 air motor 2-ball from bulk containers or mixing tanks. and extrusion pumps. Except 3 NPT(F) inlet. 1/4 NPT(F) vent 8 38:1 2-ball and 44:1 port with plug. extrusion pumps. Model Number Description Bulk/Tote Tank Supply Components A Material Supply Hose - Heavy duty (25mm diameter) hose features neoprene construction with a 340 bar max. working pressure capacity. Both ends 1 NPT(M). Length: 2.1 m. B Ball Valve - For use with material supply hose. 306 bar max. working pressure rated. B C A D C X Material Hose With Fittings - 76mm diameter hose has cross-linked polyethylene (internal) and neoprene (external) construction. Hose comes with female cam-lever locking coupler, male adapter, cam-lever locking dust cap and dust plug. Length: 0.6 m ( ), 1.2m ( ) & 1.8m ( ). Maximum working pressure: 125 psi D 65138, Pump Floor Mount - See above for floor mount information Model Used Follower Plate Number Description With Used With Rams for 19 or 60 litre Drums B Two Post Ram N Series 22:1 & (19 or 60 litre drums) air motor pumps Extrusion Accessories B B Single Post Ram - For use with N Series X, materials up to 1,000,000 CPS viscosity. 22:1 pumps or Follower For 19 litre containers. Hold-down & air motor Plates clamps secure pail Portability Kit 43:1 extrusion available for mobile applications. pump Portability Kit - Mounts directly to B the base of the B Ram, to Single Post allow ease of portability. Will clear Rams and 711 mm openings. Has Ram packages 305 mm tyres Stop & Bracket Kit Assembly - To secure pail to ram base. NOTE: Order mounting plate separately to mount a NM2304B-11-XXX on the ram B

15 Model Used Follower Plate Number Description With Used With 15 Rams for 19 or 208 litre drums Two Post Ram - For use with materials & Follower over 200,000 CPS viscosity. Consists of air motor Plate. two 3-1/2 diameter air cylinders joined by Integrity pumps. For 19 litre cross-over tubes and welded to a steel Also 8 air motor containers use base. Cast aluminum follower plate has 44:1 extrusion double edge Buna N wiper to clean drum pumps & 40:1 Follower Plate. and seal material from atmosphere. Integrity Base is 991 mm x 610 mm. pumps. Raised height is 2.5 m Lowered position is 1.6 m Two Post Ram - Same as , Same as above except follower plate has Telfon coating Two Post Ram - Same as Same as above except for polyurethane wiper Two Post Ram - Same as , Same as above except follower plate has Telfon coating Two Post Ram - Same as Same as above except for EPR wiper Two Post Ram - Same as , Same as above except follower plate has Telfon coating Two Post Ram - Same as , 10, except for the mounting for larger pumps air motor extrusion and Follower Plate. pump. Except 8 44:1 extrusion pump & 40:1 Integrity pumps Two Post Ram - Same as , Same as above except follower plate has Telfon coating Two Post Ram - Same as , Same as above except for polyurethane wiper Two Post Ram - Same as , Same as above except follower plate has Telfon coating Two Post Ram - Same as Same as above except for EPR wiper Two Post Ram - Same as , Same as above except follower plate has Telfon coating Two Post Ram - Same as & 6 air motor except follower plate has two EPR 2-ball & extrusion tube type wiper seals. pumps. Also 8 air motor 44:1 extrusion pumps & 40:1 Integrity pumps Two Post Ram - Same as , Same as above except follower plate has Telfon coating Two Post Ram - Same as , Same as above except for Neoprene wiper seals Two Post Ram - Same as , Same as above except plate has Telfon coating Two Post Ram - Same as , Same as above except for Viton wiper seals X Extrusion Accessories

16 16 Model Used Follower Plate Number Description With Used With X Two Post Ram - Same as , & 6 air motor except follower plate has Teflon coating. Integrity pumps pumps. Also 8 air motor 44:1 extrusion pumps & 40:1 Integrity pumps Two Post Ram - Same as , 10 & 12 air except follower plate has two EPR motor extrusion pumps. tube type wiper seals. Except 8 44:1 extrusion & 40:1 Integrity pumps Two Post Ram - Same as , Same as above except follower plate has Telfon coating Two Post Ram - Same as , Same as above except for Neoprene wiper seals Two Post Ram - Same as , Same as above except plate has Telfon coating Two Post Ram - Same as , Same as above except for Viton wiper seals Two Post Ram - Same as , Same as above except plate has Telfon coating Pump Stabilising Brackets - Attaches 8, 10, 12 easily to Ram. Kit includes hardware. Air Motor Pumps Pump Stabilising Brackets - Same as & except fits smaller pumps. Air Motor Pumps Drum Hold-Down Brackets - Kit includes 2 brackets, clamp screws, nuts Extrusion Accessories Rams (Continued) Pump/Drum Stabilising Brackets

17 Model Follower Pumps Number Model No. Material Used With 17 Extra Heavy-Duty Rams 208 litre Containers The X extra heavy-duty ram features 139mm diameter post construction capable of delivering bar* follower down force. This extra measure of down force makes the Ram the best choice for the hard-duty supply of heavy inks, RTV silicones, caulkings, varnishes, highly viscous adhesives and much more Buna N 4 1 4, 6 air motor Chop Check and Two-Ball pumps. 8 air motor 44:1 Chop Check and 40:1 Integrity pumps Polyurethane same as Buna N 8,10 and 12 air motor Chop Check and Two-Ball pumps, except 8 air motor 44:1 and 40:1 Integrity pumps Polyurethane same as EPR same as * WARNING: Before using maximum follower down force, check container or consult container manufacturer for maximum pressure rating. The Ram / Lift provides responsive pump lifting and pump lowering with sufficient downforce to permit pump extrusion of materials up to 500,000 c.p.s. Its ability to revolve 360-degrees allows the ongoing placement and rotation of three, 208 litre containers a critical feature in applications that demand continuous material supply X Model Fits Height Height Air Number ARO Pump Raised Lowered Inlet Single Post Rams /4-6 Air Motors 2.8 m 1.6 m 1/4 NPT to 12 Air Motors 2.8 m 1.6 m 1/4 NPT Small Hydraulic Motor 2.8 m 1.6 m 1/4 NPT Large Hydraulic Motor 2.8 m 1.6 m 1/4 NPT The above models include the brackets and hardware needed to accommodate two-ball or extrusion tie-rod style pumps (Pump sold separate) (Pump, Follower, and Follower Assist Kit sold separate) Extrusion Accessories

18 18 Model Ram or Lift Follower Plate Number Description Used With Used With Follower Plates 19 litre Containers Follower Plate - Carbon , X &6 steel with Buna N wiper. & B Rams Integrity* or Lift pumps Follower Plate - Electroless B NM2322X-11-X, nickel-plated with double-edge Rams air motor Buna N wiper and seal. 9:1 & 46:1 pumps Follower Plate - Electroless , NM2304B-11-X, nickel-plated with double-edge & B air motor polyurethane wiper and seal. Rams 9:1 & 46:1 pumps Follower Plate - Electroless , NM2322X-11-X, nickel-plated with double-edge B air motor EPR wiper and seal. Rams 9:1 & 46:1 pumps Follower Plate - Electroless , & 6 air nickel-plated with double-edge B motor Integrity Buna N wiper and seal. Rams pumps. Also 8 air motor 44:1 extrusion pumps & 40:1 Integrity* pumps Follower Plate - Electroless , & 6 air motor nickel-plated with double-edge B Integrity pumps. polyurethane wiper and seal. Rams Also 8 air motor 44:1 extrusion & 40:1 Integrity* pumps Follower Plate - Electroless , & 6 air motor nickel-plated with double-edge B Integrity pumps. EPR wiper and seal. Rams Also 8 air motor 44:1 extrusion & 40:1 Integrity* pumps. Extrusion Accessories Follower Plate - Carbon steel B NM2322X-11-X. with 290-mm polyethylene - Rams Replaces urethane wiper seal Follower Plate - Carbon Steel B NM2322X-11-X. with 295-mm nitrile seal. Rams Replaces Designed for metric pails Follower Plate - Carbon Steel, B NM2322X-11-X. with mm polyethylene - Rams Replaces urethane wiper seal. Designed for metric pails Follower Plate - Stainless Steel B NM2304B-11-X with 290-mm polyethylene - Rams & air motor urethane wiper seal. 43:1 pumps Follower Plate - Stainless Steel B Integrity with 290-mm polyethylene - Rams pumps urethane wiper seal. (No adapter required) * Requires Follower Plate Adapter. Accessories Seal Protectors - Package of 10 for 19 litre followers 19 litre to be inserted between the follower plate and the material Follower Plates in the container. This helps to prevent corrosive materials from attacking the wiper and reduces clean-up time Follower Plate Adapter - For attaching Integrity & to follower plates or floor stand. Includes stainless Followers. steel adapter w/2 NPT(F) threads, seal and hardware ,-2,-3 Rams Floor Mounts

19 Model Rams Pumps Number Description Used With Used With 19 Follower Plates 208 litre Containers Follower Plate - Single lip X Ram & 6 air Buna N wiper with polyethylene Lift motor 2-ball & back-up. extrusion pumps Follower Plate - Same as 66248, Same as above Same as above except with polyethylene wiper Follower Plate - Cast Aluminum X, & 6 air with double-edged X motor 2-ball & Buna N wiper & seal. extrusion pumps Also 8 air motor 40:1 Integrity & 44:1 extrusion pumps Follower Plate - Same as Same as above Same as above 66516, except follower plate has Teflon coating Follower Plate - Same as Same as above Same as above 66516, except with polyurethane wiper & seal Follower Plate - Same as Same as above Same as above , except follower plate has Teflon coating Follower Plate - Same as Same as above Same as above 66516, except with EPR wiper & seal Follower Plate - Same as, Same as above Same as above except follower plate has Teflon coating Follower Plate - Cast X, 8, 10 & 12 air Aluminum with double X motor extrusion edge Buna N wiper and seal. pumps. Except 8 40:1 Integrity & 44:1 extrusion pumps Follower Plate - Same as Same as above Same as above 66517, except follower plate has Teflon coating Follower Plate - Same as Same as above Same as above 66517, except with polyurethane wiper & seal Follower Plate - Same as Same as above Same as above , except follower plate has Teflon coating Follower Plate - Same as Same as above Same as above 66517, except with EPR wiper & seal Follower Plate - Same as Same as above Same as above , except follower plate has Teflon coating Follower Plate - Cast Aluminum X, & 6 air motor with two EPR tube type wiper X 2-ball & extrusion seals. pumps. Also 8 40:1 Integrity & 44:1 extrusion pumps Follower Plate - Same as Same as above Same as above , except follower plate has Teflon coating X Extrusion Accessories

20 20 Model Rams Pumps Number Description Used With Used With 6719X-X Follower Plates 208 litre Containers Follower Plate - Same as X, & 6 air motor , except with Neoprene X 2-ball & extrusion wiper seals. pumps. Also 8 40:1 Integrity & 44:1 extrusion pumps Follower Plate - Same as Same as Same as , except follower plate previous previous has Teflon coating Follower Plate - Same as Same as Same as , except with Viton wiper seals. previous previous Extrusion Accessories Follower Plate - Same as Same as Same as , except follower plate previous previous has Teflon coating Follower Plate - Cast Aluminum X, 8, 10 & 12 air with two EPR tube type wiper X motor extrusion seals. pumps. Except 8 40:1 Integrity & 44:1 extrusion pumps Follower Plate - Same as Same as above Same as above , except follower plate has Teflon coating Follower Plate - Same as Same as above Same as above , except with EPR wiper seals Follower Plate - Same as, Same as above Same as above except follower plate has Teflon coating Follower Plate - Same as Same as above Same as above , except with Viton wiper seals Follower Plate - Same as Same as above Same as above , except follower plate has Teflon coating. Seal Protectors Seal Protectors - Package of 10 for 208 litre followers 208 litre to be inserted between the follower plate and the material Follower in the container. This helps to prevent corrosive materials Plates from attacking the wiper and reduces clean-up time. Model Ram Number Description Used With Pump Follower/Floor Stand Adapters Follower Plate Adapter X & 6719X-X Followers For attaching NM2322X-X & , -2, -3, X 6712X-P43 pumps to 55-gal. and X Rams. follower plates or floor stands Floor Mount Follower Plate Adapter & For attaching Integrity pumps Followers. to follower plates or floor stand , -2, -3 Rams Includes stainless steel adapter w/ Floor Mount NPT(F) threads, seal and hardware.

21 Regulated Working Maximum Gauge Base Pressure Pressure Inlet Pressure Model Housing Seat Range W/Gauge Pressure Range Number (See code at bottom) bar bar bar bar 21 Downstream Fluid Regulators 3/8 ports, standard flow to 11.4 litres Gauge Included A1A-B C/S T/C A1B-B C/S T/C A3A-B S/S T/C A3B-B S/S T/C /8 ports, high-flow to 22.7 litres B1D-B Z/A T/C B1E-B Z/A T/C B3D-B S/S T/C B3E-B S/S T/C Gauge Included B1A-B C/S T/C B1B-B C/S T/C B3A-B S/S T/C B3B-B S/S T/C /8 Ports Model 3/4 ports, mastic-flow to 75.7 litres** C1C-B C/S T/C C3B-B S/S T/C /8 ports, remote models, flow to 22.7 litres * B4R-B S/S 3/S B1R-B C/S T/C B3R-B S/S T/C Gauge NOT Included. ** Flow rates tested in 30 wt. oil. 3/4 Ports Model 3/4 ports, remote models, mastic-flow to 75.7 litres** C1R-B C/S T/C C3R-B S/S T/C ** Flow rates tested in 55 CPS material. Code Description Code Description High Pressure Remote Model Material Codes 3/S 300 Series Stainless Steel T/C Tungsten Carbide 4/S 400 Series Stainless Steel S/S Stainless Steel C/S Carbon Steel Z/A Zinc Aluminum Z Zinc Code Description Material Fluid Regulator Gauges / Adapters Gauge, bar Stainless Steel Gauge, bar Non-Stainless Steel Gauge, bar Non-Stainless Steel Adapter, 3/8 Dual Outlet Ports Adapter, 3/4 Single Outlet Ports Extrusion Accessories

22 22 Max. Fluid Fluid Fluid Outlet Working Model Pressure Inlet I.D. & Thread Pressure Number Description Bar in mm Bar Extrusion Accessories XX X XX-B XX-B Automatic Extrusion Guns Flow Gun - Requires 345 3/8 6 & (2) 3.4 at 4-way air valve to open NPT 11/ /8 F 138 bar and close. Adjusting (F) (2) (M) fluid screw varies stroke length. pressure Secures to 1/2 diameter rod by allen screw. Aluminum body with tungsten carbide seats. Order XX Extrusion Nozzle Kit separately B Flow Gun - Has air 345 1/4 2.3 & 1/8 3.4 at open, spring return NPS 11/16-16 (F) 138 bar cylinder. Requires (M) (M) fluid 3-way air valve to open. pressure Adjusting screw varies stroke length. Secures to 1/2 diameter rod by allen screw. 316 stainless steel with tungsten carbide seat. Order XX Extrusion Nozzle Kit separately Snuff-Back Gun - High 345 3/8 1/4 (2) flow automatic dispensing NPT NPT 1/8 gun is designed to handle (F) (F) NPT (F) high-viscosity materials. (2) Requires a 4-way air valve to open and close Flow Gun - Similar to 345 3/8 3/8 (2) 3.4 at except with carbon NPT 18 (M) 1/8 138 bar steel body and has ball (F) NPT (F) fluid seat located at material inlet pressure of valve seat assembly. Model Orifice Model Orifice Model Orifice Number Diameter Nimber Diameter Number Diameter Extrusion Gun Nozzle Kits XX Extrusion Nozzle Kit - Used on manual or automatic extrusion guns. Hardened steel assembly includes nozzle and cap. 11/16-16 UN(F) Maximum Fluid Filter Filter Model Pressure Filter Inlet(s) Size Outlet(s) Size Number Bar Mesh Microns (Qty) NPT (Qty) NPT Material Filters-Standard Models 1/4 fluid inlet/carbon steel construction /4-F (2) 1/4-F (3) Bottom swivel /4-F (2) 1/4-F (3) Side swivel /4-F (2) 1/4-F (3) 1/2 fluid inlet/stainless steel construction (passivated) /2-F (2) 1/2-F (1) /2-F (2) 1/2-F (1) /2-F (2) 1/2-F (1) 1/2 fluid inlet/carbon steel construction (e-nickel plated)) /2-F (2) 1/2-F (1) /2-F (2) 1/2-F (1) /2-F (2) 1/2-F (1) Dual Screens 1-8 3/4-F (1) 1 fluid inlet/carbon steel construction (e-nickel plated)) B F (2) 3/8-F (3) B F (2) 3/8-F (3) B F (2) 3/8-F (3)

23 Max Fluid Fluid Fluid Outlet Model Pressure Inlet I.D. & Thread Number Description bar In. mm 23 Manual Extrusion Guns * Flow Gun - Aluminum body with 517 3/8 (F) 6 & tungsten carbide seats. Used to 11/16-16 (M) extrude material over 200,000 CPS. Order XX Extrusion Nozzle Kit separately Flow Gun - Wetted parts of /4 2.3 & series stainless steel with tungsten NPS(M) 11/16-16 (M) carbide seats. Used to extrude material up to 200,000 CPS. Order XX Extrusion Nozzle Kit separately Flow Gun - Wetted parts of /8 (F) 6 & Series stainless steel with Teflon 1/4 NPT(F) packings. Used to extrude material over 200,000 CPS. Order Adapter and XX Extrusion Nozzle Kit separately. *WARNING: Do not use with halogenated hydrocarbons. This model contains aluminum parts that come in contact with the material being dispensed. Aluminum is not compatible with halogenated hydrocarbon solvents Extrusion Gun Nozzle Kits Adapter - 1/4NPT(M) to 11/16-16(M) adapts XX Extrusion Nozzle Kit to fluid outlet for Flow Guns XX Extrusion Nozzle Kit - Used on manual or automatic extrusion guns. Hardened steel assembly includes nozzle and cap. 11/16-16 UN(F). For orifice diameter, see chart on previous page. Model Thread Size Type Max. Working Number In. NPT x NPT of Seals Pressure bar (Shown with XX) XX Swivels Swivels are used to give mobility and flexibility for material hoses and dispensing guns. Select the proper working pressure and check the compatibility of the seals with the material being pumped. straight /8 (M) x 1/8 (F) Fabric with Neoprene /8 (M) x 1/8 (F) Fabric with Neoprene /8 (M) x 3/8 (F) Fabric with Neoprene /2 (M) x 1/2 (F) Fabric with Neoprene /4 (M) x 3/4 (F) Fabric with Neoprene 69 Z /8 (M) x 1/8 (F) Fabric with Neoprene /8 (M) x 1/4 (F) Fabric with Neoprene /8 (M) x 3/8 (F) Fabric with Neoprene /2 (F) x 3/8 (M) Fabric with Neoprene B* 1/4-18 NPT (F) x 1/4-18 NPT (M) Fabric with Neoprene B 1/4-18 NPT (F) x 1/4-18 NPT (M) Fabric with Neoprene 345 * Includes internally mounted element Extrusion Accessories

24 24 Pumps Port Reg. Pressure Max. Model Used Size Range Flow Number Description With NPT bar Pressure Air Filter/Regulator/Lubricator MINIATURE F/R/L Filter/Regulator/Lubricator 2 & 3, 1/4 (F) dm 3 /s Drop/fog-type lubrication, air motor 20 micron filter, pumps polycarbonate bowls C Filter/Regulator 2 & N, 1/4 (F) dm 3 /s Drop/fog-type lubrication, air motor 20 micron filter, pumps polycarbonate bowls. MODULE/AIR 2000 F/R/L C Filter/Regulator/Lubricator & 1/2 (F) dm 3 /s Drop/fog-type lubrication, 6 air 40 micron filter, motor metal bowls w/ sight glass. pumps P Filter/Regulator & 6 1/2 (F) dm 3 /s Drop/fog-type lubrication, air motor 40 micron filter, pumps metal bowls w/ sight glass. HEAVY DUTY F/R/L Filter/Regulator/Lubricator 8, 10 3/4 (F) dm 3 /s Drop/fog-type lubrication, & micron filter, air motor polycarbonate bowls. pumps F/R/L Assemblies Kit Assembly 8, 10, 3/4 (M) dm 3 /s Heavy-Duty FRL w/ hose & 12 & mounting bracket for air motor installation to Two Post pumps Ram Kit Assembly & 1/2 (M) dm 3 /s Heavy-Duty FRL w/ hose 6 air & mounting bracket for motor installation to Two Post pumps Ram. Extrusion Accessories C Air Line Lubricant One Quart Bottle - A high quality EP extreme pressure gear oil, nondetergent, rust or oxidation inhibited, with a viscosity of S.U.S. at F.

25 Pumps Air Air Pressure Model Used Inlet Outlet Range Number Description With NPT NPT bar 25 Over-run Controls ARO-STOP Valve N Series, 1/4 (F) 1/4 (M) Shuts off air to the pump air motor when material container is pumps empty or line is broken. only Quick set and reset feature ARO-STOP Valve & 1/2 (F) 1/2 (M) Shuts off air to the pump 6 air when material container is motor empty or line is broken. pumps Quick set and reset feature ARO-STOP Valve 8", 10 3/4 (F) 3/4 (M) Shuts off air to the pump & 12 when material container is air motor empty or line is broken. pumps Quick set and reset feature. only Pump Air Size Model Used Inlet Number Description With NPT mm x mm Air Motor Muffler Air Motor Muffler & 6 1-1/4 (M) 89 x 284 Reduces air exhaust noise level air motor to acceptable OSHA standards. pumps Air Motor Muffler 8 air motor, 1-1/4 (M) 143 x 391 Reduces air exhaust noise level pumps to acceptable OSHA standards Air Motor Muffler 10 & 12 Bolted-on 229 x 508 Reduces air exhaust noise level air motor, to acceptable OSHA standards. pumps Model Used Number Description With Wet Sol Plus B Wet Sol - One litre Container All pumps with wet cups. Designed to prolong packing life by keeping the piston rod and packings wetted. Also reduces the possibility of material hardening on the piston rod B Wet Sol litre Container B Extrusion Accessories

26 26 Five Simple Steps to the Right ARO Pump. 1 Pump Style This identifies the type of pump. You can also identify the pump s ratio and the maximum fluid pressure the pump can produce. 2 Pump Performance Here you can locate information on the performance of each pump model. This includes air inlet and fluid pressure ranges, maximum recommended cycles and displacement per cycle. Also, use this area to locate data on flow and noise levels. A photo of each model provides dimensional data. 3 Pump Motor/Lower Specifications Important specifications for each pump are conveniently located in one area. Service kits for the air motor and lower end are listed. This section also contains data needed to spec a pump into a specific system, if necessary. 4 Pump Packings - Ordering Pump Style Ratio:? PSI:?? (Max.) Type:? 5 ARO offers several types of lower end packings in an effort to meet the performance demands of different applications. Not all packing types are available on each pump. Use this section to select the appropriate packing set-up for your application. The ordering menu easily identifies which packings can be chosen. Recommended Accessories ARO offers many accessories that can improve the performance of the pump you ve selected. Several of these accessories are listed along with each pump. There is also a complete listing of accessories at the end of each section. That way the accessories most often needed for an application are easily accessible.

27 Performance 27 Air Inlet Pressure Range Fluid Pressure Range Max. Rec d Cycles Per Minute Displacement Per Cycle Cycles Per Gallon Cycles / Minute Noise Psi Specifications Lower Pump Material Plunger Material Cylinder Material Air Motor Motor Repair Kit Motor Diameter Stroke Air Inlet Lower Pump End Series Lower Pump Repair Kit Material Inlet Material Outlet Weight NM2322E-11-P4X Ordering Recommended Accessories N M E P 4 X Packing / Plunger 3 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE Grooved Piston (Lower) 8 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE Single Lip Cup (Lower) Air F/R/L: Airline Oil: Wet Sol: B Follower Plate: Page 18 A.S.A.P. Packages: NM322R01-1 NP322L Pump Style Ratio:? Bar:?? (Max.) Type:?

28 X4X Performance 4-1/4", 11:1, 2-Ball Air Inlet Pressure Range bar 4-1/4" (11:1) 9 mm Fluid Pressure Range bar Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Litre Cycles / Minute l/min Noise 4 bar db(a) Specifications Lower Pump Material CF-8M Stnls. Steel Plunger Material See Plunger Options Below Cylinder Material See Plunger Options Below Air Motor B Motor Repair Kit Motor Diameter cm (4-1/4 ) Stroke mm 481 mm 322 mm Air Inlet /2 NPT(F) Lower Pump End Series X4X Lower Pump Repair Kit X4X Material Inlet NPT(F) / 2 NPT(M) Material Outlet NPTF-1(F) Weight kg Recommended Accessories Air F/R/L: C Airline Oil: Air Motor Muffler: Wet Sol: B Wall Mount: 66 Floor/Follower Adapter: Floor Mount: Ordering X 4 X Packings Plungers 3 : Teflon 3 : 17-4 Stnls. Steel, C : UHMW-PE Hard Chrome Plated G : UHMW-PE/Leather B : 17-4 Stnls. Steel, P : UHMW-PE/Leather (Upper), Ultra Coated UHMW-PE (Lower) R : Teflon/UHMW-PE (Upper), Teflon (Lower) COATING Piston Pumps Ratio: 11:1 Bar: (Max.) Type: 2-Ball Fluid Pressure (Bar) CYCLES PER MINUTE Performance based on 5 poise oil at ambient temperature 8.3 bar bar Air Consumption (litres/sec.) LITRES PER MINUTE DELIVERY

29 Fluid Pressure (Bar) Performance 4-1/4", 12:1, Chop Check Air Inlet Pressure Range bar Fluid Pressure Range bar Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Litre Cycles / Minute l/min Noise 4 bar db(a) w/muffler Specifications Lower Pump Material Carbon Steel (Nickel Plated) Plunger Material Stnls. Steel (Hard Chrome Plated) Cylinder Material Carbon Steel (Nickel Plated) Air Motor B Motor Repair Kit Motor Diameter /4 Stroke mm Air Inlet /2 NPT(F) Exhaust Port /4 NPT(F) Chop Check Pump Model X43-B Lower Pump Repair Kit X43-B Material Inlet Flange Mount Material Outlet NPT(F) Weight kg Ordering X B Packings G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-(Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) CYCLES PER MINUTE Performance based on 90 wt. gear oil at ambient temperature 8.3 bar LITRES PER MINUTE DELIVERY 8.3 bar Air Consumption (litres/sec.) mm X43-B mm mm Recommended Accessories Air F/R/L: C Airline Oil: Air Motor Muffler: Wet Sol: B Floor Mount: Rams: Page 15 Ratio: 12:1 Bar: (Max.) Type: Chop Check /4" (12:1) CS Extrusion Pumps

30 30 8" (13:1) CS Extrusion Pumps Ratio: 13:1 Bar: (Max.) Type: Chop Check XX4-B mm 508 mm Recommended Accessories Air F/R/L: Airline Oil: Air Motor Muffler: Wet Sol: B Floor Mount: Ram: Page mm Fluid Pressure (Bar) Performance 8", 13:1, Chop Check Air Inlet Pressure Range bar Fluid Pressure Range bar Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Litre Cycles / Minute lpm Noise 4 bar db(a) w/muffler Specifications Lower Pump Material Carbon Steel (Nickel Plated) Plunger Material Carbon Steel (Chrome Plated) Cylinder Material Carbon Steel (Nickel Plated) Air Motor Motor Repair Kit Motor Diameter Stroke mm Air Inlet /4 NPT(F) Exhaust Port /4 NPT(F) Chop Check Pump Model XX4-B Lower Pump Repair Kit XX4-B Material Inlet Flange Mount Material Outlet /2 NPT(F) Weight kg Ordering X X 4 - B Packings / Springs F4 : UHMW-PE/Leather Staggered (Upper), UHMW-PE (Lower), Multiple Wave Spring J3 : Polyurethane (Upper), UHMW-PE (Lower), No Spring P4 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower), Multiple Wave Spring R4 : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) Multiple Wave Spring CYCLES PER MINUTE bar Performance based on 90 wt. gear oil at ambient temperature 8.3 bar LITRES PER MINUTE DELIVERY Air Consumption (litres/sec.)

31 Fluid Pressure (Bar) Performance 10", 20:1, Chop Check Air Inlet Pressure Range bar Max. Fluid Pressure Range bar Max. Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Litre Cycles / Minute l/min Noise 4 bar db(a) w/muffler Specifications Lower Pump Material Carbon Steel (Nickel Plated) Plunger Material Carbon Steel (Chrome Plated) Cylinder Material Carbon Steel (Nickel Plated) Air Motor Motor Repair Kit Motor Diameter Stroke mm Air Inlet /4 NPT(F) Exhaust Port /4 NPT(F) Chop Check Pump Model XX4-B Lower Pump Repair Kit XX4-B Material Inlet Bolted Flange Material Outlet /2 NPT(F) Weight kg Ordering 20 CYCLES PER MINUTE X X 4 - B Packings / Springs F4 : UHMW-PE/Leather Staggered (Upper), UHMW-PE (Lower), Multiple Wave Spring J3 : Polyurethane (Upper), UHMW-PE (Lower), No Spring P4 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower), Multiple Wave Spring R4 : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) Multiple Wave Spring Performance based on 90 wt. gear oil at ambient temperature LITRES PER MINUTE DELIVERY Air Consumption (litres/sec.) mm XX4-B 508 mm Recommended Accessories Air F/R/L: Airline Oil: Air Motor Muffler: Wet Sol: B Floor Mount: Rams: Page mm Ratio: 20:1 Bar: (Max.) Type: Chop Check 31 10" (20:1) CS Extrusion Pumps

32 32 4-1/4" (22:1) CS 9 mm X4X 481 mm 322 mm Performance 4-1/4", 22:1, 2-Ball Air Inlet Pressure Range bar Fluid Pressure Range bar Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Litre Cycles / Minute l/min Noise 4 bar db(a) Specifications Lower Pump Material CF8M (316) Stainless Steel Plunger Material See Plunger Options Below Cylinder Material See Plunger Options Below Air Motor B Motor Repair Kit Motor Diameter /4 Stroke mm Air Inlet /2 NPT(F) Exhaust Port /4 NPT(F) Two-Ball Pump Model X4X Lower Pump Repair Kit X43 Material Inlet NPT(F) 2 NPT(M) Material Outlet NPT(F) Weight kg Piston Pumps Ratio: 22:1 Bar: (Max.) Type: 2-Ball Recommended Accessories Air F/R/L: C Airline Oil: Air Motor Muffler: Wet Sol: B Wall Mount: 66 Floor/Follower Adapter: Floor Mount: Fluid Pressure (Bar) Ordering CYCLES PER MINUTE Performance based on 5 poise oil at ambient temperature bar bar X 4 X Packings 3 : Teflon C : UHMW-PE G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) Plungers 3 : 17-4 S. S. Hard Chrome Plated B : 17-4 S.S. Ultra Coated COATING LITRES PER MINUTE DELIVERY Air Consumption (litres/sec.)

33 Fluid Pressure (Bar) Performance 3", 22:1, Chop Check Air Inlet Pressure Range bar Fluid Pressure Range bar Displacement Per Cycle cm 3 Cycles Per Litre Maximum Working Flow l/min Noise 6.8 bar db(a) Specifications Lower Pump Material Carbon Steel Plunger Material Stnls. steel Air Motor Motor Repair Kit Motor Diameter Stroke mm Air Inlet /4 NPTF-1 (f) Pump Model: Model NM2322E-11-P P43 Model NM2322E-11-P P48 Lower Pump Repair Kits: Model NM2322E-11-P P43 Model NM2322E-11-P P48 Material Inlet Follower Plate Mounted Material Outlet /2 NPT(F) Weight kg Ordering N M E P 4 X Packing / Plunger 3 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE Grooved Piston (Lower) 8 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE Single Lip Cup (Lower) CYCLES PER MINUTE Performance based on 30 wt. gear oil at ambient temperature bar 8.3 bar LITRES PER MINUTE DELIVERY 4 2 Air Consumption (litres/sec.) NM2322E-11-P4X 857 mm 621 mm 430 mm 360 mm Recommended Accessories Air F/R/L: Airline Oil: Wet Sol: B Follower Plate: See Page 18 A.S.A.P. Packages: NM322R01-1 NP322L01-1 Ratio: 22:1 Bar: (Max.) Type: Chop Check 33 3" (22:1) CS Extrusion Pumps

34 34 3" (22:1) SS Extrusion Pumps Ratio: 22:1 Bar: (Max.) Type: Chop Check NM2322F-11-P4X 857 mm 621 mm 430 mm 360 mm Recommended Accessories Air F/R/L: Airline Oil: Wet Sol: B Follower Plate: A.S.A.P. Packages: NP322R02-1 NP322L02-1 Fluid Pressure (Bar) Performance 3", 22:1, Chop Check Air Inlet Pressure Range bar Fluid Pressure Range bar Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Litre Maximum Working Flow l/min Noise 6.8 bar db(a) Lower Pump Material Stnls. Steel Plunger Material Stnls. Steel (Chrome Plated) Cylinder Material Stnls. Steel (Chrome Plated) Air Motor Motor Repair Kit Motor Diameter Stroke mm Air Inlet /4 NPTF-1 (F) Pump Model: Model NM P P43 Model NM P P48 Lower Pump Repair Kits: Model NM2322F-11-P P43 Model NM2322F-11-P P48 Material Inlet Follower Plate Mounted Material Outlet /2 NPT(F) Weight kg Ordering N M F P 4 X Packing / Plunger 3 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE Grooved Piston (Lower) 8 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE Single Lip Cup (Lower) CYCLES PER MINUTE Performance based on 30 wt. gear oil at ambient temperature bar bar Specifications LITRES PER MINUTE DELIVERY 4 2 Air Consumption (litres/sec.)

35 Fluid Pressure (Bar) Performance 6", 23:1, 2-Ball Air Inlet Pressure Range bar Fluid Pressure Range bar Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Gallon (Litre) Cycles / Minute l/min Noise 4 bar db(a) Lower Pump Material CF8M (316) Stns. Steel Plunger Material See Plunger Option Below Cylinder Material See Plunger Option Below Air Motor B Motor Repair Kit Motor Diameter Stroke mm Air Inlet /2 NPTF Exhaust Port /4 NPTF Two-Ball Pump Model X4X Lower Pump Repair Kit X43 Material Inlet NPT(F) 2 NPT(M) Material Outlet NPTF Weight kg Ordering CYCLES PER MINUTE Performance based on 5 poise oil at ambient temperature bar bar Specifications X 4 X Packings 3 : Teflon C : UHMW-PE G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) Plungers 3 : 17-4 S. S. Hard Chrome Plated B : 17-4 S.S. Ultra Coated COATING Air Consumption (litres/sec.) 9 mm X4X 481 mm 322 mm Recommended Accessories Air F/R/L: C Airline Oil: Air Motor Muffler: Wet Sol: B Wall Mount: 66 Floor/Follower Adapter: " (23:1) SS Ratio: 23:1 Bar: (Max.) Type: 2-Ball 35 Piston Pumps LITRES PER MINUTE DELIVERY

36 36 4-1/4" (23:1) Extrusion Pumps Ratio: 23:1 Bar: (Max.) Type: Chop Check X43-B mm mm mm Recommended Accessories Air F/R/L: C Airline Oil: Air Motor Muffler: Wet Sol: B Floor Mount: Rams: Page 15 Fluid Pressure (Bar) Performance 4-1/4", 23:1, Chop Check Air Inlet Pressure Range bar Fluid Pressure Range bar Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Litre Cycles / Minute l/min Noise 4 bar db(a) Specifications Lower Pump Material Carbon Steel (Nickel Plated) Plunger Material Stainless (Hard Chrome Plated) Cylinder Material Carbon Steel (Nickel Plated) Air Motor B Motor Repair Kit Motor Diameter /4 Stroke mm Air Inlet /2 NPT(F) Exhaust Port /4 NPT(F) Chop Check Pump Model X43-B Lower Pump Repair Kit X43-B Material Inlet Bolted Flange Material Outlet NPT(F) Weight kg Ordering X B CYCLES PER MINUTE Performance based on 90 wt. gear oil at ambient temperature 8.3 bar Packings G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) 8.3 bar LITRES PER MINUTE DELIVERY Air Consumption (litres/sec.)

37 Fluid Pressure (Bar) Performance 6", 23:1, Chop Check Air Inlet Pressure Range bar Fluid Pressure Range bar Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Litre Cycles / Minute l/min Noise 4 bar db(a) w/muffler Specifications Ordering CYCLES PER MINUTE bar Performance based on 90 wt. gear oil at ambient temperature Lower Pump Material Carbon Steel (Nickel Plated) Plunger Material Stnls. Steel (Hard Chrome Plated) Cylinder Material Carbon Steel (Nickel Plated) Air Motor B Motor Repair Kit Motor Diameter Stroke mm Air Inlet /2 NPT(F) Exhaust Port /4 NPT(F) Chop Check Pump Model X43-B Lower Pump Repair Kit X43-B Material Inlet Bolted Flange Material Outlet NPT(F) Weight kg X B Packings G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) LITRES PER MINUTE DELIVERY 8.3 bar Air Consumption (litres/sec.) X43-B mm mm mm Recommended Accessories Air F/R/L: C Airline Oil: Air Motor Muffler: Wet Sol: B Floor Mount: Rams: Page 15 Ratio: 23:1 Bar: (Max.) Type: Chop Check 37 6" (23:1) CS Extrusion Pumps

38 38 12" (30:1) CS Extrusion Pumps Ratio: 30:1 Bar: (Max.) Type: Chop Check XX4-B mm 508 mm 797,7 mm Recommended Accessories Air F/R/L: Airline Oil: Air Motor Muffler: Wet Sol: B Floor Mount: Rams Page 15 Fluid Pressure (Bar) Performance 12", 30:1, Chop Check Air Inlet Pressure Range bar Max. Fluid Pressure Range bar Max. Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Litre Cycles / Minute l/min Noise 4 bar db(a) w/muffler Specifications Lower Pump Material Carbon Steel Plunger Material Carbon Steel Cylinder Material Carbon Steel (Nickel Plated) Air Motor Motor Repair Kit Motor Diameter Stroke mm Air Inlet /4 NPT(F) Exhaust Port /4 NPT(F) Chop Check Pump Model XX4-B Lower Pump Repair Kit XX4-B Material Inlet Bolted Flange Material Outlet /2 NPT(F) Weight kg Ordering X X 4 - B Packings / Springs F4 : UHMW-PE/Leather Staggered (Upper), UHMW-PE (Lower), Multiple Wave Spring J3 : Polyurethane (Upper), UHMW-PE (Lower), No Spring P4 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower), Multiple Wave Spring R4 : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) Multiple Wave Spring CYCLES PER MINUTE Performance based on 90 wt. gear oil at ambient temperature LITRES PER MINUTE DELIVERY Air Consumption (litres/sec.)

39 Fluid Pressure (Bar) Performance 4-1/4", 30:1, 2-Ball Air Inlet Pressure Range bar Fluid Pressure Range bar Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Litre Cycles / Minute l/min Noise 4 bar db(a) Specifications Lower Pump Material CF8M Stnls. Steel Plunger Material See Plunger Options Below Cylinder Material See Plunger Options Below Air Motor B Motor Repair Kit Motor Diameter /4 Stroke mm Air Inlet /2 NPT(F) Exhaust Port /4 NPT(F) Two-Ball Pump Model X4X Lower Pump Repair Kit X43 Material Inlet NPT(F) 2 NPT(M) Material Outlet NPT(F) Weight kg Ordering X 4 X Packings 3 : Teflon C : UHMW-PE G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) Plungers 3 : 17-4 S. S. Hard Chrome Plated B : 17-4 S.S. Ultra Coated COATING CYCLES PER MINUTE Performance based on 5 poise oil at ambient temperature bar 8.3 bar Air Consumption (litres/sec.) X4X 9.3 mm 481 mm 322 mm Recommended Accessories Air F/R/L: C Airline Oil: Air Motor Muffler: Wet Sol: B Floor/Follower Adapter: Floor Mount: /4" (30:1) SS Ratio: 30:1 Bar: (Max.) Type: 2-Ball 39 Piston Pumps LITRES PER MINUTE DELIVERY

40 40 8" (40:1) SS Piston Pumps Ratio: 30:1 Bar: (Max.) Type: 2-Ball X4X 1106 mm 575 mm 322 mm Recommended Accessories Air F/R/L: Airline Oil: Air Motor Muffler: Wet Sol: B Floor/Follower Adapter: Rams: Page 15 Floor Mounts: Fluid Pressure (Bar) Performance 8", 40:1, 2-Ball Air Inlet Pressure Range bar Fluid Pressure Range bar Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Litre Cycles / Minute l/min Noise 4 bar db(a) Lower Pump Material CF8M Stnls. Steel Plunger Material See Plunger Options Below Cylinder Material See Plunger Options Below Air Motor Motor Repair Kit Motor Diameter Stroke mm Air Inlet /4 NPT(F) Exhaust Port /4 NPT(F) Two-Ball Pump Model X47 Lower Pump Repair Kit X43 Material Inlet NPT(F) 2 NPT(M) Material Outlet NPT(F) Weight kg Ordering CYCLES PER MINUTE bar Performance based on 5 poise oil at ambient temperature bar Specifications X 4 X Packings 3 : Teflon C : UHMW-PE G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) Plungers 7 : 17-4 S. S. Hard Chrome Plated C : 17-4 S.S. Ultra Coated COATING Air Consumption (litres/sec.) LITRES PER MINUTE DELIVERY

41 Fluid Pressure (Bar) Performance 4-1/4", 43:1, Chop Check Air Inlet Pressure Range bar Fluid Pressure Range bar Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Litre Cycles / Minute l/min Noise 4 bar db(a) Lower Pump Material Carbon Steel Plunger Material Stnls. Steel (Chrome Plated) Cylinder Material Carbon Steel (Nickel Plated) Air Motor Motor Repair Kit Motor Diameter /4 Stroke mm Air Inlet /2 NPT(F) Exhaust Port /2 NPT(F) Pump Model: Model NM2322E-11-P P43 Model NM2322E-11-P P48 Lower Pump Repair Kits: Model NM2322E-11-P P43 Model NM2322E-11-P P48 Material Inlet Follower Plate Mounted Material Outlet /2 NPT(F) Weight kg Ordering CYCLES PER MINUTE bar Performance based on 30 wt. gear oil at ambient temperature Specifications P 4 X Packing P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) Plungers 3 : HD SS w/chrome plating and standard lower packing 8 : HD SS w/chrome plating and cup type lower packing 8.3 bar Air Consumption (litres/sec.) 5.8 mm P4X 429 mm mm Recommended Accessories Air F/R/L: C Airline Oil: Air Motor Muffler: Wet Sol: B Follower Plate: Page 18 A.S.A.P. Packages: /4" (43:1) CS Ratio: 43:1 Bar: (Max.) Type: Chop Check 41 Extrusion Pumps LITRES PER MINUTE DELIVERY

42 42 4-1/4" (43:1) SS Extrusion Pumps Ratio: 43:1 Bar: (Max.) Type: Chop Check P4X 5.8 mm mm 429 mm Recommended Accessories Air F/R/L: C Airline Oil: Air Motor Muffler: Wet Sol: B Follower Plate: A.S.A.P. Packages: Fluid Pressure (Bar) Performance 4-1/4", 43:1, Chop Check Air Inlet Pressure Range bar Fluid Pressure Range bar Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Litre Cycles / Minute l/min Noise 4 bar db(a) Specifications Lower Pump Material Stnls. Steel Plunger Material Stnls. Steel (Chrome Plated) Cylinder Material Stnls. Steel (Chrome Plated) Air Motor Motor Repair Kit Motor Diameter /4 Stroke mm Air Inlet /2 NPT(F) Exhaust Port /4 NPT(F) Pump Model: Model NM P P43 Model NM P P48 Lower Pump Repair Kits: Model NM2322F-11-P P43 Model NM2322F-11-P P48 Material Inlet Follower Plated Mounted Material Outlet /2 NPT(F) Weight kg Ordering P 4 X Packing 3 : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) CYCLES PER MINUTE bar Performance based on 30 wt. gear oil at ambient temperature LITRES PER MINUTE DELIVERY 8.3 bar Air Consumption (litres/sec.)

43 Fluid Pressure (Bar) Performance 8", 44:1, Chop Check Air Inlet Pressure Range bar Max. Fluid Pressure Range bar Max. Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Litre Cycles / Minute l/min Noise 4 bar db(a) w/muffler Lower Pump Material Carbon Steel Plunger Material Carbon Steel Cylinder Material Stnls. Steel (Chrome Plated) Air Motor Motor Repair Kit Motor Diameter Stroke mm Air Inlet /4 NPT(F) Exhaust Port NPT(F) Chop Check Pump Model X47-B Lower Pump Repair Kit X47-B Material Inlet Bolted Flange Material Outlet NPT(F) Weight kg Ordering CYCLES PER MINUTE bar Performance based on 90 wt. gear oil at ambient temperature bar Specifications X B Packings G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) LITRES PER MINUTE DELIVERY Air Consumption (litres/sec.) X47-B mm mm mm Recommended Accessories Air F/R/L: Airline Oil: Air Motor Muffler: Wet Sol: B Floor Mount: Rams: Page " (44:1) CS Ratio: 44:1 Bar: (Max.) Type: Chop Check Extrusion Pumps

44 44 6" (45:1) X4X 9 mm 481 mm 322 mm Performance 6", 45:1, 2-Ball Air Inlet Pressure Range bar Fluid Pressure Range bar Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Litre Cycles / Minute l/min Noise 4 bar db(a) Specifications Lower Pump Material CF8M (316) Stnls. Steel Plunger Material See Plunger Options Below Cylinder Material See Plunger Options Below Air Motor B Motor Repair Kit Motor Diameter Stroke mm Air Inlet /2 NPT(F) Two-Ball Pump Model X4X Lower Pump Repair Kit X43 Material Inlet NPT(F) 2 NPT(M) Material Outlet NPT(F) Weight kg Recommended Accessories Air F/R/L: C Airline Oil: Air Motor Muffler: Wet Sol: B Wall Mounts: 66 Floor/Follower Adapter: Ordering X 4 X Packings 3 : Teflon C : UHMW-PE G : UHMW-PE/Leather Staggered Plungers 3 : 17-4 S. S. Hard Chrome Plated B : 17-4 S.S. Ultra Coated COATING Piston Pumps Ratio: 45:1 Bar: (Max.) Type: 2-Ball Fluid Pressure (Bar) CYCLES PER MINUTE Performance based on 5 poise oil at ambient temperature 8.3 bar 8.3 bar LITRES PER MINUTE DELIVERY Air Consumption (litres/sec.)

45 Fluid Pressure (Bar) Performance 6", 46:1, Chop Check Air Inlet Pressure Range bar Fluid Pressure Range bar Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Litre Cycles / Minute l/min Noise 4 bar db(a) w/muffler Lower Pump Material Carbon Steel Plunger Material Stnls. Steel (Chrome Plated) Cylinder Material Carbon Steel (Nickel Plated) Air Motor B Motor Repair Kit Motor Diameter Stroke mm Air Inlet /2 NPT(F) Exhaust Port /4 NPT(F) Chop Check Pump Model X43-B Lower Pump Repair Kit X43-B Material Inlet Bolted Flange Material Outlet NPT(F) Weight kg Ordering CYCLES PER MINUTE bar Performance based on 90 wt. gear oil at ambient temperature Specifications X B Packings G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) LITRES PER MINUTE DELIVERY 8.3 bar Air Consumption (litres/sec.) X43-B mm mm mm Recommended Accessories Air F/R/L: C Airline Oil: Air Motor Muffler: Wet Sol: B Floor Mount: Rams: Page 15 Ratio: 46:1 Bar: (Max.) Type: Chop Check 45 6" (46:1) CS Extrusion Pumps

46 X4X Performance 6", 60:1, 2-Ball Air Inlet Pressure Range bar 6" (60:1) Fluid Pressure Range bar Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Cycles Per Litre Cycles / Minute l/min Noise 4 bar db(a) 9 mm Specifications Lower Pump Material CF8M (316) Stnls. Steel Plunger Material See Plunger Options Below Cylinder Material See Plunger Options Below Air Motor B Motor Repair Kit Motor Diameter Stroke mm 481 mm Air Inlet /2 NPT(F) Two-Ball Pump Model X4X 322 mm Lower Pump Repair Kit X43 Material Inlet NPT(F) 2 NPT(M) Material Outlet NPT(F) Weight kg Recommended Accessories Air F/R/L: C Airline Oil: Air Motor Muffler: Wet Sol: B Wall Mounts: 66 Floor/Follower Adapter: Ordering X 4 X Packings 3 : Teflon C : UHMW-PE G : UHMW-PE/Leather Staggered Plungers 3 : 17-4 S. S. Hard Chrome Plated B : 17-4 S.S. Ultra Coated COATING Piston Pumps Ratio: 60:1 Bar: 408 (Max.) Type: 2-Ball Fluid Pressure (Bar) CYCLES PER MINUTE Performance based on 5 poise oil at ambient temperature Air Consumption (litres/sec.) LITRES PER MINUTE DELIVERY

47 Fluid Pressure (Bar) Performance 4 in 2, 1.2:1, Chop Check Hydraulic Inlet Pressure Range bar Fluid Pressure Range bar Required 50 cpm bar Hydraulic flow req 50 cpm l/min Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Volume / Cycle ml Cycles Per Litre Cycles / Minute l/min Maximum Temperature Limit C Specifications Lower Pump Material Carbon Steel (Nickel Plated) Plunger Material Carbon Steel (Chrome Plated) Cylinder Material Carbon Steel (Nickel Plated) Hydraulic Motor Motor Repair Kit Motor Size cm 2 Stroke mm Hydraulic Inlet /2 NPT(F) Hydraulic Return /4 NPT(F) Chop Check Pump Model XX4-B Lower Pump Repair Kit XX4-B Material Inlet Bolted Flange Material Outlet /2 NPT(F) Weight ??.? Kg Ordering XX4-B Recommended Accessories X X 4 - B Floor Mount: Packings / Springs F : UHMW-PE/Leather Staggered (Upper), UHMW-PE (Lower) J : Polyurethane (Upper) UHMW-PE (Lower), P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE (Upper) Teflon (Lower) CYCLES PER MINUTE bar Performance based on 30 wt. gear oil at ambient temperature bar LITRES PER MINUTE DELIVERY Hydraulic Oil Consumption (litres/min.) 1344 mm 926 mm Wet Sol: B Rams: Page mm 47 HYD" (1.2:1) CS Hydraulic Extrusion Pumps Ratio: 1.2:1 Bar: (Max.) Type: Chop Check

48 48 HYD" (3.6:1) CS Hydraulic Extrusion Pumps Ratio: 3.6:1 Bar: (Max.) Type: Chop Check X43-C 1206 mm 841 mm 450 mm Recommended Accessories Floor Mount: Wet Sol: B Rams: Page 15 Fluid Pressure (Bar) Performance 2 in 2, 3.6:1, Chop Check Hydraulic Inlet Pressure Range bar Fluid Pressure Range bar Required 50 cpm bar Hydraulic flow req 50 cpm l/min Max. Rec d Cycles Per Minute Displacement Per Cycle cm 3 Volume / Cycle ml Cycles Per Litre Cycles / Minute l/min Maximum Temperature Limit C Lower Pump Material Carbon Steel Plunger Material Stns. Steel, (Chrome Plated) Cylinder Material Carbon Steel (Nickel Plated) Hydraulic Motor Motor Repair Kit Motor Size cm 2 Stroke mm Hydraulic Inlet /8 NPT(F) Hydraulic Return /2 NPT(F) Chop Check Pump Model X43-B Lower Pump Repair Kit X43-B Material Inlet Bolted Flange Material Outlet NPT(F) Weight Kg Ordering CYCLES PER MINUTE Performance based on 30 wt. gear oil at ambient temperature Specifications X C Packings 3 : Teflon C : UHMW-PE G : UHMW-PE/Leather Staggered P : UHMW-PE/Teflon Staggered (Upper), UHMW-PE (Lower) R : Teflon/UHMW-PE Staggered (Upper), Teflon (Lower) 82.8 bar 62.1 bar 41.4 bar 20.7 bar Hydraulic Oil Consumption (litres/min.) LITRES PER MINUTE DELIVERY

49 49 Personal Notes

50 50 Personal Notes

51 MANUAL OR AUTOMATIC EXTRUSIONS APPLICATION? JUST CALL US!

52 Ingersoll-Rand offers a full range of diaphragm pumps. For further information contact Ingersoll-Rand or your nearest distributor Ingersoll-Rand European Sales Limited 5-7 Avenue Albert Einstein, Zone Industrielle, Trappes, France Tel: +33 (0) Fax: +33 (0) The Ingersoll-Rand distributor network gives you not only a superior product, but also a Total Quality service, to ensure your complete satisfaction. For additional information about the products shown in this catalogue, and assistance with selection, please contact your nearest Ingersoll-Rand distributor or Ingersoll-Rand office. DISTRIBUTOR: Nothing contained within this brochure is intended to extend any warranty or representation, expressed or implied, regarding the products described herein. Any such warranties or other items or conditions of sale of products shall be in accordance with Ingersoll-Rand' s standard terms and conditions of sale for such products, which are available upon request. Product improvement is a continuing goal at Ingersoll-Rand. Designs and specifications are subject to change without notice or obligation. Form No. E74 CPN Printed in England 2000 by Ingersoll-Rand Company Printed on environmentally friendly Elemental Chlorine Free Paper