Section II. Parts Manual

Transcription

1 Section II Parts Manual

2 06-2 TABLE OF CONTENTS Clean Track 12 1 DESCRIPTION PAGE Back Panel Assembly Base System Brush System Decal System Handle System Recovery System Solution System Wiring Diagram Accessories WHEN ORDERING PARTS * Use the 8 digit numbers from the Ref. No. columns in this parts list. * Specify the model and serial number of the machine. * Use the space below to record the model and serial number for future reference. Model Serial No.

3 BACK PANEL ASSEMBLY 2 Clean Track

4 06-2 BACK PANEL ASSEMBLY Clean Track 12 3 Item Ref. No. Qty Description Switch, Rocker Cord, Power 16/3, SJT Barb, Hose Male Wsh, Flt SS.219 x.500 x.047/ Scr, Pan Phil SS x Nut, Hex Jam SS 5/ Socket, 1/8 FPT Strain Relief, Gasket, Back Panel Weldment, Back Panel Circuit Breaker W/Boot Wsh, Int Shprt # Nut, Hex Machine Nut, Conduit Lock 1/2-14

5 BASE SYSTEM 4 Clean Track

6 06-2 BASE SYSTEM Clean Track 12 5 Item Ref. No. Qty Description Bushing.31 x.50 x Adaptor, Barbed Pin, Spr.19 x Nut, Hex Nyl Loc SS Wsh, Flt SAE SS 5/ Nut, Hex Jam SS 5/ Scr, Hex SS 5/16-18 x Scr, Pan Phil Plastite 8-10 x Scr, Pan Phil SS x Scr, Pan Phil SS Plastite x Wsh, Flt SS.219 x.500 x.047/ Grommet Clamp, Hose SAE # Terminal Block Pump 115V Pump Rebuild Kit (for use in ) Rectifi er, 35 Amp Base Panel Valve, Nozzle Assembly (items 29-36) Base, Gasket, Base Panel Hose, 1/4 x 21.00L Hook, Base Clamp, Hose SAE # Hose Barb, Adapter 1/2 x 3/8NPT Muffl er Set Grommet Elbow, 90 Street Nipple, 1/4NPT x.88/ Hose, Solution Valve, Solenoid 115V Elbow, Panel Mount Nozzle Elbow, 90 Street Barb, 90 Elbow 1/4 x 1/4NPT Clamp, Hose SAE #4

7 DECAL BRUSH SYSTEM 6 Clean Track

8 06-2 BRUSH DECAL SYSTEM Clean Track 12 7 Item Ref. No. Qty Description Bearing/Spindle Kit NA 1 Spindle, Drive NA 1 Washer, Bearing NA 1 Bearing, Block NA 1 Sheave Poly-V 6J17 NA 1 Bearing, Ball NA 1 Bearing, Ball Bracket, Motor Tension Brush Assembly Motor, 115V, 1/4 HP Sheave, Poly-V Clip, Brush Retainer Nut, Hex Nyl Loc SS Scr, Pan Phil SS x Nut, Hex Nyl Loc-Thin Scr, Soc SS M6-1 x 20mm Nut, Hex Nyl Loc SS M Wsh, Flt SS.260 x x Scr, Soc Set Loc 5/16-18 x Belt, Poly V

9 DECAL SYSTEM 8 Clean Track

10 06-2 DECAL SYSTEM Clean Track 12 9 Item Ref. No. Qty Description Decal, Clarke Decal, Switch / Breaker Decal, Operation Instructions

11 HANDLE SYSTEM Clean Track

12 06-2 HANDLE SYSTEM 18 Clean Track Item Ref. No. Qty Description Scr, Pan Phil x Scr, Pan Phil Plastite 4-20 x Ratchet Button, Spray Switch, SPDT Snapaction Rod, Handle Cover, Handle Tube, Handle Wire Assy, 20AWG/2cond Knob Clamp, Handle

13 RECOVERY SYSTEM 12 Clean Track

14 06-2 RECOVERY SYSTEM Clean Track Item Ref. No. Qty Description Scr, Flt Phil 1/4-20 x Tank, Recovery Handle, Lid Lid Assembly (includes item 5) Gasket, Lid

15 SOLUTION SYSTEM 14 Clean Track

16 06-2 SOLUTION SYSTEM Clean Track Item Ref. No. Qty Description Wsh, Flt SAE SS 1/ Scr, Pan Phil 1/4-20 x Scr, Pan Phil SS x Scr, Pan Phil SS 1/4-20 x Scr, Pan Phil SS 1/4-20 x Scr, Pan Phil SS 1/4-20 x Scr, Pan Phil Plastite x Nut, Push Cap 1/ Wsh, Flt SS.219 x.500 x.047/ Wheel Clamp, Hose SAE # Hose Barb Ratchet Screen Tank, Solution Cover, Vac Assembly Axle Retainer, Axle Plate, Motor Shoe, Gasket Gasket Gasket Gasket, Vac Cover Gasket Vac Hose 1.50 Stretch Vacuum Motor 115V * Carbon Brushes (set of 2) for use on Bushing.25 x.37 x Barb, Adapter 1/2 x 3/8NPT Barb, 90 Elbow 1/2 x 3/8NPT Tie, Cable * = Not Shown

17 SOLUTION WIRING DIAGRAM SYSTEM 16 Clean Track POWER CORD G N L WHT WHT GRN #10 RING TERMINAL (FASTEN TO CONROL PANEL) 1 GRN GRN GRN/YEL (4 Cond Cable) S ROCKER SWITCH WHT #1 (4 Cond Cable) 1 1 M1 M 1~ 3 M3 M 3 1~ GRN #3 (4 Cond Cable) MOTOR, VACUUM AMP = MOTOR, PUMP AMP = 0.6 GRN GRN X1 1 2 N 3 4 N 5 6 N L1 2 SOLENOID VALVE AMP =.06 WHT 1 F1 CIRCUIT BREAKER, 3 A. 2 #2 (2 Cond Cable) 1 S1 2 3 HANDLE SWITCH #1 (2 Cond Cable) #2 (4 Cond Cable) D1 DIODE BRIDGE - ~ ~ + RED + MOTOR, BRUSH AMP = 2.3 M2 M GRN - E_GND

18 06-2 WIRING DIAGRAM Clean Track Item Ref. No. Qty Description D Rectifi er, 35 Amp F Circuit Breaker, W/Boot (3 Amp) L Valve, Solenoid 115V M Motor Vacuum, 115V * Carbon Brushes (set of 2) for use on M Motor, Brush 115 VDC, 1/4 HP M Motor, Pump 115V S Switch, Handle (Solution/Brush) S Switch, Rocker (Power) * Wire Assy, Rectifi er Blk * Wire Assy, Rectifi er Wht * Wire Assy, 20 AWG/2 Cond * Wire Assy, 16 AWG/4 Cond Power Cord * = Not Shown

19 ACCESSORIES 18 Clean Track AVAILABLE BRUSH Brush Assembly 12 ACCESSORY TOOLS Wand Assembly w/soft and Hard Floor Tools Wand Assembly w/soft Floor Tool Stand Up Wand Hand Tool Upholstery Hand Tool Hose w/waterline Hose w/waterline