DMS Series. Commercial Version MIL-C-5015 Compatible DMS FEATURE

Transcription

1 MS Series ommercial ersion MI ompatible MS MS series connectors are intermateable and intermountable with MI connectors. The MS series offers: ard dielectric interial (diallyl phthalate) Zinc plated die cast aluminum shells with olive drab chromate finish (no cadmium is used) selection of over 73 insert arrangements spanning 12 shell sizes and 5 contact sizes Pre-solder cup terminations choice of class (one-piece) and class (two-piece) backshell configuration MS series connector are designed for use in a wide range of general industrial applications. TUR Improved ielectric Withstanding oltage (W): n insulation barrier ridge between each contact position effectively arrier increases the creepage distance across the surfaces of the insert, thus increasing W. Stable Insert ilectric Material: Molded iallyl Phthalate inserts maintain their dielectric, mechannical, and dimensional properties over a wide range of temperature, humidity, and aging conditions. Wide Range onfigurations: choice of over 73 insert arrangements, plus a variety of shell styles and hardware, results in a range of configurations to meet most application needs. Shells eyed to Prevent Mis-Mating: Receptacle key and plug keyway mate before contacts engage to ensure proper contact mating. lternate rotated insert positions further ensure against mis-mating of similar connectors. Superior Strength of oupling Ring: oupling rings are machined from bar stock to provide superior coupling thread strength as compared to die cast products. Quick and asy Termination: ontacts are pre-loaded in the connector. Pre-solder cups are permanently oriented in one direction to simplify termination. OTR 1

2 MS Series MS PPITION The MS series is designed and manufactured for reliable performance in a broad range of electric/electronic equipment applications. These include machine tools, communications, instrumentation and high current systems. MTRI/INIS ontact Insulator Shell oupling Ring Retaining Ring ap hain opper alloy/silver or optional old plating iallyl phthalate resin/lue luminum alloy/zinc plating, Olive drab chromate finish luminum alloy/zinc plating, Olive drab chromate finish Phosphor bronze/zinc plating, Olive drab chromate finish luminum alloy/zinc plating, Olive drab chromate finish Stainless steel Wire Size ontact urrent Rating Service Rating ontact Size Wire Size #16 W#16-#22 #12 W#12-#14 #8 W#8-#10 #4 W#4-#6 #0 W#0-#2 ontact Size Test current (mperes) #16 13 #12 23 #8 46 #4 80 #0 150 Maximum total current connector is the same as the allowable current for wire bundles as specified in MI-W Service Rating Operating oltage () INST

3 MS Series Insert rrangements (ront iew of Pin Insert) MS 1 ontact 2 ontacts #0 Serv. 10S-4 2-#16 Serv. 12S-3 2-#16 Serv. 14S-9 2-#16 Serv #8 Serv #0 Serv. 3 ontacts 10S-3 3-#16 Serv. 14S-1 3-#16 Serv. 14S-7 3-#16 Serv. 16S-5 3-#16 Serv #12 Serv #12,1-#16 Serv #12 Serv #16 Serv #8 Serv #4 Serv #0 Serv. () () 4 ontacts 14S-2 4-#16 Serv. INST #16 Serv #12 Serv #12 Serv #16 Serv #8 Serv. ontact Sizes #8 Serv #4 Serv #0 Serv. #16 #12 #8 #4 #0 3

4 MS Series MS Insert rrangements (ront iew of Pin Insert) 5 ontacts 6 ontacts 14S-5 5-#16 Serv. INST 16S-8 5-#16 Serv #12 Serv #16 Serv. 14S-6 6-#16 Serv. INST #16 Serv #12, 1-#16 Serv #0,3-#12 Serv. () (Others) #4,2-#16 Serv #8, 3-#16 Serv #0, 3-#12 Serv. 7 ontacts 8 ontacts 9 ontacts 16S-1 7-#16 Serv #12 Serv #12 Serv #12, 7-#16 Serv. I #12, 7-#16 Serv #16 Serv. () () I #12, 6-#16 Serv #12 Serv #8 Serv #4, 2-#8, 3-#12 Serv. () (Others) #12 Serv. () (Others) I #8, 6-#12 Serv. 10 ontacts 11 ontacts 14 ontacts I I N M P N M M N P #16 Serv. () INST(Others) #12, 9-#16 Serv #16 Serv #16 Serv #12, 4-#16 Serv. ontact Sizes #16 Serv #4, 12-#16 Serv. I M N #16 #12 #8 #4 #0 4

5 MS Series Insert rrangements (ront iew of Pin Insert) 16 ontacts 17 ontacts 19 ontacts 20 ontacts 22 ontacts 24 ontacts 26 ontacts 30 ontacts 31 ontacts 35 ontacts 37 ontacts 48 ontacts 52 ontacts 54 ontacts 73 ontacts ontact Sizes #16 #12 #8 #4 #0 P S R M N #16 Serv. P O I M N #12,14-#16 Serv. P R S M N #16 Serv. T R S M N #16 Serv. T P U P R S M N #16 Serv. T Q U P R S M N #12,18-#16 T U Serv. W X I P R S M N #16 T Q U Serv. W X Y Z P R S M N #16 T Y W U Serv. X Z d b a P R S M N #12,24-#16 T Y U Serv. W X Z c d e a b I O #4,2-#8 Serv. P R S M N T Y U W X Z c d e a b O f I 14-#12,14-#16 P R S M N T U X Y Z W a c h j d f g e k m I #16 Serv. b P R S M N T Y U W X Z c d e a b I O h j f k g #12,28-#16 Serv.INST(hj) (others) P R S M N T U W X Z a e b f c d g m h j k s n p r #12 Serv. M U N P Q R T S O b W X Y a Z k e f g j h d n p q s r m c u v w x t y z #16 Serv. M N P T R S U Q W X Y Z c a b d e f k h j l m n s p r t u v y w x z 2 6 g #16 Serv. P R S M N T Y U W X Z O g s c n w t h z d p x i u e q y a k v f r b m #16 Serv. M U N P R T S W X Y Z b a f g j h d n p q s r m c u v w x t y z i k M N R S T U W X Y Z P #16 Serv. 5 MS

6 MS Series MS lternate Insert Positions Shell master key/keyway W X Y Z ront iew of Pin Insert No. of. ontacts Insert No. W X Y Z S S S S S S S S S S S No. of. ontacts Insert No. W X Y Z 16S

7 MS Series Insert Specfications MS Insert No. of Service ontact Size Number ontacts Rating #0 #4 #8 #12 #16 10S S S S S-2 4 INST 4 14S-5 5 INST 5 14S-6 6 INST 6 14S S S S S INST Insert No. of Service ontact Size Number ontacts Rating #0 #4 #8 #12 # INST INST Note : Insert number 10S-3 and 10S-4 are available with the following part numbers only: MS310210S-3P, MS310210S-4P MS310610S-3S, MS310610S-4S 7

8 MS Series MS MS SY(62) S STY 3100 : Wall Mounting Receptacle, Solid Shell 3101 : able onnecting Receptacle, Solid Shell 3102 : ox Mounting Receptacle 3106 : Straight Plug, Solid Shell 3106 : Straight Plug, Split Shell 3108 : ngle Plug, Split Shell ITION Omit : Silver plated contacts (62) : old plated contacts TRNT INSRT POSITION Omit : Standard position W.X.Y.Z : lternate position INSRT RRNMNT See page 3 to 5 ONTT STY P : Pin S : Socket Wall Mounting Receptacle, Solid Shell MS3100 M S R N R S φt Shell Size oupling Threads M N R S T Rear Threads 12S 3 / 4-20UN / 8-24UN 14S 7 / 8-20UN / 4-20UN 16S 1-20UN / 8-20UN UN / 8-20UN / 8-18UN UN / 4-18UN / 16-18UN / 8-18UN / 16-18UN / 2-18UN / 16-18UN / 4-18UNS / 16-18UN UNS / 4-18UNS / 4-16UN UNS 8

9 MS Series able onnecting Receptacle, Solid Shell MS3101 MS N Shell Size oupling Threads N Rear Threads 12S 3 / 4-20UN / 8-24UN 14S 7 / 8-20UN / 4-20UN 16S 1-20UN / 8-20UN UN / 8-20UN / 8-18UN UN / 4-18UN / 16-18UN / 8-18UN / 16-18UN / 2-18UN / 16-18UN / 4-18UNS / 16-18UN UNS / 4-18UNS / 4-16UN UNS 9

10 MS MS Series ox Mounting Receptacle MS min M S R N R S 12.7max φt Shell Size oupling Threads M N R S T 10S 5 / 8-24UN S 3 / 4-20UN S 7 / 8-20UN S 1-20UN UN / 8-18UN / 4-18UN / 8-18UN / 2-18UN / 4-18UNS UNS / 4-16UN

11 MS Series Straight Plug, Solid Shell MS3106 MS N Q Shell Size oupling Threads Q N Rear Threads 10S 5 / 8-24UN / 8-24UN 12S 3 / 4-20UN / 8-24UN 14S 7 / 8-20UN / 4-20UN 16S 1-20UN / 8-20UN UN / 8-20UN / 8-18UN UN / 4-18UN / 16-18UN / 8-18UN / 16-18UN / 2-18UN / 16-18UN / 4-18UNS / 16-18UN UNS / 4-18UNS / 4-16UN UNS 11

12 MS MS Series Straight Plug, Split Shell MS3106 N Q Shell Size oupling Threads Q N Rear Threads 12S 3 / 4-20UN / 8-24UN 14S 7 / 8-20UN / 4-20UN 16S 1-20UN / 8-20UN UN / 8-20UN / 8-18UN UN / 4-18UN / 16-18UN / 8-18UN / 16-18UN / 2-18UN / 16-18UN / 4-18UNS / 16-18UN UNS / 4-18UNS / 4-16UN UNS 12

13 MS Series ngle Plug, Split Shell MS3108 MS U R Q Shell Size 12S oupling Threads Q R U 3 / 4-20UN Rear Threads 5 / 8-24UN 14S 7 / 8-20UN / 4-20UN 16S 1-20UN / 8-20UN UN / 8-20UN / 8-18UN UN / 4-18UN / 16-18UN / 8-18UN / 16-18UN / 2-18UN / 16-18UN / 4-18UNS / 16-18UN UNS / 4-18UNS / 4-16UN UNS 13

14 MS MS Series ssembly MS3100 MS3101 MS3106 M MS3102 MS3106 N MS3108 N M : ack Shell : Split ack Shell : Retaining Ring : Pin Rear Insert : Pin ontact : Pin ront Insert : Socket Rear Insert : Socket ontact : Socket ront Insert : ront Shell : Shell M : oupling Ring N : Screws 14

15 MS (190) Series Moistureproof Plug Type Intermateable with 02-2 and MS Series MS (190) series is intermatable with 02-2, MS and MI connectors. These connectors meet the performance criteria of most factory automation applications as they withstand exposure to moisture, oil and vibration. MS(190) MTRI/INIS Shell Insulator ontact oupling Ring Retaining Ring asket luminum alloy/zinc plating, Olive drab chromate finish iallyl phthalate resin/lue opper alloy/silver plating luminum alloy/zinc plating, Olive drab chromate finish Phosphor bronze/zinc plating, Olive drab chromate finish Nitrile rubber/lack Specification ontact Size #16 #12 #8 oltage Rating 250 (rms) (rms) (rms) 500 urrent Rating 13 max 23 max 46 max Test oltage 1000 (rms) 1500 (rms) 1500 (rms) Insulation Resistance 1000MΩ min, at 500 Wire Size W#16~#22 SW#12~14 W#8~#10 1

16 MS (190) Series MS SW(190) MS(190) S STY 3106 : Staight Plug INSRT RRNMNT See page 3 to 5 ITION (190): onduit type TRNT INSRT POSITION Omit : Standard position W,X,Y,Z : lternate position ONTT STY S : Socket asket Shell Size oupling Threads Rear Threads 10S 5 / 8-24UN / 16-24UN S 3 / 4-20UN / 16-24UN S 7 / 8-20UN / 4-20UN S 1-20UN / 8-20UN UN / 8-20UN / 8-18UN UN / 4-18UN / 8-18UN / 8-18UN / 4-18UN / 2-18UN / 8-18UN / 4-18UNS / 8-18UN UNS / 8-16UN / 4-16UN / 8-16UN ontact Size #16 #12 #8 #4 #0 8max 8max 16max 13max 13max 2

17 MS (190) Series Insert rrangements (ront iew of Pin Insert) 1 ontact 2 ontacts MS(190) #0 Serv. 10S-4 2-#16 Serv. 12S-3 2-#16 Serv. 14S-9 2-#16 Serv #8 Serv #0 Serv. 3 ontacts 10S-3 3-#16 Serv. 14S-1 3-#16 Serv. 14S-7 3-#16 Serv. 16S-5 3-#16 Serv #12 Serv #12,1-#16 Serv #12 Serv #16 Serv #8 Serv #4 Serv #0 Serv. () () 4 ontacts 14S-2 4-#16 Serv. INST #16 Serv #12 Serv #12 Serv #16 Serv #8 Serv. ontact Sizes #8 Serv #4 Serv #0 Serv. #16 #12 #8 #4 #0 3

18 MS (190) Series Insert rrangements (ront iew of Pin Insert) MS(190) 14S-5 5-#16 Serv. INST 16S-8 5-#16 Serv. 5 ontacts 6 ontacts #12 Serv #16 Serv. 14S-6 6-#16 Serv. INST #16 Serv #12, 1-#16 Serv #0,3-#12 Serv. () (Others) #4,2-#16 Serv #8, 3-#16 Serv #0, 3-#12 Serv. 7 ontacts 8 ontacts 9 ontacts 16S-1 7-#16 Serv #12 Serv #12 Serv #12, 7-#16 Serv. I #12, 7-#16 Serv #16 Serv. () () I #12, 6-#16 Serv #12 Serv #8 Serv #4, 2-#8, 3-#12 Serv. () (Others) #12 Serv. () (Others) I #8, 6-#12 Serv. 10 ontacts 11 ontacts 14 ontacts I I N M P N M M N P #16 Serv. () INST(Others) #12, 9-#16 Serv #16 Serv #16 Serv #12, 4-#16 Serv. ontact Sizes #16 Serv #4, 12-#16 Serv. I M N #16 #12 #8 #4 #0 4

19 MS (190) Series Insert rrangements (ront iew of Pin Insert) 16 ontacts 17 ontacts 19 ontacts 20 ontacts 22 ontacts 24 ontacts 26 ontacts 30 ontacts 31 ontacts 35 ontacts 37 ontacts 48 ontacts 52 ontacts 54 ontacts 73 ontacts ontact Sizes #16 #12 #8 #4 #0 P S R M N #16 Serv. P O I M N #12,14-#16 Serv. P R S M N #16 Serv. T R S M N #16 Serv. T P U P R S M N #16 Serv. T Q U P R S M N #12,18-#16 T U Serv. W X I P R S M N #16 T Q U Serv. W X Y Z P R S M N #16 T Y W U Serv. X Z d b a P R S M N #12,24-#16 T Y U Serv. W X Z c d e a b I O #4,2-#8 Serv. P R S M N T Y U W X Z c d e a b O f I 14-#12,14-#16 P R S M N T U X Y Z W a c h j d f g e k m I #16 Serv. b P R S M N T Y U W X Z c d e a b I O h j f k g #12,28-#16 Serv.INST(hj) (others) P R S M N T U W X Z a e b f c d g m h j k s n p r #12 Serv. M U N P Q R T S O b W X Y a Z k e f g j h d n p q s r m c u v w x t y z #16 Serv. M N P T R S U Q W X Y Z c a b d e f k h j l m n s p r t u v y w x z 2 6 g #16 Serv. P R S M N T Y U W X Z O g s c n w t h z d p x i u e q y a k v f r b m #16 Serv. M U N P R T S W X Y Z b a f g j h d n p q s r m c u v w x t y z i k M N R S T U W X Y Z P #16 Serv. 5 MS(190)

20 MS (190) Series lternate Insert Positions MS(190) Shell master key/keyway W X Y Z ront iew of Pin Insert No. of. ontacts Insert No. W X Y Z S S S S S S S S S S S No. of. ontacts Insert No. W X Y Z 16S

21 MS (190) Series ngle ack Shell - -S (247) MS(190) TYP S: waterproof type No designation: Not waterproof type OOR No designation: Olive drab (247): lue Material/inish luminum alloy/hromate finish - -S ( ) is a waterproof backshell to hold a length of cable at right angle when no coduit is used. When connected with a cable clamp ( ), it provides water-proofing, oil resistant and dustproofing properties. 1 max. 2 max. U R O ring φ W P/N Shell Size 1 2 R U Threads Threads W -18-S UN 1-20UN -20-S / 8-18UN 1 3 / 16-18UN -22-S / 4-18UN 1 3 / 16-18UN -24-S / 8-18UN 1 7 / 16-18UN 7

22 MS (190) Series Waterproof able lamps MS(190) Material/inish luminum alloy/zinc plating, Olive drab chromate finish is a waterproof cable clamp for use with a plug in either the MS (190) series or the 01 or 02 series. The cable clamp body used the MS3057- that has a wateproof rubber bushing; therefore, be sure to use a jacketed cable meeting on of the applicable cable size ranges as shown. The cable clamp should be used together with a waterproof backshell. φ ushing P/N Shell Size Threads ushing P/N able Outer iameter 10..5~ UN ~ ~ ~ , / 16-18UN ~ ~ , ~19.1 / 16-18UN ~15.5 8

23 MS (190) Series ushing Material/inish Synthetic rubber (lack) MS(190) is the bushing used on cable clamp part number φ φ φ P/N pplicable Washer MS W MS W MS W 9

24 MS/MS //R Series MI ompatible nvironment Resistant Type MS/MS //R 's MS/MS series provides a set of moisture-resistant and oil-resistant connectors. This series uses synthetic rubber for their inserts to cope with the various environments in which industrial machines are installed. The products in the MS/MS series are compatible and comply with MI The and R types prevent the entry of water moisture, cutting oil and other foreign substances into machines where those connectors are employed, helping enhance the reliability of the equipment. TUR Synthetic rubber inserts rommet for moisture-proof Unified backshell with cable clamp rommet and cable clamp combination for extra strength to hold cable Solder termination contacts MTRI/INIS ontact Insulator Shell opper alloy / Silver plating thylene propylene rubber luminum alloy / Zinc plating, lack chromate finish luminum alloy / Olive drab cadmium finish 1

25 MS/MS //R Series SPIITION Wire size ontact size W #16 #16-# #12 #12-# #8 #8-# #4 #4-# #0 #0-# MS/MS //R ontact size ontact size Max. value per contact #16 13 #12 23 #8 46 #4 80 #0 150 Service rating Service rating Operating voltage (rms) INST Maximum total current connectors is same as the allowable current for wire bundles as specified in MI-W Service rating Insulation resistance 5,000M ohm min.(at 25 degree) Temperature range -55 degree to 125 degree Thermal shock MI-ST-202 Method 107 Temperature range of -55 degree to 125 degree umidity Relative humidity: 95% +/-3% Temperature: 71 degree +/-2 degree uration: 14 days (336hrs.) MI-ST-1344 Method 2005 ibration z or 10 units Shock, lectrical 1-2 sine wave transient shock Impulse of 50 units uration: 11 +/-1 micro sec. Test current: 100m Salt spray MI-ST-1344 Method 1001 Salt solution: 5% uration: 48 hours urability 500 cycle mating/ unmating operatings 2

26 MS/MS //R Series Insert rrangements-ront iew of Pin Insert 2 ontacts 3 ontacts MS/MS //R 10S-4 2-#16 Serv. 12S-3 2-#12 Serv #12 Serv. 10S-3 3-#16 Serv. 14S-7 3-#16 Serv. 16S-5 3-#16 Serv. 3 ontacts 4 ontacts #12 Serv. 14S-2 4-#16 Serv. INST #16 2-#12 Serv #12 Serv #8 Serv. 4 ontacts 5 ontacts 6 ontacts #4 Serv. 14S-5 5-#16 Serv. INST 16S-8 5-#16 Serv #12 Serv. 14S-6 6-#16 Serv. INST 6 ontacts 7 ontacts #0 3-#12 Serv. 16S-1 7-#16 Serv #12 Serv #8 Serv. ontact Sizes #16 #12 #8 #4 #0 3

27 MS/MS //R Series Insert rrangements-ront iew of Pin Insert 10 ontacts 11 ontacts 14 ontacts I #16 Serv. (,,,) Serv. INST(Others) #16 Serv. M #16 Serv. I N M #16 Serv. MS/MS //R 14 ontacts 17 ontacts 19 ontacts 24 ontacts P N M M T S N P R M U T S N P R M N P Q R S T U W X Y Z #16 Serv #16 Serv #16 Serv #16 Serv. INST 37 ontacts 45 ontacts M N P R S T U W X Z a b c d e f g h j k m n p r s #16 Serv. M N O P Q R S T U W X Y Z a b c d e f g h j k m n p q r s t u v w x y z #16 Serv. ontact Sizes #16 #12 #8 #4 #0 4

28 MS/MS //R Series lternate Insert Positions MS/MS //R Insert No. lternate ey Positions W X Y Z 10S S S S S S S S S S W Z X Y ront iew of Pin Insert 5

29 MS/MS //R Series Insert Specifications Insert No. No. of ontact Sizes Pins #0 #4 #8 #12 #16 10S 10S S S 12S S 14S S S S S 16S S S MS/MS //R 6

30 MS/MS //R Series MS SW MS/MS //R S STY 3100 : Wall Receptacle 3101 : able Receptacle 3102/R : ox Receptacle 3106/ : Straight Plug 3106R : Straight Plug 3108/ : ugle Plug TRNT INSRT POSITION Omit: Standard ey Position W,X,Y or Z : lternate ey Position ONTT STY P:Pin contact S:Socket ontact S SIZ/ INSRT RRNMNT See page 7 Receptacle onnector MS 3100 MS 3100 Plug onnector MS 3106/ MS 3106/ MS 3101 MS 3101 MS 3106R MS 3106R MS 3102/R MS 3102/R MS 3108/ MS 3108/ 7

31 MS/MS //R Series MS PW-()-()-() MS-hromate inish MS-hromate inish/rimp *1 (rimp contacts ordered seperately) MS-Olive rab admium inish MS-Olive rab admium inish/rimp *1 (rimp contacts ordered seperately) S STY 3100/ : Wall Mount Receptacle 3101/ : able Receptacle 3102//R : ox Mount Receptacle 3106///R : Straight Plug 3108// : Right ugle Plug Shell Size/Insert rrangement ONTT STY P:Pin ontacts S:Socket ontacts Note *1 : onsult ITION (313)-ess ack Shell & ccessories Omit:Silver Plated Solderontacts ""old Plated Solder ontacts old Plated rimp ontacts Ordered Seperately (129)-P ontacts [3102, Only] Omit-lack hromate inish (MS,MS, Only) ""-Olive rad hromate inish (MS,MS, Only) (240)-Nickel inish [onsult ] TRNT INSRT ROTTION Omit:Standard ey Pusition W, X, Y, Z: lternate ey Rotation MS/MS //R Straight Plug MS3106 (ess asket) MS3106 (ess asket) MS3106 (With asket) MS3106 (With asket) φmax. max. Shell Size φ 10S 5/8-24UN S 3/4-20UN S 7/8-20UN S 1-20UN UN /8-18UN /4-18UN /8-18UN /2-18UN /4-18UNS UNS /4-16UN

32 MS/MS //R Series Straight Plug MS3106R MS3106R MS/MS //R φmax. max. Shell Size φ 10S 5/8-24UN S 3/4-20UN S 7/8-20UN S 1-20UN UN /8-18UN /4-18UN /8-18UN /2-18UN /4-18UNS UNS /4-16UN ngle Plug MS3108 (ess asket) MS3108 (ess asket) MS3108 (With asket) φmax. MS3108 (With asket) Umax. max. Shell Size φ U 10S 5/8-24UN S 3/4-20UN S 7/8-20UN S 1-20UN UN /8-18UN /4-18UN /8-18UN /2-18UN /4-18UNS UNS /4-16UN

33 MS/MS //R Series Wall Mounting Receptacle MS3100 MS3100 Shell Size ±0.05 M R ±0.12 S ±0.5 φ S 5/8-24UN S 3/4-20UN S 7/8-20UN S 1-20UN UN /8-18UN /4-18UN /8-18UN /2-18UN /4-18UNS UNS /4-16UN MS/MS //R ole R min. M S max. 10

34 MS/MS //R Series able onnecting Receptacle MS/MS //R MS3101 MS3101 Shell Size φ ±0.5 S ±0.5 10S 5/8-24UN S 3/4-20UN S 7/8-20UN S 1-20UN UN /8-18UN /4-18UN /8-18UN /2-18UN /4-18UNS UNS /4-16UN φ min. S max. 11

35 MS/MS //R Series ox Mounting Receptacle MS3102 (ess asket) MS3102 (ess asket) MS3102R (With asket) MS3102R (With asket) MS/MS //R Shell Size ±0.5 M ±0.78 N ±0.5 R ±0.12 S ±0.5 φ ± S 5/8-24UN S 3/4-20UN S 7/8-20UN S 1-20UN UN /8-18UN /4-18UN /8-18UN /2-18UN /4-18UNS UNS /4-16UN ole φn R S min. M max

36 MS/MS //R Series ack Shells (Short) MS/MS //R MS- SS Plating: Olive rab admium P/N Thread Thread φ φ MS-10SSS 5/8-24 UN-2 9/16-24 UN MS-12SSS 5/8-24 UN-2 5/8-24 UN MS-14SSS 3/4-24 UN-2 3/4-24 UN MS-16SS 7/8-20 UN-2 7/8-20 UN MS-18SS 1-20 UN UN MS-20SS 1 3/16-18 UN-2 1 1/8-18 UN MS-22SS 1 3/16-18 UN-2 1 1/4-18 UN MS-24SS 1 7/16-18 UN-2 1 3/8-18 UN MS-28SS 1 7/16-18 UN-2 1 5/8-18 UN MS-32SS 1 3/4-18 UNS-2 1 7/8-16 UN MS-36SS 2-1/8 UNS-2 2 1/8-16 UN MS- SS- PTIN No designation : lack hromate over Zinc : Olive rab hromate over Zinc P/N Thread Thread φ φ MS-10SSS- 5/8-24 UN-2 9/16-24 UN MS-12SSS- 5/8-24 UN-2 5/8-24 UN MS-14SSS- 3/4-24 UN-2 3/4-24 UN MS-16SS- 7/8-20 UN-2 7/8-20 UN MS-18SS UN UN MS-20SS- 1 3/16-18 UN-2 1 1/8-18 UN MS-22SS- 1 3/16-18 UN-2 1 1/4-18 UN MS-24SS- 1 7/16-18 UN-2 1 3/8-18 UN MS-28SS- 1 7/16-18 UN-2 1 5/8-18 UN MS-32SS- 1 3/4-18 UNS-2 1 7/8-16 UN MS-36SS- 2-1/8 UNS-2 2 1/8-16 UN Thead Thead φ φ 13

37 MS/MS //R Series ack Shells (ong) MS- SS Plating: Olive rab admium P/N Thread Thread φ φ MS-10SSS 5/8-24 UN-2 9/16-24 UN MS-12SSS 5/8-24 UN-2 5/8-24 UN MS-14SSS 3/4-24 UN-2 3/4-24 UN MS-16SS 7/8-20 UN-2 7/8-20 UN MS-18SS 1-20 UN UN MS-20SS 1 3/16-18 UN-2 1 1/8-18 UN MS-22SS 1 3/16-18 UN-2 1 1/4-18 UN MS-24SS 1 7/16-18 UN-2 1 3/8-18 UN MS-28SS 1 7/16-18 UN-2 1 5/8-18 UN MS-32SS 1 3/4-18 UNS-2 1 7/8-16 UN MS-36SS 2-1/8 UNS-2 2 1/8-16 UN MS/MS //R MS- SS- PTIN No designation : lack hromate over Zinc : Olive rab hromate over Zinc P/N Thread Thread φ φ MS-10SSS- 5/8-24 UN-2 9/16-24 UN MS-12SSS- 5/8-24 UN-2 5/8-24 UN MS-14SSS- 3/4-24 UN-2 3/4-24 UN MS-16SS- 7/8-20 UN-2 7/8-20 UN MS-18SS UN UN MS-20SS- 1 3/16-18 UN-2 1 1/8-18 UN MS-22SS- 1 3/16-18 UN-2 1 1/4-18 UN MS-24SS- 1 7/16-18 UN-2 1 3/8-18 UN MS-28SS- 1 7/16-18 UN-2 1 5/8-18 UN MS-32SS- 1 3/4-18 UNS-2 1 7/8-16 UN MS-36SS- 2-1/8 UNS-2 2 1/8-16 UN Thead Thead φ φ 14

38 MS/MS //R Series ront Mounting askets MS- R MS/MS //R P/N Shell Size φ φ MS-10SR 10S MS-12SR 12S MS-14SR 14S MS-16R 16S, MS-18R MS-20R MS-22R MS-24R MS-28R MS-32R MS-36R imensions are for reference, only. φ 4-φ 1.5 Rear Mounting askets MS- P/N Shell Size φ φ MS-10S 10S MS-12S 12S MS-14S 14S MS-16 16S, MS MS MS MS MS MS MS imensions are for reference, only. 4-φ

39 MS ccessories MS Series of able lamps and ack Shells able lamp (with Rubber ushing) MS3057- Plating: Olive rab admium MS P/N Shell Size Thread ushing Par Number MS S, 12S /8-24 UN N MS S /4-20 UN N MS S, /8-20 UN N MS UN N MS , /16-18 UN N MS , /16-18 UN N MS /4-18 UNS N MS UNS N MS3057- PTIN No designation : Olive rab hromate over Zinc (235) : lack hromate over Zinc P/N Shell Size Thread ushing Par Number MS S, 12S /8-24 UN N MS S /4-20 UN N MS S, /8-20 UN N MS UN N MS , /16-18 UN N MS , /16-18 UN N MS /4-18 UNS N MS UNS N

40 MS ccessories able lamp (ess Rubber ushing) MS3057- Plating: Olive rab admium MS P/N Shell Size Thread MS S, 12S /8-24 UN MS S /4-20 UN MS S, /8-20 UN MS UN MS , /16-18 UN MS , /16-18 UN MS /4-18 UNS MS UNS MS3057- PTIN No designation : Olive rab hromate over Zinc (235) : lack hromate over Zinc P/N Shell Size Thread MS S, 12S /8-24 UN MS S /4-20 UN MS S, /8-20 UN MS UN MS , /16-18 UN MS , /16-18 UN MS /4-18 UNS MS UNS

41 MS ccessories Rubber ushings N3420- P/N N N N N N N N N MS nvironmental ushings P/N φ φ φ φ φ pplicable able ia. (Reference, Only) φ φ φ 3

42 MS ccessories dapters MS Plating: Olive rab admium MS P/N Thread Thread MS UN - 2 7/8-20 UN MS UN - 2 7/8-20 UN MS /16-18 UN - 2 7/8-20 UN MS /16-18 UN - 2 7/8-20 UN MS /16-18 UN /16-18 UN MS /16-18 UN /16-18 UN MS PTIN No designation : Olive rab hromate over Zinc (235) : lack hromate over Zinc P/N Thread Thread MS UN - 2 7/8-20 UN MS UN - 2 7/8-20 UN MS /16-18 UN - 2 7/8-20 UN MS /16-18 UN - 2 7/8-20 UN MS /16-18 UN /16-18 UN MS /16-18 UN /16-18 UN Thead Thead φ 4

43 MS ccessories P and hain ssembly MS MS P/N MS MS Shell Size 10S 12S Threads 5 / 8-24UN / 4-20UN MS S 7 / 8-20UN MS S, UN MS / 8-18UN MS / 4-18UN MS / 8-18UN MS / 2-18UN MS / 4-18UNS MS UNS MS / 4-16UN

44 MS ccessories MS MS P/N Shell Size Threads MS S 5 / 8-24UN MS S 3 / 4-20UN MS S 7 / 8-20UN MS S, UN MS / 8-18UN MS / 4-18UN MS / 8-18UN MS / 2-18UN MS / 4-18UNS MS UNS MS / 4-16UN

45 01 Series onforming to IS rimp ontact esign The 01 series connectors conform to IS These connectors meet the performance criteria of most factory automation applications as they withstand against exposure, oil and vibration. 01 TUR ayonet lock coupling Moistureproof type design With first-make, last-break contact grounded to shell for circuit protection OMPTI STNR IS SPIITION ontact size #20 #16 #12 #8 urrent rating INST oltage rating 200 (rms) 500 (rms) 900 (rms) ,250 ielectric withstanding voltage Insulation resistance 1,000 (rms) 1-MINUT 2,000 (rms) 1-MINUT 5,000MΩ min. at 500 2,800 (rms) 1-MINUT ontact resistance 8mΩ max 4mΩ max 2mΩ max 0.6mΩ max Operating temperature -55 to+125 umidity 85%max MTRI/INIS Shell oupling ring Insulator ontact round clip O-ring asket luminum alloy/lue chromate or olive drab chromate finish luminum alloy/lue chromate or olive drab chromate finish Polyester resin (U94-0)/ray opper alloy/silver plating opper alloy/silver plating Nitrile rubber Synthetic rubber 1

46 01 Series 01 Insert rrangements-ront iew of Pin Insert No. of ontacts rrangements Insert No ontact Sizes #8 #12 #12 #8 #12 Rating (4) (Others) No. of ontacts rrangements Insert No ontact Sizes #16 #16 #20 #16 #16 Rating (3,5,6,8) INST(Others) INST INST No. of ontacts rrangements Insert No ontact Sizes #20 #16 #20 #20 Rating INST INST INST Note : onnector mating side (Srandard insert position) 2

47 01 Series lternate Insert Positions 01 No. of. ontacts Insert No. W X Y Z W X Z Y Z Y W X ront view of pin insert ront view of socket insert Ordering Information or ontacts ontact Size #20 Quantity 100pcs/bag 10,000pcs/reel 01-#20P ontact P/N Wire Size Range Pin Socket W mm 2 Ins. ia. 01-#20S #26-# # #20P #20S #22-# max. 01-#20P #20S #26-# # #20P #20S #22-# max. 01-#16P #16S #24-# pcs/bag 01-#16P #16S #20-# #16 01-#16P #16S # #16P #16S #24-# max. 3,500pcs/reel 01-#16P #16S #20-# #16P #16S # #12 10pcs/bag 01-#12P-1M #12S-1M-10 #16-# max. #8 10pcs/bag 01-#08P-2M #08S-2M-10 #12-# #08P-1M #08S-1M-10 #10-# max. 3

48 01 Series PW-0S S STY 2: ox Mounting Receptacle 6: Straight Plug N ST Omit: ess asket S: With asket or 01-2 Only INSRT RRMMNT See page 2 SS ONTT ontacts are not included. ONTT STY P: Pin S: Socket S OOR Omit: lue (standard) : Olive rab color RIMP ONTT TRNT INSRT POSITION Omit: Standard position W,X,Y,Z: lternate position Pin contact Retaining ring Receptacle Socket insert Plug over insert(note) Pin insert oupling ring Shell Socket contact round clip Shell O-ring round clip Retaining ring Note: over insert is available for socket insert with #16 or #20 contacts only. 4

49 01 Series oxs Mounting Receptacle S±0.5 R ± 0.13 Master eyway +0 φ -0.5 asket 1.6 φ Pre-mating contact position Shell Size No. of. ont acts O P/N S R ontact Sizes Pin Insert max Socket Insert # O # O # O # O # O # O # O # O # O # O # O # O # O #

50 01 Series 01 Straight Plug Master eyway φ ± 0.2 φ ± 0.8 Threads 11max Pre-mating contact position Shell Size No. of. ont acts O P/N ontact Sizes Pin Insert max Socket Insert # O UN-2 # O # O # O /8-18UN-2 # O # O # O /4-18UN-2 # O # O # O /8-18UN-2 # O # O # /8-18UN O #

51 01 Series able lamps (Nonwaterproof Type) MS3057- (247) 01 Material/inish luminum alloy/zinc plating, lue chromate finish MS3057- is an accessory for use with a backshell to clamp a length of cable. The cable can be positioned exactly in the center of the cable clamp, because its structure is such that any cable can be fastened from both sides by two pressure bars. This cable clamp, which uses one of the synthetic rubber bushings shown in the specification list, can also be used for jacketed cable or bundled cable. If the cable to be used is much smaller in diameter than the bushing, a smaller bushing should be added. φ ushing φ Part Number Shell Size Threads ushing P/N MS (247) UN N MS (247) 20, / 16-18UN N MS (247) 24, / 16-18UN N Receptacle Rubber aps Material Synthetic rubber (lack) Shell Size P/N 18 01R-18R R-20R R-22R φ φ φ R-24R R-28R

52 01 Series 01 ssembly Tools ontact Size Wire Size Range and rimp Tools W mm 2 rimping Tool ocator Stopper Removal Tool #20 2 #26-# #22-# #24-# # #20-# # #12 1 #16-# #8 2 #12-# Note ( ) ( ) 1 #10-# ( ) Note: is a TOO IT part number which includes a crimp tool, , , and (Test gauge). The crimping tool can not be sold alone separately. 8

53 02-6 Series Moistureproof Plug Type onforming to MI and IS The 02 series circular connectors are designed to protect connections to electrical equipment from moisture, oil and surges in current which may damage electronic circuitry. The 02 series is intermateable with MI style connectors such as the MS series available from TUR irst-make, last-break contact to prevent damage to electronic circuitry. Intermateable with MI style connectors commonly used on existing factory automation and other electrical equipment. esigned to offer protection against moisture and oil. gasket located between the coupling ring and receptacle shell seals the connection. vailable water resistant backshells and cable clamps complete the sealed connection. Plug connector is also designed to accept conduit fittings. When used in this method and mated to 's 02-2 series connectors, the entire connection system from the cable to the inside of the equipment is sealed from moisture, oil, and dust. SPIITION urrent rating ontact size #16 #12 #8 Max.value per contact Service rating oltage rating (rms) Withstanding voltage (rms) Insulation resistance More than 5000MΩ at 500 ontact size #16 #12 #8 ontact resistance less than mω Test current Operating temperature -55 to +125 MTRI/INIS WIR SIZ Shell oupling ring Insert ontact Retaining ring round lug asket luminum alloy/zinc plating,olive drab chromate finish luminum alloy/zinc plating, Olive drab chromate finish iallyl phthalate/lue opper alloy/silver plating opper alloy/zinc plating, Olive drab chromate finish opper alloy/silver plating Nitrile butadiene rubber/lack ontact Size Wire Size #16 W#16-#22 #12 W#12-#14 #8 W#8-#10 1

54 02-6 Series Insert rrangements 02-6 Insert No. 10S rrangements M N T P S R ontact Sizes #16 #12 #16 #12 #16 No. of ontacts rounding ontact Position Service Rating urrent apacity Terminal Terminal Terminal Terminal NTerminal 13 (29.2) 23 (62.5) 13 (43.6) 23 (83.7) 13 (81.7) Insert No () () ontactrran gements T M U N S R P ontact Sizes #16 #8 #12 #8 #8 No. of ontacts rounding ontact Position Service Rating urrent apacity NTerminal Terminal Terminal Terminal Terminal (Terminal) (Others) 13 (88.9) 46 (125.1) 23 (90.1) 46 (167.4) 46 (167.4) lternate Insert Positions Insert No. ontact Sizes/ Number Non-standard key positionsθ W X Y Z 10S-3 #16/ #12/ #16/ #12/ #16/ #16/ # 8/ #12/ # 8/ Z W Y X ront iew of Socket Insert 2

55 02-6 Series S STY 6 : Straight Plug SW TRNT INSRT POSITION Omit : Standard position W,X,Y,Z : lternate position 02-6 S SIZ 10S, 18, 20, 22, 24 ONTT STY S : Socket INSRT RRNMNT See page 3 PRMTIN ONTT POSITION Refer to insert arrangements asket φ φ max P/N S-3S 5/8-24UN /16-24UN S /8-18UN UN S S /4-18UN /8-18UN NS NS S 1 3/8-18UN /4-18UN S S /2-18UN /8-18UN S

56 02-2 Series Moistureproof Receptacle Type onforming to MI 's 02-2 series provides a set of vibration-resistant, moistureproof, and oilproof receptacle connectors. This series uses synthetic rubber for its front inserts to cope with the various environments in which industrial machines are installed. The products in the 02-2 series are compatible with those in the MS series and comply to MI They prevent the entry of water moisture, cutting oil, and other foreign matter into machines where these connectors are employed, helping enhance the reliability of the machines. Typically, their best applications are in servo motors, machine tools, and equipment relating to factory automation as well as in extremely dusty environments. or plug connectors to mate with these receptacle connectors, recommends that you use the 02-6 series or the MS (190) series available from. TUR The products in the 02-2 series are interchangeable with those in the MS series, because both are indentical in installation dimensions. The inserts are of a three-piece design. Their contacts will not break when used under normal operating conditions. The inserts, which are made of silicone rubber, may be used at temperature of up to 125 oupling a receptacle connector in the 02-2 series with a plug connector in the 02-6 series or the MS (190) series allows the entire joint between the two connectors to be moistureproof. SPIITION Shell ront insert Middle insert Rear insert ontact lange gasket luminum alloy/zinc plating, Olive drab chromate finish Silicone rubber PPS resin PPS resin opper alloy/silver plating Silicone rubber MTRI/INIS WIR SIZ urrent rating ontact size #16 #12 #8 Max.value/Per contact oltage rating (rms) ielectric withstanding voltage (rms), 1minute 1,000 1,500 1,500 ontact resistance less than mω 5mΩ max. Operating temperature -40 to +125 ontact Size W #16 #16-#22 #12 #12-#14 #8 #8-#10 1

57 02-2 Series Insert rrangements The inserts in the 02-2 series are indentical to those in the MS series. Only the pin inserts are shown below. Insert No rrangements #12-4 #16-6 #12-7 M N T P S R # Insert No rrangements M U N T S R P #16-19 #8-4 #12-8 #8-7 Note : ach of the inserts in the 02 series is viewed from its coupling side. ll keys are set at their standard positions. lternate Insert Positions Non-standard key positionsθ Insert No. ontact Size/ No of W X Y Z ontact 18-10P #12/ P #16/ P #12/ P #16/ P #16/ P #8/ P #12/ P #8/ ront iew of Pin Insert (for Model P ) θ = 120 When more than one connector (of the same model ) is used in a single device, the key positions should be changed as shown in order to prevent the wrong connectors from being coupled together. 2

58 02-2 Series PWS 02-2 S STY 2 : Receptacle S SIZ 18, 20, 22, 24 INSRT RRNMNT See page 3 N ST Omit : ess asket S : With asket TRNT INSRT POSITION Omit : Standard position. W,X,Y,Z : ltenate position. ONTT STY P : Pin max φ 0.15 φ min () max ±0.5 min ± P/N () P 1 1/8-18UN P 1 1/8-18UN P 1 1/4-18UN P 1 1/4-18UN P 1 3/8-18UN P 1 3/8-18UN P 1 3/8-18UN P 1 1/2-18UN

59 05 Series onnectors onforming to uropean Safety Standards s of anuary 1995 all industrial machinery, including machine tools, which are exported to urope must conform with uropean safety standards. The 05 series connectors, which offer full compatibiliy with MS connectors in factory automation applications, were developed to comply with this demand. 05 TUR TU Rheinland onformity with uropean Safety Standards 05 series connectors fully conform with the following uropean safety standards : N (electric machinery parts) and IN 0627 (connectors). They have been approved by TU Rheinland. Sequence Structure with Protective ircuitry (irst-make, ast-break contact design) onnectors are provided with a premating and grounding contact, consisting of a shell having conductivity with the shell to serve as protective circuitry. When making connections, the contact of the 05 connector is connected first before other contacts, and detached last. onformity with MI connectors fully comply with MI standards and can be mated with conventional MS connectors. Water/Oil/ustproof Structure : lass IP67 Protection Once connected, full protection is provided against ingression of water droplets, cutting fluid, dust particles, etc. Use of a synthetic rubber insert ensures protection against water and dust even in the unconnected state in the case of the receptacle with male contacts. Plug onnector ccessories vailable accessories include waterproof straight-backshells, waterproof angle-backshells and waterproof cable clamps (with rubber bushing). Plug connectors are also available for conduit applications. Solder Wire ike MS connectors, 05 connectors have solder buckets. Note : 05 connectors offer full compatiblity with MS series connectors. MTRI/INIS ontact Pin front insert Pin rear insert Socket insert Shell oupling ring Retaining ring round tab asket opper alloy/silver plating Synthetic rubber/lack Synthetic resin/lack Synthetic resin/lack luminum alloy/zinc plating, lack chromate finish luminum alloy/zinc plating, lack chromate finish opper alloy/zinc plating, Olive drab chromate finish opper alloy/silver plating Synthetic rubber/lack 1

60 05 Series Wire Size 05 ontact Size Wire Size #16 W#22-#16 #12 W#14-#12 #8 W#10-#8 #4 W#6-#4 Specification urrent rating ontact size #16 #2 #8 #4 Max. value per contact ielectric withstanding voltage (rms), 1minute 2000, 2800 or 3000 Insulation resistance 5000MΩ Min. at 500 Operating temperature -55 to +125 onnection 05 Series Plug Nonwateproof able lamps Waterproof Straight ackshell Staight Plug Waterproof Receptacle onnectors Nonwateproof able lamps Waterproof able lamps Waterproof ngle ackshell Right ngie Plug MS Series lexible onduit Waterproof able lamps Straight Plug Wall Mounting Receptacle Straight Piug able onnecting Receptacle lexible onduit lexible onduit acketed able onduit Right ngle Plug ox Mounting Receptacle 2

61 05 Series ist of 05 Series Insert No. Receptacle Plug Note 10S S-3P P P P P P P () P () P P- Waterproof able lamp or onduit S-3S- Without ack Shell Type or onduit S-3S--SS Straight ack Shell Type (265) S-3S--S ngle ack Shell Type S- Without ack Shell Type or onduit S--SS Straight ack Shell Type (265) S--S ngle ack Shell Type S- Without ack Shell Type or onduit S--SS Straight ack Shell Type (265) S--S ngle ack Shell Type S- Without ack Shell Type or onduit S--SS Straight ack Shell Type (265) S--S ngle ack Shell Type S- Without ack Shell Type or onduit S--SS Straight ack Shell Type (265) S--S ngle ack Shell Type S- Without ack Shell Type or onduit S--SS Straight ack Shell Type (265) S--S ngle ack Shell Type S- Without ack Shell Type or onduit S--SS Straight ack Shell Type (265) S--S ngle ack Shell Type S- Without ack Shell Type or onduit S--SS Straight ack Shell Type (265) S--S ngle ack Shell Type S- Without ack Shell Type or onduit S--SS Straight ack Shell Type (265) S--S ngle ack Shell Type S- Without ack Shell Type or onduit S--SS Straight ack Shell Type (265) S--S ngle ack Shell Type 05 3

62 05 Series Insert rrangements Insert No. 10S rrangements ontact Size #16 #12 #16 #12 #12 No. of ontacts Premating ontact Position Terminal Terminal Terminal Terminal Terminal oltage Rating Withstanding oltage urrent apacity 200 (rms) 250 (rms) 250 (rms) 250 (rms) 250 (rms) 2000 (rms) 3000 (rms) 2000 (rms) 2800 (rms) 2000 (rms) 13 (29.2) 23 (62.5) 13 (43.6) 23 (62.5) 23 (83.7) Insert No () () rrangements ontact Size #8 #12 #8 #8 #4 No. of ontacts Premating ontact Position Terminal Terminal Terminal Terminal Terminal oltage Rating Withstanding oltage urrent apacity 250 (rms) 250 (rms) 250 (rms) 250 (rms) 250 (rms) 3000 (rms) 2000 (rms) 2000 (rms) 2000 (rms) 2800 (rms) 46 (125.1) 23 (90.1) 46 (167.4) 46 (167.4) 80 (217.6) Note 1) The above figures show the views from solder cup side of 02-6 plug connectors (socket insert). 2) urrent capacities show the maximum permitted current values per contact. 4

63 05 Series lternate Insert Positions Z W Y X ront iew of Socket Insert Insert No. ontact size/ Number W X Y Z 10S-3 #16/ #12/ #16/ #12/ #12/ #8/ #12/ #8/ #4/

64 05 Series Receptacle PYS- 05 S STY 2 : ox Mounting Receptacle S SIZ 10S, 18, 20, 22, 24, 32 INSRT RRNMNT See page 4 ONTT STY P : Pin S OOR : lack N ST Omit : ess asket S : With asket TRNT INSRT POSITION Omit : Standard position W,X,Y,Z : lternate position PRMTIN ONTT POSITION Reter to insert arrangements ±1 φ ± 0.5 φ min ± ± 0.35 ± 0.15 ±1 Thread P/N S-3P- 5 / 8-24UN P / 8-18UN P P / 4-18UN P P / 8-18UN P P P- 1 1 / 2-18UN P- 2-18UNS

65 05 Series Plug SY--SS S STY 6:Straight plug S SIZ 10S, 18, 20, 22, 24, 32 INSRT RRNMNT See page 4 ONNTOR STY Omit:Without ack Shell (or onduit) SS:Straight Plug (With Straight ack Shell) S:Right ngle Plug (With Right ngle ack Shell) S OOR : lack 05 ONTT STY S:Socket TRNT INSRT POSITION Omit:Standard position W,X,Y,Z:ltemate Position PRMTIN ONTT POSITION Refer to insert arrangements Plug S - asket φ φ ±0.5 ±1 ±1 P/N oupling Threads Pear Threads S-3S- 5 / 8-24UN / 16-24UN S / 8-18UN UN S S- 1 1 / 4-18UN / 8-18UN S S- 1 3 / 8-18UN / 4-18UN S S- 1 1 / 2-18UN / 8-18UN S S- 2-18UNS / 8-16UN

66 05 Series Straight Plug S --SS W max 7.85 min 05 φ ± φ P/N oupling Threads Rear Threads W S-3S--SS 5 / 8-24UN / 8-24UN S--SS S--SS 1 1 / 8-18UN UN S--SS S--SS 1 1 / 4-18UN S--SS S--SS 1 3 / 8-18UN / 16-18UN S--SS S--SS 1 1 / 2-18UN / 16-18UN S--SS 2-18UNS / 4-18UNS-2 8

67 05 Series Right ngle Plug S --S max U ± 0.7 R ± 0.7 Y min φ W P/N oupling Threads Rear Threads W R U Y S-3S--S 5 / 8-24UN / 8-24UN S--S S--S 1 1 / 8-18UN UN S--S 1 1 / 4-18UN S--S / 16-18UN S--S 1 3 / 8-18UN S--S S--S S--S 1 1 / 2-18UN / 16-18UN S--S 2-18UNS / 4-18UNS

68 05 Series ccessories Waterproof Straight ack Shell 05- S-S- Material/inish luminum alloy/lack chromate finish S-S- is a waterproof backshell to hold a length of cable when no conduit is used. Set SRW (SUS/ON SPOT) W φ O-ring φ 7.85min Shell Size P/N 10S 05-10SS-S Threads 9 / 16-24UN-2 Threads W 5 / 8-24UN S-S UN UN S-S / 8-18UN / 16-18UN S-S / 4-18UN / 16-18UN S-S / 8-18UN / 16-18UN S-S / 8-16UN / 4-18UNS-2 10

69 05 Series Waterproof ngle ack Shell - -S (265) Material/inish luminum alloy/lack chromate finish - -S (265) is a waterproof backshell to hold a length of cable at right angle when no conduit is used. 1 max 05 2 max U R Y min O-ring φ W Shell Size P/N 1 2 R U Threads Threads W Y 5 / 8-24UN S -10S-S (265) / 16-24UN S (265) UN UN S (265) / 8-18UN / 16-18UN S (265) / 4-18UN / 16-18UN S (265) / 8-18UN / 16-18UN S (265) / 8-16UN / 4-18UNS

70 05 Series Waterproof able lamps (265) Material/inish luminium alloy/zinc Plating. lack chromate finish (265) is a waterproof cable clamp for use with a plug. The cable clamp body is the MS3057- that has a waterproof rubber bushing. Therefore, be sure to use a jacketed cable meeting one of the applicable cable size ranges as shown. The cable clamp should be used together with a waterproof backshell. 1.5 φ φ P/N Shell Size Threads ushing P/N able Outer iameter (265) 10S / 8-24UN ~ (265) ~ (265) UN ~ (265) ~ (265) ~ (265) 20, / 16-18UN ~ (265) ~ (265) ~19.1 / 16-18UN (265) ~ (265) / 4-18UN ~

71 05 Series ushing Material/inish Synthetic rubber (lack) is the bushing used on cable clamp part number (265) 05 φ φ φ P/N pplicable Washer MS3057-4W MS W MS W MS W MS W NOT : Please place an order for a washer separately from a bushing. 13

72 05 Series ap and hain ssembly (Not Waterproof) 05 Material/inish ap luminum alloy/lack chromate finish hain Stainless steel The cap and chain assembly protects the connector joint by preventing the intrusion of dust or other foreign substances that may impair the electrical connection. The cap for the receptacle (MS25043) comes with a drip-resistant gasket. MS (265) (or Plug) P/N Shell Size Threads MS (265) 10S 5 / 8-24UN MS (265) / 8-18UN MS (265) / 4-18UN MS (265) / 8-18UN MS (265) / 2-18UN MS (265) UNS MS (265) (or Receptacle) P/N Shell Size Threads MS (265) 10S 5 / 8-24UN MS (265) / 8-18UN MS (265) / 4-18UN MS (265) / 8-18UN MS (265) / 2-18UN MS (265) UN

73 ccessories Series of able lamps and ack Shells able lamp and ushing able lamps (Nonwaterproof Type for 01-6) MS3057- (247) Material/inish luminum alloy/zinc plating, lue chromate finish MS3057- is an accessory for use with a backshell to clamp a length of cable. The cable can be positioned exactly in the center of the cable clamp, because its structure is such that any cable can be fastened from both sides by two pressure bars. This cable clamp, which uses one of the synthetic rubber bushings shown in the specification list, can also be used for jacketed cable or bundled cable. If the cable to be used is much smaller in diameter than the bushing, a smaller bushing should be added. φ ushing φ P/N Shell Size Threads ushing P/N MS (247) UN N MS (247) 20, / 16-18UN N MS (247) 24, / 16-18UN N

74 ccessories Waterproof able lamps (for 01-6, 02-6) Material/inish luminum alloy/zinc plating, Olive drab chromate finish is a waterproof cable clamp for use with a plug in either the MS (190) series or the 01 or 02 series. The cable clamp body used the MS3057- that has a wateproof rubber bushing; therefore, be sure to use a jacketed cable meeting on of the applicable cable size ranges as shown. The cable clamp should be used together with a waterproof backshell. φ ushing P/N Shell Size Threads ushing P/N able Outer iameter 10..5~ UN ~ ~ ~ , / 16-18UN ~ ~ , ~19.1 / 16-18UN ~15.5 2

75 ccessories ushing Material/inish Synthetic rubber (lack) is the bushing used on cable clamp part number φ φ φ P/N pplicable Washer MS W MS W MS W 3

76 ccessories ack Shell (Nonwaterpoof Type) Straight ack Shell (for 01-6, 02-6) 01- S- NT No designation: Standard : ong backshell OOR No designation: lue : Olive drab Material/inish luminum alloy/hromate finish 01- S - is a backshell to hold a length of cable when no conduit is used. It is available in two different lengths to meet different wiring lengths. The backshell should be used together with a cable clamp. W φ φ P/N Shell Size Threads Threads W 01-18S UN 1-20UN 01-20S / 8-18UN 1 3 / 16 -UN 01-22S S S S S S / 4-18UN 1 3 / 16-18UN / 8-18UN 1 7 / 16-18UN / 8-18UN 1 7 / 16-18UN Note: Use a long backshell for an insert arrangement including contact #12 or #8. ngle ack Shell (for 01-6, 02-6) Nonwaterproof O-ring is employed in the angle backshell (see page 7) 4

77 ccessories ack Shell (Waterproof Type) Straight ack Shell (for 02-6) 02- S-S Material/inish luminum alloy/zinc plating, Olive drab chromate finish 02- S-S is a waterproof backshell to hold a length of cable when no conduit is used. W φ O ring φ P/N Shell Size Threads Threads W 02-18S-S UN 1-20UN 02-20S-S / 8-18UN 1 3 / 16-18UN 02-22S-S / 4-18UN 1 3 / 16-18UN 02-24S-S / 8-18UN 1 7 / 16-18UN 5

78 ccessories Straight ack Shell (for 01-6) 01- S-S NT No designation: Standard : ong backshell OOR No designation: lue : Olive drab Material/inish luminum alloy/hromate finish 01- S - S is a waterproof backshell to hold a length of cable when no conduit is used. When connected with a cable clamp. ( ) it provides waterproofing, oil resistant, and dustproofing properties. W φ O ring φ P/N Shell Size Threads Threads W 01-18S- S UN 1-20UN 01-20S- S / 8-18UN 1 3 / 16-18UN 01-22S- S S- S S- S S- S S- S S- S / 4-18UN 1 3 / 16-18UN / 8-18UN 1 7 / 16-18UN / 8-18UN 1 7 / 16-18UN 6

79 ccessories ngle ack Shell for 01-6, S (247) TYP S: waterproof type No designation: Not waterproof type OOR No designation: Olive drab (247): lue Material/inish luminum alloy/hromate finish - -S ( ) is a waterproof backshell to hold a length of cable at right angle when no coduit is used. When connected with a cable clamp ( ), it provides water-proofing, oil resistant and dustproofing properties. 1 max. 2 max. U R O ring φ W P/N Shell Size 1 2 R U Threads Threads W -18-S UN 1-20UN -20-S / 8-18UN 1 3 / 16-18UN -22-S / 4-18UN 1 3 / 16-18UN -24-S / 8-18UN 1 7 / 16-18UN 7

80 M Series Miniature ersion onforming to IS M series connectors conform to IS These connectors are used in a wide variety of industrial machinery applications. M TUR Miniature and igh ensity #20 and #16 contact sizes are available 5 key design prevents mis-mating Quick and asy Termination ontacts are pre-loaded in the connector. Solder cups are permanently oriented in one direction to simplify termination. U 94-0 materials used Optional dip solder termination SPIITION ontact size #20 #16 oltage rating (max.) 250 (rms), 350 urrent rating (max.) 5 10 Operating temperature -25 to +85 Insulation resistance 10000mΩ min. at 500 ielictric withstanding voltage 1000 (rms) at sea leval ontact resistance 5mΩ max. at 1 ibration 10-55z, mplitude: 1.5mm Shock cceleration 50 urability 500 cycles umidity (Steady state) 40, 90 to 95%, 96 hours Temperature cycle -40 to+100, 5cycles Salt spray 5%, 35, 48 hours ontact size W #20 W #16 Wire size Wire size onductor crossared W #20 or ess W #16 or ess MTRI/INIS Insert ontact Shell ood ap PT resin (U94-0)/lue opper alloy/silver or old plating Zinc alloy/lack, anti-corrosive treatment S resin (U94-0)/lack luminum alloy/lack, anti-corrosive treatment 1

81 M Series M Insert rrangements (ront iew of Male Insert) No. of ontacts Shell Size rrangements Insert No No. of ontacts Shell Size rrangements Insert No #16 Male contact #20 Male contact Note : onnector maiting side for plug shell (Standard insert position) lternate Insert Positions No. of ontacts Insert Number X Y Z Master eyway X Y X Z Y Z ront view of pin insert lternate Position mark MSP2524MX S STY SP: Straight Plug P: ngle Plug R: ox Mounting Receptacle WR: Wall Mounting Receptacle R: able onnecting Receptacle W: ngle Wall Receptacle : ngle able Receptacle INSRT RRNMNT See table ONTT STY M: Male (Pin) : emale (Socket) TI STY/OO MTRI Omit: Solder cup/plastic hood : ip solder tail (Shell style R only) M: Solder cup/metal hood ONTT PTIN Omit: Silver Plating : old plating TRNT INSRT POSITION Omit: Standard position X, Y, Z: lternate position 2

82 M Series Straight Plug Plastic ood Type MSP M Shell Size ±1 13 M ~ M ~ M ~ M ~ Metal ood Type MSP M φ φ φ φ Shell Size ±1 13 M ~ M ~ M ~ M ~

83 M Series M Right ngle Plug Plastic ood Type MP Shell Size ±1 13 M ~ M ~ M ~ M ~ Metal ood Type MP M φ φ φ Shell Size ± M ~ M ~ M ~ M ~

84 M Series Wall Mounting Receptacle Plastic ood Type MWR M 2.0 ± ±1.0 5min (3) φ Shell Size ±0.2 ± M ~ M ~ M ~ M ~ Metal ood Type MWR M φ ±1.0 5min 2.0 ±0.3 φ φ Shell Size ±0.2 ± M ~ M ~ M ~ M ~

85 M Series M able onnecting Receptacle Plastic ood Type MR 5min Shell Size 13 M ~ M ~ M ~ M ~ Metal ood Type MR M 5min φ φ Shell Size 13 M ~ M ~ M ~ M ~

86 M Series Right ngle Wall Mounting Receptacle Metal ood Type MW M M φ Shell Size ±0.2 ± M ~ M ~ M ~ M ~ Right ngle able Receptacle Metal ood Type M M φ Shell Size 13 M ~ M ~ M ~ M ~

87 M Series M ox Mounting Receptacle MR Solder up Type 2.0 ± ± 1.0 5min φ max(φ1.0ontacts) 27.4max(φ1.6ontacts) Shell Size ±0.2 ± M M M M ip Solder Type φ Shell Size ±0.2 ±0.5 ± M M M M

88 M Series P... Mounting oles for ip Soldering Type M φ φ Panel ut-out (for MR/MWR/M/MW) ± 0.2 φ3.5 ± 0.2 M1, M2 ± 0.2 Shell size M 1 M 2 Y Y min M 1 : ront mounting holes dia. (Shell style R only) M 2 : Rear mounting holes dia. 9

89 M Series M ap MP25 P STY P : Plug cap R : Receptacle cap S SIZ 13, 16, 21, 25 Plug ap MP 100 Shell size ±1 13 M M M M φ Receptacle ap MR 100 Shell size ±1 13 M M M M φ4.2 10

90 Series Moistureproof Type ayonet ock oupling series connectors meet the performance criteria of most factory automation applications. They withstand exposure to moisture, oil and vibration. Resilient insulator provides improved environmental sealing. SPIITION ontact size #20 #16 oltage rating (max.) 250 (rms), 350 urrent rating (max.) 5 10 Operating temperature -25 to +85 Insulation resistance 1000MΩ min. at 500 ielectric withstanding voltage 1000 (rms) at sea level ontact resistance 5mΩ max. at 1 ibration 10-55z, mplitude: 1.5mm Shock cceleration 50 urability 500 cycles umidity (Steady state) 40, 90 to 95%, 96 hours Tempertaure cycle -40 to + 100, 5 cycles Salt spray 5%, 35, 48 hours Wire size ontact W #20 W #16 Wire size W #20 or ess W #16 or ess MTRI/INIS Insulator ontact Shell ood ushing ap hloroprene synthetic rubber/lack opper alloy/silver or old plating Zinc alloy/olive drab chromate finish luminum alloy/olive drab chromate finish hloroprene synthetic rubber/lack hloroprene synthetic rubber/lack or Metal/Olive drab chromate finish 1

91 Series Insert rrangements (ront iew of Male Insert) Shell Size No. of ontacts rrangements Insert No Shell Size No. of ontacts rrangements Insert No φ1.0mmontacts φ1.6mmontacts Note : onnector mating side for plug shell (Standard insert position) SP2524MXS S STY SP: Straigt Plug P: ngle Plug R: ox Mounting Receptacle WR: Wall Mounting Receptacle R: able onnecting Receptacle W: ngle Wall Mounting Receptacle : ngle able onnecting Receptacle N ST Omit: ess asket S: With asket ONTT PTIN Omit: Silver plating : old plating INSRT RRNMNT See table TRNT INSRT POSITION Omit: Standard position X, Y, Z: lternate position ONTT STY M: Male (pin) : emale (Socket) Shell Size ±0.5 φ± Shell Size ±0.5 φ±

92 Series lternate Insert Positions Z Y X Insert No. ontact Size/ No. of ontacts X Y Z 1303 #16/ #20/ #16/ #20/ #20/ #20/ #16/ #20/ #20/ ront view of pin insert SP Straight Plug SP φ φ φ φ φ () () Shell +0 ±0.5 ±0.5 ±1 Size -0.3 ±

93 Series P ngle Plug P φ φ () () () φ Shell Size ±0.5 ±0.5 ± R ox Mounting Receptacle R φ φ φ φ ±1 2.0 ± (30) Shell Size ±0.5 ±0.3 ±0.2 ±

94 Series WR Wall Mounting Receptacle WR φ φ φ φ φ φ ±1 2.0 ±0.3 () () Shell +0 ±0.5 ±0.5 ±0.3 ±0.2 ±0.5 Size -0.3 ± W ngle Wall Mounting Receptacle W φ φ φ () 6.7 () 10.5 ±1 2.0 ± 0.1 () φ Shell +0 ±0.5 ±0.5 ±0.3 ±0.2 ±0.5 Size

95 Series R able onnecting Receptacle R φ φ φ φ φ 6.7 () () Shell +0 ±0.5 ±0.5 ±1 Size -0.3 ± ngle able onnecting Receptacle φ () φ 6.7 () () φ Shell Size ±0.5 ±0.5 ±

96 Series Panel ut-out (for R/WR/) ± 0.2 φ3.5 ± 0.2 M1.M2 ± 0.2 Shell Size M 1 M 2 Y M 1 : ront mounting holes dia. (Shell style R only) M 2 : Rear mouting holes dia. Y min ( 同一 Shell Size) ap P25R P STY P: Plug cap R: Receptacle ap MTRI Omit: Metal R: Rubber R: Receptacle cap S SIZ 13, 16, 21, 25 Rubber Type P R (Plug ap) R R (Receptacle ap) φ Size Size 150 ± ± 20 φ φ3.2ole φ3.2ole 7

97 Series Metal Type P (Plug ap) R (Receptacle ap) φ φ 130 ± ±10 27 φ4.2ole φ4.2ole P/N φ±0.5 P P P P P/N φ±0.5 R R R R

98 W Series Waterproof Miniature ircular onnector W series connectors meet the performance criteria of most factory automation applications as they are water - proof and withstand exposure to water, oil and vibration. TUR Mating ock Mechanism Rotating plug connector 90 degrees after mating makes click sound to confirm locking and releasing exactly. Miniature & igh ensity Miniature and high density insert arrangements are same as M Series connectors (conforming to IS--5432). Positioning ey 5 positioning keys on the shell provide exact mating. asy and Quick Termination ontacts are pre-loaded in the connector. The solder cups are permanently oriented in one direction to simplify termination. U standard insulator material Waterproof, satisfying IP67 criteria in mating condition W SPIITION oltage rating (max.) 250 (rms), 350 urrent rat - Pin contact ia 1.0mm 1.6mm ing (max.) urrent Rating (max.) 5 10 onductor ia 1.0mm max. 1.5mm max. pplicable Wire onductor Sectional 0.5mm rea max. 1.25mm 2 max. Operating temperature -25 to +85 Insulation resistance 1000MΩ min. at 500 ielectric withstanding voltage 1000 (rms) at 1minute ontact resistance 5mΩmax. at 1 ibration 10-55z, mplitude: 1.5mm Shock cceleration 50 urability 500 cycles umidity (Steady state) 40, 90 to 95%, 96 hours Tempertaure cycle -40 to + 100, 5 cycles Salt spray 5%, 35, 48 hours 1

99 W Series MTRI/INIS W Insulator Poly Phenylen Sulfide Resin (U94-0) / lue ontact opper lloy / Silver Plating (standard), old Plating (option) Shell Zinc lloy / Olive rad hromate inish able lamp luminum lloy / Olive rab hromate inish ushing Synthetic Rubber / lack ap Synthetic Rubber / lack, Zinc lloy / Olive rab hromate inish No. of ontacts Shell Size rrangements Insert No No. of ontacts Shell Size rrangements Insert No φ1.0mm ontacts φ1.6mm ontacts Note : ront iew of Male Insert lternate Insert Positions Shell Size θ1 θ2 θ3 No. of ontacts X Y Z θ2 θ1 X Z Y θ3 Master eyway lternate Position mark Pin ontact 2

100 W Series Insert rrangements (ront iew of Male Insert) WSP2524MXS-1 S STY SP: Straigt Plug R: ox Mounting Receptacle WR: Wall Mounting Receptacle R: able onnecting Receptacle ushing Size N ST Omit: ess asket S: With asket W S SIZ 13, 16, 21, 25 ONTT 03, 05, 07, 10, 16, 19, 24, 28, 32 ONTT PTIN Omit: Silver plating : old plating TRNT INSRT POSITION Omit: Standard position X, Y, Z: lternate position ONTT STY M : Male (Pin) : emale (Socket) Shell Size ±0.5 φ± Shell Size ±0.5 φ±

101 W Series WSP (Straight Plug) φ φ W lat rea Width: Shell Size Shell Size No. of ontacts Male onnector P/N emale onnector P/N ushing Inner ia (φmm) pplicable able ia Range (φmm) 3 WSP1303M-1 WSP ~9.0 5 WSP1305M-1 WSP ~9.0 7 WSP1607M-2 WSP ~ WSP1610M-2 WSP ~ WSP2104M-1 WSP ~ WSP2104M-2 WSP ~ WSP2104M-3 WSP ~8.7 7 WSP2107M-1 WSP ~ WSP2107M-2 WSP ~ WSP2107M-3 WSP ~ WSP2110M-1 WSP ~ WSP2110M-2 WSP ~ WSP2110M-3 WSP ~ WSP2116M-1 WSP ~ WSP2116M-2 WSP ~ WSP2116M-3 WSP ~ WSP2119M-1 WSP ~ WSP2119M-2 WSP ~ WSP2119M-3 WSP ~ WSP2516M-1 WSP ~ WSP2516M-2 WSP ~ WSP2516M-3 WSP ~ WSP2516M-7 WSP ~ WSP2524M-1 WSP ~ WSP2524M-2 WSP ~ WSP2524M-3 WSP ~ WSP2524M-7 WSP ~ WSP2528M-1 WSP ~ WSP2528M-2 WSP ~ WSP2528M-3 WSP ~ WSP2528M-7 WSP ~ WSP2532M-1 WSP ~ WSP2532M-2 WSP ~ WSP2532M-3 WSP ~ WSP2532M-7 WSP ~17.0 4

102 W Series WWR (Wall Receptacle) φ3.2(4 Places) φ φ Shell Size Shell Size No. of ontacts Male onnector P/N Note : "S" is indicated in for products with Panel asket. No designation for ess asket lat rea Width: emale onnector P/N ushing Inner ia (φmm) pplicable able ia Range (φmm) 3 WWR1303M -1 WWR ~9.0 5 WWR1305M -1 WWR ~9.0 7 WWR1607M -2 WWR ~ WWR1610M -2 WWR ~ WWR2104M -1 WWR ~ WWR2104M -2 WWR ~ WWR2104M -3 WWR ~8.7 7 WWR2107M -1 WWR ~ WWR2107M -2 WWR ~ WWR2107M -3 WWR ~ WWR2110M -1 WWR ~ WWR2110M -2 WWR ~ WWR2110M -3 WWR ~ WWR2116M -1 WWR ~ WWR2116M -2 WWR ~ WWR2116M -3 WWR ~ WWR2119M -1 WWR ~ WWR2119M -2 WWR ~ WWR2119M -3 WWR ~ WWR2516M -1 WWR ~ WWR2516M -2 WWR ~ WWR2516M -3 WWR ~ WWR2516M -7 WWR ~ WWR2524M -1 WWR ~ WWR2524M -2 WWR ~ WWR2524M -3 WWR ~ WWR2524M -7 WWR ~ WWR2528M -1 WWR ~ WWR2528M -2 WWR ~ WWR2528M -3 WWR ~ WWR2528M -7 WWR ~ WWR2532M -1 WWR ~ WWR2532M -2 WWR ~ WWR2532M -3 WWR ~ WWR2532M -7 WWR ~17.0 W 5

103 W Series WR (able Receptacle) φ φ W lat rea Width: Shell Size Shell Size No. of ontacts Male onnector P/N emale onnector P/N ushing Inner ia (φmm) pplicable able ia Range (φmm) 3 WR1303M-1 WR ~9.0 5 WR1305M-1 WR ~9.0 7 WR1607M-2 WR ~ WR1610M-2 WR ~ WR2104M-1 WR ~ WR2104M-2 WR ~ WR2104M-3 WR ~8.7 7 WR2107M-1 WR ~ WR2107M-2 WR ~ WR2107M-3 WR ~ WR2110M-1 WR ~ WR2110M-2 WR ~ WR2110M-3 WR ~ WR2116M-1 WR ~ WR2116M-2 WR ~ WR2116M-3 WR ~ WR2119M-1 WR ~ WR2119M-2 WR ~ WR2119M-3 WR ~ WR2516M-1 WR ~ WR2516M-2 WR ~ WR2516M-3 WR ~ WR2516M-7 WR ~ WR2524M-1 WR ~ WR2524M-2 WR ~ WR2524M-3 WR ~ WR2524M-7 WR ~ WR2528M-1 WR ~ WR2528M-2 WR ~ WR2528M-3 WR ~ WR2528M-7 WR ~ WR2532M-1 WR ~ WR2532M-2 WR ~ WR2532M-3 WR ~ WR2532M-7 WR ~17.0 6

104 W Series WR (ox Receptacle) φ3.2(4 Places) Thread φ φ ffective Thread ength W Shell Size No. of ontacts Male onnector P/N emale onnector P/N 3 WR1303M WR M16 5 WR1305M WR M16 7 WR1607M WR M20 10 WR1610M WR M20 4 WR2104M WR M24 7 WR2107M WR M24 10 WR2110M WR M24 16 WR2116M WR M24 19 WR2119M WR M24 16 WR2516M WR M28 24 WR2524M WR M28 28 WR2528M WR M28 32 WR2532M WR M28 Note : "S" is indicated in for products with Panel asket. No designation for ess asket. 7

105 W Series WR WWR Panel utout imension and Space between 2 onnectors (Same Shell Size) W Ymin. 8-φ φm1 min. : ront Mounting φm2 min. : Rear Mounting Mounting ole Position ront Mounting ole ia Rear Mounting ole ia Space between 2 onnectors Shell Size ±0.2 M1 min. M2 min. Y min In the case of rear mounting, maximum panel thickness is 3mm for products less gasket and 2mm for products with gasket. Panel Mating Side (ront to Panel) (Rear to Panel) 8

106 W Series ap P25R P STY P: Plug cap R: Receptacle ap MTRI Omit: Metal R: Rubber R: Receptacle cap S SIZ 13, 16, 21, 25 W Rubber Type P R (Plug ap) R R (Receptacle ap) φ Size 150 Size 150 φ φ3.2 ole φ3.2 ole P/N φ P13R P16R P21R P25R P/N φ R13R R16R R21R R25R

107 W Series Metal Type P (Plug ap) R (Receptacle ap) W 130 φ φ 27 φ4.2 ole φ4.2 ole P/N φ P P P P P/N φ R R R R

108 M04T Series 8-Pole/M12-Size Small Sized & Sealed ircular onnectors arious kinds of industrial devices (sensors, actuators). lso available for heavy duty deviceb having sealed type design. M04T TUR Sealed type design : IP67 U94-0 insulator flammability rating Small size & high density : 8-pole/M12 size Overmold style cable assembly SPIITION oltage rating 30 /36 urrent rating 1.5 /contact Insulation resistance 100MΩ min. at 250 ielectric withstanding voltage 1000 (rms) 1minute Operating temperature range -40~+85 Number of contacts 8 able for plug & jack cable assembly Shielded cable with 7-conductor, W22 Wire for plug receptacle wire assembly U1007, 0.3mm sq MTRI/INIS ITM PU PU RPT Insulator Plastic(U94-O)/gray ontact opper alloy/gold plating oupling ring Zinc alloy/nickel plating Shell Zinc alloy/nickel plating Nut opper alloy/nickel plating 0-ring Synthetic rubber/black Synthetic rubber/black 1