Cover. Finishes/Colors/ Powder Coat FINISH PLASTIC METAL

Transcription

1 1450 Features The 1450 cast aluminum closer was specially designed to deliver consistent, dependable, long-term performance in frequently-used, low-abusive traffic areas. The patented design, featuring the industry's most common hole pattern, is an excellent choice for a range of applications - from aftermarket replacement to aluminum store fronts, to new construction projects - anywhere quality, reliability and value are important. Certifications body Construction Fluid Handing Grade 1 - NSI 156.4, UL 10C, D, 100 Hour Salt Spray, Meets - uy merican ct n Cast luminum ody n Full Complement earing n 1-1/4 Diameter Piston n 5/8 Diameter Single Heat Treated Pinion Journal ll Weather Fluid Non-Handed Templating Peel-n-Stick templates - 3/4 x 12 Mounting Hole Pattern Size djustable Spring Size 1-6 Warranty 25 years Cover Fasteners mounting rms Finishes/Colors/ Powder Coat n Slim Line Plastic, Standard n Full Plastic and Metal, Optional Universal Screw Pack (UNIV) Hinge (Pull Side), Top Jamb (Push Side), Parallel rm (Push Side) Standard regular pull side, and top jamb n luminum (689) n Statuary ronze (690) n Light ronze (691) n lack (693) n Dark ronze (695) n rass (696) n Custom colors optional SRI primer - powder coat only Special Templates Customized installation templates or products may be available to solve unusual applications. Contact LCN Product Support for assistance. HINGE (PULL) SIDE MOUNTING TOP JM (PULL) TOP JM (PUSH) PRLLEL RM STOP FCE PINT POWDER COT PLTED FINISH PLSTIC METL COVER NON-HNDED NON-SIZED CCESSIILITY CYLINDER DELYED CTION REGULR (DOULE) STNDRD (SINGLE) HOLD-OPEN * *RM FUNCTION ED/HED * CUSH/HCUSH SCUSH/SHCUSH VILLE NOT VILLE Closer available with less than 5.0 lbs. opening force on 36 door. * Maximum opening/hold-open point with standard template. D = For designer series only. LCN Door Control Catalog C1

2 450 Mounting details inge (Pull) Side ounting 2-15/16" 75 mm 3/4" 19 mm 68 mm 1-3/8" 35 mm 11-13/16" 300 mm 68 mm 2-1/8" 54 mm REGULR-PULL SIDE The '' dimension refers to the edge of the closer body to the center line of pivot or hinge. The '' dimension refers to the edge of the closer shoe bracket to the center line of pivot or hinge. butt Hinges Should not exceed 5 (127 mm) in width uxiliary Stop Recommended at hold-open point or where a door cannot swing 180 Reveal Should not exceed 3/4 (19 mm) for regular arm or 1/2 (13 mm) for hold-open arm Top Rail n Less than 2-1/2 (64 mm) requires PLTE, n With Full cover, use PLTE, FC. Plate requires 1-1/2 (38 mm) minimum Clearance 2-3/8 (60 mm) behind door required for installation maximum opening 100 : = 7 (102 mm) = 12-3/8 (314 mm) 101 to 130 : =5-1/2 (140 mm) = 10-7/8 (276 mm) 131 to 180 : =4 (140 mm) = 9-3/8 (238 mm) Hold-open points up to maximum opening with hold-open arm *Frame and trim permitting. 20 LCN Door Control Catalog

3 1450 Mounting details Top Jamb (Push Side Mountin 2-9/16" 65 mm 11-3/4" 299 mm 3/4" 19 mm 1-5/8" 42 mm 68 mm The '' dimension refers to the edge of the closer body to the center line of pivot or hinge. The '' dimension refers to the edge of the closer shoe bracket to the center line of pivot or hinge. butt Hinges Should not exceed 5 (127 mm) in width uxiliary Stop Recommended at hold-open point or where a door cannot swing 180 Reveal rm Type Reveal Max Opening Regular rm 5 Up to 170 Regular rm 3-3/4 Up to 180 Long rm 8 Up to 155 Hold-Open rm 2-3/4 Up to 180 Long Hold-Open rm 4-7/8 Up to 140 Top Rail Requires 2-1/8 (54 mm) minimum. 3-3/8 (86 mm) minimum with closer on PLTE, Head Frame Less than 1-3/4 (44 mm) requires PLTE, For flush ceiling condition with 1-3/4 (45 mm) head frame, use PLTE, maximum opening 100 : =7 (102 mm) = 12-3/8 (314 mm) 101 to 130 : = 5-1/2 (140 mm) = 10-7/8 (276 mm) 131 to 180 : = 4 (102 mm) = 9-3/8 (238 mm) Hold-open points up to maximum opening with hold-open arm. *Frame and trim permitting. LCN Door Control Catalog C2

4 450 Mounting details arallel rm Push Side) Mounting 4" 102 mm 5-3/8" 136 mm 2-1/8" 54 mm 20-3/8" 517 mm 4-1/8" 105 mm butt Hinges uxiliary Stop Top Rail Should not exceed 5 (127 mm) in width Recommended at hold-open point, where a door cannot swing 180, or where CUSH-N-STOP arm is not used n Less than 5-1/4 (133 mm) measured from the soffit requires n Plate requires 1-1/4 (32 mm) minimum. Clearance Cover Plastic Metal Minimum Top Rail (measured from soffit) P shoe projects 4-1/8 (105 mm) from door face Plate Required 3-1/2 (89 mm) /4 (57 mm) P 3-1/2 (89 mm) FC 2-1/4 (57 mm) PFC Head Frame Flush or single rabbeted requires P SHOE DPTER, Stop Width Minimum 1 (25 mm) blade Stop Clearance, requires 1/2 (13 mm) LDE STOP SPCER, uxiliary Shoe maximum opening allows installation of regular arm with overhead holder/stop Regular or hold-open arm can be templated to 120 : = 3-3/16 (81 mm) = 8-7/8 (225 mm) 121 to 180 : = 11/16 (17 mm) = 6-3/8 (162 mm) Notes: P shoe is included with Rw/P rm 1450 closer includes FIFTH HOLE SPCER to support P SHOE Hold-open points up to maximum opening with hold-open arm. 22 LCN Door Control Catalog

5 ED/HED mount 4" 102 mm mm 20-13/16" 528 mm 5-11/16" 145 mm 2-1/8" 54 mm 4-9/16" 116 mm Mounting details ED and CUSH -N-STO mountin CuSH/HCuSH/SCuSH /SHCuSH mount 4" 102 mm 68 mm 20-13/16" 528 mm 5-11/16" 145 mm 2-1/8" 54 mm 4-9/16" 116 mm The '' dimension refers to the edge of the closer body to the center line of pivot or hinge. The '' dimension refers to the edge of the closer shoe bracket to the center line of pivot or hinge. Clearance ED or CUSH shoe projects 5-11/16 (144mm) from door face Head Frame Flush or rabbeted requires CUSH FLUSH PNEL DPTER, ED or CuSH Rm Spring CuSH maximum opening Requires soffit SHOE SUPPORT, for fifth screw anchorage where reveal is less than 3-1/16 (78 mm) Dead stop points are approximately 5 more than templated stop points ED template allows 110. Hold-open point up to maximum opening 120 : = 8-7/8 (225 mm) = 3-3/16 (81 mm) over 120 : = 6-3/8 (162 mm) = 11/16 (17 mm) Note: 1450 closers ordered with ED, CUSH or SPRING CUSH arms include FIFTH HOLE SPCER to support the shoe. CUSH arms can be templated for maximum opening/ hold-open point at : = 10-3/8 (279 mm) = 4-15/16 (140 mm) 90 : = 9-5/8 (244 mm) = 4-3/16 (106 mm) 95 : = 8-7/8 (225 mm) = 3-7/16 (87 mm) 100 : = 8-1/4 (210 mm) = 2-13/16 (71 mm) 105 : = 7-5/8 (194 mm) = 2-3/16 (56 mm) 110 : = 7 (178 mm) = 1-9/16 (40 mm) LCN Door Control Catalog C2

6 450 ccessories Cylinders Covers lternate Cover Left hand shown Cast luminum Cylinder ssembly Slim Line Plastic Cover mC Metal Cover lT lternate Cover n Handed n Standard n Standard, sold separately (not packed with closer) FC Full Plastic Cover Installation ccessories / FC Plate P / PFC Plate CUSH Shoe Support lade Stop Spacer n Required for hinge side mount where top rail is less than 2-1/2 (64 mm) n Required for top jamb mounting where head frame is less than 1-3/4 (44 mm) or flush ceiling condition exists n Requires minimum 1-1/2 (38 mm) minimum top rail or 1-1/4 (32 mm) head frame n Required for parallel arm mounting where top rail is less than 4-3/8 (111mm), measured from the stop n Requires 1-3/4 (44 mm) minimum top rail n With full cover, use PLTE, FC n Provide anchorage for fifth screw used with CUSH arms where reveal is less than 3-1/16 (78mm) n Lowers parallel arm shoe to clear 1/2 (13 mm) blade stop. n With full cover, use PLTE, FC P P Shoe uxiliary Shoe P Flush Panel dapter n Required for parallel arm mounting n Requires a top rail of 7 (178mm). Optional shoe replaces -62P for parallel arm mounting of regular arm with overhead holder/stop n Provides horizontal mounting surface for P, ED or CUSH shoe on single rabbeted or flush frame 24 LCN Door Control Catalog

7 1450 ccessories rms Regular rm w/p l Long rm Hold-Open rm w/p l Long Hold-Open rm n Mounts hinge side or top jamb n Includes P SHOE, P required for parallel arm mounting n Includes LONG ROD ND SHOE, LR for top jamb mount with deep reveals n Mounts hinge side, top jamb or parallel arm (62P required) n Hold-open adjustable at shoe n Includes LONG HED ND TUE, L for top jamb mount with deep reveals ED Extra Duty rm n Features solid forged steel main and forearm for potentially abusive installations ED/G for blade stop clearance ED/62G Extra Duty rm w/ 62G n Features solid forged steel main and forearm for potentially abusive installations ED/G for blade stop clearance ED Hold-Open Extra Duty rm n Handed arm n Provides hold-open function adjustable at shoe CNS Cush-n-Stop rm n Features solid forged steel main arm and forearm with stop in soffit shoe CNS HCUSH rm n Provides hold-open function with templated stop/hold-open points n Handle controls hold-open function SCNS Spring CUSH rm n For abusive applications features solid forged steel main arm and forearm with spring loaded stop in the soffit shoe SCNS Spring HCUSH rm n For abusive applications features solid forged steel main arm and forearm with spring loaded stop in the soffit shoe n Handle controls hold-open function LCN Door Control Catalog C2

8 450 rdering Information Closer options How-to-order 1450 closers Select finish Standard Powder Coat luminum, Dark ronze, Statuary, Light ronze, lack, rass Cover Full Plastic (FC) Metal (specify right or left hand) (MC) lternate Cover (LT) (sold separately from product) Finish Custom Powder Coat (RL) (Metal cover required) SRI primer rm Regular w/62p (Rw/P) Long (LONG) Regular w/62 (Rw/62) Hold-Open w/62p (Hw/P) Long Hold-Open (HLONG) Extra Duty (ED) (optional -62G) Hold-Open Extra Duty (HED) - specify handing Cush-N-Stop (CUSH) HCush (HCUSH) Spring Cush (SCUSH) Spring HCush (SHCUSH) Closer will be shipped with: - Standard cylinder - Standard cover - Tri pack arm (Rw/P) - Universal screw pack unless options listed below are selected. Optional screw packs TORX Machine Screw (TORX) T* & TORX Machine Screw (TTORX) * Specify door thickness if other than 1-3/4 Table of sizes Installation accessories Plate, Plate, FC Plate, P Plate, PFC CUSH Shoe Support, lade Stop Spacer, uxiliary Shoe, P Flush Panel dapter, Special template ST- meets buy merican ct n Select closer based on width of door. n The spring power of a 1450 cylinder is field adjustable from size 1 through size 6 and is shipped adjusted to size 3. Exterior (and vestibule) door width Interior door width mm mm mm mm mm mm mm mm mm mm mm *1450 size 3 size 4 size 5 size 6 *1450 size 2 size 3 size 4 size 5 size 6 Minimum door width Minimum door width Indicates recommended range of door width for closer size. * djustable Size 1 thru 6. Reduced opening force 1450 closers CuTION! ny manual door closer, including those certified by HM to conform to NSI Standard 156.4, that is selected, installed and adjusted based on D or other reduced opening force requirements may not provide sufficient power to reliably close and latch a door. Refer to POWER OPERTORS section for information on systems that meet reduced opening force requirements without affecting closing power. * Maximum opening force. DOOR WIDTH * lbs * lbs LCN Door Control Catalog