AC Fans. AC Fans Overview 117. AC Axial Fans 118. AC Radial Fans 138. Technology. DC Axial Fans. DC Radial Fans. Specials. ACmaxx Axial Fans.
|
|
- Vincent Lawson
- 6 years ago
- Views:
Transcription
1 4
2 AC Fans AC Fans Overview 7 AC Axial Fans 8 AC Radial Fans 38 AC Radial Fans AC Axial Fans AC Fans ACmaxx Axial Fans Technology DC Axial Fans Specials DC Radial Fans 5 Accessories
3 AC Fans Technical Informations Program The renowned ebm-papst AC fans are used when DC voltage is not available. The AC range of fans is based on experience gained from decades of development activity, millions of units in series production and competence in innovation of a world-wide technological leader. A wide range of fans for AC operation are presented in this catalogue. In addition to complete equipment fans, you will also find fans without external housing, providing a particularly economical advantage when the air duct can be integrated in the respective appliance. Variety of sizes AC fans are available in a variety of sizes with either air exhaust or air intake over struts. Silent running models with sleeve bearings or for extreme ambient conditions; Fans with ball bearings are available pin connection or freehanging leads. Shaded-pole or capacitor motors Fan drive by shaded-pole or capacitor motors most of which incorporate the world-famous ebm-papst external rotor principle: The fan blades are directly attached to the external rotor of the external rotor motor thus combining both high performance and profitability. Flat built AC fans ebm-papst also has particularly flat built AC fans with internal rotor motor. Their advantage being, quick start to full speed. A plastic impeller and the both smaller and lighter internal rotor motor lead to a lower moment of inertia. Bearings AC fans with sleeve bearings are powered by Class E insulated motors. Fans with ball bearings are equipped with Class B, E or F insulated motors. Protection class All ebm-papst fans conform to the requirements of IP 0. Fans conforming to IP 54 and special types of protection class are also available. AC voltage The line of AC fans for Euro voltage according to IEC 38 (30 V + 6 %, -0 %) is basically also available for 5 V. Frequencies AC fans can be operated at frequencies of 50 Hz or Hz. However, their technical data then changes accordingly. Capacitor Fans driven by capacitor external motors provide particularly high operating efficiency. Generally, the required phase-shift capacitor is already integrated in the fan housing. Overloading Almost all AC fans are protected against overloading (e.g. due to blocked rotor) the drive motors are either impedance protected (marked Impedance protected, and/or Z.P. ) or are equipped with a thermal switch (marked Thermally protected or Th.P. ). The model designation of these fans ends with S. 6
4 Axial- and Radial Fans for AC Operation Overview Dimension Series ge Technology mm m 3 /h x A x N Ø 76 x TA Ø 76 x TV x x x x N x Z Ø 3 x TA Ø 08 x TZ x x x 7 x Ø 50 x Ø 50 x Ø 7 x Ø 5 x 80 W** Ø 3 x 80 W* x 80 WE x 37 RL x 38 RG x RG x 56 RG Ø 38 x RER Ø 76 x 54 RER DC Axial Fans DC Radial Fans Specials Overview of technically feasible designs Dimension SINTEC-Sleeve Bearings/ Axial-/Radial Fans Series mm OPTIONAL P A 80 x 80 x 38 yes / N 80 x 80 x 38 yes / TA 76 Ø x 37 yes / TV 76 Ø x 37 yes / x 9 x 5 yes / x 9 x 38 yes / x 9 x 5 yes / 4 00 N 9 x 9 x 38 yes / 5 00 Z 9 x 9 x 38 yes / 6 40 TA 3 Ø x 37 yes / 7 40 TZ 08 Ø x 37 yes / x 7 x 38 yes / x 35 x 38 yes x 7 x 38 yes Ø x 55 yes Ø x 55 yes Ø x 5 yes 34 RL 90 x x 37 yes / 38 RG x 35 x 38 yes / 39 RG 5 80 x 80 x yes RG 0 x 0 x 56 yes 4 RER 5 38 Ø x yes 4 RER 76 Ø x 54 yes 43 availably unavailably Sleeve-Bearings VDE, UL, CSA Sensor Humidity protection IP >= IP54 Salt fog protection ge Information Pictograms On the pages of the catalogue and on the following overview pages, the pictograms illustrated below provide information about technically possible special versions in the fan line presented. Please note that these special versions are not possible for all voltages and speeds, and not in all combinations. The special versions are designed for specific customers and projects and are not usually available off the shelf. Speed Signal The fan uses a separate wire to output information about its speed, and thus about the speed of the rotor. For technical details, please refer to page 90. HP IP54 SP Protection against moisture Protection for the fan's electronics against moisture and condensation. For details, please refer to page 0. IP 54 Protection of motor and PCB board against splashed water and humidity. For details, please refer to page 0. Protection against salt spray fog Protection of fan against the damaging effects of salt spray fog. For details, please refer to page 0. 7 Accessories AC Radial Fans AC Axial Fans ACmaxx Axial Fans
5 Series 8000 A 80 x 80 x 38 mm AC fans with external rotor shaded-pole motor. Impedance protected against overloading. Metal fan housing and impeller. Air intake over struts. Rotational direction CW looking at rotor. Electrical connection via flat pins.8 x 0.5 mm. Fan housing with ground lug and screw M4 x 8 (TORX). Mass: 490 g. Also available with electrical connection via leads. Also available with air-exhaust over struts and of rotation cw Type m 3 /h CFM V Hz db(a) Bel / Watt min - C Hours Hours 8880 A / / A / / A / / A / / A / / A / / A / / A / / Series 8000 A with mounting bosses 0,05 0,0 0,5 (in H O) CFM m³/h 8
6 Series 8000 N 80 x 80 x 38 mm Technology AC fans with external rotor shaded-pole motor. Impedance protected against overloading. Metal fan housing and impeller. Air exhaust over struts. Rotational direction CW looking at rotor. Electrical connection via leads. Stripped and tinned ends. Fan housing with ground lug for screw M4 x 8 (TORX). Mass: 490 g. DC Axial Fans DC Radial Fans Type m 3 /h CFM V Hz db(a) Bel / Watt min - C Hours Hours N / / N / / N / / N / / N / / N / / N / / N / / Fan Type Lead Wires 8830 N 8800 N 8550 N 8500 N 30 mm long AWG 8, TR N 30 mm long AWG 8, TR N 8506 N 30 mm long AWG 8850 N 4 mm long AWG 8, TR 64 Specials AC Axial Fans ACmaxx Axial Fans 0,05 0,0 0,5 0,0 (in H O) AC Radial Fans CFM m³/h 9 Accessories
7 Series 8000 TA 76 Ø x 37 mm AC fans with external rotor shaded-pole motor. Impedance protected against overloading. Impeller and mounting bracket of metal. Air intake over mounting bracket. Rotational direction CW looking at rotor. Electrical connection via leads. Stripped and tinned ends. Mass: 370 g ,5 35 ø75,8 0 3,7 0 R4 +0 0,3 +0, Type m 3 /h CFM V Hz db(a) / Watt min - C Hours Hours 8880 TA / / TA / / TA / / TA / / TA / / TA / / TA / / TA / / The air flow and noise level of fans without external housing depends on the installation conditions. The stated air flow and noise has been measured with an orifice 76.5 mm Ø at a distance of approx. 7 mm from the mounting bracket. Under exceptionally favourable mounting conditions, the air flow of fan series 8000 A is achievable. The noise in the optimal operating range can only be measured for these fans in a specific application. Fan Type Lead Wires 8880 TA 8850 TA 8830 TA 8800 TA 35 mm long AWG 8, TR TA 8500 TA 35 mm long AWG 8, TR TA 8506 TA 35 mm long AWG
8 Series 8000 TV 76 Ø x 37 mm Technology AC fans with external rotor shaded-pole motor. Impedance protected against overloading. Impeller and mounting bracket of metal. Air exhaust over struts. Rotational direction CW looking at rotor. Electrical connection via leads. Stripped and tinned ends. Mass: 370 g. DC Axial Fans DC Radial Fans Type m 3 /h CFM V Hz db(a) / Watt min - C Hours Hours 8880 TV / / TV / / TV / / TV / / TV / / TV / / TV / / TV / / The air flow and noise level of fans without external housing depends on the installation conditions. The stated air flow and noise has been measured with an orifice 76.5 mm Ø at a distance of approx. 7 mm from the mounting bracket. Under exceptionally favourable mounting conditions, the air flow of fan series 8000 N is achievable. The noise in the optimal operating range can only be measured for these fans in a specific application. Fan Type Lead Wires 8880 TV 8850 TV 8830 TV 8800 TV 35 mm long AWG 8, TR TV 8500 TV 35 mm long AWG 8, TR TV 8506 TV 35 mm long AWG 8 Specials ø75,8 0,3 0 +0,5 3,7 0 R4 +0, ACmaxx Axial Fans + 6 AC Radial Fans AC Axial Fans 90 Accessories
9 Series x 9 x 5 mm AC fans with internal rotor shaded-pole motor. Impedance protected against overloading. Metal fan housing, impeller of mineral-reinforced plastic PA. Air exhaust over struts. Rotational direction CCW looking at rotor. Electrical connection via flat pins.8 x 0.5 mm. Fan housing with ground lug for screw M4. Mass: 80 g. Type m 3 /h CFM V Hz db(a) Bel / Watt min - C Hours Hours 3950 L / / L / / M / / M / / / / / / L / / L / / M / / M / / / / / / ,05 0,0 0,5 0,0 (in H O) CFM m³/h
10 Series x 9 x 38 mm Technology AC fans with external rotor shaded-pole motor. Impedance protected against overloading. Metal fan housing and impeller. Air exhaust over struts. Rotational direction CW looking at rotor. Electrical connection via leads. Stripped and tinned ends. Fan housing with ground lug and screw M4 x 8 (TORX). Mass: 40 g. DC Axial Fans DC Radial Fans Type m 3 /h CFM V Hz db(a) Bel / Watt min - C Hours Hours / / / / / / / / / / / / / / / / / / / / / / / / Specials ACmaxx Axial Fans Fan Type Lead Wires With Sleeve bearings 30 mm long AWG 8, TR 64 With Ball bearings 30 mm long AWG 8 AC Axial Fans 0,05 0,0 0,5 0, 0,5 (in H O) AC Radial Fans CFM m³/h 3 Accessories
11 Series x 9 x 5 mm AC fans with external rotor shaded-pole motor. Protected against overloading by thermal cutout. Metal fan housing and impeller. Air exhaust over struts. Rotational direction CCW looking at rotor. Electrical connection via flat pins.8 x 0.5 mm. Fan housing with ground lug and screw M4 x 8 (TORX). Mass: 30 g Type m 3 /h CFM V Hz db(a) Bel / Watt min - C Hours Hours 9956 L / / M / / / / / / L / / M / / / / / / ,05 0,0 0,5 (in H O) CFM m³/h 4
12 Series 00 N 9 x 9 x 38 mm Technology AC fans with external rotor shaded-pole motor. Impedance protected against overloading. Metal fan housing and impeller Air intake over struts. Rotational direction CW looking at rotor. Types 4890 N and 48 N air exhaust over struts. Electrical connection via flat pins 3.0 x 0.5 mm. Also available: Models with mounting bosses and single leads. Fan housing with ground lug for screw M 4 and UNC. Mass: 550 g. DC Axial Fans at Tmax DC Radial Fans Type m 3 /h CFM V Hz db(a) Bel / Watt min - C Hours Hours 4890 N / / N* / / N* / / N* / / N / / N / / N / / N* / / N* / / N* / / N / / N / / Specials ACmaxx Axial Fans , 0, 0,3 (in H O) * Fan with 3 blades , 0, 0,3 (in H O) CFM m³/h Hz AC Axial Fans AC Radial Fans CFM m³/h 50 Hz 5 Accessories
13 Series 00 Z 9 x 9 x 38 mm AC fans with external rotor shaded-pole motor. Impedance protected against overloading. Metal fan housing and impeller. Air exhaust over struts. Rotational direction CW looking at rotor. Electrical connection via flat pins.8 x 0.5 mm. Also available: Models with mounting bosses and single leads. Fan housing with ground lug and screw M4 x 8 (TORX). Mass: 5 g Type m 3 /h CFM V Hz db(a) Bel / Watt min - C Hours Hours 4850 Z / / Z / / Z / / Z / / Z / / Z / / Z / / Z / / Z / / Z / / Z / / Z / / ,05 0,0 0,5 0,0 0,5 (in H O) CFM m³/h 6
14 Series 40 TA 3 Ø x 37 mm Technology AC fans with external rotor shaded-pole motor. Impedance protected against overloading. Impeller and mounting bracket of metal. Air intake over mounting bracket. Rotational direction CW looking at rotor. Electrical connection via leads. Stripped and tinned ends. Mass: 430 g. DC Axial Fans DC Radial Fans Type m 3 /h CFM V Hz db(a) / Watt min - C Hours Hours 4650 TA / / TA / / TA / / TA / / Specials The air flow and noise level of fans without external housing depends on the installation conditions. The stated air flow and noise has been measured with an orifice 09 mm Ø at a distance of approx. 7 mm from the mounting bracket. Under exceptionally favourable mounting conditions, the air flow of fan series 40 N is achievable. The noise in the optimal operating range can only be measured for these fans in a specific application. Fan Type Lead Wires 4650 TA 40 TA AWG, TR TA 46 TA AWG R4 0,5 +0, , +0, ø,5 +0,3 ACmaxx Axial Fans 4,3 0,5 + AC Axial Fans AC Radial Fans 90 7 Accessories
15 Series 40 TZ 08 Ø x 37 mm AC fans with external rotor shaded-pole motor. Impedance protected against overloading. Impeller and mounting bracket of metal. Air exhaust over struts. Rotational direction CW looking at rotor. Electrical connection via leads. Stripped and tinned ends. Mass: 430 g. 6 R4 0,5 +0, , 0, + ø08 0,3 + Type m 3 /h CFM V Hz db(a) / Watt min - C Hours Hours 4650 TZ / / TZ / / TZ / / TZ / / The air flow and noise level of fans without external housing depends on the installation conditions. The stated air flow and noise has been measured with an orifice 09 mm Ø at a distance of approx. 7 mm from the mounting bracket. Under exceptionally favourable mounting conditions, the air flow of fan series 00 Z is achievable. The noise in the optimal operating range can only be measured for these fans in a specific application. Fan Type Lead Wires 4650 TZ 40 TZ AWG, TR TZ 46 TZ AWG 8 4,3 0,
16 Series x 7 x 38 mm Technology AC fans with internal rotor shaded-pole motor. Impedance protected against overloading. Metal fan housing and impeller of fibreglass reinforced plastic PA. Air exhaust over struts. Rotational direction CCW looking at rotor. Electrical connection via flat pins.8 x 0.8 mm. Fan housing with ground lug and screw M4 x 6. Mass: 570 g. DC Axial Fans DC Radial Fans Type m 3 /h CFM V Hz db(a) Bel / Watt min - C Hours Hours / / / / / / / / / / / / ,05 0,0 0,5 0,0 0,5 (in H O) 3 4 AC Axial Fans ACmaxx Axial Fans Specials AC Radial Fans CFM m³/h 9 Accessories
17 Series x 35 x 38 mm AC fans with external rotor shaded-pole motor. Protected against overloading by thermal cutout. Metal fan housing and impeller. Air exhaust over struts. Rotational direction CCW looking at rotor. Electrical connection via flat pins.8 x 0.5 mm. Fan housing with ground lug and screw M4 x 8 (TORX). Mass: 800 g Type m 3 /h CFM V Hz db(a) Bel / Watt min - C Hours Hours 5656 S / / S / / , 0, 0,3 (in H O) CFM m³/h 30
18 Series x 7 x 38 mm Technology AC fans with external rotor capacitor motor. Protected against overloading by integrated thermal cutout. Metal fan housing and impeller. Air exhaust over struts. Rotational direction CCW looking at rotor. Electrical connection via flat pins.8 x 0.5 mm. Fan housing with ground lug and screw M4 x 6. Mass: 900 g. DC Axial Fans DC Radial Fans Type m 3 /h CFM V Hz db(a) Bel / Watt min - C Hours Hours 7056 ES / / ES / / Specials 0 80 Minimum ambient temperature -5 C, admissible for a short time at -30 C; without reaching dew point. 0, 0, 0,3 0,4 0,5 0,6 (in H O) AC Radial Fans AC Axial Fans ACmaxx Axial Fans CFM m³/h 3 Accessories
19 Series Ø x 55 mm AC fans with external rotor shaded-pole motor. Protected against overloading by integrated thermal cutout. Metal fan housing and impeller. Air exhaust over struts. Rotational direction CCW looking at rotor. Electrical connection via leads. Stripped and tinned ends. Fan housing with ground lug and screw M4 x 6. Mass: 000 g Type m 3 /h CFM V Hz db(a) Bel / Watt min - C Hours Hours 7855 ES / / ES / / ES / / ES / / 500 Minimum ambient temperature -5 C, admissible for a short time at -30 C; without reaching dew point. 0, 0, 0,3 0,4 0,5 (in H O) CFM m³/h 3
20 Series Ø x 55 mm Technology AC fans with external rotor shaded-pole motor. Protected against overloading by integrated thermal cutout. Metal fan housing and impeller. Air intake over struts. Rotational direction CCW looking at rotor. Electrical connection via leads. Stripped and tinned ends. Fan housing with ground lug and screw M4 x 6. Mass: 000 g. DC Axial Fans DC Radial Fans Type m 3 /h CFM V Hz db(a) Bel / Watt min - C Hours Hours 7450 ES / / ES / / Specials , 0, 0,3 0,4 (in H O) 00 Minimum ambient temperature -5 C, admissible for a short time at -30 C; without reaching dew point. AC Radial Fans AC Axial Fans ACmaxx Axial Fans CFM m³/h 33 Accessories
21 Series 00 7 Ø x 5 mm AC fans with external rotor capacitor motor. Protected against overloading by integrated thermal cutout. Metal fan housing and impeller. Air exhaust over struts. Rotational direction CCW looking at rotor. Electrical connection via flat pins.8 x 0.5 mm. Fan housing with ground lug and screw M4 x 6. Mass: 000 g. Type m 3 /h CFM V Hz db(a) Bel / Watt min - C Hours Hours 58 ES / / ES / / ES / / ES / / Minimum ambient temperature -5 C, admissible for a short time at -30 C; without reaching dew point , 0, 0,3 0,4 0,5 0,6 (in H O) CFM m³/h 34
22 W** 00 Ø 5 x 5 x 80 mm Technology External-single-phase motor.* External-current motor.** Motor protection: TOP wired internally. Material: Wall ring die-cast aluminium, seven blades sheet steel. Blades and rotor coated in black. Direction of air flow V, exhaustover struts. Direction of rotation: counter-clockwise, seen on rotor. Electrical connection: Terminal strips (operating capacitor connected). Continuous operation (S). Insulation class: F Mass: 000 g. DC Axial Fans DC Radial Fans Type m 3 /h CFM V Hz db(a) Bel / Watt min - C Hours Hours WE00-HK86-0* / / WE00-HK38-0* / / 000 W4S00-HK04-0** / / Specials [] ,05 0, 0,5 0,0 (in H O) ACmaxx Axial Fans Hz [CFM] [m³/h] AC Axial Fans [] , 0, 0,3 0,4 0,5 0,6 (in H O) AC Radial Fans [CFM] Hz m³/h Hz 35 Accessories
23 AC Diagonal Fans W*08 Ø 3 x 80 mm External-single-phase motor.* External-current motor.** Material: wall ring die-cast aluminium, five blades plastic PA. Rotor coated in black. Motor protection: Without TOP**; TOP wired internally*. Direction of air flow V, exhaustover struts. Direction of rotation: counter-clockwise, seen on rotor. Electrical connection: Terminal strips (operating capacitor connected). Continuous operation (S). Insulation class: F Mass: 800 g. Type m 3 /h CFM V Hz db(a) / Watt min - C Hours Hours WE 08-BA86-0* / / WE 08-BA0-0* / / WD 08-BA0-0** / / Y / n P LpA Typ [Hz] [min - ] [W] [dba] WD 08-BA 50 ➀ ❶ ➀ ➋ ➀ ➌ ➀ ➍ ➀ ➎ 7 67 ➀ ➏ ➀ ➐ ➀ ➑ WE 08-BA 50 ➀ ❶ ➀ ➋ ➀ ➌ ➀ ➍ ➀ ➎ ➀ ➏ ➀ ➐ ➀ ➑ , 0, 0,3 0,4 0,5 (in H O) CFM m³/h 36
24 WE x 80 x 80 mm Technology External single-phase motor. Motor protection: TOP wired internally. Material: Wall ring die-cast aluminium, seven blades sheet steel. Blades and rotor coated in black. Direction of air flow V, exhaustover struts. Direction of rotation: counter-clockwise, seen on rotor. Electrical connection: Terminal strips (operating capacitor connected). Continuous operation (S). Insulation class: F Mass: 000 g. DC Axial Fans DC Radial Fans Type m 3 /h CFM V Hz db(a) Bel / Watt min - C Hours Hours WE 50-HL / / ACmaxx Axial Fans Specials [] ,4 0,5 (in H O) 0, 0,3 3 AC Axial Fans AC Radial Fans 0 0, [CFM] Hz m³/h Hz 37 Accessories
25 AC Radial Fans Series RL 90 x x 37 mm AC radial blower with external rotor shaded-pole motor. Impedance protected against overloading. Spiral housing and blower wheel of fibreglass-reinforced plastic. Housing base of galvanised steel plate. Air exhaust radial, through housing port. Rotational direction CW looking at rotor. Electrical connection via leads. Stripped and tinned ends. Mass: 680 g. Type m 3 /h CFM V Hz Bel / Watt min - C Hours Hours RL 90-8/ / / RL 90-8/ / / RL 90-8/ / / RL 90-8/ / / Fan Type Lead Wires RL 90-8/50 RL 90-8/00 AWG 8, TR 3 RL 90-8/56 RL 90-8/06 AWG 0, 0, 0,3 0,4 (in H O) CFM m³/h 38
26 AC Radial Fans Series RG x 35 x 38 mm Technology AC radial blower with external rotor shaded-pole motor. Impedance protected against overloading. Spiral housing and blower wheel of fibreglass-reinforced plastic. Housing base of galvanised steel plate. Air exhaust radial, through housing port. Rotational direction CW looking at rotor. Electrical connection via leads AWG. Stripped and tinned ends. Mass: 5 g. DC Axial Fans DC Radial Fans Type Type m 3 /h m 3 /h CFM CFM V DCV Hz Hz db(a) Bel Bel / / Watt Watt min min - - C C Hours Hours Hours Hours RG 90-8/ / / RG 90-8/ / / RG 90-8/ / / RG 90-8/ / / AC Axial Fans ACmaxx Axial Fans Specials AC Radial Fans 0, 0, 0,3 0,4 (in H O) CFM m³/h 39 Accessories
27 AC Radial Fans Series RG 5 80 x 80 x mm AC radial blower with external rotor shaded-pole motor. Impedance protected against overloading. Spiral housing and blower wheel of fibreglass-reinforced plastic. Housing base of galvanised steel plate. Air exhaust radial, through housing port. Rotational direction CW looking at rotor. Electrical connection via leads AWG. Stripped and tinned ends. Mass: 850 g. Type m 3 /h CFM V Hz Bel / Watt min - C Hours Hours RG 5-9/ / / RG 5-9/ / / , 0,4 0,6 (in H O) CFM 0 80 m³/h
28 AC Radial Fans Series RG 0 x 0 x 56 mm Technology AC radial blower with external rotor shaded-pole motor. Thermal contactor as protection against thermal overloading. Spiral housing and blower wheel of fibreglass-reinforced plastic. Housing base of galvanised steel plate. Air exhaust radial, through housing port. Rotational direction CCW looking at rotor. Electrical connection via leads AWG 8. Stripped and tinned ends. Mass:.7 kg. DC Axial Fans DC Fans Radial Type Type m 3 /h m 3 /h CFM CFM V DCV Hz Hz db(a) Bel Bel / / Watt Watt min min - - C C Hours Hours Hours Hours RG -8/56S / / RG -8/06S / / 500 Specials AC Axial Fans ACmaxx Axial Fans ,4 0,8, (in H O) AC Radial Fans CFM m³/h 4 Accessories
29 AC Radial Fans Seriess RER 5 38 Ø x mm AC radial blower with external rotor shaded-pole motor. Impedance protected against overloading. Blower wheel of fibreglass-reinforced plastic, with steel plate reinforced. Air exhaust radial. Rotational direction CW looking at rotor. Electrical connection via leads AWG. Stripped and tinned ends. Mass: 500 g. Type m 3 /h CFM V Hz Bel / Watt min - C Hours Hours RER 5-9/ / / 500 RER 5-9/ / / , 0, 0,3 (in H O) The air flow and noise level of fans without external housing depend on the installation conditions. The stated air flow and noise levels have been measured under the following conditions: Centrifugal fan mounted on a base plate 0 x 0 mm. Cover plate 0 x 0 mm with an air-inlet of Ø 86 mm, concentric to the blower wheel CFM m³/h 4
30 AC Radial Fans Series RER 76 Ø x 54 mm Technology AC radial blower with external rotor shaded-pole motor. Impedance protected against overloading. Blower wheel of fibreglass-reinforced plastic, with steel plate reinforced. Air exhaust radial. Rotational direction CCW looking at rotor. Electrical connection via leads AWG 8. Stripped and tinned ends. Mass: 000 g. DC Axial Fans y DC Radial Fans TypType m 3 /h m 3 /h CFM CFM V DCV Hz Hz db(a) Bel Bel / / Watt Watt min min - - C C Hours Hours Hours Hours RER -8/56S / / RER -8/06S / / Specials ACmaxx Axial Fans AC Axial Fans AC Radial Fans The air flow and noise level of fans without external housing depend on the installation conditions. The stated air flow and noise levels have been measured under the following conditions: Centrifugal fan mounted on a base plate x mm. Cover plate x mm with an air-inlet of Ø 00 mm, concentric to the blower wheel. 0, 0,4 0,6 0,8 (in H O) CFM m³/h 43 Accessories
AC axial fans, AC diagonal fans
fans, C diagonal fans Technology ccessories EC-SYSTEMS ESM General information K series Q-motor EC axial EC axial fans series fans fans Ø 130 - Ø 250 14 C diagonal fans Ø 208 20 13 Contacts fans Ø 130
More informationInformation. DC axial fans. DC axial fans. DC axial fan overview 27 DC axial fan / DC diagonal fan
Information DC axial fan overview 27 DC axial fan / DC diagonal fan 31 25 Representatives Accessories AC centrifugal fans AC axial fans ACmaxx / EC fans DC fans - specials DC centrifugal fans Technical
More informationEnergy-saving motors (ESM)
Energy-saving motors (ESM) Technology Accessories EC-SYSTEMS ESM General information K series Q-motor EC axial EC axial fans A series fans Energy-saving motors (ESM) 316 Air performance curves 3 Energy-saving
More informationThe new fan generation S-Force
The new fan generation S-Force S-Force The Ultimate Performer The strongest team in the league The S-Force series is composed of five smaller series with sizes from 80 to 172 mm. Each is the world champion
More informationHammond Electronic Rack Packaging
Hammond Electronic Rack Packaging 195 1 4-20 spring loaded nuts and 0.62 round head slotted bolts and washers for C channels. Description Net Price l 1421S Pkg. of 4 $14.82 CABLE ORGANIZING RING PANELS
More informationCompact Fans for AC and DC. Catalogue 2007
Compact Fans for AC and DC Catalogue 007 RoHS Trendsetter in Fan Technology Uncompromising quality made by ebm-papst Among the best. Trendsetting with innovative technologies. Listening to customers needs.
More informationAC axial fan. blades with special design (K series) with guard grille for full nozzle
SE6-EC-5 ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 798 8- Fax +9 798 8- info@de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen County court Stuttgart
More informationAC centrifugal fan. backward curved
RE-AB6- ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 798 8- Fax +9 798 8- info@de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen County court Stuttgart
More informationAC axial fan. sickled blades (S series), single inlet Wall ring with guard grille
WE5-CO5-66 ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 798 8- Fax +9 798 8- info@de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen County court Stuttgart
More informationAC centrifugal fan with housing (small flange)
DE-HT- ebm-papst Mulfingen GmbH & Co. KG Bachmühle Mulfingen Phone: + - Fax: + - www.ebmpapst.com info@de.ebmpapst.com Nominal data Type Motor DE-HT- ME-EC Phase ~ ~ Nominal voltage [V] Frequency [Hz]
More informationAC centrifugal module - RadiCal
KE5-RA- ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 798 8- Fax +9 798 8- info@de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen Amtsgericht (court of
More informationCross-flow Fans. TFD/FFD Series
Cross-flow Fans TFD/FFD Series Cross flow fans are particularly indicated for uses where, in limited space, high air volume is required with low noise and regular air-flow. The FF-FFD series provides an
More informationAC centrifugal fan. backward curved
RE8-CB8- ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 798 8- Fax +9 798 8- info@de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen County court Stuttgart
More informationCross-Flow Fans. TF/FF Series
Cross-Flow Fans TF/FF Series Cross flow fans are particularly indicated for uses where, in limited space, high air volume is required with low noise and regular air-flow. The FF-FFD series provides an
More informationAC centrifugal fan. forward-curved, single-intake with housing (flange)
GE8-AA- ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 798 8- Fax +9 798 8- info@de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen Amtsgericht (court of
More informationAC centrifugal fan. forward curved, dual inlet with housing (flange)
DE-AM7- ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 798 8- Fax +9 798 8- info@de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen County court Stuttgart
More informationAC centrifugal fan. forward curved, dual inlet with housing (flange)
ebm-papst Mulfingen GmbH & Co. KG Bachmühle 2 D-74673 Mulfingen Phone: +49(0)7938/81-0 Fax: +49(0)7938/81-110 info1@de.ebmpapst.com www.ebmpapst.com Nominal data Type Motor D2E133-AM47-23 M2E068-DF Phase
More informationProduct Data Sheet ACi 4420 HHR
ACi 4420 HHR INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 4 3 Operating Data... 5 3.1 Operating Data - Electrical Interface - Input... 5 3.2 Electrical Operating Data... 5
More informationProduct Data Sheet ACi 4420 MLR
ACi 4420 MLR INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 4 3 Operating Data... 5 3.1 Operating Data - Electrical Interface - Input... 5 3.2 Electrical Operating Data... 5
More informationAC centrifugal fan. forward curved, dual inlet with housing (without flange)
DE-DM7- ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 798 8- Fax +9 798 8- info@de.ebmpapst.com www.ebmpapst.com Nominal data Type Motor DE-DM7- ME68-DF Phase ~ ~ Nominal voltage
More informationStandard and value-added costech frame fans with a comprehensive range of accessories
Standard and value-added costech frame fans with a comprehensive range of accessories Technical specifications A and D frame fans drawings D blowers drawings numbering system description A 12 B 23 H T
More informationAC axial fan. sickled blades (S series) with full square nozzle
WD5-GA-9 ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 798 8- Fax +9 798 8- info@de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen County court Stuttgart
More informationPerformance. Sound Levels. Impellers. Motors. Accessories
EuroSeries (ESP) Die cast aluminium impellers Fully speed controllable Air Volumes up to 13.89m 3 /s Sizes 250 to 1000 dia protected to IP54 Operating Temperatures from -40 C up to +70 C Insulation Class
More informationAC axial fan. sickled blades (S series) Wall ring with guard grille
W4E3-DN2-39 ebm-papst Mulfingen GmbH & Co. KG Bachmühle 2 D-74673 Mulfingen Phone +49 7938 81- Fax +49 7938 81-11 info1@de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen County
More informationAC axial fan. sickled blades (S series) with guard grille for full nozzle
SE-P8-6 ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 798 8- Fax +9 798 8- info@de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen County court Stuttgart
More informationCooling Fans MU Series 119 mm 38 mm Thick ( 4.69 in. 1. in. Thick) Ambient Temperature: 1 + C (+14 +14 F) Operating Voltage Range: ±1% Materials Frame: Die Cast Aluminum Blades: Polycarbonate (Flammability
More informationPSC Thermal Solutions. size 273 x 220 x202mm
Impeller: PP UL94V-O Reinforced Plastic(f1) Connector:AMP 350781-1 Motor: Capacitor-Run Inductionexternal rotor Motor Insulation:Class B T.P.F. Safety: UL. CE.CUL Operation Temperature:-10 ~+70 size 273
More informationAC centrifugal fan. forward-curved, dual-intake with housing (without flange)
DE-AM7-65 ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 798 8- Fax +9 798 8- info@de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen Amtsgericht (court of
More informationAC axial fan. sickled blades (S series)
AE5-AL6- ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone: +9()798/8- Fax: +9()798/8- info@de.ebmpapst.com www.ebmpapst.com Nominal data Type Motor AE5-AL6- ME68-CF Phase ~ ~ Nominal voltage
More informationMB Series AC Centrifugal Blowers
MB Series AC Centrifugal Blowers Impeller Diameter 6.3 in. dia. ( 16 mm) SAFETY STD. AC INPUT Specifications c Materials Motor Case: Casing: Impeller: Aluminum Voltage Frequency Current Input Power Max.
More informationStandard and value-added costech frame fans with a comprehensive range of accessories
Standard and value-added costech frame fans with a comprehensive range of accessories Technical specifications A and D frame fans drawings drawing 1 drawing 2 drawing 3 drawing 4 drawing 5 drawing 6 drawing
More informationAC axial fan. sickled blades (S series)
ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone: +9()798/8- Fax: +9()798/8- info@de.ebmpapst.com www.ebmpapst.com Nominal data Type Motor ME68-CF Phase ~ ~ Nominal voltage V Frequency
More informationProduct Data Sheet 3214 J/2H3F-191
The engineer's choice 3214 J/2H3F-191 INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical
More informationAVC FAN. AC Axial Fans. AC Axial Fans
AC Axial Fans AC Axial Fans 63 AS SERIES 80*80*38 mm Motor:Shaded pole AC motor. Frame & Imeller:Al Die-casting & PBT plastic. AS8038-V1H-_ B S 110 50/60 14/11 AS8038-V2H-_ B S 230 50/60 14/11 2450/2950
More informationAC centrifugal fan - RadiCal
RE5-RB6- ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 798 8- Fax +9 798 8- info@de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen County court Stuttgart
More informationAC axial fan. Limited partnership Headquarters Mulfingen County court Stuttgart HRA
S4D45-AP3- ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-74673 Mulfingen Phone +49 7938 8- Fax +49 7938 8- info@de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen County court
More informationProduct Data Sheet 4118 N/ The engineer's choice
The engineer's choice 4118 N/12-190 INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Electrical Operating Data... 4 3.2 Operating Data - Electrical
More informationCAS 460 2T 7.5. Impeller size motor poles 2=3500 r/min. 60 Hz. Installed power
CAS CAS: High pressure, single inlet centrifugal fans with sheet steel casing and impeller : High pressure, single inlet centrifugal fans with sheet steel casing and impeller, fitted with acoustic attenuators
More informationVORTICENT C E RANGE Centrifugal fans
NEW VORTICENT C E RANGE Centrifugal fans Suitable for domestic, commercial and industrial applications: kitchens, bathrooms, offices, laboratories, factories, shops, laundromats, models, restaurants, bars,
More informationDC Dual Inlet Centrifugal Blowers
DC Dual Inlet Centrifugal Blowers 85 to 656 CFM Brushless DC Dual Inlet Centrifugal Blowers.5..9.6 4 6 8 35 3 5 5.3 3 5 3 4 5 6 Curve Ref. Rota- CFM Wgt. Temp. Number Part Number Volts Watts Flange tion*
More informationProduct Data Sheet 4184 N/17X. The engineer's choice
Product Data Sheet 4184 N/17X The engineer's choice 4184 N/17X INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Electrical Operating Data... 4 3.2 Electrical
More informationAC axial fan. straight blades (A series) with full round nozzle
WD-CA- ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 798 8- Fax +9 798 8- info@de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen County court Stuttgart
More informationProduct Data Sheet 632 NU-006
The engineer's choice 632 NU-006 INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical
More informationMegaBox Product-specific information
MegaBox Product-specific information Application Noise-encapsulating centrifugal fans with retractable motor impeller unit and motor located outside the air flow Suitable for rough operating conditions
More informationIN-LINE DUCT FANS MIXVENT-TD Fan Systems
IN-LINE DUCT FANS MIXVENT-TD Fan Systems NEW TD-EXTRACTOR KIT (see page 175) MIXVENT TD / MIXVENT TD-T MIXVENT TDx2 ACCESSORIES Description Range Construction The MIXVENT system has been designed to compliment
More informationTF037C MICRO BLOWERS FEATURES STANDARD SPECIFICATIONS
FEATURES Aerodynamic bearings Compact / Light weight High static pressures Low vibration Long life due to aerodynamic bearings without heat dependence Two type available with or without mounting bracket
More informationTerminal Box Are to IP54, as standard, protected against dust and water from any angle allowing outside applications.
EuroSeries (ESR) Cowl & base moulded from recyclable polymeric material All sizes resistant to UV light Sizes 250 to 1000 dia are protected to IP54 Optional backdraught shutters and bird guard (250-630mm)
More informationProduct Data Sheet 8314 HR-197
The engineer's choice 8314 HR-197 INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical
More informationProduct Data Sheet 3214 JH3-195
3214 JH3-195 INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 5 3.1 Operating Data - Electrical Interface - Input... 5 3.2 Electrical Operating Data... 6
More informationProduct Data Sheet 624 NR. The engineer's choice
Product Data Sheet 624 NR Product Data Sheet 624 NR The engineer's choice Product Data Sheet 624 NR 624 NR INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data...
More informationIt is SPG. 21C Standard of The World Geared Motor. Product descriptions
21C Standard of The World Geared Motor It isspg All of the four major electric home appliance manufacturers ; GE, Whirlpool, Electrolux, have chosen SPG Motor. SPG which produces the world best quality
More informationSeries VENTS KSK. Centrifugal kitchen fan in sound-insulated casing with air flow up to 8138 m 3 /h
SOUND-INSULATED KITCHEN FAN Series device. The impeller is mounted on the motor shaft and is balanced statically and dynamically. The motor has F class motor winding insulation and ingress protection rating.
More informationProduct Data Sheet DV5214 NU
The engineer's choice DV5214 NU INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical Operating
More informationAxial-flow Fan AFC. Model numbering system AF C / T. Accessories Three phase. Power rate 1.
xial-flow Fan FC Construction xial fan designed for installation in a ducted system. Casing of rolled and electro-welded steel sheet, powder coated RL5. Impeller in polypropylene. Casing in acid-proof
More informationProduct Data Sheet 4184 NXHH
The engineer's choice 4184 NXHH INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 5 3.1 Operating Data - Electrical Interface - Input... 5 3.2 Electrical Operating
More informationEnergy-saving axial fans. A solution specifically designed for unit cooler applications. The engineer s choice. 10-Position rotary switch
Energy-saving axial fans A solution specifically designed for unit cooler applications. The engineer s choice 0-Position rotary switch New SG05 series designed for unit cooler applications EC axial fans
More information4314/17T. Product Data Sheet INDEX
4314/17T INDEX 1 General... 2 2 Mechanics... 2 2.1 General... 2 2.2 Connections... 2 3 Operating Data... 2 3.1 Operating Data - Electrical Interface - Input... 3 3.2 Electrical Operating Data... 4 3.3
More informationProduct Data Sheet 4184 NGX
The engineer's choice 4184 NGX INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical Operating
More informationProduct Data Sheet 4184 NXHH
The engineer's choice 4184 NXHH INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical Operating
More informationBrushless DC Axial Fans
Brushless DC Axial Fans General Specifications Material: Body PBT UL 9V- Fan PBT UL 9V- Insulation Class E Approvals UL, cul Recognized E89 Box Count: x 8 pieces x pieces 9 x pieces 8 x pieces x pieces
More informationDynamically-balanced impellers with extremely robust cores CMP T 5.5
Medium pressure, single inlet centrifugal fans with sheet steel casing and impeller Fan: Sheet steel casing. Forward-curved impeller made of galvanised sheet steel. 38-2M model casing in cast aluminium.
More informationSabre Plate Mounted Sickle Fans (VSP)
Sabre Plate Mounted Sickle Fans (VSP) Swept impeller with Aerofoil blades, winglets and serrated trailing edge for optimum performance One shot die cast impeller, dynamically balanced for smoother operation
More informationProduct Data Sheet 8412 NHU-519
The engineer's choice 8412 NHU-519 INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical
More informationMODEL TD-MIXVENT INLINE MIXED FLOW DUCT FAN
MODEL FEATURES Exhaust air up to 2,630 CFM with static pressure capabilities to 1 w.g. Mixed flow impeller for excellent air flow to pressure performance ratio Direct connection, two-speed motor Ideal
More informationProduct Data Sheet 614 N/2HH-169 The engineer's choice
The engineer's choice 614 N/2HH-169 INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Electrical Operating Data... 4 3.2 Operating Data - Electrical
More informationProduct Data Sheet 8412 N/ The engineer's choice
The engineer's choice 8412 N/12-252 INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Electrical Operating Data... 4 3.2 Electrical Interface - Output...
More informationAC axial fans S series, Ø 500
axial fans, Ø 500 Material: Guard grille: Steel, phosphated and coated in black plastic Wall ring: Sheet steel, pre-galvanised and coated in black plastic lades: Sheet aluminium Rotor: ncased in aluminium
More informationTSAT: Single inlet, belt-driven centrifugal fans fitted with electric motors. CJTSA: Ventilation units with a forward-curved impeller.
TSA TSAT CJTSA TSA: Single inlet, belt-driven centrifugal fans with shaft outlet and forward-curved impeller. TSAT: Single inlet, belt-driven centrifugal fans fitted with electric motors, a set of pulleys
More informationCONTENTS. Page. Adjustable Axial Pitch Flow Fans 3. Dimensions 4. AP056 Performance Curves 5. AP056 Sound Performance 6. AP063 Performance Curves 7
CONTENTS Page Adjustable Axial Pitch Flow Fans 3 Dimensions 4 AP056 Performance Curves 5 AP056 Sound Performance 6 AP063 Performance Curves 7 AP063 Sound Performance 8 AP071Performance Curves 9 AP071 Sound
More informationUnobox units with backward curved centrifugal impellers
Unobox Fans Unobox units with backward curved centrifugal impellers Type Code UNO 67-450 -4 E W Unobox Box size 50=500mm ; 67=670mm 80=800mm ; 102=1020mm Impeller diameter Number of poles D - Three Phase
More informationProduct Data Sheet 4414/2H
The engineer's choice 4414/2H INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical Operating
More informationBifurcated Case Axial Fans (BIFA)
Bifurcated Case Axial Fans (BIFA) Sizes 250 to 1000 dia Motors protected to IP55 Motor insulation Class F Maximum ambient temperature 200 C Speed controllable via transformer or inverter (when the ambient
More informationIN-LINE MIXED FLOW DUCT FANS TD-MIXVENT Series
Range of low profile in-line mixed flow duct fans manufactured in tough reinforced plastic (from 16 to 8 models) or with metal casing steel finished in a tough epoxy-polyester paint coating (from 1 to
More informationIN-LINE MIXED FLOW DUCT FANS MIXVENT-TD Fan Systems
IN-LINE MIXED FLOW DUCT FANS MIXVENT-TD Fan Systems MIXVENT TD / MIXVENT TD-T MIXVENT TDx2 ACCESSORIES Description Range Construction The MIXVENT system has been designed to compliment the MIXVENT-TD range
More informationAC axial fan. sickled blades (S series) with guard grille for full nozzle
SD-BH8- ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 798 8- Fax +9 798 8- info@de.ebmpapst.com www.ebmpapst.com Limited partnership Headquarters Mulfingen County court Stuttgart
More informationContents. Fans. Page. Make Farnell-Newark InOne your first choice - search over 300,000 products at
Farnell Page 709 Date: 18-08-06 time:16:26 Contents Page Accessories 7 Axial Flow - Low Vltage dc 714 Axial Flow - Mains ac 710 Backward Curved 720 Blowers 721 Fan Speed Controllers 723 Flatpack 720 High
More informationVent-Axia Sabre Sickle Roof Fans (VSR)
Vent-Axia Sabre Sickle Roof Fans (VSR) Features and Benefits High performance roof sickle fan Fully assembled cowl. Optional backdraught shutters and birdguard Moulded from recyclable polymeric material,
More informationAxial fans 400ºC/2h and 300ºC/2h With soundproofed box. Extraction units with axial fans to work inside fire danger zones.
CJTHT Axial fans 400ºC/2h and 300ºC/2h With soundproofed box Extraction units with axial fans to work inside fire danger zones. Fan: Sheet steel long casing fan. Galvanised sheet steel structure with thermal
More informationSeries VENTS OVK. Low pressure axial fans in the steel casing with the air. for wall mounting.
AXIAL FANS Series VENTS OV Series VENTS OVK Series VENTS Low pressure axial fans in the steel casing with the air capacity up to 11900 m 3 /h for wall mounting. Low pressure axial fans in the steel casing
More informationproduct specification
4414 ML Customer specification: No Version: 1.0 Created: 16.09.2011 INDEX 1 General... 2 2 Mechanics... 2 2.1 GENERAL... 2 2.2 MOTOR... 2 2.3 CONNECTIONS... 3 3 Operating Data... 4 3.1 OPERATING DATA -
More informationProduct Data Sheet 8414 NGH
The engineer's choice 8414 NGH INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical Operating
More informationAC Commercial Fans Edition. ErP ready
AC Commercial Fans 213 Edition ErP ready AC Commercial Fans Axair Fans UK Ltd / 1782 34943 About Axair Fans UK Axair is an independent industrial fan manufacturer and distributor. What we offer : Application
More informationCSXRT: Single inlet, belt-driven centrifugal fans fitted with electric motors. CJSXR: Ventilation units with a backward-curved impeller
CSXR CSXRT CJSXR CSXR: Belt-driven single inlet centrifugal fans with shaft outlet and backward-curved impeller CSXRT: Belt-driven single inlet centrifugal fans fitted with electric motors, a set of pulleys
More informationIn-Line Fans. Roof Fans. Fans ATEX. Centrifugal Fans. Chip Extractors. Domestic Fans. Accessories. Electric Diagrams. General Information.
In-Line Fans xial-flow Fans Wall Versions xial-flow Fans Cased Versions Roof Fans Fans TEX Centrifugal Fans VISP/VSP Centrifugal Fans Side Channel lowers Chip Extractors COMPCT 44 TCx, TCTx FC 54 FC-V
More information400ºC/2h centrifugal roof fans with horizontal or vertical air outlet CHT 200 4T BS. Installed capacity
400ºC/2h centrifugal roof fans with horizontal or vertical air outlet : 400ºC/2h centrifugal roof fans with horizontal air outlet, hood in aluminium : 400ºC/2h centrifugal roof fans with vertical air outlet,
More informationVENTS KSB K2. Series. Inline centrifugal fans in heat- and sound-insulated casing with air flow up to 7000 m 3 /h SOUND-INSULATED FANS
SOUND-INSULATED FANS Series Inline centrifugal fans in heat- and sound-insulated casing with air flow up to 7 m 3 /h Purpose KSB fan design allows to use them in supply and exhaust ventilation systems
More informationProduct Data Sheet DV4118 N
The engineer's choice DV4118 N INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 5 3.1 Operating Data - Electrical Interface - Input... 5 3.2 Electrical Operating
More informationAXIAL FAN WITH EXTERNAL ROTOR MOTOR
XIL FN ITH EXTERNL ROTOR MOTOR 1. YF series axial fans are external rotor motors. These motors have characteristics of compact structure, convenient installation and high efficiency etc. 2. YF series external
More informationMODEL TD-MIXVENT INLINE MIXED FLOW DUCT FAN
MODEL TD-MIXVENT INLINE MIXED FLOW DUCT FAN MODEL FEATURES Exhaust air up to 2,630 CFM with static pressure capabilities to 1 w.g. Mixed flow impeller for excellent air flow to pressure performance ratio
More informationMAJAX-2 GENERAL SPECIFICATION
MAJAX-2 GENERAL SPECIFICATION Majax-2 axial flow fans are manufactured in diameters ranging from 315mm to 2000mm (available in 2250mm on request), and incorporate manually adjustable pitch aluminium bladed
More informationGMP-Type. Key Features: Integrated Motor-Pump Units
Integrated Motor-Pump Units GMP-Type Key Features: Direct coupling between motor and pump Rotation: Right (viewed from shaft end) Electric motor mounting type: special B3-B14 (IEC 34-7) Rated Voltage:
More informationCONTRA ROTATING CASED AXIAL FANS TCBBx2 / TCBTx2 Series
Range of cylindrical cased axial fans fitted with aluminium impellers and manufactured from high grade rolled galvanised steel and protected against corrosion by cataforesis primer and black polyester
More informationSabre Sickle Fan Assisted Roof Cowls (VSR)
Sabre Sickle Fan Assisted Roof Cowls (VSR) Swept impeller with Aerofoil blades, winglets and serrated trailing edge for optimum performance Fully assembled cowl, separate plate axial fan Optional backdraught
More informationA6C A5C-B6C B5C B5H A6C A5C B6C B5C B5H. Model. Up to kw. Power. Up to V. Voltages. Model IP55. Frame Pole 2, 4, 6, 8 and 10
A6C A5C-B6C B5C B5H Model Power Voltages Model IP55 A6C A5C B6C B5C B5H Up to 2.400 kw Up to 11.000 V LV A6C - B6C - A5C - B5C MV B5H Frame 71 560 Pole 2, 4, 6, 8 and 10 Cooling IC 411 ( IC 416 optional)
More informationIN-LINE MIXED FLOW DUCT FANS TD-MIXVENT Series
Range of low profile in-line mixed flow duct fans manufactured in tough reinforced plastic (from to models) or with metal casing steel finished in a tough epoxy-polyester paint coating (from to models).
More informationSquare Mixed Flow Fans (MFQ)
Square Mixed Flow Fans (MFQ) Features and Benefits Motors protected to IP44 Motor insulation Class B Maximum operating temperature +40 C Standard Thermal Overload Protection Sizes 400 to 500 3 phase are
More informationDATA SHEET. Three Phase Induction Motor - Squirrel Cage. Customer : Product code : : W22 NEMA Premium Efficiency Three-Phase
DATA SHEET Frame Output Poles Frequency Rated voltage Rated current L. R. Amperes LRC No load current Rated speed Slip Rated torque Locked rotor torque Breakdown torque Insulation class Service factor
More informationGeneral Purpose Three Phase Motors TEFC (IP55) High Efficiency. Standard Features
TM WEG W21 Severe Duty motors meet the most demanding severe duty application requirements. These TEFC motors are all cast iron construction, with enclosures rated IP55 to handle wet and dirty environments.
More informationGreenTech. FlatPak. EC Technology AXIAL. RadiCal. ACi4400 IP68. S-Panther. Blowers. RadiPac. Motors FANS IMPELLERS COMPACT.
RadiPac CENTRIFUGAL Custom Assembly GreenTech AXIAL RadiCal S-Panther COMPACT Motors ACi4400 FANS IP68 EC Technology FlatPak Blowers IMPELLERS ebm-papst air moving solutions available from Sager Electronics
More informationIN-LINE CENTRIFUGAL DUCT FANS VT Series
IN-LINE CENTRIFUGAL DUCT FANS VT Series DESCRIPTION The VT series of circular in-line duct centrifugal fans consists of model variations within nominal model sizes of,,,,, and mm respectively. The VT range
More information