KEYSTONE FIGURE 9 BUTTERFLY VALVE
|
|
|
- Joel Barber
- 6 years ago
- Views:
Transcription
1 A resilient seated butterfly valve for general purpose applications FEATURES Bubble-tight shut-off at full pressure rating (PTFE lined configuration is drop tight). The seat and the disc are the only two valve parts in contact with the medium. Superior design for abrasive and erosive media. Famous Keystone dovetail seat design. Very low pressure drop. Large number of material combinations available. Standardized actuator flange for easy operator interchangeability. Top bushing absorbs side thrust loads. Hub seal provided by preloaded contact between flatted seat surface and disc hub area for positive sealing at all disc positions. One-piece wafer thin disc stem gives the very minimum obstruction to flow. Field replaceable seat isolates the body and stem from the flow. Molded-in O-rings provides flange sealing and eliminates need for gaskets. GENERAL APPLICATION The ideal valve for dry bulk conveying, food and beverage processing, corrosive slurries and paperstock. TECHNICAL DATA Pressure (bar): 10* Temperature ( C): Sizes (DN): Flange acc.: PN 10 ANSI 150 Other flanges on request * For mirror polished/satin finished disc the max. differential pressure is 6 bar for sizes DN valves.emerson.com 2017 Emerson. All rights reserved. VCTDS EN 15/08
2 G F 1 E C Q A H YY B Mounting holes 7 D VALVE DIMENSIONS (mm) Mass Size A B C D E F G H YY Q (kg) Part Name 1. Bushing 2. Shaft seal 3. Upper body 4. Seat 5. Disc-stem 6. Lower body 7. Body screws NOTES 1. Valve size shown is the DN 100; other sizes show different configurations. For information see separate data sheets. 2. Q is the disc chordal dimension at face of valve for disc clearance into pipe fitting or equipment. 2
3 DN DN / DN DN 350 / DN 500 ACTUATOR FLANGE DIMENSIONS (mm) Shaft dimensions Actuator flange dimensions Keysize No. of Size F G K J width x height E P PCD Hole ø holes x x x x x x
4 VALVE DATA K v VALUES Disc opening * NOTE * Rubber covered disc 1. Rated K v = the volume of water in m 3 /hr that will pass through a given valve opening at a pressure drop of 1 bar. MAXIMUM ALLOWABLE SHAFT TORQUES (Nm) Shaft mat * * * For mirror polished/satin finish disc, contact factory. SIZING TORQUES (Nm) ΔP in bar I* II* III* * Application I, II, III NOTES 1. Application I Water, seawater, lubricating types of hydrocarbons. Temp.: 0-80 C; Valve opens at least once a month. Application II All other liquid applications and lubricating gasses. Application III Non lubricating and dry media. 2. The charted maximum sizing operating torque is the sum of all friction and resistance for opening and closing of the disc against the indicated pressure differential. 3. The effect of dynamic torque is not considered in tabulation. 4. In sizing operators it is not necessary to include safety-factors. DYNAMIC TORQUE FACTORS F T FOR METRIC UNITS Disc opening NOTES 1. Dynamic operating torque formula: T D = F T x ΔP T D = Dynamic torque (Nm) ΔP = Pressure drop across disc at desired disc-opening (bar) F T = Dynamic torque factor (see table) 2. The dynamic torque includes all frictional resistances. 3. The dynamic torque is tending to close the disc. 4. The charted maximum allowable torques are only applicable for standard type valves. 4
5 VALVE DATA AND MATERIAL SELECTION ACTUATOR SELECTION Actuator type Figure Remark Handle F401 Leverlock F410 Gear F422 - Composite Body Disc Shaft Seat Trim no. Sizes (mm) Cast iron Stainless steel Stainless steel EPDM NBR White NBR PTFE/EPDM Cast iron Stainless steel (satin finished) Stainless steel EPDM NBR White NBR PTFE/EPDM Cast iron Stainless steel (mirror polished) Stainless steel EPDM NBR White NBR PTFE/EPDM Cast iron EPDM covered Stainless steel EPDM Cast iron PTFE covered Stainless steel PTFE/EPDM Cast iron Titanium Titanium EPDM NBR PTFE/EPDM PRESSURE - TEMPERATURE DIAGRAM Disc Body Size range Valve function Temperature in C Seat material material material DN (mm) Wafer/end of line Notes EPDM all except: all all W 10 Bar 1 SS (MP/SF) all W 6 Bar 2 NBR and White NBR all except: all all W 10 Bar 4 SS (MP/SF) all W 6 Bar 5 PTFE/EPDM all except: all all W 10 Bar 2 Bar 6 SS (MP/SF) all W 6 Bar 1 Bar 7 PRESSURE - TEMPERATURE DIAGRAM Note Trims
6 6
Keystone Butterfly Valve Figure 9
A resilient seated butterfly valve for general purpose applications Features Bubble-tight shut-off at full pressure rating (PTFE lined configuration is drop tight). The seat and the disc are the only two
Keystone Figure 9 Butterfly Valve
A resilient seated butterfly valve for general purpose applications Features Bubble-tight shut-off at full pressure rating (PTFE lined configuration is drop tight). The seat and the disc are the only two
BrewSeal butterfly valves Wafer and lugged
Wafer and lugged KEYSTONE Resilient seated butterfly valves DN40-DN800 wafer and lugged versions, optimized for the food and beverage industry. Features Top bushing absorbs actuator side thrust loads.
KEYSTONE OPTISEAL WAFER AND LUGGED
A resilient seated butterfly valve for general purpose applications FEATURES GENERAL APPLICATION Food and beverage processing, dry bulk conveying, paper mills, slurry handling etc. Grease or silicone free
Keystone Double flanged butterfly valve Figure 55
Double flanged valve design for services in the water treatment industry Features General application Waterwork industries where a double flanged valve is required. Fire fighting systems. Sea water applications.
Keystone CompoSeal Resilient Seated Butterfly Valves Wafer style
Wafer style Resilient seated butterfly valves with valve body and disc in high engineered composite material providing excellent internal and external chemical resistance Features General application Since
Keystone CompoSeal Resilient Seated Butterfly Valves Wafer style Sizes DN PN 10/16
Wafer style Sizes DN -3 PN /1 Resilient seated butterfly valves with valve body and disc in high engineered composite material providing excellent internal and external chemical resistance. Features Patented
Keystone resilient seated butterfly valves Figure 221 and 222
Figure 221 and 222 An economical bonded resilient seated butterfly valve for bi-directional and end-of-line service F221 Wafer style valve F222 Lugged style valve Features Bubble tight shut-off at full
Keystone CompoSeal Resilient Seated Butterfly Valves Wafer style
Wafer style Resilient seated butterfly valves with valve body and disc in high engineered composite material providing excellent internal and external chemical resistance. Features General application
VALVES & CONTROLS KEYSTONE BUTTERFLY VALVES RESILIENT SEATED SERIES 61, 14" TO 24" 61W - Wafer style and 61L - Lugged style FEATURES
VALVES & CONTROLS KEYSTONE BUTTERFLY VALVES RESILIENT SEATED 61W - Wafer style and 61L - Lugged style FEATURES Rounded polished disc edge gives full concentric sealing, lower torques, longer seat life
Keystone Figure 990 and 920 Resilient Seated Butterfly Valves
A split body thin disc valve for high flow and modulating service Figure 990 - Wafer body design Figure 920 - Lugged body design Features General application Figure 990 and 920 valves are used when modulating
KEYSTONE PN16 DOUBLE FLANGED BUTTERFLY VALVE FIGURE 631
The F631 PN16 is a bi-directional, double flanged, resilient seated butterfly valve FEATURES Approved to AS/NZS 4020, making the F631 suitable for use in potable water applications. Type tested in accordance
61W - Wafer style resilient seated butterfly valves 61L - Lugged style resilient seated butterfly valves
61W - Wafer style resilient seated butterfly valves 61L - Lugged style resilient seated butterfly valves Features Rounded polished disc edge gives full concentric sealing, lower torques, longer seat life
The ParaSeal range features a proven disc shaft and seat arrangement, to be used in high pressure and high velocity applications.
Butterfly Valve ParaSeal range The ParaSeal range features a proven disc shaft and seat arrangement, to be used in high pressure and high velocity applications. Features The field replaceable seat fully
BUTTERFLY VALVE 17 SERIES Gearbox
DN H1 H2 H3 BUTTERFLY VALVE 17 SERIES Gearbox FIGURE: 17234ER: 17234BR: 17234VR: Seat in EPDM, with gearbox Seat in Buna, with gearbox Seat in Viton, with gearbox B ØR L DIMENSIONS: (mm) DN L B XR H1 H2
The Keystone Series GR is a heavy duty industrial resilient seated butterfly valve aimed at general purpose applications.
The Keystone Series GR is a heavy duty industrial resilient seated butterfly valve aimed at general purpose applications. Features Wafer and lugged body design with face-to-face dimension, according to
Technical data Pressure (bar) : 10 Temperature ( C) : Sizes (mm) : Flange accommodation : DIN PN 10/(16)
50 300 mm wafer and lugged lined butterfly valves - Coilspring shaft sealing A PTFE lined solution according ISO 5752/5 short (EN 558-1/T5) with various corrosion resistant disc materials to satisfy demanding
KEYSTONE SERIES GR RESILIENT SEATED BUTTERFLY VALVES GRW/GRL
KEYSTONE SERIES GR RESILIENT SETED BUTTERFLY VLVES GRW/GRL heavy duty industrial resilient seated butterfly valve GRW - Wafer body design GRL - Lugged body design FETURES GENERL PPLICTION Water, air, dry
KEYSTONE SERIES GR RESILIENT SEATED BUTTERFLY VALVES GRW/GRL
heavy duty industrial resilient seated butterfly valve GRW - Wafer body design GRL - Lugged body design FETURES GENERL PPLICTION Water, air, dry bulk conveying etc. These valves are for any service where
1-20 (25mm-500mm) SERIES 20/21 Wafer/Lug SANITARY AND CHEMICAL / RESILIENT SEATED BUTTERFLY VALVES. The High Performance Company
BUTTERFLY VALVES SANITARY AND CHEMICAL / RESILIENT SEATED SERIES 20/21 Wafer/Lug 1-20 (25mm-500mm) The High Performance Company SERIES 20 1-20 (25mm-500mm) Bray Controls is proud to offer a high quality
25mm-500mm (1"- 20") SERIES 20/21 Wafer/Lug BUTTERFLY VALVES SANITARY AND CHEMICAL / RESILIENT SEATED. The High Performance Company
BUTTERFLY VALVES SANITARY AND CHEMICAL / RESILIENT SEATED SERIES 20/21 Wafer/Lug 25mm-500mm (1"- 20") The High Performance Company SERIES 20 25mm 500mm (1" 20") Bray Controls is proud to offer a high quality
BUTTERFLY VALVE VF-7 Series
BUTTERFLY VALVE VF-7 Series CENTRIC, RUBBER SEATED LEVER GEAR PNEUMATIC - ELECTRIC OPERATED ALLOWABLE PRESSURE DN 40 300mm : 16 bar DN 350 1200mm : 10 bar INVESTMENT CASTING STAINLESS STEEL BODY 2 12 (50mm
2-20 (50mm-500mm) SERIES 30/31 Wafer/Lug RESILIENT SEATED BUTTERFLY VALVES. The High Performance Company
BUTTERFLY VALVES RESILIENT SEATED SERIES 30/31 Wafer/Lug 2-20 (50mm-500mm) The High Performance Company SERIES 30/31 2-20 (50mm-500mm) Bray Controls is proud to offer a high quality line of butterfly valves
KEYSTONE BUTTERFLY VALVE PARASEAL RANGE
The ParaSeal range features a proven disc, shaft and seat arrangement designed for use in high pressure and high velocity applications FEATURES GENERAL APPLICATION Water, food and beverage processing,
WAFER BUTTERFLY VALVES
WAFER BUTTERFLY VALVES Actuator flange accomodate all type of operators; handle, gear, electric and pneumatic actuator Strong precision key gives positive attachment for manual lever or actuator. Shaft
KEYSTONE BUTTERFLY VALVE PARASEAL RANGE
The ParaSeal range features a proven disc, shaft and seat arrangement designed for use in high pressure and high velocity applications FEATURES GENERAL APPLICATION Water, food and beverage processing,
GRW/GRL Sizes NPS 2-36
KEYSTONE The Keystone Series GR is a heavy duty industrial resilient seated butterfly valve aimed at general purpose applications. Features Wafer and lugged body design with face-toface dimension, according
Keystone Butterfly valve ParaSeal range
The ParaSeal range features a proven disc, shaft and seat arrangement designed for use in high pressure and high velocity applications Features General application Water, food and beverage processing,
RESILIENT SEATED BUTTERFLY VALVES. Howell Valve & Automation. Toll Free: Howellvalve.com
RESILIENT SEATED BUTTERFLY VALVES Howell Valve & Automation Toll Free: 1-888-469-3557 Howellvalve.com TABLE OF CONTENTS Description Page Index 2 Resilient Standard Features 3 ST Boot Series with BUNA-N
Cover Page - Butterfly Valves Ordering Information Design Features, 2 to 12 Design Features, 2 to 12 (continued)
DESCRIPTION Cover Page - Butterfly Vs Ordering Information Design Features, 2 to 2 Design Features, 2 to 2 (continued) Design Features, 2 to 2 (continued) Design Features, 4 to 4 CV Chart, 2 to 4 Torque
KEYSTONE SERIES 60 BUTTERFLY VALVE
60W wafer style resilient seated butterfly valve 60L lug style resilient seated butterfly valve Cartridge seat design FATURS GNRAL APPLICATION Ideally suited for many industrial applications such as food
BUTTERFLY VALVE 27 SERIES Pneumatic actuator - El-O-Matic
C D E FIGURE: PD: pneumatic actuator, double acting PE: pneumatic actuator, spring return PEO: pneumatic actuator, spring return, normally open BUTTERFLY VALVE 27 SERIES Pneumatic actuator - El-O-Matic
2"- 20" (50mm-500mm) SERIES 30/31 Wafer/Lug RESILIENT SEATED BUTTERFLY VALVES CELEBRATING. The High Performance Company
BUTTERFLY VALVES RESILIENT SEATED SERIES 30/31 Wafer/Lug 2"- 20" (50mm-500mm) CELEBRATING Y E A R S The High Performance Company SERIES 30 2" 20" (50mm 500mm) Bray Controls is proud to offer a high quality
2"- 20" (50mm-500mm) series 30/31 Wafer/Lug. butterfly valves. resilient seated. The High Performance Company
butterfly valves resilient seated series 30/31 Wafer/Lug 2"- 20" (50mm-500mm) The High Performance Company SERIES 30 2" 20" (50mm 500mm) Bray Controls is proud to offer a high quality line of butterfly
Keystone Butterfly valve ParaSeal range
The ParaSeal range features a proven disc, shaft and seat arrangement designed for use in high pressure and high velocity applications Features General application Water, food and beverage processing,
2"- 20" (50mm-500mm) series 30/31 Wafer/Lug. butterfly valves. resilient seated. The High Performance Company
butterfly valves resilient seated series 30/31 Wafer/Lug 2"- 20" (50mm-500mm) The High Performance Company SERIES 30 2" 20" (50mm 500mm) Bray Controls is proud to offer a high quality line of butterfly
KEYSTONE SERIES GR RESILIENT SEATED BUTTERFLY VALVES GRW/GRL (ISO)
heavy duty industrial resilient seated butterfly valve FETURES GENERL PPLICTION Water, air, dry bulk conveying etc. These valves are for any service where a drop-tight shut-off with maximum flow area is
HOPPER SHAPE KNIFE GATE VALVE
HOPPER SHAPE KNIFE GATE VALVE The C model knife gate is a uni-directional wafer valve designed for industrial bulk handling service applications (powdered and granular products). makes it ideal for use
F627 DOUBL DOUBLE EC E E C C E C N E TRI R C I BUTTER E F R LY L VA Y V LV L ES E BS EN 593
F627DOUBLE ECCENTRC BUTTERFLY VALVES BS EN 93 The Keystone Figure 627 PQ is a Bi-directional, double eccentric, resilient seated butterfly valve, available in double flanged and wafer configurations. Features:
KEYSTONE SERIES GR RESILIENT SEATED BUTTERFLY VALVES GRW/GRL (ISO)
heavy duty industrial resilient seated butterfly valve FETURES GENERL PPLICTION Water, air, dry bulk conveying etc. These valves are for any service where a drop-tight shut-off with maximum flow area is
WAFER STYLE KNIFE GATE VALVE
WAFER STYLE KNIFE GATE VALVE The model knife gate is an uni-directional wafer valve designed for general industrial service applications. The design of the body and seat assures non-clogging shut off on
Technical changes kept in reserve THROUGH CONDUIT KNIFE GATE VALVE
Technical changes kept in reserve THROUGH CONDUIT KNIFE GATE VALVE The B model knife gate is a bi-directional wafer valve designed for media with high consistency. The double seat design assures a non-clogging
WAFER STYLE KNIFE GATE VALVE
11 WAFER STYLE KNIFE GATE VALVE The model knife gate is an uni-directional wafer valve designed for general industrial service applications. The design of the body and seat assures non-clogging shut off
SERIES. The Ultraflo Transport Line Resilient Seated Butterfly Valves: Specifically Designed for use in the Bulk Trailer Industry.
The Ultraflo Transport Line Resilient Seated Butterfly Valves: 2-12 Specifically Designed for use in the Bulk Trailer Industry 390 SERIES 400 SuperioR Performance STRONGER Construction Ultraflo proudly
Technical changes kept in reserve WAFER STYLE KNIFE GATE VALVE. DN 50 to DN 250: 10 kg/cm² DN 300 to DN 400: 6 kg/cm²
WAFER STYLE KNIFE GATE VALVE The A model knife gate is an uni-directional wafer valve designed for general industrial service applications. The design of the body and seat assures non-clogging shut off
BUTTERFLY VALVE ST BUTTERFLY VALVE VALVES - 31
BUTTERFLY VALVE ST BUTTERFLY VALVE REVREV 6.2 6.2 / Nov. / Nov. 2017 2017 VALVES - 31 High Performance Butterfly Valve STHW STHL Size : 2 ~ 24 Type: Wafer, Lug Pressure Rating: Class 150, 300 Body Material:
KNIFE GATE VALVE Product Ref. : KG02W/KG02L
General Description Model KG02 is a bidirectional knife gate valve suitable for most industrial application cases. With one piece body design, it combines robust and economy giving best cost effective
SERIES 2200 Replaceable Seat Butterfly Valves
SERIES 2200 Replaceable Seat Butterfly Valves Publication S2200-101 Issue 04/18 Rev. A Design Characteristics Multiple Seat Options VSI offers various seat options including EPDM, NBR, Viton, and others
Size : Ends : Min Temperature : Max Temperature : Materials : Cast iron body
Size : Ends : Min Temperature : Max Temperature : DN 32/40 to DN 300 Between flanges PN10/16 and ISO PN20 ANSI150-10 C + 80 C Max Pressure : 16 Bars Specifications : Long neck for isolation Stainless steel
Transportation Products
Transportation Products Butterfly Valves Hopper Tees Actuators Accessories A Name You ve Trusted for Years... Resilient Seated Butterfly Valves 400 & 480 Series 1 Piece Body Design This economical, resilient
Installation Operation Maintenance. LSSN Butterfly Valve AGA Approved 50MM - 150MM. QAD#IM6055.REVA
LSSN Butterfly Valve Installation Operation Maintenance Licence Number: 5326 www.challengervalves.com.au 1 Index 1. INTRODUCTION 1.1 Design Features 3 1.2 Flange and Pipe Compatibility 4 1.3 Operating
Section 18 Butterfly Valves
Section 18 Butterfly Valves Edition 2 261 [18] BUTTERFLY VALVES Butterfly Valves Resilient seat Butterfly Valves are used in a wide range of Industries including HVAC, Gas, Petrochemical, Pulp & Paper,
RESILIENT SEATED BUTTERFLY VALVES
DESIGN FEATURES APPLICATIONS: HVAC Chemical/Petrochemical Processing Food and Beverage Industry Power and Utilities Pulp and Paper Industry Stem Configuration: Gives positive attachment for handles or
Materials : Ductile iron body EN GJS
Size : Ends : Min Temperature : Max Temperature : DN 40 to 600 mm Between flanges PN10/16-10 C + 110 C Max Pressure : 16 Bars up to DN300, 10 bars over Specifications : Long neck for isolation Ductile
L15 HEAVY DUTY KNIFE GATE VALVE STANDARD PARTS LIST
L15 HEAVY DUTY KNIFE GATE VALVE The L15 model knife gate is a uni-directional lug type valve designed according to MSS-SP-81 and TAPPI TIS 405-8 for industrial service applications. The design of the body
WAFER STYLE KNIFE GATE VALVE
WAFER STYLE KNIFE GATE VALVE The EX(SER.10) model knife gate is an uni-directional wafer valve designed for general industrial service applications. The design of the body and seat assures non-clogging
Series 8500 Grayline Butterfly Valves
Series 8500 Grayline Butterfly Valves Features State-of-the-Art Manufacturing: Valves are produced using state-of-the-art manufacturing equipment. Each valve is tested to 110% of rated working pressure
Materials : Ductile iron body EN GJS
Size : Ends : Min Temperature : Max Temperature : DN 40 to 600 mm Between flanges PN16 up to DN300-10 C + 110 C Max Pressure : 16 Bars up to DN300, 10 bars over Specifications : Long neck for isolation
DOUBLE-ECCENTRIC BUTTERFLY VALVES TYPE L32.7
Application Double-eccentric butterfly valves are industrial valves, which are designed to fully open or close the passage of the working medium flowing through a pipeline. They can also be used for flow-control
Keystone knife gate valves Figure OS1700
Bi-directional zero leakage ASME Class 150 rated knife gate valve. Designed for the rigors of high pressure slurry and oil sands applications Features General application The OS1700 has many features to
HOPPER SHAPE KNIFE GATE VALVE
HOPPER SHAPE KNIFE GATE VALVE The model knife gate is a uni-directional wafer valve designed for industrial bulk handling service applications (powdered and granular products). The special design of the
KEYSTONE FIGURES 310/312 K-LOK BUTTERFLY VALVES
310 - Wafer high performance butterfly valve 312 - Lugged high performance butterfly valve FEATURES GENERAL APPLICATION High performance applications such as steam, chill water, water, utility lines, gasoline,
SERIES 2100 Resilient Seated Butterfly Valves
SERIES 2100 Resilient Seated Butterfly Valves Publication S2100-101 Issue 06/16 Rev. C Design Characteristics Applications Commercial Heating & Air Conditioning Waste Water & Water Treatment Sea Water
ALC-3 BUTTERFLY VALVES NOMINAL PRESSURE NOMINAL SIZE MATERIALS CONNECTIONS DESIGN. ANSI Class PN DN
BUTTERFLY VALVES ALC-3 NOMINAL PRESSURE ANSI Class 150-600 PN 10-100 NOMINAL 2-80 DN 50-2000 MATERIALS Cast Iron Carbon Steel Low Alloy Steel CONNECTIONS Wafer Lugged Flanged Butt Weld DESIGN Eccentric
Wafer, Semi Lug, Lug and Flanged Type
Year : Wafer, Semi Lug, Lug and Flanged Type Page 1 Year : Specification Description : GVC concentric rubber lined butterfly valves suitable for bi-directional flow and bubble tight shut-off at full rated
NAF-Torex butterfly valves DN , Size 3-28, PN 10-40, ANSI Class 150, 300
NAF-Torex butterfly valves DN 80-700, Size 3-28, PN 10-40, ANSI Class 150, 300 Fk 41.42(18)GB 11.04 Primary characteristics NAF-Torex, High-Performance butterfly valve is available with either metal-to-metal
RUBBER SLEEVE KNIFE GATE VALVE
RUBBER SLEEVE KNIFE GATE VALVE The model knife gate is a wafer valve designed for a wide range of industrial applications. The double-seated design provides bi-directional shut off. The design of the valve
Transportation Valves
Transportation Valves A Name You ve Trusted for Years... 780 Series Butterfly Valves Features: Available in sizes 3 thru 6 One handle fits sizes 3 thru 6 Integrated 180º notch plate eliminates mounting
Materials : Ductile iron body EN GJS
Certificate 3.1 Size : Ends : Min Temperature : Max Temperature : DN 32 to 600 mm Between flanges PN10/16, Class 150 and JIS10K* - 10 C + 110 C Max Pressure : 16 Bars up to DN300 (10 bars over) Specifications
WAFER STYLE KNIFE GATE VALVE
MODEL WAFER STYLE KNIFE GATE VALVE The model knife gate is an uni-directional wafer valve designed for general industrial service applications. The design of the body and seat assures non-clogging shut
KEYSTONE K-LOK SERIES H HIGH PERFORMANCE BUTTERFLY VALVES
Series H1 ASME Class 150 / 25 bar Series H2 ASME Class 300 / 50 bar FEATURES GENERAL APPLICATIONS Airport refueling Hydrocarbon processing Chlorine Chemical processing Purified gas Steam and vacuum services
BUTTERFLY VALVES + UM ELECTRIC ACTUATOR
1150-1183 BUTTERFLY VALVES + UM ELECTRIC ACTUATOR FEATURES 1150-1183 butterfly valves are intended for the automatic opening /closing of very diverse fluid pipes. The valve body is made of GS cast iron.
Size : Ends : Min Temperature : Max Temperature : Materials : Cast iron body
Size : Ends : Min Temperature : Max Temperature : DN 32/40 to DN 1200 Between flanges PN10/16, ANSI150 up to DN600-10 C + 110 C ( 130 C temporarily ) Max Pressure : 16 Bars up to DN300 Specifications :
NAF-Torex butterfly valves DN , Size 3-28, PN 10-40, ANSI Class 150, 300
NAF-Torex butterfly valves DN 80-700, Size 3-28, PN 10-40, ANSI Class 150, 300 Fk 41.42(17)GB 08.01 Primary characteristics NAF-Torex, High-Performance butterfl y valve is available with either metal-to-metal
Materials : Ductile iron body EN GJS
Certificate 3.1 Size : Ends : Min Temperature : Max Temperature : DN 40 to 600 mm Between flanges PN10/16-10 C + 110 C Max Pressure : 16 Bars up to DN300, 10 bars over Specifications : Long neck for isolation
Bonded Liner Butterfly Valve Double Flanged Type Series 150
Year : Page 1 Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve enter b.v. Year : General Product Information Design Technical Data Description : GV
Size : Ends : Min Temperature : Max Temperature : Materials : PVC-U body
Size : Ends : Min Temperature : Max Temperature : DN 65 to 200 mm Between flanges PN10/16 0 C + 40 C Max Pressure : 10 Bars up to DN125 Specifications : 7 positions lever Wafer type ISO 5211 mounting pad
Series 240 Type 3351 Pneumatic On/off Valve
Series 240 Type 3351 Pneumatic On/off Valve Application Shut-off valve with tight shut-off for liquids, gases and vapors according to DIN or ANSI standards Valve size DN 15 to 100 NPS ½ to 4 Pressure rating
Wafer, Semi Lug, Lug and Flanged Type
Year : Wafer, Semi ug, ug and Flanged Type API 607 Fire Safe Page 1 Year : Description Specification : GVC double eccentric High Performance butterfly valves suitable for bi-directional flow and bubble
Concentric butterfly valves
Lug Between flanges PN10/16 1135 Lever Disc GGG40 nickel plated / Seat EPDM.../10: flanges PN10.../16: flanges PN16 DN 40 50 65 80 100 125 150 200/10 200/16 250/10 250/16 300/10 300/16 16 16 16 16 16 16
BI-DIRECTIONAL KNIFE GATE VALVES XD-PRE SERIES WITH D/A PNEUMATIC ACTUATOR
BI-DIRECTIONAL KNIFE GATE VALVES XD-PRE SERIES KGV XD-PRE SERIES FULLY LUGGED WITH RISING STEM & HANDWHEEL KGV XD-PRE SERIES FULLY LUGGED WITH D/A PNEUMATIC ACTUATOR KGV XD-PRE SERIES FULLY LUGGED WITH
Long Face to Face. Bonded Liner Butterfly Valve Mono Flanged Type (Long) Series 130. Document : S130 Revision : 3 Year : 2014
Year : Long Face to Face Page 1 Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve enter b.v. Year : General Product Information Technical Data Description
butterfly valves high performance TRIPLE OFFSET HP-TRI REV0
high performance EXECUTION 1st OFFSET 2nd OFFSET 3rd OFFSET The BELVEN-TRI series incorporate triple offset disc configuration. With this configuration the disc seal makes contact with body seat, only
ZWISCHENFLANSCH ABSPERRKLAPPE AK011
Size : Ends : Min Temperature : Max Temperature : DN 32/40 to DN 1200 Between flanges PN10/16, ANSI150 up to DN600-10 C + 110 C ( 130 C temporarily ) Max Pressure : 16 Bars up to DN300 Specifications :
These PFA and PTFE lined products offer a reliable solution in hazardous applications
These PFA and PTFE lined products offer a reliable solution in hazardous applications Features Check valves Heavy duty body in ductile iron GGG4.3 (ASTM A-395). Heavy duty PFA or PTFE lining. Borosilicate
Sealing Test Pressure (MPa)
TRIPLE ECCENTRIC BUTTERFLY VALVE Triple Eccentric Butterfly Valve provides a tight shut-off. This geometry ensures that the disc seal contacts the body seat only at the final shut-off position without
Mono Flanged Type Long Face to Face
Year : Mono Flanged Type Long Face to Face Page 1 Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve enter b.v. Year : General Product Information Technical
butterfly valves high performance Ruamcharoen Engineering And Supplies Ltp., Tel : Fax :
high performance EXECUTION OFFSET FROM CENTRE OF VALVE OFFSET FROM CENTRE OF SEAT VALVE CENTRE LINE SHAFT CENTRE LINE Valve body is solid, heavy duty. Seat Retainer construction allows Gasket conforming
BFV : 14 : 10 : 12 BUTTERFLY VALVE
BFV : 14 : 10 : 12 BUTTERFLY VALVE Looks Like Conventional Butterfly Valve... 2 FEATURES HIGHER Cv Larger disc for larger flow Improved profile of disc provides minimum Resistance to flow BOTTOM STEM Stem
Short Face to Face. Bonded Liner Butterfly Valve Mono Flanged Type (Short) Series 120. Document : S120 Revision : 2 Year : 2014
Year : Short Face to Face Page 1 Provided data is not contractual, data may be changed without notice. All rights reserved Global Valve enter b.v. Year : General Product Information Technical Data Description
Series 240 Pneumatic On-off Valve Type 3351
Series 240 Pneumatic On-off Valve Type 3351 Application Control valve with a tight shutoff of liquids, gases and steam in accordance with DIN or ANSI standards Nominal sizes DN 15 to 100 NPS ½ to 4 Nominal
PNEUMATIC ON OFF GLOBE VALVE
PNEUMATIC ON OFF GLOBE VALVE Model No. AGE0 SERIES s Bonnet -way globe valve, -way globe valve 1A(1/") ~ 00A(1") JIS 10K~K, ANSI 10#~900#, PN10~, etc. FF, RF, BW, SW Plain bonnet: -17 ~0 Extended bonnet:
Introduction. Resilient Seat Butterfly Valves. Valves D-207.
Introduction Resilient Seat Butterfly D-207 Resilient Seat Butterfly are now available in sizes up to 20-inches. Excellent for isolation applications, two-way and floating Butterfly provide 2-position
NAF-Setball ball sector valves DN , PN 10-40, ANSI Class
NAF-Setball ball sector valves DN 25-400, PN 10-40, ANSI Class 150-300 Fk 41.51(12)GB 4.98 Replaces Fk 41.51(1GB 12.97 Primary characteristics NAF-Setball is a ball sector valve with metal-to-metal or
butterfly valves Quality, Service A history of and Innovation
A history of Quality, Service and Innovation Now in its ninth decade, Conbraco Industries, Inc. is a leading manufacturer of flow control products for U.S. and international markets. The company s headquarters
Keystone Figures 310/312 K-LOK Butterfly Valves
310 - Wafer high performance butterfly valve 312 - Lugged high performance butterfly valve Features General Application High performance applications such as steam, chill water, water, utility lines, gasoline,
Pneumatic Shut-off Butterfly Valve Type 3335/BR 31a
Pneumatic Shut-off Butterfly Valve Type 3335/BR 31a Application Tight-closing butterfly valve for process engineering and plants with industrial requirements DN 50 to DN 300 2 to 12 Nominal pressure PN
MADE OF STAINLESS...
MADE OF STAINLESS... Size : Ends : Min Temperature : Max Temperature : DN 50 to 600 mm ( NPS 2" to 24" ) Between Class 150 (PN20) flanges 29 C + 210 C Max Pressure : 20 Bars Specifications : Double eccentric
Dura Water Wafer Butterfly Valve
Dura Water Wafer Butterfly Valve Specifications Recommended use Features Working Pressure The Dura butterfly valve is a soft sealing valve for installation with flanges drilled in accordance with AS 2129
Suggested Specifications
ISO 9001 Certified Suggested Specifications The Milliken criteria of quality, reliability, safety and value are embodied in the Millcentric Eccentric valve, setting higher standards for dependable performance