CX6150 CAT 6 Enhanced UTP System

Transcription

1 3933 US Route 11 Cortland, NY 1345 Telephone: (67) Facsimile: (67) July 7, 214 Berk-Tek, Nexans Company 132 White Oak Road New Holland, P Test report number Project number Leviton Network Solutions nd SE Bothell, W 9821 CX615 CT 6 Enhanced UTP System TEST: Electrical performance testing of a cabling configuration to the requirements of NSI/TI-568-C.2 for Category 6 channel. STNDRD USED: NSI/TI-568-C.29: Balanced Twisted-Pair Telecommunications Cabling and Components Standards, dated ugust 29 SECTION: 6.2: Channel transmission performance (6.2.1 to ) SMPLE DESCRIPTION: The client supplied a CX615 CT 6 Enhanced UTP System 4-connector test configuration as illustrated below. The samples were received on June 3, 214 and were production samples in undamaged condition. Component Id Manufacturer Part number 1 Leviton Equipment Cord, 3 m 6D56-1 2, 4 Leviton Patch Panel H24 3 Leviton Equipment Cord, 2 m 6D56-7 5, 7 Berk-Tek CMR Horizontal Cable LNmark-1 6 Leviton Consolidation Point 41B6-1F4 8 Leviton Workstation Jack / Faceplate 6111-R*6 9 Leviton Equipment Cord, 5 m 6D56-15 Page 1 of 2 This report is for the exclusive use of Intertek s and is provided pursuant to the agreement between Intertek and its. Intertek s responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the is authorized to permit copying or distribution of this report and then only in its entirety. ny use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only the sample tested. This report by itself does not imply that the material, product or service is or has ever been under an Intertek certification program. Intertek Testing Services N, Inc.

2 Berk-Tek Leviton Technologies Test report number July 7, 214 UTHORIZTION: The project was authorized by Mr. Eric J. Lawrence, representing Berk-Tek with signed quotation EQUIPMENT LIST: The following equipment was employed in conducting the tests. Equipment used Model number Control number Calibration date Calibration due date HP utomatic Cable Test System E37 2/26/214 2/26/215 DTE OF TEST: July 7, 214 TEST REPORT REVISION HISTORY: First Issue: July 7, 214 Original Document RESULTS: See appendix for the test results. CONCLUSION: The CX615 CT 6 Enhanced UTP System channel cabling configuration, as previously described and supplied by the client, was tested in accordance with the standard referred to on page 1, and did comply with the indicated applicable transmission requirements. The testing was performed at Intertek located in Cortland, New York. The procedures and requirements were taken from the standard referred to on page Reviewed and pproved By: ntoine Pelletier Engineer Global Cabling Products Testing ssociate Engineer Global Cabling Products Testing Page 2 of 2 Intertek Testing Services N, Inc.

3 Berk-Tek Leviton Technologies Test report number July 7, 214 Summary test results This appendix contains 5 pages. Intertek Testing Services N, Inc.

4 ification CX615 CT 6 Enhanced UTP Length(m) Limit Margin MHz ttenuation ttenuation Limit Margin : MHz Return Loss Return Loss Page 1

5 ification CX615 CT 6 Enhanced UTP Length(m) Limit Margin : MHz NEXT NEXT Limit Margin : 2459 MHz PSNEXT PSNEXT Page 2

6 ification CX615 CT 6 Enhanced UTP Length(m) Limit Margin : MHz CR CR Limit Margin : MHz PSCR PSCR Page 3

7 ification CX615 CT 6 Enhanced UTP Length(m) Limit Margin : MHz CR-F / ELFEXT CR-F / ELFEXT Limit Margin : MHz PSCR-F / PSELFEXT PSCR-F / PSELFEXT Page 4

8 ification CX615 CT 6 Enhanced UTP Length(m) TCL TCL ELTCTL ELTCTL Page 5