Product Submittals for Project
|
|
|
- Poppy Benson
- 5 years ago
- Views:
Transcription
1 Product Submittals for Project May 011-1
2 Couplings Figure 577 Light Weight Rigid Coupling For Fire Protection Pressure Rating and Listing / Approval information contact Tyco Fire Suppression & Building Products. Ductile Iron Housing Specifications ASTM A-536 Standard Specification for Ductile Iron Casting Grade Tensile Strength, minimum psi 65,000 (448 MPa) Yield Strength, minimum psi 45,000 (310 MPa) Elongation in (50mm), minimum 1% ASTM A-153 Standard Specification for Hot Dip Galvanizing Bolt/Nut Specifications Carbon steel oval neck bolts and nuts are heat treated and conform to the physical properties of ASTM A-183 with a minimum tensile strength of 110,000 psi (760 MPa). Bolts and nuts are zinc electroplated to ASTM B-633. Metric - conforming to ASTM F-568M Coatings Orange Non-Lead (Standard) Fire Brigade Red Non-Lead (Optional) Hot Dipped Zinc Galvanized (Optional) Gasket Specifications Grade A EPDMA, violet color code ambient to +150 F (+66 C) for fire protection systems. Not recommended for hot water systems. Tri-seal (Grade E EPDM), green color code for use in dry pipe or freezer systems. Prelubricated (Grade A EPDMA) Project: Date: Architect / Engineer: Contractor: Address: Notes: May Project Information: Phone: Technical Data Sheet: TFP1854 Date: March 011 Approval Stamp: Page 1 of
3 Couplings Figure 577 Light Weight Rigid Coupling (cont.) B C A FIGURE 577 GROOVED RIGID COUPLING 1-1 (DN5 TO DN) Nominal ANSI DN 1 DN5 1-1/4 DN3 1-1/ DN40 DN50-1/ DN65 DN65 3 DN80 4 DN100 DN15 5 DN15 DN150 6 DN150 8 DN00 10 DN50 1 DN Pipe Size O.D (33,4) (4,) (48,3).375 (60,3).875 (73,0) (76,) (88,9) (114,3) (139,7) (141,3) (165,1) 6.65 (168,3) 8.65 (19,1) (73,1) 0 (33,9) Max. Pressures psi (bar) (4,1) (4,1) (4,1) (4,1) (4,1) (4,1) (4,1) (0,7) (0,7) (0,7) (0,7) (0,7) (0,7) 175 (1,1) 175 (1,1) Max. End Load Lbs. (kn) 475 (,11) 757 (3,37) 99 (4,41) 1,551 (6,90),7 (10,11),474 (11,01) 3,367 (14,98) 4,771 (1,) 7,17 (31,71) 7,90 (3,43) 9,955 (44,8) 10,341 (46.00) 17,58 (77,97) 15,883 (70,7),343 (99,4) Max. * End Gap 0.15 (3,) 0.15 (3,) 0.15 (3,) 0.15 (3,) 0.15 (3,) 0.5 (6,4) 0.5 (6,4) Nominal Dimensions A 1.63 ().66 (68).90 (74) 3.38 (86) 3.88 (99) 4.00 (10) 4.50 (114) 5.70 (145) 6.80 (173) 6.86 (174) 7.80 (198) 8.47 (15) 10.5 (60) 1.50 (318) (368) B 3.9 (100) 4.40 (11) 4.66 (118) 5.0 (13) 5.64 (143) 5.78 (147) 6.33 (161) 7.50 (191) 8.75 () 8.8 (4) 9.75 (48) 9.88 (51) 1.78 (35) (419) (470) C 1.65 (4) 1.64 (4) 1.66 (4) 1.70 (43) (44) () (44) 1.83 (46).40 (61).56 (65).56 (65) Qty. Coupling Bolts Size** 3/8 x -1/4 3/8 x -1/4 3/8 x -1/4 3/8 x -1/4 3/8 x -1/4 3/8 x -1/4 3/8 x -1/4 M1 x 76 1/ x 3 M1 x 76 M1 x 76 1/ x 3 M1 x 76 5/8 x 3-1/4 3/4 x 4-3/4 M0 x 11 3/4 x 4-3/4 M0 x 11 Approx. Weight Lbs. (kg) 1. (0,55) 1.3 (0,59) 1.5 (0,68) 1.8 (0,8).0 (0,91).0 (0,91) 3.3 (1,50) 3.3 (1,50) 5.3 (,41) 5.3 (,41) 5.7 (,59) 5.9 (,68) 11.7 (5,3) 19.5 (8,86).0 (10,00) * Maximum available gap between pipe ends. Minimum gap = 0. Maximum Pressure and End Load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ for other pipe materials and/or wall thickness. Contact your GRINNELL Representative. ** Gold color coded metric bolt sizes for DN5 - DN couplings are available upon request. Max End Gap is for cut grooved standard weight pipe. May Page of
4 COUPLINGS Figure 705 Flexible Coupling For Fire Protection Pressure Rating and Listing / Approval information contact Tyco Fire Suppression & Building Products. Ductile Iron Housing Specifications ASTM A-536 Standard Specification for Ductile Iron Casting Grade Tensile Strength, minimum psi 65,000 (448 MPa) Yield Strength, minimum psi 45,000 (310 MPa) Elongation in (50mm), minimum 1% ASTM A-153 Standard Specification for Hot-Dip Galvanizing Bolt/Nut Specifications Carbon steel oval neck bolts and nuts are heat treated and conform to the physical properties of ASTM A-183 with a minimum tensile strength of 110,000 psi (760 MPa). Bolts and nuts are zinc electroplated to ASTM B-633. Coatings Orange Non-Lead (Standard) Fire Brigade Red Non-Lead (Optional) Hot-Dipped Zinc Galvanized (Optional) Gasket Specifications Grade A EPDMA, violet color code ambient to +150 F (+66 C) for fire protection systems. Not recommended for hot water systems. Tri-seal (Grade E EPDM), green color code for use in dry pipe or freezer systems. Prelubricated (Grade A EPDMA) Project: Date: Architect / Engineer: Contractor: Address: Notes: May PROJECT INFORMATION: Phone: Technical Data Sheet: TFP180 Date: July 004 APPROVAL STAMP: Page 1 of
5 COUPLINGS Figure 705 Flexible Coupling (cont.) Pipe Max. * Max. Max. Nominal Dimensions Deflection Net Bolt O.D. End Gap Pressure End load A B C / Wt. Per Size** Size Psi Lbs. Foot Lbs. Coupling Dia. x Lg. mm mm kpa N mm mm mm mm/m kg /8" x 1 /4" " 4-19' ,068, /8" x 1 /4" " 3-46' ,068 3, , /8" x 1 /4" 1.7 " 3-1' ,068 5, , /8" x 1 /4".0 1 " - 9' ,068 8, , mm - 3' M1 x ,068 9, , /" x 3" 3.0 3" - 3' ,068 1, M1 x , mm 3 - ' M1 x ,068 18, , /" x 3" 4.0 4" 3-11' ,068 1, M1 x , mm - 44' ,068 8, , mm - 36' ,068 31, , /8" x 3 1 /4" 7.0 5" - 35' ,068 3, , mm - 17' ,068 40, , mm - 1' ,068 44, , /8" x 3 1 /4" 7.1 6" - 10' ,068 45, , mm 1-40' M0 x ,068 75, , /4" x 4 3 /4" " 1-40' ,068 77, M0 x , " x 6 1 /" " 1-0' ,74 100, M4 x , " x 6 1 /" " 1-7' ,74 141, M4 x * Maximum available gap between pipe ends. Minimum gap = 0. Maximum pressure and end load are total from all loads based on standard weight steel pipe. Pressure ratings and end loads may differ on other pipe materials and/or wall thickness. Contact Tyco Fire Suppression & Building Products for details. See Fire Protection Equipment Submittal Sheet for Listing and Approval pressure ratings. ** Gold color coded metric bolt sizes are available upon request. Max End Gap and Deflection is for cut grooved standard weight pipe. Values for roll grooved pipe will be half that of cut grooved. May Page of
Couplings. Ductile Iron Housing Specifications. Coatings. Gasket Specifications. Bolt/Nut Specifications
Figure 71 Flange Adapters (ANSI Class 5/150) The Figure 71 Flange Adapter is capable of pressures up to 300 psi (20,7 bar) depending on pipe size and wall thickness. It provides a direct transition from
The applicable material specifications for ductile iron and rubber gaskets apply:
72 COUPLINGS - Grinnell Copper Grooved System is designed for joining copper tube size components 2" to 8" (54,0mm to 206,4mm) type K, L, M and DWV. All couplings and fittings are rated for working pressures
Mechanical MATERIAL SPECIFICATIONS. Stainless Steel Housing Specifications. Gasket Specifications. Bolt / Nut Specifications
82 COUPLINGS SYSTEM The Grinnell Stainless Steel System is designed for joining 2" to 12" (54,0mm to 206,4mm) stainless steel piping, schedules 5, 10, and 40. The Figure 472 coupling patented Universal
Grooved Piping Products
2 Grooved Piping Products Tyco Fire Products is ISO 9001 Certified with products manufactured in our newly constructed state of the art domestic ductile iron foundry and manufacturing facilities. We are
FIG Gruvlok Flange Adapter
FIG. 88 Gruvlok Adapter The Gruvlok Fig. 88 Adapter allows for direct connection of Class 125 or Class 150 flanged components to a grooved piping system. The Gruvlok Adapter provides an alternative method
B U I L D I N G C O N N E C T I O N S T H AT L A S T
B U I L D I N G C O N N E C T I O N S T H AT L A S T pipe to pipe and people to people. We pride ourselves in providing the finest-quality pipe products and services with integrity and dedication to superior
FIRE SPRINKLER EQUIPMENT SUBMITTAL
Fire Systems West, Inc. 206 FRONTAGE ROAD NORTH, SUITE C PACIFIC, WA 98047 (253) 833-1248 FIRE SPRINKLER EQUIPMENT SUBMITTAL FOR Being 4-20-21 VPAL MAINTENANCE SHED AND SUBSTATION FSW JOB NO. 02-11-11013
FIG Gruvlok Flanges
Gruvlok Flanges The Gruvlok Fig. 7012 Flange allows direct connection of Class 125 or Class 150 flanged components to a grooved piping system. The two interlocking halves of the 2" thru 12" sizes of the
Grooved Fire Protection. Installation Handbook
Grooved Fire Protection Installation Handbook October 2016 Grooved Fire Protection Installation Handbook OCTOBER 2016 IH-1000FP Worldwide Contacts www.tyco-fire.com GLOBAL HEADQUARTERS 1400 Pennbrook
Model CV-1FR Grooved-End Riser Check Valves 2 Inch to 12 Inch (DN50 to DN300) General Description. Installation. Technical Data
Worldwide Contacts www.tyco-fire.com Model CV-FR Grooved-End Riser Check Valves Inch to Inch (DN0 to DN00) General Description The TYCO Model CV-FR Grooved- End Riser Check Valve is a compact and rugged
Style Flange Adapter
Style 007 -- Flange Adapter Style 007 -- Flange Adapter is used for connect switches where valves, equipments or pipes have a flange interface. It realizes the change between flange connection and grooved
030/TL 03/01 50M, Copyright 2001, Anvil International $3. 50
030/TL 03/01 50M, Copyright 2001, Anvil International $3. 50 Pipe Fitter Handbook Another Anvil Advantage Mini-catalog Installation Procedures Technical Data Copyright 2001 by Anvil International, Inc.
COOPLOK Grooved Submittal. Material Specifications
SmithCooper International (SCI) COOPLOK Submittal Directions: Enter in the project information below; then print. Project /Job: Date: Engineer/rchitect: Contractor: ddress: Notes: Project Information System:
Housing Coating: Orange enamel. Hot dipped galvanized. Optional Bolts/Nuts: (Available in imperial size bolts and nuts only.)
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS The patented Style 107H rigid coupling joins 8"/50 200 standard roll grooved and cut grooved steel pipe.* The joint is assembled without disassembling the bolts,
GROOVED COUPLINGS - STANDARD FLEXIBLE Model 101
GROOVED COUPLINGS - STANDARD FLEXIBLE Model 101 Available Sizes 1" through 12" (25 through ) Pipe Material Carbon steel, Schedule 10, Schedule 40. For use with alternative materials and wall thicknesses
QuickVic Rigid Coupling for Steel. System No. Submitted By Spec Sect Para Location Date Approved Date CARBON STEEL PIPE GROOVED COUPLINGS
H ONL. SEE PAGE 4 FOR DETAILS. The patented Style 107 rigid coupling joins 12"/50 300 standard roll grooved and cut grooved steel pipe. The joint is assembled without disassembling the bolts, nuts, gasket
GRINNELL Model B302 and Model BN302 Grooved End Butterfly Valves with Gear Operators or Lever-Lock Operators General Description
Technical Services -00- +-0--0 www.grinnell.com GRINNELL Model B0 and Model BN0 Grooved End Butterfly Valves with Gear Operators or Lever-Lock Operators General Description The GRINNELL Models B0 and BN0
Grinnell Grooved Fire Protection Products Grooved Fittings
Technical Services: Tel: (800) 38-932 / Fax: (800) 79-5500 www.tyco-fire.com Grinnell Grooved Fire Protection Products Grooved Fittings General Description LPCB Vd S The grooved fittings provide an economical
Style 99 Roust-A-Bout Couplings
R IPS CARBON STEEL PIPE PLAIN END SYSTEM Style 99 Roust-A-Bout Couplings 14.02 VICTAULIC IS AN ISO 9001 CERTIFIED COMPANY PRODUCT DESCRIPTION 1 1 / 2-12" Sizes 14-18" Sizes Style 99 Roust-A-Bout couplings
Hot dipped galvanized. Optional Bolts/Nuts: (Available in imperial size bolts and nuts only.)
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS The Style 177 QuickVic flexible coupling is installation-ready, and joins 2-8"/50-200 standard roll grooved and cut grooved steel pipe. The coupling's unique
Victaulic Suction Vibration Isolation Pump Drop Series 337 Korea Only
Victaulic Suction Vibration Isolation Pump Drop Series 337 Korea Only 2.37 1.0 PRODUCT DESCRIPTION Available Sizes 3 12"/DN80 DN300 Maimum Working Pressure Rated to the working pressure of the PN/PN16
Model 7706 Reducing Coupling. Deg. Axial Displacement
MODEL 7706 REDUCING COUPLING The Model 7706 Reducing allows direct reduction on a piping run and eliminates the need for a concentric reducer and couplings. The specially designed rubber gasket prevents
GRINNELL Model B303 Grooved End Butterfly Valves with Gear Operators or Lever-Lock Operators General Description
Worldwide Contacts www.grinnell.com GRINNELL Model B Grooved End Butterfly Valves with Gear Operators or Lever-Lock Operators General Description The GRINNELL Model B Butterfly Valves provide for efficient
Grooved Piping System for Fire Protection Services
Grooved Piping System for Fire Protection Services 1.01 General: A. Section Includes: 1. General 2. Materials: a. Pipe b. Victaulic Couplings c. Victaulic Fittings d. Hole and Branch Outlets e. Victaulic
Size Inches UL ULC FM. Pipe Sch.
IPS CARBON STEEL PIPE - FIRE PROTECTION PRODUCTS FireLock Rigid Coupling STYLE 005 WITH VIC-PLUS GASKET SYSTEM (NORTH AMERICA ONLY) FireLock Style 005 rigid coupling has a unique, patented angle-pad design
GRINNELL Model B302 and Model BN302 Grooved End Butterfly Valves with Gear Operators or Lever-Lock Operators General Description
Worldwide Contacts www.grinnell.com GRINNELL Model B0 and Model BN0 Grooved End Butterfly Valves with Gear Operators or Lever-Lock Operators General Description The GRINNELL Model B0 and Model BN0 Butterfly
Hole-cutting. cutting a hole. After the hole has been cut all rough edges must be removed and the area within 5/8 (16mm) of the hole
Mechanical Tees Hole-cutting Shurjoint mechanical tees provide a fast and easy mid-point branch outlet, eliminating the need for welding or the use of multiple fittings. The Model M21 features a female
Grooved Piping System for Fire Protection Services
Grooved Piping System for Fire Protection Services 1.01 General: A. Section Includes: 1. General 2. Materials: a. Pipe b. Victaulic Couplings c. Victaulic Fittings d. Hole and Branch Outlets e. Victaulic
Ford Fabricated Steel Products
Ford Fabricated Steel Products Section N2 12/2000 The Ford Meter Box Co., Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 219/563-3171 FAX: 1-800-826-3487 Overseas
Grooved End Fittings. System No. Submitted By Spec Sect Para Location Date Approved Date CARBON STEEL PIPE - GROOVED FITTINGS
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS Victaulic offers a broad line of fittings in sizes through 60"/1500 in a variety of straight and reducing styles. Most standard fittings are cast of durable
Grooved End Fittings. System No. Submitted By Spec Sect Para Location Date Approved Date CARBON STEEL PIPE - GROOVED FITTINGS
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS Victaulic offers a broad line of fittings in sizes through 60"/1500 in a variety of straight and reducing styles. Most standard fittings are cast of durable
Style 234 Restrained Flexible Single-Gasket Coupling. System No. Submitted By Spec Sect Para Location Date Approved Date
Victaulic Bolted Split-Sleeve Products (VBSP) Style 234 carbon steel couplings (formerly Depend-O-Lok Air/FluidMaster) are single-arch couplings that are commonly used in buried or exposed steel pipe applications
Victaulic Standard Grooved and Advanced Grooved (AGS) Piping System for IPS Steel 2 (DN 50) through 60 (DN1500)
Victaulic Standard Grooved and Advanced Grooved (AGS) Piping System for IPS Steel 2 (DN 50) through 60 (DN1500) 1.01 General: A. Section Includes: 1. General 2. Materials: a. Pipe b. Victaulic Couplings
Vic-Strainer WARNING. System No. Submitted By Spec Sect Para Location Date Approved Date IPS CARBON STEEL PIPE - GROOVED ACCESSORIES SERIES 730
Series 730 Vic-Strainer is lighter than flanged Y type strainers and provides straightthrough flow for lower pressure drop. It installs with two Victaulic couplings, and is rated up to 750 psi/5175 kpa
UNITED BRAND FITTINGS
UNITED BRAND FITTINGS ANSI B. Class 5 ( ~ ) AWWA C Class 0 (3 ~ ) Our dedication to the mechanical piping industry has given us the opportunity to provide you with a quality comprehensive line of flanged
Grooved End Fittings. System No. Submitted By Spec Sect Para Location Date Approved Date CARBON STEEL PIPE - GROOVED FITTINGS
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS Victaulic offers a broad line of fittings in sizes through 48 /1200 in a variety of straight and reducing styles. Most standard fittings are cast of durable
Grooved End Fittings. System No. Submitted By Spec Sect Para Location Date Approved Date CARBON STEEL PIPE - GROOVED FITTINGS
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS Victaulic offers a broad line of fittings in sizes through 60"/1500 in a variety of straight and reducing styles. Most standard fittings are cast of durable
JIS G (SGP)
JIS G 3452-1988 (SGP) Nominal size Outside Diameter Thickness Unit Weight (plain end) A B mm in mm in lb/ft kg/m 6 1/8 10.5 0.413 2.0 0.079 0.282 0.419 8 1/4 13.8 0.543 2.3 0.090 0.438 0.652 10 3/8 17.3
Victaulic Specification Power Industry
Victaulic Specification Power Industry 1.01 General: A. Section Includes: B. Submittals: C. References: 1. General 2. Materials: a. Pipe b. Victaulic Couplings c. Victaulic Fittings d. Victaulic Valves
with the specific application. Always read and understand the installation
Worldwide Contacts www.tyco-fire.com Resilient-Seated Gate Valves Outside Screw and Yoke General Description TYCO Resilient-Seated Gate Valves are used in Fire Protection Systems for on/off operation.
EMCO Corporation Waterworks is not responsible for any errors and discrepencies in the products depicted herein. Information is provided directly
EMCO Corporation Waterworks is not responsible for any errors and discrepencies in the products depicted herein. Information is provided directly from our suppliers. aquamine pvc piping products Victaulic
GRUVLOK FITTINGS FOR GROOVED-END PIPE
GRUVLOK FITTINGS FOR GROOVED-END PIPE Gruvlok fittings are available through 24" nominal pipe size in a variety of styles. Use the Fitting Table to convert nominal pipe size to corresponding pipe These
Technical Data. Sizes 2 in. to 24 in. (DN50 to DN600) Approvals UL and ULC Listed FM Approved
Worldwide Contacts www.tyco-fire.com Model TJP Resilient-Seated Gate Valves with Vertical or Cross Wall Post Indicator General Description TYCO Model TJP Resilient-Seated Gate Valves with Vertical and
Steel Fabricated Coupling
Steel Fabricated Coupling Straight Connection IMPORTANT LINKS Click appropriate words to go to: Standard Limited Warranty Sales Terms & Conditions Freight Policy Returns Policy Corrosion & Product Selection
Presby Steel, LLC. 143 East Milan Road Berlin, NH FAX:
143 East Milan Road 603-752-3022 FAX: 603-752-2821 1 S BEAMS (I Beams) Conforms to ASTM A36 Designation Web Depth/Inches Thickness Flange in Inches Area x Wt./Ft./Lbs. in Inches Width Thickness Sq. In.
Section 2. Shurjoint Grooved Fittings Flow Data / Friction Resistance Ductile Iron Grooved Fittings. Wrought Grooved Fittings
Section 2 Cast & Wrought Grooved Fittings Shurjoint Grooved Fittings... 56 Flow Data / Friction Resistance... 56 Ductile Iron Grooved Fittings 7110 / 7111 / 7112 / 7113 Elbows... 57 7120 / 7135 / 7130
' ' ' ' LISTED Elbows Tees Crosses Wyes Reducers Flanges Converters Gaskets Nuts&Bolts
.., I.,.,... I I...... I I ',,,, ", Elbows Tees Crosses Wyes Reducers Flanges Converters Gaskets Nuts&Bolts ' ; i ',,.) I ' ' ' ' AWWA C Class 50 (3"' ANSI B. Class 5 ("' ANSI B. Class 50 (3"' c@us LISTED
UNITED BRAND FITTINGS
FLANGE DETAILS Class 5 S ize O.D. B.C. T Bolt Hole Bolt Dia. & of Dia. Length Bolts 4.75 5/ 8 4 x 4 50 4 x 4 3 4 4 x 4 4 00 5/ 4 x 3 8 5.00 50 5/ 7/ 8 4 x 3 8 6.00 50 7/ 8 4 x 3 8 8 3.50.75 8 7/ 8 4 x
STAINLESS STEEL SYSTEMS
STAINLESS STEEL SYSTEMS 139 Systems Table of Contents Figure 472 Rigid Couplings Page 142 Figure 401 45 Elbows Page 149 Figure SS-7X Rigid Couplings (Large Diameter) Page 143 Figure 405 Flexible Couplings
Advantages of Grooved Fittings
Grooved Fittings Advantages of Grooved Fittings Comparative Advantages Allows angular deflection-misalignment Expansion, contraction or, no need for expansion joint Reclaimable, no need for union Allows
Full Traceability. Material Specification. Raw Material Code. Heat Treatment
All J.B. Smith swages, bull plugs, tubing and casing nipples, and chambers are traceable to the original mill test report. To ensure traceability, all fittings are steel stamped as follows: Material Specification
Rated to the New, Higher Pressure Classes in Latest Editions of AWWA C900 and C909. Joint Restraint Products
Pipe Restrainers series 1000G2 1000G2C Restrainers for AWWA CI OD C900/C909 PVC/PVCO Pipe with MJ or Ductile Iron Push-On Fittings (Formerly Series 9000) INFORMATION Second Generation (Gen 2) PVC Restrainers
Victaulic Discharge CBV Vibration Isolation Pump Drop Series 383/383G
Victaulic Discharge CBV Vibration Isolation Pump Drop Series /G 2..0 PRODUCT DESCRIPTION Available Sizes 2"/ - 00 Offered in full or reduced port size (see Section.0 for details). Maimum Working Pressure
11.02 Mechanical-T Bolted Branch Outlets
STLES AND SEE ICTAULIC PUBLICATION 10.01 FOR DETAILS NIIPO ictaulic Mechanical-T Outlet provides a direct branch connection at any location a hole can be cut in pipe. The hole is cut oversize to receive
MANUFACTURING SPECIFICATION
Swage Nipples, Bull Plugs & Oil Country Fittings Catalogue SWAGE NIPPLES, BULL PLUGS, OIL COUNTRY FITTINGS, COUPLINGS, LOW TEMP & STAINLESS SWAGES MANUFACTURING SPECIFICATION CSP Products Ltd, manufactures
Section 3. Stainless Steel Series. Shurjoint Stainless Steel Piping Series Grooved Mechanical Couplings. Cast Grooved Fittings.
Section 3 Stainless Steel Series Shurjoint Stainless Steel Piping Series... 84 Grooved Mechanical ouplings SS-5 Rigid oupling... 85 SS-7 Rigid oupling... 86 SS-7X Rigid oupling... 87 SS-8 Flexible oupling...
Lenntech Tel Fax
SEE VICTAULIC PUBLICATIO.01 FOR DETAILS Style 99 Roust-A-Bout couplings are designed with heavy housings and grips to provide a strong component for joining plain and beveled end, including Schedule steel
TRUSTED FOR 150 YEARS
G-2005 Today Anvil International is the largest and most complete fitting and hanger manufacturer in the world. 2004 Anvil International acquires Star Pipe Products, Building and Construction Divisions
Mechanical Piping Products
October 202 For the most current product/pricing information on Anvil products, please visit our website at www.anvilintl.com. Mechanical Piping Products b u i l d i n g c o n n e c t i o n s t h a t l
SUBMITTAL PACKAGE FIRE PROTECTION VALVES
SUBMITTAL PACKAGE FIRE PROTECTION VALVES Butterfly Valves Ductile Iron Grooved...pg 2-5 Grooved Check Valves...pg 6-8 OS&Y Valves...pg 9-12 ARGCO.com 800-854-1015 Updated 2/27/2017 ARGCO GROOVED BUTTERFLY
STANDARD PIPE CLAMP FIG. 520 & 521
Designed to be used in the suspension of non-insulated pipe lines. Normally used in conjunction with Fig. 35 weldless eye nut, Fig. 50 eye rod or Fig. 55 welded eye rod to allow flexibility at the rod
SEE VICTAULIC PUBLICATION FOR DETAILS
dapters SEE VICTULIC PULICTION 10.01 FOR DETILS Style 741 Style 741 adapter is designed for directly incorporating flanged components with NSI CL. 125 or CL. 150/PN10 and PN16 or ustralian Standard Table
Ford Service Saddles and Tapping Sleeves
DQS Inc. Section AA 09/2017 THE FORD METER BOX COMPANY, INC. CERTIFIED TO ISO 9001:2015 10004466 Ford Service Saddles and Tapping Sleeves Contents Recommended Product Application *Steel *C900/909*** Cast
Series 756 FireLock Dry System Check Valve
R IPS CARBON STEEL PIPE FIRE PROTECTION PRODUCTS Series FireLock Dry System Check Valve Grooved X Grooved and Flanged X Grooved 0.0 VICTAULIC IS AN ISO 900 CERTIFIED COMPANY PRODUCT DESCRIPTION The Victaulic
Section 8 AMERICAN. Flanged Pipe
Section 8 AMERICAN Flanged Pipe The principal standards covering Flanged Pipe are ANSI/AWWA C115/A21.15 and ANSI/AWWA C110/A21.10. These and other standards are referenced throughout this Section either
DV-5a Automatic Water Control Valve Single Interlock Preaction Fire Protection Systems 1-1/2 Inch to 8 Inch (DN40 to DN200) General Description
Worldwide Contacts www.tyco-fire.com DV-5a Automatic Water Control Valve Single Interlock Preaction Fire Protection Systems 1-1/ Inch to Inch (DN40 to DN00) General Description The TYCO DV-5a Automatic
MACRO HP. NEW SMALLER SIZES Macro HP is Now Available for 2-12 inch Pipe Sizes. patent number:
ACROMACROMACROMA MACRO HP ROMAC S SECOND GENERATION TWO-BOLT E X T E N D E D R A N G E C O U P L I N G NEW SMALLER SIZES Macro HP is Now Available for 2-12 inch Pipe Sizes patent number: 8448993 BMACROHP
THOMAS. Unifit Premier Series. Couplings & Flange Adaptors Non Restrained Products PIPE PRODUCTS
THOMAS Couplings & Flange Adaptors Non Restrained Products PIPE PRODUCTS Unifit Premier Series Universal Pipe Couplings and Flange Adaptors for all Rigid Pipe J1 Unifit Premier Series Application Locally
TABLE OF CONTENTS. Pipe Diameter Chart (Reference Only)..50 Extensions 38,40,42,44
TABLE OF CONTENTS Item Page Item Page ANSI/AWWA Compact & Full Body Pipe Fittings: Product Submittals and Installation: Mechanical & Flange Joint C153. 3-9 20U Protective Fusion Bonded Epoxy....5,5 Mechanical
GBV-G Balancing Valves
Ductile Iron ASTM A6, Grade 6-4-2 The Series GBV is a multi-turn, Y-style globe valve designed for accurate determination and control of fluid flow to circuits requiring precise balancing. Max. Working
Ford Brass Saddles Style 101B and 202B
101B Ford Brass Saddles 101B and 202B 101B, 3/4" and 1" Taps 202B, 3/4" through 2" Taps Specifications Body - 85-5-5-5 brass alloy as per ASTM B62, ASTM B584 and AW WA C800. Threads may be FIP, AW WA,
UNITED BRAND FITTINGS
NFF0711 UNITED DUCTILE IRON CLASS 0 FLANGED FITTINGS UNITED BRAND FITTINGS AWWA C1, ANSI A21. Our dedication to the mechanical piping industry has given us the opportunity to provide you with a quality
Product catalogue. Mechanical accessories for pumps and mixers
Product catalogue Mechanical accessories for pumps and mixers Contents Mixer accessories Single guide bar system...4 Double/tripod guide bar system...9 Cantilever system...14 Bottom fixing plate system...15
Product Catalog. Rev. 612 r1
Product Catalog Rev. 612 r1 PIPE FITTINGS CONDUIT FITTINGS PRODUCT CATALOG Pipe Nipples Welded and Seamless Carbon Steel 2 Pipe Nipples Welded and Seamless Stainless Steel 3 Pipe Nipples End Finishes 4
SECTION COMMON WORK RESULTS FOR FIRE SUPPRESSION. A. Pipe, fittings, valves, and connections for sprinkler systems.
SECTION 210500 - COMMON WORK RESULTS FOR FIRE SUPPRESSION PART 1 GENERAL 1.1 SECTION INCLUDES A. Pipe, fittings, valves, and connections for sprinkler systems. 1.2 RELATED REQUIREMENTS A. Section 099000
Series 758 FireLock Actuated System Valve
R IPS CARBON STEEL PIPE FIRE PROTECTION PRODUCTS Series 58 FireLock Actuated System Valve With Deluge Trim Grooved X Grooved and Flanged X Grooved 30.04 VICTAULIC IS AN ISO 9001 CERTIFIED COMPANY PRODUCT
08.08 Vic-Check Valves
The check valves are a product of computer-assisted innovative engineering with quality features including a new hydrodynamically efficient profile. The Vic-Check valve utilizes a spring-assisted, single-disc
VR Piston Check Valves Submittal Data Sheet. Job or Customer: Engineer: Contractor: Submitted by: Approved by: Order No: Specification: introduction
Submittal Data Sheet Job or Customer: Engineer: Contractor: Submitted by: Approved by: Order No: Specification: Date Date Date introduction < STANDARDS > The IPEX VR Piston Check Valve is an ideal solution
TECHNICAL DATA OBSOLETE
August 31, 2006 Check Valve 815a 1. PRODUCT NAME Viking Easy Riser Swing Check Valve Model E-1: Available since 1992 Model F-1: Available since 1994 2. MANUFACTURER The Viking Corporation 210 N. Industrial
Series 751 FireLock European Alarm Check Valve Stations
R IPS CARBON STEEL PIPE FIRE PROTECTION PRODUCTS Series FireLock European Alarm Check Valve Stations Grooved X Grooved 0.0 VICTAULIC IS AN ISO 00 CERTIFIED COMPANY PRODUCT DESCRIPTION The Victaulic Series
2500 PSI STANDARD FEATURES 2500 PSI CYLINDERS
2500 PSI STANDARD FEATURES Intended Use: Double acting applications Rated Pressure: 2500 PSI Material: High Tensile SAE C1045, ground and polished hard chrome plated Barrel Material: High tensile SAE C1026/St52.3
Section N. 09/2017 Web Revision 10/23/2017 THE FORD METER BOX COMPANY, INC. CERTIFIED TO ISO 9001: Ford Fabricated Steel Products
DQS Inc. THE FORD METER BOX COMPANY, INC. CERTIFIED TO ISO 9001:2015 10004466 Section N 09/2017 Web Revision 10/23/2017 Ford Fabricated Steel Products Contents Page Product Numbering System... 3 Information...............................................................
Utilities Catalog. PC-U2008, February, 2008
Utilities Catalog PC-U2008, February, 2008 Tyler Utilities 11910 CR. 492 Tyler, Texas 75706 (800) 527-8478 Union Foundry Company Box 309 Anniston, Alabama 3602 (800) 226-7601 TABLE OF CONTENTS Item Page
CHAIN & HOOKS. Proof Coil Chain Grade 28. Transport Chain Grade 70
Proof Coil Chain Grade 28 Proof coil chain is suitable for use as towing chain, logging,fencing, trailer safety chain, boat anchors, security barriers or other general purposes where chain of high tensile
StarFlex series 5000 Double-Ball Flexible Expansion Joint for the Protection of Water Wastewater, and Industrial Pipelines
Joint Restraint Products StarFlex series 5000 Double-Ball Flexible Expansion Joint for the Protection of Water Wastewater, and Industrial Pipelines INFORMATION StarFlex Flexible Expansion Joints can deflect
Introduction. We stay ahead of today s evolving market requirements by committing to a program of continued research and development.
Pipes & Fittings SHIELD Introduction SHIELD is a company created to cater to the infrastructure, fire protection and building services industries with a comprehensive range of products designed to be competitive
Ford Service Saddles and Tapping Sleeves
Section AA 04/2013; web revision 02/2014 Ford Service Saddles and Tapping Sleeves The Ford Meter Box Company, Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 260-563-3171
Pipe hanger solutions
Product catalog Middle East offering Pipe hanger solutions for commercial and industrial applications B00 series B00 - Standard clevis hanger Pipe will not pinch when installing. 5 swing in either direction
MICROMOLD TM. PTFE Gaskets. Product Specifications. Envelope & Solid Donut Style 1, 2, 3 Sanitary
MICROMOLD TM ENGINEERED PLASTIC FLUID-FLOW PRODUCTS Product Specifications 7.20-2 PTFE Gaskets Envelope & Solid Donut Style 1, 2, 3 Sanitary Gaskets CONTENTS Sizes of PTFE Gaskets...... Slit Envelope Gaskets
Model-1 Natural Gas Valves
Flanged End 285 Screwed Weld End Locking Devices KEROTEST Model-1 s Short Weld End Long Weld End Weld x Flange 500 / 740 Flanged End 500 / 740 Weld x Flange 285 Model-1 Short Weld End Standard Welding
Super Flange series 7200 Designed for use on Ductile Iron, Steel, PVC, PVCO and HDPE Pipes
Designed for use on Ductile Iron, Steel, PVC, PVCO and HDPE Pipes INFORMATION The Series 7200 Super Flange is a restrained flange adapter designed to connect plain end pipe to a flange end component. May
INTEGRATED PIPING SYSTEMS. Technical manual. VSH Shurjoint
INTEGRATED PIPING SYSTEMS Technical manual VSH Shurjoint Disclaimer: The technical data are non-binding and do not reflect the warranted characteristics of the products. They are subject to change. Please
HIGH PERFORMANCE STEEL ANCHORS
Throughbolt zinc plated, -HD Throughbolt hot dip galvanized anchor name BASE MATERIALS: concrete, stone non-cracked concrete PRODUCT CODE -10080/20 -HD-06050/10 zinc coat type thread diameter length FEATURES:
Cooper & Turner Ltd STRUCTURAL
Cooper & Turner Ltd STRUCTURAL Page 1 of 6 Dimensions of Fully Threaded Bolts/Setscrews CHARACTERISTIC STANDARD Thread d M12 M16 M20 M24 M30 M36 p (pitch) 1.75 2 2.5 3 3.5 4 a max. 5.3 6 7.5 9 10.5 12
Product Specifications PIPE SUPPORT PRODUCTS
Product Specifications PIPE SUPPORT PRODUCTS For the most up to date information visit our website: www.taylorassociates.com 1 PICTORIAL INDEX FIG. 41 Page 8 FIG. 41 PVC Page 9 Fig. 42 Page 10 FIG. 43
SJ-300N J-04. Model SJ-300N-L Butterfly Valve with Lever Handle
SJ-300N J-04 MODEL SJ-300N BUTTERFLY VALVE The Model SJ-300N Butterfly Valve is a grooved-end tight shut-off valve designed, manufactured and tested to MSS SP-67. The valve can be shipped either with a
Model MTB-ASME Vertical Pre-Piped Bladder Tanks
DATA SHEET Model MTB-ASME Vertical Pre-Piped Bladder Tanks Features n Pre-piped configurations with a wide selection of proportioner sizes, including the SKUM TPW-150 MK2 for closedhead sprinkler systems
DV-5a Automatic Water Control Valve Double Interlock Preaction Fire Protection Systems 1-1/2 Inch to 8 Inch (DN40 to DN200) General Description
Worldwide Contacts www.tyco-fire.com DV-5a Automatic Water Control Valve Double Interlock Preaction Fire Protection Systems 1-1/2 Inch to Inch (DN40 to DN200) General Description The TYCO DV-5a Automatic
FloCheck is a precision engineered, twin plate check valve suitable for product or service lines, wherever non-return protection is required.
FloCheck is a precision engineered, twin plate check valve suitable for product or service lines, wherever non-return protection is required. Features Twin plate, flat seat design for enhanced sealing.
1. Valves shall conform to the latest version of AWWA Standard C-509 covering Resilient Seated gate Valves for Water Supply Service.
KENNEDY KENNEDY VALVE MODEL VALVE KS-RW 1. Valves shall conform to the latest version of AWWA Standard C-509 covering Resilient Seated gate Valves for Water Supply Service. 2. The valves shall have a cast