National Crane Series NBT60 Product Guide
|
|
- Agatha Gray
- 6 years ago
- Views:
Transcription
1 National Crane Series NBT Product Guide ASME B30.5 Imperial % Features 39,01 m (128 ft) five-section full power boom 54,4 t ( USt) at 2,44 m (8 ft) Self-lubricatg Easy Glide wear pads Hydraulically removable counterweight system Heavy lift load charts available
2 Features National Crane NBT 54,4 t ( USt) maximum capacity 41,1 m (1 ft) maximum tip height (ma boom) 54,6 m (179 ft) maximum tip height (boom with extension) Five-section boom The Series NBT is equipped with a 39,0 (128 ft) boom. An optional 7,9 m - 13,7 m (26 ft - ft) two-section offsettable manual extension is available. Counterweight Two-piece 1361 kg ( lb) each (total 2722 kg [00 lb]) hydraulically removable counterweight slabs. Removable counterweight slabs can be stowed on front outrigger box for roadg. Outriggers Equipped with left and right ground-level and cab CANbus outrigger controls. The Series NBT outriggers allow quick and easy crane set-up and cludes a new outrigger beam position sensg system that aids the operator selectg the right load chart based on the crane s outrigger footprt. The front outrigger box has an X-shaped footprt that elimates the need for a sgle front outrigger. Dimensions: Full span: Front: 7,09 m (23 ft 3 ) Rear: 7,39 m (24 ft 3 ) Mid span: Front: 4,72 m (15 ft 6 ) Rear: 4, m (16 ft 1 ) Retracted-front and rear: 2,39 m (7 ft 10 ) Deluxe operator s cab The Series NBT operator s cab cludes all-steel construction with acoustical lg and tted glass throughout, air conditiong, deluxe seat with arm rest mounted sgle-axis electric controllers, wdshield and slidg skylight with electric wipers, diesel heater with defroster, circulatg fan, fire extguisher, and dual cab mounted work lights.
3 Features *Product may be shown with optional equipment. National Crane is proud to troduce the Series NBT crane The Series NBT represents the pnacle of mache performance, combg the latest both hydraulic and electronic mache control. This new product provides premium operator comfort with the latest Manitowoc cab design, simplified mache setup with no need for an SFO and front bumper control of the hoist(s). The cable follower will keep constant tension on the rope reducg the potential for bundlg Speedy-reeve boom tip and sheave blocks simplify riggg changes by decreasg the time needed to change le reevg Easy Glide boom wear pads reduce the conditions that cause boom chatter and vibration. The net result is smoother crane operation Pressure compensated, load sensg hydraulic system - PTO mounted axial piston pump - Superstructure mounted reservoir with tegral suction valve/filter, return filter, sight gauge, and temperature gauge - Oil cooler with 6 mm (16 ) fan and temperature sensor - Pressure transducers tegral to the lift cylder holdg valve LMI system features a 178 mm (7 ) graphical, color display, data logger, error codg, and a USB connection port. Real time crane formation is displayed with numerous operator features cludg: soft metric load chart conversion, hydraulic filter change remders, an electronic hour meter, and truck diagnostics (fuel level, coolant temperature, and DPF status). The display console allows each crane control function to be set dependently to reduce speed (%, %, %, and 30%) Dual axis controls are optional for superior operator control, along with standard air conditiong, a diesel heater and ergonomic seat
4 Contents Specifications 5 Weights 7 Mountg configurations 8 Dimensions 10 Heavy lift (workg range and load charts) 12 Mimum truck (workg range and load charts) 34 Accessories 56
5 Specifications Boom and extension combations data NBT-128: Equipped with a 9,7 m - 39,0 m (31.7 ft ft) five-section boom. This model can be equipped with a 7,9 m - 13,7 m (26 ft - ft) two-section offsettable extension, providg a maximum tip height of 54,6 m (179 ft). 9,7 m - 39,0 m (31.7 ft ft) five-section full power boom FJM-0S 7,9 m - 13,7 m (26 ft - ft) two-section offsettable and 3 manual extension Note: Maximum tip is measured with outriggers/stabilizers fully extended. Series NBT 5
6 Specifications NBT Series provisional wch data 1 part le max. pull 2 part le max. pull 3 part le max. pull 4 part le max. pull 5 part le max. pull 6 part le max. pull 7 part le max. pull 8 part le max. pull 9 part le max. pull 10 part le max. pull 11 part le max. pull Standard planetary wch Headache ball 1-sheave 2-sheave 5-sheave Low speed 5103 kg (11,2 lb) 58,2 m/m (191 fpm) kg (22,0 lb) 28,9 m/m ( fpm) kg (33,7 lb) 19,2 m/m (63 fpm) kg (,000 lb) 17,3 m/m (47 fpm) kg (56,2 lb) 11,6 m/m (38 fpm) kg (67,0 lb) 9,4 m/m (31 fpm) 712 kg (78,7 lb) 8,2 m/m (27 fpm) 824 kg (,000 lb) 7,0 m/m (23 fpm) 926 kg (101,2 lb) 6,4 m/m (21 fpm) kg (112,0 lb) 5,8 m/m (19 fpm) kg (120,000 lb) 5,3 m/m (17 fpm) High speed 2268 kg (5,000 lb) 116,7 m/m (383 fpm) 36 kg (10,000 lb) 58,2 m/m (191 fps) 64 kg (15,000 lb) 38,7 m/m (127 fpm) 72 kg (20,000 lb) 28,9 m/m ( fpm) 11 3 kg (25,000 lb) 23,2 m/m (76 fpm) 13 8 kg (30,000 lb) 19,2 m/m (63 fpm) kg (,000 lb) 16,5 m/m (54 fpm) kg (,000 lb) 14,3 m/m (47 fpm) kg (,000 lb) 12,8 m/m (42 fpm) 22 6 kg ( lb) 11,6 m/m (38 fpm) kg (,000 lb) 10.6 m/m (34 fpm) *Cable supplied is 16 mm (5/8 ) diameter roation resistant IWRC. Average breakg strength kg (56,0 lb). All wch pulls and speeds are shown on the fourth layer. Wch le pulls would crease on the first, second, and third layers. Wch le speed would decrease on the first, second, and third layers. Wch le pulls may be limited by the wch capacity or the ANSI 5 to 1 cable safety factor. Wch Fourth layer pull Allowable cable pull Standard planetary and auxiliary planetary 2268 kg (00 lb) high speed 5117 kg (11,2 lb) low speed 5117 kg (11,2 lb) 5117 kg (11,2 lb) Loadle deduct Aux boom nose 36 kg ( lb) 7 USt Downhaul weight 78 kg (171 lb) 20 USt 1-sheave block 181 kg (0 lb) USt 3-sheave block 272 kg (0 lb) USt 5-sheave block 498 kg (1098 lb) 6
7 Weights Standard NBT Configuration Horizontal CG mm () Weight and CG estimates (see notes) Weight w/fluids kg (lb) CWT pned (# slabs) CWT stowed (# slabs) NBT (17.2) (,9) 2 0 NBT (33.4) (,9) 1 1 NBT (49.8) (,9) 0 2 NBT (26.9) (47,893) 1 0 NBT (44.4) (47,893) 0 1 NBT (.9) (44,121) 0 0 Weight and center of gravity notes: 1. Information provided is for reference only (calculated weights). 2. Weight and CG data is applicable for a standard mache: 128 ft boom 2/3 part le block cluded Ma hoist only (IPO counterweight stalled) Standard deckg with fixed access ladder No boom extension equipped No optional turret access step No aux nose or optional hook blocks 3. All counterweight configurations are shown table: Pned = attached to cylders and turret ( use) Stowed = attached to torsion box (not use) 2 = top & bottom slabs 1 = top or bottom slab only 0 = No slab pned and/or stowed If both stowed and pned columns are 0, the counterweight is physically removed from the mache. IPO is also assumed removed this case. For more formation about mountg configuration options, please contact your local National Crane dealer. Series NBT 7
8 Mountg configurations Configuration 1 -NBT128 (4-axle Mimum Truck) 9782 mm (31' 11") Retracted mm (128' 0") Extended w/out jib 38 mm (146") Tailswg (2) slabs pned 1372 mm (54") 20 mm (13' 2 1/4" ) Overall height 6 mm (14") 1143 mm (") 1194 mm (47") 16 mm (77") 4877 mm (192") 2794 mm (110") 6 mm (16") CLR to CA 6833 mm (269") 11 2 mm (36' 10 1/2") mm (39' 8 1/4") Overall length Workg area 36 Gross Axle Weight Ratg, Front 72 kg (20,000 lb) Gross Axle Weight Ratg, Rear kg (66,000 lb) Gross Vehicle Weight Ratg kg (86,000 lb) Wheelbase (WB) 683 cm (269 ) Cab to Axle/Cab to Trunnion (CA/CT) 488 cm (192 ) Frame Strength Frame Section Modulus (SM); front axle to end of AF Stability Weight, Front Stability Weight, Rear 7 MPa (110,000 PSI) 327 cm3 (20 3) 44 kg ( lb) 56 kg (12,0 lb) *NOTE: Estimated axles scale weights prior to stallation of crane assembly for % stability. Configuration 2 NBT128 (Heavy Lift Truck Tandem/Tridem) Boom extended to mm (33' 3 1/2") 9782 mm (31' 11") Retracted mm (128' 0") Extended w/out jib 3632 mm (143") Tailswg (2) slabs stowed 1372 mm (54") 20 mm (13' 2 1/4" ) Overall height 1143 mm (") Truck height 864 mm (34") 1194 mm (47") 2108 mm (83") 1829 mm (72") 762 mm (30") 62 mm (256") 5918 mm (233") 7417 mm (292") mm (37' 8 1/4") mm (41' 0 1/2") Overall length 2794 mm (110") 584 mm (23") CLR to CA 2489 mm (98") Afterframe 8 Workg area 36 Gross Axle Weight Ratg, Front kg (,000 lb) Gross Axle Weight Ratg, Rear kg (66,000 lb) Gross Vehicle Weight Ratg 48 0 kg (106,000 lb) Wheelbase (WB) 742 cm (292 ) Cab to Axle/Cab to Trunnion (CA/CT) 546 cm (215 ) Frame Strength Frame Section Modulus (SM); front axle to end of AF Stability Weight, Front Stability Weight, Rear 7 MPa (110,000 PSI) 327 cm3 (20 3) 69 kg (15,300 lb) 5125 kg (11,300 lb) *NOTE: Estimated axles scale weights prior to stallation of crane assembly for % stability.
9 Mountg configurations Configuration 3 NBT128 (7-axle-Federal Bridge Law Compliant) Boom extended to 11 m (') 9782 mm (31' 11") Retracted mm (128' 0") Extended w/out jib 38 mm (146") Tailswg 1346 mm (53") (2) Slabs stowed 1372 mm (54") 20 mm (13' 2 1/4" ) Overall height 864 mm (34") 737 mm (29") 2362 mm (93") 13 mm (71") 1092 mm (43") 2896 mm (114") 7442 mm (293") mm (39' 4 3/4") 1397 mm (") 6 mm (14") CLR to CA 1397 mm 1346 mm (53") (") 3429 mm (1") MIN Afterframe 1143 mm (") Truck height mm (43' 1/4") Overall length Workg area 36 Gross Axle Weight Ratg, Front 72 kg (20,000 lb) Gross Axle Weight Ratg, Rear kg (66,000 lb) Gross Vehicle Weight Ratg, Pusher kg (8,000 lb) Gross Vehicle Weight Ratg, Pusher kg (8,000 lb) Gross Vehicle Weight Ratg, Tag 3629 kg (8,000 lb) Wheelbase (WB) 744 cm (293 ) Cab to Axle/Cab to Trunnion (CA/CT) Frame Strength Frame Section Modulus (SM); front axle to end of AF Stability Weight, Front Stability Weight, Rear 8 cm (200 ) 7 MPa (110,000 PSI): 327 cm3 (20 3) 5341 kg (11,7 lb)* 31 kg (13,2 lb)* *NOTE: Estimated axles scale weights prior to stallation of crane assembly for % stability. Series NBT 9
10 Dimensions 17 mm (") AUX HOIST (OPTIONAL) 2946 mm (116") 1276 mm (") ROTATION 649 mm (26") 764 mm (30") FRONT LIFTING LUGS 2 mm (18") S/S HYD RESERVOIR 7,9 m - 13,7 m (26'-') TWO SECTION BOOM EXTENSION TABLE AT and 3 (OPTIONAL) REAR LIFTING LUGS BOLTED STRUCTURAL BUMPER ATTACHED TO TRUCK FRAME m ) WIDTH 2126 mm (84") AUX HOIST 1542 mm (61") MAIN HOIST 9730 mm (383") RETRACTED mm (1534") EXTENDED (SINGLE PART ROPEFALL) 17 mm (") AUX HOIST (OPTIONAL) 71 mm (141") 1942 mm (76") CHASSIS CAB CLEARANCE STANDARD CAB A/C 649 mm (26") 764 mm (30") CLAMPED STUD CONNECTION (FRONT ONLY) REAR WELDED/BOLTED LIFTING SHEAR PLATE LUGS CONNECTION 4314 mm (1") 7258 mm (286") 2591 mm (102") OVERALL WIDTH AUX HOIST (OPTIONAL) 17 mm (") S/S HYD RESERVOIR 637 mm (25") 2 mm (18") 3X WELDED/BOLTED FLEX PLATE CONNECTION 3301 mm (130") ROTATION BOLTED STRUCTURAL BUMPER ATTACHED TO TRUCK FRAME 296 mm (12") 2946 mm (116") 9730 mm (383") RETRACTED mm (1534") EXTENDED (SINGLE PART ROPE 649 mm (26") 764 mm (30") 31 mm (144") S/S HYD RESERVOIR 1276 mm (") ROTATION 71 mm (141") 2946 mm (116") 1276 mm (") ROTATION FRONT LIFTING LUGS 2 mm (18") 1942 mm (76") CHASSIS CAB CLEARANCE 7,9 m - 13,7 m (26'TWO SECTION BO TABLE AT (OPTIONAL) REAR LIFTING LUGS BOLTED STRUCTURAL BUMPER ATTACHED TO TRUCK FRAME 0 mm (") MAX CHASSIS WIDTH 2591 mm (102") OVERALL WIDTH CLAMPED STUD CONNECTION (FRONT ONLY) 4314 mm (1") 9730 mm (383") RETRACTED mm (1534") EXTENDED (SINGLE PART ROPEFALL) 1542 MA 1942 mm (76") STA mm (141")
11 Dimensions 3301 mm (130") RET/MID/EXT 4813 mm (189") EXTENDED 43 mm (173") MID-SPAN 7388 mm (291") EXT 4886 mm (192") MID 2384 mm (94") RET 37 mm (156") RETRACTED 2387 mm (94") RET 4738 mm (187") MID 89 mm (279") EXT HORIZ CG SEE TABLE Series NBT 11
12 Workg range NBT: 39,0 m (128 ft boom) with 7,9 m - 13,7 m (26 ft - ft) extension (heavy lift) (Boom deflection not shown) Offset Offset ' Ext. 26' Ext. 1 Height from ground Boom length and extension Max boom angle Axis of rotation Operatg radius from axis of rotation (6' 9") (8' 7") Dimensions are for largest furnished hook block and headache ball with anti-two block activated. *This drawg shows the physical reach of the mache. Always refer to the load chart to see which portions of this diagram are valid for the specific mache configuration and where the loads are structurally or stability limited. 12
13 NBT: 39,01 m (128 ft) boom, 2722 kg (00 lb) countwerweight, 36, outriggers % extended, (heavy lift) # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,000 (68.1) 94,1 (64.0) 82,8 69,7 53,1 (.3) 36,0 (21.8) (68.5) (64.1) (56.2) 43,0 (47.6),0 (37.4) 26,0 (23.6) (73.3) (.0) 47,9 (64.2) 43,0 (58.0) 36,0 (51.3) 29,0 (43.9) 23,300 (.3) 18,0 (24.0) 49,5 46,0 41,0 (68.8) 37,1 33,0 (58.7) 30, (53.2) 23,6 (47.1) 19,1 (.3) 15,0 (32.5) 13,2 (22.2) 39,300 34, (72.5) 30, 27, (64.2) 24,0 22,7 (.2) 19,0 (.2) 16, (44.7) 13,0 (38.7) 11,0 (31.7) 90 (23.9) *71 (9.4) 27,200 (78.3) 25,200 (.0) 22,6 (71.6) 20,0 (68.0) 18,0 (64.3) 17,0 15,0 (56.5) 14,0 (52.4) 13,6 (47.9) 11,6 (43.0) 10, (38.1) (31.9) (24.4) (13.0) 21,000 (77.2) 19,0 (74.2) 17,0 (71.2) 16,300 (68.0) 15, (64.8) 14,000 (61.5) 12,8 (58.0) 12,000 (54.4) 11,2 (.9) 10,300 (46.8) 80 (42.3) 70 (37.4) 60 (31.7) 50 (25.0) (15.5) Mimum boom angle ( ) for dicated length Maximum boom length (ft.) at boom angle NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #LMI operatg code. Refer to LMI manual for operatg structions. Liftg capacities at zero degree boom angle Boom angle 16,0 (76.2) 15,7 14,0 13,6 (68.0) 12,5 (.0) 11,7 (62.0) 10,9 (59.2) 10,300 (56.0) (52.6) (49.0) 78 (.0) 60 (.7) 59 (36.0) (30.7) 00 (24.2) 30 (15.2) A 54-B 64-C -D 86-E 97-F 107-G 17,9 (27.5) 10,000 (38.8) 68 (49.8) (81.8) 17 (92.8) 0 (102.8) 13,0 (77.8) 13,0 (.6) 12,0 (73.2) 12,0 11,300 (68.2) 10,6 (.9) 10,000 (63.2) (.4) 88 (57.5) (54.5) 79 (51.3) 69 (47.8) (44.1) 5300 (.1) 40 (.7) 00 (30.8) 00 (24.9) (17.0) (74.9) (72.8) (.6) 87 (66.0) 78 (63.4) 00 (.7) 6300 (57.9) 50 (.1) 51 (52.1) 46 (49.0) 41 (.7) (42.2) 3300 (38.4) (34.3) 26 (29.6) 10 (23.8) 1 (15.9) 1 1 NOTE: ( ) Reference radii Series NBT 13
14 NBT: 39,01 m (128 ft) boom, 2722 kg (00 lb) countwerweight, over rear, outriggers % extended, (heavy lift) # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,000 (68.1) 94,1 (64.0) 82,8 69,7 53,1 (.3) 36,0 (21.8) (68.5) (64.1) (56.2) 43,0 (47.6),0 (37.4) 26,0 (23.6) (73.3) (.0) 47,9 (64.2) 43,0 (58.0) 36,0 (51.3) 30,9 (43.9) 25,0 (.3) 19,9 (24.1) 49,5 46,0 41,0 (68.8) 37,1 33,0 (58.7) 30,0 (53.2) 26,0 (47.1) 22,5 (.4) 18,9 (32.6) *15, (22.3) 39,300 34, (72.5) 30, 27, (64.2) 24,0 22,7 (.2) 21,200 (.3) 19,2 (44.9) 16,0 (38.9) 14, (31.9) *12,200 (24.0) *71 (9.4) 27,200 (78.3) 25,200 (.0) 22,6 (71.6) 20,0 (68.0) 18,0 (64.3) 17,0 15,0 (56.5) 14,0 (52.4) 13,6 (47.9) 12,7 (43.1) 12,000 (37.7) 11,000 (32.2) 96 (24.6) *60 (13.1) 21,000 (77.2) 19,0 (74.2) 17,0 (71.2) 16,300 (68.0) 15, (64.8) 14,000 (61.5) 12,8 (58.0) 12,000 (54.4) 11,2 (.9) 10,0 (46.8) 10,0 (42.5) (37.6) (32.1) 70 (25.3) *59 (15.6) Mimum boom angle ( ) for dicated length Maximum boom length (ft.) at boom angle NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #LMI operatg code. Refer to LMI manual for operatg structions. Liftg capacities at zero degree boom angle Boom angle 16,0 (76.2) 15,7 14,0 13,6 (68.0) 12,5 (.0) 11,7 (62.0) 10,9 (59.2) 10,300 (56.0) (52.6) 9200 (49.0) (.2) 8300 (41.0) 78 (36.5) 69 (31.1) 6200 (24.7) *47 (15.4) A 54-B 64-C -D 86-E 97-F 107-G 17,9 (27.5) 10,000 (38.8) 68 (49.8) (81.8) 17 (92.8) 0 (102.8) 13,0 (77.8) 13,0 (.6) 12,0 (73.2) 12,0 11,300 (68.2) 10,6 (.9) 10,000 (63.2) (.4) 88 (57.5) (54.5) 79 (51.3) (48.0) 72 (44.5) 69 (.5) 6300 (36.3) 56 (31.4) 00 (25.5) *4200 (17.3) (74.9) (72.8) (.6) 87 (66.0) 78 (63.4) 00 (.7) 6300 (57.9) 50 (.1) 51 (52.1) 46 (49.0) 41 (.7) (42.2) 3300 (38.4) (34.3) 26 (29.6) 10 (23.8) 1 (15.9) 1 1 NOTE: ( ) Reference radii
15 NBT: 7,9 m (26 ft) fixed and 7,9 m - 13,7 m (26 ft - ft) offsettable extension, 2722 kg (00 lb) counterweight, 36, outriggers % extended, (heavy lift) **26 ft LENGTH ft LENGTH #0005 #0007 #0009 #0011 (.3) (71.9) (.1) (66.7) 48 (64.7) 00 (62.6) (58.3) 30 (56.1) 36 (53.8) 31 (51.2) 20 (48.4) 2 (.5) 10 (42.5) 10 (39.3) 9 (.8) 6 (32.1) 3 (77.4) (.6) (73.7) 46 (69.7) 40 (67.5) 41 (.2) 00 (62.9) (58.1) 30 (.4) 20 (52.5) 25 (49.5) 21 (46.3) 16 (42.7) 1200 (38.9) 8 (34.8) 0 (30) (77.3) (.8) (74.4) (72.9) (69.9) (66.9) (.4) (61.9) 32 (59.9) (57.8) 20 (.6) (53.5) 2,300 (51.2) 20 (48.7) 17 (46.0) 10 (43.3) 1200 (.4) 0 (37.2) 6 (33.9) 3 (77.0) (.2) (69.8) (67.9) (.9) 20 (61.7) 20 (59.5) 20 (57.1) 2300 (54.7) 22 (52.1) 2000 (49.1) 17 (.9) 10 (42.3) 0 (38.2) 0 (33.9) M. boom angle for dicated length Max. boom length at boom angle 64 ft 64 ft NOTE: ( ) Boom angles are degrees #LMI operatg code. Refer to LMI manual for structions. *Loads are structurally limited. **26 ft capacities are applicable to both 26 ft fixed and 26 ft tele extension. BOOM EXTENSION CAPACITY NOTES: 1. All capacities above the bold le are based on structural strength limitations ft and ft extension lengths may be used for sgle le liftg service. 3. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 4. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. Series NBT 15
16 NBT: 7,9 m (26 ft) fixed and 7,9 m - 13,7 m (26 ft - ft) offsettable extension, 2722 kg (00 lb) counterweight, over rear, outriggers % extended, (heavy lift) M. boom angle for dicated length Max. boom length at boom angle **26 ft LENGTH ft LENGTH #0006 #0008 #0010 #0012 (.3) (71.9) (.1) (66.7) 48 (64.7) 00 (62.6) (58.3) 30 (56.1) 3,6 (53.8) 31 (51.2) 20 (48.4) 2 (.5) 10 (42.5) 10 (39.3) 9 (.8) 6 (32.1) 3 (77.4) (.6) (73.7) 46 (69.7) 40 (67.5) 41 (.2) 00 (62.9) (58.1) 30 (.4) 20 (52.5) 25 (49.5) 21 (46.3) 16 (42.7) 1200 (38.9) 8 (34.8) 0 (30) (77.3) (.8) (74.4) (72.9) (69.9) (66.9) (.4) (61.9) 32 (59.9) (57.8) 20 (.6) (53.5) 2300 (51.2) 20 (48.7) 17 (46.0) 10 (43.3) 1200 (.4) 0 (37.2) 6 (33.9) 3 (77.0) (.2) (69.8) (67.9) (.9) 20 (61.7) 2,0 (59.5) 20 (57.1) 2300 (54.7) 22 (52.1) 2000 (49.1) 17 (.9) 10 (42.3) 0 (38.2) 0 (33.9) ft 64 ft NOTE: ( ) Boom angles are degrees #LMI operatg code. Refer to LMI manual for structions. *Loads are structurally limited. **26 ft capacities are applicable to both 26 ft fixed and 26 ft tele extension. BOOM EXTENSION CAPACITY NOTES: 1. All capacities above the bold le are based on structural strength limitations ft and ft extension lengths may be used for sgle le liftg service. 3. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 4. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. 16
17 NBT: 39,01 m (128 ft) boom, 2722 kg (00 lb) counterweight, 36, outriggers % extended, (heavy lift) # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,000 (68.1) 94,1 (64.0) 82,8 69,7 38,200 (.2) 24,0 (21.8) (68.5) (64.1) 39,0 (56.2) 25,0 (47.5) 18,0 (37.3) 13,7 (23.6) (73.3) (.0),000 (64.1) 26,0 (57.8) 19,000 (51.1) 14,300 (43.7) 11,0 (36.0) 86 (25.2) 49,5 46,0,0 (68.8) 26,7 (63.7) 19,300 (58.4) 14,0 (52.8) 11,0 (46.7) 89 (.7) 7200 (33.0) 57 (23.2) 39,300 34, (72.5) 27, (68.3) 19,0 14,8 (59.4) 11,0 (54.6) 91 (.1) (44.8) 00 (38.9) (32.1) 38 (23.6) (9.2) 27,200 (78.3) 25,200 (.0) 22,6 (71.6) 19,8 (67.9) 15, (64.1) 11,7 (.2) (56.5) 76 (52.2) 61 (47.7) 00 (42.9) 00 (37.5) 3200 (31.4) (23.9) 18 (12.6) 21,000 (77.2) 19,0 (74.2) 17,0 (71.2) 15,0 (67.9) 12,000 (64.5) (61.3) 70 (57.7) 6300 (54.0) 51 (.1) 41 (.9) 3300 (41.4) 20 (36.5) 2000 (30.9) 10 (24.2) 0 (14.8) 16,0 (76.2) 15,7 14,0 12,200 (67.8) (64.9) 79 (61.7) (58.4) 52 (.0) 42 (51.5) 30 (47.8) 20 (43.8) 2 (39.6) 10 (34.9) 1 (29.6) 0 (23.3) 13,0 (77.8) 13,0 (.6) 12,0 (73.2) 12,0 90 (68.2) 8 (.3) 60 (62.4) (59.4) 40 (56.3) 20 (49.8) 2200 (46.3) 16 (42.7) 1200 (38.7) 0 (34.4) (74.9) (72.8) (.6) 8300 (68.1) 67 (.4) 50 (62.6) 00 (59.9) 36 (57.0) 20 (54.1) 2300 (51.0) 17 (47.9) 12 (44.5) 8 (41.0) Mimum boom angle ( ) for dicated length Maximum boom length (ft) at boom angle 97 NOTE: ( ) Boom angles are degrees. #LMI operatg code. Refer to LMI manual for operatg structions. Liftg capacities at zero degree boom angle Boom angle A 54-B 64-C -D 86-E 97-F 17,9 (27.5) 10,000 (38.8) 68 (49.8) (81.8) 7 (92.8) NOTE: ( ) Reference radii Series NBT 17
18 NBT: 7,9 m (26 ft) fixed and 7,9 m - 13,7 m (26 ft - ft) offsettable extension, 2722 kg (00 lb) countwerweight, 36, outriggers % extended, (heavy lift) **26 ft LENGTH ft LENGTH #05 #07 #09 #0411 (.3) (71.9) (.1) 4300 (66.1) (61.5) 2000 (59.1) 10 (56.7) 9 (54.2) 5 (51.7) 3 (77.4) (.6) (73.7) (69.5) 30 (66.8) 20 (64.2) 21 (61.5) 15 (58.8) 10 (56.1) 0 (53.2) (77.3) (.8) (74.4) (72.9) (69.9) (66.9) 30 (64.5) 20 (62.3) 18 (.1) 10 (57.8) 9 (.5) 0 (53.2) 3 (77.0) (.2) (69.8) (67.9) 20 (.7) 10 (63.1) 10 (.4) 0 (57.8) 0 (.1) M. boom angle for dicated length Max. boom length at boom angle 64 ft 64 ft NOTE: ( ) Boom angles are degrees #LMI operatg code. Refer to LMI manual for structions. *Loads are structurally limited. **26 ft capacities are applicable to both 26 ft fixed and 26 ft tele extension. BOOM EXTENSION CAPACITY NOTES: 1. All capacities above the bold le are based on structural strength limitations ft and ft extension lengths may be used for sgle le liftg service. 3. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 4. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. 18
19 NBT: 39,01 m (128 ft) boom, 2722 kg (00 lb) counterweight, 36, outriggers 0% extended, (heavy lift) # A 54-B 64-C -D 86-E 97-F 107-G 118-H 128,0 (68.1) 48,300 (64.0) 34,0 23,300 13,7 (.2) 86 (24.2) 49,5,6 24,2 (64.0) 14,0 (56.1) (48.3) (38.3) 40 (25.2) 36,2 (73.2) 24,7 (69.8) 15, 10,000 (58.3) 69 (51.6) (44.3) 3200 (.9) 2000 (25.1) 36,7 (76.2) 25,1 (73.3) 15,0 10,2 72 (58.6) 00 (47.2) 2300 (.5) 10 (32.9) 5 (23.0) 25,0 (76.1) 15,6 (71.9) 10,0 (68.1) 52 (59.4) 36 (54.8) 20 (49.8) 15 (44.5) 0 (38.6) 25,8 (78.3) 15,0 (74.6) 10,6 (71.3) (67.6) 30 (.0) 20 (56.0) 16 (51.8) 0 (47.3) 16,200 10,8 (73.9) 70 (.7) (67.4) 39 (64.0) 27 (.6) 10 (57.0) 0 (53.3) 11, (.9) 79 (72.9) 50 (69.9) (66.9) (.7) 1 (57.5) 11,300 (77.5) 8 (.0) 58 (72.3) 4200 (69.6) 29 (66.8) 19 (64.0) 1200 (61.1) 5 (58.2) Mimum boom angle ( ) for dicated length Maximum boom length (ft) at boom angle 54 NOTE: ( ) Boom angles are degrees. #LMI operatg code. Refer to LMI manual for operatg structions. Liftg capacities at zero degree boom angle Boom angle A 54-B 7300 (27.5) (38.8) 10 (49.8) 8300 (76.7) 59 (74.1) 4300 (71.6) (69.0) 20 (66.5) 12 0 (61.2) NOTE: ( ) Reference radii Series NBT 19
20 NBT: 39,01 m (128 ft) boom, 1361 kg ( lb) counterweight, 36, outriggers % extended, (heavy lift) # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,000 (68.1) 94,1 (64.0) 82,8 69,7 53,1 (.3) 36,0 (21.8) (68.5) (64.1) (56.2) 43,0 (47.6),0 (37.4) 26,0 (23.6) (73.3) (.0) 47,9 (64.2) 43,0 (58.0) 36,0 (51.3) 27,300 (43.9) 21,0 (.2) 17,1 (24.0) 49,5 46,0 41,0 (68.8) 37,1 33,0 (58.7) 27,0 21,0 (47.0) 17,0 (.3) 14,0 (32.4) 11,9 (22.2) 39,300 34, (72.5) 30, 27, (64.2) 24,0 22,000 (.1) 17,7 (.1) 14,6 (44.6) 12,200 (38.6) 10,0 (32.4) 88 (23.9) *71 (9.4) 27,200 (78.3) 25,200 (.0) 22,6 (71.6) 20,0 (68.0) 18,0 (64.3) 17,0 15,0 (56.5) 14,0 (52.4) 12,0 (47.8) 10,0 (43.4) (38.0) 77 (31.8) 66 (24.3) 50 (13.0) Mimum boom angle ( ) for dicated length Maximum boom length (ft) at boom angle NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #LMI operatg code. Refer to LMI manual for operatg structions. Boom angle 21,000 (77.2) 19,0 (74.2) 17,0 (71.2) 16,300 (68.0) 15, (64.8) 14,000 (61.5) 12,8 (58.0) 12,000 (54.4) 10,0 (.8) 92 (46.6) 70 (42.1) 60 (37.2) 50 (31.6) (24.9) 40 (15.4) Liftg capacities at zero degree boom angle 16,0 (76.2) 15,7 14,0 13,6 (68.0) 12,5 (.0) 11,7 (62.0) 10,9 (59.2) 10,300 (56.0) (52.5) (48.8) 69 (44.8) 00 (.5) (.8) 40 (30.5) 38 (24.1) 32 (15.0) A 54-B 64-C -D 86-E 97-F 107-G 17,9 (27.5) 10,000 (38.8) 68 (49.8) (81.8) 17 (92.8) 0 (102.8) 13,0 (77.8) 13,0 (.6) 12,0 (73.2) 12,0 11,300 (68.2) 10,6 (.9) 10,000 (63.2) (.4) 88 (57.5) 8200 (54.4) 7 (51.1) 61 (47.6) 5300 (43.8) 40 (39.9) 39 (.5) 30 (30.6) 20 (24.7) 20 (16.8) (74.9) (72.8) (.6) 87 (66.0) 78 (63.4) 00 (.7) 6300 (57.9) 50 (.1) 51 (52.1) 46 (49.0) 41 (.7) (42.2) 3300 (38.4) 29 (34.3) (29.5) *10 (23.8) *1 (15.9) NOTE: ( ) Reference radii
21 NBT: 39,01 m (128 ft) boom, 1361 kg ( lb) counterweight, over rear, outriggers % extended, (heavy lift) # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,000 (68.1) 94,1 (64.0) 82,8 69,7 53,1 (.3) 36,0 (21.8) (68.5) (64.1) (56.2) 43,0 (47.6),0 (37.4) 26,0 (23.6) (73.3) (.0) 47,9 (64.2) 43,0 (58.0) 36,0 (51.3) 30,9 (43.9) 25,1 (.3) *19,9 (24.1) 49,5 46,0 41,0 (68.8) 37,1 33,0 (58.7) 30,0 (53.2) 25,0 (47.1) 20,9 (.4) 17,5 (32.5) 14,8 (22.3) 39,300 34, (72.5) 30, 27, (64.2) 24,0 22,7 (.2) 21,200 (.3) 17,0 (44.8) 15, (38.8) 13,000 (31.8) 11,200 (24.0) *71 (9.4) 27,200 (78.3) 25,200 (.0) 22,6 (71.6) 20,0 (68.0) 18,0 (64.3) 17,0 15,0 (56.5) 14,0 (52.4) 13,6 (47.9) 12,7 (43.1) 11,0 (37.7) 10,0 (32.1) 80 (24.5) *60 (13.1) 21,000 (77.2) 19,0 (74.2) 17,0 (71.2) 16,300 (68.0) 15, (64.8) 14,000 (61.5) 12,8 (58.0) 12,000 (54.4) 11,2 (.9) 10,0 (46.8) 10,0 (42.5) 89 (37.6) 70 (31.9) 69 (25.2) *59 (15.6) Mimum boom angle ( ) for dicated length Maximum boom length (ft ) at boom angle NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #LMI operatg code. Refer to LMI manual for operatg structions. Liftg capacities at zero degree boom angle Boom angle 16,0 (76.2) 15,7 14,0 13,6 (68.0) 12,5 (.0) 11,7 (62.0) 10,9 (59.2) 10,300 (56.0) (52.6) 9200 (49.0) (.2) 00 (41.0) 7 (36.3) 62 (30.9) (24.5) *47 (15.4) A 54-B 64-C -D 86-E 97-F 107-G 17,9 (27.5) 10,000 (38.8) 68 (49.8) (81.8) 17 (92.8) 0 (102.8) 13,0 (77.8) 13,0 (.6) 12,0 (73.2) 12,0 11,300 (68.2) 10,6 (.9) 10,000 (63.2) (.4) 88 (57.5) (54.5) 79 (51.3) (48.0) 7200 (44.5) (.5) 56 (36.1) 00 (31.1) 40 (25.2) 30 (17.3) (74.9) (72.8) (.6) 87 (66.0) 78 (63.4) 00 (.7) 6300 (57.9) 50 (.1) 51 (52.1) 46 (49.0) 41 (.7) (42.2) 3300 (38.4) (34.3) 26 (29.6) 10 (23.8) 1 (15.9) 1 1 NOTE: ( ) Reference radii Series NBT 21
22 NBT: 7,9 m (26 ft) fixed and 7,9 m - 13,7 m (26 ft - ft) offsettable extension, 1361 kg ( lb) counterweight, 36, outriggers % extended, (heavy lift) **26 ft LENGTH ft LENGTH #5 #7 #9 #1011 (.3) (71.9) (.1) (66.7) 48 (64.7) 00 (62.6) (58.3) 30 (56.1) 36 (53.8) 31 (51.2) 20 (48.4) 2 (.5) 10 (42.5) 10 (39.3) 9 (.8) 6 (32.1) 3 (77.4) (.6) (73.7) 46 (69.7) 40 (67.5) 41 (.2) 00 (62.9) (58.1) 30 (.4) 20 (52.5) 25 (49.5) 21 (46.3) 16 (42.7) 1200 (38.9) 8 (34.8) 0 (30) (77.3) (.8) (74.4) (72.9) (69.9) (66.9) (.4) (61.9) 32 (59.9) (57.8) 20 (.6) (53.5) 2300 (51.2) 20 (48.7) 17 (46.0) 10 (43.3) 1200 (.4) 0 (37.2) 6 (33.9) 3 (77.0) (.2) (69.8) (67.9) (.9) 20 (61.7) 20 (59.5) 20 (57.1) 2300 (54.7) 22 (52.1) 2000 (49.1) 10 (.6) *10 (42.3) *0 (38.2) *0 (33.9) M. boom angle for dicated length Max. boom length at boom angle 64 ft 64 ft NOTE: ( ) Boom angles are degrees. *Loads are structurally limited #LMI operatg code. Refer to LMI manual for structions. **26 ft capacities are applicable to both 26 ft fixed and 26 ft tele extension. BOOM EXTENSION CAPACITY NOTES: 1. All capacities above the bold le are based on structural strength limitations ft and ft extension lengths may be used for sgle le liftg service. 3. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 4. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. 22
23 NBT: 7,9 m (26 ft) fixed and 7,9 m - 13,7 m (26 ft - ft) offsettable extension, 1361 kg ( lb) counterweight, over rear, outriggers % extended, (heavy lift) **26 ft LENGTH ft LENGTH #6 #8 #1010 #1012 (.3) (71.9) (.1) (66.7) 48 (64.7) 00 (62.6) (58.3) 30 (56.1) 36 (53.8) 31 (51.2) 20 (48.4) 2 (.5) 10 (42.5) 10 (39.3) 9 (.8) 6 (32.1) 3 (77.4) (.6) (73.7) 46 (69.7) 40 (67.5) 41 (.2) 00 (62.9) (58.1) 30 (.4) 20 (52.5) 25 (49.5) 21 (46.3) 16 (42.7) 1200 (38.9) 8 (34.8) 0 (30) (77.3) (.8) (74.4) (72.9) (69.9) (66.9) (.4) (61.9) 32 (59.9) (57.8) 20 (.6) (53.5) 2300 (51.2) 20 (48.7) 17 (46.0) 10 (43.3) 1200 (.4) 0 (37.2) 6 (33.9) 3 (77.0) (.2) (69.8) (67.9) (.9) 20 (61.7) 20 (59.5) 20 (57.1) 2300 (54.7) 22 (52.1) 2000 (49.1) 17 (.9) 10 (42.3) 0 (38.2) 0 (33.9) M. boom angle for dicated length Max. boom length at boom angle 64 ft 64 ft NOTE: ( ) Boom angles are degrees #LMI operatg code. Refer to LMI manual for structions. **26 ft capacities are applicable to both 26 ft fixed and 26 ft tele extension. BOOM EXTENSION CAPACITY NOTES: 1. All capacities above the bold le are based on structural strength limitations ft and ft extension lengths may be used for sgle le liftg service. 3. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 4. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. Series NBT 23
24 NBT: 39,01 m (128 ft) boom, 1361 kg ( lb) counterweight, 36, outriggers % extended, (heavy lift) # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,000 (68.1) 94,1 (64.0) 82,8 64,200 34,6 (.2) 22,2 (21.8) (68.5) (64.1),7 (56.2) 23,0 (47.5) 16,5 (37.3) 12,1 (23.6) (73.3) (.0) 36,0 (64.1) 23,0 (57.8) 17,0 (51.1) 12,0 (43.7) (36.0) (25.2) 49,5 46,0 36,8 (68.8) 24,300 (63.6) 17,0 (58.3) 13,000 (52.7) 10,000 (47.3) 70 (.7) 6200 (33.0) 48 (23.2) 39,300 34, (72.5) 24,6 (68.2) 17,0 13,2 (59.3) 10,200 (.0) 81 (.1) (44.8) 5 (38.8) 00 (32.0) 3 (23.5) 2300 (9.1) 27,200 (78.3) 25,200 (.0) 22,6 (71.6) 17,8 (67.8) 13,0 (64.0) 10,0 (.4) 8300 (56.4) 60 (52.1) 52 (47.6) 41 (42.8) 32 (37.4) (31.3) 18 (23.8) 12 (12.5) 21,000 (77.2) 19,0 (74.2) 17,0 (71.2) 13,0 (67.8) 10,0 (64.7) (61.2) 67 (57.6) (53.9) 4300 (49.9) 30 (.8) 20 (41.3) 19 (36.4) 10 (30.8) 0 (24.1) 0 (14.7) 16,0 (76.2) 15,7 13,9 (.7) 10,0 (67.8) (64.7) 60 (61.5) 50 (58.2) 40 (54.8) 00 (51.3) 20 (47.6) 20 (43.7) 10 (39.5) 0 (34.8) 0 (29.5) 13,0 (77.8) 13,0 (.6) 12,0 (73.2) 11, (67.9) (.1) 56 (62.1) (59.2) 30 (56.1) 20 (52.9) 21 (49.6) 10 (46.2) 1 (42.5) 6 (38.5) (74.9) (72.8) 88 (.4) 7200 (67.8) 50 (.1) 46 (62.4) (59.6) 20 (56.7) 22 (53.8) 16 (.8) 11 (47.6) 0 (44.3) Mimum boom angle ( ) for dicated length Maximum boom length (ft) at boom angle 86 NOTE: ( ) Boom angles are degrees. #LMI operatg code. Refer to LMI manual for operatg structions. Liftg capacities at zero degree boom angle Boom angle A 54-B 64-C -D 86-E 17,9 (27.5) 99 (38.8) 58 (49.8) (81.8) NOTE: ( ) Reference radii
25 NBT: 7,9 m (26 ft) fixed and 7,9 m - 13,7 m (26 ft - ft) offsettable extension, 1361 kg ( lb) countwerweight, 36, outriggers % extended, (heavy lift) **26 ft LENGTH ft LENGTH #15 #17 #19 #1411 (77.1) (.5) (73.8) (72.2) (.5) 40 (68.0) 00 (.8) 26 (63.5) 19 (61.1) 10 (58.8) 8 (56.3) 3 (77.4) (.6) (73.7) 47 (71.6) 37 (69.0) 28 (66.3) 21 (63.7) 10 (61.1) 0 (58.4) 0 (.7) (77.3) (.8) (74.4) (72.9) (69.9) (66.1) (61.7) 12 (59.6) 0 (57.3) 0 (.1) 3 (77.0) (.2) (69.8) 20 (67.7) 18 (.1) 10 (62.5) 0 (59.9) 0 (57.3) M. boom angle for dicated length Max. boom length at boom angle 64 ft 64 ft NOTE: ( ) Boom angles are degrees #LMI operatg code. Refer to LMI manual for structions. **26 ft capacities are applicable to both 26 ft fixed and 26 ft tele extension. BOOM EXTENSION CAPACITY NOTES: 1. All capacities above the bold le are based on structural strength limitations ft and ft extension lengths may be used for sgle le liftg service. 3. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 4. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only Series NBT 25
26 NBT: 39,01 m (128 ft) boom, 1361 kg ( lb) counterweight, 36, outriggers 0% extended, (heavy lift) #11 Ma noom length A 54-B 64-C -D 86-E 97-F 107-G 118-H ,0 (68.0) 42,0 (64.0) 30,200 20,0 11,0 (.2) 71 (24.2) 43,0 (71.3) 31,2 21,000 (64.0) 12,0 (56.1) 00 (48.3) 51 (38.3) 3200 (25.2) 31,8 (73.2) 21,5 (69.7) 12,8 (58.2) 50 (51.6) 36 (44.3) 22 (.9) 11 (25.1) 32,300 (76.1) 21,0 (73.2) 13,1 (68.3) 58 (58.6) 30 (47.1) 10 (.5) 5 (32.8) 22,200 (76.0) 13,0 (71.9) 87 (68.1) 4 (59.4) 26 (54.7) 10 (49.8) 7 (44.5) 22,5 (78.2) 13,6 (74.5) 89 (71.2) 6200 (67.6) (59.9) 17 (.9) 0 (51.7) 13,0 (76.7) 9 (73.8) (.5) 40 (67.3) (56.9) 9300 (.7) (72.8) 00 (69.8) 30 (66.8) 19 (63.7) 1 (.6) (77.5) 60 (74.8) 40 (72.1) 31 (69.4) 20 (66.6) 11 Mimum boom angle ( ) for dicated length Maximum boom length (ft) at 43 boom angle NOTE: ( ) Boom angles are degrees. #LMI operatg code. Refer to LMI manual for operatg structions. Liftg capacities at zero degree boom angle Boom angle A 57 (27.5) 19 (38.8) (73.9) 32 2 (68.8) 1200 (66.3) 0 (63.6) NOTE: ( ) Reference radii
27 NBT: 39,01 m (128 ft) boom, 0 kg (0 lb) counterweight, 36, outriggers % extended, (heavy lift) 8 # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,000 (68.1) ,1 (64.0) 82,8 69,7 53,1 (.3) 36,0 (21.8) (68.5) (64.1) (56.2) 43,0 (47.6) 31,0 (37.3) 23,0 (23.6) (73.3) (.0) 47,9 (64.2) 43,0 (58.0) 32,0 (51.3) 24,1 (43.8) 18,0 (.2) 14,0 (24.0) 49,5 46,0 41,0 (68.8) 37,1 33,000 (58.7) 24,0 (53.0) 19, (47.0) 15,2 (.2) 12,0 (32.4) 10,0 (23.3) 39,300 34, (72.5) 30, 27, (64.2) 24,0 19,0 (.0) 15,5 (.0) 12,0 (44.5) 10,6 (39.2) 80 (32.3) (23.8) 62 (9.3) 27,200 (78.3) 25,200 (.0) 22,6 (71.6) 20,0 (68.0) 18,0 (64.3) 17,0 15,7 (56.5) 12,0 (52.2) 10,8 (48.1) 9 (43.2) 76 (37.9) (31.7) 50 (24.2) 40 (12.9) 21,000 (77.2) 19,0 (74.2) 17,0 (71.2) 16,300 (68.0) 15, (64.8) 14,000 (61.5) 12,8 (58.0) 11,000 (54.6) 92 (.6) 70 (46.4) 66 (41.9) 56 (37.0) (31.4) (24.7) 30 (15.2) Mimum boom angle ( ) for dicated length Maximum boom length (ft) at boom angle NOTE: ( ) Boom angles are degrees. #LMI operatg code. Refer to LMI manual for operatg structions. Liftg capacities at zero degree boom angle Boom angle 16,0 (76.2) 15,7 14,0 13,6 (68.0) 12,5 (.0) 11,7 (62.0) 10,9 (59.2) (.8) 79 (52.2) 67 (48.5) 57 (44.5) 40 (.3) 41 (.6) 00 (30.3) 29 (23.8) 20 (14.8) A 54-B 64-C -D 86-E 97-F 107-G 17,9 (27.5) 10,000 (38.8) 6,8 (49.8) 6, 4,2 2,8 (81.8) 1,7 (92.8) 0 (102.8) 13,0 (77.8) 13,0 (.6) 12,0 (73.2) 12,0 11,300 (68.2) 10,6 (.9) 10,000 (63.2) (.4) 8 (57.3) 60 (54.1) 50 (.7) 00 (47.2) 42 (43.5) 30 (39.5) 30 (.2) (30.2) 20 (24.4) 10 (16.5) (74.9) (72.8) (.6) 87 (66.0) 78 (63.4) 00 (.7) 6300 (57.9) 50 (.1) 5 (52.1) 40 (48.9) (.5) 31 (42.0) 20 (38.1) 21 (33.9) 10 (29.2) 1300 (23.5) 9 (15.8) 1 1 NOTE: ( ) Reference radii. 05 Series NBT 27
28 NBT: 39,01 m (128 ft) boom, 0 kg (0 lb) counterweight,over rear, outriggers % extended, (heavy lift) # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,000 (68.1) 94,1 (64.0) 82,8 69,7 53,1 (.3) 36,0 (21.8) (68.5) (64.1) (56.2) 43,0 (47.6),0 (37.4) 26,0 (23.6) (73.3) (.0) 47,9 (64.2) 43,0 (58.0) 36,0 (51.3) 28,0 (43.9) 22,8 (.3) 18,6 (24.0) 49,5 46,0 41,0 (68.8) 37,1 33,0 (58.7) 29,1 (53.2) 23,200 (47.1) 19,000 (.3) 15,0 (32.5) 13,300 (22.2) 39,300 34, (72.5) 30, 27, (64.2) 24,0 22,7 (.2) 19,2 (.2) 16,0 (44.7) 13,0 (38.7) 11,0 (31.7) 10,0 (23.9) *71 (9.4) 27,200 (78.3) 25,200 (.0) 22,6 (71.6) 20,0 (68.0) 18,0 (64.3) 17,0 15,0 (56.5) 14,0 (52.4) 13,6 (47.9) 11,0 (43.0) 10,2 (38.1) 80 (32.0) 77 (24.4) *60 (13.1) 21,000 (77.2) 19,0 (74.2) 17,0 (71.2) 16,300 (68.0) 15, (64.8) 14,000 (61.5) 12,8 (58.0) 12,000 (54.4) 11,2 (.9) 10,0 (46.8) (42.3) 70 (37.4) 60 (31.8) (25.0) 52 (15.5) Mimum boom angle ( ) for dicated length Maximum boom length (ft) at boom angle NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #LMI operatg code. Refer to LMI manual for operatg structions. Liftg capacities at zero degree boom angle Boom angle 16,0 (76.2) 15,7 14,0 13,6 (68.0) 12,5 (.0) 11,7 (62.0) 10,9 (59.2) 10,300 (56.0) (52.6) 9200 (49.0) (.0) 00 (.8) 61 (36.1) (30.7) 40 (24.3) 4 (15.2) A 54-B 64-C -D 86-E 97-F 107-G 17,9 (27.5) 10,000 (38.8) NOTE: ( ) Reference radii. 68 (49.8) (81.8) 17 (92.8) 0 (102.8) 13,0 (77.8) 13,0 (.6) 12,0 (73.2) 12,0 11,300 (68.2) 10,6 (.9) 10,000 (63.2) (.4) 88 (57.5) (54.5) 79 (51.3) 71 (47.9) 62 (44.2) 50 (.2) 48 (.8) 4200 (30.8) (25.0) 3200 (17.1) (74.9) (72.8) (.6) 87 (66.0) 78 (63.4) 00 (.7) 6300 (57.9) 50 (.1) 51 (52.1) 46 (49.0) 41 (.7) (42.2) 3300 (38.4) (34.3) 26 (29.6) 10 (23.8) 1 (15.9)
29 NBT: 7,9 m (26 ft) fixed and 7,9 m - 13,7 m (26 ft - ft) offsettable extension, 0 kg (0 lb) countwerweight, 36, outriggers % extended, (heavy lift) M. boom angle for dicated length Max. boom length at boom angle **26 ft LENGTH ft LENGTH #05 #07 #09 #11 (.3) (71.9) (.1) (66.7) 48 (64.7) 00 (62.6) (58.3) (.8) 29 (53.2) 2,0 (.5) 19 (47.8) 10 (44.9) 11 (41.8) 7 (38.6) 0 (.1) 3 (77.4) (.6) (73.7) 46 (69.7) 40 (67.5) 41 (.2) 00 (62.9) 3,0 (57.8) 29 (54.9) 20 (51.9) 10 (48.8) 10 (.5) 10 (42.0) 6 (38.2) (77.3) (.8) (74.4) (72.9) (69.9) (66.9) (.4) (61.9) 32 (59.9) (57.8) 20 (.6) (.4) 10 (47.9) 12 (.2) 9 (42.4) 6 (39.5) 3 (77.0) (.2) (69.8) (67.9) (.9) 20 (61.7) 20 (59.5) 20 (57.1) 2200 (54.4) 10 (51.4) 10 (48.2) 10 (44.9) 0 (41.3) ft 64 ft NOTE: ( ) Boom angles are degrees #LMI operatg code. Refer to LMI manual for structions. **26 ft capacities are applicable to both 26 ft fixed and 26 ft tele extension. BOOM EXTENSION CAPACITY NOTES: 1. All capacities above the bold le are based on structural strength limitations ft and ft extension lengths may be used for sgle le liftg service. 3. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 4. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. Series NBT 29
30 NBT: 7,9 m (26 ft) fixed and 7,9 m - 13,7 m (26 ft - ft) offsettable extension, 0 kg (0 lb) countwerweight, over rear, outriggers % extended, (heavy lift) **26 ft LENGTH ft LENGTH #06 #08 #10 #12 (.3) (71.9) (.1) (66.7) 48 (64.7) 00 (62.6) (58.3) 30 (56.1) 36 (53.8) 31 (51.2) 20 (48.4) 2 (.5) 10 (42.5) 10 (39.3) 9 (.8) 6 (32.1) 3 (77.4) (.6) (73.7) 46 (69.7) 40 (67.5) 41 (.2) 00 (62.9) (58.1) 30 (.4) 20 (52.5) 25 (49.5) 21 (46.3) 16 (42.7) 1200 (38.9) 8 (34.8) 0 (30) (77.3) (.8) (74.4) (72.9) (69.9) (66.9) (.4) (61.9) 32 (59.9) (57.8) 20 (.6) (53.5) 2300 (51.2) 20 (48.7) 17 (46.0) 10 (43.3) 1200 (.4) 0 (37.2) 6 (33.9) 3 (77.0) (.2) (69.8) (67.9) (.9) 20 (61.7) 20 (59.5) 20 (57.1) 2300 (54.7) 22 (52.1) 2000 (49.1) 17 (.9) 10 (42.3) 0 (38.2) 0 (33.9) M. boom angle for dicated length Max. boom length at boom angle 64 ft 64 ft NOTE: ( ) Boom angles are degrees #LMI operatg code. Refer to LMI manual for structions. **26 ft capacities are applicable to both 26 ft fixed and 26 ft tele extension. BOOM EXTENSION CAPACITY NOTES: 1. All capacities above the bold le are based on structural strength limitations ft and ft extension lengths may be used for sgle le liftg service. 3. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 4. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only. 30
31 NBT: 39,01 m (128 ft) boom, 0 kg (0 lb) counterweight, 36, outriggers % extended, (heavy lift) # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,000 (68.1) 94,1 (64.0) 82,8 56,0 29,8 (.2) 18,8 (21.8) (68.5) (64.1) 31,000 (56.2) 19,9 (47.4) 13,0 (37.2) 10,000 (25.2) (73.3) (.0) 31,6 (64.0) 20,0 (57.7) 14,0 (51.1) 10,5 (44.4) 00 (36.0) 00 (25.2) 49,5 46,0 32, (68.7) 20,8 (63.6) 14,7 (58.3) 10,8 (53.3) 8300 (47.3) 6300 (.7) (33.0) 30 (23.1) Mimum boom angle ( ) for dicated length Maximum boom length (ft) at boom angle 39,300 32,5 (72.4) 21,200 (68.1) 15,000 (63.7) 11, (59.6) (.0) (.0) (44.7) 38 (38.8) 28 (32.0) 20 (23.5) 10 (9.1) 27,200 (78.3) 25,200 (.0) 21,0 (71.5) 15,2 (67.7) 11,300 (.3) 60 (56.3) (52.0) 00 (47.5) (42.7) 2200 (37.3) 15 (31.2) 9 (23.7) NOTE: ( ) Boom angles are degrees. #LMI operatg code. Refer to LMI manual for operatg structions. Boom angle 21,000 (77.2) 19,0 (74.2) 15,5 (71.0) 11,0 (67.6) 87 (64.5) 60 (61.0) (57.4) 41 (53.7) 31 (49.8) 20 (.6) 16 (41.2) 1 (36.3) 0 (30.7) Liftg capacities at zero degree boom angle A 54-B 64-C -D 15,0 (27.5) 70 (38.8) 00 (49.8) ,0 (76.2) 15,7 11,0 (.4) 80 (67.6) (64.5) 50 (61.3) 42 (58.0) 32 (54.6) 20 (51.1) 17 (47.4) 1200 (43.5) 0 (39.3) 13,0 (77.8) 13,0 (.6) 11,9 (73.1) 9 (.4) 7200 (67.6) 50 (64.8) 40 (61.9) 30 (58.9) 25 (.8) 18 (52.7) 12 (49.4) 7 (.9) (74.9) (72.8) (.1) 57 (67.4) 00 (64.7) (62.0) 26 (59.3) 1,9 (56.4) 10 (53.5) 8 (.5) NOTE: ( ) Reference radii Series NBT 31
32 NBT: 7,9 m (26 ft) fixed and 7,9 m - 13,7 m (26 ft - ft) offsettable extension, 0 kg (0 lb) countwerweight, 36, outriggers % extended, (heavy lift) Feet **26 ft LENGTH ft LENGTH # #87 #89 #8411 (.3) (71.9) 40 (69.8) 32 (67.5) 20 (.3) 16 (63.0) 10 (.7) 0 (58.3) 3 (77.4) (.6) (68.2) 10 (.7) 12 (63.1) 0 (77.3) (.8) (74.4) (72.9) 00 (69.7) 25 (67.4) 10 (.3) 10 (63.3) 0 (61.1) 0 (59) 3 (77.0) (.2) 20 (69.2) 15 (66.7) 10 (64.2) 0 (61.7) M. boom angle for dicated length Max. boom length at boom angle 64 ft 64 ft NOTE: ( ) Boom angles are degrees #LMI operatg code. Refer to LMI manual for structions. **26 ft capacities are applicable to both 26 ft fixed and 26 ft tele extension. BOOM EXTENSION CAPACITY NOTES: 1. All capacities above the bold le are based on structural strength limitations ft and ft extension lengths may be used for sgle le liftg service. 3. Radii listed are for a fully extended boom with the boom extension erected. For ma boom lengths less than fully extended, the rated loads are determed by boom angle. Use only the column which corresponds to the boom extension length and offset for which the mache is configured. For boom angles not shown, use the ratg of the next lower boom angle. WARNING: Operation of this mache with heavier loads than the capacities listed is strictly prohibited. Mache tippg with boom extension occurs rapidly and without advance warng. 4. Boom angle is the angle above or below horizontal of the longitudal axis of the boom base section after liftg rated load. 5. Capacities listed are with outriggers properly extended and vertical jacks set only 32
33 NBT: 39,01 m (128 ft) boom, 0 kg (0 lb) counterweight,36, outriggers 0% extended, (heavy lift) # A 54-B 64-C -D 86-E 97-F 107-G 118-H 128,6 (68.0),0 (64.0) 24,0 16,000 (41.6) 00 (24.2) 36,2 (71.3) 25,0 16,9 (56.9) 58 (48.3) 30 (38.3) 17 (25.2) Mimum boom angle ( ) for dicated length Maximum boom length (ft) at boom angle 26,300 (73.1) 17,0 (69.7) 10,0 (64.4) 6300 (58.2) 38 (51.6) 2200 (44.3) 9 (.9) 26,6 (76.0) 17,7 (73.1) 10,300 (68.8) 4 (58.6) 20 (53.0) 1200 (47.1) 18, (.9) 10,5 (72.2) 60 (68.0) 4300 (63.7) 26 (59.3) 10 (54.7) 0 (49.7) 18,0 (78.0) 10,0 (74.7) 6,9 (71.1) 40 (67.5) 27 (63.7) 15 (59.9) 0 (.8) 11,000 (76.8) (.4) 20 (67.1) 16 7 (.4) 7300 (.5) 47 (72.6) (69.6) 17 (66.6) 0 (63.6) (77.3) 48 (74.6) 3 (71.9) 18 (69.2) 0 (66.4) NOTE: ( ) Boom angles are degrees. #LMI operatg code. Refer to LMI manual for operatg structions. Liftg capacities at zero degree boom angle Boom angle A 30 (27.5) 0 (38.8) (76.1) (71.1) 9 (68.6) NOTE: ( ) Reference radii Series NBT 33
34 Workg range NBT: 39,0 m (128 ft boom) with 7,9 m - 13,7 m (26 ft - ft) extension (mimum truck) (Boom deflection not shown) 3 Offset Offset ' Ext. 26' Ext. 1 Height from ground Boom length and extension Max boom angle Axis of Operatg radius from axis of rotation rotation (6' 9") (8' 7") Dimensions are for largest furnished hook block and headache ball with anti-two block activated. *This drawg shows the physical reach of the mache. Always refer to the load chart to see which portions of this diagram are valid for the specific mache configuration and where the loads are structurally or stability limited. 34
35 NBT: 39,01 m (128 ft) boom, 2722 kg (00 lb) counterweight, 36, outriggers % extended, (mimum truck) # A 54-B 64-C -D 86-E 97-F 107-G 118-H ,000 (68.1) 94,1 (64) 82,8 69,7 53,1 (.3) 36,0 (21.8) (68.5) (64.1) (56.2) 43,0 (47.6),0 (37.4) 26,0 (23.6) (73.3) () 47,9 (64.2) 43,0 (58) 36,0 (51.3) 28, (43.9) 22,000 (.2) 17,0 (24) 49,5 46,0 41,0 (68.8) 37,1 33,0 (58.7) 28,0 22,0 (47) 18,0 (.3) 14,8 (32.4) 12,0 (22.2) 39,300 34, (72.5) 30, 27, (64.2) 24,0 22,0 (.2) 18,300 (.1) 15, (44.7) 12,6 (38.7) 10,0 (32.4) 9200 (23.9) *71 (9.4) 27,200 (78.3) 25,200 () 22,6 (71.6) 20,0 (68) 18,0 (64.3) 17,0 15,0 (56.5) 14,0 (52.4) 12,8 (47.8) 11,000 (43.4) (38) (31.9) 69 (24.3) 00 (13) Mimum boom angle ( ) for dicated length Maximum boom length (ft) at boom angle NOTE: ( ) Boom angles are degrees. *Loads are structurally limited. #LMI operatg code. Refer to LMI manual for operatg structions. Boom Angle 21,000 (77.2) 19,0 (74.2) 17,0 (71.2) 16,300 (68) 15, (64.8) 14,000 (61.5) 12,8 (58) 12,000 (54.4) 11,0 (.9) (46.7) 82 (42.2) 7 (37.3) 61 (31.7) 5300 (24.9) 40 (15.4) Liftg Capacities at Zero Degree Boom Angle Ma Boom Length Feet 16,0 (76.2) 15,7 14,0 13,6 (68) 12,5 () 11,7 (62) 10,9 (59.2) 10,300 (56) (52.6) (48.8) 72 (44.9) 62 (.6) (.9) 40 (30.6) (24.1) 00 (15.1) A 54-B 64-C -D 86-E 97-F 107-G 17,9 (27.5) 10,000 (38.8) 68 (49.8) (81.8) 17 (92.8) 0 (102.8) 13,0 (77.8) 13,0 (.6) 12,0 (73.2) 12,0 11,300 (68.2) 10,6 (.9) 10,000 (63.2) (.4) 88 (57.5) (54.5) (51.2) (47.6) (43.9) (39.9) 41 (.6) 30 (30.6) 3 (24.8) 20 (16.9) (74.9) (72.8) (.6) 87 (66) 78 (63.4) 00 (.7) 6300 (57.9) 50 (.1) 51 (52.1) 46 (49) 41 (.7) (42.2) 3300 (38.4) (34.3) 26 (29.6) 10 (23.8) 1 (15.9) NOTE: ( ) Reference radii Series NBT
Boom truck 55 tons. national nbt50/55. BOOM LENGTHS: 32 to 128 ft JIB LENGTHS: 26 to 45 ft JIB OFFSETS: 0-30
Boom truck tons national nbt/ BOOM LENGTHS: 32 to 128 ft JIB LENGTHS: 26 to 45 ft JIB S: 0-30 NOTES: National Crane Series NBT Product Guide ASME B30.5 Imperial % Features 31,1 m (102 ft) four-section
More informationNTC55 Product Guide. Features. ASME B30.5 Imperial 85% 49,9 t (55 USt) capacity at 2,44 m (8 ft)
NTC Product Guide ASME B30.5 Imperial % Features 49,9 t ( USt) capacity at 2,44 m (8 ft) 39,01 m (128 ft) five-section, full-power boom Hydraulically removable counterweight system with multiple configurations
More informationNational Crane Series NBT45 Product Guide
National Crane Series NBT45 Product Guide ASME B.5 Imperial 85% Features,8 t (45 USt) ratg 49,1 m (161 ft) five-section boom Self-lubricatg Easy Glide wear pads 41 kg ( lb) tailswg counterweight Features
More informationNational Crane Series NBT45 Product Guide
National Crane Series NBT45 Product Guide ASME B.5 Imperial 85% Features,8 t (45 USt) ratg 49,1 m (161 ft) five-section boom Self-lubricatg Easy Glide wear pads 41 kg ( lb) tailswg counterweight Features
More informationNational Crane Series NBT40
National Crane Series NBT40 Product Guide Features 36,3 t (40 USt) ratg 43,3 m (142 ft) five-section boom Self-lubricatg Easy Glide wear pads 862 kg (1900 lb) tailswg counterweight Features National Crane
More informationThree-position, out and down style outriggers with lighter polymeric floats
NBT-1 Capacity: USt (36,3 t) ratg Boom: 142 ft (43,3 m) five-section boom Max tip height ma boom: 1 ft (45,72 m) Max tip height ma boom with jib: 4 ft (62,2 m) Several boom length options providg work
More informationLOAD CHARTS NBT45 85% STABILITY ON OUTRIGGERS
LOAD CHARTS NBT45 85% STABILITY ON OUTRIGGERS 295995 SERIAL NUMBER 1 2 TABLE OF CONTENTS GENERAL NOTES...4-5 LIFTING AREA DIAGRAM / LINE PULLS & REEVING INFO / HOIST PERFORMANCE... 6 RANGE DIAGRAM w/ EXTENSION...7
More informationLOAD CHARTS NTC55 85% STABILITY ON OUTRIGGERS
LOAD CHARTS NTC 5% STABILITY ON OUTRIGGERS 0443 SERIAL NUMBER GA24146 1 TABLE OF CONTENTS GENERAL NOTES... 6-7 WT. REDUCTIONS / LINE PULLS & REEVING INFO / HOIST PERFORMANCE... LIFTING AREA DIAGRAM / BASKET
More informationBoom truck 36 tons. national series BOOM LENGTHS: 31ft to 127ft JIB LENGTHS: 31ft JIB OFFSETS:
Boom truck 3 tons national series : ft to 7ft JIB : ft JIB OFFSETS: NOTES: portland office: 53.23.11 seattle office: 2.74.4 features Why Buy a National Crane Series? 3 USt (32. t) Rating The provides a
More informationTMS500E. product guide. contents. features 40 ton (40 mt) Capacity. Truck Mounted Crane
TMS0E product guide features ton ( mt) Capacity 29 ft.-95 ft. (8.8-29 m) 4 section, full power sequenced synchronized boom 26 ft.- ft. (7.9-13.7 m) offsettable telescopic swingaway extension Optional 26
More informationTMS500E. product guide. contents. features 40 ton (40 mt) Capacity. Truck Mounted Crane
product guide features ton ( mt) Capacity 29 ft.-95 ft. (8.8-29 m) 4 section, full power synchronized boom 26 ft.- ft. (7.9-13.7 m) offsettable telescopic swingaway extension Optional 8,4 lb. (3837 kg)
More informationNational Crane Series NBT36
National Crane Series NBT36 Product Guide Features 32,7 t (36 USt) rating 38,7 m (127 ft) five-section boom Self-lubricating Easy Glide wear pads Features National Crane Series NBT36 32,7 t (36 USt) maximum
More informationNational Crane Series NBT30H
National Crane Series NBT30H Product Guide Features 27,2 t (30 USt) rating 33,52 m (110 ft) four-section boom All new design Multi-position Easy Reach control panel Graphical LMI Features National Crane
More informationRT535E. product guide. contents. features 35 ton (35 mt) capacity. Rough Terrain Hydraulic Crane. Features 2. Specifications 3.
product guide contents Features 2 features 35 ton (35 mt) capacity 32-102 ft. (9.8-31.0 m) 4-section full power boom 26-45 ft. (7.6-13.7 m) offsettable telescopic swingaway extension Dual-Axis electric
More informationGIUFFRE.COM. National Crane 500E2 Series GIUFFRE BROS CRANES INC. Product Guide
National Crane 5E2 Series Product Guide Features 16,3 t (18 USt) rating 21,6 m (71 ft) three-section boom Self-lubricating Easy Glide wear pads Internal anti-two block Features National Crane Series 5E2
More informationproduct guide contents features 40 ton (40 mt) Capacity Truck Mounted Crane 29 ft.-95 ft. ( m) 4 section, full power synchronized boom
product guide features ton ( mt) Capacity 29 ft.-95 ft. (8.8-29 m) 4 section, full power synchronized boom 26 ft.- ft. (7.9-13.7 m) offsettable telescopic swingaway extension Optional 8,4 lb. (3837 kg)
More informationROUGH TERRAIN HYDRAULIC CRANE RT875BXL
ROUGH TERRAIN HYDRAULIC CRANE RT875BXL Dimensions TAILSWING 14' (4280) 24' (7315) 10' 4" (31) TRACK 8' 4-1/2" (2553) 17' 4" (5283) 26' 6-1/2" (8090) 24' 11" (7595) 43' (13 106) 1' 3" (381) 7' 3" (2210)
More information24,000 lb. ( kg) counterweight with hydraulic removal system. Cummins ISM 450, six cylinder after cooled 450 hp (336 kw)
product guide features 41-128 ft. (12.6-39 m) 4 section full power Mega Form boom 33-56 ft. (10-17 m) manual offset bi-fold swingaway 2 x 20 ft. intermediate lattice inserts 24,000 lb. (10 886 kg) counterweight
More informationRT530E. product guide. contents. features 30 ton (30 mt) capacity. Rough Terrain Hydraulic Crane. Features 2. Specifications 3.
RT5E product guide contents Features 2 features ton ( mt) capacity 29-95 ft. (8.8-29 m) 4-section full power boom 26- ft. (7.9-13.7 m) telescopic swingaway extension Max main boom tip height of 2.5 ft.
More informationNational Crane Series NBT50
National Crane Series NBT50 Preliminary Product Guide Features 31,1 m (102 ft) four-section full power boom and optional 39,01 m (128 ft) five-section full power boom 45,36 t (50 USt) at 2,44 (8 ft) and
More informationGrove TMS700E. Product Guide. Features. 50 t or 55 t (50 USt or 60 USt) capacity
Grove TMS700E Product Guide Features 50 t or 55 t (50 USt or 60 USt) capacity 11 m 33,5 m (36 ft 1 ft) four-section, full power sequenced synchronized boom,1 m 17 m (33 ft 56 ft) offsettable bi-fold lattice
More information30' BOOM 13' 8" (4166) 24' BOOM 11' 8" (3556) 1' 8-1/2" (521) 3' 8-1/2" (1129) 15' 9-1/2" (4813) 17' 9-1/2" (5421)
INDUSTRIAL CRANE Dimensions 10' 10" (3302) 9' 4" (2845) 6' (1829) TRACK 7' (2134) A B 24' BOOM 11' 8" (3556) 1' 8-1/2" (521) 30' BOOM 13' 8" (4166) 3' 8-1/2" (1129) C 15' 9-1/2" (4813) 17' 9-1/2" (5421)
More informationNational Crane Series NBT50
National Crane Series NBT50 Preliminary Product Guide Features 31,1 m (102 ft) four-section full power boom and optional 39,01 m (128 ft) five-section full power boom 45,36 t (50 USt) at 2,44 (8 ft) and
More informationrough Terrain crane 60 tons
rough Terrain crane 60 tons grove rt700e BOOM LENGTHS: 36 to 110 ft JIB LENGTHS: 33 to 56 ft JIB OFFSETS: 0-25 - 45 NOTES: Specifications Superstructure Boom 11 m - 33,5 m (36 ft - 110 ft) four-section,
More informationNational Crane Series 800H
National Crane Series 8H Data Sheet Features 3,48 m (1 ft) four-section boom 2,86 t (23 USt) rating Self-lubricating Easy Glide wear pads Dimensions 85 mm (31.69") 247 mm (94.") Maximum transport width
More informationNational Crane Series NBT45
National Crane Series NBT45 Product Guide Features ř 40,8 t (45 USt) rating ř 43,3 m (142 ft) five-section boom ř Self-lubricating Easy Glide wear pads ř 2041 kg (4500 lb) tailswing counterweight Features
More informationDimensions Turning Radius (6.4m) 2 Wheel Steer /2 (3.6m) 4 Wheel Steer
INDUSTRIAL CRANE Dimensions Turng 20 11 (6.4m) 2 Wheel Steer 11 10-1/2 (3.6m) 4 Wheel Steer 14'0" 14 0 (4267) (4267) 12' 1-3/4" (3.7m) 7' 8-1/2" (2350) 6' 3-1/4" (1911) TAILSWING Note: ( ) Reference dimensions
More information600H Product Guide. Features. ASME B30.5 Imperial 85% Standard RCL System. 18,1 t (20 USt) rating
6H Product Guide ASME B3.5 Imperial 85% Features 18,1 t (2 USt) rating Five boom options available from 15 m (49 ft) to 27,42 m (9 ft) Multiple outrigger positions Standard RCL System Internal anti-two
More informationRT540E. product guide. contents. features. Rough Terrain Hydraulic Crane. Features 2. Specifications 3. Dimensions ton (35 mt) capacity
RT5E product guide contents Features 2 features ton ( mt) capacity 32 ft. - 2 ft. (9.8 m -31.0 m) 4-section, full power boom 26 ft. - ft. (7.9 m - 13.7 m) offsettable telescopic swing-away extension Full
More informationfeatures also available.
features 2 The boom on the is a 29-95 ft. (8.8-29 m) four-section full power boom with a maximum tip height of 2.5 ft. (31.2 m). This synchronized boom uses a single lever joystick control to extend boom
More informationTire Size 26.5 x 25 5' 5-1/2" (1661) 12' 2-1/4" (3715)
Dimensions 11' 13' 4" (64) TAILSWING 9' " (2997) OVER FENDERS 22' (66) FULL EXT 15' 9" (4801) MID EXT 9' 3-1/2" (2832) RET 9' 9-1/2" (2985) O/R A B C D E F G H 23.5 x 25 5' 4-1/4" (1631) 11' 11-1/2" (36)
More informationTECHNICAL SPECIFICATIONS
40142 40142 SIDE VIEW DIAGRAM Maximum Vertical Reach 207'/63,1 m Working Area 360 Degrees Lifting Capacity 80,000 lbs/36 287 kg Boom Length 142 /43,3 m Crane Weight (Standard) 40,300 lbs/18 280 kg Jib
More informationRT530E-2. product guide. contents. features. Rough Terrain Hydraulic Crane. Features 2. Specifications ton (27 mt) capacity.
RT5E-2 product guide contents Features 2 features ton (27 mt) capacity 29 ft. - 95 ft. (8.8 m -29.0 m) 4-section full power boom 26 ft. - ft. (7.9 m - 13.7 m) offsettable telescopic swing-away extension
More informationNational Crane Series NBT15
National Crane Series NBT15 Product Guide Features 13,4 t (15 USt) rating 18,3 m (60 ft) three-section boom Self-lubricating Easy Glide wear pads Internal anti-two block Load sense hydraulics Radio remote
More informationSeries 900A. product guide. contents. features. 103' Four-Section Boom. Features Ton Rating. Self-lubricating Easy Glide Wear Pads
Series 9A product guide features 13' Four-Section Boom 26 Ton Rating Self-lubricating Easy Glide Wear Pads Internal Anti-two-block contents Features 2 Mounting Configurations 3 Specifications 4 Capacities:
More information40142R TECHNICAL SPECIFICATIONS 40142R SIDE VIEW DIAGRAM. Maximum Vertical Reach. Powered Boom Sections 5 Overall Height. 210'/64 m Working Area
40142R 40142R SIDE VIEW DIAGRAM Maximum Vertical Reach 210'/64 m Working Area 360 Degrees Lifting Capacity 80,000 lbs/36 287 kg Boom Length 142 /43,3 m Crane Weight (Standard) 41,700 lbs/18 915 kg Jib
More informationWORKING RANGE DIAGRAM
Working Range Bi-fold Swingaway 36-110 ft. (11-33.5 m) 33-56 ft. (10.1-17.1 m) 12,1 lbs. (5511 kg) 100% 360 WORKING RANGE DIAGRAM 180 170 160 1 (BOOM DEFLECTION NOT SHOWN) 40 D6-829-101026 0 25 56' 33'
More informationNATIONAL MODEL 990A - 26 TON CAPACITY
LIFTING CHARTS - Boom Trucks NATIONAL MODEL 99A - 26 TON CAPACITY Load Chart Rating: Series 99A (27.4 m) Boom with 44 ft. (13.4 m) Jib 2ND JIB 44FT 1ST JIB 25FT LENGTH IN FEET 9 54 27-1 2 8 7 6 A B C D
More informationTMS x 4 & 6 x 6
TMS5 6 x 4 & 6 x 6 Dimensions 8' (2438) TAILSWING 11' 1" (3383) 7' 8" (2337) RET 13' 9-3/4" (4210) MID EXT ' (96) EXT Note: ( ) Reference dimensions in mm 16-3/4" (425) 43' 4" (13 8) OVERALL 10' 10" (32)
More informationView thousands of Crane Specifications on FreeCraneSpecs.com
40142 40142 SIDE VIEW DIAGRAM Maximum Vertical Reach Working Area Lifting Capacity Boom Length Crane Weight (Standard) Jib Lengths Winch Bare Drum Pull 201'/61.3 m 360 Degrees 80,000 lbs/36,287 kg 142
More informationWorking Range GROVE MODEL TM TON CAPACITY. LIFTING CHARTS - Hydraulic Truck Cranes 9'-7"
LIFTING CHARTS - Hydraulic Truck Cranes GROVE MODEL - TON CAPACITY Working Range 42-1 ft. (12.8-39.6 m) 33-58 ft. (10.0-17.7 m) 3 FEET 210 200 1 58 48 1 1 33 1 1 1 1 1 115 85 20 10 0 20 10 0 1 1 1 1 1
More informationRT875E. product guide. contents
product guide contents Features 2 Specifications 3 Dimensions 5 Working Range 6 Bifold Load Charts 7 features 75 ton (68 mt) capacity 41 ft-128 ft (12.6 m-39.0 m) 4 section, full power boom 33 ft-56 ft
More informationRT875E. product guide. contents
product guide contents Features 2 Specifications 3 Dimensions 5 Working Range 6 Bifold Load Charts 7 features 75 ton (68 mt) capacity 41 ft-128 ft (12.6 m-39.0 m) 4 section, full power boom 33 ft-56 ft
More informationSeries 400B. product guide. contents. features. 56' Three-section boom. Features Ton rating. Internal anti-two-block. Mounting Configurations 3
Series 4B product guide features 56' Three-section boom 1 Ton rating Internal anti-two-block Self-lubricating Easy Glide wear pads contents Features 2 Mounting Configurations 3 Specifications 4 Capacities:
More informationSeries 400B. product guide. contents. features. 56' Three-Section Boom. Features Ton Rating. Internal Anti-two-block. Mounting Configurations 3
Series 4B product guide features 56' Three-Section Boom 1 Ton Rating Internal Anti-two-block Self-lubricating Easy Glide Wear Pads contents Features 2 Mounting Configurations 3 Specifications 4 Capacities:
More informationRT875E. product guide. contents
product guide contents Features 2 Specifications 3 Dimensions 5 Working Range 6 Bifold Load Charts 7 features 75 ton (68 mt) capacity 41 ft-128 ft (12.6 m-39.0 m) 4 section, full power boom 33 ft-56 ft
More informationTECHNICAL SPECIFICATIONS
45127 45127 SIDE VIEW DIAGRAM Maximum Vertical Reach Working Area Lifting Capacity Boom Length Crane Weight (Standard) Jib Lengths Winch Bare Drum Pull 192'/58,5 m 360 Degrees 90,000 lbs/40 823 kg 127
More information50105R TECHNICAL SPECIFICATIONS 50105R SIDE VIEW DIAGRAM. Powered Boom Sections 4 Overall Height
50105R 50105R SIDE VIEW DIAGRAM Maximum Vertical Reach Working Area Lifting Capacity Boom Length Crane Weight (Standard) Jib Lengths Winch Bare Drum Pull 164'/50 m 360 Degrees 100,000 lbs/45,359 kg 105
More information43' (13.07) 18' 4" (5.59 ) 18' 6" (5.64) Turning Radius: TMS870-45' 1" (13.7 m) TTS870-29' 8" (9.04 m) (8 wheel)
Dimensions 14' 1/2" (4.28) TAILSWING 7' 7" (2.77) O/R RET. 8' 6" (2.59) 15' 5" (5.64) O/R PART. EXTENDED 24' (7.31) ' 6" (4.5) RETRACTED 137' 9" (1653.62) EXTENDED 43' (13.07) 11' 8-1/4" (3.56) 1' 8" (0.53)
More informationSeries 1300A. product guide. contents. features. All New Design. Features ' Four-Section Boom. Mounting Configurations 3.
Series product guide features All New Design 110' Four-Section Boom 30 Ton Rating Self-lubricating Easy Glide Wear Pads Internal Anti-twoblock NEW VISION CAB contents Features 2 Mounting Configurations
More informationSeries 600E. product guide. contents. features. All New Design. Features 2. 90' Four-Section Boom. 20 Ton Rating. Mounting Configurations 3
Series 6E product guide features All New Design 9' Four-Section Boom 2 Ton Rating Self-lubricating Easy Glide Wear Pads Internal Anti-two-block Auxiliary Stabilizers Variable Displacement Hydraulic System
More information400B Product Guide. Features. ASME B30.5 Imperial 85% 9,1 t (10 USt) rating. Multiple mounting configurations. 17,1 m (56 ft) three-section boom
4B Product Guide ASME B3.5 Imperial 85% Features 9,1 t (1 USt) rating 17,1 m (56 ft) three-section boom Multiple mounting configurations Internal anti-two block NATIONAL CRANE 4B The 4B Series delivers
More informationNational Crane Series 800D Product Guide ASME B30.5 Imperial 85%
National Crane Series 8D Product Guide ASME B3.5 Imperial 85% Features 2,87 t (23 USt) rating 3,48 m (1 ft) four-section boom Self-lubricating Easy Glide wear pads Internal Anti-Two Block Features National
More informationCROSSOVER 4500L. 45T capacity class Boom Truck Crane Datasheet imperial. View thousands of Crane Specifications on FreeCraneSpecs.com.
45T capacity class Boom Truck Crane Datasheet imperial Features 45 ton rated capacity @ 9 ft from center of rotation 129 ft maximum boom length 136 ft maximum tip height 32/49 ft optional jib 183 ft maximum
More informationRT700E. product guide. contents
product guide contents Features 2 Specifications 3 Dimensions 5 Working Range 6 features -60 ton (-55 mt) capacity 36 ft-110 ft (11 m-33.5 m) 4 section, full power boom 33 ft (10.1 m) offsettable lattice
More informationSeries 500E. product guide. contents. features. All New Design. Features 2. 71' Three-Section Boom. 18 Ton Rating. Mounting Configurations 3
Series product guide features All New Design 71' Three-Section Boom 18 Ton Rating Self-lubricating Easy Glide Wear Pads Internal Anti-two-block Auxiliary Stabilizers Variable Displacement Hydraulic System
More informationRT600E. product guide. contents
product guide contents Features 2 features 33-5 ft. (-32 m) 4-section full power boom 29-51 ft. (8.8-15.5 m) telescopic swingaway extension Max main boom tip height of 112 ft. (34 m) E Series cab Max overall
More informationCM170 TELESCOPIC CRANE CONTENTS ///////////////////////////////////////////////////////////////////////////////////////// Crane Features...4 Boom Diagram...5 Load Chart: Main Boom & Jib...6 LMI Codes...7
More informationTMS700E. product guide. contents. features 50 or 60 ton (50 or 55 mt) Capacity. Truck Mounted Hydraulic Crane. Features 2
TMS0E product guide features or ton ( or mt) Capacity 36 ft.-1 ft. (11-33.5 m) 4 section, full power sequenced synchronized boom 33 ft.-56 ft. (.1-17 m) offsettable bi-fold lattice swingaway extension
More informationCROSSOVER T capacity class Boom truck crane Datasheet imperial
CROSSOVER 00 T capacity class Boom truck crane Datasheet imperial CROSSOVER 00 Features tons @ 10 capacity at rated distance from center of rotation 110 maximum boom length 118 maximum tip height 32/57
More informationRT700E. product guide. contents
product guide contents Features 2 Specifications 3 Dimensions 5 Working Range 6 features - ton (-55 mt) capacity 36 ft-1 ft (11 m-33.5 m) 4 section, full power boom 33 ft (.1 m) offsettable lattice swingaway
More informationTMS900E. product guide. contents. features 90 ton (80 mton) capacity. Truck Crane ft ( m) 5 section full power boom
features 90 ton (80 mton) capacity 37-142 ft (11.2-43.2 m) 5 section full power boom Patented TWIN-LOCK boom pinning system 33-56 ft (10-17m) bifold lattice swingaway extension Optional 33-56 ft (10-17
More informationCROSSOVER Datasheet imperial. Boom Truck Crane 60T capacity class. Features
Boom Truck Crane T capacity class Datasheet imperial Features tons @ 10 capacity at rated distance from center of rotation 110 maximum boom length 115 maximum tip height 32/57 optional jib 1 maximum sheave
More information32117R TECHNICAL SPECIFICATIONS 32117R SIDE VIEW DIAGRAM. Maximum Vertical Reach. Powered Boom Sections 5 Overall Height
32117R 32117R SIDE VIEW DIAGRAM Maximum Vertical Reach 153'/46,6 m Working Area 180 Degrees Standard (360 Optional) Lifting Capacity 64,000 lbs/29 030 kg Boom Length 117 /35,6 m Crane Weight (Standard)
More informationTRUCK MOUNTED HYDRAULIC CRANE
TRUCK MOUNTED HYDRAULIC CRANE Dimensions STEERING RADIUS 34' 10" (10617mm) C L ROTATION 12' 0" TAILSWING (3657 mm) 8' 4.0" (25 mm) 6' 10.69" (2100 mm) FRONT TRACK 6' 0.3" (1837 mm) REAR TRACK 7' 10" (23
More informationUPTime is the Manitex commitment to complete support of thousands of units working every day.
UPTime is the Manitex commitment to complete support of thousands of units working every day. MANITEX 3000 South Austin Avenue Georgetown, Texas 78626 1-877-314-3390 www.manitex.com MTX CM50 1 PC-EN-V1-1113
More informationTMS900E. product guide. contents. features 90 ton (80 mton) capacity. Truck Crane ft ( m) 5 section full power boom
features 90 ton (80 mton) capacity 37-142 ft (11.2-43.2 m) 5 section full power boom Patented TWIN-LOCK boom pinning system 33-56 ft (10-17m) bifold lattice swingaway extension Optional 33-56 ft (10-17
More informationNational Crane Series 1300A
National Crane Series 1300A Product Guide ASME B30.5 Imperial 85% Features 27,2 t (30 USt) rating 33,52 m (110 ft) four-section boom Self-lubricating Easy Glide wear pads Internal anti-two-block Vision
More informationCourtesy of Crane.Market
CM19 TELESCOPIC CRANE PRELIMINARY CONTENTS / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Crane Features...4 Boom Diagram...5 Load
More informationPRELIMINARY CONTENTS CM190 TELESCOPIC CRANE
CM190 TELESCOPIC CRANE PRELIMINARY CONTENTS /////////////////////////////////////////////////////////// Crane Features...4 Boom Diagram...5 Load Chart: Main Boom & Jib...6 LMI Codes...7 Reeving Diagram...7
More informationseries 2802 product guide features BOOM TRUCKS
series 2802 BOOM TRUCKS features 28 Ton (24,4 mton) Capacity 4-Section 102' (31,0 m) Proportional Boom 4-Section 92' (28.0 m) Proportional Boom 2-Section 26' (7,9 m) to 46' (14,0 m) Telescopic Jib 157'
More informationTADANO MODEL TM TON CAPACITY
LIFTING CHARTS - Trucks TADANO MODEL TM-35100-35 TON CAPACITY WORKING RANGE 25 45 5 160ʼ 150ʼ 140ʼ 79.5 7 6 100ft + 28.2ʼ jib 100ft + 50.0ʼ jib 5 45 4 35 3 86.2ft 100ft 130ʼ 120ʼ 110ʼ 100ʼ 90ʼ 80ʼ 70ʼ
More informationCONTENTS CM300.1 SERIES TELESCOPIC CRANE
CM300.1 SERIES TELESCOPIC CRANE CONTENTS ///////////////////////////////////////////////////////////////////////////////////////// Crane Features... 4 3051T Chassis... 5 30100C Chassis... 6 Outrigger Extension...
More informationGrove TMS9000E. Product Guide. Features
Grove TMS9000E Product Guide Features 90 t (110 USt) capacity 11,2 m - 43,3 m (36 ft - 142 ft) five-section full power boom Patented TWIN-LOCK boom pinning system 10 m - 17 m (33 ft - 56 ft) bi-fold lattice
More informationRT100 ROUGH TERRAIN CRANE DATASHEET - IMPERIAL. Features:
ROUGH TERRAIN CRANE DATASHEET - IMPERIAL Features: Rated capacity: 100 ton @ 10 ft working radius Maximum boom length: 174 ft Maximum tip height: 183 ft Maximum hook height: 174.5 ft CONTENTS Key............................................................................................
More informationTMS9000E Product Guide
TMS9000E Product Guide Features 90 t (110 USt) capacity 11,2 m - 43,4 m (36 ft - 142 ft) five-section full power boom Patented TWIN-LOCK boom pinning system 10 m - 17 m (33 ft - 56 ft) bi-fold lattice
More informationKEY. Hook block. Operator aids. Distance from hook to head sheave pin. Cab. Hook and ball. Heating / Air conditioning. Hydraulics.
KEY /////////////////////////////////////////////////////////////////////////////////////////////////////////////// Operator aids Hook block Cab Distance from hook to head sheave pin Heating / Air conditioning
More informationGrove RT890E. Introduced: Capacity: 90 US (80 Metric) Tons
Grove E Introduced: 2003 Capacity: 90 US (80 Metric) Tons Dimensions OAL: 45 FT. 3 IN. (13.8M) CHASSIS LENGTH: 28 FT. 0 IN. (8.5M) OAW: 10 FT. 11 IN. (3.3M) OAH: 12 FT. 4 IN. (3.7M) Boom Standard 5 section
More informationNational Crane 1800 Series
National Crane 1800 Series Product Guide Features 36,29 t (40 USt) rating 43,28 m (142 ft) five-section boom (80 ft) Self-lubricating Easy Glide wear pads Tailswing counterweight Features Outriggers Outrigger
More informationGrove TMS800E Product Guide
View View thousands thousands of of Crane Crane Specifications Specifications on on FreeCraneSpecs.com FreeCraneSpecs.com Grove TMS800E Product Guide Features 12,6 m - 39 m (41 ft - 128 ft) four-section
More information1560F TECHNICAL SPECIFICATIONS 1560F SIDE VIEW DIAGRAM. Maximum Vertical Reach. Powered Boom Sections 3 Overall Height
1560F 1560F SIDE VIEW DIAGRAM Maximum Vertical Reach 90'/27,4 m Working Area 180 Degrees Standard (360 Optional) Lifting Capacity 30,000 lbs/13 608 kg Boom Length 60 /18,3 m Crane Weight (Dry) 14,825 lbs/6725
More informationPRELIMINARY CROSSOVER T capacity class Boom Truck Crane Datasheet imperial. View thousands of Crane Specifications on FreeCraneSpecs.
80T capacity class Boom Truck Crane Datasheet imperial PRELIMINARY Features 80 ton rated capacity @ 10 ft from center of rotation 126 ft maximum boom length 135 ft maximum tip height 33/57 ft optional
More informationNational Crane 400B Series
National Crane 4B Series Product Guide Features 17,1 m (56 ft) three-section boom 9,1 t (1 USt) rating Self-lubricating Easy Glide wear pads Internal anti-two block Features National Crane Series 4B 9,7
More informationTMS900E. product guide. contents. features 90 ton (80 mton) capacity. Truck Crane ft ( m) 5 section full power boom
features 90 ton (80 mton) capacity 37-142 ft (11.2-43.2 m) 5 section full power boom Patented TWIN-LOCK boom pinning system 33-56 ft (10-17m) bifold lattice swingaway extension Optional 33-56 ft (10-17
More informationdata model 2892S product guide contents features 28 ton (25,4 mton) capacity 4-section, 92' (28,0 m) proportional boom
data features 28 ton (25,4 mton) capacity 4-section, 92' (28,0 m) proportional boom 101' 9"(31,0 m) maximum main boom tip height 147' 9" (45,0 m) maximum tip height with telescoping jib 2-section, 26'
More informationCROSSOVER T capacity class Boom truck crane Datasheet imperial
80T capacity class Boom truck crane Datasheet imperial Features 80 ton rated capacity @ 10 ft from center of rotation 126 ft maximum boom length 135 ft maximum tip height 33/57 ft optional jib 190 ft maximum
More informationCROSSOVER 8000 CROSSOVER T capacity class Boom Truck Crane Datasheet imperial. Features
80T capacity class Boom Truck Crane Datasheet imperial PRE AR N I M LI Y Features 80 ton rated capacity @ 10 ft from center of rotation 126 ft maximum boom length 135 ft maximum tip height 33/57 ft optional
More informationRT530E-2 Product Guide
RT530E-2 Product Guide ASME B30.5 Imperial 85% Features 30 t (30 USt) capacity 8,8 m 29 m (29 ft 95 ft) four-section fullpower boom 7,9 m 13,7 m (26 ft 45 ft) offsettable telescopic swingaway extension
More information30105F TECHNICAL SPECIFICATIONS 30105F SIDE VIEW DIAGRAM. Maximum Vertical Reach. Powered Boom Sections 4 Overall Height
30105F 30105F SIDE VIEW DIAGRAM 6 Maximum Vertical Reach 162'/49 m Working Area 180 Degrees Standard (360 Optional) Lifting Capacity 60,000 lbs/27 216 kg Boom Length 105 /32 m Crane Weight (Standard) 28,160
More informationCourtesy of Crane.Market
1039F 1039F SIDE VIEW DIAGRAM Maximum Vertical Reach 49'/15 m Powered Boom Sections Working Area 180 Degrees Standard (360 Optional) Overall Height Lifting Capacity Operator Controls 20,000 lbs/9,072 kg
More informationLOAD CHARTS TMS9000E 85% STABILITY SERIAL NUMBER
LOAD CHARTS TMS9000E 85% STABILITY SERIAL NUMBER TMS9000E - S/N 1 TMS9000E - S/N 2 CONTENTS GENERAL NOTES...11 WEIGHT REDUCTIONS AND WARNING NOTES... 12 COUNTERWEIGHT CONFIGURATIONS... 13-15 LIFTING AREA
More informationSeries product guide. contents. features. View thousands of Crane Specifications on FreeCraneSpecs.com. 127 ft (38.70 m) Five-Section Boom
Series 15 product guide features 127 ft (38. m) Five-Section Boom 36 USt (32.66 t) Rating Easy Glide Wear Pads contents Features 2 Mounting Configurations 3 Specifications 4 Capacities 5 Accessories 9
More informationRT 345 XL. 45 USt Lifting Capacity Rough Terrain Crane Datasheet Imperial. Features:
USt Lifting Capacity Rough Terrain Crane Datasheet Imperial Features: Rated capacity: USt @ 9 ft working radius Maximum boom length: 5 ft Maximum tip height: 147 ft 1 CONTENTS Page: Key...3 Dimensions
More informationGrove RT540E. Product Guide. Features. 35 t (40 USt) capacity. 9,8 m 31 m (32 ft 102 ft) 4-section full power boom
Grove RT5E Product Guide Features t ( USt) capacity 9,8 m 31 m (32 ft 102 ft) 4-section full power boom 7,9 m 13,7 m (26 ft ft) offsettable telescopic swingaway extension Dual-axis electric joystick controllers
More informationseries 5002 B O O M T R U C K S
series 5002 B O O M T R U C K S features 50 Ton (45,4 Mton) Capacity 4-Section 110 (33,5 M) Proportional 4-Section 96 (29,3 M) Proportional 2-Section 32 (9,8 M) To 49 (14,9 M) Telescopic Offset Jib (15,
More informationCONTENTS TC500 SERIES TELESCOPIC CRANE
TC500 SERIES TELESCOPIC CRANE CONTENTS /////////////////////////////////////////////////////////////////////////////////////////////////////////////// Crane Features...4 5096S Chassis Data - S Models...
More informationGrove YB Product Guide. Features. ASME B30.5 Imperial 85%, Metric 85%, DIN/ISO. 13,6 t (15 USt) capacity
Grove YB5515-2 Product Guide ASME B3.5 Imperial 85%, Metric 85%, DIN/ISO Features 13,6 t (15 USt) capacity 12,5 m (41 ft) three-section, full-power synchronized boom 9,1 t (1 USt) deck carrying capacity
More informationSeries 1400 Hydraulic Crane 33 Ton Load Ratings
Series 1 Hydraulic Crane 33 Ton Load Ratings! DANGER AN UNTRAINED OPERATOR SUBJECTS HIMSELF AND OTHERS TO DEATH OR SERIOUS INJURY YOU MUST NOT OPERATE THIS CRANE UNLESS You have been trained in the safe
More informationRT XL RT XL. 45 USt Lifting Capacity Rough Terrain Crane Datasheet Imperial. Features:
USt Lifting Capacity Rough Terrain Crane Datasheet Imperial Features: Rated capacity: USt @ 9 ft working radius Maximum boom length: 5 ft Maximum tip height: 147 ft 1 CONTENTS Page: Key............................................................................................
More informationdata models 30100C 30124C product guide contents features 30 ton (27,3 mton) capacity 5-section 124' (37,8 m) proportional boom
data features ton (27,3 mton) capacity models 0C 4C 5-section 4' (37, m) proportional boom 4-section 0' (,5 m) proportional boom 134' " (41 m) maximum main boom tip height 2-section, ' " (9,3 m) to 55'
More information