REVOLUTION DRIVES & MOUNTS

Size: px
Start display at page:

Download "REVOLUTION DRIVES & MOUNTS"

Transcription

1 TURNING CHALLENGES INTO SOLUTIONS! REVOLUTION DRIVES & MOUNTS YOU HAVE CHALLENGES. WE HAVE SOLUTIONS! FAX COPYRIGHT PENGO CORPORATION CONTACT

2 Removable Top Section FEATURES Large highly efficient gearboxes, designed specifically for long duty cycles. Standard cross-over pressure relief systems to protect the motor from pressure spikes. Two piece bail housing design allows top section to be removed for easy motor access. Single and Two speed models do not require drain lines. All models are designed to be outfitted with PENGO's TruLink torque monitoring system. All two speed models are equipped with a pressure activated auto shift feature. PROVIDE ACCURATE TORQUE AND SPEED SPECIFICATIONS PENGO ensures that all torque and speed specifications have maximum efficiencies applied to provide the most accurate specifications possible. None of the specifications are listed at 100% theoretical values. Cross-Over Relief Operator's Manual Storage TruLink Ready Transducer Ports Highly Efficient Gearboxes COMPLETE SYSTEM PENGO offers a complete Drive package which includes: Mounting Brackets for: - Skid Loaders - Backhoe Loaders - Excavators (Compact & Large) Anchor drive tool adapters. TruLink digital torque monitoring system. APPLICATIONS ANCHORING: The RS, RT and RV models are designed specifically for the anchor installation industry. The high torque and slow speed configuration is ideal for anchor applications. DRILLING: The DS, DT and DV series are ideal for various types of drilling applications. Torque ranges from 2,500 ft/lb to 40,000 ft/lb. PENGO DRIVES LIMITED WARRANTY NOTE: PENGO Drives are not warranted for DTH applications. The DTH application will cause issues with the shaft and hydraulic motor. All new PENGO products are warranted to be free from defects in material and workmanship, which may cause failure under normal usage and service when used for the purpose intended. PENGO warrants its gearbox for a period of twenty-four (24) months and twelve (12) months on the Hydraulic Motor Dating from the delivery to the original user. The PENGO warranty covers faulty workmanship and defective parts manufactured by PENGO. The warranty does not extend to transportation cost of parts nor does it cover consequential loss, damage to Hydraulic Hoses or ground engaging parts such as Sprockets, Digging Chain, Bearings and Teeth. PENGO Equipment must be operated in accordance with the recommended procedures and within the ranges as specifi ed both on the Unit and contained in the Operating Manual. Any claims under this warranty must be made within fourteen (14) days after the buyer learns of the facts upon which claim is based. All claims not made in writing and not received by PENGO within the time specifi ed above may be deemed waived. Serial Number must accompany all claims. Pengo will not be responsible for or accept any charges for work carried out by any repairs, or for any charges for any spare parts fi tted to any PENGO products without written approval from PENGO. This warranty is void if field repairs have been made to the hydraulic motors, gearboxes, and controls without written approval. The complete unit must be available for inspection in it s original but alleged failed condition. PENGO S liability for any and all losses and damages to buyer resulting from any cause whatsoever, including PENGO negligence irrespective of whether such defects are discoverable or latent, shall in no event exceed the purchase price of the particular parts, with respect to which losses or damages are claimed, or, at the discretion of PENGO the repair or replacement of defective or damaged parts. Any goods returned to PENGO by the customer under Warranty or repair must have all freight charges prepaid for on the customer s Account.

3 DRIVE MOUNTS Examples SKID LOADER MOUNTING SYSTEM (Long Reach) Provides maximum ground clearance of 7' to 11' depending model selected. Increases height capability so drillers can use longer auger bits and anchor installers can use longer sections. Unique design optimizes the operators visibility by positioning the Drive up to 48" from the front of the skid loader. Standard retractable stabilizer arms allow the Drive attachment to stand upright when not in use. Improves ability to store, transport and attach to the skid loader. Designed to be used with up to a 12,000 ft/lb Drive. Excavator quick coupler mount used with DT-15 Drive and auger. Long reach skid mount used to install helical anchors. MOUNTING SYSTEM Complete mounting system for all sizes of excavators. Mounts can mount directly to the boom or be designed to work with an existing quick coupler. Excavator mounts allow for maximum movement to ensure the Drive always hangs true to the ground. Custom mounts can be designed for specific applications. Mounts are available for the entire range of Drives offered by PENGO. 1. Pengo reserves the right to determine whether products claimed to be defective shall be inspected by our personnel in the field or returned to the factory. If judged by Pengo to be defective in material or workmanship, the product will be replaced or a credit issued at the option of Pengo. 2. Upon notification of defect, Pengo s Inside Sales Department will issue a Return Goods Authorization number (RGA). All returns for replacement or credit MUST be accompanied by a RGA number. Products returned without a RGA number will be rejected and returned to the sender freight collect. RETURNS and CLAIMS 3. All returns must be shipped prepaid. Products shipped collect will be refused. Proof of purchase such as invoice number must accompany returns. 4. Slow moving dealer inventory may be returned once per calendar year. The net value cannot exceed 5% of the previous year s purchases. A 20% re-stocking charge will apply to the net value or returned products. All returns must be of current manufacture and in new condition. Rusty or custom painted products will not be accepted for return. CONTACT PENGO SALES AT:

4 PENGO's Revolution Series Drives are designed to outfit several different types of equipment. This selection guide will assist you in selection the right model for your equipment type. power pack compact skid-steer mini excavator DRILLING DRIVE D SERIES Designed for Drilling Applications Part No. Model Connection Speed Config. Max Flow (gpm) Max Torque Low (ft/lbs) Torque High (ft/lbs) Speed Excavator Size (metric tons) DS-2 H-200 Sngl T - 3T DS-2 R-256 Sngl T - 3T DS-3 H-200 Sngl T - 4T DT-5 H-250 Two / 100 3T - 6T DT-15 H-300 Two / 40 12T - 20T DV-20 H-300 Var / 40 12T - 20T DV-30 S-400 Var / 41 15T - 25T DV mm Var / 34 15T - 25T Power Pack Recommended Prime Mover Cmpt Digger Derrick Compt Excavator Skid Steer Loader Digger Derrick Backhoe (TLB) Excavator skid-steer mini digger derrick digger derrick backhoe excavator ANCHOR DRIVE R SERIES Designed for Anchor Installation Applications Part No. Model Connection Speed Config. Max Flow (gpm) Max Torque Low (ft/lbs) CONNECTIONS: H-200 = 2" Hex, R-256 = 2 9/16" Round, H-250 = 2 1/2" Hex, H-300 = 3" Hex, and S-400 = 4" Square, MM Hubs are Square Note: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage Torque High (ft/lbs) Speed Excavator Size (metric tons) RS-6X H-200 Sngl NA RS-6 H-200 Sngl T - 6T RS-7X H-200 Sngl NA RS-7 H-200 Sngl T - 6T RS-12 H-250 Sngl T - 12T RT-9 H-250 Two / 63 4T - 8T RT-12 H-250 Two / 54 6T - 12T RT-20 H-300 Two / 25 12T - 20T RT-30 S-400 Two / 19 15T - 25T RT mm Two / 15 15T - 25T RV mm Var /17 30T - 40T RV mm Var /10 35T - 45T RV mm Var /8 45T-60T RV mm Var /6 60T-90T Power Pack Recommended Prime Mover Cmpt Digger Derrick Compt Excavator Skid Steer Loader Digger Derrick Backhoe (TLB) Excavator PENGOATTACHMENTS.COM

5 DRILLING DRIVES From small to large, the Revolution Series drilling drives are equipped to get the job done. These high speed drive units are recommended to be used on mini skid steers, skid steers, mini excavators, backhoes, and excavators with Pengo augers. Pengo can supply you the drive and mount specific to your carrier. Contact our sales team to determine which drive is the best fit for your operation PENGOATTACHMENTS.COM

6 MS-100 PAGE 6 This single speed Revolution Drive for mini skid steer is your solution to backyard dirt digging. It's compact size accommodates the Landscape Aggressor auger perfectly. Universal Compact Skid Mount and Hydraulic Hoses included. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: 4' (48") DEPTH: 4' (48") SINGLE SWIVEL MS-100 Part No R-256 Connection 146 lbs. (66 Kg) MS-100 Part No H-200 Connection 146 lbs. (66 Kg) DOUBLE SWIVEL MS-100 Part No R-256 Connection 146 lbs. (66 Kg) MS-100 Part No H-200 Connection 146 lbs. (66 Kg) DRILLING DRIVES Double-Swivel Bracket Double Swivel Bracket Standard-Single 14.6 lbs. Swivel Bracket Convert single-swivel units into double-swivel units 7/8" Pin Assembly lbs. Displacement 6.1 cu/in (100cc) Single Speed Bi-Directional Motor 7/8" Spline 14T SAE - A 2 Bolt 1/2" BSP Cross Over Relief Not Equipped Planetary Single Stage Reduction Ratio 5.77:1 2" Hex or 2-9/16" Round Internal Oil Capacity.13 Gallons REFERENCE TORQUE CHART Speed 10 (38) (56) (75) (94) 134

7 PAGE 7 MS-125 This single speed Revolution Drive for mini skid steer is your solution to backyard dirt digging. It's compact size accommodates the Landscape Aggressor auger perfectly. Universal Compact Skid Mount and Hydraulic Hoses included. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: 4' (48") DEPTH: 4' (48") SINGLE SWIVEL MS-125 Part No R-256 Connection 146 lbs. (66 Kg) MS-125 Part No H-200 Connection 146 lbs. (66 Kg) DOUBLE SWIVEL MS-125 Part No R-256 Connection 146 lbs. (66 Kg) MS-125 Part No H-200 Connection 146 lbs. (66 Kg) Displacement 6.1 cu/in (100cc) Single Speed Bi-Directional Motor 7/8" Spline 14T SAE - A 2 Bolt 1/2" BSP Cross Over Relief Not Equipped Planetary Single Stage Reduction Ratio 5.77:1 2" Hex or 2-9/16" Round Internal Oil Capacity.13 Gallons REFERENCE TORQUE CHART Speed 10 (38) (56) (75) (94) 112 Double Swivel Bracket lbs. 7/8" Pin Assembly lbs. Standard-Single Swivel Bracket Double-Swivel Bracket Convert single-swivel units into double-swivel units DRILLING DRIVES

8 DS-2 PAGE 8 Powerful in dirt, clay and light rock drilling conditions, outfit your skid steer or mini excavator with this single speed drilling drive. The smallest of the Revolution Series, this drive is a perfect companion to the Long Reach Mount with an Aggressor, TriMax or Severe Rock Ripper auger. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: 2T-3T SIZE: 4' (48") DEPTH: 5' (60") 2" HEX CONNECTION Part No T-3T Excavator 115 lbs. (52 Kg) 2 9/16" ROUND CONNECTION Part No T-3T Excavator 115 lbs. (52 Kg) DRILLING DRIVES 45mm Link Arm lbs. Pin for 2" Hex Output shaft mm Pin Assembly lbs. TruLink Class 1 with 4" Monitor Part No with 8" Monitor Part No " Hex lbs. Pin for 2 9/16" Round shaft Displacement cu/in (195cc) Single Speed Bi-Directional Motor 7/8" Spline 14T SAE - A 2 Bolt 1/2" BSP Cross Over Relief Not Equipped Planetary Single Stage Reduction Ratio 5.77:1 2" Hex or 2-9/16" Round Internal Oil Capacity.13 Gallons Shaft Pull Out (lbs.) 3,000 lbs. REFERENCE TORQUE CHART REFERENCE TORQUE CHART Speed 10 (38) (56) (75) (94) Note: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage

9 PAGE 9 DS-3 Powerful in dirt, clay and light rock drilling conditions, outfit your skid steer or mini excavator with this single speed drilling drive. With a little more power than the DS-2, this drive is also a perfect companion to the Long Reach Mount with an Aggressor, TriMax or Severe Rock Ripper auger. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: 2T-4T SIZE: 4' (48") DEPTH: 8' (96") 2" HEX CONNECTION Part No T-4T Excavator 115 lbs. (52 Kg) Displacement 8.0 cu/in (131cc) Single Speed Bi-Directional Motor 1" 6-B Spline SAE - A 2 Bolt 7/8" - 14 O-Ring Cross Over Relief Not Equipped Planetary Two Stage Reduction Ratio 14.79:1 2" Hex Internal Oil Capacity.50 Gallons Shaft Pull Out (lbs.) 7,000 lbs. REFERENCE TORQUE CHART Note: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage REFERENCE TORQUE CHART Speed 10 (38) (56) (75) (94) mm Link Arm lbs. 45mm Pin Assembly lbs. Pin for 2" Hex Output shaft TruLink Class 1 with 4" Monitor Part No with 8" Monitor Part No " Hex lbs. DRILLING DRIVES

10 DT-5 PAGE 10 The DT-5 will mount to the universal skid steer mounts, both standard and long reach, and will turn the TriMax auger or Severe Rock Ripper in those hard rock conditions. The auto shift feature allows the drive to automatically shift between high speed and low torque and low speed high torque depending on the input flow. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. 2 1/2" HEX CONNECTION Part No T-6T Excavator 645 lbs. (292 Kg) SIZE: 3T-6T SIZE: 5' (60") DEPTH: 8' (96") The standard cross-over pressure relief system is designed to protect the motor from pressure spikes and potential overload conditions. Two-Speed Models Must Have Minimum of 20 GPM DRILLING DRIVES 45mm Link Arm lbs. 45mm Pin Assembly lbs. TruLink Class 1 with 4" Monitor Part No with 8" Monitor Part No /2" Hex lbs. Displacement 2.98 cu/in (97.6cc) Low High Two Speed Bi-Directional Motor 1 1/4" Spline 14T 20 (75) SAE - C 4 Bolt 25 (95) /8" - 12 UN-2B 30 (113) Cross Over Relief Set at 3,100 psi 35 (132) (151) Planetary Two Stage Note: Revolution Drive units are not Reduction Ratio 25.36:1 recommended for DTH and will not be 2 1/2" Hex covered under warranty for damage Internal Oil Capacity 2.0 Gallons Shaft Pull Out (lbs.) 22,500 lbs. BELOW CHART FOR LOW TORQUE/HIGH SPEED OUTPUT BELOW CHART FOR HIGH TORQUE/LOW SPEED OUTPUT REFERENCE TORQUE CHART (LT / HS) REFERENCE TORQUE CHART (HT / LS)

11 PAGE 11 DT-15 The DT-15 Drilling drive will turn those utility and small foundation augers in most soil types. The auto shift feature allows the drive to automatically shift between high speed and low torque and low speed high torque depending on the input flow. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: 12T-20T SIZE: 5' (60") DEPTH: 12' (144") 3" HEX CONNECTION Part No T-20T Excavator 825 lbs. (374 Kg) The standard cross-over pressure relief system is designed to protect the motor from pressure spikes and potential overload conditions. Two-Speed Models Must Have Minimum of 20 GPM Displacement 17.8 cu/in (293cc) Low High Two Speed Bi-Directional Motor 1 1/4" Spline 14T 20 (75) 8 16 SAE - C 4 Bolt 30 (113) /8" - 12 UN-2B 40 (151) Cross Over Relief Set at 3,100 psi 50 (190) Note: Revolution Drive units are not Planetary Two Stage recommended for DTH and will not be Reduction Ratio 26.52:1 covered under warranty for damage 3" Hex Internal Oil Capacity 3.0 Gallons Shaft Pull Out (lbs.) 22,500 lbs. BELOW CHART FOR LOW TORQUE/HIGH SPEED OUTPUT BELOW CHART FOR HIGH TORQUE/LOW SPEED OUTPUT REFERENCE TORQUE CHART (LT / HS) REFERENCE TORQUE CHART (HT / LS) mm Link Arm lbs. 45mm Pin Assembly lbs. TruLink Class 1 with 4" Monitor Part No with 8" Monitor Part No " Hex lbs. DRILLING DRIVES

12 DV-20 PAGE 12 The DV-20 is an excellent companion to the Pengo Excavator Auger line. This powerhouse is capable of drilling holes up to 20' deep and 6' in diameter in both rock and dirt. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: 12T-20T SIZE: 6' (72") DEPTH: 20' (240") 3" HEX CONNECTION Part No T-20T Excavator 880 lbs. (400 Kg) Drive will start in high speed and will build torque as drilling resistance increases. Variable-Speed Models Must Have a Drain Line. DRILLING DRIVES 45mm Link Arm lbs. 45mm Pin Assembly lbs. TruLink Class 1 with 4" Monitor Part No with 8" Monitor Part No " Hex lbs. Displacement 8.25 cu/in (135cc) Low High Variable Speed Bi-Directional Motor 8/16 Spline 13T 40 (151) SAE - D 2 Bolt 45 (169) Radial (Quick Coupler) 50 (188) Cross Over Relief None 55 (206) (225) Planetary Three Stage Note: Revolution Drive units are not Reduction Ratio 60.56:1 recommended for DTH and will not be 3" Hex covered under warranty for damage Internal Oil Capacity 3.0 Gallons Shaft Pull Out (lbs.) 45,000 lbs. BELOW CHART FOR LOW TORQUE/HIGH SPEED OUTPUT BELOW CHART FOR HIGH TORQUE/LOW SPEED OUTPUT REFERENCE TORQUE CHART (LT / HS) REFERENCE TORQUE CHART (HT / LS)

13 PAGE 13 DV-30 The High Speed DV-30 Drive is compatible with Pengo's Excavator Auger system. The drive will drill holes up to 20' deep and 6' in diameter in rock, dirt and frozen ground. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: 15T-25T SIZE: 6' (72") DEPTH: 20' (240") 4" SQUARE CONNECTION Part No T-25T Excavator 1250 lbs. (566 Kg) Drive will start in high speed and will build torque as drilling resistance increases. Variable-Speed Models Must Have a Drain Line. Displacement cu/in (165cc) Low High Variable Speed Bi-Directional Motor 8/16 Spline 13T 40 (151) SAE - D 2 Bolt 45 (169) Radial (Quick Coupler) 50 (188) Cross Over Relief None 55 (206) (225) Planetary Three Stage Reduction Ratio 69.70:1 Note: Revolution Drive units are not recommended for DTH and will not be 4" Square covered under warranty for damage Internal Oil Capacity 3.1 Gallons Shaft Pull Out (lbs.) 60,000 lbs. BELOW CHART FOR LOW TORQUE/HIGH SPEED OUTPUT BELOW CHART FOR HIGH TORQUE/LOW SPEED OUTPUT REFERENCE TORQUE CHART (LT / HS) REFERENCE TORQUE CHART (HT / LS) mm Link Arm lbs. 75mm Pin lbs. TruLink Class 2 with 4" Monitor Part No with 8" Monitor Part No " Square lbs. DRILLING DRIVES

14 DV-40 PAGE 14 The DV-40 is the largest drilling drive in the Revolution Series. This drive with turn Pengo Excavator augers 25' deep and as wide as 7' in diameter. Like the DV-30 it is able to drill in most rock, dirt and frozen ground drilling conditions. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: 15T-25T SIZE: 7' (84") DEPTH: 25' (300") 130MM SQUARE CONNECTION Part No T-25T Excavator 1500 lbs. (680 Kg) Drive will start in high speed and will build torque as drilling resistance increases. Variable-Speed Models Must Have a Drain Line. DRILLING DRIVES 75mm Link Arm lbs. 75mm Pin lbs. TruLink Class 2 with 4" Monitor Part No with 8" Monitor Part No MM Square lbs. Displacement cu/in (165cc) Low High Variable Speed Bi-Directional Motor 8/16 Spline 13T 40 (151) 9 23 SAE - D 2 Bolt 45 (169) Radial (Quick Coupler) 50 (188) Cross Over Relief None 55 (206) (225) Planetary Three Stage Note: Revolution Drive units are not Reduction Ratio 83.78:1 recommended for DTH and will not be 130mm Hex covered under warranty for damage Internal Oil Capacity 4.0 Gallons Shaft Pull Out (lbs.) 60,000 lbs. BELOW CHART FOR LOW TORQUE/HIGH SPEED OUTPUT BELOW CHART FOR HIGH TORQUE/LOW SPEED OUTPUT REFERENCE TORQUE CHART (LT / HS) REFERENCE TORQUE CHART (HT / LS)

15 ANCHOR DRIVES Pengo's Revolution Series Anchor drives have been proven to get the job done. With single, double and variable speed models available for power-packs up to 90T excavators, Pengo offers a drive for any type of anchor installation. The addition of our TruLink Torque Monitor, which offers true torque readings that deliver a high degree of accuracy. New to our catalog you will notice that we are now listing our drives with both theoretical and actual torque readings. We still recommend when choosing your drive to go by the actual torque listings. When looking for that competitive edge, choose Pengo Revolution Series Drives PENGOATTACHMENTS.COM

16 RS-6X PAGE 16 The newest addition to Revolution Series Drive is the RS-6X and RS-6 Anchor Drives. The light weight RS-6X offers the shortest overall length and smallest diameter and will be perfect for any hand-held operation to install anchors in those hard to reach places. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: NA Not recommended for Drilling. 2" HEX CONNECTION Part No Hand Held Unit 95 lbs. (39 Kg) ANCHOR DRIVES THE DRIVE YOU NEED TO GET THE JOB DONE! 2" Hex lbs. RS-6 Bail Assembly lbs. RS-6X Anchor Drive For Hand-Held Anchor Installation Shortest Overall Length & Smallest Unit Diameter Fastest RPM Higher GPM Capacity Cross-Over Relief is Standard Highest Torque Output Lightweight - Only 95 lbs. Pin for 2" Hex Output shaft Displacement 18.7 cu/in (306cc) Single Speed Bi-Directional Motor 1" 6B Spline SAE - A 2 Bolt 3/4" -16 O-Ring Cross Over Relief Set at 2700 PSI Planetary Two Stage Reduction Ratio 13.29:1 2" Hex Internal Oil Capacity.50 Gallons Shaft Pull Out (lbs.) 3,000 lbs. REFERENCE TORQUE CHART Note: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage Shown Above: RS-6X Mounting Pattern Speed 10 (38) 9 15 (56) (75) (94) 23

17 PAGE 17 RS-6 The RS-6 Anchor Drive is similar to the RX-6 but includes the bail housing. The RS-6 drives will attach to your skid steer or mini-excavator and it offers the shortest overall length and smallest diameter for drilling. The RS-6 will allow your prime mover access to the tight spaces. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: 3T-6T Not recommended for Drilling. 2" HEX CONNECTION Part No T-6T Excavator 165 lbs. (47 Kg) THE DRIVE YOU NEED TO GET THE JOB DONE! Displacement 18.7 cu/in (306cc) Single Speed Bi-Directional Motor 1" 6B Spline SAE - A 2 Bolt 3/4" -16 O-Ring Cross Over Relief Set at 2700 PSI Planetary Two Stage Reduction Ratio 13.29:1 2" Hex Internal Oil Capacity.50 Gallons Shaft Pull Out (lbs.) 3,000 lbs. REFERENCE TORQUE CHART Speed 10 (38) 9 15 (56) (75) (94) 23 Note: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage RS-6 Anchor Drive For Hand-Held Anchor Installation Shortest Overall Length & Smallest Unit Diameter Fastest RPM Higher GPM Capacity Cross-Over Relief is Standard Highest Torque Output Tru Link Compatible 45mm Link Arm lbs. 45mm Pin Assembly lbs. Pin for 2" Hex Output shaft TruLink Class 1 with 4" Monitor Part No with 8" Monitor Part No " Hex lbs. ANCHOR DRIVES

18 RS-7X PAGE 18 Designed to fit with stand-alone power packs, the RS-7X provides the versatility to be mounted to a skid steer when the bail assembly (sold separately) is attached. This anchor drive allows you to work in small hard to reach places. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: NA Not Recommended for Drilling. 2" HEX CONNECTION Part No lbs. (54 Kg) ANCHOR DRIVES Bail Assembly Kit " Hex lbs. Converts RS-7X Planetary Drive to RS-7 Planetary Drive With bail kit and mount the RS-7X drive can be used with skid steer, also will work with mini excavator and mini digger derricks Pin for 2" Hex Output shaft Displacement 18.7 cu/in (306cc) Single Speed Bi-Directional Motor 1" 6B Spline SAE - A 2 Bolt 3/4" - 16 O-Ring Cross Over Relief Set at 2700 psi Planetary Two Stage Reduction Ratio 14.79:1 2" Hex Internal Oil Capacity.50 Gallons Shaft Pull Out (lbs.) 7,000 lbs. REFERENCE TORQUE CHART Speed 10 (38) 7 15 (56) (75) (94) 17 Note: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage

19 PAGE 19 RS-7 Choose the single speed RS-7 anchor drive for your next installation project. The standard cross-over pressure relief system will protect the hydraulic motor from pressure spikes and potential overload conditions. Add a mount and the TruLink for the complete drive system Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: 3T-6T Not Recommended for Drilling. 2" HEX CONNECTION Part No T-6T Excavator 170 lbs. (77 Kg) Displacement 18.7 cu/in (306cc) Single Speed Bi-Directional Motor 1" 6B Spline SAE - A 2 Bolt 3/4" - 16 O-Ring Cross Over Relief Set at 2700 psi Planetary Two Stage Reduction Ratio 14.79:1 2" Hex Internal Oil Capacity.50 Gallons Shaft Pull Out (lbs.) 7,000 lbs. REFERENCE TORQUE CHART Speed 10 (38) 7 15 (56) (75) (94) 17 Note: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage 45mm Link Arm lbs. 45mm Pin Assembly lbs. Pin for 2" Hex Output shaft TruLink Class 1 with 4" Monitor Part No with 8" Monitor Part No " Hex lbs. ANCHOR DRIVES

20 RS-12 PAGE 20 The single speed RS-12 is good for Mini-Excavators due to the low GPM requirements. With a standard crossover pressure relief system and TruLink compatibility, this drive will not disappoint on your next project. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: 6T-12T Not Recommended for Drilling. 2 1/2" HEX CONNECTION Part No T-12T Excavator 546 lbs. (248 Kg) ANCHOR DRIVES 45mm Link Arm lbs. 45mm Pin Assembly lbs. TruLink Class 1 with 4" Monitor Part No with 8" Monitor Part No /2" Hex lbs. Displacement 23.9 cu/in (390cc) Single Speed Bi-Directional Motor 1 1/2" Spline 17T SAE - C 4 Bolt 1 1/16" - 12 O-Ring Cross Over Relief Set at 3100 psi Planetary Two Stage Reduction Ratio 17.39:1 2 1/2" Hex Internal Oil Capacity 2.0 Gallons Shaft Pull Out (lbs.) 22,500 lbs. REFERENCE TORQUE CHART Note: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage REFERENCE TORQUE CHART Speed 15 (56) 7 20 (75) 9 25 (94) (113) (132) (141)

21 PAGE 21 RT-9 The RT-9 Anchor drive is perfect for the small anchor installation and drilling projects. The auto shift feature allows the drive to automatically shift between high speed and low torque and low speed high torque depending on the input flow. If drilling select the Pengo TriMax or MD auger. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: 4T-8T SIZE: 5' (60") DEPTH: 8' (96") 2 1/2" HEX CONNECTION Part No T-8T Excavator 540 lbs. (245 Kg) Displacement 11.9 cu/in (195cc) Two Speed Bi-Directional Motor 1 1/4" Spline 14T SAE - C 4 Bolt 1 5/8" - 12-UN-2B Cross Over Relief Set at 3100 psi Planetary Two Stage Reduction Ratio 25.36:1 2 1/2" Hex Internal Oil Capacity 2.0 Gallons Shaft Pull Out (lbs.) 22,500 lbs. BELOW CHART FOR LOW TORQUE/HIGH SPEED OUTPUT REFERENCE TORQUE CHART (LT / HS) The standard cross-over pressure relief system is designed to protect the motor from pressure spikes and potential overload conditions. Low 45mm Link Arm lbs. 45mm Pin Assembly lbs. TruLink Class 1 with 4" Monitor Part No with 8" Monitor Part No /2" Hex lbs. High 20 (75) (113) (151) (190) Note: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage BELOW CHART FOR HIGH TORQUE/LOW SPEED OUTPUT REFERENCE TORQUE CHART (HT / LS) Two-Speed Models Must Have Minimum of 20 GPM ANCHOR DRIVES

22 RT-12 PAGE 22 The RT-12 Anchor drive is perfect anchor installation projects when using a skid steer, mini-ex or backhoe. This drive may also be used for some drilling applications with the Pengo MD or Excavator auger system. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: 6T-12T SIZE: 5' (60") DEPTH: 10' (120") 2 1/2" HEX CONNECTION Part No T-12T Excavator 655 lbs. (297 Kg) ANCHOR DRIVES 45mm Link Arm lbs. 45mm Pin Assembly lbs. TruLink Class 1 with 4" Monitor Part No with 8" Monitor Part No /2" Hex lbs. Displacement 14.9 cu/in (244cc) Two Speed Bi-Directional Motor 1 1/4" Spline 14T SAE - C 4 Bolt 1 5/8" - 12 UN-2B Cross Over Relief Set at 3100 psi Planetary Two Stage Reduction Ratio 25.36:1 2 1/2" Hex Internal Oil Capacity 2.0 Gallons Shaft Pull Out (lbs.) 22,500 lbs. BELOW CHART FOR LOW TORQUE/HIGH SPEED OUTPUT REFERENCE TORQUE CHART (LT / HS) The standard cross-over pressure relief system is designed to protect the motor from pressure spikes and potential overload conditions. Low High 20 (75) (113) (151) (190) Note: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage BELOW CHART FOR HIGH TORQUE/LOW SPEED OUTPUT REFERENCE TORQUE CHART (HT / LS) Two-Speed Models Must Have Minimum of 20 GPM

23 PAGE 23 RT-20 When the job calls for larger anchor installation using a backhoe or excavator turn to the RT. The auto shift feature allows the drive to automatically shift between high speed and low torque and low speed high torque depending on the input flow. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: 12T-20T Not Recommended for Drilling. 3" HEX CONNECTION Part No T-20T Excavator 855 lbs. (387 Kg) Displacement 11.9 cu/in (195cc) Two Speed Bi-Directional Motor 1 1/4" Spline 14T SAE - C 4 Bolt 1 5/8" - 12-UN-2B Cross Over Relief Set at 3100 psi Planetary Three Stage Reduction Ratio 60.56:1 3" Hex Internal Oil Capacity 3.0 Gallons Shaft Pull Out (lbs.) 45,000 lbs. BELOW CHART FOR LOW TORQUE/HIGH SPEED OUTPUT REFERENCE TORQUE CHART (LT / HS) The standard cross-over pressure relief system is designed to protect the motor from pressure spikes and potential overload conditions. Low 45mm Link Arm lbs. 45mm Pin Assembly lbs. TruLink Class 1 with 4" Monitor Part No with 8" Monitor Part No " Hex lbs. High 20 (75) (113) (151) (190) Note: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage BELOW CHART FOR HIGH TORQUE/LOW SPEED OUTPUT REFERENCE TORQUE CHART (HT / LS) Two-Speed Models Must Have Minimum of 20 GPM ANCHOR DRIVES

24 RT-30 PAGE 24 Use The RT-30 Anchor drive for larger projects with an excavator. The auto shift feature allows the drive to automatically shift between high speed and low torque and low speed high torque depending on the input flow. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: 15T-25T Not Recommended for Drilling. 4" SQUARE CONNECTION Part No T-25T Excavator 1220 lbs. (553 Kg) ANCHOR DRIVES 75mm Link Arm lbs. 75mm Pin lbs. TruLink Class 2 with 4" Monitor Part No with 8" Monitor Part No " Square lbs. Displacement 13.9 cu/in (227cc) Two Speed Bi-Directional Motor 1 1/4" Spline 14T SAE - C 4 Bolt 1 5/8" - 12 UN-2B Cross Over Relief Set at 3100 psi Planetary Three Stage Reduction Ratio 69.7:1 4" Square Internal Oil Capacity 3.1 Gallons Shaft Pull Out (lbs.) 66,000 lbs. BELOW CHART FOR LOW TORQUE/HIGH SPEED OUTPUT REFERENCE TORQUE CHART (LT / HS) The standard cross-over pressure relief system is designed to protect the motor from pressure spikes and potential overload conditions. Low High 20 (75) (113) (151) (190) 9 19 Note: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage BELOW CHART FOR HIGH TORQUE/LOW SPEED OUTPUT REFERENCE TORQUE CHART (HT / LS) Two-Speed Models Must Have Minimum of 20 GPM

25 PAGE 25 RT-40 The RT-40 Anchor drive is perfect for the larger anchor installation projects when using an excavator. The auto shift feature allows the drive to automatically shift between high speed and low torque and low speed high torque depending on the input flow. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE: 15T-25T Not Recommended for Drilling. 130MM SQUARE CONNECTION Part No T-25T Excavator 1440 lbs. (653 Kg) Displacement 15.8 cu/in (260cc) Two Speed Bi-Directional Motor 1 1/4" Spline 14T SAE - C 4 Bolt 1 5/8" - 12-UN-2B Cross Over Relief Set at 3100 psi Planetary Three Stage Reduction Ratio 83.78:1 130MM Square Internal Oil Capacity 4.0 Gallons Shaft Pull Out (lbs.) 60,000 lbs. BELOW CHART FOR LOW TORQUE/HIGH SPEED OUTPUT REFERENCE TORQUE CHART (LT / HS) The standard cross-over pressure relief system is designed to protect the motor from pressure spikes and potential overload conditions. Two-Speed Models Must Have Minimum of 20 GPM Low 75mm Link Arm lbs. 75mm Pin lbs. TruLink Class 2 with 4" Monitor Part No with 8" Monitor Part No MM Square lbs. High 20 (75) (113) (151) (190) 7 15 Note: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage BELOW CHART FOR HIGH TORQUE/LOW SPEED OUTPUT REFERENCE TORQUE CHART (HT / LS) ANCHOR DRIVES

26 RV-100 PAGE 26 The RV-100 Series Variable Speed Drive is strictly for anchor installation due to it's ability to generate a high-level of sustained and consistent torque. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE (Tons) 30T-40T 150MM SQUARE CONNECTION Part No T-40T Excavator 2850 lbs. (1292 Kg) Motor will shift once it reached 2900 psi. Need a minimum of 3100 psi to achieve max motor displacement. Variable-Speed Models Must Have a Drain Line. ANCHOR DRIVES THE DRIVE YOU NEED TO GET THE JOB DONE! 150MM Square lbs. TruLink Class 3 with 8" Monitor Part No Displacement cu/in (225cc) Variable Speed Bi-Directional Motor 13T 8/16 DP Spline SAE - D 4 Bolt Code 62 SAE Split Flange Cross Over Relief Not Equipped Planetary Three Stage Reduction Ratio 126:1 150MM Square Internal Oil Capacity 12.0 Gallons Shaft Pull Out (lbs.) 100,000 lbs. BELOW CHART FOR LOW TORQUE/HIGH SPEED OUTPUT REFERENCE TORQUE CHART (LT / HS) Low Torque (119cc) Up To 2900 psi Note: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage BELOW CHART FOR HIGH TORQUE/LOW SPEED OUTPUT REFERENCE TORQUE CHART (HT / LS) Low 147cc High Torque (225cc) Up To 3100 psi High 225cc 80 (302) (370) (378) (416) (454) 21 14

27 PAGE 27 RV-150 The RV-150 Series Variable Speed Drive is strictly for anchor installation due to it's ability to generate a high-level of sustained and consistent torque. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE (Tons) 35T-45T 177MM SQUARE CONNECTION Part No T-45T Excavator 3800 lbs. (1724 Kg) Motor will shift once it reached 2900 psi. Need a minimum of 3100 psi to achieve max motor displacement. Variable-Speed Models Must Have a Drain Line. Displacement cu/in (225cc) Variable Speed Bi-Directional Motor 13T 8/16 DP Spline SAE - D 4 Bolt Code 62 SAE Split Flange Cross Over Relief Not Equipped Planetary Four Stage Reduction Ratio :1 177MM Square Internal Oil Capacity 12 Gallons Shaft Pull Out (lbs.) 180,000 lbs. BELOW CHART FOR LOW TORQUE/HIGH SPEED OUTPUT REFERENCE TORQUE CHART (LT / HS) Low Torque (119cc) Up To 2900 psi Note: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage BELOW CHART FOR HIGH TORQUE/LOW SPEED OUTPUT REFERENCE TORQUE CHART (HT / LS) High Torque (225cc) Up To 3100 psi THE DRIVE YOU NEED TO GET THE JOB DONE! 177MM Square lbs. TruLink Class 3 with 8" Monitor Part No Low 147cc High 225cc 80 (302) (370) (378) (416) (454) 13 9 ANCHOR DRIVES

28 RV-200 PAGE 28 The RV-200 Series Variable Speed Drive is strictly for anchor installation due to it's ability to generate a high-level of sustained and consistent torque. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. SIZE (Tons) 45T-60T 177MM SQUARE CONNECTION Part No T-60T Excavator 4200 lbs. (1814 Kg) Motor will shift once it reached 2900 psi. Need a minimum of 3100 psi to achieve max motor displacement. Variable-Speed Models Must Have a Drain Line. ANCHOR DRIVES THE DRIVE YOU NEED TO GET THE JOB DONE! 177MM Square lbs. TruLink Class 4 with 8" Monitor Part No Displacement cu/in (225cc) Variable Speed Bi-Directional Motor 13T 8/16 DP Spline SAE - D 4 Bolt Code 62 SAE Split Flange Cross Over Relief Not Equipped Planetary Four Stage Reduction Ratio :1 177MM Square Internal Oil Capacity 14 Gallons Shaft Pull Out (lbs.) 250,000 lbs. BELOW CHART FOR LOW TORQUE/HIGH SPEED OUTPUT REFERENCE TORQUE CHART (LT / HS) Low Torque (119cc) Up To 2900 psi Note: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage BELOW CHART FOR HIGH TORQUE/LOW SPEED OUTPUT REFERENCE TORQUE CHART (HT / LS) Low 147cc High Torque (225cc) Up To 3100 psi High 225cc 80 (302) (370) (378) (416) (454) 10 7

29 PAGE 29 RV-300 The RV-300 is the largest of anchor drives. It has the ability to power through the largest of anchor installation projects. Due to it's ability to generate a high-level of sustained and consistent torque it is not recommended for drilling. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. Note that both theoretical and actual torque values are listed, but that PENGO recommends to go by torque listings. 200MM SQUARE CONNECTION Part No T-90T Excavator 5000 lbs. (2267 Kg) SIZE (Tons) 60T-90T Motor will shift once it reached 2900 psi. Need a minimum of 3100 psi to achieve max motor displacement. Variable-Speed Models Must Have a Drain Line. Displacement cu/in (225cc) Variable Speed Bi-Directional Motor 13T 8/16 DP Spline SAE - D 4 Bolt Code 62 SAE Split Flange Cross Over Relief Not Equipped Planetary Four Stage Reduction Ratio 400:1 200MM Square Internal Oil Capacity Gallons Shaft Pull Out (lbs.) 300,000 lbs. BELOW CHART FOR LOW TORQUE/HIGH SPEED OUTPUT REFERENCE TORQUE CHART (LT / HS) Low Torque (119cc) Up To 2900 psi Note: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage BELOW CHART FOR HIGH TORQUE/LOW SPEED OUTPUT REFERENCE TORQUE CHART (HT / LS) High Torque (225cc) Up To 3100 psi THE DRIVE YOU NEED TO GET THE JOB DONE! 200MM Square lbs. TruLink Class 4 with 8" Monitor Part No Low 147cc High 225cc 80 (302) (370) (378) (416) (454) 7 5 ANCHOR DRIVES

30 TRULINK TORQUE MONITOR PAGE 30 TruLink Torque Monitor System is a revolutionary approach to collecting installation data associated with helical pile projects. The TruLink system is made up of a torque pin and your choice of 4" or 8" monitor (4" monitor not available on the Class 3 and 4 systems). FOR ALL REVOLUTION SERIES ANCHOR DRIVE UNITS CLASS 1-45MM Pin and Choice of Monitor Max Torque 20,000 ft/lb Part No mm Pin and 4" Monitor Part No mm Pin and 8" Monitor CLASS 2-75MM Pin and Choice of Monitor Max Torque 70,000 ft/lb Part No mm Pin and 4" Monitor Part No mm Pin and 8" Monitor CLASS 3-100MM Pin and 8" Monitor Max Torque 150,000 ft/lb Part No mm Pin and 8" Monitor CLASS 4-4.5" Pin and 8" Monitor Max Torque 300,000 ft/lb Part No mm Pin and 8" Monitor PROVIDES THE PRODUCTIVITY AND ACCURACY YOU DESERVE ON THE JOB SITE! 4" or 8" Easy to Read, Touch Screen Display Displays Time/Date, Torque, Depth and Pile Number Easily Mounts Inside Operators Cab ip67 Display Housing Rugged, Weatherproof and Shock-Resistant Simple Power Supply Adapter uses Auxiliary Power Port, Cigarette Lighter The TruLink Torque Monitor system offers true torque readings that deliver a high degree of accuracy (+/- 2%) while providing the operator with real time data. TruLink records actual torque being applied to the helical pile, the installation angle and the depth. Unlike other torque monitoring systems available, TruLink isolates torque values only. Downward and side load forces are omitted ensuring the data is clean. ACCESSORIES Pengo offers "Ear Kits" so that you may use TruLink on non-revolution Series Drive units. Class 1 Ear Kit Part No Class 2 Ear Kit Part No Replaces Connection Pin No Added Weight or Height or Loss of Stroke Built-in Inclinometer Allows Operator to Maintain a Consistent Angle of Insertion All Data is Recorded Within the Display No Laptop Required to Extract Data Downward (perpendicular) Force is Omitted with Patent Pending Technology Isolating Torque Values Strain Gage Technology Not Inferred or Calculated as With Hydraulic Systems Hard Wired Connection Eliminates Interference and Signal Issues Encountered with Wireless Systems Ability to Chart and Record Depth for Each Pile

31 PAGE 31 DRIVE MOUNTS UNIVERSAL SKID LOADER MOUNT LONG REACH UNIVERSAL SKID MOUNT Part No lbs. UNIVERSAL SKID MOUNT Part No lbs. Attachment Plate connects to the mounting plate on the front of the Skid Loader. The Link Arm connects to both the Attachment Plate and the Drive Unit with the supplied connection pins. Attachment Plate connects to the mounting plate on the front of the Skid Loader. The Link Arm connects to both the Attachment Plate and the Drive Unit with the supplied connection pins. Max. Torque Capacity is 12,000 ft/lbs. Mount shown with DS-2 Drive. Mount shown with DS-2 Drive. BACKHOE LOADER & MOUNT END OF BOOM MOUNT Part No. Model Specific - Call for details QUICK COUPLER MOUNT Part No. Model Specific - Call for details Mounting Bracket connects directly to the boom with the customer supplied connection pin. The Drive Unit connects to the Mounting Bracket with the supplied connection pin. HEX FLANGE ADAPTERS H-250 Part No H-300 Part No H-400 Part No Mounting Bracket connects to the quick coupler when the jaws of the quick coupler engage the pins on the Mounting Bracket. The Link Arm connects to both the Mounting Bracket and the Drive Unit with the supplied connection pins. ACCESSORIES

DV-20 DRILLING DRIVE TRULINK TORQUE PIN DRIVES 12T - 20T 20'

DV-20 DRILLING DRIVE TRULINK TORQUE PIN DRIVES 12T - 20T 20' DV-20 DRILLING DRIVE VARIABLE SPEED DRIVE UNIT PN 610442 EXCAVATOR SIZE 12T - 20T MAX HOLE DEPTH 20' Removable Top Section CONNECTIONS HEX MAX HOLE DIA. 6' Motor Equipped with Quick Powerful & Efficient

More information

RS-6X ANCHOR DRIVE. TRULINK TORQUE PIN Not applicable with this model. DRIVES

RS-6X ANCHOR DRIVE. TRULINK TORQUE PIN Not applicable with this model. DRIVES RS-6X ANCHOR DRIVE SINGLE SPEED DRIVE UNIT PN 610659 used for anchor installation EXCAVATOR SIZE NA WEIGHT LBS 87 Highly Efficient Gearbox designed for long duty cycles CONNECTIONS HEX NOT RECOMMENDED

More information

RS-6X ANCHOR DRIVE. TRULINK TORQUE PIN Not applicable with this model. DRIVES

RS-6X ANCHOR DRIVE. TRULINK TORQUE PIN Not applicable with this model. DRIVES RS-6X ANCHOR DRIVE SINGLE SPEED DRIVE UNIT PN 610659 used for anchor installation EXCAVATOR SIZE NA WEIGHT LBS 87 Highly Efficient Gearbox designed for long duty cycles CONNECTIONS NOT RECOMMENDED FOR

More information

EXCAVATOR AUGERS. FOR USE ON THE FOLLOWING CARRIES Excavators

EXCAVATOR AUGERS. FOR USE ON THE FOLLOWING CARRIES Excavators FOR USE ON THE FOLLOWING CARRIES Excavators PENGO AUGER SOIL CHART Pengo has developed the chart below to help you decide which auger will be best suited for your project. The above triangles and color

More information

800.599.0211 Foundation Tooling and ACIP WA MT ND ME OR CA NV ID WEST UT WY CO MN SD NE IA NORTH KS MO WI IL MI IN OH WV KY EAST PA VA VT NH NY MA CT NJ RI DE MD AZ NM OK AR TN SC NC AK TX SOUTH LA MS

More information

ELECTRICAL KIT - TC PM

ELECTRICAL KIT - TC PM ELECTRICAL KIT - TC-000013 PM-000080 1 TO THE PURCHASER Congratulations on the purchase of your new DIGGA Electrical Kit! This product was carefully designed and manufactured to give you years of dependable

More information

AUGERS For Skid-Steer Loaders, Compact Tractors, Mini Compact Loaders, Excavators, Mini Excavators, Tractor Loader Backhoes and Telehandlers

AUGERS For Skid-Steer Loaders, Compact Tractors, Mini Compact Loaders, Excavators, Mini Excavators, Tractor Loader Backhoes and Telehandlers AUGERS For Skid-Steer Loaders, Compact Tractors, Mini Compact Loaders, Excavators, Mini Excavators, Tractor Loader Backhoes and Telehandlers The McMillen Auger Drives by Paladin, feature a wide variety

More information

ds-2 ds-3 rs-7 rs-7x rs-12

ds-2 ds-3 rs-7 rs-7x rs-12 Manual ID: Drive Manual RS Series.indd Release Date: March, 19 2012 Printed in the USA Owner s Manual Parts Manual Safety Precautions Operating Instructions Maintenance SINGLE SPEED MODELS: ds-2 ds-3 rs-7

More information

1 TO THE PURCHASER THANK YOU ABOUT THIS MANUAL

1 TO THE PURCHASER THANK YOU ABOUT THIS MANUAL PM-000041-F 2 PM-000041-F Diggalign Operators Manual - August 2015 1 TO THE PURCHASER THANK YOU Congratulations on the purchase of your new DIGGA product! This product was carefully designed and manufactured

More information

SINGLE SPEED MODELS: Cs-1 Cs-2 cs-3 cs-4

SINGLE SPEED MODELS: Cs-1 Cs-2 cs-3 cs-4 Manual ID: Drive Manual CS Series.indd Release Date: April 16, 2018 Printed in the USA Owner s Manual Parts Manual Safety Precautions Operating Instructions Maintenance SINGLE SPEED MODELS: Cs-1 Cs-2 cs-3

More information

AUGERS For Skid-Steer Loaders, Compact Tractors, Mini Compact Loaders, Excavators, Mini Excavators, Tractor Loader Backhoes and Telehandlers

AUGERS For Skid-Steer Loaders, Compact Tractors, Mini Compact Loaders, Excavators, Mini Excavators, Tractor Loader Backhoes and Telehandlers AUGERS For Skid-Steer Loaders, Compact Tractors, Mini Compact Loaders, Excavators, Mini Excavators, Tractor Loader Backhoes and Telehandlers The McMillen Auger Drives by Paladin, feature a wide variety

More information

VARIABLE SPEED MODELS: RV-100 RV-150 RV-200 RV-300

VARIABLE SPEED MODELS: RV-100 RV-150 RV-200 RV-300 Manual ID: Drive Manual RV Series.indd Release Date: March 6, 2015 Printed in the USA Owner s Manual Parts Manual Safety Precautions Operating Instructions Maintenance VARIABLE SPEED MODELS: RV-100 RV-150

More information

There s no better choice

There s no better choice There s no better choice Well known as the original source of the In-Line Drive Design, Premier Auger has built the most reliable earth auger attachments for over 3 decades. With a complete and comprehensive

More information

1 TO THE PURCHASER TABLE OF CONTENTS SERVICE & PREPARATION... 5

1 TO THE PURCHASER TABLE OF CONTENTS SERVICE & PREPARATION... 5 SAFETY ALERT SYMBOL This is the Safety Alert Symbol used by this industry. This symbol is used to warn of possible injury. Be sure to read all warnings carefully. They are included for your safety and

More information

SINGLE SPEED MODELS: MS-100 MS-125

SINGLE SPEED MODELS: MS-100 MS-125 Manual ID: Drive Manual MS Series.indd Release Date: March, 19 2012 Printed in the USA Owner s Manual Parts Manual Safety Precautions Operating Instructions Maintenance SINGLE SPEED MODELS: MS-100 MS-125

More information

VARIABLE SPEED MODELS: dv-20 DV-30 DV-40

VARIABLE SPEED MODELS: dv-20 DV-30 DV-40 Manual ID: Drive Manual RV Series.indd Release Date: March 17, 2018 Printed in the USA Owner s Manual Parts Manual Safety Precautions Operating Instructions Maintenance VARIABLE SPEED MODELS: dv-20 DV-30

More information

ds-2 ds-3 rs-6x rs-6 rs-7 rs-7x rs-12

ds-2 ds-3 rs-6x rs-6 rs-7 rs-7x rs-12 Manual ID: Drive Manual RS Series.indd Release Date: June, 18 2015 Printed in the USA Owner s Manual Parts Manual Safety Precautions Operating Instructions Maintenance SINGLE SPEED MODELS: ds-2 ds-3 rs-6x

More information

Price quote for: Aftermarket Tractor/Skidsteer Attachments

Price quote for: Aftermarket Tractor/Skidsteer Attachments SEQ. #416-713 MINNESOTA PRICING PAGES (Typed Your Responses Required in Yellow Cells JULY, 2013 Price quote for: Vendor Name: Contact Person: Street Address: P.O. Box: City, State, Zip Phone #: Toll Free

More information

BACKHOES. Universal quick attach/mainframe mount

BACKHOES. Universal quick attach/mainframe mount BACKHOES For Skid Steer Loaders, Compact Tool Carriers, Compact Tractors and Compact Tractor Loaders Bradco Backhoes, by Paladin, are designed to fit compact tractors, compact tractor loaders, compact

More information

TRENCHER ATTACHMENTS AUGER TORQUE USA LLC USA - ISSUE

TRENCHER ATTACHMENTS AUGER TORQUE USA LLC USA - ISSUE TRENCHER ATTACHMENTS AUGER TORQUE USA LLC USA - ISSUE 11.1 www.augertorqueusa.com The laborious task of digging a trench has been transformed since the advent of the Trencher Attachment. Auger Torque s

More information

Bobcat Backhoe Attachments

Bobcat Backhoe Attachments Backhoe Attachments M06 4 Bobcat Backhoe Attachments Turn your loader into a powerful part-time excavator. Ideal for landscaping, nursery work, sewage systems, septic tanks, water lines, power lines and

More information

There s no better choice than Premier.

There s no better choice than Premier. There s no better choice than Premier. PREMIER POWER Premier Agricultural Attachments are designed to utilize the power of the host machine most efficiently, turning them into high performance work tools.

More information

PRODUCTIVE COST-EFFECTIVE RUGGED VERSATILE

PRODUCTIVE COST-EFFECTIVE RUGGED VERSATILE PRODUCTIVE COST-EFFECTIVE RUGGED VERSATILE { } GANNON the industry workhorse HEAVY-DUTY BUCKETS SEVERE-DUTY BUCKETS DITCHING & GRADING BUCKETS LOADER BUCKETS SPECIALTY BUCKETS BOX SCRAPERS QUICK CHANGE

More information

COMPACT TRACTOR ATTACHMENTS

COMPACT TRACTOR ATTACHMENTS COMPACT TRACTOR ATTACHMENTS For Compact Tractors with Universal Skid-Steer Hitch Paladin Attachments is your single source for high quality Compact Tractor Attachments landscapers. Paladin offers a variety

More information

OPERATOR'S & PARTS MANUAL

OPERATOR'S & PARTS MANUAL 1. OPERATOR'S & PARTS MANUAL FOR MINI TILT ATTACH PLATE INSTRUCTIONS NUMBER: 76214 1.888.888.1085 I www.spartanequipment.com Joppa, MD 21085 United States of America 2. TILT ATTACH ASSEMBLY 10522 3-7 -06

More information

Talet Equipment International Ltd. Sand Kicker

Talet Equipment International Ltd. Sand Kicker Talet Equipment International Ltd. Sand Kicker Parts & Operators Manual P.O. Box 35 Strathmore AB Canada TP K3 www.taletattachments.com sales@taletattachments.com Toll Free -888-37-5878 Fax -403-934-304

More information

SCREW ANCHOR & FOUNDATION DRIVES

SCREW ANCHOR & FOUNDATION DRIVES SCREW ANCHOR & FOUNDATION DRIVES MACHINERY ATTACHMENTS NORTH AMERICA 1 17-01 WE ARE DRIVEN TO MAKE YOU SUCCEED WITH PROVEN EXPERTISE IN PROVIDING MACHINERY ATTACHMENT SOLUTIONS. 2 A TRUSTED REPUTATION

More information

Attachments For Compact Tractors with Universal Skid-Steer Hitch

Attachments For Compact Tractors with Universal Skid-Steer Hitch compact Tractor Attachments Compact Tractor Attachments For Compact Tractors with Universal Skid-Steer Hitch Paladin offers a variety of attachments for Compact Tractors ranging in size, capability, and

More information

Part Number: MODEL NUMBER: Rev. 7

Part Number: MODEL NUMBER: Rev. 7 609 & 6 POWER BACKHOES PARTS MANUAL SERIAL NUMBER: Manual Number: PM557 Part Number: 75457 MODEL NUMBER: Rev. 7 800-922-298 I www.paladinbrands.com P.O. Box 266, Delhi, IA 5222-0266, United States of America

More information

Attachments for Excavators

Attachments for Excavators Attachments for Excavators BOBCAT ATTACHMENTS FOR EXCAVATORS FOR 323, 325, 329, 331, 331E*, 335, 337, 425, 430, 435 AUGER FOR 323, 325, 329, 331, 331E*, 335, 337, 418, 425, 430, 435, 442 BREAKER Whether

More information

UTILITY AUGERS. FOR USE ON THE FOLLOWING CARRIES Mini Digger Derricks, Digger Derricks and Pressure Diggers

UTILITY AUGERS. FOR USE ON THE FOLLOWING CARRIES Mini Digger Derricks, Digger Derricks and Pressure Diggers FOR USE ON THE FOLLOWING CARRIES Mini Digger Derricks, Digger Derricks and Pressure Diggers PENGO AUGER SOIL CHART Pengo has developed the chart below to help you decide which auger will be best suited

More information

COMPACT EXCAVATORS ZERO-TAIL-SWING 170Z 270Z 350Z 450Z 800Z

COMPACT EXCAVATORS ZERO-TAIL-SWING 170Z 270Z 350Z 450Z 800Z COMPACT EXCAVATORS ZERO-TAIL-SWING 170Z 270Z 350Z 450Z 800Z IN THE BEGINNING What began in the 19th century as an agricultural implement manufacturer has grown into a 21st century compact equipment powerhouse

More information

POST HOLE DIGGER. Operation, Service & Parts Manual For Models D20 & D40. FORM: D20_40DigRev.QXD

POST HOLE DIGGER. Operation, Service & Parts Manual For Models D20 & D40. FORM: D20_40DigRev.QXD POST HOLE DIGGER Operation, Service & Parts Manual For Models D20 & D40 FORM: D20_40DigRev.QXD September 2006 Revised August 2009 TABLE OF CONTENTS Introduction.............................1 Preparation..............................2

More information

OPERATIONS AND MAINTENANCE

OPERATIONS AND MAINTENANCE HELITILT OPERATIONS AND MAINTENANCE JB ATTACHMENTS - WHEN ONLY THE BEST WILL DO! INCREASE PRODUCTIVITY PROFITABILITY VERSATILITY CONTENTS 1.0 INTRODUCTION 1.0-1.4 2.0 SAFETY INSTRUCTIONS 2.0-2.5 3.0 STANDARDS

More information

VIS (Valve-In-Star) Hydraulic Motor

VIS (Valve-In-Star) Hydraulic Motor VIS (Valve-In-Star) Hydraulic Motor VIS 30 Series VIS 40 Series VIS 45 Series The next step in the evolution of low speed high torque (LSHT) hydraulic motors. EATON Low Speed High Torque Motors E-MOLO-MC001-E5

More information

M06For MT52 and. Maximum digging depth of more than 6 ft. Narrow width for working in tight areas. quick and easy attachment changes.

M06For MT52 and. Maximum digging depth of more than 6 ft. Narrow width for working in tight areas. quick and easy attachment changes. Backhoe Attachment Backhoe Attachment Digging Power. Ground Clearance. M06For MT52 and MT55 Loaders Maximum digging depth of more than 6 ft. Narrow width for working in tight areas. Combination Bob-Tach

More information

UTILITY AUGERS. FOR USE ON THE FOLLOWING CARRIES Mini Digger Derricks, Digger Derricks and Pressure Diggers

UTILITY AUGERS. FOR USE ON THE FOLLOWING CARRIES Mini Digger Derricks, Digger Derricks and Pressure Diggers FOR USE ON THE FOLLOWING CARRIES Mini Digger Derricks, Digger Derricks and Pressure Diggers PENGO AUGER SOIL CHART Pengo has developed the chart below to help you decide which auger will be best suited

More information

25GT Compact Tool Carrier

25GT Compact Tool Carrier 25GT Compact Tool Carrier Big machine performance in a small package The compact Thomas 25GT is designed to get you to your work no matter how tight the quarters. And, when you get there, the 25GT has

More information

CAT MINI EXCAVATOR ATTACHMENT OPTIONS

CAT MINI EXCAVATOR ATTACHMENT OPTIONS CAT MINI EXCAVATOR ATTACHMENT OPTIONS Get Multiple Machines Out of One For more information, visit Cat.com/attachments or contact your local Cat dealer. AEXQ1584-02 March 2018 2018 Caterpillar. All Rights

More information

TRENCHER ATTACHMENTS AUGER TORQUE NEW ZEALAND NEW ZEALAND - ISSUE

TRENCHER ATTACHMENTS AUGER TORQUE NEW ZEALAND NEW ZEALAND - ISSUE TRENCHER ATTACHMENTS AUGER TORQUE NEW ZEALAND NEW ZEALAND - ISSUE 10.1 www.augertorque.co.nz The laborious task of digging a trench has been transformed since the advent of the Trencher Attachment. Auger

More information

OPERATOR S AND PARTS MANUAL PALLET FORKS. Part Number: MODEL NUMBER: Rev. 4

OPERATOR S AND PARTS MANUAL PALLET FORKS. Part Number: MODEL NUMBER: Rev. 4 OPERATOR S AND PARTS MANUAL PALLET FORKS SERIAL NUMBER: Manual Number: OM642 Part Number: 75542 MODEL NUMBER: Rev. 4 800-456-7100 I www.paladinlcg.com 503 Gay Street, Delhi, IA 52223, United States of

More information

Talet Equipment International Ltd. Sanding Auger Bucket

Talet Equipment International Ltd. Sanding Auger Bucket Talet Equipment International Ltd. Sanding Auger Bucket Parts & Operators Manual P.O. Box 35 Strathmore AB Canada TP K3 www.taletattachments.com sales@taletattachments.com Toll Free -888-37-5878 Fax -403-934-304

More information

Backhoe Range. For Tractors from 15HP

Backhoe Range. For Tractors from 15HP Backhoe Range For Tractors from 15HP LEWIS Backhoe Range The LEWIS range of backhoes are specifically designed to fit most makes of tractors from 15HP compact tractors up to 60+HP agricultural tractors.

More information

Product Catalogue. Version

Product Catalogue. Version Product Catalogue Version 1.0-2017 sales@lionforgeindustries.com An Introduction to Simplement The Simplement System is our Patent Pending receiver/hitch unit and modular implement system. This product

More information

SOLAR DASH CHARGING SYSTEM USER GUIDE

SOLAR DASH CHARGING SYSTEM USER GUIDE SOLAR DASH CHARGING SYSTEM Doc 1.01 INST049 INSTALLATION STEP 1 Place 20 watt solar panel in the dash of the vehicle facing up. Note: For ideal results position the vehicle in a manner in which the solar

More information

TRU-TIME ADJUSTABLE CAM GEAR Part Number: BK & BK

TRU-TIME ADJUSTABLE CAM GEAR Part Number: BK & BK TRU-TIME ADJUSTABLE CAM GEAR Part Number: 23-801BK & 23-802BK! WARNING: This installation is not for the mechanically challenged! If you are not mechanically inclined or do not understand the procedure

More information

Excavators. Mini/Midi

Excavators. Mini/Midi Mini/Midi Excavators Hitches 1 Buckets 2-6 Earth Drills 7 Breakers 8 Hand Held Tools 9-12 Compactors 12 Rock Wheel 13 Ripper Tooth 13 Selector Grabs 13 Mini/Midi Excavators Introduction Mini/Midi Excavators

More information

Ditch Witch 420sx, 410sx, 100sx, Zahn R300, Zahn R230 VIBRATORY PLOWS. ditchwitch.com

Ditch Witch 420sx, 410sx, 100sx, Zahn R300, Zahn R230 VIBRATORY PLOWS. ditchwitch.com Ditch Witch 420sx, 410sx, 100sx, Zahn R300, Zahn R230 VIBRATORY PLOWS ditchwitch.com CMWC-1441_REV_VibPlows_V7.indd 1 feel the earth move. ditchwitch.com CMWC-1441_REV_VibPlows_V7.indd 2-3 ditch witch

More information

CAT MINI EXCAVATOR ATTACHMENT OPTIONS

CAT MINI EXCAVATOR ATTACHMENT OPTIONS CAT MINI EXCAVATOR ATTACHMENT OPTIONS Get Multiple Machines Out of One For more information, visit Cat.com/attachments or contact your local Cat dealer. AEXQ1584-01 December 2015 2015 Caterpillar. All

More information

Lubricant and Coolant Capacity

Lubricant and Coolant Capacity Engine Isuzu AI-4HK1X Tier 3 turbocharged diesel engine with electronic fuel control, 153 Net HP (114 kw), 5.2 Liter displacement, 4-cylinder, water-cooled, EGR with cooler, air-toair intercooler, 24-volt

More information

DITCH WITCH RT55, RT40, RT36 RT TRACTORS

DITCH WITCH RT55, RT40, RT36 RT TRACTORS DITCH WITCH RT55, RT40, RT36 RT TRACTORS MAKING SHOVELS OBSOLETE SINCE 1949. DITCH WITCH. DITCH WITCH RT55 TRACTOR Our rugged line of RT tractors gives you the punch you need to dig through some of the

More information

Pick Up Broom OWNERS/OPERATORS MANUAL. Model Number. Serial Number. Date of Manufacture. To Serial # Phone:

Pick Up Broom OWNERS/OPERATORS MANUAL. Model Number. Serial Number. Date of Manufacture. To Serial # Phone: Pick Up Broom OWNERS/OPERATORS MANUAL Model Number. Serial Number. Date of Manufacture. To Serial #039 Phone: 77-37-6 //0 Warranty Skid Pro products are warranted to be free from defects, in workmanship,

More information

RANCHHO GX BACKHOES CHIPPERS / SHREDDERS BACKHOES

RANCHHO GX BACKHOES CHIPPERS / SHREDDERS BACKHOES RANCHHO GX S BREAK GROUND, NOT YOUR BACK When it comes to landscaping and excavating, start the job right with the Wallenstein Ranchho, the backhoe attachment that digs deeper and reaches further. CHIPPERS

More information

PRODUCT GUIDE. ENGLISH ISSUE 12-1 AUGER TORQUE EUROPE LTD

PRODUCT GUIDE.   ENGLISH ISSUE 12-1 AUGER TORQUE EUROPE LTD PRODUCT GUIDE ENGLISH AUGER TORQUE EUROPE LTD ISSUE 12-1 www.augertorque.com A Customer-Driven Global Company Established in Europe in 1998, Auger Torque has created a new standard in the Earth Drill and

More information

AGRICULTURE ATTACHMENTS

AGRICULTURE ATTACHMENTS AGRICULTURE ATTACHMENTS TACKLE MORE TASKS WHILE MITIGATING COSTS WITH YOUR CAT MACHINE. Cat Skid Steer Loaders, Multi Terrain Loaders, Compact Track Loaders, Compact Wheel Loaders, Backhoe Loaders, Small

More information

COMPACT EXCAVATORS 80M 170Z NXT2 250Z 350Z NXT2 450Z NXT2 550Z 800Z NXT2 1000M

COMPACT EXCAVATORS 80M 170Z NXT2 250Z 350Z NXT2 450Z NXT2 550Z 800Z NXT2 1000M COMPACT EXCAVATORS 80M 170Z 250Z 350Z 450Z 550Z 800Z 1000M A LEGACY OF INNOVATION WHAT BEGAN IN THE 19TH CENTURY AS AN AGRICULTURAL IMPLEMENT MANUFACTURER HAS GROWN INTO A 21ST CENTURY EQUIPMENT POWERHOUSE

More information

M06For MT52 and. Maximum digging depth of more than 6 ft. Narrow width for working in tight areas.

M06For MT52 and. Maximum digging depth of more than 6 ft. Narrow width for working in tight areas. BACKHOE ATTACHMENT Backhoe Attachment Digging Power. Ground Clearance. Efficient. Economical. Versatile. Now your multi-job Bobcat loader can become even more of a time-saving workhorse when you add the

More information

AGRICULTURE ATTACHMENTS TACKLE MORE TASKS WHILE MITIGATING COSTS WITH YOUR CAT MACHINE.

AGRICULTURE ATTACHMENTS TACKLE MORE TASKS WHILE MITIGATING COSTS WITH YOUR CAT MACHINE. AGRICULTURE ATTACHMENTS TACKLE MORE TASKS WHILE MITIGATING COSTS WITH YOUR CAT MACHINE. Cat Skid Steer Loaders, Multi Terrain Loaders, Compact Track Loaders, Compact Wheel Loaders, Backhoe Loaders, Small

More information

JCB ATTACHMENTS FOR MINI AND MIDI EXCAVATORS A class-leading range of attachments suitable for mini and midi excavators.

JCB ATTACHMENTS FOR MINI AND MIDI EXCAVATORS A class-leading range of attachments suitable for mini and midi excavators. JCB ATTACHMENTS FOR MINI AND MIDI EXCAVATORS A class-leading range of attachments suitable for mini and midi excavators. #completingthesolution www.jcb.com AREAS OF APPLICATION. QUICK HITCHES. CONTENTS

More information

200 SERIES COMPACT TRACK LOADERS

200 SERIES COMPACT TRACK LOADERS 200 SERIES COMPACT TRACK LOADERS Built Around You Introducing the new 200 Series compact track loaders. With five years in the making, they re bigger, badder and better! New Holland engineers used input

More information

35DT Compact Tool Carrier

35DT Compact Tool Carrier 35DT Compact Tool Carrier 620 lb(281 kg) Lift Capacity Big machine performance in a small package The compact Thomas 35DT is designed to get you to your work no matter how tight the quarters. And, when

More information

Mulching. Attachments BULL HOG FORESTRY MULCHERS

Mulching. Attachments BULL HOG FORESTRY MULCHERS BULL HOG Mulching Attachments FORESTRY MULCHERS The Bull Hog Durability Fecon s Bull Hogs provide durability that is known and expected in the mulching industry. Leading with the strongest Severe-Duty

More information

Mini/Midi Excavator Attachments Guide ATTACHMENTS

Mini/Midi Excavator Attachments Guide ATTACHMENTS Mini/Midi Excavator Attachments Guide ATTACHMENTS Introduction Contents Our Range JCB s range of Mini/Midi Excavator equipment is expanding and so are the attachments to complement this range. JCB attachments

More information

September 2018 Price List

September 2018 Price List September 2018 Price List Page F8 Digger 3-5 J20/80 & G20/40 Diggers 6-8 Hammer CB40 9 Postmaster 10-11 Display Stands 12-13 Auger Bucket 14-15 Hammer Series 16-18 Intimidator 19 EP Heavy-Duty Auger Series

More information

HIGH DUMP ROLL-OUT BUCKET

HIGH DUMP ROLL-OUT BUCKET HIGH DUMP ROLL-OUT BUCKET Model # Serial # Rev. 01/14 Rylind Manufacturing, Inc. 2801 Youngfield St Suite 250 Golden, CO 80401 Business/Sales Offices: 303-979-3548 Manufacturing Plant: 970-522-2859 www.rylind.com

More information

FULL LINE COMPACT EXCAVATORS Z17 Z27 Z35 GEN:2 Z45 Z80

FULL LINE COMPACT EXCAVATORS Z17 Z27 Z35 GEN:2 Z45 Z80 FULL LINE COMPACT EXCAVATORS Z17 Z27 Z35 GEN:2 Z45 Z80 In 1859, an agricultural implement company, housed in a blacksmith shop, was started in West Bend, Wisconsin. From these humble beginnings, the Gehl

More information

TRIPLEX ROLLER / SPIKER HEADS MANUAL

TRIPLEX ROLLER / SPIKER HEADS MANUAL TRIPLEX ROLLER / SPIKER HEADS MANUAL Revised 3/Nov/2012 Contents MACHINE INFORMATION RECORD... 1 SAFETY INFORMATION... 2 WARRANTY... 3 OPERATION... 4 JOHN DEERE 2500... 5 JACOBSEN 4... 7 JACOBSEN 5 &

More information

FALKEN TIRE LIMITED WARRANTY

FALKEN TIRE LIMITED WARRANTY For questions: technical@falkentire.com Effective February 1, 2016 FALKEN TIRE LIMITED WARRANTY I. Tires Covered by this Warranty: This limited warranty applies to FALKEN brand steel belted radial passenger

More information

VersaHANDLER Telescopic Tool Carriers

VersaHANDLER Telescopic Tool Carriers VersaHANDLER Telescopic Tool Carriers Bobcat VersaHANDLER TTC The VersaHandler Telescopic Tool Carrier combines the speed, agility and strength of a skid-steer with extended reach to handle a wide variety

More information

SC series Stopper Cylinders

SC series Stopper Cylinders SERIES 60,000 PSI tensile strength electro-less nickel rod bearing High strength threaded connection Hard chrome plated 100,000 PSI yield strength rod inc plated dust cover series Stopper Cylinders Common

More information

SC series Stopper Cylinders

SC series Stopper Cylinders High strength threaded connection Low friction cup sealintegral rod wiper Double wound 302 SS retaining wire 60,000 PSI tensile strength electro-less nickel rod bearing Low friction figure 8 piston seal

More information

PRODUCT GUIDE. ENGLISH ISSUE 13-1 AUGER TORQUE EUROPE LTD

PRODUCT GUIDE.  ENGLISH ISSUE 13-1 AUGER TORQUE EUROPE LTD PRODUCT GUIDE ENGLISH AUGER TORQUE EUROPE LTD ISSUE 13-1 www.augertorque.com A Customer-Driven Global Company Established in Europe in 1998, Auger Torque has created a new standard in the Earth Drill and

More information

Read this entire manual before operation begins.

Read this entire manual before operation begins. Read this entire manual before operation begins. Record below the following information which is located on the serial number data plate. Serial No. Model No. Date of Installation Contents Specifications.............

More information

ROTARY TILLER. Operation, Service & Parts Manual For "AS" Series. FORM: ASTillerBook.QXD

ROTARY TILLER. Operation, Service & Parts Manual For AS Series. FORM: ASTillerBook.QXD ROTARY TILLER Operation, Service & Parts Manual For "AS" Series FORM: ASTillerBook.QXD April 2002 TABLE OF CONTENTS Preparation......................................1 Assembly Instructions.............................2

More information

INSTALLATION INSTRUCTIONS FOR M.O.R.E. SHACKLE REVERSAL SYSTEM (S.R.S. ) PART # THIS SYSTEM FITS Jeep CJ-5, CJ-7, CJ-8 VEHICLES.

INSTALLATION INSTRUCTIONS FOR M.O.R.E. SHACKLE REVERSAL SYSTEM (S.R.S. ) PART # THIS SYSTEM FITS Jeep CJ-5, CJ-7, CJ-8 VEHICLES. INSTALLATION INSTRUCTIONS FOR M.O.R.E. SHACKLE REVERSAL SYSTEM (S.R.S. ) PART # 7686-6 THIS SYSTEM FITS 1976-1986 Jeep CJ-5, CJ-7, CJ-8 VEHICLES. Please read all instructions carefully (including terms-policies)

More information

Operation and Parts Manual

Operation and Parts Manual Operation and Parts Manual 3-Point PTO and Hydraulic Stump Grinders Models: SC-25 and SC-25H SC-50 and SC-50H Safety Operation Maintenance Repair Troubleshooting Parts Parts SC-50 and SC-50-H Stumpbuster

More information

Power Wheel Model 8 Planetary Gear Drives AuburnGear.com

Power Wheel Model 8 Planetary Gear Drives AuburnGear.com Power Wheel Model 8 Planetary Gear Drives 260.92.30 AuburnGear.com MODEL 8 Features & A2 Integral Brake Information...3 MODEL 8 WHEEL DRIVES Double Reduction...4 with A2 Series Integral Parking Brake...6

More information

AGRICULTURE ATTACHMENTS

AGRICULTURE ATTACHMENTS AGRICULTURE ATTACHMENTS TACKLE MORE TASKS WHILE MITIGATING COSTS WITH YOUR CAT MACHINE. Cat Skid Steer Loaders, Multi Terrain Loaders, Compact Track Loaders, Compact Wheel Loaders, Backhoe Loaders, Small

More information

BACKHOE. attachments

BACKHOE. attachments BACKHOE attachments Rear Stabilizers Improve Performance Increase your backhoe performance in a wide range of jobs with an optional set of frame-mounted rear stabilizers. Improves performance by transferring

More information

... Superior Performance and Value

... Superior Performance and Value 75XT SKID STEER 2 ... Superior Performance and Value Meet the Case 75XT, a high-performance skid steer built to meet the demands of hardworking businesses. This innovative skid steer boasts a revolutionary

More information

CITY OF ELBERTON, GEORGIA REQUEST FOR PROPOSAL. IMPORTANT NOTE: Indicate company name and RFP Title on the front of the sealed bid envelope.

CITY OF ELBERTON, GEORGIA REQUEST FOR PROPOSAL. IMPORTANT NOTE: Indicate company name and RFP Title on the front of the sealed bid envelope. CITY OF ELBERTON, GEORGIA REQUEST FOR PROPOSAL RFP TITLE Ride-on RTX 750 Quad Track Tractor ISSUE DATE November 12, 2018 DUE DATE November 26, 2018 2:00 p.m. IMPORTANT NOTE: Indicate company name and RFP

More information

Fence Building Attachments Consistently delivering high performance

Fence Building Attachments Consistently delivering high performance Designed. Engineered. Remarkable Value. Fence Building Attachments Consistently delivering high performance www.worksaver.com Engineered, Designed and Manufactured in the USA Our Post Hole Diggers Dig

More information

Grapple Kit Install & Grapple Bucket Manual

Grapple Kit Install & Grapple Bucket Manual Grapple Kit Install & Grapple Bucket Manual Model # Serial # Rev. 10/13 Rylind Manufacturing, Inc. 2801 Youngfield St Suite 250 Golden, CO 80401 Business/Sales Offices: 303-979-3548 Manufacturing Plant:

More information

TRENCHERS. Standard flow and high flow options available. Choose from various chain and teeth assemblies

TRENCHERS. Standard flow and high flow options available. Choose from various chain and teeth assemblies TRNRS Paladin ttachments is your single source for high quality attachments for skid steers, compact tool carriers, and excavators used for vegetation/land management, landscaping, soil preparation, material

More information

HYDRAULIC BREAKERS HB-6000

HYDRAULIC BREAKERS HB-6000 HYDRAULIC BREAKERS HB6000 +POWER REDUCED DOWNTIME = PLUS MORE WORK, MORE PROFIT AND DEPENDABLE PERFORMANCE Features and Benefits EQUALS It s a simple equation, whether you re tearing down a bridge, scaling

More information

Read this entire manual before operation begins.

Read this entire manual before operation begins. Read this entire manual before operation begins. Record below the following information which is located on the serial number data plate. Serial No. Model No. Date of Installation Contents Specifications.............

More information

485 BACKHOE PARTS MANUAL

485 BACKHOE PARTS MANUAL 85 BACKHOE PARTS MANUAL SERIAL NUMBER: Manual Number: PM08 Part Number: 5608 MODEL NUMBER: Rev. 800-56-00 I www.paladinlcg.com 50 Gay Street, Delhi, IA 5, United States of America 06 --0- Limited Warranty

More information

305 CR. Mini Hydraulic Excavator

305 CR. Mini Hydraulic Excavator 305 CR Mini Hydraulic Excavator Engine Power Gross 32 kw 43 hp Net 31.3 kw 42 hp Maximum Operating Weight With cab 4990 kg 11,000 lb With canopy 4940 kg 10,890 lb 305 CR Mini Hydraulic Excavator Designed

More information

LOGGING/FORESTRY PRODUCT OVERVIEW POWER TAKE-OFFS AND HYDRAULIC COMPONENTS

LOGGING/FORESTRY PRODUCT OVERVIEW POWER TAKE-OFFS AND HYDRAULIC COMPONENTS LOGGING/FORESTRY PRODUCT OVERVIEW POWER TAKE-OFFS AND HYDRAULIC COMPONENTS Muncie Power Products, Inc. is a proud manufacturer of power take-offs and fluid power components for applications within the

More information

TRENCH & CLAY DIGGERS

TRENCH & CLAY DIGGERS TRENCH & CLAY DIGGERS Website: www.apt-tools.com e-mail: info@apt-tools.com TDS-1047 Rev A CLAY AND TRENCH DIGGERS TOOL MAINTENANCE & REPAIR INFORMATION FIELD OPERATION: Before use: 1. Fill the reservoir

More information

OMNI GEAR TRACTOR POWERED IMPLEMENT GEARDRIVES

OMNI GEAR TRACTOR POWERED IMPLEMENT GEARDRIVES TRACTOR POWERED IMPLEMENT GEARDRIVES PHD-15 Series 1750 lb.-in. 198 Nm. Ratios: 3:1 Tapered, Ball, Needle Oil Cap: 25 oz. (0.7 L) 26 lbs. (11.8 kg) Power: 15 hp 11 kw Post Hole Digger Drives PHD-25 Series

More information

Prime Attachments & Custom Fab Brush Mower Owners/Operators Manual

Prime Attachments & Custom Fab Brush Mower Owners/Operators Manual Prime Attachments & Custom Fab Brush Mower Owners/Operators Manual The operator is responsible for the safe operation and maintenance of the machine. It is important that anyone who uses the machine is

More information

Group 8 - Compact Track Loaders and Attachments BOBCAT COMPANY SUGGESTED PRICE LIST Bobcat Company ORDER ADDRESS:

Group 8 - Compact Track Loaders and Attachments BOBCAT COMPANY SUGGESTED PRICE LIST Bobcat Company ORDER ADDRESS: Group 8 - Compact Track Loaders and Attachments BOBCAT COMPANY SUGGESTED PRICE LIST - 01-01-2018 Government Sales Points of Contact: Heather Messmer - Government Accounts Sales Support Mgr. heather.messmer@doosan.com

More information

INSTALLATION OPERATING SERVICE AND SAFETY INSTRUCTIONS

INSTALLATION OPERATING SERVICE AND SAFETY INSTRUCTIONS MODEL GE 970 Boom Mounted Compactor / Driver GENPAC INSTALLATION OPERATING SERVICE AND SAFETY INSTRUCTIONS PARTS LIST 1.0 INTRODUCTION The Genpac GE-970 is a boom-mounted hydraulic vibrating plate compactor

More information

BACKHOE LOADERS CONTENTS

BACKHOE LOADERS CONTENTS BACKHOE LOADERS CONTENTS Features...............................-1 Specifications...........................-3 416E:......................-6 Lift Capacities.........................-8 420E/420E IT:......................-9

More information

Power Wheel Model 8 Series B Planetary Gear Drives AuburnGear.com

Power Wheel Model 8 Series B Planetary Gear Drives AuburnGear.com Power Wheel Model 8 Series B Planetary Gear Drives 260.92.30 AuburnGear.com SERIES B WHEEL DRIVES Model 8 Series B Features & A2 Integral Brake Information...3 Double Reduction...4 with A2 Series Integral

More information

S305/S320 S325/S340 S365/S390

S305/S320 S325/S340 S365/S390 S305/S320 S325/S340 S365/S390 Mobile Scrap and Demolition Shears S320 312B L Reach Boom Mounted * Must be operated with Dozer blade and stabilizer down or two sets or stabilizers down. S325 318B L 320B

More information

ReelGreen RG20 Instruction Manual For Operation and Maintenance

ReelGreen RG20 Instruction Manual For Operation and Maintenance ReelGreen RG20 Instruction Manual For Operation and Maintenance BigSprinkler.com 15250 Sunshine Rd. Yukon, OK. 73099 800-373-9325 Introduction Thank you for purchasing a ReelGreen RG20 traveling sprinkler

More information

MINING FORESTRY MOBILE TRUCK AGRICULTURE MATERIAL HANDLING OPTIMUM

MINING FORESTRY MOBILE TRUCK AGRICULTURE MATERIAL HANDLING OPTIMUM MINING FORESTRY MOBILE TRUCK AGRICULTURE MATERIAL HANDLING OPTIMUM Muncie Power Products OPTIMUM Series gear pumps/motors offer premier performance for a wide variety of applications across several industries.

More information

SERIAL NUMBER: Manual Number: Part Number: MODEL NUMBER: Date: November 23, 2005

SERIAL NUMBER: Manual Number: Part Number: MODEL NUMBER: Date: November 23, 2005 OPERATOR S & PARTS MANUAL 3.00-4.00 CUBIC YARD BUCKETS SERIAL NUMBER: Manual Number: 76839 Part Number: 76839 MODEL NUMBER: Date: November 3, 005 800-9-981 I www.paladinbrands.com P.O. Box 66, Delhi, IA

More information