Technical Specifications

Transcription

1 320 Hydraulic Excavator Technical Specifications Engine Track Engine Model Cat C4.4 ACERT Standard with Long Undercarriage 70 mm 31 in Net Power (ISO 24) 121 kw 162 hp Number of Shoes (each side) 4 Net Power (SAE J134) 121 kw 162 hp Long Undercarriage Gross Power (ISO 1436/SAE J1) 122 kw 164 hp Number of Track Rollers (each side) 8 Long Undercarriage Bore 10 mm 4 in Number of Carrier Rollers (each side) 2 Stroke 127 mm in Displacement 4.4 L 26 in3 Drive The 320 meets U.S. EPA Tier 4 Final emission standards. Recommended for use up to 400 m altitude (14,764 ft) with Maximum Gradeability 3 /70% engine power derate above 3000 m (,842. ft). Maximum Travel Speed.7 km/h 3. mph Net power advertised is the power available at the flywheel when Maximum Drawbar Pull 20 kn 4,6 f the engine is equipped with fan, air cleaner, muffler and alternator. Long Undercarriage Rating at 1,800 rpm. Engine rpm Hydraulic System Main System Maximum Flow 42 L/min 113 gal/min Operation 1,60 rpm (Implement) (214. (6. Travel 1,800 rpm 2 pumps) 2 pumps) Swing System Maximum Flow No swing pump Swing Mechanism Maximum Pressure Equipment kpa,07 psi Swing Speed 11.2 rpm Normal Maximum Swing Torque 74 kn m 4,440 f-ft Maximum Pressure Equipment kpa,10 psi Lift Mode Weights Maximum Pressure Travel kpa 4,74 psi Maximum Pressure Swing kpa 3,886 psi Operating Weight ,100 Boom Cylinder Bore 120 mm in Long undercarriage, Reach boom, R2. ('6") stick, HD 1.1 m3 Boom Cylinder Stroke 1260 mm 0 in (1.6 yd3) bucket and 70 mm (31 in) triple grouser shoes, 4.2 mt (,300 ) counterweight. Stick Cylinder Bore 140 mm 6 in Stick Cylinder Stroke 104 mm in Bucket Cylinder Bore 120 mm in Bucket Cylinder Stroke 1104 mm 43 in

2 Service Refill Capacities Fuel Tank Capacity 34 L 86.6 gal Cooling System 3 L.2 gal Engine Oil Swing Drive (each) 1 L 7 L 4.0 gal 1.8 gal Final Drive (each) 6 L 1.6 gal Hydraulic System (including tank) 240 L 63.4 gal Hydraulic Tank 128 L 33.8 gal DEF Tank 40 L 10.6 gal Sound Performance ISO 63 (external) 7 db(a) ISO 636 (inside cab) 70 db(a) When properly installed and maintained, the cab offered by Caterpillar, when tested with doors and windows closed according to ANSI/SAE J1166 OCT8, meets OSHA and MSHA requirements for operator sound exposure limits in effect at time of manufacture. Hearing protection may be needed when operating with an open operator station and cab (when not properly maintained or doors/ windows open) for extended periods or in a noisy environment. Standards Brakes ISO 1026:2008 Cab/FOGS ISO 10262:18 Cab/ROPS ISO :2008 Operating Weight and Ground Pressure 70 mm (31 in) Triple Grouser Shoes Weight Ground Pressure 4.2 mt (,300 ) Counterweight + Long Undercarriage Base Machine Reach Boom + R2. ('6") Stick m3 (1.6 yd3) HD Bucket , kpa.2 psi All operating weights include a 0% fuel tank with 7 (16 ) operator. 2

3 Major Component Weights Base Machine (with 4.2 mt [,300 ] counterweight, semi-hd swing frame, standard base frame with ,600 HD track rollers and standard carrier rollers for long undercarriage, with boom cylinder does not include 0% fuel and 7 [16 ] operator) Track Shoes: 70 mm (31 in) Width, 10 mm (0.3 in) Thick Triple Grouser Track Shoes for Long Undercarriage ,400 with Step Extension for ISO 2867 Two Boom Cylinders Weight of 0% Fuel Tank and 7 (16 ) Operator Counterweights: 4.2 mt (,300 ) Counterweight 4200, mt (10,400 ) Counterweight (only for Super Long Reach) ,400 Swing Frame: Semi-HD Swing Frame, for C4.4 ACERT 110 4,210 Standard and Long Undercarriage: Standard Base Frame with HD Track Rollers and Standard Carrier Rollers for Long Undercarriage 430,700 Booms (including lines, pins, stick cylinder): Reach Boom (.7 m/18'8") ,800 Super Long Reach Boom (8.8 m/2'0") ,800 Sticks (including lines, pins, bucket cylinder, bucket linkage): Reach Stick (R2.B1/'6") ,00 Super Long Reach Stick (6.28A/20'7") ,000 Buckets (without linkage): 1.1 m3 (1.6 yd3) HD 880 1, m3 (1.31 yd3) HD 80 1, m3 (0.7 yd3) Ditch Cleaning Quick Couplers: Pin Grabber QC

4 Dimensions All dimensions are approximate and may vary depending on bucket selection , 10 2 Boom Options Reach Boom SLR Boom.7 m (18'8") 8.8 m (2'0") Stick Options Reach Stick SLR Stick R2.B1 ('6") 6.28A (20'7") 6.28A (20'7") 1 Machine Height: Top of Cab Height 260 mm '" 260 mm '" 260 mm '" Top of FOGS Height 3100 mm 10'2" 3100 mm 10'2" 3100 mm 10'2" Handrails Height 20 mm '8" 20 mm '8" 20 mm '8" With Boom/Stick/Bucket Installed 3160 mm 10'4" 310 mm 10'6" 310 mm 10'6" With Boom/Stick Installed 210 mm '7" 3070 mm 10'1" 3070 mm 10'1" With Boom Installed 2480 mm 8'2" 260 mm 8'8" 260 mm 8'8" 2 Machine Length: With Boom/Stick/Bucket Installed 30 mm 31'3" mm 41'" mm 41'" With Boom/Stick Installed 00 mm 31'2" mm 41'" mm 41'" With Boom Installed 840 mm 27'" 820 mm 2'3" 820 mm 2'3" 3 Upperframe Width without Walkways 2780 mm '1" 2780 mm '1" 2780 mm '1" 4 Tail Swing Radius 2830 mm '3" 2830 mm '3" 2830 mm '3" Counterweight Clearance 100 mm 3'" 100 mm 3'" 100 mm 3'" 6 Ground Clearance 470 mm 1'7" 470 mm 1'7" 470 mm 1'7" 7 Track Length Length to Center of Rollers 360 mm 12'0" 360 mm 12'0" 360 mm 12'0" 8 Track Gauge Extended 2380 mm 7'" 2380 mm 7'" 2380 mm 7'" Track Width: 70 mm (31 in) Shoes 3170 mm 10'" 3170 mm 10'" 3170 mm 10'" 10 Undercarriage Width (with steps/without steps): 70 mm (31 in) Shoes 3170 mm 10'" 3170 mm 10'" 3170 mm 10'" Bucket Type HD Ditch Cleaning (DC) GD Bucket Capacity 1.1 m3 1.6 yd3 0.7 m3 0.7 yd3 0.3 m3 0.6 yd3 Bucket Tip Radius 170 mm '2" 1070 mm 3'6" 1230 mm 4'0" 4

5 Working Ranges All dimensions are approximate and may vary depending on bucket selection. Feet 3 Meters R2.B1 ('6") Meters Feet Boom Option Reach Boom.7 m (18'8") Stick Option Reach Stick 1 Maximum Digging Depth R2.B1 ('6") 6720 mm 22'1" 2 Maximum Reach at Ground Line 860 mm 32'4" 3 Maximum Cutting Height 370 mm 30'" 4 Maximum Loading Height 640 mm 21'4" Minimum Loading Height 2170 mm 7'1" 6 Maximum Depth Cut for 2440 mm (8'0") Level Bottom 60 mm 21'6" 7 Maximum Vertical Wall Digging Depth 10 mm 17'0" Bucket Digging Force (SAE) 134 kn 2 f Bucket Digging Force (ISO) 10 kn 332 f Stick Digging Force (SAE) 103 kn 228 f Stick Digging Force (ISO) 106 kn 23 f Bucket Type HD Bucket Capacity 1.1 m3 1.6 yd3 Bucket Tip Radius 170 mm '2"

6 Working Ranges All dimensions are approximate and may vary depending on bucket selection. Feet 4 Meters A (20'7") Meters Feet Boom Option SLR Boom 8.8 m (2'0") Stick Option SLR Stick 6.28A (20'7") 6.28A (20'7") 1 Maximum Digging Depth mm 38'0" mm 38'4" 2 Maximum Reach at Ground Line 1 70 mm 1'1" mm 1'7" 3 Maximum Cutting Height mm 44'" mm 44'8" 4 Maximum Loading Height mm 37'6" mm 37'0" Minimum Loading Height 2240 mm 7'4" 2080 mm 6'" 6 Maximum Depth Cut for 2440 mm (8'0") Level Bottom mm 37'6" 11 0 mm 38'0" 7 Maximum Vertical Wall Digging Depth mm 36'2" mm 34'8" Bucket Digging Force (SAE) 62 kn 136 f 4 kn 11 f Bucket Digging Force (ISO) 62 kn 136 f 60 kn 133 f Stick Digging Force (SAE) 4 kn 108 f 48 kn 106 f Stick Digging Force (ISO) 4 kn 108 f 4 kn 107 f Bucket Type Ditch Cleaning (DC) GD Bucket Capacity 0.7 m3 0.7 yd3 0.3 m3 0.6 yd3 Bucket Tip Radius 1070 mm 3'6" 1230 mm 4'0" 6

7 Reach Boom Lift Capacities Counterweight: 4.2 mt (,300 ) without Bucket 2. m ('6").7 m (18'8") 70 mm (31") 360 mm (12'0") Triple Grouser Shoes R2.B mm (7'") 440 mm (14'7") 100 mm/60 in 3000 mm/120 in 400 mm/180 in 6000 mm/240 in 700 mm/300 in mm in 700 mm 300 in 6000 mm 240 in 400 mm 180 in 3000 mm 120 in 100 mm 60 in 0 mm 0 in 100 mm 60 in 3000 mm 120 in 400 mm 180 in *40 *40 *40 *40 *11,0 11,00 * * *13,000 11,600 *12,30 8,200 * * *18,70 16,80 *14,00 11,100 12,300 8,000 * * *22,800 1,800 16,800 10,600 12,00 7,70 *6600 *6600 * *1,200 *1,200 *2,00 1,200 16,400 10,20 11,80 7,600 *7100 *7100 * * * *1,800 *1,800 *2,00 *2,00 *2,30 1,000 16,200 10,00 11,800 7,0 * * * * *27,10 *27,10 *33,600 2,00 *23,700 1,10 16,300 10,10 * * * *26,0 *26,0 *1,000 1,600 *4300 *,0 *4000 *8,800 *300 *8,600 *4000 *8,800 *420 *,30 *4700 *10, , ,60 *670 *14,80 *4300 *,0 *4000 *8, , , , , , , , ISO 1067 *Indicates that the load is limited by hydraulic lifting capacity rather than tipping load. The above loads are in compliance with hydraulic excavator lift capacity standard ISO 1067:2007. They do not exceed 87% of hydraulic lifting capacity or 7% of tipping load. Weight of all lifting accessories must be deducted from the above lifting capacities. Lifting capacities are based on the machine standing on a firm, uniform supporting surface. The use of a work tool attachment point to handle/lift objects, could affect the machine lift performance. Lift capacity stays with ±% for all available track shoes. Always refer to the appropriate Operation and Maintenance Manual for specific product information. 7

8 Super Long Reach Boom Lift Capacities Counterweight: 4.7 mt (10,400 ) without Bucket 6.28 m (20'7") 8.8 m (2'0") 70 mm (31") 360 mm (12'0") Triple Grouser Shoes Super Long Reach 2380 mm (7'") 440 mm (14'7") 100 mm/60 in 3000 mm/120 in 400 mm/180 in 6000 mm/240 in 700 mm/300 in mm 480 in mm 420 in 000 mm 360 in 700 mm 300 in 6000 mm 240 in 400 mm 180 in 3000 mm 120 in 100 mm 60 in 0 mm 0 in 100 mm 60 in 3000 mm 120 in 400 mm 180 in 6000 mm 240 in 700 mm 300 in 000 mm 360 in *4700 *4700 *670 *670 *000 *000 * *11,80 *11,80 *14,40 *14,40 *10,70 *10,70 *8,800 7,0 * *00 40 * *16,000 14,200 *12,70,800 *10,00 7,20 *2000 *2000 *460 *460 * *4,0 *4,0 *10,700 *10,700 *14,30 8,80 11,000 6,600 *2100 *2100 *2700 *2700 *460 * *4,600 *4,600 *6,100 *6,100 *10,00 *10,00 14,400 8,20 10,0 6,10 *280 *280 *30 *30 *200 * *6,30 *6,30 *7,00 *7,00 *11,70 *11,70 14,100 7,0 10,20,00 *360 *360 *4400 *4400 * *8,10 *8,10 *,00 *,00 *13,700 11,0 14,000 7,80 10,100,800 *40 *40 *400 *400 * *10,10 *10,10 *12,10 *12,10 *16,30 12,200 14,100 7,0 10,10,80 *00 *00 *6600 *6600 * * *12,20 *12,20 *14,800 *14,800 *17,800 12,600 *13,80 8,200 10,30 6,000 *70 *70 * * * *18,000 *18,000 *14,0 13,20 *11,800 8,60 *,00 6,300 mm in *120 * *2,800 *2, *1200 * *2,600 *2, *110 * *2,40 *2,40 00 *1100 * *2,400 *2, *1100 * *2,400 *2,400 0 *1100 * *2,400 *2, *110 * *2,00 *2,00 80 * *2,600 2,00 80 * *2,70 2,40 70 * *3,000 2,00 60 * *3,300 2,600 0 * *3,70 2, * *4,40 3, * *,60 3, * *6,800 4, ISO 1067 *Indicates that the load is limited by hydraulic lifting capacity rather than tipping load. The above loads are in compliance with hydraulic excavator lift capacity standard ISO 1067:2007. They do not exceed 87% of hydraulic lifting capacity or 7% of tipping load. Weight of all lifting accessories must be deducted from the above lifting capacities. Lifting capacities are based on the machine standing on a firm, uniform supporting surface. The use of a work tool attachment point to handle/lift objects, could affect the machine lift performance. Lift capacity stays with ±% for all available track shoes. Always refer to the appropriate Operation and Maintenance Manual for specific product information. (continued on next page) 8

9 Super Long Reach Boom Lift Capacities Counterweight: 4.7 mt (10,400 ) without Bucket (continued) 6.28 m (20'7") 8.8 m (2'0") 70 mm (31") 360 mm (12'0") Triple Grouser Shoes Super Long Reach 2380 mm (7'") 440 mm (14'7") 000 mm/360 in mm/420 in mm/480 in mm/40 in mm in mm 480 in mm 420 in 000 mm 360 in 700 mm 300 in 6000 mm 240 in 400 mm 180 in 3000 mm 120 in 100 mm 60 in 0 mm 0 in 100 mm 60 in 3000 mm 120 in 400 mm 180 in 6000 mm 240 in 700 mm 300 in 000 mm 360 in *230 *230 *4,700 *4,700 *240 *240 * *,40 *,40 *3,60 *3,60 *20 20 * *,0,40 *,400 4,10 * * * *,00,20 *,700 4,00 *3,20 3,100 * * * *6,80 6,00 *6,300,000 *,0 3,00 *4,600 3,00 * * *7,600 6,00 *6,80 4,700 6,000 3,700 4,00 2,0 * *8,400,0 7,10 4,400,800 3,00 4,800 2, ,0,10 6,80 4,100,600 3,300 4,60 2, ,200 4,80 6,600 3,00,40 3,200 4,600 2, ,0 4,60 6,40 3,70,30 3,100 *3,60 2, ,80 4,0 6,30 3,700,30 3, ,00 4,0 6,400 3,700 *,10 3, ,00 4,700 6,600 3,80 * *7,00,000 *120 *2,800 *1200 *2,600 *110 *2,40 *1100 *2,400 *1100 *2,400 *1100 *2,400 *110 *2,00 *1200 *2,600 *120 *2,70 *130 *3,000 *100 *3,300 *1700 *3,70 *2000 *4,40 *200 *,60 *3100 *6,800 *120 *2,800 *1200 *2,600 *110 *2,40 *1100 *2,400 *1100 *2,400 *1100 *2,400 *110 *2, , , , , , , , , ISO 1067 *Indicates that the load is limited by hydraulic lifting capacity rather than tipping load. The above loads are in compliance with hydraulic excavator lift capacity standard ISO 1067:2007. They do not exceed 87% of hydraulic lifting capacity or 7% of tipping load. Weight of all lifting accessories must be deducted from the above lifting capacities. Lifting capacities are based on the machine standing on a firm, uniform supporting surface. The use of a work tool attachment point to handle/lift objects, could affect the machine lift performance. Lift capacity stays with ±% for all available track shoes. Always refer to the appropriate Operation and Maintenance Manual for specific product information.

10 Bucket Specifications and Compatibility 320 Pin-On (No Quick Coupler) General Duty Capacity (GDC) General Duty Capacity (GDC) Wide Tip Heavy Duty (HD) Heavy Duty Power (HDP) Severe Duty (SD) Severe Duty Power (SDP) Mud/Cleanup (M/CU) Ditch Cleaning (DC) Ditch Cleaning Tilt (DCT) General Duty (GD) Ditch Cleaning (DC) Long Reach Linkage Width Capacity Weight Fill 4.2 mt (,300 ) Counterweight Reach Boom 4.7 mt (10,400 ) Counterweight SLR Boom mm in m 3 yd 3 % R2. ('6") 6.28A (20'7") B , B , B , B , B , B , X B , B , B , B , B , B , X B , B , B , B , B , B , X B , B , 100 B , X B ,30 0 B ,768 0 B , 0 B ,12 0 B ,320 0 B ,001 0 B , B , B , B , B , B , B , Maximum load with pin-on (payload + bucket) ,636 1,764 The above loads are in compliance with hydraulic excavator standard EN474, they do not exceed Maximum Material Density: 87% of hydraulic lifting capacity or 7% of tipping capacity with front linkage fully extended at 2100 /m 3 (3,00 /yd 3 ) ground line with bucket curled /m 3 (3,000 /yd 3 ) Capacity based on ISO /m 3 (2,00 /yd 3 ) Bucket weight with General Duty tips /m 3 (2,000 /yd 3 ) 00 /m 3 (1,00 /yd 3 ) X Not Recommended Caterpillar recommends using appropriate work tools to maximize the value customers receive from our products. Use of work tools, including buckets, which are outside of Caterpillar s recommendations or specifications for weight, dimensions, flows, pressures, etc. may result in less-than-optimal performance, including but not limited to reductions in production, stability, reliability, and component durability. Improper use of a work tool resulting in sweeping, prying, twisting and/or catching of heavy loads will reduce the life of the boom and stick. 10

11 Bucket Specifications and Compatibility 320 Long With Cat Pin Grabber Coupler General Duty Capacity (GDC) General Duty Capacity (GDC) Wide Tip Heavy Duty (HD) Heavy Duty Power (HDP) Heavy Duty Pin Grabber Performance (HD PGP) Severe Duty (SD) Severe Duty Power (SDP) Mud/Cleanup (M/CU) Ditch Cleaning (DC) Ditch Cleaning Tilt (DCT) Linkage Width Capacity Weight Fill 4.2 mt (,300 ) Counterweight Reach Boom 4.7 mt (10,400 ) Counterweight SLR Boom mm in m 3 yd 3 % R2. ('6") 6.28A (20'7") B , B , B , B , B , B , B , B , B , B , B , B , B , B , B , B , B , B , B , B , 100 B , B , B , B , B , B , B , B ,30 0 B ,768 0 B , 0 B ,12 0 B B B B B B , , , , , , B , B , B , Maximum load with coupler (payload + bucket) , The above loads are in compliance with hydraulic excavator standard EN474, they do not exceed Maximum Material Density: 87% of hydraulic lifting capacity or 7% of tipping capacity with front linkage fully extended at 2100 /m 3 (3,00 /yd 3 ) ground line with bucket curled /m 3 (3,000 /yd 3 ) Capacity based on ISO /m 3 (2,00 /yd 3 ) Bucket weight with General Duty tips /m 3 (2,000 /yd 3 ) 00 /m 3 (1,00 /yd 3 ) Caterpillar recommends using appropriate work tools to maximize the value customers receive from our products. Use of work tools, including buckets, which are outside of Caterpillar s recommendations or specifications for weight, dimensions, flows, pressures, etc. may result in less-than-optimal performance, including but not limited to reductions in production, stability, reliability, and component durability. Improper use of a work tool resulting in sweeping, prying, twisting and/or catching of heavy loads will reduce the life of the boom and stick. 11

12 Work Tool Offering Guide* Boom Type Stick Size Reach Boom R2. ('6") Hydraulic Hammer B20 0% C H11Es H120Es 0% C H130Es 0% P Multi-Processor MP318 CC Jaw MP318 D Jaw MP318 P Jaw ^ MP318 U Jaw MP318 S Jaw Pulverizer P21 Demolition and Sorting Grapple G31B-D/R ^ G320B-D/R **, ## G31B-WH ^ Scrap and Demolition Shear S320B S32B # S200 # Compactor (Vibratory Plate) CVP110 Orange Peel Grapple Trash Grapple These work tools are available for the 320. Thumbs Consult your Cat dealer for proper match. Rakes Pin Grabber Coupler Cat PG *Offerings not available in all areas. Matches are dependent on excavator configurations. Consult your Cat dealer to determine what is offered in your area and for proper work tool match. Match ** Match; Pin-On only # Match; Boom Mount ## Work over the front only ^ Work over the front only with Cat PG (match; Pin-On and Cat PG) 0% P Allowed usage with Pin-On and Coupler on machine less than 0% 0% C Allowed usage with Coupler on machine less than 0% Demolition and Sorting Grapple: D Demolition shells, R Recycling shells, WH Waste Handling shells 12

13 320 Standard and Optional Equipment Standard and Optional Equipment Standard and optional equipment may vary. Consult your Cat dealer for details. Standard Optional ENGINE Cat C4.4 ACERT Twin Turbo Tier 4 Final diesel engine Three selectable power modes One-touch low idle with automatic engine speed control Automatic engine idle shutdown Work up to 3000 m (,842. ft) above sea level without engine power de-rating 46 C (11 F) high-ambient cooling capacity 2 C (12 F) high-ambient cooling capacity Cold starting capability for 32 C ( 2 F) Double element air filter with integrated precleaner Electric fuel priming pump Reversible electric cooling fans Biodiesel capability up to B20 HYDRAULIC SYSTEM Boom and stick regeneration circuits Electronic main control valve Auto hydraulic oil warm up Automatic two-speed travel Boom and stick drift reduction valve Element type main hydraulic filter Slider joysticks Tandem type electronic main pump Hammer return filter circuit Combined flow/high pressure auxiliary circuit Medium pressure auxiliary circuit Quick coupler circuit for Cat Pin Grabber Fine swing control Standard Optional UNDERCARRIAGE AND STRUCTURES Tie-down points on base frame (ISO 1818 compliant) Center track guiding guard Standard bottom guards Standard swivel guard Standard travel motor guards Grease lubricated track links 4200 (,300 ) counterweight 4700 (10,400 ) counterweight for Super Long Reach Semi-HD swing frame for C4.4 ACERT Standard swing bearing Base frame with HD track rollers and standard carrier rollers Final drive with standard travel motor BOOM, STICKS AND LINKAGES 70 mm (31 in) triple grouser track shoes.7 m (18'8") Reach boom 2. m ('6") stick Super Long Reach 8.8 m (2'0") boom Super Long Reach 6.28 m (20'7") stick Bucket linkage, B1-family without lifting eye, Cat GRADE Bucket linkage, A-family without lifting eye, SLR (continued on next page) 13

14 320 Standard and Optional Equipment Standard and Optional Equipment (continued) Standard and optional equipment may vary. Consult your Cat dealer for details. ELECTRICAL SYSTEM Machine electronic control module ( 2) 1,000 CCA maintenance-free batteries ( 2) Centralized electrical disconnect switch Programmable time-delay LED working lights LED chassis light, LH and RH boom lights for Reach and SLR, cab lights CAT CONNECT TECHNOLOGY Cat Product Link Cat GRADE with 2D (not available on SLR) Cat GRADE with Advanced 2D (not available on SLR) Cat GRADE with 3D (not available on SLR) Cat Assist: Boom Assist Bucket Assist Swing Assist Grade Assist Cat Payload: Payload Information Static Weigh Auto Calibration Standard Optional Standard Optional SERVICE AND MAINTENANCE Sampling ports for Scheduled Oil Sampling (S O S SM ) Preventative Maintenance ready (QuickEvac ) Grouped location for engine oil and fuel filters Ground level second dipstick for engine oil Remote flash SAFETY AND SECURITY Rearview camera and side RH mirror 360 visibility Neutral lever (lock out) for all controls Anti-skid plate and countersunk bolts on service platform Ground-level accessible secondary engine shutoff switch in cab Radiator screen Bluetooth receiver RH handrail and hand hold (ISO 2867 compliant) Travel alarm 320 Attachments Dealer Installed Kit and Attachments Attachments may vary. Consult your Cat dealer for details. CAB SAFETY AND SECURITY GUARDS Radial lower wiper for 70/30 with washer Bluetooth key fob Standard swivel guard LH/RH electrical pedal for tool control Side rubber bumper Dual exit rear window kit ELECTRICAL FOGS (not compatible with cab light cover, Rain protector plus cab light cover Jump start wiring rain protector) Seat belt, retractable (7 mm/3 in width) LED premium lighting package Mesh guard full front (not compatible with cab light cover, rain protector) Mesh guard lower half front Full protecting vandalism guard 14

15 320 Cab Options Cab Options ROPS, standard sound suppression High-resolution 203 mm (8 in) LCD touch screen monitor High-resolution 203 mm (8 in) LCD touch screen monitor + additional monitor (only for use with Cat GRADE with Advanced 2D or Cat GRADE with 3D) High-resolution 24 mm (10 in) LCD touch screen monitor (only for use with 360 visibility) High-resolution 24 mm (10 in) LCD touch screen monitor + additional monitor (only for use with 360 visibility and Cat GRADE with Advanced 2D or Cat GRADE with 3D) Automatic bi-level air conditioner Jog dial and shortcut keys for monitor control Keyless push-to-start engine control Height-adjustable console, infinite with no tool Air-adjustable seat suspension 1 mm (2 in) seat belt Seat heater Tilt-up left-side console Bluetooth integrated radio with USB ports 2 12V DC outlets Document storage Cup and bottle holders Two-piece front window, openable Upper radial wiper with 70/30 with washer Polycarbonate skylight hatch, openable LED dome and lower interior lights Roller front sunscreen Roller rear sunscreen Rain protector and cab light covers (only for use with 360 visibility) Beacon ready Washable floor mat Storage tray in pump compartment Straight travel pedal Deluxe Standard Optional 1

16 For more complete information on Cat products, dealer services, and industry solutions, visit us on the web at Caterpillar All rights reserved AEXQ2161 ( ) Build Number: 07A (North America) Materials and specifications are subject to change without notice. Featured machines in photos may include additional equipment. See your Cat dealer for available options. CAT, CATERPILLAR, SAFETY.CAT.COM, their respective logos, Caterpillar Yellow and the Power Edge trade dress, as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.