Simulation and Optimization of MPV Suspension System Based on ADAMS

Size: px
Start display at page:

Download "Simulation and Optimization of MPV Suspension System Based on ADAMS"

Transcription

1 11 th World Congress on Structural and Multidisciplinary Optimisation 07 th -12 th, June 2015, Sydney Australia Simulation and Optimization of MPV Suspension System Based on ADAMS Dongchen Qin 1, Junjie Yang 1, Qiang Zhu 1, Peng Du 1 1 Zhengzhou University, Zhengzhou, China, dcqin@zzu.edu.cn 1. Abstract The suspension system is one of the key parts in vehicles, which can directly influence such performances as the steering stability and the ride comfort. The multi-body dynamics model of multi-purpose vehicles (MPV) front suspension is built with ADAMS/VIEW, and the location parameters of the front wheel are simulated. In order to improve the kinematics performance and steering stability, the sensitivity analysis and optimization design for the front suspension are carried out. The results can provide some guide and reference for the R&D of the MPV. 2. Keywords: Macpherson Suspension, Multi-body Dynamics, ADAMS/VIEW, Optimization Design 3. Introduction The most important assembly designs of the automobile are suspension, engine and transmission. The design of suspension system influences a variety of performances. Vehicle suspension is the important structure linked to the frame and tires. In the paper, the front McPherson independent suspension of a MPV was analysed for improving its performance. And the virtual prototype model for this suspension, the dynamic simulation models, parametric processing and the optimization of front independent suspension are established. The suspension set up and perfect virtual prototyping model, will upgrade this MPV s independent suspension design level, and also provide foundations for a new suspension design of similar models. 4. Multi-body dynamics model of MPV suspension Utility of vehicle suspension system is to pass all forces and moments between the wheel and the frame (or body), and to ease the impact load coming from rough road, which can reduce the vibration of bearing system caused by the impact load. And also the suspension system can reduce the interior nose of vehicle and increase occupant comfortable, which can ensure the vehicle s ride comfort. As an important force transmission member connected the frame (or body) and the axle (or wheel), the vehicle suspension system is a key component to ensure the vehicle safety. 4.1 Composition and characteristic of McPherson independent suspension The front suspension of this MPV uses McPherson independent suspension. Figure1 shows a typical configuration. 1-body;2-coil spring;3-shock absorber upper body;4-knuckle assembly;5-tie rod;6-steering rack;7-under the arm8-wheel assembly Figure1: McPherson suspension structure diagram 4.2 Coordinates of the key points of the model The spatial coordinates and parameters of the key points are important for establishing suspension model, which is the most important task before executing the kinematic simulation in ADAMS. This article uses the coordinate mapping instrument to get the space parameters of the left suspension under no-load conditions. The table1 shows the front suspension positional parameters. 1

2 Table1: The positional parameters of front McPherson independent suspension Parameter name Value of design The kingpin The caster The toe The camber of The volume of inclination angle angle angle front wheel wheel spin(mm) The simulation model A drive was added on the test platform after building the model of the guiding mechanism. The figure2 shows the model and the test platform. 1-shock absorber; 2-coil spring; 3-wheel; 4-lower control arm; 5-tie rod; 6-knuckle assembly; 7-body Figure2: The simulation model of the front McPherson suspension 5 The performance simulation and analysis of MPV suspension The common analysis method of the kinematic characteristics of the suspension is that wheels beat with a wheel on one side or both sides up and down along the vertical directional, variation of wheel position parameters is calculated and analyzed. Based on full load, the range of the run out is at popular -50~+50mm for a vehicle of this study, while the characteristics of the toe angle of wheel, camber angle and wheel hop gauge changing are calculated. The range of the front toe angle is ~0.80 in figure3, and which meets the requirements, that is, the change in angle of less than ±1. The jump has a positive camber angle, varied from ~+2.74 in figure4. The range of variation is too large, and the straight running stability will deteriorate automobiles. The range of the caster angle is 2.77 ~3.37 in figure5. The amount of change is small, which meets the design requirements, and is favor of the vehicle load handing and stability. The range of kingpin inclination angle is 7.47 ~11.16 in the figure6. The amount of change is too large and is not conducive to vehicle handing and stability. The figure7 shows that the change range of the wheel tread is between mm/50mm and mm/50mm, which it s an important performance for a worn tirer. The simulation model was builded in ADAMS/VIEW, and combined the date of the front McPherson suspension, and elected the method of left wheel jumping, and executed the kinematic simulation of the McPherson suspension. The curve of front toe angle, the camber angle, the kingpin inclination angle, the caster angle and wheel tread could be got. And the front toe angle of front wheel is too large, and the change range of the wheel tread is beyond the common. So these will increased tire wear. 2

3 6. Suspension performance sensitivity analysis The performance of the vehicle front suspension for sensitivity analysis can get the properties of all the suspension components and installation location of vehicle suspension and provide a reference to the design of suspension. The model of suspension is built and the design parameters of suspension and the sensitivity of the performance of the vehicle are calculated with using the Insight module and CAR module in ADAMS. And the sensitivity of suspension performance is analyzed in VIEW. In this article, the ADAMS/VIEW is selected for analyzing the sensitivity of suspension performance. The main impact factors of operational stability can be found from this model. 6.1 Design variables According to the front suspension structure and the position parameters of the front wheel, the length and position angle in space of links EG, EF, CB are elected as design variables sensitivity analysis. The table2 shows the symbol and the significance of 9 variables. Table2: Definition of the design variable Number Design Means Code in ADAMS 1 x1 The length of EG DV_1 2 x2 The angle between the EG and xy plane DV_2 3 x3 The angle between EG projection in the xy plane and x-axis DV_3 4 x4 The length of EF DV_4 5 x5 The angle between EF and xy plane DV_5 6 x6 The angle between EF projection in the xy plane and x-axis DV_6 7 x7 The length of CB DV_7 8 x8 The complement of the angle between CB and xy plane DV_8 9 x9 The complement of the angle between CB projection in the xy plane and the y-axis DV_9 6.2 Sensitivity analysis This paper focuses on the front wheel alignment toe angle, the camber angle, and the volume of tire lateral slip, which was recorded with the initial values of the sensitivity.the conclusion can be got from the figures 8 to 16. 3

4 (1) On a larger camber factors followed as: angle between the link EF and xy plane(x5), and complementary angle of xy plane with connecting rod CB(x8), angle between the connecting rod EG and xy plane(x2), other factors less affected. (2) The front wheel lateral amount greater factor in turn: the angle between the link rod CB and xy plane(x8), the link EF and xy plane angle(x5), EG and xy plane angle(x2), other factors less affected. 7. The optimization of the MPV suspension The smallest amount of sideslip change is made in order to optimize the range direction. The simulation mode is executed in the ADAMS/View, with adjustments to the hard point coordinates of air spring independent suspension, and then the best hard point coordinate as the last optimization design point. Such parameters as angle between EF and xy plane, angle between EF projection in the xy plane and the x-axis, angle between complementary angle of CB and the xy plane, and angle between complementary angle of CB projection and y-axis are optimized, and the curve of experimental and results of optimization are obtained. 7.1 The bjective function In order to reduce tire wear, we select the front wheel lateral slip amount as the optimization of the objective function. Through optimizing such parameters as angle between EF and xy plane, angle between CB and xy plane, angle between complementary angle of CB projection and xy plane, angle between complementary angle of CB projection in the xy plane and y-axis, the value of the minimum lateral slip of the wheels is obtained. 7.2 The optimization model The objective function in the optimization and design variables are set in the window of ADAMS. The design variables are DV_5, DV_6, DV_8 and DV_9. And the optimization goal is that the objective function takes the minimum value. For optimization of the front independent suspension performance, the sequential quadratic programming method of ADAMS/VIEW is used. Table3 shows the optimization result. 7.3 The optimization results Table3 shows the different values of DV_5, DV_6, DV_8, DV_9 for the twice optimization iteration. Table3: The result of suspension optimization Iterations Objective function(mm) x5(deg) x6(deg) x8(mm) x9(deg) Suspension characteristic curves comparing The simulation curves of the optimized models are shown as following. The blue curve represents the simulation after optimization, and the red curve represents the simulation before optimization. Figures17~21 show the comparison results of the alignment parameters. The range of variation optimized camber is ~1.769 from the figure17. The changes of the toe angle of the front wheel are not large as that can be seen from figure18. The optimization result of the toe angle is acceptable when the wheels balanced and within the design limits. Figure19 shows that the kingpin inclination optimized range is ~3.412, with expanding the scope of change little compared with optimization before. The change 4

5 range of the kingpin inclination angle is ~ from the figure20. The volume of wheel lateral slip range is ~0.79 from the figure21.the curve of optimization is better than that of before. The parameters of the internal connect position of the steering tie rod, the external position of the lower support arm change very large for this suspension model. By adjusting the parameters a greater response to the result of each change can be obtained. The camber angle of front wheel, the caster angle, and the volume of lateral slip will become better through the comparison of simulation curves, while the change of the toe angle is not obvious. We can get a new suspension layout scheme by optimizing design. The simulation results of the suspension performance are more reasonable. And the maneuverability and stability of the vehicle can be greatly improved. 8. Conclusions In this paper, taking the front McPherson independent suspension of a MPV as the object, the structure of the suspension is analyzed briefly, and the dynamics model of the suspension combined with multi-body system dynamics theory is established in ADAMS/VIEW. And the curves of the vehicle performance are obtained, which include the toe angle, the camber angle, the kingpin inclination angle, the caster angle and the volume of lateral slip of the front wheel. On the basis of the suspension performance simulation, by using ADAMS/VIEW to set the variables of the suspension, the influence of the camber angle, the kingpin angle and the volume of lateral slip can be analyzed. Those results can provide data for improving the design of MPV suspension. The coordinates of two inner points and the tie rod inner point are changed through using optimized design parameters. The layout scheme is optimized and executed. Comparing with the previous design, the optimized simulation results are more reasonable. 9. References [1] Jiang Liu, Based on virtual prototype technology suspension system performance analysis and optimization, Shanghai: Shanghai Jiao Tong University,2007. [2] M. H. Kim, J. H. Oh, J. H. Lee, M. C. Jeon, Development of rollover criteria based on simple physical model of rollover event. International Journal of Automotive Technology, (1):51~59,2006. [3] N. Orlandea, M.A. Chace, Simulation of vehicle suspension with ADAMS computer program, SAE Technical Paper [4] Wenjie Yi, Vehicle Dynamics suspension kinematics analysis and parameter optimization, Beijing :Beijing Institute of Technology,2003. [5] Shaoqi Cen, Xiao Pan, Dongchen Qin, Application research on vehicle handling stability dynamics simulating using ADAMS, Journal of Zhengzhou University(Engineering Science),27(3):55~58,2006. [5] Peng Ji, Zhenjun Sun, Guohua Cui, Application of ADAMS in vehicle handling stability evaluation, Agricultural Equipment & Vehicle Engineering,(5):32~ [6] Dongchen Qin, Modeling,simulation and optimization oriented to handling and stability of sport utility vehicle,wuhan: Huazhong University of Science and Technology,2007. [7] Aihua Feng, Virtual Prototype technology-based vehicle ride comfort analysis and driving simulation, Changchun:Jilin University,2007. [8] Hailin Sun, The kinematics/elastokinematics simulation and analysis of the multi-link suspension system of the car, Changchun:Jilin University,

Kinematic Analysis of Roll Motion for a Strut/SLA Suspension System Yung Chang Chen, Po Yi Tsai, I An Lai

Kinematic Analysis of Roll Motion for a Strut/SLA Suspension System Yung Chang Chen, Po Yi Tsai, I An Lai Kinematic Analysis of Roll Motion for a Strut/SLA Suspension System Yung Chang Chen, Po Yi Tsai, I An Lai Abstract The roll center is one of the key parameters for designing a suspension. Several driving

More information

Modeling and Simulation of Linear Two - DOF Vehicle Handling Stability

Modeling and Simulation of Linear Two - DOF Vehicle Handling Stability Modeling and Simulation of Linear Two - DOF Vehicle Handling Stability Pei-Cheng SHI a, Qi ZHAO and Shan-Shan PENG Anhui Polytechnic University, Anhui Engineering Technology Research Center of Automotive

More information

KINEMATICAL SUSPENSION OPTIMIZATION USING DESIGN OF EXPERIMENT METHOD

KINEMATICAL SUSPENSION OPTIMIZATION USING DESIGN OF EXPERIMENT METHOD Jurnal Mekanikal June 2014, No 37, 16-25 KINEMATICAL SUSPENSION OPTIMIZATION USING DESIGN OF EXPERIMENT METHOD Mohd Awaluddin A Rahman and Afandi Dzakaria Faculty of Mechanical Engineering, Universiti

More information

Structure Parameters Optimization Analysis of Hydraulic Hammer System *

Structure Parameters Optimization Analysis of Hydraulic Hammer System * Modern Mechanical Engineering, 2012, 2, 137-142 http://dx.doi.org/10.4236/mme.2012.24018 Published Online November 2012 (http://www.scirp.org/journal/mme) Structure Parameters Optimization Analysis of

More information

Advances in Engineering Research (AER), volume 102 Second International Conference on Mechanics, Materials and Structural Engineering (ICMMSE 2017)

Advances in Engineering Research (AER), volume 102 Second International Conference on Mechanics, Materials and Structural Engineering (ICMMSE 2017) Advances in Engineering Research (AER), volume 102 Second International Conference on Mechanics, Materials and Structural Engineering (ICMMSE 2017) Vibration Characteristic Analysis of the Cross-type Joint

More information

A Certain Type of Wheeled Self-propelled Gun Independent Suspension Stress Analysis. Liu Xinyuna, Ma Jishengb

A Certain Type of Wheeled Self-propelled Gun Independent Suspension Stress Analysis. Liu Xinyuna, Ma Jishengb 6th International Conference on Machinery, Materials, Environment, Biotechnology and Computer (MMEBC 216) A Certain Type of Wheeled Self-propelled Gun Independent Suspension Stress Analysis Liu Xinyuna,

More information

Design and optimization of Double wishbone suspension system for ATVs

Design and optimization of Double wishbone suspension system for ATVs Design and optimization of Double wishbone suspension system for ATVs Shantanu Garud 1, Pritam Nagare 2, Rohit Kusalkar 3, Vijaysingh Gadhave 4, Ajinkya Sawant 5 1,2,3,4Dept of Mechanical Engineering,

More information

2. MEASURE VEHICLE HEIGHT. (b) Measure the vehicle height. Measurement points: C: Ground clearance of front wheel center

2. MEASURE VEHICLE HEIGHT. (b) Measure the vehicle height. Measurement points: C: Ground clearance of front wheel center ADJUSTMENT If the wheel alignment has been adjusted, and if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order

More information

Development of analytical process to reduce side load in strut-type suspension

Development of analytical process to reduce side load in strut-type suspension Journal of Mechanical Science and Technology 24 (21) 351~356 www.springerlink.com/content/1738-494x DOI 1.7/s1226-9-113-z Development of analytical process to reduce side load in strut-type suspension

More information

Design of Suspension and Steering system for an All-Terrain Vehicle and their Interdependence

Design of Suspension and Steering system for an All-Terrain Vehicle and their Interdependence Design of Suspension and Steering system for an All-Terrain Vehicle and their Interdependence Saurabh Wanganekar 1, Chinmay Sapkale 2, Priyanka Chothe 3, Reshma Rohakale 4,Samadhan Bhosale 5 1 Student,Department

More information

The Application of Simulink for Vibration Simulation of Suspension Dual-mass System

The Application of Simulink for Vibration Simulation of Suspension Dual-mass System Sensors & Transducers 204 by IFSA Publishing, S. L. http://www.sensorsportal.com The Application of Simulink for Vibration Simulation of Suspension Dual-mass System Gao Fei, 2 Qu Xiao Fei, 2 Zheng Pei

More information

Torque steer effects resulting from tyre aligning torque Effect of kinematics and elastokinematics

Torque steer effects resulting from tyre aligning torque Effect of kinematics and elastokinematics P refa c e Tyres of suspension and drive 1.1 General characteristics of wheel suspensions 1.2 Independent wheel suspensions- general 1.2.1 Requirements 1.2.2 Double wishbone suspensions 1.2.3 McPherson

More information

Simulation Analysis of Automobile Air Suspension Dynamics based on ADAMS Shuai Li 1, Zhongliang Meng 1, Weikai Jiang 2

Simulation Analysis of Automobile Air Suspension Dynamics based on ADAMS Shuai Li 1, Zhongliang Meng 1, Weikai Jiang 2 International Conference on Intelligent Systems Research and Mechatronics Engineering (ISRME 205) Simulation Analysis of Automobile Air Suspension Dynamics based on ADAMS Shuai Li, Zhongliang Meng, Weikai

More information

Hard Points Optimization Design of Air Spring Suspension Based on Sensitivity. Analysis

Hard Points Optimization Design of Air Spring Suspension Based on Sensitivity. Analysis GUIBIN SUN et al: HARD POINTS OPTIMIZATION DESIGN OF AIR SPRING SUSPENSION BASED ON.. Hard Points Optimization Design of Air Spring Suspension Based on Sensitivity Analysis Guibin SUN, Youming TANG *,

More information

Identification of A Vehicle Pull Mechanism

Identification of A Vehicle Pull Mechanism Seoul 2000 FISITA World Automotive Congress June 12-15, 2000, Seoul, Korea F2000G353 Identification of A Vehicle Pull Mechanism Sang-Hyun Oh*, Young-Hee Cho, Gwanghun Gim Vehicle Dynamics Research Team,

More information

MODELS FOR THE DYNAMIC ANALYSIS OF THE SUSPENSION SYSTEM OF THE VEHICLES REAR AXLE

MODELS FOR THE DYNAMIC ANALYSIS OF THE SUSPENSION SYSTEM OF THE VEHICLES REAR AXLE MODELS FOR THE DYNAMIC ANALYSIS OF THE SUSPENSION SYSTEM OF THE VEHICLES REAR AXLE Alexandru Cătălin Transilvania University of Braşov, Product Design and Robotics Department, calex@unitbv.ro Keywords:

More information

Dynamic and Decoupling Analysis of the Bogie with Single EMS Modules for Low-speed Maglev Train

Dynamic and Decoupling Analysis of the Bogie with Single EMS Modules for Low-speed Maglev Train , pp.83-88 http://dx.doi.org/10.14257/astl.2016. Dynamic and Decoupling Analysis of the Bogie with Single EMS Modules for Low-speed Maglev Train Yougang Sun* 1, 2, Wanli Li 1, Daofang Chang 2, Yuanyuan

More information

The Assist Curve Design for Electric Power Steering System Qinghe Liu1, a, Weiguang Kong2, b and Tao Li3, c

The Assist Curve Design for Electric Power Steering System Qinghe Liu1, a, Weiguang Kong2, b and Tao Li3, c 2nd International Conference on Advances in Mechanical Engineering and Industrial Informatics (AMEII 26) The Assist Curve Design for Electric Power Steering System Qinghe Liu, a, Weiguang Kong2, b and

More information

Characteristics of wheel-rail vibration of the vertical section in high-speed railways

Characteristics of wheel-rail vibration of the vertical section in high-speed railways Journal of Modern Transportation Volume, Number 1, March 12, Page -15 Journal homepage: jmt.swjtu.edu.cn DOI:.07/BF03325771 Characteristics of wheel-rail vibration of the vertical section in high-speed

More information

Design and Analysis of suspension system components

Design and Analysis of suspension system components Design and Analysis of suspension system components Manohar Gade 1, Rayees Shaikh 2, Deepak Bijamwar 3, Shubham Jambale 4, Vikram Kulkarni 5 1 Student, Department of Mechanical Engineering, D Y Patil college

More information

Dynamic simulation of the motor vehicles using commercial software

Dynamic simulation of the motor vehicles using commercial software Dynamic simulation of the motor vehicles using commercial software Cătălin ALEXANDRU University Transilvania of Braşov, Braşov, 500036, Romania Abstract The increasingly growing demand for more comfortable

More information

International Conference on Advances in Energy and Environmental Science (ICAEES 2015)

International Conference on Advances in Energy and Environmental Science (ICAEES 2015) International Conference on Advances in Energy and Environmental Science (ICAEES 2015) Design and Simulation of EV Charging Device Based on Constant Voltage-Constant Current PFC Double Closed-Loop Controller

More information

Application of Airborne Electro-Optical Platform with Shock Absorbers. Hui YAN, Dong-sheng YANG, Tao YUAN, Xiang BI, and Hong-yuan JIANG*

Application of Airborne Electro-Optical Platform with Shock Absorbers. Hui YAN, Dong-sheng YANG, Tao YUAN, Xiang BI, and Hong-yuan JIANG* 2016 International Conference on Applied Mechanics, Mechanical and Materials Engineering (AMMME 2016) ISBN: 978-1-60595-409-7 Application of Airborne Electro-Optical Platform with Shock Absorbers Hui YAN,

More information

Comparison Of Multibody Dynamic Analysis Of Double Wishbone Suspension Using Simmechanics And FEA Approach

Comparison Of Multibody Dynamic Analysis Of Double Wishbone Suspension Using Simmechanics And FEA Approach International Journal of Research in Engineering and Science (IJRES) ISSN (Online): 232-9364, ISSN (Print): 232-9356 Volume 2 Issue 4 ǁ April. 214 ǁ PP.31-37 Comparison Of Multibody Dynamic Analysis Of

More information

MODELING SUSPENSION DAMPER MODULES USING LS-DYNA

MODELING SUSPENSION DAMPER MODULES USING LS-DYNA MODELING SUSPENSION DAMPER MODULES USING LS-DYNA Jason J. Tao Delphi Automotive Systems Energy & Chassis Systems Division 435 Cincinnati Street Dayton, OH 4548 Telephone: (937) 455-6298 E-mail: Jason.J.Tao@Delphiauto.com

More information

Optimization of Hydraulic Retarder Based on CFD Technology

Optimization of Hydraulic Retarder Based on CFD Technology International Conference on Manufacturing Science and Engineering (ICMSE 2015) Optimization of Hydraulic Retarder Based on CFD Technology Li Hao 1, a *, Ren Xiaohui 1,b 1 College of Vehicle and Energy,

More information

Temperature Field in Torque Converter Clutch

Temperature Field in Torque Converter Clutch 3rd International Conference on Mechanical Engineering and Intelligent Systems (ICMEIS 2015) Temperature Field in Torque Converter Clutch Zhenjie Liu 1, a, Chao Yi 1,b and Ye Wang 1,c 1 The State Key Laboratory

More information

Design, analysis and mounting implementation of lateral leaf spring in double wishbone suspension system

Design, analysis and mounting implementation of lateral leaf spring in double wishbone suspension system Design, analysis and mounting implementation of lateral leaf spring in double wishbone suspension system Rahul D. Sawant 1, Gaurav S. Jape 2, Pratap D. Jambhulkar 3 ABSTRACT Suspension system of an All-TerrainVehicle

More information

College of Mechanical & Power Engineering Of China Three Gorges University, Yichang, Hubei Province, China

College of Mechanical & Power Engineering Of China Three Gorges University, Yichang, Hubei Province, China International Conference on Intelligent Systems Research and Mechatronics Engineering (ISRME 215) Hydraulic Hitch Systems of 9t Tyre Hosting Girder Machine Modeling and Simulation Analysis Based On SIMULINK/ADAMS

More information

Pipeline to Hydraulic Pressure Position-Control System. Performance Research

Pipeline to Hydraulic Pressure Position-Control System. Performance Research International Journal of Research in Engineering and Science (IJRES) ISSN (Online): 2320-9364, ISSN (Print): 2320-9356 Volume 3 Issue 6 ǁ June 2015 ǁ PP.30-35 Pipeline to Hydraulic Pressure Position-Control

More information

Multi-body Dynamical Modeling and Co-simulation of Active front Steering Vehicle

Multi-body Dynamical Modeling and Co-simulation of Active front Steering Vehicle The nd International Conference on Computer Application and System Modeling (01) Multi-body Dynamical Modeling and Co-simulation of Active front Steering Vehicle Feng Ying Zhang Qiao Dept. of Automotive

More information

Parametric Modeling and Finite Element Analysis of the Brake Drum Based on ANSYS APDL

Parametric Modeling and Finite Element Analysis of the Brake Drum Based on ANSYS APDL 2017 3rd International Conference on Green Materials and Environmental Engineering (GMEE 2017) ISBN: 978-1-60595-500-1 Parametric Modeling and Finite Element Analysis of the Brake Drum Based on ANSYS APDL

More information

Vibration Analysis of Gear Transmission System in Electric Vehicle

Vibration Analysis of Gear Transmission System in Electric Vehicle Advanced Materials Research Online: 0-0- ISSN: 66-8985, Vols. 99-00, pp 89-83 doi:0.408/www.scientific.net/amr.99-00.89 0 Trans Tech Publications, Switzerland Vibration Analysis of Gear Transmission System

More information

Optimal Design of a Wheelchair Suspension Based on a Compliant Mechanism

Optimal Design of a Wheelchair Suspension Based on a Compliant Mechanism 11 th World Congress on Structural and Multidisciplinary Optimisation 07 th -12 th, June 2015, Sydney Australia Optimal Design of a Wheelchair Suspension Based on a Compliant Mechanism Masakazu Kobayashi

More information

Collaborative vehicle steering and braking control system research Jiuchao Li, Yu Cui, Guohua Zang

Collaborative vehicle steering and braking control system research Jiuchao Li, Yu Cui, Guohua Zang 4th International Conference on Mechatronics, Materials, Chemistry and Computer Engineering (ICMMCCE 2015) Collaborative vehicle steering and braking control system research Jiuchao Li, Yu Cui, Guohua

More information

Bus Handling Validation and Analysis Using ADAMS/Car

Bus Handling Validation and Analysis Using ADAMS/Car Bus Handling Validation and Analysis Using ADAMS/Car Marcelo Prado, Rodivaldo H. Cunha, Álvaro C. Neto debis humaitá ITServices Ltda. Argemiro Costa Pirelli Pneus S.A. José E. D Elboux DaimlerChrysler

More information

1. SPECIFICATIONS 2. WHEEL ALIGNMENT Front Suspension. (gas type) Rear Suspension. (gas type)

1. SPECIFICATIONS 2. WHEEL ALIGNMENT Front Suspension. (gas type) Rear Suspension. (gas type) 441101 053 1. SPECIFICATIONS Front Suspension Rear Suspension Description Suspension type Spring type Shock absorber type Stabilizer bar type Suspension type Spring type Shock absorber type Stabilizer

More information

Skid against Curb simulation using Abaqus/Explicit

Skid against Curb simulation using Abaqus/Explicit Visit the SIMULIA Resource Center for more customer examples. Skid against Curb simulation using Abaqus/Explicit Dipl.-Ing. A. Lepold (FORD), Dipl.-Ing. T. Kroschwald (TECOSIM) Abstract: Skid a full vehicle

More information

Experimental Investigation of Effects of Shock Absorber Mounting Angle on Damping Characterstics

Experimental Investigation of Effects of Shock Absorber Mounting Angle on Damping Characterstics Experimental Investigation of Effects of Shock Absorber Mounting Angle on Damping Characterstics Tanmay P. Dobhada Tushar S. Dhaspatil Prof. S S Hirmukhe Mauli P. Khapale Abstract: A shock absorber is

More information

System. Hefei University of Technology, China. Hefei University of Technology, China. Hefei University of Technology, China

System. Hefei University of Technology, China. Hefei University of Technology, China. Hefei University of Technology, China Automobile Power-train Coupling Vibration Analysis on Vehicle System Heng DING 1 ; Weihua ZHANG 2 ; Wuwei CHEN 3 ; Peicheng Shi 4 1 Hefei University of Technology, China 2 Hefei University of Technology,

More information

Analysis of Aerodynamic Performance of Tesla Model S by CFD

Analysis of Aerodynamic Performance of Tesla Model S by CFD 3rd Annual International Conference on Electronics, Electrical Engineering and Information Science (EEEIS 2017) Analysis of Aerodynamic Performance of Tesla Model S by CFD Qi-Liang WANG1, Zheng WU2, Xian-Liang

More information

Lateral Stability Analysis of Telehandlers Based on Multibody Dynamics

Lateral Stability Analysis of Telehandlers Based on Multibody Dynamics Lateral Stability Analysis of Telehandlers Based on Multibody Dynamics HAOLIANG GUO, 1, * XIHUI MU, 2 FENGPO DU, 2 KAI LV 1 1 Department of Ammunition Engineering Ordnance Engineering College Shijiazhuang

More information

Camber Angle. Wheel Alignment. Camber Split. Caster Angle. Caster and Ride Height. Toe Angle. AUMT Wheel Alignment

Camber Angle. Wheel Alignment. Camber Split. Caster Angle. Caster and Ride Height. Toe Angle. AUMT Wheel Alignment AUMT 1316 - Wheel Alignment 11/15/11 Camber Angle Wheel Alignment Donald Jones Brookhaven College Camber Split Camber is the amount that the centerline of the wheel tilts away from true vertical when viewed

More information

Technology, Xi an , China

Technology, Xi an , China Applied Mechanics and Materials Vol. 251 (2013) pp 221-225 Online available since 2012/Dec/13 at www.scientific.net (2013) Trans Tech Publications, Switzerland doi:10.4028/www.scientific.net/amm.251.221

More information

SIX-BAR STEERING MECHANISM

SIX-BAR STEERING MECHANISM SIX-BAR STEERING MECHANISM Shrey Lende 1 1 UG Student, Department of Mech, G.H Raisoni College of Engineering, Nagpur, RTMN University ABSTRACT In this paper a steering system is designed for a Low weight

More information

GENERAL INFORMATION. Wheel Alignment Theory & Operation

GENERAL INFORMATION. Wheel Alignment Theory & Operation Fig. 1: Checking Steering Linkage GENERAL INFORMATION Wheel Alignment Theory & Operation ADJUSTMENTS NOTE: This article is intended for general information purposes only. This information may not apply

More information

DESIGN AND ANALYSIS OF PUSH ROD ROCKER ARM SUSPENSION USING MONO SPRING

DESIGN AND ANALYSIS OF PUSH ROD ROCKER ARM SUSPENSION USING MONO SPRING Volume 114 No. 9 2017, 465-475 ISSN: 1311-8080 (printed version); ISSN: 1314-3395 (on-line version) url: http://www.ijpam.eu ijpam.eu DESIGN AND ANALYSIS OF PUSH ROD ROCKER ARM SUSPENSION USING MONO SPRING

More information

Dynamic Behavior Analysis of Hydraulic Power Steering Systems

Dynamic Behavior Analysis of Hydraulic Power Steering Systems Dynamic Behavior Analysis of Hydraulic Power Steering Systems Y. TOKUMOTO * *Research & Development Center, Control Devices Development Department Research regarding dynamic modeling of hydraulic power

More information

Modelling and simulation of full vehicle to study its dynamic behavior

Modelling and simulation of full vehicle to study its dynamic behavior Modelling and simulation of full vehicle to study its dynamic behavior 1 Prof. Sachin Jadhao, 2 Mr. Milind K Patil 1 Assistant Professor, 2 Student of ME (Design) Mechanical Engineering J.S.P.M s Rajarshi

More information

Effect of Tyre Overload and Inflation Pressure on Rolling Loss (resistance) and Fuel Consumption of Automobile Cars

Effect of Tyre Overload and Inflation Pressure on Rolling Loss (resistance) and Fuel Consumption of Automobile Cars ISSN (e): 2250 3005 Vol, 04 Issue, 10 October 2014 International Journal of Computational Engineering Research (IJCER) Effect of Tyre Overload and Inflation Pressure on Rolling Loss (resistance) and Fuel

More information

Kinematics and Force Analysis of Lifting Mechanism of Detachable Container Garbage Truck

Kinematics and Force Analysis of Lifting Mechanism of Detachable Container Garbage Truck Send Orders for Reprints to reprints@benthamscience.net The Open Mechanical Engineering Journal, 014, 8, 19-3 19 Open Access Kinematics and Force Analysis of Lifting Mechanism of Detachable Container Garbage

More information

II YEAR AUTOMOBILE ENGINEERING AT AUTOMOTIVE CHASSIS QUESTION BANK UNIT I - LAYOUT, FRAME, FRONT AXLE AND STEERING SYSTEM

II YEAR AUTOMOBILE ENGINEERING AT AUTOMOTIVE CHASSIS QUESTION BANK UNIT I - LAYOUT, FRAME, FRONT AXLE AND STEERING SYSTEM II YEAR AUTOMOBILE ENGINEERING AT 6402 - AUTOMOTIVE CHASSIS QUESTION BANK UNIT I - LAYOUT, FRAME, FRONT AXLE AND STEERING SYSTEM 1. Write about the requirements of frame and selection of cross section

More information

Why do cars need Alignment

Why do cars need Alignment Why do cars need Alignment The main purpose of wheel alignment is to make the tires roll without Scuffing, slipping, or dragging under all operating conditions. Caster Camber Toe Steering axis inclination

More information

Influence of Parameter Variations on System Identification of Full Car Model

Influence of Parameter Variations on System Identification of Full Car Model Influence of Parameter Variations on System Identification of Full Car Model Fengchun Sun, an Cui Abstract The car model is used extensively in the system identification of a vehicle suspension system

More information

Optimization Design of an Interior Permanent Magnet Motor for Electro Hydraulic Power Steering

Optimization Design of an Interior Permanent Magnet Motor for Electro Hydraulic Power Steering Indian Journal of Science and Technology, Vol 9(14), DOI: 10.17485/ijst/2016/v9i14/91100, April 2016 ISSN (Print) : 0974-6846 ISSN (Online) : 0974-5645 Optimization Design of an Interior Permanent Magnet

More information

FRONT WHEEL ALIGNMENT

FRONT WHEEL ALIGNMENT 2 Front: B A A Rear: C D Front SUENSION FRONT WHEEL ALIGNMENT D F046082E03 B FRONT WHEEL ALIGNMENT ADJUSTMENT 1. INECT TIRE (a) Inspect the tires (see page TW-3). 2. MEASURE VEHICLE HEIGHT Standard vehicle

More information

2nd International Conference on Electronic & Mechanical Engineering and Information Technology (EMEIT-2012)

2nd International Conference on Electronic & Mechanical Engineering and Information Technology (EMEIT-2012) Analysis and Control of Shift Process for AMT without Synchronizer in Battery Electric Bus Sun Shaohua 1,a, LEI Yulong 1,b, Yang Cheng 1,c, Wen Jietao 1,d 1 State Key Laboratory of automotive simulation

More information

Study on Tractor Semi-Trailer Roll Stability Control

Study on Tractor Semi-Trailer Roll Stability Control Send Orders for Reprints to reprints@benthamscience.net 238 The Open Mechanical Engineering Journal, 214, 8, 238-242 Study on Tractor Semi-Trailer Roll Stability Control Shuwen Zhou *,1 and Siqi Zhang

More information

Designing and Hard Point Optimization of Suspension System of a Three-Wheel Hybrid Vehicle

Designing and Hard Point Optimization of Suspension System of a Three-Wheel Hybrid Vehicle ISSN (O): 2393-8609 International Journal of Aerospace and Mechanical Engineering Designing and Hard Point Optimization of Suspension System of a Three-Wheel Hybrid Vehicle Gomish Chawla B.Tech Automotive

More information

Development of Fuel Injection System for Non-Road Single-Cylinder Diesel Engine

Development of Fuel Injection System for Non-Road Single-Cylinder Diesel Engine International Journal of Research in Engineering and Science (IJRES) ISSN (Online): 2320-9364, ISSN (Print): 2320-9356 Volume 5 Issue 3 ǁ Mar. 2017 ǁ PP.17-21 Development of Fuel Injection System for Non-Road

More information

Vehicle Turn Simulation Using FE Tire model

Vehicle Turn Simulation Using FE Tire model 3. LS-DYNA Anwenderforum, Bamberg 2004 Automotive / Crash Vehicle Turn Simulation Using FE Tire model T. Fukushima, H. Shimonishi Nissan Motor Co., LTD, Natushima-cho 1, Yokosuka, Japan M. Shiraishi SRI

More information

Analysis and control of vehicle steering wheel angular vibrations

Analysis and control of vehicle steering wheel angular vibrations Analysis and control of vehicle steering wheel angular vibrations T. LANDREAU - V. GILLET Auto Chassis International Chassis Engineering Department Summary : The steering wheel vibration is analyzed through

More information

Dynamic Analysis of Double Wishbone and Double Wishbone with S Link + Toe Link

Dynamic Analysis of Double Wishbone and Double Wishbone with S Link + Toe Link RESEARCH ARTICLE OPEN ACCESS Dynamic Analysis of Double Wishbone and Double Wishbone with S Link + Toe Link Rajkumar Kewat, Anil Kumar Kundu,Kuldeep Kumar,Rohit Lather, Mohit Tomar RJIT, B.S.F ACADEMY

More information

International Industrial Informatics and Computer Engineering Conference (IIICEC 2015)

International Industrial Informatics and Computer Engineering Conference (IIICEC 2015) International Industrial Informatics and Computer Engineering Conference (IIICEC 2015) Research of Solenoid Valve CDC Damper Performance Data Compression and Fusion with Active Suspension Control Strategy

More information

ELECTRONIC CHASSIS ALIGNMENT

ELECTRONIC CHASSIS ALIGNMENT SUSPENSION Steering and Wheel Alignment - Repair Instructions - X6 ELECTRONIC CHASSIS ALIGNMENT 32... OVERVIEW OF STEERING Fig. 1: Overview Of Steering 32... OVERVIEW OF ACTIVE FRONT STEERING Fig. 2: Overview

More information

Identification of tyre lateral force characteristic from handling data and functional suspension model

Identification of tyre lateral force characteristic from handling data and functional suspension model Identification of tyre lateral force characteristic from handling data and functional suspension model Marco Pesce, Isabella Camuffo Centro Ricerche Fiat Vehicle Dynamics & Fuel Economy Christian Girardin

More information

Design Methodology of Steering System for All-Terrain Vehicles

Design Methodology of Steering System for All-Terrain Vehicles Design Methodology of Steering System for All-Terrain Vehicles Dr. V.K. Saini*, Prof. Sunil Kumar Amit Kumar Shakya #1, Harshit Mishra #2 *Head of Dep t of Mechanical Engineering, IMS Engineering College,

More information

The Institute of Mechanical and Electrical Engineer, xi'an Technological University, Xi'an

The Institute of Mechanical and Electrical Engineer, xi'an Technological University, Xi'an 6th International Conference on Mechatronics, Computer and Education Informationization (MCEI 2016) Epicyclic Gear Train Parametric esign Based on the Multi-objective Fuzzy Optimization Method Nana Zhang1,

More information

Chassis development at Porsche

Chassis development at Porsche Chassis development at Porsche Determining factors Challenges automotive industry Challenges chassis development e-mobility product differentiation customization driving resistance vehicle mass resource

More information

Comparative study between double wish-bone and macpherson suspension system

Comparative study between double wish-bone and macpherson suspension system IOP Conference Series: Materials Science and Engineering PAPER OPEN ACCESS Comparative study between double wish-bone and macpherson suspension system To cite this article: Shoaib Khan et al 2017 IOP Conf.

More information

EXPERIMENTAL INVESTIGATION IN ACCELERATION OF VEHICLES

EXPERIMENTAL INVESTIGATION IN ACCELERATION OF VEHICLES EXPERIMENTAL INVESTIGATION IN ACCELERATION OF VEHICLES Andris Linins, Dainis Berjoza Latvia University of Agriculture, Faculty of Engineering, Motor Vehicle Istitute dainis.berjoza@llu.lv Abstract. Today,

More information

Theoretical and Experimental Investigation of Compression Loads in Twin Screw Compressor

Theoretical and Experimental Investigation of Compression Loads in Twin Screw Compressor Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2004 Theoretical and Experimental Investigation of Compression Loads in Twin Screw Compressor

More information

1. SPECIFICATIONS 2. WHEEL ALIGNMENT

1. SPECIFICATIONS 2. WHEEL ALIGNMENT 441101 083 1. SPECIFICATIONS Front Suspension Rear Suspension Description Suspension type Spring type Shock absorber type Stabilizer bar type Suspension type Spring type Shock absorber type Stabilizer

More information

Analysis on Steering Gain and Vehicle Handling Performance with Variable Gear-ratio Steering System(VGS)

Analysis on Steering Gain and Vehicle Handling Performance with Variable Gear-ratio Steering System(VGS) Seoul 2000 FISITA World Automotive Congress June 12-15, 2000, Seoul, Korea F2000G349 Analysis on Steering Gain and Vehicle Handling Performance with Variable Gear-ratio Steering System(VGS) Masato Abe

More information

Design and Optimization of Suspension System of All Terrain Vehicle

Design and Optimization of Suspension System of All Terrain Vehicle Design and Optimization of Suspension System of All Terrain Vehicle Abhishek Rajput 1, Bhupendra Kasana 2, Dhruv Sharma 3, Chandan B.B 4 1, 2, 3 Under Graduate students, Dept. of Mechanical Engineering,

More information

Parametric Design and Motion Analysis of Geneva Wheel Mechanism Based on the UG NX8.5

Parametric Design and Motion Analysis of Geneva Wheel Mechanism Based on the UG NX8.5 International Conference on Manufacturing Engineering and Intelligent Materials (ICMEIM 207) Parametric Design and Motion Analysis of Geneva Wheel Mechanism Based on the UG NX8.5 En-guang Zhang*,a, and

More information

Experiment and Modeling Study on Battery Performance

Experiment and Modeling Study on Battery Performance , pp.4956 http://dx.doi.org/10.14257/astl.2016. Experiment and Modeling Study on Battery Performance Shuang Du a, Ruijuan Guo b, Shangyuan Sun c College of Engineering Technology, Jilin Agricultural University,

More information

STATIC AND FATIGUE ANALYSIS OF LEAF SPRING-AS A REVIEW

STATIC AND FATIGUE ANALYSIS OF LEAF SPRING-AS A REVIEW STATIC AND FATIGUE ANALYSIS OF LEAF SPRING-AS A REVIEW Vishal Gavali 1, Mahesh Jadhav 2, Digambar Zoman 3 1,2, 3 Mechanical Engineering Department, LGNSCOE Anjaneri Nashik,(India) ABSTRACT In engineering

More information

The Theoretical Analysis of Test Result s Errors for the Roller Type Automobile Brake Tester

The Theoretical Analysis of Test Result s Errors for the Roller Type Automobile Brake Tester The Theoretical Analysis of Test Result s Errors for the Roller Type Automobile Brake Tester Jun Li, Xiaojing Zha, and Dongsheng Wu School of Mechanical and Electronic Engineering, East China Jiaotong

More information

Aerodynamic Characteristics of Sedan with the Rolling Road Ground Effect Simulation System

Aerodynamic Characteristics of Sedan with the Rolling Road Ground Effect Simulation System Vehicle Engineering (VE) Volume 2, 2014 www.seipub.org/ve Aerodynamic Characteristics of Sedan with the Rolling Road Ground Effect Simulation System Yingchao Zhang 1, Linlin Ren 1, Kecheng Pan 2, Zhe Zhang*

More information

Chapter 2 Dynamic Analysis of a Heavy Vehicle Using Lumped Parameter Model

Chapter 2 Dynamic Analysis of a Heavy Vehicle Using Lumped Parameter Model Chapter 2 Dynamic Analysis of a Heavy Vehicle Using Lumped Parameter Model The interaction between a vehicle and the road is a very complicated dynamic process, which involves many fields such as vehicle

More information

Modal Analysis of Automobile Brake Drum Based on ANSYS Workbench Dan Yang1, 2,Zhen Yu1, 2, Leilei Zhang1, a * and Wentao Cheng2

Modal Analysis of Automobile Brake Drum Based on ANSYS Workbench Dan Yang1, 2,Zhen Yu1, 2, Leilei Zhang1, a * and Wentao Cheng2 7th International Conference on Mechatronics, Computer and Education Informationization (MCEI 2017) Modal Analysis of Automobile Brake Drum Based on ANSYS Workbench Dan Yang1, 2,Zhen Yu1, 2, Leilei Zhang1,

More information

ANALYSIS OF GEAR QUALITY CRITERIA AND PERFORMANCE OF CURVED FACE WIDTH SPUR GEARS

ANALYSIS OF GEAR QUALITY CRITERIA AND PERFORMANCE OF CURVED FACE WIDTH SPUR GEARS 8 FASCICLE VIII, 8 (XIV), ISSN 11-459 Paper presented at Bucharest, Romania ANALYSIS OF GEAR QUALITY CRITERIA AND PERFORMANCE OF CURVED FACE WIDTH SPUR GEARS Laurentia ANDREI 1), Gabriel ANDREI 1) T, Douglas

More information

1036. Thermal-hydraulic modelling and analysis of hydraulic damper for impact cylinder with large flow

1036. Thermal-hydraulic modelling and analysis of hydraulic damper for impact cylinder with large flow 1036 Thermal-hydraulic modelling and analysis of hydraulic damper for impact cylinder with large flow Y Guo, C P Liu, B W Luo Y Guo 1, C P Liu 2, B W Luo 3 1 Engineering Research Centre of Advanced Mining

More information

KINEMATICS OF REAR SUSPENSION SYSTEM FOR A BAJA ALL-TERRAIN VEHICLE.

KINEMATICS OF REAR SUSPENSION SYSTEM FOR A BAJA ALL-TERRAIN VEHICLE. International Journal of Mechanical Engineering and Technology (IJMET) Volume 8, Issue 8, August 2017, pp. 164 171, Article ID: IJMET_08_08_019 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=8&itype=8

More information

1 of 9 7/24/2014 9:02 PM

1 of 9 7/24/2014 9:02 PM 1 of 9 7/24/2014 9:02 PM Four-Wheel Alignment Special Service Tools 204-805 CAUTION: Make sure the vehicle is on a flat level surface. CAUTION: Make sure the tire pressures are within specification. CAUTION:

More information

The analysis of the accuracy of the wheel alignment inspection method on the side-slip plate stand

The analysis of the accuracy of the wheel alignment inspection method on the side-slip plate stand IOP Conference Series: Materials Science and Engineering PAPER OPEN ACCESS The analysis of the accuracy of the wheel alignment inspection method on the side-slip plate stand To cite this article: A Gajek

More information

Study on Dynamic Behaviour of Wishbone Suspension System

Study on Dynamic Behaviour of Wishbone Suspension System IOP Conference Series: Materials Science and Engineering Study on Dynamic Behaviour of Wishbone Suspension System To cite this article: M Kamal and M M Rahman 2012 IOP Conf. Ser.: Mater. Sci. Eng. 36 012019

More information

ANALYSIS OF SUSPENSION ELEMENT OF CAR BODY ON THE EXAMPLE SILENTBLOCK

ANALYSIS OF SUSPENSION ELEMENT OF CAR BODY ON THE EXAMPLE SILENTBLOCK Advances in Science and Technology Research Journal Volume 9, No. 28, Dec. 2015, pages 125 129 DOI: 10.12913/22998624/60799 Research Article ANALYSIS OF SUSPENSION ELEMENT OF CAR BODY ON THE EXAMPLE SILENTBLOCK

More information

Steering drift and wheel movement during braking: static and dynamic measurements

Steering drift and wheel movement during braking: static and dynamic measurements 11 Steering drift and wheel movement during braking: static and dynamic measurements J Klaps1 and AJDay2* 1Ford Motor Company, Ford-Werke Aktiengesellschaft, Fabriekente Genk, Genk, Belgium 2University

More information

Prediction of wheel/rail rolling contact wear under the situation of wheel/rail vibration

Prediction of wheel/rail rolling contact wear under the situation of wheel/rail vibration First International Conference on Rail Transportation Chengdu, China, July 10-12, 2017 Prediction of wheel/rail rolling contact wear under the situation of wheel/rail vibration Qian XIAO1,2 Chao CHANG1,

More information

Power Matching Strategy Modeling and Simulation of PHEV Based on Multi agent

Power Matching Strategy Modeling and Simulation of PHEV Based on Multi agent Power Matching Strategy Modeling and Simulation of PHEV Based on Multi agent Limin Niu* 1, Lijun Ye 2 School of Mechanical Engineering, Anhui University of Technology, Ma anshan 243032, China *1 niulmdd@163.com;

More information

Development of a Multibody Systems Model for Investigation of the Effects of Hybrid Electric Vehicle Powertrains on Vehicle Dynamics.

Development of a Multibody Systems Model for Investigation of the Effects of Hybrid Electric Vehicle Powertrains on Vehicle Dynamics. Development of a Multibody Systems Model for Investigation of the Effects of Hybrid Electric Vehicle Powertrains on Vehicle Dynamics. http://dx.doi.org/10.3991/ijoe.v11i6.5033 Matthew Bastin* and R Peter

More information

Development and Control of a Prototype Hydraulic Active Suspension System for Road Vehicles

Development and Control of a Prototype Hydraulic Active Suspension System for Road Vehicles Development and Control of a Prototype Hydraulic Active Suspension System for Road Vehicles Suresh A. Patil 1, Dr. Shridhar G. Joshi 2 1 Associate Professor, Dept. of Mechanical Engineering, A.D.C.E.T.,

More information

MARINE FOUR-STROKE DIESEL ENGINE CRANKSHAFT MAIN BEARING OIL FILM LUBRICATION CHARACTERISTIC ANALYSIS

MARINE FOUR-STROKE DIESEL ENGINE CRANKSHAFT MAIN BEARING OIL FILM LUBRICATION CHARACTERISTIC ANALYSIS POLISH MARITIME RESEARCH Special Issue 2018 S2 (98) 2018 Vol. 25; pp. 30-34 10.2478/pomr-2018-0070 MARINE FOUR-STROKE DIESEL ENGINE CRANKSHAFT MAIN BEARING OIL FILM LUBRICATION CHARACTERISTIC ANALYSIS

More information

WHEEL ALIGNMENT PROCEDURES

WHEEL ALIGNMENT PROCEDURES Page 1 of 8 WHEEL ALIGNMENT PROCEDURES TURNING ANGLE Turn steering wheel fully right and then left, and observe turning radius on both wheels. If turning radius is incorrect, inspect and replace any damaged

More information

Design of Damping Base and Dynamic Analysis of Whole Vehicle Transportation based on Filtered White-Noise GongXue Zhang1,a and Ning Chen2,b,*

Design of Damping Base and Dynamic Analysis of Whole Vehicle Transportation based on Filtered White-Noise GongXue Zhang1,a and Ning Chen2,b,* Advances in Engineering Research (AER), volume 07 Global Conference on Mechanics and Civil Engineering (GCMCE 07) Design of Damping Base and Dynamic Analysis of Whole Vehicle Transportation based on Filtered

More information

SUMMARY OF STANDARD K&C TESTS AND REPORTED RESULTS

SUMMARY OF STANDARD K&C TESTS AND REPORTED RESULTS Description of K&C Tests SUMMARY OF STANDARD K&C TESTS AND REPORTED RESULTS The Morse Measurements K&C test facility is the first of its kind to be independently operated and made publicly available in

More information

MODELING AND SIMULATION OF INTERNAL CIRCULATION TWO-PLATEN INJECTION MOLDING MACHINE BASED ON AMESIM

MODELING AND SIMULATION OF INTERNAL CIRCULATION TWO-PLATEN INJECTION MOLDING MACHINE BASED ON AMESIM MODELING AND SIMULATION OF INTERNAL CIRCULATION TWO-PLATEN INJECTION MOLDING MACHINE BASED ON AMESIM Lu Yang, Jiong Peng, Dongjie Chen and Jian Wang* Beijing Institute of Technology, Beijing 100081, China

More information

Fundamentals of Steering Systems ME5670

Fundamentals of Steering Systems ME5670 Fundamentals of Steering Systems ME5670 Class timing Monday: 14:30 Hrs 16:00 Hrs Thursday: 16:30 Hrs 17:30 Hrs Lecture 3 Thomas Gillespie, Fundamentals of Vehicle Dynamics, SAE, 1992. http://www.me.utexas.edu/~longoria/vsdc/clog.html

More information