Doc: TED 7(743)W November 2009 Draft Indian Standard AUTOMOTIVE VEHICLES TUBES FOR PNEUMATIC TYRES SPECIFICATION (First Revision of IS 13098)

Size: px

Start display at page:

Download "Doc: TED 7(743)W November 2009 Draft Indian Standard AUTOMOTIVE VEHICLES TUBES FOR PNEUMATIC TYRES SPECIFICATION (First Revision of IS 13098)"

Ronald Todd
5 years ago
Views:

1 For BIS Use Only Doc: TED 7(743)W November 2009 Draft Indian Standard AUTOMOTIVE VEHICLES TUBES FOR PNEUMATIC TYRES SPECIFICATION (First Revision of IS 13098) 0 FOREWORD (Formal Clause. Will be added later on) This standard was first published in The first revision is based on the experience gained after publication of the standard. This standard has been revised to keep pace with the latest technological advancement in the field of tubes for automotive vehicles. This revision has been undertaken after due consideration of the practices prevalent in the industry. Assistance has been derived from the following publication while preparing this standard: JIS D 4231 : 1995 Inner tubes for automobiles tyres, issued by the Japanese Industrial Standards Committee (JISC) For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated, expressing the result of a test or analysis, shall be rounded off in accordance with IS 2:1960 `Rules for rounding off numerical values (revised)'. The number of significant places retained in the rounded off value shall be the same as that of the specified value in this standard. 1 SCOPE 1.1 This Indian Standard specifies the requirements of tubes for pneumatic tyres for automotive vehicles covered by M1, T1, T2, M2, M3, N, T3,T4 and two and three wheelers as defined in IS 14272: REFERENCES The following standards contain provisions, which, through reference in this text, constitute provisions of this standard. At the time of publication the editions indicated was valid. All standards are subject to revision and parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent edition of the standard indicated below. IS No. 3400(Part 1):1987 Title Methods of test for vulcanized rubbers Part 1 Tensile stress strain properties (second revision) 9081: 2001 Automotive vehicles Valves and valve accessories for pneumatic tyres Specification (third revision) 14272:2009 Automotive vehicles Types, Terminology 3 MATERIALS, FORM AND FIT 3.1 The tubes shall be manufactured from an appropriate rubber compound and vulcanized to an end less annular ring shape and shall be with a valve or spud conforming to IS The tubes shall be classified into the following two classes: a) Class A Butyl rubber / Halo-butyl rubber and its derivative and blends, and b) Class B Natural Rubber and its derivatives and blends 1

2 3.3 The tube shall be uniform in thickness, free from flaws and designed to fit in a tyre of the corresponding nominal size Thickness Uniformity Except for the region at or near lap or splice the thickness of the tube when measured along the longitudinal direction of the tube, shall not vary from the arithmetic mean of the readings by ± 17.5 percent at any point The arithmetic mean of the tube thickness shall be determined for the points which lie in the same circumferential line or the length of the tube. The thickness variation shall be determined for each of the four circumferential lines, that is crown centre, base centre, right side wall centre and left side wall centre. 4 MARKINGS Fig. 1 Measurement of Tube Thickness Uniformity Tubes shall be permanently and legibly marked on the outside the following. 4.1 Make (manufacturer s name) or trade name. 4.2 Tyre size designation or designation for which the tube is applicable. The size designation description shall contain: a) Nominal tyre section width code; b) Nominal rim diameter code; c) Nominal aspect ratio, if applicable; and d) R to identify Radial tyre application. 4.3 Indication of month and year of manufacturing as per scheme given in Annex A. 4.4 The word BUTYL and or blue line of 3 mm minimum width to identify tube of class A. 5 TEST REQUIREMENTS 5.1 Each type of tube shall conform to the following requirements Elongation Dumbbell test pieces punched out in circumferential direction of the tube when tested in accordance IS 3400(Part 1):1987 and Annex B shall have elongation at break not less than 450% for Class A tubes and not less than 500% for Class B tubes. 2

3 5.1.2 Strength of Splice Tensile strength of splice determined on dumbbell in accordance with IS 3400(Par1):1987 and Annex B shall not be less than 35 kgf/cm² for class A tubes and 85 kgf/cm² for Class B tubes Set after Ageing Dumb bell test pieces punched out in circumferential direction of the tube when subjected to test conditions and test procedure in accordance with Annex C shall have set after aging not more than 35% for class A tubes and not more than 25% for class B tubes Accelerated Aging Dumbbell test pieces punched out in circumferential direction of the tube body when subjected to accelerated aging test as 100 ±ºC for 48 hrs and tested in accordance with IS 3400(Part 1):1987 and Annex D shall not have drop in elongation at break more than 35% from original, for both class A and class B tubes. 6 AIR TIGHTNESS Each type of tube with valves attached shall be inflated to just round out and tested in water for the evidence of any leakage. Alternatively, vacuum leak or pressure-less detection method may be used as per the manufacturers practice in lieu of the water test method. The tube shall not show any leakage or defective workmanship. 7 SAMPLING The scale of sampling and the criteria of acceptance shall be as agreed to between the manufacturer and the purchaser. 8 BIS CERTIFCATION MARKING The product may also be marked with the Standard Mark. The use of the Standard Mark is governed by the provisions of the Bureau of Indian Standards Act and the Rules and Regulations made there under. The detail of conditions under which the license for the use of Standard Mark may be rated to manufacturers or producers may be obtained from the Bureau of Indian Standards. 3

4 ANNEX A (Clause 4.3) IDENTIFICATION SCHEME FOR MONTH AND YEAR OF MANUFACTURING A-1 IDENTIFICATION SCHEME A-1.1 Manufacturing Month and Year are engraved as per scheme depicted in Fig. 2. A-1.2 Month code circle and year to be engraved 100 mm right to the valve block in the bottom half mould. A-1.3 Quarters are as per the calendar year, for example Quarter-1 January-March, Quarter-2 April- June, Quarter-3 July-September and Quarter-4 October-December. A-1.4 Each month should be identified by a punch marking of at least 0.5 mm diameter in the respective Quarter. A-1.5 After completing one year, fresh identification shall be started again for the next year with next circle. A-1.6 After completing all three circles, re-engraving can be done after masking the previous engraving/punch marking. A-1.7 Alternative method which clearly indicates the month and year of manufacturing is also acceptable. Fig. 2 Scheme of marking Month and Year on Tube (Example: Identification for April 2008 depicted in the drawing above) 4

5 ANNEX B (Clause 5.1.1) PREPARATION OF DUMB-BELL TEST SPECIMEN FROM TUBE B-1 PREPARATION OF TEST PIECES B-1.1 Test pieces shall be the dumbbell shape and to be taken in the circumferential direction of a tube, from portion except the splice joint for the elongation test. For testing strength of joint splice, dumbbell shall be punched out from the splice joint as the centre as shown in the Fig. 2. B-1.2 The number of test pieces shall be 4 each from a tube. Size of test pieces shall be 6mm (or 13mm) dumbbell test pieces, for measurement of tensile strength. B-1.3 The mean value of both ends of parallel parts shall be used as the thickness of test pieces for calculating the tensile strength of splice joints. B-1.4 For elongation and tensile strength of joints, measured median value of 4 test pieces shall be used. Fig. 3 Method of Taking Test Pieces 5

6 ANNEX C (Clause 5.1.3) TEST CONDITIONS AND TEST PROCEDURE FOR SET AFTER AGEING C-1 TEST CONDITIONS FOR AGEING Type of Oven : Air Oven Temperature : 104ºC to 110ºC Time to be kept in oven : 5 Hours Dimensions of test piece : 6 mm wide 25 mm long measured on 6 mm dumbbell Stretch of test piece during : 50 percent ageing C-2 DETERMINATION OF THE SET The test piece shall be removed from oven and allowed to cool under tension for 2 hours. The tension shall be released and percentage set measured after a rest of not less than 8 hours or more than 24 hours. 6

7 ANNEX D (Clause 5.1.4) ACCELERATED AGEING TEST D-1 PREPARING THE TEST PIECES Prepare 4 test pieces as specified in Annex B and subject them to the accelerated ageing for 100 ± 2 ºC for 48 hours. D-2 MEASURING THE TENSILE STRENGTH Measure the tensile strength in accordance with IS 3400(Part 1):1987 and then calculate the percentage drop in elongation at break compared with respective un-aged elongation at break from the following formula: PDEB = (L a L o ) 100 L o Where, PDEB : Percent drop in Elongation at break after ageing L o : Median value of Elongation at break percentage before ageing test : Median value of Elongation at break percentage after ageing test L a 7

8 दरभ ष : श ख : 4348 ट ल फ स: य पक प रच लन म मस द ई-म ल: ted@bis.org.in ल ख षण स चन ट ईड 7/ ट -3 जनवर वचल ट यर, टय ब और रम वषय स म त, ट ईड 7 कú) प रवहन इ ज नय र ग वभ ग प रषद ü (पइ वप) क च रखन व ल सद य ख) चचल ट यर, टय ब और रम वषय स म त, ट ईड 7 ग) अ य च रखन व ल सद य मह दय, न न ल खत ल ख स लगन ह, तथ यह ल ख पहल ईम ल र 20 Nov 2009 क, जसम ट प णय भ जन क अ तम त थ: भ ज च क ह, अ त: अब आपक ह ड क प दन क तथ ट पण बदल कर भ ज रह ह ल ख स य ट ईड 7(743) W वषय वचल व हन - हव भर ट यर क टय ब प नर ण आई एस 13098) - व श ट (पहल क य उपर त म नक मस द क अवल कन कर अपन ट प णय यह बत त हए भ ज, क य द अ तत: यह म नक र श य म नक क प म व क त ह ज ए, त इस पर अमल करन म आपक यवस य अथव क र ब र म य क ठन इय आ सकत ह ट प णय भ जन क अ तम त थ: ट पण य द क ई ह त स ल न प म लख कर द, तथ ऊपर ल खत पत पर अध ह त र क ड क र षत कर ल ख भ म य र क व वस ईट पर भ उपल ध ह ध यव द, भवद य, स लगन: ऊपर ल खत ( ट व स ) व नक ई एव म ख (ट ईड ) 8

9 Please Contact at Phone: /4348 Telefax: , DRAFT IN WIDE CIRCULATION AUTOMOTIVE TYRES, TUBES AND RIMS SECTIONAL COMMITTEE, TED 7 ADDRESSED TO: 1. All Interested Members of Transport Engineering Division Council, TEDC 2. All Members of Automotive Tyres, Tubes and Rims Sectional Committee, TED 7 3. All Others Interested. Dear Sir(s), DOCUMENT DESPATCH ADVICE Ref. Date TED 7/T Please find enclosed the following draft Indian Standard, which was circulated by 20 Nov 2009 by indicating last date of comments 20 Jan Hard copy is being circulated with modified date and comments as indicated. Doc No. Title TED 7(743) W AUTOMOTIVE VEHICLES TUBES FOR PNEUMATIC TYRES SPECIFICATION (First Revision of IS 13098) Kindly examine this draft Indian standard and forward your views stating any difficulties which you are likely to experience in your business or profession, if this is finally adopted as National Standards. Last date for comments: Comments, if any, may please be made in the enclosed format and mailed to the undersigned at the above address. This document is also available on BIS website Thanking you, Yours faithfully, Encl.: As above 9 (T.V. Singh) Sc `E & Head (Transport Engg.)

10 FORMAT FOR SENDING COMMENTS ON BIS DOCUMENTS [Please use A4 size paper only and type within fields indicated. Comments on each clause/sub-clause be started on a fresh paper. Information in column 3 should include reasons for the comments and suggestions for modified wording of the clause when the existing text is found not acceptable. Adherence to this format facilitates Secretariat s work] NAME OF THE COMMENTATOR/ORGANIZATION DOC NUMBER AND TITLE: SL. NO. (1) Clause/Sub-clause/ Para No. Commented (2) COMMENTS/SUGGESTIONS (3) 10

Comments, if any, may please be made in the enclosed format and mailed to the undersigned at the above address.

Comments, if any, may please be made in the enclosed format and mailed to the undersigned at the above address. DRAFT IN WIDE CIRCULATION DOCUMENT DESPATCH ADVICE Ref. Date TED 6/T - 56 & 31 25-01-2012 AUTOMOTIVE BODY, CHASSIS, ACCESSORIES AND GARAGE EQUIPMENT SECTIONAL COMMITTEE, TED 6 ADDRESSED TO: 1. All Interested