Analysis of Composite Materials with Abaqus 6.14

Transcription

1 Analysis of Composite Materials with Abaqus 6.14

2 About this Course Course objectives Upon completion of this course you will be able to: Define anisotropic elasticity for combining the fiber-matrix response Define composite layups Model sandwich composite structures and stiffened composite panels Model progressive damage and failure in composites Model delamination and low-cycle fatigue of composite structures Targeted audience Simulation Analysts Prerequisites This course is recommended for engineers with experience using Abaqus 3 days

3 Day 1 Lecture 1 Introduction Lecture 2 Macroscopic Modeling Lecture 3 Mixed Modeling Workshop 1 The Pagano Plate Problem Lecture 4 Composite Modeling with Abaqus Workshop 2a Buckling of a Laminate Panel Workshop 2b Composite Wing Section Workshop 3 Composite Yacht Hull (Optional)

4 Day 2 Lecture 5 Reinforcement Modeling Lecture 6 Modeling of Sandwich Composites Workshop 4 Bending of a Sandwich Beam Lecture 7 Modeling of Stiffened Panels Workshop 5 Bending of a Reinforced Flat Panel under Uniform Pressure Lecture 8 Modeling Damage and Failure in Composites

5 Day 3 Lecture 9 Cohesive Behavior Workshop 6 Analysis of a DCB using Cohesive Behavior Lecture 10 Virtual Crack Closure Technique (VCCT) Workshop 7 Analysis of a DCB using VCCT (Abaqus/Standard) Workshop 8 Analysis of a DCB using VCCT (Abaqus/Explicit) Lecture 11 Low-cycle Fatigue Workshop 9 Fatigue Crack Growth in a DCB Specimen

6 Additional Material Appendix 1 Debond Capability Appendix 2 Cohesive Element Modeling Techniques Appendix 3 More on Continuum Shell Elements Appendix 4 Alternative Modeling Techniques Appendix 5 Modeling Composite Material Impact Workshop 10 Perforation of a Composite Plate Appendix 6 Material Orientation Examples

7 Join the Community!

8 Legal Notices The Abaqus Software described in this documentation is available only under license from Dassault Systèmes or its subsidiary and may be used or reproduced only in accordance with the terms of such license. This documentation and the software described in this documentation are subject to change without prior notice. Dassault Systèmes and its subsidiaries shall not be responsible for the consequences of any errors or omissions that may appear in this documentation. No part of this documentation may be reproduced or distributed in any form without prior written permission of Dassault Systèmes or its subsidiary. Dassault Systèmes, 2014 Printed in the United States of America. Abaqus, the 3DS logo, SIMULIA, and CATIA are trademarks or registered trademarks of Dassault Systèmes or its subsidiaries in the US and/or other countries. Other company, product, and service names may be trademarks or service marks of their respective owners. For additional information concerning trademarks, copyrights, and licenses, see the Legal Notices in the Abaqus 6.14 Installation and Licensing Guide.

9 Revision Status Lecture 1 5/14 Updated for 6.14 Lecture 2 5/14 Updated for 6.14 Lecture 3 5/14 Updated for 6.14 Lecture 4 5/14 Updated for 6.14 Lecture 5 5/14 Updated for 6.14 Lecture 6 5/14 Updated for 6.14 Lecture 7 5/14 Updated for 6.14 Lecture 8 5/14 Updated for 6.14 Lecture 9 5/14 Updated for 6.14 Lecture 10 5/14 Updated for 6.14 Lecture 11 5/14 Updated for 6.14 Workshop 1 5/14 Updated for 6.14 Workshop 2a 5/14 Updated for 6.14 Workshop 2b 5/14 Updated for 6.14 Workshop 3 5/14 Updated for 6.14 Workshop 4 5/14 Updated for 6.14 Workshop 5 5/14 Updated for 6.14 Workshop 6 5/14 Updated for 6.14 Workshop 7 5/14 Updated for 6.14 Workshop 8 5/14 Updated for 6.14 Workshop 9 5/14 Updated for 6.14 Workshop 10 5/14 Updated for 6.14 Appendix 1 5/14 Updated for 6.14 Appendix 2 5/14 Updated for 6.14 Appendix 3 5/14 Updated for 6.14 Appendix 4 5/14 Updated for 6.14 Appendix 5 5/14 Updated for 6.14 Appendix 6 5/14 Updated for 6.14

10 Lesson 1: Introduction L1.1 Lesson content: Description of a Composite Some Typical Composites Finite Element Modeling of Composites 20 minutes

11 Lesson 2: Macroscopic Modeling L2.1 Lesson content: Introduction Anisotropic Elasticity Viscoelasticity Thermal Expansion Material Orientation 45 minutes

12 Lesson 3: Mixed Modeling L3.1 Lesson content: Introduction Laminated Composite Shells Continuum Shell Elements Continuum Shell Meshing Continuum Solid Elements Symmetry Conditions and Laminated Structures Workshop Preliminaries Workshop 1: The Pagano Plate Problem 3 hours

13 Lesson 4: Composite Modeling with Abaqus L4.1 Lesson content: Introduction Understanding Composite Layups Understanding Composite Layup Orientations Defining Composite Layup Output Viewing a Composite Layup Abaqus/CAE Demonstration: Three-ply composite Composites Modeler for Abaqus/CAE Workshop 2a: Buckling of a Laminate Panel Workshop 2b: Composite Wing Section Workshop 3: Composite Yacht Hull 3 hours

14 Lesson 5: Reinforcement Modeling L5.1 Lesson content: Introduction Rebar Layers Embedded Elements 45 minutes

15 Lesson 6: Analysis of Sandwich Composites L6.1 Lesson content: Introduction to Sandwich Composites Abaqus Usage Modeling Skins with Abaqus/CAE Abaqus Examples Comparison to NAFEMS solution Comparison of Conventional and Continuum Shells Stacking Elements Through the Thickness Tapered Sandwich Composite Workshop 4: Bending of a Sandwich Beam 1.5 hours

16 Lesson 7: Analysis of Stiffened Composite Panels L7.1 Lesson content: Stiffened Composite Panels Abaqus Usage Abaqus Example Workshop 5: Bending of a Reinforced Flat Panel under Uniform Pressure 2 hours

17 Lesson 8: Modeling Damage and Failure in Composites L8.1 Lesson content: Failure Criteria in Laminates Failure Theories Progressive Damage of Fiber-Reinforced Composites Example Import of Composite Damage Model 75 minutes

18 Lesson 9: Cohesive Behavior L9.1 Lesson content: Introduction Cohesive Element Technology Constitutive Response in Cohesive Elements Viscous Regularization for Cohesive Elements Cohesive Element Examples Surface-based Cohesive Behavior Element- vs. Surface-based Cohesive Behavior Workshop 6: Analysis of a DCB using Cohesive Behavior Note: Appendix 2 contains an in-depth discussion of modeling techniques for cohesive elements using both the interactive and keywords interfaces. 3 hours

19 Lesson 10: Virtual Crack Closure Technique (VCCT) L10.1 Lesson content: Introduction VCCT Criterion LEFM Example using Abaqus/Standard LEFM Example using Abaqus/Explicit Output Ductile Fracture with VCCT VCCT Plug-in Comparison with Cohesive Behavior Examples Workshop 7: Analysis of a DCB using VCCT (Abaqus/Standard) Workshop 8: Analysis of a DCB using VCCT (Abaqus/Explicit) 3 hours

20 Lesson 11: Low-cycle Fatigue L11.1 Lesson content: Introduction Direct Cyclic Low-cycle Fatigue Analysis Low-cycle Fatigue Criterion Workshop 9: Fatigue Crack Growth in a DCB Specimen 1 hour

21 Appendix 1: Debond Capability A1.1 Appendix content: Introduction Modeling Interface Behavior 30 minutes

22 Appendix 2: Cohesive Element Modeling Techniques A2.1 Appendix content: Viscous Regularization Modeling Techniques 1 hour

23 Appendix 3: More on Continuum Shell Elements A3.1 Appendix content: Defining the thickness direction for continuum shell elements Shell thickness Change in thickness and thickness modulus 1 hour

24 Appendix 4: Alternative Modeling Techniques A4.1 Appendix content: Introduction Laminated Shell Section Definition Laminated Solid Section Definition Section Point Based Postprocessing Technique 1 hour

25 Appendix 5: Modeling Composite Material Impact A5.1 Appendix content: Introduction Composite Damage Models in Abaqus/Explicit Unidirectional Fiber Example Composite Plate Impact Woven Fabric Example Corrugated Beam Crushing Modeling Techniques Workshop 10: Perforation of a Composite Plate 1.5 hours

26 Appendix 6: Material Orientation Examples A6.1 Appendix content: Example 3: Shell elements Example 4: Layered shell elements Example 5: Solid elements Example 6: Layered solid elements 30 minutes