CRASH TEST REPORT FOR PERIMETER BARRIERS AND GATES TESTED TO SD-STD-02.01, REVISION A, MARCH Anti-Ram Bollards

Size: px
Start display at page:

Download "CRASH TEST REPORT FOR PERIMETER BARRIERS AND GATES TESTED TO SD-STD-02.01, REVISION A, MARCH Anti-Ram Bollards"

Transcription

1 CRASH TEST REPORT FOR PERIMETER BARRIERS AND GATES TESTED TO SD-STD-02.01, REVISION A, MARCH 2003 Anti-Ram Bollards Prepared for: RSA Protective Technologies, LLC 1573 Mimosa Court Upland, CA Test Report No. KARCO Engineering, LLC AUTOMOTIVE RESEARCH CENTER 9270 Holly Road Adelanto, CA Tel: (760) Fax: (760) April 4, 2005

2 KARCO Engineering compiled this publication for information gathering only. The opinions, findings and conclusions expressed in this publication are those of the authors and not necessarily those of any other organization. KARCO Engineering provides test services only and is not involved in consulting, product design or the manufacturing of any automotive products. KARCO does not warrant, supervise or monitor compliance of products or services except as specifically agreed to in writing. By their very nature, testing, analysis and other KARCO services are limited in scope and subject to expected measurement variability. No activity by KARCO Engineering can release a manufacturer from product or any other liability. Tested By: Reviewed By: Approved By: Approval Date: Mr. Matthew A. Ivory, Project Manager Mr. Michael L. Dunlap, Quality Assurance Mr. Frank D. Richardson, Program Manager

3 TABLE OF CONTENTS Section Page 1 Introduction 1 2 Test Procedure and Instrumentation Summary 2 3 Test Results and Data Sheets 5 Table Page 1 Test Designations 2 Data Sheet Page 1 Test Vehicle Information 6 2 Test Vehicle Geometry 7 3 Evaluation of Test Results 8 4 Vehicle Accelerometer Data Summary 9 5 Camera Views and Film Speeds 10 Appendix Page A Photographs A B Data Plots B C Instrumentation List C D Manufacturers Drawings D i

4 LIST OF PHOTOGRAPHS Figure Page 1 Test Article as Received A-1 2 Right Front View at Test Article` A-1 3 Anti-Ram Bollard 5 inch Footing A-2 4 Bollard 10 inch Diameter and 1 inch Wall Thickness A-2 5 Bollard Foundation Module Front View and Re-bar A-3 6 Bollard Foundation Module Rear View A-3 7 Excavation A-4 8 Embedment Depth A-4 9 Test Article Positioned in Place A-5 10 Test Article During Installation A-5 11 Test Article During Installation A-6 12 Test Article During Installation A-6 13 Test Article Left Side View A-7 14 Test Article Left Front ¾ View A-7 15 Test Article Front View A-8 16 Test Set-Up A-8 17 Test Set-Up A-9 18 Test Set-Up A-9 19 Test Set-Up A Test Set-Up A Test Set-Up A Test Set-Up A Test Article Orientation to Front Bumper A Test Article Orientation to Front Bumper A Test Set-Up A Ballast A Post-Test Left Side View A Post-Test Left Side view Close-Up A Post-Test Front View A Post-Test Overhead View A Post-Test Test Article Front View A Post-Test Test Article Left Side View A Post-Test Test Article Left Side View A Center Bollard Deflection A Ballast A Action Sequence 1 A Action Sequence 2 A Action Sequence 3 A Action Sequence 4 A-20 ii

5 TABLE OF CONTENTS...(CONTINUED) LIST OF DATA PLOTS Plots Page B-1 Vehicle Rear Frame Rail X B-1 Vehicle Rear Frame Rail Y B-1 Vehicle Rear Frame Rail Z B-1 Vehicle Rear Frame Rail Resultant B-1 B-2 Vehicle Rear Frame Rail X Velocity B-2 Vehicle Rear Frame Rail X Displacement B-2 Table INSTRUMENTATION LIST Page C-1 Instrument Data Channel Assignments C-1 Figure MANUFACTURERS DRAWINGS Page 1 Manufacturers Test Article Layout Drawing D-1 iii

6 SECTION 1 INTRODUCTION 1.1 OBJECTIVES The primary objective of this crash test was to determine if the tested vehicle impact-rated barrier meets the minimum performance standards of the United States Department of State Specification for Vehicle Crash Testing of Perimeter Barriers and Gates (SD-STD-02.01, Revision A). This report presents the results of the performance and evaluation of one (1) full-scale crash test conducted on an RSA Anti-Ram Bollard system with 5 inch footings (ID=K8B5F5T). All tests were conducted in accordance with current SD-STD-02.01, Revision A, requirements for test designation K4. Procedures for receiving, inspecting, installation, testing and reporting of test results are described in the test procedure and are not repeated in this report. The purpose of this test was to evaluate the crash performance of the Anti-Ram Bollards. 1.2 TEST FACILITY All tests were conducted at KARCO Engineering s crash test facility in Adelanto, California. The tow road is constructed of reinforced concrete, presents a continuous level surface, and measures 850 feet in length. The width of the tow road is twelve feet with a thickness of six inches. A steel rail is embedded in the approach surface to provide vehicle guidance. Vehicle tow propulsion is provided by a 1 ton truck using a 2-to-1 pulley system coupled to a fixed prime mover (an internal combustion engine, Chevrolet V-8, 454 cubic inches displacement, with T-400 automatic transmission) and continuous cable drive system. The test vehicle is towed to within two feet of the barricade by a nylon rope clamped to a 3/8-inch steel cable. The clamp is released from the cable on contact with a cable release mechanism positioned to allow the test vehicle to proceed under its own momentum for the final two feet of travel before impacting the test array. 1.3 TEST ARTICLE Unit consists of 5, 40 inch high, 10 inch diameter Anti-Ram Bollards. The bollards have a 1 inch wall thickness and are filled with concrete during installation. Bollards are equally spaced at a distance of 4 foot 6 inches center to center. The system has a 5 inch footing that is installed 1.5 inches below the level concrete surface. 1

7 SECTION 2 TEST PROCEDURE AND INSTRUMENTATION SUMMARY 2.1 TEST PROCEDURE To meet the recommended properties of SD-STD Rev A. impact requirements, a commercially available production model test vehicle was selected. This test was conducted using a 1987 International S1900, medium duty truck with conventional cab, front mounted diesel engine, rear wheel drive and an automatic transmission. The vehicle was in good condition, was free of major body damage, and was not missing any structural components. The bumpers were standard equipment and were not modified for this test. The materials, assembly instructions and physical configuration of the test article are specified in the manufacturer s documentation and are not repeated in this test report. Installation of the test article was conducted by the manufacturer. The test article, as installed at the test facility, is illustrated in Appendix A. 2.2 IMPACT CONDITIONS As recommended in SD-STD Rev A test specification, the following full-scale crash test was conducted to evaluate the impact performance of the Anti-Ram Bollards. The primary intent of this test is to evaluate the ability of the bollards to arrest a 15,000 pound vehicle from penetrating or vaulting into a secured area and the extent, if any, of barrier deformation Test Mass. The specific mass (gross weight) of the test vehicle as specified in the standard is 15,000 pounds (lb.) ±200 lb. The test weight, with instrumentation and ballast, was 15,142 lb Speed. Vehicle speed at impact with the test article shall be dependent on the condition designation as outline in Table 1. For this test designated as K4, the velocity at impact was mph. Table 1. Test Designations IMPACT SPEED (mph) CONDITION DESIGNATION MINIMUM NOMINAL MAXIMUM K K K

8 2.2.3 Approach Angle and Impact Point. The test vehicle is oriented such that it approaches the test article at a critical impact angle of ninety degrees (90 ±3º), relative to the roadway, with the centerline of the vehicle impacting the test article at the impact point designated by the DOS Technical Representative. The actual center of the impact point must be within ± 1 foot (ft.) of the target. The impact point designated for this test was the middle of the test article. The actual point of impact was perpendicular to and within 2 inches of the target. 2.3 TEST INSTRUMENTATION AND DATA ACQUISITION PROCEDURES All testing and data acquisition for this RSA Anti-Ram Bollard system with 5 inch footings (ID=K8B5F5T) certification test was performed in accordance with the SD-STD Revision A test specification requirements. Appendix C contains a list of the instrumentation used in the performance of this test On-Board Data Acquisition. MDAS is an acronym for Miniature Data Acquisition System. The system is comprised of a 3-channel module. The module functions as a stand-alone, all-in-one unit with integral tri-axial accelerometer, computer control, signal conditioning, A/D circuitry, memory storage and battery pack. All functions are controlled by an off-board notebook or other PC compatible computer. Once the off-board computer initializes the system, it is designed to collect data with no off-board support Test Vehicle Instrumentation. Located near the vehicle rear frame rail, the test vehicle was instrumented with a tri-axial accelerometer to measure longitudinal (x), lateral (y) and vertical (z) acceleration. Data was recorded using the on-board MDAS three (3) channel module. Data was linked to a personal computer and processed using the MDAS crash test software. All equipment used in this test meets the requirements of SAE J TDAS Software. The software utilized in this system is written in National Instruments LabWindows/CVI (C, Visual Interface) programming language, which is a Windows based (3.1 or Windows 95) software package with emphasis on ease of use and good engineering test practices SAE Compatibility. The software contains standard point and click processing options for selecting Society of Automotive Engineers (SAE) class post filters and calculating the required integrals, resultants, Head Injury Criteria (HIC), clips, and other data processing parameters that may be required. 3

9 2.3.5 Photographic Documentation. Photographic documentation of this test included three (3) realtime video cameras and (4) high-speed color digital video cameras at 1000 fps set up for an overhead view, a driver side view perpendicular to the point of impact a driver side view with a pre-determined angle to the point of impact and a frontal view. All high-speed cameras were activated by a pressure sensitive tape switch, which was positioned on the test article to indicate the instant of contact (time zero). A digital still camera was used for documenting the pre- and post-test condition of the test vehicles and Anti Ram Bollards Test Article Instrumentation. None 4

10 SECTION 3 TEST RESULTS AND DATA SHEETS 3.1 TEST DESIGNATION K8 This thirty miles per hour (32.28 mph) frontal impact crash test was conducted using a commercially available 1987 International S1900, medium duty truck to determine if the tested vehicle impact-rated bollards meet the minimum performance standards of SD-STD Rev. A. The primary intent of this test was to evaluate the ability of the barrier to arrest a 15,000-pound vehicle from penetrating or vaulting into a secured area and the extent, if any, of bollard deformation. This was accomplished by measuring the vehicle penetration at the specified level of kinetic energy. The test article was positioned at an angle of ninety degrees (90 ) to the direction of travel of the impacting test vehicle, with the vehicle s centerline impacting the middle section of the bollard system. The vehicle was instrumented with a tri-axial accelerometer at the rear frame rail. This crash test was documented by three (3) real-time video cameras, and four (4) high-speed digital color cameras. Photographs of the test vehicle and the anti ram bollards are shown in Appendix A. 3.2 PRIMARY TEST RESULTS Test K4 was conducted on April 4, The test inertial weight of the vehicle was 15,142 lb. Test vehicle information is presented in Data Sheet No. 1 and Data Sheet No. 2. The test vehicle impacted the center of the barrier gate at a velocity of mph. The evaluation of the anti ram bollard performance is presented in data Sheet No. 3. The vehicle was completely arrested by the barrier system. Pre- and Post-test photographs of the impact vehicle as well as of the bollards are shown Appendix A. Data plots of the event are presented in appendix B. The vehicle sustained severe damage to the entire cab. 5

11 DATA SHEET NO. 1 TEST VEHICLE INFORMATION Test Vehicle: 15,000 Ib. Truck Test No.: P Test Program: RSA Bollards with 5 in. Footing Test Date: 4/4/05 Make Model Body Style VIN Color Odometer Reading Transmission Final Drive TEST VEHICLE INFORMATION International Cylinders S1900 Engine Displ. (L) Truck Engine Placement 1HTLOMJP4HH Fuel Type White No. of Axles Disc Brakes, Front Manual Disc Brakes, Rear Rear Anti-lock Brakes 6 Unknown Longitudinal Diesel 2 No No No Manufactured By Date of Manufacture DATA FROM CERTIFICATION LABEL Navistar International Transportation Corp. May-87 GVWR (lbs) GAWR Front (lbs) GAWR Rear (lbs) Unknown Unknown Unknown DATA FROM TIRE PLACARD Measured Parameter Front Rear Max. Tire Pressure (psi) Unknown Unknown Cold Pressure (psi) Unknown Unknown Recommend Tire Size Unknown Unknown Actual Tire Size on Vehicle Unknown Unknown Actual Tire Manufacturer Unknown Unknown VEHICLE WEIGHTS As Received (lbs) As Tested (lbs) Front Rear Total Front Rear Total Left Right Totals Ratio(%) 55% 45% 100% 46% 54% 100% 6

12 DATA SHEET NO. 2 TEST VEHICLE GEOMETRY Test Vehicle: 15,000 Ib. Truck Test No.: P Test Program: RSA Bollards with 5 in. Footing Test Date: 4/4/05 TEST VEHICLE GEOMETRY (mm) A 780 D 3503 G 650 K 2250 B 500 E 2927 I 590 L 2050 C 800 F 1878 J 1050 N

13 DATA SHEET NO. 3 EVALUATION OF TEST RESULTS Test Vehicle: 15,000 Ib. Truck Test No.: P Test Program: RSA Bollards with 5 in. Footing Test Date: 4/4/05 CRASH TEST ASSESSMENT PASS FAIL Penetration of the Front Edge of the Cargo Bed Limited to One Meter Beyond the Pre-Impact, Inside Edge of the Barrier. Comments: Vehicle was completely arrested by the bollard system. x 8

14 DATA SHEET NO. 4 - VEHICLE ACCELEROMETER DATA SUMMARY Test Vehicle: 15,000 lb Truck Project No.: P Test Program: RSA Bollards with 5 in. Footing Test Date: 4/4/05 VEHICLE ACCELEROMETER PEAK DATA Vehicle Location Axis Units Max Time Min Time Vehicle Rear Frame Rail X X G's Vehicle Rear Frame Rail Y Y G's Vehicle Rear Frame Rail Z Z G's Vehicle Rear Frame Res. N/A G's

15 DATA SHEET NO. 5 CAMERA VIEWS & FILM SPEEDS Test Vehicle: 15,000 Ib. Truck Test No.: P Test Program: RSA Bollards with 5 in. Footing Test Date: 4/4/05 No. Camera View Location (mm) X Y Z Angle (Deg.) Film Plane to Head Lens (mm) Speed (fps) 1 Real Time (Panning) N/A N/A 30 2 Real Time (Driver's Side) N/A N/A 30 3 Real Time (Left Front 3/ N/A N/A 30 4 High Speed Digital Color (Driver's Side) N/A 50 mm High Speed Digital Color (Overhead) N/A 24 mm High Speed Digital Color (Left Front 3/4) N/A 85 mm High Speed Digital Color (Front) N/A All camera measurements were made relative to the point of impact. 10

16 APPENDIX A PHOTOGRAPHS A

17 FIGURE 1. Test Article as Received FIGURE 2. Right Front View at Test Article A-1

18 FIGURE 3. Anti-Ram Bollard 5 Inch Footing FIGURE 4. Bollard 10 Inch Diameter and 1 inch Wall Thickness A-2

19 FIGURE 5. Bollard Foundation Module Front View and Re-bar FIGURE 6. Bollard Foundation Module Rear View A-3

20 FIGURE 7. Excavation FIGURE 8. Embedment Depth A-4

21 FIGURE 9. Test Article Positioned in Place FIGURE 10. Test Article During Installation A-5

22 FIGURE 11. Test Article During Installation FIGURE 12. Test Article During Installation A-6

23 FIGURE 13. Test Article Left Side View FIGURE 14. Test Article Left Front ¾ View A-7

24 FIGURE 15. Test Article Front View FIGURE 16. Test Set-Up A-8

25 FIGURE 17. Test Set-Up FIGURE 18. Test Set-Up A-9

26 FIGURE 19. Test Set-Up FIGURE 20. Test Set-Up A-10

27 FIGURE 21. Test Set-Up FIGURE 22. Test Set-Up A-11

28 FIGURE 23. Test Article Orientation to Front Bumper FIGURE 24. Test Article Orientation to Front Bumper A-12

29 FIGURE 25. Test Set-Up FIGURE 26. Ballast A-13

30 FIGURE 27. Post-Test Left Side View FIGURE 28. Post-Test Left Side View Close-Up A-14

31 FIGURE 29. Post-Test Front View FIGURE 30. Post-Test Overhead View A-15

32 FIGURE 31. Post-Test Test Article Front View FIGURE 32. Post-Test Test Article Left Side View A-16

33 FIGURE 33. Post-Test Test Article Left Side View FIGURE 34. Center Bollard Deflection A-17

34 FIGURE 35. Ballast FIGURE 36. Action Sequence 1 A-18

35 FIGURE 37. Action Sequence 2 FIGURE 38. Action Sequence 3 A-19

36 FIGURE 39. Action Sequence 4 A-20

37 APPENDIX B DATA PLOTS B

38 Test Vehicle: 15,000 lb Truck Test Date: 4/4/05 Test Program: RSA Bollards with 5 in. Footing Project No.: P G's Time - Milliseconds Curve Description Vehicle Rear Frame Rail X CURNO Type SAE Class Units 001 FIL 60 G's Max Time Min Time G's Time - Milliseconds Curve Description Vehicle Rear Frame Rail Y CURNO Type SAE Class Units 002 FIL 60 G's Max Time Min Time G's Time - Milliseconds Curve Description Vehicle Rear Frame Rail Z CURNO Type SAE Class Units 003 FIL 60 G's Max Time Min Time G's Time - Milliseconds Curve Description Vehicle Rear Frame Rail Resultant CURNO Type SAE Class Units 001 RES 60 G's Max Time Min Time B-1

39 Test Vehicle: 15,000 lb Truck Test Date: 4/4/05 Test Program: RSA Bollards with 5 in. Footing Project No.: P MPH Time - Milliseconds Curve Description Vehicle Rear Frame Rail X Velocity CURNO Type SAE Class Units 001 IN1 180 MPH Max Time Min Time Inches Time - Milliseconds Curve Description Vehicle Rear Frame Rail X Displacement CURNO Type SAE Class Units 001 IN2 180 Inches Max Time Min Time B-2

40 APPENDIX C INSTRUMENTATION LIST C

41 RSA Bollards with 5 in. Footing Instrumentation Data Channel Assignments 4/4/05 15,000 lb Truck CH. LOCATION AXIS IDENT. NO. DESCRIPTION MFR MODEL UNITS 1 Rear Frame Rail X MDASX Accel., Vehicle block I.C.Sensor G 2 Rear Frame Rail Y MDASY Accel., Vehicle block I.C. Sensor G 3 Rear Frame Rail Z MDASZ Accel., Vehicle block I.C. Sensor G C-1

42 APPENDIX D MANUFACTURERS DRAWINGS D

CRASH TEST REPORT FOR PERIMETER BARRIERS AND GATES TESTED TO SD-STD-02.01, REVISION A, MARCH Anti-Ram Bollards

CRASH TEST REPORT FOR PERIMETER BARRIERS AND GATES TESTED TO SD-STD-02.01, REVISION A, MARCH Anti-Ram Bollards CRASH TEST REPORT FOR PERIMETER BARRIERS AND GATES TESTED TO SD-STD-02.01, REVISION A, MARCH 2003 Anti-Ram Bollards Prepared for: RSA Protective Technologies, LLC 1573 Mimosa Court Upland, CA 91784 Test

More information

RSA Protective Technologies

RSA Protective Technologies TEST REPORT FOR: RSA Protective Technologies K12 Surface Mounted Bollard System TESTED TO: ASTM F 2656-07 Standard Test Method for Vehicle Crash Testing of Perimeter Barriers Test M50 PREPARED FOR: Battelle

More information

FAAC International, Inc.

FAAC International, Inc. TEST REPORT FOR: FAAC International, Inc. J 355 HA M30 (K4) Bollard TESTED TO: ASTM F 2656-07 Standard Test Method for Vehicle Crash Testing of Perimeter Barriers Test M30 PREPARED FOR: FAAC International,

More information

Virginia Department of Transportation

Virginia Department of Transportation TEST REPORT FOR: Virginia Department of Transportation SKT SP 350 50 (15.24 m) System PREPARED FOR: Virginia Department of Transportation 1401 E. Broad St. Richmond, VA 23219 TEST REPORT NUMBER: REPORT

More information

CRASH TESTING OF RSA/K&C ANTI-RAM FOUNDATION BOLLARD PAD IN ACCORDANCE WITH U.S. DEPARTMENT OF STATE DIPLOMATIC SECURITY SD-STD-02.

CRASH TESTING OF RSA/K&C ANTI-RAM FOUNDATION BOLLARD PAD IN ACCORDANCE WITH U.S. DEPARTMENT OF STATE DIPLOMATIC SECURITY SD-STD-02. CRASH TESTING OF RSA/K&C ANTI-RAM FOUNDATION BOLLARD PAD IN ACCORDANCE WITH U.S. DEPARTMENT OF STATE DIPLOMATIC SECURITY SD-STD-02.01 REVISION A Prepared for RSA Protective Technologies, LLC FINAL REPORT

More information

The Center for Auto Safety

The Center for Auto Safety TEST REPORT FOR: The Center for Auto Safety 50 mph Vehicle to Vehicle 30% Offset Rear Impact 50 mph Vehicle to Vehicle 30% Offset Rear Impact 1999 Jeep Grand Cherokee Laredo 1987 Ford Taurus PREPARED FOR:

More information

The Center for Auto Safety

The Center for Auto Safety TEST REPORT FOR: The Center for Auto Safety 40 mph Vehicle to Vehicle 30% Offset Rear Impact 40 mph Vehicle to Vehicle 30% Offset Rear Impact 1996 Jeep Grand Cherokee Limited 1988 Ford Taurus PREPARED

More information

COMPLIANCE TESTING FOR FMVSS 207 SEATING SYSTEMS

COMPLIANCE TESTING FOR FMVSS 207 SEATING SYSTEMS REPORT NO. COMPLIANCE TESTING FOR FMVSS 207 SEATING SYSTEMS 2008 CHEVROLET IMPALA 4-DOOR NHTSA NO.C80102 PREPARED BY: KARCO ENGINEERING, LLC 9270 HOLLY ROAD ADELANTO, CALIFORNIA 92301 September 24, 2008

More information

REPORT NO. TR-P NC SAFETY COMPLIANCE TESTING FOR FMVSS 223 REAR IMPACT GUARDS 2007 TRANSFREIGHT TECHNOLOGY NHTSA NO.

REPORT NO. TR-P NC SAFETY COMPLIANCE TESTING FOR FMVSS 223 REAR IMPACT GUARDS 2007 TRANSFREIGHT TECHNOLOGY NHTSA NO. REPORT NO. SAFETY COMPLIANCE TESTING FOR FMVSS 223 REAR IMPACT GUARDS 2007 TRANSFREIGHT TECHNOLOGY NHTSA NO. RIG 009 PREPARED BY: KARCO ENGINEERING, LLC. 9270 HOLLY ROAD ADELANTO, CALIFORNIA 92301 SEPTEMBER

More information

REPORT NUMBER TR-P NC SAFETY COMPLIANCE TESTING FOR FMVSS 124 ACCELERATOR CONTROL SYSTEMS

REPORT NUMBER TR-P NC SAFETY COMPLIANCE TESTING FOR FMVSS 124 ACCELERATOR CONTROL SYSTEMS REPORT NUMBER TR-P299-3-NC SAFETY COMPLIANCE TESTING FOR FMVSS 124 ACCELERATOR CONTROL SYSTEMS NISSAN MOTOR CORPORATION 29 NISSAN ROGUE 5-DOOR MPV NHTSA NUMBER: C95 PREPARED BY: KARCO ENGINEERING, LLC.

More information

ASTM F TEST M30 ON THE RSS-3000 DROP BEAM SYSTEM

ASTM F TEST M30 ON THE RSS-3000 DROP BEAM SYSTEM Proving Ground Test Report No.: 510602-RSS3 Test Report Date: January 2014 ASTM F2656-07 TEST M30 ON THE RSS-3000 DROP BEAM SYSTEM by Dean C. Alberson, Ph.D., P.E. Research Engineer Michael S. Brackin,

More information

REPORT NUMBER: 301-MGA SAFETY COMPLIANCE TESTING FOR FMVSS 301R FUEL SYSTEM INTEGRITY REAR IMPACT

REPORT NUMBER: 301-MGA SAFETY COMPLIANCE TESTING FOR FMVSS 301R FUEL SYSTEM INTEGRITY REAR IMPACT REPORT NUMBER: 301-MGA-2007-002 SAFETY COMPLIANCE TESTING FOR FMVSS 301R FUEL SYSTEM INTEGRITY REAR IMPACT NISSAN MOTOR CO., LTD. 2006 NISSAN PATHFINDER LE 4X2 NHTSA NUMBER: C65200 PREPARED BY: MGA RESEARCH

More information

REPORT NUMBER: 301-CAL SAFETY COMPLIANCE TESTING FOR FMVSS 301 FUEL SYSTEM INTEGRITY REAR IMPACT FORD MOTOR COMPANY 2009 FORD F150 2-DOOR PICKUP

REPORT NUMBER: 301-CAL SAFETY COMPLIANCE TESTING FOR FMVSS 301 FUEL SYSTEM INTEGRITY REAR IMPACT FORD MOTOR COMPANY 2009 FORD F150 2-DOOR PICKUP REPORT NUMBER: 301-CAL-09-03 SAFETY COMPLIANCE TESTING FOR FMVSS 301 FUEL SYSTEM INTEGRITY REAR IMPACT FORD MOTOR COMPANY 2009 FORD F150 2-DOOR PICKUP NHTSA NUMBER: C90206 CALSPAN TRANSPORTATION SCIENCES

More information

REPORT NUMBER: 301-MGA SAFETY COMPLIANCE TESTING FOR FMVSS 301R FUEL SYSTEM INTEGRITY REAR IMPACT

REPORT NUMBER: 301-MGA SAFETY COMPLIANCE TESTING FOR FMVSS 301R FUEL SYSTEM INTEGRITY REAR IMPACT REPORT NUMBER: 301-MGA-2011-008 SAFETY COMPLIANCE TESTING FOR FMVSS 301R FUEL SYSTEM INTEGRITY REAR IMPACT MAZDA MOTOR CORPORATION 2011 MAZDA 2 SPORT MT NHTSA NUMBER: CB5400 PREPARED BY: MGA RESEARCH CORPORATION

More information

REPORT NUMBER: 301-CAL SAFETY COMPLIANCE TESTING FOR FMVSS 301 FUEL SYSTEM INTEGRITY HONDA MOTOR COMPANY 2007 HONDA ACCORD 4-DOOR SEDAN

REPORT NUMBER: 301-CAL SAFETY COMPLIANCE TESTING FOR FMVSS 301 FUEL SYSTEM INTEGRITY HONDA MOTOR COMPANY 2007 HONDA ACCORD 4-DOOR SEDAN REPORT NUMBER: 301-CAL-07-05 SAFETY COMPLIANCE TESTING FOR FMVSS 301 FUEL SYSTEM INTEGRITY HONDA MOTOR COMPANY 2007 HONDA ACCORD 4-DOOR SEDAN NHTSA NUMBER: C75304 CALSPAN TEST NUMBER: 8832-F301-05 CALSPAN

More information

REPORT NUMBER: 301-MGA SAFETY COMPLIANCE TESTING FOR FMVSS 301R FUEL SYSTEM INTEGRITY REAR IMPACT

REPORT NUMBER: 301-MGA SAFETY COMPLIANCE TESTING FOR FMVSS 301R FUEL SYSTEM INTEGRITY REAR IMPACT REPORT NUMBER: 301-MGA-2010-007 SAFETY COMPLIANCE TESTING FOR FMVSS 301R FUEL SYSTEM INTEGRITY REAR IMPACT NISSAN MOTOR COMPANY LTD 2010 NISSAN CUBE NHTSA NUMBER: CA5205 PREPARED BY: MGA RESEARCH CORPORATION

More information

REPORT NUMBER: 301-CAL SAFETY COMPLIANCE TESTING FOR FMVSS 301 FUEL SYSTEM INTEGRITY REAR IMPACT

REPORT NUMBER: 301-CAL SAFETY COMPLIANCE TESTING FOR FMVSS 301 FUEL SYSTEM INTEGRITY REAR IMPACT REPORT NUMBER: 301-CAL-09-01 SAFETY COMPLIANCE TESTING FOR FMVSS 301 FUEL SYSTEM INTEGRITY REAR IMPACT HYUNDAI MOTOR COMPANY 2009 HYUNDAI ACCENT 4-DOOR SEDAN NHTSA NUMBER: C90503 CALSPAN TRANSPORTATION

More information

REPORT NUMBER: 301-MGA SAFETY COMPLIANCE TESTING FOR FMVSS 301R FUEL SYSTEM INTEGRITY REAR IMPACT

REPORT NUMBER: 301-MGA SAFETY COMPLIANCE TESTING FOR FMVSS 301R FUEL SYSTEM INTEGRITY REAR IMPACT REPORT NUMBER: 301-MGA-2010-005 SAFETY COMPLIANCE TESTING FOR FMVSS 301R FUEL SYSTEM INTEGRITY REAR IMPACT NISSAN MOTOR COMPANY LTD 2010 NISSAN CUBE NHTSA NUMBER: CA5201 PREPARED BY: MGA RESEARCH CORPORATION

More information

REPORT NUMBER: 301-CAL SAFETY COMPLIANCE TESTING FOR FMVSS 301 FUEL SYSTEM INTEGRITY REAR IMPACT MAZDA MOTOR CORPORATION 2008 MAZDA CX-9 SUV

REPORT NUMBER: 301-CAL SAFETY COMPLIANCE TESTING FOR FMVSS 301 FUEL SYSTEM INTEGRITY REAR IMPACT MAZDA MOTOR CORPORATION 2008 MAZDA CX-9 SUV REPORT NUMBER: 301-CAL-08-03 SAFETY COMPLIANCE TESTING FOR FMVSS 301 FUEL SYSTEM INTEGRITY REAR IMPACT MAZDA MOTOR CORPORATION 2008 MAZDA CX-9 SUV NHTSA NUMBER: C85401 CALSPAN TRANSPORTATION SCIENCES CENTER

More information

REPORT NUMBER TR-P NC SAFETY COMPLIANCE TESTING FOR FMVSS 124 ACCELERATOR CONTROL SYSTEMS CHRYSLER LLC 2009 DODGE JOURNEY 5-DOOR MPV

REPORT NUMBER TR-P NC SAFETY COMPLIANCE TESTING FOR FMVSS 124 ACCELERATOR CONTROL SYSTEMS CHRYSLER LLC 2009 DODGE JOURNEY 5-DOOR MPV REPORT NUMBER TR-P29009-02-NC SAFETY COMPLIANCE TESTING FOR FMVSS 124 ACCELERATOR CONTROL SYSTEMS CHRYSLER LLC 2009 DODGE JOURNEY 5-DOOR MPV NHTSA NUMBER: C90302 PREPARED BY: KARCO ENGINEERING, LLC. 9270

More information

SAFETY COMPLIANCE TESTING FOR FMVSS 111. REARVIEW MIRRORS (Other Than School Buses)

SAFETY COMPLIANCE TESTING FOR FMVSS 111. REARVIEW MIRRORS (Other Than School Buses) REPORT NO. 111-KAR-10-001 SAFETY COMPLIANCE TESTING FOR FMVSS 111 REARVIEW MIRRORS (Other Than School Buses) 2010 FORD TAURUS 4-DOOR SEDAN NHTSA NO: CA0211 PREPARED BY: KARCO ENGINEERING LLC. 9270 HOLLY

More information

SAFETY COMPLIANCE TESTING FOR FMVSS 111. REARVIEW MIRRORS (Other Than School Buses)

SAFETY COMPLIANCE TESTING FOR FMVSS 111. REARVIEW MIRRORS (Other Than School Buses) REPORT NO. 111-KAR-08-003 SAFETY COMPLIANCE TESTING FOR FMVSS 111 REARVIEW MIRRORS (Other Than School Buses) 2008 DODGE GRAND CARAVAN SE 5-DOOR MPV NHTSA NO: C80305 PREPARED BY: KARCO ENGINEERING LLC.

More information

Manual for Assessing Safety Hardware

Manual for Assessing Safety Hardware American Association of State Highway and Transportation Officials Manual for Assessing Safety Hardware 2009 vii PREFACE Effective traffic barrier systems, end treatments, crash cushions, breakaway devices,

More information

CLASSIFICATION NOTES. Type Testing Procedure for. Crankcase Explosion Relief Valves

CLASSIFICATION NOTES. Type Testing Procedure for. Crankcase Explosion Relief Valves CLASSIFICATION NOTES Type Testing Procedure for Crankcase Explosion Relief Valves Contents 1. Scope, Application 2. Recognized Standards 3. Purpose 4. Test Facilities 5. Explosion Test Process 6. Testing

More information

EXPERIMENTAL TEST OF OCCUPANT ENTRAPMENT FORD TAURUS INTO REAR OF FORD EXPLORER 30% OFFSET, 70 MPH. Test Date: August 3, 2010

EXPERIMENTAL TEST OF OCCUPANT ENTRAPMENT FORD TAURUS INTO REAR OF FORD EXPLORER 30% OFFSET, 70 MPH. Test Date: August 3, 2010 EXPERIMENTAL TEST OF OCCUPANT ENTRAPMENT FORD TAURUS INTO REAR OF FORD EXPLORER 30% OFFSET, 70 MPH Test Date: August 3, 2010 Final Report Date: September 25, 2010 SECTION 1 PURPOSE AND SUMMARY OF TEST

More information

SAFETY COMPLIANCE TESTING FOR FMVSS 111. REARVIEW MIRRORS (Other Than School Buses)

SAFETY COMPLIANCE TESTING FOR FMVSS 111. REARVIEW MIRRORS (Other Than School Buses) REPORT NO. 111-KAR-08-001 SAFETY COMPLIANCE TESTING FOR FMVSS 111 REARVIEW MIRRORS (Other Than School Buses) 2008 CHRYSLER 300 4-DOOR SEDAN NHTSA NO: C80307 PREPARED BY: KARCO ENGINEERING LLC. 9270 HOLLY

More information

SAFETY COMPLIANCE TESTING FOR FMVSS 225 Child Restraint Anchorage Systems

SAFETY COMPLIANCE TESTING FOR FMVSS 225 Child Restraint Anchorage Systems FINAL REPORT NUMBER 225-MGA-10-003 SAFETY COMPLIANCE TESTING FOR FMVSS 225 NISSAN MOTORS 2010 NISSAN ROGUE NHTSA No. CA5202 MGA RESEARCH CORPORATION 446 Executive Drive Troy, Michigan 48083 Test Date:

More information

JRS Dynamic Rollover Test Toyota Prius

JRS Dynamic Rollover Test Toyota Prius Page 1 of 62 JRS Dynamic Rollover Test 2010 Toyota Prius Sponsored By: Automotive Safety Research Institute Charlottesville, VA. Vehicle Donated by: State Farm Insurance Company Chicago, IL. Introduction

More information

SAFETY COMPLIANCE TESTING FOR FMVSS 225 Child Restraint Anchorage Systems

SAFETY COMPLIANCE TESTING FOR FMVSS 225 Child Restraint Anchorage Systems FINAL REPORT NUMBER 225-MGA-06-002 SAFETY COMPLIANCE TESTING FOR FMVSS 225 GENERAL MOTORS CORPORATION 2006 HUMMER H3 NHTSA No. C60102 MGA RESEARCH CORPORATION 446 Executive Drive Troy, Michigan 48083 Test

More information

JRS Dynamic Rollover Test Chevrolet Malibu

JRS Dynamic Rollover Test Chevrolet Malibu Page 1 of 61 JRS Dynamic Rollover Test 2009 Chevrolet Malibu Sponsored By: Automotive Safety Research Institute Charlottesville, VA. Vehicle Donated by: State Farm Insurance Company Chicago, IL. Introduction

More information

TEST REPORT FOR: The Tracy Law Firm Honda Fit 5-Door Hatchback TESTED TO: 64.4 km/h 40% Moderate Overlap Frontal Impact PREPARED FOR:

TEST REPORT FOR: The Tracy Law Firm Honda Fit 5-Door Hatchback TESTED TO: 64.4 km/h 40% Moderate Overlap Frontal Impact PREPARED FOR: TEST REPORT FOR: The Tracy Law Firm 213 Honda Fit 5-Door Hatchback TESTED TO: 64.4 km/h 4% Moderate Overlap Frontal Impact PREPARED FOR: The Tracy Law Firm 471 Benal St. Dallas, TX 75235 TEST REPORT NUMBER:

More information

SAFETY COMPLIANCE TESTING FOR FMVSS 202a Head Restraints

SAFETY COMPLIANCE TESTING FOR FMVSS 202a Head Restraints FINAL REPORT NUMBER 202a-MGA-10-003 SAFETY COMPLIANCE TESTING FOR FMVSS 202a FORD MOTOR COMPANY 2010 Lincoln MKT MPV NHTSA No. CA0213 MGA RESEARCH CORPORATION 446 Executive Drive Troy, Michigan 48083 Test

More information

JRS Dynamic Rollover Test Toyota Camry

JRS Dynamic Rollover Test Toyota Camry Page 1 of 60 JRS Dynamic Rollover Test 2007 Toyota Camry Hybrid Version Sponsored By: Automotive Safety Research Institute Charlottesville, VA. Introduction Page 2 of 60 Center for Injury Research conducted

More information

STI Project: Barrier Systems, Inc. RTS-QMB Longitudinal Barrier. Page 38 of 40 QBOR1. Appendix F (Continued) Figure F-3

STI Project: Barrier Systems, Inc. RTS-QMB Longitudinal Barrier. Page 38 of 40 QBOR1. Appendix F (Continued) Figure F-3 Barrier Systems, Inc. RTS-QMB Longitudinal Barrier STI Project: QBOR1 Page 38 of 40 Appendix F (Continued) Figure F-3 t=.500sec 115 meters overall 37.1 Impact Severity (kj).. 141.6 Angle (deg).. 25 Speed

More information

ROBUST PROJECT Norwegian Public Roads Administration / Force Technology Norway AS

ROBUST PROJECT Norwegian Public Roads Administration / Force Technology Norway AS ROBUST PROJECT Norwegian Public Roads Administration / Force Technology Norway AS Evaluation of small car - RM_R1 - prepared by Politecnico di Milano Volume 1 of 1 January 2006 Doc. No.: ROBUST-5-002/TR-2004-0039

More information

Pedestrian Autonomous Emergency Braking Test Protocol (Version II) February 2019

Pedestrian Autonomous Emergency Braking Test Protocol (Version II) February 2019 Pedestrian Autonomous Emergency Braking Test Protocol (Version II) February 2019 Contents DOCUMENT REVISION HISTORY... ii SUMMARY... 1 TEST ENVIRONMENT... 2 Surface and Markings... 2 Surroundings... 2

More information

Occupant Restraint Systems in Frontal Impact

Occupant Restraint Systems in Frontal Impact TEST METHOD 208 Occupant Restraint Systems in Frontal Impact Revised: Issued: December 1996R January 20, 1976 (Ce document est aussi disponible en français) Table of Contents 1. Introduction... 1 2. General

More information

SAFETY COMPLIANCE TESTING FOR FMVSS 225 Child Restraint Anchorage Systems

SAFETY COMPLIANCE TESTING FOR FMVSS 225 Child Restraint Anchorage Systems FINAL REPORT NUMBER 225-MGA-06-007 SAFETY COMPLIANCE TESTING FOR FMVSS 225 TOYOTA MOTOR CORPORATION 2006 TOYOTA HIGHLANDER NHTSA No. C65101 MGA RESEARCH CORPORATION 446 Executive Drive Troy, Michigan 48083

More information

VERIFICATION & VALIDATION REPORT of MGS Barrier Impact with 1100C Vehicle Using Toyota Yaris Coarse FE Model

VERIFICATION & VALIDATION REPORT of MGS Barrier Impact with 1100C Vehicle Using Toyota Yaris Coarse FE Model VERIFICATION & VALIDATION REPORT of MGS Barrier Impact with 1100C Vehicle Using Toyota Yaris Coarse FE Model CCSA VALIDATION/VERIFICATION REPORT Page 1 of 4 Project: CCSA Longitudinal Barriers on Curved,

More information

JRS Dynamic Rollover Test Scion xb

JRS Dynamic Rollover Test Scion xb Page 1 of 57 JRS Dynamic Rollover Test 2008 Scion xb Sponsored By: Automotive Safety Research Institute Charlottesville, VA. Introduction Page 2 of 57 Center for Injury Research conducted a JRS dynamic

More information

SPCT Method. The SPCT Method - Testing of Dog Crates. Utskrivet dokument är ostyrt, dvs inte säkert gällande.

SPCT Method. The SPCT Method - Testing of Dog Crates. Utskrivet dokument är ostyrt, dvs inte säkert gällande. Kvalitetsdokument Författare, enhet Mikael Videby Bygg och Mekanik Hållfasthet och konstruktion Utgåva 1 (7) Godkännare 2 The Testing of Dog Crates Application Area... 2 References... 2 1 Test Sample Selection...

More information

SAFETY COMPLIANCE TESTING FOR FMVSS 201 Occupant Protection In Interior Impact Upper Interior Head Impact Protection

SAFETY COMPLIANCE TESTING FOR FMVSS 201 Occupant Protection In Interior Impact Upper Interior Head Impact Protection FINAL REPORT NUMBER 201UI-MGA-10-01 SAFETY COMPLIANCE TESTING FOR FMVSS 201 Occupant Protection In Interior Impact Upper Interior Head Impact Protection CAMI AUTOMOTIVE, INC. 2010 Chevrolet Equinox MPV

More information

REPORT NUMBER: NCAP305I-MGA NEW CAR ASSESSMENT PROGRAM (NCAP) FMVSS No. 305 Indicant Test

REPORT NUMBER: NCAP305I-MGA NEW CAR ASSESSMENT PROGRAM (NCAP) FMVSS No. 305 Indicant Test REPORT NUMBER: NCAP305I-MGA-2012-008 NEW CAR ASSESSMENT PROGRAM (NCAP) FMVSS No. 305 Indicant Test GENERAL MOTORS LLC 2013 Chevrolet Malibu ECO4-Dr Hybrid Sedan NHTSA NUMBER: MD0101 MGA RESEARCH CORPORATION

More information

Fuel System Integrity

Fuel System Integrity TECHNICAL STANDARDS DOCUMENT No. 301, Revision 2R Fuel System Integrity The text of this document is based on Federal Motor Vehicle Safety Standard No. 301, Fuel System Integrity, as published in the U.S.

More information

Pedestrian Autonomous Emergency Braking Test Protocol (Version 1) December 2018

Pedestrian Autonomous Emergency Braking Test Protocol (Version 1) December 2018 Pedestrian Autonomous Emergency Braking Test Protocol (Version 1) December 2018 Contents DOCUMENT REVISION HISTORY... ii SUMMARY... 1 TEST ENVIRONMENT... 1 Surface and Markings... 1 Surroundings... 2 Ambient

More information

State Scientific Center of the Russian Federation for Motor Vehicles. Protocol No. 1003/UO/MMB/W/94-12

State Scientific Center of the Russian Federation for Motor Vehicles. Protocol No. 1003/UO/MMB/W/94-12 State Scientific Center of the Russian Federation for Motor Vehicles Research Center for Testing and Refining Automotive Vehicles (NICIAMT) Technical certification service -NAMI- Avtopolygon, Dmitrovski

More information

Draft for comments only Not to be cited as East African Standard

Draft for comments only Not to be cited as East African Standard EAST AFRICAN STANDARD CD/K/021:2008 ICS 43.040.50 Motor vehicle safety Steering mechanism of motor vehicles (Category M 1 only) Behaviour on impact EAST AFRICAN COMMUNITY EAC 2010 First Edition 2010 CD/K/021:2008

More information

Texas Transportation Institute The Texas A&M University System College Station, Texas

Texas Transportation Institute The Texas A&M University System College Station, Texas 1. Report No. FHWA/TX-05/9-8132-P7 4. Title and Subtitle TL-4 CRASH TESTING OF THE F411 BRIDGE RAIL 2. Government Accession No. 3. Recipient's Catalog No. 5. Report Date October 2004 Technical Report Documentation

More information

TEST METHODS CONCERNING TRANSPORT EQUIPMENT

TEST METHODS CONCERNING TRANSPORT EQUIPMENT PART IV TEST METHODS CONCERNING TRANSPORT EQUIPMENT - 403 - CONTENTS OF PART IV Section Page 40. INTRODUCTION TO PART IV... 407 40.1 PURPOSE... 407 40.2 SCOPE... 407 41. DYNAMIC LONGITUDINAL IMPACT TEST

More information

CNG Fuel System Integrity

CNG Fuel System Integrity TEST METHOD 301.2 CNG Fuel System Integrity Revised: Issued: February 28, 2004R May 20, 1994 (Ce document est aussi disponible en français) Table of Content 1. Introduction... 1 2. Definition... 1 3. Test

More information

July 10, Refer to: HSA-10/CC-78A

July 10, Refer to: HSA-10/CC-78A July 10, 2003 Refer to: HSA-10/CC-78A Barry D. Stephens, P.E. Senior Vice President of Engineering ENERGY ABSORPTION Systems, Inc. 3617 Cincinnati Avenue Rocklin, California 95765 Dear Mr. Stephens: Your

More information

GENERAL TESTING LABORATORIES, INC LEEDSTOWN ROAD COLONIAL BEACH, VIRGINIA 22443

GENERAL TESTING LABORATORIES, INC LEEDSTOWN ROAD COLONIAL BEACH, VIRGINIA 22443 REPORT NUMBER 202a-GTL-10-004 SAFETY COMPLIANCE TESTING FOR S HEAD RESTRAINTS STATIC REQUIREMENTS VOLVO CAR CORPORATION 2010 VOLVO S40, PASSENGER CAR NHTSA NO. CA5900 GENERAL TESTING LABORATORIES, INC.

More information

REPORT NUMBER: 120-MGA

REPORT NUMBER: 120-MGA REPORT NUMBER: 120-MGA-2011-004 SAFETY COMPLIANCE TESTING FOR FMVSS NO. 120 TIRE SELECTION AND RIMS FOR MOTOR VEHICLES WITH A GVWR OF MORE THAN 4,536 kg STARTRANS 2010 MFSAB NHTSA NO.: CA0900 PREPARED

More information

Low-Speed Crash Test Protocol (Version V) May 2002

Low-Speed Crash Test Protocol (Version V) May 2002 Low-Speed Crash Test Protocol (Version V) May 2002 Insurance Institute for Highway Safety Low-Speed Crash Test Protocol (Version V) Low-Speed Test Configurations Four different low-speed crash tests, at

More information

TRANSPORT OF DANGEROUS GOODS

TRANSPORT OF DANGEROUS GOODS Recommendations on the TRANSPORT OF DANGEROUS GOODS Manual of Tests and Criteria Fifth revised edition Amendment 1 UNITED NATIONS SECTION 38 38.3 Amend to read as follows: "38.3 Lithium metal and lithium

More information

5. STRUCTURAL INTEGRITY 5.1 STRUCTURAL STRENGTH AND DISTORTION TESTS - STRUCTURAL SHAKEDOWN TEST 5.1-I. DISCUSSION

5. STRUCTURAL INTEGRITY 5.1 STRUCTURAL STRENGTH AND DISTORTION TESTS - STRUCTURAL SHAKEDOWN TEST 5.1-I. DISCUSSION 5. STRUCTURAL INTEGRITY 5.1 STRUCTURAL STRENGTH AND DISTORTION TESTS - STRUCTURAL SHAKEDOWN TEST 5.1-I. DISCUSSION The objective of this test is to determine certain static characteristics (e.g., bus floor

More information

REPORT NUMBER: 214P-MGA SAFETY COMPLIANCE TESTING FOR FMVSS 214 DYNAMIC SIDE IMPACT PROTECTION RIGID POLE

REPORT NUMBER: 214P-MGA SAFETY COMPLIANCE TESTING FOR FMVSS 214 DYNAMIC SIDE IMPACT PROTECTION RIGID POLE REPORT NUMBER: 214P-MGA-21-3 SAFETY COMPLIANCE TESTING FOR FMVSS 214 DYNAMIC SIDE IMPACT PROTECTION RIGID POLE FORD MOTOR COMPANY 21 FORD F-15 4x2 REGULAR CAB NHTSA NUMBER: CA28 PREPARED BY: MGA RESEARCH

More information

REPORT NUMBER: 131-MGA SAFETY COMPLIANCE TESTING FOR FMVSS NO. 131 SCHOOL BUS PEDESTRIAN SAFETY DEVICES

REPORT NUMBER: 131-MGA SAFETY COMPLIANCE TESTING FOR FMVSS NO. 131 SCHOOL BUS PEDESTRIAN SAFETY DEVICES REPORT NUMBER: 131-MGA-05-001 SAFETY COMPLIANCE TESTING FOR FMVSS NO. 131 SCHOOL BUS PEDESTRIAN SAFETY DEVICES Les Entreprises Michel Corbeil Inc. 2004 Corbeil 30 Passenger School Bus NHTSA No. C40902

More information

MASH Test 3-11 on the T131RC Bridge Rail

MASH Test 3-11 on the T131RC Bridge Rail TTI: 9-1002-12 MASH Test 3-11 on the T131RC Bridge Rail ISO 17025 Laboratory Testing Certificate # 2821.01 Crash testing performed at: TTI Proving Ground 3100 SH 47, Building 7091 Bryan, TX 77807 Test

More information

REPORT NUMBER: 120-MGA

REPORT NUMBER: 120-MGA REPORT NUMBER: 120-MGA-2011-001 SAFETY COMPLIANCE TESTING FOR FMVSS NO. 120 TIRE SELECTION AND RIMS FOR MOTOR VEHICLES WITH A GVWR OF MORE THAN 4,536 kg FOREST RIVER, INC. / STARCRAFT DIVISION 2011 STARCRAFT

More information

ISO 8855 INTERNATIONAL STANDARD. Road vehicles Vehicle dynamics and road-holding ability Vocabulary

ISO 8855 INTERNATIONAL STANDARD. Road vehicles Vehicle dynamics and road-holding ability Vocabulary INTERNATIONAL STANDARD ISO 8855 Second edition 2011-12-15 Road vehicles Vehicle dynamics and road-holding ability Vocabulary Véhicules routiers Dynamique des véhicules et tenue de route Vocabulaire Reference

More information

Active Bollards An aesthetic solution to a complex need

Active Bollards An aesthetic solution to a complex need Active Bollards An aesthetic solution to a complex need Crash tested, Ross active bollards are designed to provide temporary or permanent security measures and are built to withstand violent impacts. Despite

More information

Reduced Stopping Distance: Why the Mandate?

Reduced Stopping Distance: Why the Mandate? Reduced Stopping Distance: Why the Mandate? According to the Federal Motor Carrier Safety Administration (FMCSA): Overall the fatality rate for large truck crashes was 66 percent higher than passenger

More information

SFI SPECIFICATION 35.2 EFFECTIVE: DECEMBER 29, 2014 *

SFI SPECIFICATION 35.2 EFFECTIVE: DECEMBER 29, 2014 * SFI SPECIFICATION 35.2 EFFECTIVE: DECEMBER 29, 2014 * PRODUCT: Heavy Duty Stock Car Steel Wheels 1.0 GENERAL INFORMATION 1.1 This SFI Specification establishes uniform test procedures and minimum standards

More information

Electronic Reporting

Electronic Reporting Electronic Reporting Test TB31 of BS EN 1317 Parts 1 & 2 Test Number: TRL068 Trief Kerb and Pavement (Opinions and interpretations do not form part of this report.) TEST REPORT VIDEO FOOTAGE TRL068, Trief

More information

ROBUST PROJECT Norwegian Public Roads Administration / Force Technology Norway AS

ROBUST PROJECT Norwegian Public Roads Administration / Force Technology Norway AS ROBUST PROJECT Norwegian Public Roads Administration / Force Technology Norway AS Volume 1 of 1 April 2005 Doc. No.: ROBUST-05-009/TR-2005-0012 - Rev. 0 286-2-1-no-en Main Report Report title: Simulation

More information

SAFETY COMPLIANCE TESTING FOR FMVSS 124 ACCELERATOR CONTROL SYSTEMS

SAFETY COMPLIANCE TESTING FOR FMVSS 124 ACCELERATOR CONTROL SYSTEMS REPORT NUMBER 124-GTL-07-001 SAFETY COMPLIANCE TESTING FOR FMVSS 124 ACCELERATOR CONTROL SYSTEMS HYUNDAI MOTOR COMPANY 2007 HYUNDAI ELANTRA 4-DOOR PASSENGER CAR NHTSA NO. C70502 GENERAL TESTING LABORATORIES,

More information

City of Storm Lake Fire Department Heavy Rescue Specifications

City of Storm Lake Fire Department Heavy Rescue Specifications INTENT OF SPECIFICATIONS City of Storm Lake Fire Department Heavy Rescue Specifications It shall be the intent of these specifications to provide a complete apparatus equipped as hereinafter specified.

More information

SAFETY COMPLIANCE TESTING FOR FMVSS NO. 138 TIRE PRESSURE MONITORING SYSTEMS

SAFETY COMPLIANCE TESTING FOR FMVSS NO. 138 TIRE PRESSURE MONITORING SYSTEMS REPORT NUMBER 138-STF-10-008 SAFETY COMPLIANCE TESTING FOR FMVSS NO. 138 TIRE PRESSURE MONITORING SYSTEMS CHRYSLER GROUP, LLC 2010 DODGE RAM 1500 CREW CAB TRUCK NHTSA NO. CA0303 U.S. DOT SAN ANGELO TEST

More information

SHORT PAPER PCB OBLIQUE COLLISIONS ENGINEERING EQUATIONS, INPUT DATA AND MARC 1 APPLICATIONS. Dennis F. Andrews, Franco Gamero, Rudy Limpert

SHORT PAPER PCB OBLIQUE COLLISIONS ENGINEERING EQUATIONS, INPUT DATA AND MARC 1 APPLICATIONS. Dennis F. Andrews, Franco Gamero, Rudy Limpert SHORT PAPER PCB 8-2006 OBLIQUE COLLISIONS ENGINEERING EQUATIONS, INPUT DATA AND MARC 1 APPLICATIONS By: Dennis F. Andrews, Franco Gamero, Rudy Limpert PC-BRAKE, INC. 2006 www.pcbrakeinc.com 1 PURPOSE OF

More information

SAFETY COMPLIANCE TESTING FOR FMVSS NO. 214S SIDE IMPACT PROTECTION (STATIC)

SAFETY COMPLIANCE TESTING FOR FMVSS NO. 214S SIDE IMPACT PROTECTION (STATIC) REPORT NUMBER 214-GTL-09-002 SAFETY COMPLIANCE TESTING FOR S SIDE IMPACT PROTECTION (STATIC) MAZDA MOTOR CORPORATION 2009 MAZDA 3, PASSENGER CAR NHTSA NO. C95400 GENERAL TESTING LABORATORIES, INC. 1623

More information

Titre / Title HIGH RELIABILITY RF COAXIAL LOADS AND ATTENUATORS GENERIC SPECIFICATION

Titre / Title HIGH RELIABILITY RF COAXIAL LOADS AND ATTENUATORS GENERIC SPECIFICATION Date: December 19 th, 16 ISSUE: 1/B PAGE: 1 / 21 Titre / Title HIGH RELIABILITY RF COAXIAL LOADS AND ATTENUATORS GENERIC SPECIFICATION Rédigé par / Written by Responsabilité / Responsibility Date Signature

More information

NCHRP Report 350 Test 4-12 of the Modified Thrie Beam Guardrail

NCHRP Report 350 Test 4-12 of the Modified Thrie Beam Guardrail NCHRP Report 350 Test 4-12 of the Modified Thrie Beam Guardrail PUBLICATION NO. FHWA-RD-99-065 DECEMBER 1999 Research, Development, and Technology Turner-Fairbank Highway Research Center 6300 Georgetown

More information

2.0 TEST PROCEDURES AND RESULTS Vibration Test TEST EQUIPMENT AND INSTRUMENTATION QUALITY ASSURANCE PROGRAM 7 ATTACHMENTS

2.0 TEST PROCEDURES AND RESULTS Vibration Test TEST EQUIPMENT AND INSTRUMENTATION QUALITY ASSURANCE PROGRAM 7 ATTACHMENTS Page No. 2 TABLE OF CONTENTS Page No. 1.0 INTRODUCTION 3 1.1 Scope 3 1.2 References 3 1.3 Test Specimen Description 3 1.4 Summary 3 2.0 TEST PROCEDURES AND RESULTS 4 2.1 Vibration Test 4 3.0 TEST EQUIPMENT

More information

CRASH TEST OF MILE POST MARKER. T. J. Hirsch Research Engineer. and. Eugene Buth Assistant Research Engineer. Research Report Number 146-8

CRASH TEST OF MILE POST MARKER. T. J. Hirsch Research Engineer. and. Eugene Buth Assistant Research Engineer. Research Report Number 146-8 CRASH TEST OF MILE POST MARKER by T. J. Hirsch Research Engineer and Eugene Buth Assistant Research Engineer Research Report Number 146-8 Studies of Field Adaption of Impact Attenuation Systems Research

More information

REPORT NUMBER: 301-MGA SAFETY COMPLIANCE TESTING FOR FMVSS NO. 301 FUEL SYSTEM INTEGRITY

REPORT NUMBER: 301-MGA SAFETY COMPLIANCE TESTING FOR FMVSS NO. 301 FUEL SYSTEM INTEGRITY REPORT NUMBER: 301-MGA-2009-004 SAFETY COMPLIANCE TESTING FOR FMVSS NO. 301 FUEL SYSTEM INTEGRITY GIRARDIN MINIBUS, INC. 2008 GIRARDIN G5 SCHOOL BUS NHTSA NO.: C80902 PREPARED BY: MGA RESEARCH CORPORATION

More information

PROCUREMENT SPECIFICATIONS DELTA MODEL DSC 1500 PORTABLE BEAM - CRASH CERTIFIED BARRIER SYSTEM

PROCUREMENT SPECIFICATIONS DELTA MODEL DSC 1500 PORTABLE BEAM - CRASH CERTIFIED BARRIER SYSTEM PROCUREMENT SPECIFICATIONS DELTA MODEL DSC 1500 PORTABLE BEAM - CRASH CERTIFIED BARRIER SYSTEM Copyright 2019 Delta Scientific Corporation Page 1 of 8 SYNOPSIS This Procurement Specification defines a

More information

REPORT NUMBER: 214P-MGA SAFETY COMPLIANCE TESTING FOR FMVSS 214 DYNAMIC SIDE IMPACT PROTECTION RIGID POLE

REPORT NUMBER: 214P-MGA SAFETY COMPLIANCE TESTING FOR FMVSS 214 DYNAMIC SIDE IMPACT PROTECTION RIGID POLE REPORT NUMBER: 214P-MGA-211-11 SAFETY COMPLIANCE TESTING FOR FMVSS 214 DYNAMIC SIDE IMPACT PROTECTION RIGID POLE KIA MOTORS MANUFACTURING GEORGIA, INC. 211 KIA SORENTO SUV NHTSA NUMBER: CB511 PREPARED

More information

MASH TEST 3-11 OF THE TxDOT SINGLE SLOPE BRIDGE RAIL (TYPE SSTR) ON PAN-FORMED BRIDGE DECK

MASH TEST 3-11 OF THE TxDOT SINGLE SLOPE BRIDGE RAIL (TYPE SSTR) ON PAN-FORMED BRIDGE DECK TTI: 9-1002 MASH TEST 3-11 OF THE TxDOT SINGLE SLOPE BRIDGE RAIL (TYPE SSTR) ON PAN-FORMED BRIDGE DECK ISO 17025 Laboratory Testing Certificate # 2821.01 Crash testing performed at: TTI Proving Ground

More information

Crashworthiness Evaluation Offset Barrier Crash Test Protocol (Version III) June 1996

Crashworthiness Evaluation Offset Barrier Crash Test Protocol (Version III) June 1996 Crashworthiness Evaluation Offset Barrier Crash Test Protocol (Version III) June 1996 Insurance Institute for Highway Safety TEST CONDITIONS Impact Speed and Overlap Offset barrier crash tests are conducted

More information

REPORT NUMBER: 214P-MGA SAFETY COMPLIANCE TESTING FOR FMVSS 214 DYNAMIC SIDE IMPACT PROTECTION RIGID POLE

REPORT NUMBER: 214P-MGA SAFETY COMPLIANCE TESTING FOR FMVSS 214 DYNAMIC SIDE IMPACT PROTECTION RIGID POLE REPORT NUMBER: 214P-MGA-211-9 SAFETY COMPLIANCE TESTING FOR FMVSS 214 DYNAMIC SIDE IMPACT PROTECTION RIGID POLE TOYOTA MOTOR CORPORATION 211 SCION TC 3-DR LIFTBACK NHTSA NUMBER: CB517 PREPARED BY: MGA

More information

SAFETY COMPLIANCE TESTING FOR FMVSS 110 TIRE SELECTION AND RIMS

SAFETY COMPLIANCE TESTING FOR FMVSS 110 TIRE SELECTION AND RIMS REPORT NUMBER 110-STF-09-001 SAFETY COMPLIANCE TESTING FOR TIRE SELECTION AND RIMS GENERAL MOTORS CORPORATION 2009 CHEVROLET IMPALA FOUR-DOOR PASSENGER CAR NHTSA NO. C90100 U.S. DOT SAN ANGELO TEST FACILITY

More information

MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR PAVEMENT RIDE QUALITY (MEAN ROUGHNESS INDEX ACCEPTANCE CRITERIA)

MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR PAVEMENT RIDE QUALITY (MEAN ROUGHNESS INDEX ACCEPTANCE CRITERIA) MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR PAVEMENT RIDE QUALITY (MEAN ROUGHNESS INDEX ACCEPTANCE CRITERIA) CFS:TEH 1 of 10 APPR:KPK:JFS:07-07-16 FHWA:APPR:07-15-16 a. Description. This

More information

Incomplete Vehicle Document 2014 Model Year NOTE:

Incomplete Vehicle Document 2014 Model Year NOTE: NOTE: YOU CAN PRODUCE YOUR OWN LEGITIMATE INCOMPLETE VEHICLE DOCUMENT BY PRINTING THIS DOCUMENT AND THEN TAKING A PHOTO OF THE CERT. LABEL ON THE DRIVERS DOOR OPENING. 55351115AZ CHRYSLER GROUP LLC 800

More information

SPMM OUTLINE SPECIFICATION - SP20016 issue 2 WHAT IS THE SPMM 5000?

SPMM OUTLINE SPECIFICATION - SP20016 issue 2 WHAT IS THE SPMM 5000? SPMM 5000 OUTLINE SPECIFICATION - SP20016 issue 2 WHAT IS THE SPMM 5000? The Suspension Parameter Measuring Machine (SPMM) is designed to measure the quasi-static suspension characteristics that are important

More information

MASH TEST 3-11 OF THE TxDOT T222 BRIDGE RAIL

MASH TEST 3-11 OF THE TxDOT T222 BRIDGE RAIL TTI: 9-1002-12 MASH TEST 3-11 OF THE TxDOT T222 BRIDGE RAIL ISO 17025 Laboratory Testing Certificate # 2821.01 Crash testing performed at: TTI Proving Ground 3100 SH 47, Building 7091 Bryan, TX 77807 Test

More information

General Vehicle Information

General Vehicle Information Vehicle #3921 Chevrolet Equinox (2CNALBEW8A6XXXXXX) Inspection Date: 1-Feb-211 Year 21 Make Model Body Style HVE Display Name: Year Range: Sisters and Clones: Vehicle Category: Vehicle Class: VIN: Date

More information

HEAVY-DUTY 500,000-MILE BUS WITH A MINIMUM SERVICE LIFE OF 12 YEARS 5. STRUCTURAL INTEGRITY

HEAVY-DUTY 500,000-MILE BUS WITH A MINIMUM SERVICE LIFE OF 12 YEARS 5. STRUCTURAL INTEGRITY HEAVY-DUTY 500,000-MILE BUS WITH A MINIMUM SERVICE LIFE OF 12 YEARS 5. STRUCTURAL INTEGRITY 5.1. STRUCTURAL STRENGTH AND DISTORTION TESTS - STRUCTURAL SHAKEDOWN TEST April 2006 5.1-1 ABBREVIATIONS ABTC

More information

NFPA 286 STANDARD METHODS OF FIRE TESTS FOR EVALUATING CONTRIBUTION OF WALL AND CEILING INTERIOR FINISH TO ROOM FIRE GROWTH

NFPA 286 STANDARD METHODS OF FIRE TESTS FOR EVALUATING CONTRIBUTION OF WALL AND CEILING INTERIOR FINISH TO ROOM FIRE GROWTH NFPA 286 STANDARD METHODS OF FIRE TESTS FOR EVALUATING CONTRIBUTION OF WALL AND CEILING INTERIOR FINISH TO ROOM FIRE GROWTH Contego Latex Fire Barrier Intumescent (Also marketed in Canada by Pyrologistics,

More information

EFFECTIVENESS OF COUNTERMEASURES IN RESPONSE TO FMVSS 201 UPPER INTERIOR HEAD IMPACT PROTECTION

EFFECTIVENESS OF COUNTERMEASURES IN RESPONSE TO FMVSS 201 UPPER INTERIOR HEAD IMPACT PROTECTION EFFECTIVENESS OF COUNTERMEASURES IN RESPONSE TO FMVSS 201 UPPER INTERIOR HEAD IMPACT PROTECTION Arun Chickmenahalli Lear Corporation Michigan, USA Tel: 248-447-7771 Fax: 248-447-1512 E-mail: achickmenahalli@lear.com

More information

June 5, In Reply Refer To: HSSD/B-178. Mr. Kevin K. Groeneweg Mobile Barriers LLC Genesee Trail Road Golden, CO Dear Mr.

June 5, In Reply Refer To: HSSD/B-178. Mr. Kevin K. Groeneweg Mobile Barriers LLC Genesee Trail Road Golden, CO Dear Mr. June 5, 2008 1200 New Jersey Avenue, SE. Washington, DC 20590 In Reply Refer To: HSSD/B-178 Mr. Kevin K. Groeneweg Mobile Barriers LLC 24918 Genesee Trail Road Golden, CO 80401 Dear Mr. Groeneweg: This

More information

TITLE: EVALUATING SHEAR FORCES ALONG HIGHWAY BRIDGES DUE TO TRUCKS, USING INFLUENCE LINES

TITLE: EVALUATING SHEAR FORCES ALONG HIGHWAY BRIDGES DUE TO TRUCKS, USING INFLUENCE LINES EGS 2310 Engineering Analysis Statics Mock Term Project Report TITLE: EVALUATING SHEAR FORCES ALONG HIGHWAY RIDGES DUE TO TRUCKS, USING INFLUENCE LINES y Kwabena Ofosu Introduction The impact of trucks

More information

SAFETY COMPLIANCE TESTING FOR FMVSS NO. 202 HEAD RESTRAINTS STATIC REQUIREMENTS

SAFETY COMPLIANCE TESTING FOR FMVSS NO. 202 HEAD RESTRAINTS STATIC REQUIREMENTS REPORT NUMBER 202-GTL-08-004 SAFETY COMPLIANCE TESTING FOR FMVSS NO. 202 HEAD RESTRAINTS STATIC REQUIREMENTS HYUNDAI MOTOR MANUFACTURING ALABAMA, LLC 2008 HYUNDAI SONATA, PASSENGER CAR NHTSA NO. C80507

More information

SIDE IMPACT IIHS. Page 1 / 7. MESSRING Systembau MSG GmbH. Printing errors and omissions reserved

SIDE IMPACT IIHS. Page 1 / 7. MESSRING Systembau MSG GmbH. Printing errors and omissions reserved SIDE IMPACT IIHS Explore a moving barrier for tests of occupant protection! Equipped with an advanced brake system and individually calibrated by MESSRING. I Brake system for each wheel I Wireless or cable-controlled

More information

REPORT NUMBER: 305-MGA

REPORT NUMBER: 305-MGA REPORT NUMBER: 305-MGA-2011-001 SAFETY COMPLIANCE TESTING FOR FMVSS 305 Electric Powered Vehicles: Electrolyte Spillage and Electrical Shock Protection HONDA MOTOR CO., LTD 2011 HONDA CR-Z 3-DR HATCHBACK

More information

GENERAL SPECIFICATION

GENERAL SPECIFICATION ALPHA 2001 MD TMA (Truck Mounted Attenuator GENERAL SPECIFICATION I. GENERAL A. All ALPHA 2001 MD Truck Mounted Attenuators (ALPHA 2001 MD TMA) shall be designed and manufactured by Energy Absorption systems,

More information

Methodologies and Examples for Efficient Short and Long Duration Integrated Occupant-Vehicle Crash Simulation

Methodologies and Examples for Efficient Short and Long Duration Integrated Occupant-Vehicle Crash Simulation 13 th International LS-DYNA Users Conference Session: Automotive Methodologies and Examples for Efficient Short and Long Duration Integrated Occupant-Vehicle Crash Simulation R. Reichert, C.-D. Kan, D.

More information

SAFETY COMPLIANCE TESTING FOR FMVSS 110 TIRE SELECTION AND RIMS

SAFETY COMPLIANCE TESTING FOR FMVSS 110 TIRE SELECTION AND RIMS REPORT NUMBER 110-STF-10-004 SAFETY COMPLIANCE TESTING FOR FMVSS 110 TIRE SELECTION AND RIMS MAZDA MOTOR CORPORATION 2010 MAZDA 6 FOUR-DOOR PASSENGER CAR NHTSA NO. CA5402 U.S. DOT SAN ANGELO TEST FACILITY

More information

MASH08 TEST 3-11 OF THE ROCKINGHAM PRECAST CONCRETE BARRIER

MASH08 TEST 3-11 OF THE ROCKINGHAM PRECAST CONCRETE BARRIER Proving Ground Report No. 400001-RPC4 Report Date: July 2009 MASH08 TEST 3-11 OF THE ROCKINGHAM PRECAST CONCRETE BARRIER by C. Eugene Buth, P.E. Research Engineer William F. Williams, P.E. Assistant Research

More information

HEAVY-DUTY ARTICULATED 500,000-MILE BUS WITH A MINIMUM SERVICE LIFE OF 12 YEARS 7.1 INTERIOR NOISE TESTS

HEAVY-DUTY ARTICULATED 500,000-MILE BUS WITH A MINIMUM SERVICE LIFE OF 12 YEARS 7.1 INTERIOR NOISE TESTS HEAVY-DUTY ARTICULATED 500,000-MILE BUS WITH A MINIMUM SERVICE LIFE OF 12 YEARS 7. NOISE 7.1 INTERIOR NOISE TESTS April 2006 ABBREVIATIONS ABTC - Altoona Bus Test Center A/C - air conditioner ADB - advance

More information