Max Load. Max. Load. 100W 3-50VDC mA > 90% < 20% > 0.95 RFID P/N: XXXXXXXXXX CERTIFIED TO CSA STD. C22.2 NO.

Transcription

1 WIDTH DRIVEN HEIGHT MAGNITUDE LIGHTING AFLEX LINEAR DIMMABLE E DIM DOWN TO 0.1% CLASS P CLASS 2 QUICK SPECS The AFlex Series of Constant Current Programmable LED Drivers offers high efficiency, smooth flicker-free dimming and Dim to off capability. Magnitude s wireless programing technology (FlexTool) enables full flexibility for OEMs to easily con figure the drivers output current, dimming curve, dim-to-off, NTC settings and more. Programming the Driver doesn t require any power and can be done in less then one second. The auxiliary output provides power source for sensors and/or cooling devices and eliminates the need for an additional power supply. The Drivers wide operating window, dimming performance and programming options gives luminaire manufacturers high level of flexibility. As always, 5-year warranty is a standard on all of Magnitude lighting products. Input Voltage Max Power Voltage Current Max Load Max. Load Power Max. Load Envir. Protection Rating VAC / VDC +/-10% 100W 3-50VDC mA > 90% < 20% > 0.95 IP21 WIRING DIAGRAM Input White Black Green Gray Yellow N VAC 50\60Hz 12V / 24V AUX NTC DIM 0-10V LED RFID Orange Orange Purple Gray Red Blue FEATURES Compliant with Title 24 Requirements* Wireless RFID Programming - No power required 0-10V Dimmable - Dim Down to 0.1% Dim To Off Capability NTC - LED Temperature Sensor Auxiliary Power Wide Operating Window CLO (constant lumen output) Up to 90% Efficiency ENCLOSURE DETAILS In. (mm) Universal Input Voltage UL Listed 8750, Class 2, Class P Length 12 (304.8) Mounting Length 11.7 (296.8) Width Height 1.2 (30.5) 1.00 (25.4) INPUT: 120VAC 60HZ MAGNITUDE LENGTH CLASS 2 pending LED MAGNETIC DRIVER - 60W MAXIMUM P/N: XXXXXXXXXX NEMA 3R ENCLOSURE USE COPPER WIRE ONLY CONFORMS TO UL STD 8750 CERTIFIED TO CSA STD. C22.2 NO. 223 OUTPUT: 24VDC * Most models are compliant with Title 24 flicker, standby power, and start-up time requirements. Please contact Magnitude Lighting for more details. page 1

2 GENERAL Part Number: AFLEX- W- - - Driver Type: Constant Current Programming Tool: FlexTool Software: link SPECIFICATIONS *Specifications are at 25 c (unless specified otherwise) Input Input Voltage Range Input Frequency Input current Inrush Current Efficiency Power Factor VAC / VDC ± 10% 50 / 60Hz 1.2A@120VAC / 0.5A@277VAC 38A Max (refer to graph, page 10) > 90% (refer to graph, page 6) 0.99@120VAC / 0.98@277VAC (refer to graph, page 7) Voltage Range Current Range Current Tolerance Current Ripple Line Regulation Load Regulation Turn On Delay Time Sensor Power Supply (Auxiliary) Stand-By Power 3-50VDC mA (1mA step programmable) ± 5% ± max load ± 0.5% ± 0.5% 0.4 max load 12V / 24V up to 160mA (Programmable) < 1W Environmental Env. Protection Rating Surge Protection Operating Ambient temperature Operating temperature Storage temperature Expected life time EMI Compliance Audible Noise Withstanding Voltage IP 21 - indoor use only 2.5 KV -40ºc - +60ºc -40ºc - +75ºc -40ºc - +85ºc 50K hours at 75ºc (refer to graph, page 10) FCC 47CFR Part 15 Class B < 24db Class A 2.5 KV page 2

3 Dimming Dimming Control Dimming input Range Dimming Curves Min. Dimming level Dim to Off Current Consumption PWM Dimming 0-10V -2V - +15V Linear / Logarithmic (Programmable) Dim down to 0.1% Yes (Programmable) 0.35mA / Source 2000Hz LED Thermal Protection (NTC) - refer to page 8 NTC Value Manufaturer: Vishay 15 kω ± Manufacturer P/N: NTCS0805E3153JMT Level range 1mA step programmable (0-100%) Protections Over Current Protection Short Circuit Protection Over Voltage Protection Over Temperature Protection Mis-Wiring Protection Yes; current limit Yes; hiccup mode Yes; hiccup mode Yes; power derating (refer to graph, page 9) Yes; auto shutdown Mechanical & Housing Length Width Height Housing material Housing Color Junction Box Input Connectors type Connectors type Dimming Connectors type Auxiliary Connectors type NTC Connectors type Mounting 12 Inch (304.8mm) 1.2" Inch (30.5mm) 1.00" Inch (25.4mm) Aluminium Blue anodized No black & white/ Wago / 16-20AWG strip 3/8 red & blue / Wago / 16-20AWG strip 3/8 purple & gray / Wago / 16-20AWG strip 3/8 yellow & gray / Wago / 16-20AWG strip 3/8 orange & orange / Wago / 16-20AWG strip 3/8 Two hole flange mounting Approval markings Certificates/Approval signs UL 8750 class 2, class P page 3

4 MECHANICAL DIAGRAM R Tc page 4

5 FLICKER PERFORMANCE The IEEE P1789 flicker test results are presented graphically with no observable effect (green area), low-risk (yellow area), and high risk (red area) Modulation [%] 1 1mA 100mA 350mA 500mA 700mA 1050mA 1400mA 1650mA 2000mA Frequency [Hz] page 5

6 OPERATING RANGE 60 OUTPUT VOLTAGE [V] OUTPUT CURRENT [ma] DIMMING CURVES LINEAR LOGARITHMIC MAXIMUM DIMMING LEVEL LIGHT OUTPUT LEVEL 1.5V MINIMUM DIMMING LEVEL SWITCH OFF SWITCH ON V page 6

7 EFFICIENCY VS. OUTPUT VOLTAGE (120VAC) EFFICIENCY [%] mA 350mA 500mA 700mA 1100mA 1400mA 2000mA OUTPUT VOLTAGE [V] EFFICIENCY VS. OUTPUT VOLTAGE (277VAC) EFFICIENCY [%] mA 350mA 500mA 700mA 1100mA 1400mA 2000mA OUTPUT VOLTAGE [V] page 7

8 POWER FACTOR VS. OUTPUT POWER 1 POWER FACTOR VAC 277VAC OUTPUT POWER [W] THD VS. OUTPUT POWER THD [%] VAC 277VAC OUTPUT POWER [W] page 8

9 LED THERMAL PROTECTION (NTC) RFID The AFlex Series of drivers helps protect the LED's lifetime and will reduce the temperature of the LED module by derating the output current in case of high temperatures. The negative temperature coefficient (NTC) thermistor must be connected to the LED driver as shown in the wiring diagram. For maximum performance, the NTC thermistor must be placed close to the Tc point of the LED module. The power derating parameters can be programed using the FlexTool programmer. The NTC outputs can be left disconnected if thermal protection is not required. Input White Black Green Gray Yellow N VAC 50\60Hz 12V / 24V AUX NTC DIM 0-10V LED Orange Orange Purple Gray Red Blue NTC THERMISTOR Compatible NTC thermistor: Specification Manufacturer Manufacturer P/N 15 kω ± Vishay NTCS0805E3153JMT 120 Iout (%) VS. LED TEMPERATURE 100 Iout [%] LED TEMPERATURE [ºc] page 9

10 DRIVER THERMAL PROTECTION 120 Iout (%) VS. Tcase Iout [%] Tcase [ºc] Normal operation Derating area Protection area Return to work after thermal protection activated Min -40ºc +75ºc +80ºc +70ºc Max +75ºc +85ºc 5% LED drop allowed 10% LED drop allowed AWG mA ma ma AWG mA ma ma ft 7 ft 6 ft ft 15 ft 12 ft ft 12 ft 9 ft ft 23 ft 19 ft ft 19 ft 15 ft ft 37 ft 30 ft ft 36 ft 24 ft ft 59 ft 47 ft page 10

11 LIFETIME VS. Tcase LIFETIME (KHrs) Tcase [ºc] INRUSH CURRENT Vin [V] Ipeak [A] T Ipeak ) 120 VAC usec 277VAC usec Ipeak T Ipeak ) page 11

12 REMOTE INSTALLATION OUTPUT CURRENT VS. LED VOLTAGE OUTPUT CURRENT [A] L1=1ft. L2=100ft L3=300ft. L4=500ft. L5=1000ft LED VOLTAGE [V] TEST CONDITION: 1. Power = 100W 2. Current = 2A 3. Wire parameters = 18AWG, 16/ 30, 6.75Ω/ 1000 Note Above L=100ft. min LED voltage = 10V page 12

13 AFLEX LINEAR - ORDER PART NUMBER CONFIGURATION FOR EXAMPLE: 3. Case Style AFLEX- W Max Power (W) 2. Current 4. Dimming Curve 5. Auxilary Power 1. Max Power: 30 / 40 / 50 / 60 / 75 / 100W 2. Current: mA for 50Vout mA for 57Vout 3. Case Style: L - Linear / O - Outdoor Use (IP65). 4. Dimming Curve: L - For Linear / G - For Logarithmic 5. Auxilary Power: B - For 12V PS and 50V output C - For 24V PS and 50V output D - For NO AUX and 50V output E - For 12V PS and 57V output F - For 24V PS and 57V output G - For NO AUX and 57V output Please Note! for special requirements, please contact our sales team at: sales@magnitudeinc.com page 13

14 COMPATIBLE 0-10 DIMMER LIST Dimming Lutron Lutron Lutron Leviton Watt Stopper Lightolier Controls Phillips Part Number Diva - DVTV Diva - NFTV Nova T - NTFTV illumatech - IP7 DCLV1 ZP600FAM120 Sunrise - SR1200ZTUNV ISOLATION Isolation INPUT OUTPUT 0-10V Enclosure INPUT N/A 2xU+1kV 2xU+1kV 2xU+1kV OUTPUT 2xU+1kV N/A N/A 0.5kV 0-10V 2xU+1kV N/A N/A 0.5kV Enclosure 2xU+1kV 0.5kV 0.5kV N/A page 14

15 FLEXTOOL PROGRAMMING THE AFLEX DRIVER The FlexTool is a wireless programer used to program Magnitude s Flex Series of LED Drivers. By using the FlexTool, OEM s can quickly and smoothly configure the drivers parameters without applying power or wires to the driver. With the FlexTool software you can easily save driver configuration profiles to an external file and use as needed. The software provides graphic and audio indication that the driver was successfully configured. PROGRAMMABLE OUTPUT CURRENT 1mA step programmable. DIMMING CONTROL Dim to Off: yes/no (check box) Factory Default: yes Dimming Curve: Linear or Log. Factory Default: Linear Min. Dimming level before Dim to Off Dimming type: 0-10V / Non. Factory Default: 0-10V LED THERMAL PROTECTION Temperature Derating start. Factory Default: 70 C Temperature Derating end. Factory Default: 100 C Minimum Current Level Before Shutoff: 1mA page 15 MAGNITUDE LIGHTING The specifications are subject to change without notice Bentley Circle, Tustin, CA Customer Service: (714) Fax: (714) WE DRIVE LIGHT