SP PRO KACO Managed AC Coupling

Size: px

Start display at page:

Download "SP PRO KACO Managed AC Coupling"

Helen Wade
5 years ago
Views:

SP PRO KACO Managed AC Coupling Introduction The SP PRO KACO Managed AC Coupling provides a method of linking the KACO Powador xx00 and Powador xx02 series grid tie inverters to the SP PRO via the AC

1 SP PRO KACO Managed AC Coupling Introduction The SP PRO KACO Managed AC Coupling provides a method of linking the KACO Powador xx00 and Powador xx02 series grid tie inverters to the SP PRO via the AC Load supply so that regardless of whether the grid or a generator is connected, the SP PRO can manage and control the KACO grid tie inverters. Each SP PRO can manage a maximum of five KACO grid tie inverters by commanding each grid tie inverter to output the right amount of power that is needed to simultaneously supply the load, export any excess and maintain the battery bank at any particular point in time. This is done via a communications link which also serves to retrieve all the operational data for display and logging by the SP PRO. This document details the additional steps needed to install the managed system. The SP PRO and KACO inverters can be installed as per their individual installation instructions with the additional allowance of a communications cable linking all of the inverters. Note: This document needs to be read in conjunction with the SP PRO Instruction Manual and the KACO xx02 Series or KACO xx00 Series Instruction Manual. Overview The diagram below shows a managed AC coupled system with five KACO inverters. NOTE: The RS485 Communications links between the SP PRO and KACO Powador inverters can be either wired link (using CAT 5 cable) or a wireless link (Using the Optional Selectronic wireless RS485 link, stock code see Installation note IN0029 under the Support tab at the Selectronic web site for more details) IN0018 Revision 08 (004686) 1 of 18 POWER PERFORMANCE PASSION

2 System Requirements To successfully install a SP PRO KACO managed system, there are particular system requirements that need to be met. This installation document is applicable to SP PRO series II inverters only (revision 20 or greater). To install an AC coupled system using a series I SP PRO inverter an additional AC coupling adaptor (stock code ) is required. Combined maximum AC output of all the connected KACO inverters must not exceed twice the continuous SP PRO output power rating. Battery bank must be sized to suit the SP PRO model and the combined maximum AC Output power of the KACO inverters. SP PRO and KACO inverters must have appropriate firmware version installed. SP PRO MODEL AND TOTAL KACO AC OUTPUT The total AC output of the KACO inverters must not be greater than twice # the nominal capacity of the SP PRO. SP PRO Model Combined maximum KACO AC Output power SPMC240 6 kw SPMC241 9 kw SPMC kw SPMC kw SPMC kw SPLC kw SPLC kw # Table 1: Maximum KACO AC output per SP PRO model # - Reduced total KACO AC power limit for SPLC1202. The KACO AC Output must not exceed the maximums listed. Note: The AC Output of the KACO inverter should be reduced in line with the connected solar panels i.e. a 6002 inverter has an AC output of 5kW, yet if only 4kW of panels are installed then the lower power should be used. IN0018 Revision 08 (004686) 2 of 18

3 SP PRO MODEL AND MINIMUM BATTERY CAPACITY The minimum battery capacity that must be connected to the SP PRO inverter varies depending on SP PRO model, an overriding minimum battery capacity and the combined maximum KACO AC Output. The following table defines the minimum battery capacity for each SP PRO model. Combined max. KACO AC Output Minimum Battery Capacity SP PRO Model SPMC240 SPMC241 SPMC481 SPMC482 SPMC1201 SPLC1200 SPLC kw 180 Ah 180 Ah 180 Ah 180 Ah 100 Ah 250 Ah 250 Ah 2 kw 180 Ah 180 Ah 180 Ah 180 Ah 100 Ah 250 Ah 250 Ah 3 kw 240 Ah 240 Ah 180 Ah 180 Ah 100 Ah 250 Ah 250 Ah 4 kw 320 Ah 320 Ah 180 Ah 180 Ah 100 Ah 250 Ah 250 Ah 5 kw 400 Ah 400 Ah 200 Ah 200 Ah 100 Ah 250 Ah 250 Ah 6 kw 480 Ah 480 Ah 240 Ah 240 Ah 100 Ah 250 Ah 250 Ah 7 kw Ah 280 Ah 280 Ah 112 Ah 250 Ah 250 Ah 8 kw Ah 320 Ah 320 Ah 128 Ah 250 Ah 250 Ah 9 kw Ah 360 Ah 360 Ah 144 Ah 250 Ah 250 Ah 10 kw Ah 400 Ah 160 Ah 250 Ah 250 Ah 11 kw Ah 176 Ah 250 Ah 250 Ah 12 kw Ah 192 Ah 250 Ah 250 Ah 13 kw Ah 208 Ah 250 Ah 250 Ah 14 kw Ah 224 Ah 250 Ah 250 Ah 15 kw Ah 240 Ah 250 Ah 250 Ah 16 kw Ah 256 Ah 17 kw Ah 272 Ah 18 kw Ah 288 Ah 19 kw Ah 304 Ah 20 kw Ah 320 Ah 25 kw Ah 400 Ah 30 kw Ah 500 Ah 35 kw Ah Table 2: Minimum battery capacity per SP PRO model and Total KACO AC power Note 1: Shaded cells = minimum battery capacity Note 2: = n/a, maximum power exceeded for that SP PRO model. Note 3: Battery capacity is C10 rating. Note 4: Round battery capacity up as appropriate to available battery sizes. Ensure that the system meets these minimum battery capacity requirements. Any battery combinations larger than the minimum are suitable. IN0018 Revision 08 (004686) 3 of 18 POWER PERFORMANCE PASSION

SP PRO AND KACO FIRMWARE REQUIREMENTS The SP PRO units revision should be 20 or later (series II). Earlier unit revisions (series I) need an additional AC coupling adaptor (stock code 004665).

4 SP PRO AND KACO FIRMWARE REQUIREMENTS The SP PRO units revision should be 20 or later (series II). Earlier unit revisions (series I) need an additional AC coupling adaptor (stock code ). Packaging Label indicating Revision: 20 SP PRO Software Version 6.18 or later is required. To check software revision run SP LINK, connect to the SP PRO and go to Data View Technical Data SP PRO Revision and Software Version Older revisions of firmware must be updated to firmware revision 6.18 or later. Do NOT change any configuration settings until firmware is updated. Note: Selectronic web site for latest SP PRO firmware and Tech Note 34 SP PRO Firmware Update Procedure. IN0018 Revision 08 (004686) 4 of 18

KACO inverters prior to April 2013 do not have compatible firmware installed and cannot be updated.

5 KACO Powador xx00 Series KACO Powador xx00 Series inverters must be manufactured from April 2013 onwards to contain the compatible firmware. The label on compatible inverters is marked with 02/2013 or greater. This means the second quarter KACO inverters prior to April 2013 do not have compatible firmware installed and cannot be updated. KACO Powador xx02 Series KACO Powador xx02 Series inverters must be manufactured during 2011 or later to contain the compatible firmware. KACO inverters prior to 2011 do not have compatible firmware installed and cannot be updated. IN0018 Revision 08 (004686) 5 of 18 POWER PERFORMANCE PASSION

6 Installation The SP PRO and KACO inverters should be installed as per their respective installation instructions. Particular instructions directly related to Managed AC Coupling are listed below. It is good practice to number each KACO inverter from 1 up to 5 so that each inverter can be easily referenced within SP LINK. In a three phase AC coupled system label each KACO inverter L1-1 to L1-5 for the KACO inverters connected to SP PRO L1, L2-1 to L2-5 for those connected to L2 and so on. This number 1 to 5 is used for the Communications Link addressing. See Configuration section. KACO AC WIRING The KACO AC output wiring must be connected to the AC Load terminals of the SP PRO in accordance with local wiring rules for correct operation. KACO AC Wiring guide for Grid connected installation IN0018 Revision 08 (004686) 6 of 18

7 KACO AC Wiring guide for Off Grid connected installation Note: The system will NOT function correctly if the KACO inverters are installed on the AC Source side of the SP PRO. IN0018 Revision 08 (004686) 7 of 18 POWER PERFORMANCE PASSION

COMMUNICATIONS LINK (RS485) The communications link always starts at the SP PRO, then connects to all the KACO inverters in a daisy chain arrangement and finishes at the last KACO inverter.

Using the supplied CAT5 network cable, cut off one of the RJ45 connectors, expose and crimp the wires using supplied wire crimps or alternatively use a longer cable as required (not supplied) as

8 COMMUNICATIONS LINK (RS485) The communications link always starts at the SP PRO, then connects to all the KACO inverters in a daisy chain arrangement and finishes at the last KACO inverter. There is no need to connect the KACO inverters in any particular order. Using the supplied CAT5 network cable, cut off one of the RJ45 connectors, expose and crimp the wires using supplied wire crimps or alternatively use a longer cable as required (not supplied) as outlined in the table below. PLEASE NOTE: The wire colours in the table below may vary between different CAT5 cables. To ensure correct connections please check that the RS485 RJ45 Adaptor pin # corresponds to the KACO RS485 Connector connection by buzzing out the lead before connecting it to the KACO or the SP PRO inverter. Pin 1 RS485 RJ45 Adaptor Pin 1 designation Cut off one RJ45 Connector RS485 RJ45 Adaptor pin # Signal Typical Wire Colour (May vary with different CAT5 leads) KACO xx00 Series RS485 Connector 1 GND Green/White - 2 GND Green - KACO xx02 Series RS485 Connector GND 3 RS485 - B Orange/White B B 4 GND Blue GND Blue/White RS485 - A Orange A A 7 GND Brown/White GND Brown - - RS485 adaptor to KACO connections and wire colours Note: Only the wires connected to Pins 1,2,3,and 6 (on the RJ45) are used. IN0018 Revision 08 (004686) 8 of 18

9 Connect the RJ45 connector to the SP PRO RS485 Port 2 connection and the crimped wires to the RS485 port on the KACO inverter. SP PRO Connections (inside unit) RS485 Port 2 RJ45 connector IN0018 Revision 08 (004686) 9 of 18 POWER PERFORMANCE PASSION

10 KACO Powador xx00 Series RS485 Connections KACO xx00 Series RS485 Connections (inside unit) double plug in socket. On the KACO inverter there are two parallel connection sockets allowing looping through of the wiring to additional inverters. Either connection point is suitable. Green mating plugs are provided with each KACO unit included with mounting hardware plastic bag. When looped to another KACO, the termination switch position 2 should be set to OFF (away from ON). For the last KACO inverter on the Communications Link (RS485) (or when only one KACO inverter is used), the termination switch position 2 must be set to ON Last KACO on Communications Link (RS485), or when only 1 KACO is used: SW 2 ON (Terminator ON) Notes: 1. Green mating connector show is provided in plastic bag with mounting hardware 2. Wire colours may vary with different CAT5 cables. 3. Switch position 1 is always set to OFF 4. The Ground wire (GND) from the SP PRO RS485 communication link is not connected. IN0018 Revision 08 (004686) 10 of 18

KACO Powador xx02 Series KACO xx02 Series RS485 Connections (inside unit) spring loaded terminals On the KACO inverter there are two

When looped to another KACO, the termination switch position 1 should be set to OFF (away from ON).

must be set to ON Last KACO on Communications Link (RS485), or when only 1 KACO is used: SW 1 ON (Terminator ON) Notes: 1.

11 KACO Powador xx02 Series KACO xx02 Series RS485 Connections (inside unit) spring loaded terminals On the KACO inverter there are two parallel sets of connections allowing looping through of the wiring to additional inverters. Either connection point is suitable. When looped to another KACO, the termination switch position 1 should be set to OFF (away from ON). For the last KACO inverter on the Communications Link (RS485) (or when only one KACO inverter is used), the termination switch position 1 must be set to ON Last KACO on Communications Link (RS485), or when only 1 KACO is used: SW 1 ON (Terminator ON) Notes: 1. Wire colours may vary with different CAT5 cables. 2. Switch position 2 is always set to OFF KACO loop-through: SW 1 OFF (Terminator OFF) IN0018 Revision 08 (004686) 11 of 18 POWER PERFORMANCE PASSION

12 Configuration Additional Settings It is recommended that the Site Configuration wizard (in SP LINK 7.7 and above) be used to configure the SP PRO settings. Using the wizard will ensure all the SP PRO settings are compatible with the manage AC coupled system. The settings detailed below will be set when the Site Configuration Wizard is used to configure the SP PRO. Only the additional settings required to enable KACO Managed AC Coupling are shown. The remainder of systems settings will be set by the Site Configuration Wizard. The SP PRO must be configured before any of the KACO inverters are energised. The AC coupled failsafe system in the SP PRO is only enabled when the correct KACO configuration has been programmed into the SP PRO. The KACO inverters must be set to RS485 and appropriately addressed to ensure correct communications (see KACO Port Configuration section). SETTINGS THAT ARE SET BY SITE CONFIGURATION WIZARD In SP LINK CONFIGURATION SETTINGS SYSTEM the follow settings will be set. Enable KACO Link, KACO Com Port is set to RS485. Number of KACO inverters connected is set to the number of KACO inverters installed in the system. SP LINK - Configuration Settings System tab Note: Port 2 Communication settings will not be available once KACO Com port has been enabled. This is normal operation. In the example used above, only one KACO inverter is connected to the SP PRO. IN0018 Revision 08 (004686) 12 of 18

PROGRAMMING FALLBACK POWER INTO THE SP PRO INVERTER This section details the process for programming the SP PRO inverter in the system to enable fallback power mode.

13 PROGRAMMING FALLBACK POWER INTO THE SP PRO INVERTER This section details the process for programming the SP PRO inverter in the system to enable fallback power mode. Fall back power Mode is required when using a batteryless SP PRO configuration or when a wireless RS485 link is installed. It is highly recommended for ALL other managed AC coupled systems. Fall back power mode is a failsafe function that causes the output power of a KACO powador inverter to drop to zero if there is a failure in the RS485 communications link with the SP PRO. As soon as the RS485 communications link is restored the system will function again normally. Details for setting the KACO inverters to fallback power mode are provided in the next section. WARNING: It is important that both the SP PRO and ALL the connected KACO inverters are set to fallback Power mode to ensure correct system operation. 1. Check that the firmware revision of the SP PRO is 7.07 or greater. 2. Check that the firmware version on ALL connected KACO inverters is greater than or equal to the following (see next section for details on checking the KACO): a. ARM: V5.34 b. DSP: V In SP LINK, click on the Configuration Settings tab then System tab. Set the Fallback Power setting to Enable. 4. When the configuration is complete, Save Site to file (File / Site information / save). 5. Once the site has been saved then connect to the SP PRO using the Connect button or the Connection Menu. Once connected the configuration is sent to the SP PRO using the Configure SP PRO button in the Configuration Settings tab. IN0018 Revision 08 (004686) 13 of 18 POWER PERFORMANCE PASSION

14 KACO PORT CONFIGURATION The settings listed below are all that is required. The serial port on the KACO inverter must be set to RS485 and each inverter set to an inverter address from 1 through to 5 as appropriate. 1. Isolate the DC solar from the KACO inverter(s) (via the appropriate DC circuit breaker). 2. Disconnect the RS485 connection from the SP PRO. The KACO parameter settings cannot be accessed when the communications link is active between the SP PRO and the KACO(s). 3. Ensuring that the SP PRO AC Load supply is present at the KACO inverter, switch on the AC supply to the KACO inverter. 4. Wake up the KACO inverter by pressing and holding the Night Switch for 10 seconds. 5. Once the display is active on the KACO, enter parameter settings mode. To enter settings mode, hold down both keys 1 and 2 for approximately one second. Use key 1 to scroll through the various menu items. The menu is continuous. When the end is reached, the display automatically returns to the first item. Use the 2 key to change the parameter that is shown. The values here are also continuous, i.e. after you reach the maximum value, they return to the minimum value. IN0018 Revision 08 (004686) 14 of 18

6. Scroll to Interface setting and ensure that it is set to RS485. NOTE: The latest firmware in the Powador 00 series does not have the interface setting.

set to 1. b. If more than one KACO is installed then the addresses must be allocated sequentially starting from 1 (i.e. first KACO = 1, second KACO = 2, third KACO = 3 etc).

15 6. Scroll to Interface setting and ensure that it is set to RS485. NOTE: The latest firmware in the Powador 00 series does not have the interface setting. In this case the only interface is RS485 so no setting is required. 7. Scroll to Inverter Address setting. a. If only one KACO is installed then the address must be set to 1. b. If more than one KACO is installed then the addresses must be allocated sequentially starting from 1 (i.e. first KACO = 1, second KACO = 2, third KACO = 3 etc). It is best practice if the address number matches the labelled KACO number. Note: It is forbidden to skip any address numbers in the sequence when using multiple KACO inverters. 8. Save parameters, simultaneously press both keys 1 and If there are multiple KACO inverters installed, repeat for all others. 10. Reconnect the RS485 connection to the SP PRO. Note: See Menu Level 2 within KACO Operating Instructions. PROGRAMMING FALLBACK POWER INTO THE KACO POWADOR INVERTERS This section details the process for programming the KACO inverters in the system to enable fallback power mode. Details for setting the SP PRO to fallback power mode are provided in the previous section. WARNING: It is important that both the SP PRO and ALL the connected KACO inverters are set to fallback Power mode to ensure correct system operation. To set fallback power mode in the KACO inverters follow the instructions below. 1. Isolate the DC solar from the KACO inverter(s) (via the appropriate DC circuit breaker). 2. Disconnect the RS485 connection from the SP PRO. The KACO parameter settings cannot be accessed when the communications link is active between the SP PRO and the KACO(s). IN0018 Revision 08 (004686) 15 of 18 POWER PERFORMANCE PASSION

Once the display is active on the KACO, enter parameter settings mode (level 2 menu) by pressing keys 1 and 2 together. The firmware version will be displayed.

16 3. Ensuring that the SP PRO AC Load supply is present at the KACO inverter, switch on the AC supply to the KACO inverter. 4. Wake up the KACO inverter by pressing and holding the Night Switch for 10 seconds. 5. Once the display is active on the KACO, enter parameter settings mode (level 2 menu) by pressing keys 1 and 2 together. The firmware version will be displayed. Check that the firmware version is greater than or equal to the following: o ARM: V5.34 o DSP: V Press keys 1 and 2 together to return to main menu (level 1). Hold down key 2 for 20 seconds to get to the level 3 menu. Select Country is displayed 7. Keep pressing key 1 until Config. fallback power is displayed. Press key 2 to select yes. Press key 1 and the Fallback Power screen is displayed. 8. Press key 2 to change fallback power to 0000/1000. Press key 1 until Timeout setting appears. Adjust the setting to s using key 2 to change digit and key 1 to move to next digit. Press keys 1 and 2 together to save settings and return to main menu IN0018 Revision 08 (004686) 16 of 18

System Commissioning Additional Tests In addition to the normal system testing that would be performed, the following additional tests must be performed as detailed below.

into service. COMMUNICATIONS LINK (RS485) VERIFICATION The correct operation of the KACO Managed AC Coupling replies on the Communications Link.

17 System Commissioning Additional Tests In addition to the normal system testing that would be performed, the following additional tests must be performed as detailed below. The commissioning sequence should verify the SP PRO and its operation without any of the KACO inverters in operation and then once the steps below are performed, the KACO inverters can be brought into service. COMMUNICATIONS LINK (RS485) VERIFICATION The correct operation of the KACO Managed AC Coupling replies on the Communications Link. It is vital that the communications link (RS485) connection has been setup correctly before operating the AC coupled system. 1. Check that all the RS485 connections have been connected correctly. 2. Wake the KACO(s) up by pressing and holding the Night Switch for 10 seconds (if they are not already awake). In the case of multiple KACOs this must be done for each inverter. 3. In the Data View => Technical Data tab there should be live data for all the connected KACO inverters. As a minimum there should be a reading for the AC volts. a. If the KACO data is all zeros then check the RS485 wiring and connections. Take careful note that A connects to A, B to B between all KACO inverters and the RS485 Adaptor. For SP PRO Firmware version 7.07 or greater the Communication link may be further tested using the Powador Link Test found in SP LINK under the Service Settings tab. 1. Wake up the KACO inverters (as per step 2 above) 2. In the Service Settings tab click the Reset Counters button 3. Wait 2 minutes and check that the error count remains at zero for all the connected KACO inverters. (An error count of 1 or 2 is acceptable but in this case it is good practice to check the wiring and that the termination resistors are set correctly in the SP PRO and KACO. Once the Communications link has been verified for each KACO inverter, the DC feeds to each KACO inverter can be switch on and full system testing and verification performed. IN0018 Revision 08 (004686) 17 of 18 POWER PERFORMANCE PASSION

FALLBACK MODE VERIFICATION If Fallback mode has been set in the SP PRO Inverter and the KACO inverter(s) then its operation can easily be tested with the following process: 1.

18 FALLBACK MODE VERIFICATION If Fallback mode has been set in the SP PRO Inverter and the KACO inverter(s) then its operation can easily be tested with the following process: 1. Run the system so that each of the KACO inverters is producing power. This can be verified by reading the power on front display on each of the KACO inverters. 2. Unplug the RS485 connected from the SP PRO inverter. 3. After 5 seconds check that power produced by each of the KACO inverters has dropped to zero. This can be verified by reading the power on front display on each of the KACO inverters. 4. Plug the RS485 connecter back into the SP PRO inverter. The KACO inverters should start producing power again after a few seconds up to a few minutes. Operation The SP PRO will operate normally, exporting and charging as set and required. The KACO inverters will behave slightly differently than in straight grid tie operation if Fallback Power mode is NOT set. If Fall Back Power mode is NOT set, the KACO display may show External Limiting with a percentage listed afterwards. The external limiting message indicates that the SP PRO is controlling the KACO unit to maintain correct power to the loads, appropriate battery charge and solar burst limiting. Even when there is limited solar power available the External limiting may not show 100%. This is normal operation and DOES NOT necessarily mean that the power is being limited. Also, the KACO inverters display will be locked and no other screens will be able to be selected. Additional Information Selectronic web site or contact the Selectronic Sales Team IN0018 Revision 08 (004686) 18 of 18

SP PRO ABB Managed AC Coupling

SP PRO ABB Managed AC Coupling Introduction The SP PRO ABB Managed AC Coupling provides a method of linking the ABB PVI-3.0/3.6/4.2- TL-OUTD and ABB PVI-5000/6000-TL-OUTD string inverters to the SP PRO