ROLLER BLIND MOTORISATION. Product Information

Transcription

1 LLE BLIND MTISATIN Product Information

2 NEVE HAVE T DISCNNECT PWE T A MT WHEN PGAMMING HD motors are capable of being configured with all motors plugged into power. Each motor is added to the remote control much like the bluetooth pairing process of a mobile phone. LLE BLIND MTISATIN SLUTINS Quiet, F lexible and Sleek, Hunter Douglas Motorisation is your Solution. Hunter Douglas offers a range of premium and low cost motorisation products. We incorporate the best of technology and design to deliver complete solutions for the project, and simple operation for the user. ur motorisation options are ideal for use with our quantum roller blind hardware system, giving you a total solution package that encompasses sleek aesthetics as well as reliable operation. CMPEHENSIVE TECHNICAL SUPPT Hunter Douglas provides support should you have any technical enquiries or issues in regards to a motorisation project. CHILD SAFETY Motorising blinds is the perfect way to ensure child safety considerations are upheld. EMTES AND ACCESSIES Complementing the motorisation selection, Hunter Douglas offers a complete suite of accessories and control options to suit your needs with both style and functionality in mind. 5 YEA WAANTY* All Hunter Douglas motorisation products carry a 5 year warranty* for peace of mind. C-TICK ur motorisation products comply with the Electromagnetic Compatibility Standards in Australia and New Zealand and carry the C-Tick logo. This ensures our products do not interfere with other electrical devices in the home. INTEGATED CNNECTS The HD and HDQ motors offer a moulded integrated connector that plugs straight into the motor head, eliminating bulky in-line connectors or having to leave large holes drilled in the wall. Supply the electrician the power cord in advance, and a small 8mm round hole is all that is required. SET LIMITS DIECTLY THUGH THE MT HEAD HD and HDQ motors are capable of having their limits set by pressing the buttons integrated into the motor head. Perfect for when you're up the ladder and don't have the remote control. THE LATEST IN ADI FEQUENCY TECHNLGY All HD motors and remote controls communicate via the 2.4GHz frequency in a completely meshed network. This means each motor can talk to all other motors in the network and the remote control in both directions, simultaneously. The end result is superior range and the most reliable remote control network. FLEXIBLE INSTALLATIN The Hunter Douglas Quantum oller Blind bracket design allows up to 8 ways of rotation of the motor in the bracket, allowing more flexibility with every installation. Conditions Apply. *See for warranty document.

3 MT SELECTIN GUIDE HD PEMIUM MT SELECTIN GUIDE MEGE Motor Motor Diameter Typical Use* Product Codes /0# Product Description HDS37 25mm Switch Control - emote Control with optional receiver - Automation (12V switching) - Small / Narrow Blinds - 12 Volt Power HDM40SQ 35mm Switch Control - Automation - emote with optional Controller HDM40Q 35mm Advanced Automation - Bidirectional Intelligent BUS - Dry Contact Switch Control HDM40F 35mm emote Control - Switch Control (dry contact) - Automation HDM50S 45mm Switch Control - Automation - emote with optional Controller HDM50Q 45mm Advanced Automation - Bidirectional Intelligent BUS - Dry Contact Switch Control HDM50F 45mm emote Control - Switch Control (dry contact) - Automation Motor HDM25S (includes power cord) Motor Adaptor Kit 37mm (pack 5) DC Power Supply 12V 1.3A (1 motor PSU) DC Power Supply 12V 5A (4 motor PSU) Platinum Wall Switch DC F Platinum emote Control 4 Channel Platinum Wireless Wall Switch 4 Channel Motor HDSQ 3NM 30PM + ILC (includes power cord) Motor Adapter Kit 50mm HD M40 Q50 (pack 50) Motor Adapter Kit 50mm HD M40 Q50 (pack 5) Motor HDSQ 6NM 20PM + ILC (includes power cord) Motor HDM40Q426 (includes power cord) Motor Adapter Kit 50mm HD M40 Q50 (pack 50) Motor Adapter Kit 50mm HD M40 Q50 (pack 5) Motor HDM40Q914 (includes power cord) HDQ Bottom ail Tag (pack 100) Motor BUS Cable 1.8metre (pack 5) Dry Contact Switch Cable 1.8metre (pack 5) Motor HDM40F426 (includes power cord) Motor Adapter Kit 50mm HD M40 Q50 (pack 50) Suite emote 1 Channel (white) Suite emote 1 Channel (black) Motor Adapter Kit 50mm HD M40 Q50 (pack 5) Motor HDM40F914 (includes power cord) HD Bottom ail Tag (pack 100) Suite emote 4 Channel (white) Suite emote 4 Channel (black) Motor HDM50S626 (includes power cord) Motor HDM50S1530 (includes power cord) (See price list for optional tube adapters) Motor HDM50Q626 (includes power cord) Motor HDM50Q1530 (includes power cord) HDQ Bottom ail Tag (pack 100) Motor BUS Cable 1.8metre (pack 5) Dry Contact Switch Cable 1.8metre (pack 5) (See price list for optional tube adapters) Motor HDM50F626 (includes power cord) Motor HDM50F1530 (includes power cord) HD Bottom ail Tag (pack 100) Suite emote 1 Channel (white) Suite emote 1 Channel (black) Suite emote 4 Channel (white) Suite emote 4 Channel (black) *See price list for optional tube adapters Motor Motor Diameter Typical Use* Product Codes /0# Product Description M37 25mm emote Control - Small/Narrow Blinds - 12 Volt Power M37 Battery 25mm emote Control - Small/Narrow Blinds - 8 AA lithium batteries *See price list for additional options # =equired, =ptional XXXX = Available in 0155 (White), 1858 (Black) M 35mm emote Control MS 35mm Switch Control - Automation FT Motor Merger emote 0.7/31mm (includes power cord) DC Power Supply 12V 1A (1 motor PSU) M37 25mm Crown Drive Kit for Q37 (pack5) Merger emote 1 Channel Merger emote 4 Channel M37 Bottom ail Tag (pack 100) Motor Merger emote Battery 1/30 Merger Battery Tube White M37 25mm Crown Drive Kit for Q37 (pack5) Merger emote 1 Channel AA Lithium Battery 4 Pack (Note: 2 packs required) Merger emote 4 Channel M37 Bottom ail Tag (pack 100) Motor Merger emote 5/28 (includes power cord) M 40mm Crown Drive Kit for Q50 (pack 5) Merger emote 1 Channel Merger emote 4 Channel M Bottom ail Tag (pack 100) Motor Merger Switch 6/28 (includes power cord) MS 40mm Crown Drive Kit for Q50 (pack 5) *See price list for additional options # =equired, =ptional XXXX = Available in 0155 (White), 1858 (Black)

4 QUANTUM MTISATIN HD PEMIUM HDM40Q Advanced Automation HDM40Q contains a highly advanced in-built motor controller capable of bidirectional communication. Utilising the powerful Hunter Douglas Q protocol, commands can be sent and received via serial to virtually any automation or management system on the market. The motor can be moved to any one of 100 positions from fully opened to fully closed along with pre-programmed scenes. Designed for Quantum 50mm tube option. HDM40F emote Motor HDF is the latest in wireless motor technology incorporating bidirectional communication between each motor and the remote control to ensure that operation is always flawless and uninterrupted. M40F motors have an integrated radio receiver for simple one plug installation. Motors can be configured and operated from the modern touch sensitive 4 Channel SUITE remote control. Each M40F motor contains in-built zero voltage contacts for connection to automation systems or operation from a switch control. Designed for Quantum 50mm tube option. The HD Premium range of motors offer innovative Quantum oller Blind motorisation solutions featuring advanced technology with smooth and quiet operation. Designed and manufactured in Europe, these superior automation systems are highly reliable and engineered for technical excellence. Gearing evolution Patented hybrid planetary/ worm gear system for super quiet operation - sub 40 db sound levels. HDM40SQ Super Quiet Standard Motor The HDM40SQ is a super quiet 4 wire standard motor (active, neutral, earth and direction wires). Designed specifically for direct 240 volt switch operation, or for connection to many controller based automation systems. Designed for Quantum 50mm tube option. Includes an in line connector and 2.5m tail. HDM25S Low Voltage Standard Motor HDM25S is a 25mm DC-12 volt motor designed to operate inside the Quantum 37mm tube and is ideal for use in narrow blinds. ne of the quietest motors on the market, HDM25S is a standard switch controlled motor, or can be integrated into various automation systems with in-built controllers. HDF BIDGE Unlock the potential of the HDF wireless motorisation range with a HDF Bridge unit, allowing interconnectivity between the HDM40F/HDM50F motors and other automation systems. CENTAL CMMAND SYSTEM The HDF Bridge acts as an integration device, converting S232 serial commands from an automation system into wireless F commands to the HDF motor. Users can control their motorised blinds from one central location, as a single HDF Bridge allows users to transmit UP/DWN/ STP/MVE T control commands via most automation system devices. ne HDF Bridge unit can handle at least 60 individual motors, without requiring BUS cables or cords. EMTE CNTL PTIN If desired, one HD 4 channel remote control can be joined to the network allowing control of up to 15 motors. MIC CNTL MVE T positions can be commanded in extremely small 1% increments between 0% and 99% of the full open position, allowing very fine control of each individual blind. FLEXIBLE CNFIGUATIN The HDF Bridge can be retrofit and additional motors can easily be added to the network over time. ADVANCED TECHNLGY Different groups of blinds can be configured to operate together, allowing for a highly individualised outcome for the user. For example, you can set-up options to send commands to a whole house, one particular room or just one individual blind. Installers can also program scenes allowing a group of blinds to move to a predetermined position, so users can control their entire home with a single touch. SIMPLE PGAMMING Using simple programming language, it s possible to easily configure different groups of commands to allow for a variety of advanced control options.

5 MT: HDSQ 3/30 MT: HDSQ 6/20 The HDS motor is a super quiet 240 volt AC motor used for switch operation, or from automation systems with 240 volt blind control modules such as C-Bus. The HDSQ motor is a super quiet 240 volt AC motor used for switch operation, or from automation systems with 240 volt blind control modules such as C-Bus. Technical Data HDSQ 3/30 Technical Data HDSQ 6/20 HSDQ Item Code Motor Length 511mm (see blind width below 620mm) Power Cable Length 2500mm Torque (NM) 3NM Speed 30 PM Limit Type Manual Weight 1.4Kg ated Voltage 240 V AC ated Current 0.42 Amps Motor Sound Level Less than 40dba (according to IS3746) un Time 4 minutes Tube Type / Diameter Quantum50 35mm motor Typical Use oller blind, switch control or automation with optional controller Minimum blind width 620mm Maximum blind width 3300mm Maximum SQM 18 metres (based on fabric weight of 450gsm) Light Gap 21mm (outside bracket to bracket) In-line Square16mm diameter A = 511mm B = 12mm C=35mm HSDQ Item Code Motor Length 542mm (see blind width below 620mm) Power Cable Length 2500mm Torque (NM) 6NM Speed 20 PM Limit Type Manual Weight 1.4Kg ated Voltage 240 V AC ated Current 0.9 Amps Motor Sound Level Less than 40dba (according to IS3746) un Time 4 minutes Tube Type / Diameter Quantum50 35mm motor Typical Use oller blind, switch control or automation with optional controller Minimum blind width 620mm Maximum blind width 3300mm Maximum SQM 40 metres (based on fabric weight of 450gsm) Light Gap 21mm (outside bracket to bracket) In-line Square16mm diameter A = 542mm B = 12mm C=35mm 1. Super quiet, less than 40 dba (according to IS3746) 2. Large single or double linked blinds 3. 16mm square in-line connector. 4. Manufactured in Italy 1. Super quiet, less than 40 dba (according to IS3746) 2. Large single or triple linked blinds 3. 16mm square in-line connector. 4. Manufactured in Italy ptions and Accessories 4 Core 240V AC power cord with an in-line connector. Cable length, 2.5meter. /Natural//Direction Item: Used to connect/disconnect a HDSQ motor from the power source ptions and Accessories 4 Core 240V AC power cord with an in-line connector. Cable length, 2.5meter. /Natural//Direction Item: Used to connect/disconnect a HDSQ motor from the power source 4-Core-Wire Direction () Green/ Blue/ White/ /Direction Brown/ 4-Core-Wire Direction () Green/ Blue/ White/ /Direction Brown/ Switch or 240V Switching elay Switch or 240V Switching elay Motor Side oll Direction UP DWN Left Standard / Back White Brown Left everse / Brown White ight Standard / Back Brown White ight everse / White Brown Motor Side oll Direction UP DWN Left Standard / Back White Brown Left everse / Brown White ight Standard / Back Brown White ight everse / White Brown AC 240 Volt power cable As viewed from the termination end of the power cord. Setting Motor Limits Do Not Parallel Wire It is not possible to parallel wire 4 wire motors. A Motor Controller or separate switch must be used for each motor. Irreversible damage to motors will result if parallel wired. Wiring Information All wiring and electrical work must be performed by a qualified and certified electrician complying with local standards. AC 240 Volt power cable As viewed from the termination end of the power cord. Setting Motor Limits Do Not Parallel Wire It is not possible to parallel wire 4 wire motors. A Motor Controller or separate switch must be used for each motor. Irreversible damage to motors will result if parallel wired. Wiring Information All wiring and electrical work must be performed by a qualified and certified electrician complying with local standards. Limit settings can be adjusted using a limit setting tool, hex key or flat head screwdriver. Power must be supplied to the motor in the direction required in order to set the limits. Turn the limit screws in the direction indicated above to increase or decrease blind travel. Limit settings can be adjusted using a limit setting tool, hex key or flat head screwdriver. Power must be supplied to the motor in the direction required in order to set the limits. Turn the limit screws in the direction indicated above to increase or decrease blind travel. Limit Setting Limit Setting

6 PEMIUM: HDS/M50S The HDS motor is an exceptionally quiet 240 volt AC motor used for switch operation, or from automation systems with 240 volt blind control modules such as C-Bus. ptional motor controls can also provide remote control and other input types. 4-Core-Wire Direction () Green/ Blue/ White/ /Direction Brown/ Technical Data HDS/M50S HDM50S626 HDM50S1530 Item Code Motor Length 503mm (see blind width below 600mm) 561mm (see blind width below 650mm) Power Cable Length 2500mm (included) 2500mm (included) Torque (NM) 6NM 15NM Speed 26 PM 30PM Limit Type Manual Manual ated Voltage 240 V AC 240 V AC ated Current 0.56 Amps 1.08 Amps un Time 4 minutes 4 minutes Tube Type / Diameter Quantum65 45mm motor Quantum65 45mm motor Typical Use oller blind, switch control or automation with optional controller oller blind, switch control or automation with optional controller Minimum blind width 600mm 650mm Maximum SQM 27 metres (based on fabric weight of 450gsm) 75 metres (based on fabric weight of 450gsm) In-line emovable motor head plug emovable motor head plug AC 240 Volt power cable As viewed from the termination end of the power cord. 2 Button CLIPSAL Saturn Series Switch Wiring Diagram Switch or 240V Switching elay Do Not Parallel Wire It is not possible to parallel wire 4 wire motors. A Motor Controller or separate switch must be used for each motor. Irreversible damage to motors will result if parallel wired. Wiring Information All wiring and electrical work must be performed by a qualified and certified electrician complying with local standards. 2 Button Switch Diagram Motor Side oll Direction UP DWN Left Standard / Back White Brown Left everse / Brown White ight Standard / Back Brown White ight everse / White Brown 1. Large single or linked blinds 2. emovable motor head plug 3. Exceptionally quiet and smooth operation 4. Manufactured in Italy ptions and Accessories 240V AC Single Motor Control. Enables dry contact switch control, Infrared, F and keypad options to operate a single blind. Item: Used to offer enhanced control of a standard 4 wire motor. Input options such as remote control, keypads and dry contact switching. Setting Motor Limits 240V AC Dual Motor Control. Enables dry contact switch control, Infrared, F and keypad options to operate two blinds. Item: Used to offer enhanced control of two standard 4 wire motors. Input options such as remote control, keypads and dry contact switching. Platinum emote Control and eceiver option for Motor Controls Item: P to Platinum eceiver Item: Platinum 4 Channel emote Control Item: Platinum 4 Channel Wireless Wall Switch Platinum receiver can be attached to motor controls to enable F control of blinds with the Platinum emote Control or wireless wall switch. ESI/P emote Control and receiver option for Motor Controls Item: ESI eceiver emote Controls, Wireless and Wired wall control in 24 Channel, 6 Channel and 2 Channel - See Price list for details Dry Contact Switch in a single and double configuration. Used in conjunction with motor control to enable wall switch control Item: Single Item: Double ESI/P receiver can be attached to motor control to enable F and I remote control, as well as F and wired key pads. Enables zero voltage (dry contact) wall switch control of the HDS motor. When used in conjunction with the Single or Dual Motor Control. Limit Setting Limit settings can be adjusted using a limit setting tool, hex key or flat head screwdriver. Power must be supplied to the motor in the direction required in order to set the limits. Turn the limit screws in the direction indicated above to increase or decrease blind travel. 2 Button Clipsal Saturn Series switches. Item: cean Mist Item: Black Can be wired directly to a HDS motor to enable UP/STP/DWN control of the blind. The bottom button supplies power, the top button changes direction. (See diagram over page). ESI/P Bus Cables enable the networking of motor controls. Lengths from 20, 10, 5, 1.8 metres and 30cm See price list. EI/P Bus cable is used to form a network of blind controls.

7 PEMIUM: HDQ/M40Q The HDQ motor is an exceptionally quiet 240 volt AC motor used for automation projects. An inbuilt controller with Q technology enables bidirectional communication over S232 with high-end automation or building management systems. The motor may be additionally connected to a wall switch or automation system from the integrated dry contact connectors on the motor head. 2 Metres - Pin 1 - Pin 2 - Pin 3 Technical Data HDQ/M40Q HDM40Q426 HDM40Q914 Item Code Motor Length 587mm (minimum blind width 700mm) 606mm (minimum blind width 700mm) Power Cable Length 2000mm (included with motor) 2000mm (included with motor) Torque (NM) 4 NM 9NM Speed 26 PM 14PM Limit Type Electronic Electronic Contact Type Integrated dry contact programmable SPST, SPDT, maintained or momentary action Integrated dry contact programmable SPST, SPDT, maintained or momentary action Automation Type Integrated Q Protocol 6 PIN S232 serial via Q Bridge Integrated Q Protocol 6 PIN S232 serial via Q Bridge ated Voltage 240 V AC 240 V AC ated Current 0.42 Amps 0.60 Amps un Time 4 minutes 4 minutes Tube Type / Diameter Quantum50 35mm motor Quantum50 35mm motor Typical Use oller blind, switch control or automation oller blind, switch control or automation Minimum blind width 700mm 700mm Maximum blind width 3300mm 3300mm Maximum SQM 24 metres (based on fabric weight of 450gsm) 60 metres (based on fabric weight of 450gsm) Light Gap 22mm (outside bracket to cloth) 22mm (outside bracket to cloth) AC 240 Volt Power Cable Integrated power connector plugs straight into the motor head. Q Network Wiring Guide HDQ Motor Connections 65mm Motor Side Profile Motor can be rotated 8 different positions on the bracket to achieve the best mounting location Switch Cable (ptional) 1.8 METE Switch (ptional) Motor Bus Cable 30 CM Control Buttons Motor Left Profile Control buttons can be used to set limits and operate the blind after installation. Q 6 Pin Power Dry Contact Motor ear Profile Q 6 Pin connector for Automation system connection and Dry contact connector allows switch or automation control. Pin1 pen, Pin2 Common, Pin3 - Close. 1. Integrated Q controller for high-end bidirectional automation integration. 2. Large single or linked blinds 3. Integrated power connector on motor head (no unsightly in-line connectors) ptions and Accessories QBridge enables S232 serial input to the motor network to communicate bidirectionally to an automation system. Item: Splitters in 2,3 and 5 motor combinations. Item: motor splitter Item: motor splitter Item: motor splitter Motor Bus Cable plugs directly into the motor head to enable motor network connection via the 6 pin J12 plug. Item: metres Item: cm Integrated Power 240V AC. Plug connects directly into the motor head (no in-line connector required). Power cord length 2 metres. Item: Switch Cable. 3 Pin dry contact switch cable enables independent control of the motor from a switch or automation system. pen/common/close. Cord length 2 metres. Item: Dry contact switch in a single and double configuration. Used in conjunction with switch cable to enable wired wall switch control of the HDQ motor. Item: Single Item: Double Bus Cable. 6 core with J12 connector on each end. Supports Q protocol communication. Item: metres Item: cm S232 Adapter. 9 Pin D-Sub female. Item: Exceptionally quiet and smooth operation. 5. Electronic limits for fast button setup from the motor head 6. Integrated contact connectors on the motor head enables switch control or automation integration. 7. Manufactured in Italy and the U.S.A equired on an Q protocol network to communicate between the motor network and an automation system. Combine motors together to build an Q protocol network. Splitters can be daisy-chain together to add hundreds of motors to an Q network. Daisy-chain motors together using J12 splitters to integrate into advanced automation systems using S232 serial. Power cord included with the motor. Can also be ordered separately. The switch type is programmable and supports both momentary and maintained SPDT or SPST switch types. Enables wired wall switch control of the HDQ motor. Daisy-chain splitters together or use to connect from the QBridge to an automation system. Connect via a Bus Cable from the QBridge to an automation system. TECHNICAL INFMATIN Setting Motor Limits: HDQ Power Cable - Included with Motor Total bus cable length must not exceed 300 metres nly one motor bus cable must connect to bus port on splitter All other motors must connect to aux port on splitter For extra cable length between motors - cat5 data cable can be used efer to hdq motor wiring and programming guide for more information Set the First Limit Press and hold the red flashing light on the motor head until the desired limit height is reached. To set this limit, press and hold the centre button, then while holding the centre button, press and hold the red flashing button until the light glows orange. Now release both buttons simultaneously. The limit will be set correctly when the green light begins flashing. Set the Second Limit Press and hold the green flashing light on the motor head until the desired limit height is reached. Splitter 2 MT MT MT To set this limit, press and hold the centre button, then while holding the centre button, press and hold the green flashing button until the light glows orange. Now release both buttons simultaneously. The limit will be set correctly when all lights go out. Motor Direction nce connected to the Automation system test motor direction, if the motor travel direction needs to be changed. Press and hold the two outer buttons simultaneously for 10 seconds. eset Limits Clears Both Limits To reset the motor limits, PESS and HLD the centre button for 10 seconds, or until centre button glows ANGE. elease and both limits will be cleared. Follow limit setting procedure to re-set limits. For Further Information please refer to the Hunter Douglas HDQ Motor Wiring and Programming Guide. QBridge Bus Cable 30 CM METE Dry Contact Switches 3 pin zero voltage dry contact inputs from optional switch cable. S232 Adapter BACK To Automation System

8 PEMIUM: HDQ/M50Q The HDQ motor is an exceptionally quiet 240 volt AC motor used for automation projects. An inbuilt controller with Q technology enables bidirectional communication over S232 with high-end automation or building management systems. The motor may be additionally connected to a wall switch or automation system from the integrated dry contact connectors on the motor head. 2 Metres - Pin 1 - Pin 2 - Pin 3 Technical Data HDQ/M50Q 65mm HDM50Q626 HDM50Q1530 Item Code Motor Length 581mm (minimum blind width 700mm) 639mm (minimum blind width 750mm) Power Cable Length 2000mm (included with motor) 2000mm (included with motor) Torque (NM) 6 NM 15NM Speed 26 PM 30PM Limit Type Electronic Electronic Q 6 Pin Power Dry Contact Control Buttons Contact Type Automation Type Integrated dry contact programmable SPST, SPDT, maintained or momentary action Integrated Q Protocol 6 PIN S232 serial via Q Bridge Integrated dry contact programmable SPST, SPDT, maintained or momentary action Integrated Q Protocol 6 PIN S232 serial via Q Bridge AC 240 Volt Power Cable Integrated power connector plugs straight into the motor head. Motor Side Profile Motor can be rotated 8 different positions on the bracket to achieve the best mounting location Motor Left Profile Control buttons can be used to set limits and operate the blind after installation. Motor ear Profile Q 6 Pin connector for Automation system connection and Dry contact connector allows switch or automation control. Pin1 pen, Pin2 Common, Pin3 - Close. ated Voltage 240 V AC 240 V AC ated Current 0.8 Amps 1.1 Amps un Time 4 minutes 4 minutes Tube Type / Diameter Quantum65 45mm motor Quantum65 45mm motor Typical Use oller blind, switch control or automation oller blind, switch control or automation Minimum blind width 700mm 750mm Maximum SQM 27 metres (based on fabric weight of 450gsm) 75 metres (based on fabric weight of 450gsm) Q Network Wiring Guide HDQ Motor Connections Switch Cable (ptional) 1.8 METE Switch (ptional) Motor Bus Cable 30 CM Integrated Q controller for high-end bidirectional automation integration. 2. Large single or linked blinds 3. Integrated power connector on motor head (no unsightly in-line connectors) 4. Exceptionally quiet and smooth operation. 5. Electronic limits for fast button setup from the motor head 6. Integrated contact connectors on the motor head enables switch control or automation integration. 7. Manufactured in Italy and the U.S.A Power Cable - Included with Motor To Automation System QBridge S232 Adapter ptions and Accessories QBridge enables S232 serial input to the motor network to communicate bidirectionally to an automation system. Item: Splitters in 2,3 and 5 motor combinations. Item: motor splitter Item: motor splitter Item: motor splitter Motor Bus Cable plugs directly into the motor head to enable motor network connection via the 6 pin J12 plug. Item: metres Item: cm Integrated Power 240V AC. Plug connects directly into the motor head (no in-line connector required). Power cord length 2 metres. Item: Switch Cable. 3 Pin dry contact switch cable enables independent control of the motor from a switch or automation system. pen/common/close. Cord length 2 metres. Item: Dry contact switch in a single and double configuration. Used in conjunction with switch cable to enable wired wall switch control of the HDQ motor. Item: Single Item: Double equired on an Q protocol network to communicate between the motor network and an automation system. Combine motors together to build an Q protocol network. Splitters can be daisy-chain together to add hundreds of motors to an Q network. Daisy-chain motors together using J12 splitters to integrate into advanced automation systems using S232 serial. Power cord included with the motor. Can also be ordered separately. The switch type is programmable and supports both momentary and maintained SPDT or SPST switch types. Enables wired wall switch control of the HDQ motor. TECHNICAL INFMATIN Total bus cable length must not exceed 300 metres nly one motor bus cable must connect to bus port on splitter All other motors must connect to aux port on splitter For extra cable length between motors - cat5 data cable can be used efer to hdq motor wiring and programming guide for more information Setting Motor Limits: HDQ Set the First Limit Press and hold the red flashing light on the motor head until the desired limit height is reached. To set this limit, press and hold the centre button, then while holding the centre button, press and hold the red flashing button until the light glows orange. Now release both buttons simultaneously. The limit will be set correctly when the green light begins flashing. Set the Second Limit Press and hold the green flashing light on the motor head until the desired limit height is reached. Splitter 2 MT MT MT To set this limit, press and hold the centre button, then while holding the centre button, press and hold the green flashing button until the light glows orange. Now release both buttons simultaneously. The limit will be set correctly when all lights go out. Motor Direction nce connected to the Automation system test motor direction, if the motor travel direction needs to be changed. Press and hold the two outer buttons simultaneously for 10 seconds. eset Limits Clears Both Limits To reset the motor limits, PESS and HLD the centre button for 10 seconds, or until centre button glows ANGE. elease and both limits will be cleared. Follow limit setting procedure to re-set limits. Bus Cable 30 CM METE BACK Bus Cable. 6 core with J12 connector on each end. Supports Q protocol communication. Item: metres Item: cm Daisy-chain splitters together or use to connect from the QBridge to an automation system. For Further Information please refer to the Hunter Douglas HDQ Motor Wiring and Programming Guide. Dry Contact Switches 3 pin zero voltage dry contact inputs from optional switch cable. S232 Adapter. 9 Pin D-Sub female. Item: Connect via a Bus Cable from the QBridge to an automation system.

9 MT: HD/M40F The HD motor is an exceptionally quiet 240 volt AC motor used for single or linked blinds. perated by the modern sleek touch sensitive emote Control in 1 or 4 channels, or additionally connected to an automation system or wall switch from the integrated dry contact connectors. - Pin 1 - Pin 2 - Pin 3 Technical Data HD/M40F 2 Metres HDM40F426 HDM40F914 Item Code Motor Length 587mm (minimum blind width 700mm) 606mm (minimum blind width 700mm) Power Cable Length 2000mm (included with motor) 2000mm (included with motor) Torque (NM) 4 NM 9NM Speed 26 PM 14PM Limit Type Electronic Electronic Contact Type Integrated dry contact open/common/close Integrated dry contact open/common/close F Frequency 2.4Ghz ( ) 2.4Ghz ( ) ated Voltage 240 V AC 240 V AC ated Current 0.42 Amps 0.60 Amps un Time 4 minutes 4 minutes Tube Type / Diameter Quantum50 35mm motor Quantum50 35mm motor Typical Use oller blind remote control, switch control or automation Minimum blind width 700mm 700mm Maximum blind width 3300mm 3300mm Maximum SQM 24 metres (based on fabric weight of 450gsm) oller blind remote control, switch control or automation 60 metres (based on fabric weight of 450gsm) AC 240 Volt Power Cable Integrated power connector plugs straight into the motor head. emote Control Technical Information 65mm Motor Side Profile Motor can be rotated 8 different positions on the bracket to achieve the best mounting location. Control Buttons Motor Left Profile Control buttons can be used to set limits and operate the blind after installation. Switch Technical Information Antenna Power Dry Contact Motor ear Profile Dry contact connector allows switch or automation control. Pin1 pen, Pin2 Common, Pin3 - Close. Back Light Gap 22mm (outside bracket to cloth) 22mm (outside bracket to cloth) BACK 1. Large single or linked blinds 2. Touch sensitive remote control for individual, group control. Also enables several groups to be operated together. 3. Integrated power connector on motor head (no unsightly in-line connectors) 4. Exceptionally quiet and smooth operation. ptions PTINS and AND Accessories ACCESSIES 4 Channel Touch Sensitive emote Control. Allows a maximum of 4 groups of 4 motors (16 motors in total). Individual group control is possible. Eg. Individual groups can be independently selected and operated. Item White: Item Black: Channel Touch Sensitive emote Control. Allows a maximum of 1 group of 4 motors (4 motors in total). Item White: Item Black: emote Control Wall Kit. Item White: Item Black: Integrated Power. Plug connects directly into the motor head (no in-line connector required). Power cord length 2 metres. Item: Switch Cable. 3 Pin dry contact switch cable enables independent control of the motor from a three position switch. pen/common/close can also be used for Automation Systems. Item: Dry Contact Switch (in a single and double configuration) used in conjunction with switch cable to enable wired wall switch control of the HD motor. Item: Double Item: Single HDF Switch Transmitter Wireless Wall Switch Control from a three position switch, or combine with the dry contact switch above to allow F (wireless) wall switch control of the HD motor. Can also be used to control HD motors from Automation Systems. Item: HDF Bridge.The HDF Bridge is an Automation gateway capable of converting S232 serial commands from an Automation system into wireless F commands to the HD motor. Item: Electronic limits for fast button setup from the motor head or from the remote control. 6. Integrated contact connectors on the motor head enables switch control or automation integration. 7. Manufactured in Italy and the U.S.A 8. Superior F range by utilising a bidirectional meshed network. Individual motors relay commands to other motors. emote control used to setup motor network, invite motors and remotes into the network and set motor limits. emote control used to setup motor network, invite motors and remotes into the network and set motor limits. Designed to house the 4 channel or 1 channel remote control in a fixed position on a wall. Power cord included with the motor. Can also be ordered separately. Switch Cable used to enable wall switch control or integration with building management systems. Enables Wired Wall Switch Control of the HD motor. Up to send the blind up, Down to send the blind down, and a double press in either direction to stop the blind part way up or down. Wireless Wall Switch Control of up to 16 HD motors from one HDF Switch Interface. (4 groups of 4 motors) Wirelessly control up to 60 x HD motors from most Automation systems, all from one HDF Bridge. ne Channel emote Single channel remote can control 1 group of up to 4 motors (motors travel together). Quick Setup Instructions: HD Four Channel emote Four channel remote can control 4 individual motors or 4 groups of 4 motors = 16 total motors (each group of 4 motors travel together). The first motor powered on and paired to the emote Control will become the HUB motor and must be powered on at all times to add additional motors to the emote Control. Power n First Motor Power on first motor and wait for the motor to jog twice. Alternatively, if motor is currently powered on, press the centre button on the motor head of the desired HUB motor 3 times to simulate a motor reboot. Pair emote Control After HUB motor has jogged within 1 minute power on the remote control by pressing the up or down button. The motor will automatically pair to the remote and the UP/DWN lights will be flashing. Set Limits Press UP to move blind to the desired limit. Press and hold the UP and STP buttons simultaneously until blind jogs to set UP limit. Press DWN to move blind to the desired limit. Press and hold the DWN and STP buttons simultaneously until blind jogs to DWN limit. Change Motor Direction Press and HLD the UP and DWN buttons simultaneously until the motor jogs. Set Intermediate Stop perate the blind to the desired openness. Press and hold PESET Button until the motor jogs and the Intermediate limit will be set. Set Blind To User Mode Simultaneously press the STP and CHANNEL 1 Button. The ED light will turn off on the Preset button and the blind is now in user mode. See over-side to add additional blinds to the remote control. Dry Contact Switches 3 pin zero voltage dry contact inputs from optional switch cable. Double tap button to stop blind while in travel. AUTMATIN SYSTEM HDF Switch Transmitter Wireless switch control programable to accept SPDT and SPST momentary switches. Can be used with Dry Contact Switches or Automation Systems to provide a wireless control solution. Add Additional Motors To The emote Control Hub Motor Must Be n Ensure the HUB (or first configured motor) is powered on. Enter Motor Admin Mode Simultaneously press and HLD the STP and CHANNEL 1 Buttons on emote Control until the ED light is on the PESET Button. The HUB motor will jog twice when successful. Set Invitation Mode n Hub Motor Press the STP button on the remote control and the Green light will start flashing on the present button on the remote and the ANGE light will begin flashing on the HUB motor head and will flash for 1 minute. Alternatively, press the centre button on the motor head to set to invitation mode. Add Next Motor Power on the next motor to be added to the emote Control within 1 minute of setting the HUB motor to invitation mode. Alternatively if the new motor is already on, press the centre button on the motor head of the new motor to be added 3 times within 1 second to reboot the motor. Set Limits The new motor will pair to the remote on the next available channel. The UP/DWN buttons will be flashing. Set limits as per LIMIT SETTING instructions. SET INTEMEDIATE STP See ther Side SET BLIND T USE MDE See ther Side SET BLIND T USE MDE See ther Side Change Channel Number To change the Channel number, enter ADMIN MDE (Hold STP and CHANNEL 1 together) select the existing channel number of the blind, then PESS and HLD the new Channel Number. The blind will jog to acknowledge the change. To reset motor, clear limits and other instructions, refer to Motor User Guide.

10 MT: HD/M50F The HD motor is an exceptionally quiet 240 volt AC motor used for single or linked blinds. perated by the modern sleek touch sensitive emote Control in 1 or 4 channels, or additionally connected to an automation system or wall switch from the integrated dry contact connectors. - Pin 1 - Pin 2 - Pin 3 Technical Data HD/M40F 2 Metres HDM50F426 HDM50F1530 Item Code Motor Length 581mm (minimum blind width 700mm) 639mm (minimum blind width 750mm) Power Cable Length 2000mm (included with motor) 2000mm (included with motor) Torque (NM) 6NM 15NM Speed 26 PM 30PM Limit Type Electronic Electronic Contact Type Integrated dry contact open/common/close Integrated dry contact open/common/close F Frequency 2.4Ghz ( ) 2.4Ghz ( ) ated Voltage 240 V AC 240 V AC ated Current 0.80 Amps 1.10 Amps un Time 4 minutes 4 minutes Tube Type / Diameter Quantum65 45mm motor Quantum65 45mm motor 65mm Antenna Power Dry Contact Typical Use oller blind remote control, switch control or automation Minimum blind width 700mm 750mm oller blind remote control, switch control or automation AC 240 Volt Power Cable Integrated power connector plugs straight into the motor head. emote Control Technical Information Motor Side Profile Motor can be rotated 8 different positions on the bracket to achieve the best mounting location. Control Buttons Motor Left Profile Control buttons can be used to set limits and operate the blind after installation. Switch Technical Information Motor ear Profile Dry contact connector allows switch or automation control. Pin1 pen, Pin2 Common, Pin3 - Close. Back Maximum SQM 27 metres (based on fabric weight of 450gsm) 75 metres (based on fabric weight of 450gsm) BACK 1. Large single or linked blinds 2. Touch sensitive remote control for individual, group control. Also enables several groups to be operated together. 3. Integrated power connector on motor head (no unsightly in-line connectors) 4. Exceptionally quiet and smooth operation. PartPTINS ptions and AND Accessories ACCESSIES Description Common Uses 4 Channel Touch Sensitive emote Control. Allows a maximum of 4 groups of 4 motors (16 motors in total). Individual group control is possible. Eg. Individual groups can be independently selected and operated. Item White: Item Black: Channel Touch Sensitive emote Control. Allows a maximum of 1 group of 4 motors (4 motors in total). Item White: Item Black: emote Control Wall Kit. Item White: Item Black: Integrated Power. Plug connects directly into the motor head (no in-line connector required). Power cord length 2 metres. Item: Switch Cable. 3 Pin dry contact switch cable enables independent control of the motor from a three position switch. pen/common/close can also be used for Automation Systems. Item: Dry Contact Switch (in a single and double configuration) used in conjunction with switch cable to enable wired wall switch control of the HD motor. Item: Double Item: Single HDF Switch Transmitter. Wireless Wall Switch Control from a three position switch, or combine with the dry contact switch above to allow F (wireless) wall switch control of the HD motor. Can also be used to control HD motors from Automation Systems. Item: Electronic limits for fast button setup from the motor head or from the remote control. 6. Integrated contact connectors on the motor head enables switch control or automation integration. 7. Manufactured in Italy and the U.S.A 8. Superior F range by utilising a bidirectional meshed network. Individual motors relay commands to other motors. emote control used to setup motor network, invite motors and remotes into the network and set motor limits. emote control used to setup motor network, invite motors and remotes into the network and set motor limits. Designed to house the 4 channel or 1 channel remote control in a fixed position on a wall. Power cord included with the motor. Can also be ordered separately. Switch Cable used to enable wall switch control or integration with building management systems. Enables Wired Wall Switch Control of the HD motor. Up to send the blind up, Down to send the blind down, and a double press in either direction to stop the blind part way up or down. Wireless Wall Switch Control of up to 16 HD motors from one HDF Switch Interface. (4 groups of 4 motors) ne Channel emote Single channel remote can control 1 group of up to 4 motors (motors travel together). Quick Setup Instructions: HD Four Channel emote Four channel remote can control 4 individual motors or 4 groups of 4 motors = 16 total motors (each group of 4 motors travel together). The first motor powered on and paired to the emote Control will become the HUB motor and must be powered on at all times to add additional motors to the emote Control. Power n First Motor Power on first motor and wait for the motor to jog twice. Alternatively, if motor is currently powered on, press the centre button on the motor head of the desired HUB motor 3 times to simulate a motor reboot. Pair emote Control After HUB motor has jogged within 1 minute power on the remote control by pressing the up or down button. The motor will automatically pair to the remote and the UP/DWN lights will be flashing. Set Limits Press UP to move blind to the desired limit. Press and hold the UP and STP buttons simultaneously until blind jogs to set UP limit. Press DWN to move blind to the desired limit. Press and hold the DWN and STP buttons simultaneously until blind jogs to DWN limit. Change Motor Direction Press and HLD the UP and DWN buttons simultaneously until the motor jogs. Set Intermediate Stop perate the blind to the desired openness. Press and hold PESET Button until the motor jogs and the Intermediate limit will be set. Set Blind To User Mode Simultaneously press the STP and CHANNEL 1 Button. The ED light will turn off on the Preset button and the blind is now in user mode. See over-side to add additional blinds to the remote control. Dry Contact Switches 3 pin zero voltage dry contact inputs from optional switch cable. Double tap button to stop blind while in travel. AUTMATIN SYSTEM HDF Switch Transmitter Wireless switch control programable to accept SPDT and SPST momentary switches. Can be used with Dry Contact Switches or Automation Systems to provide a wireless control solution. Add Additional Motors To The emote Control Hub Motor Must Be n Ensure the HUB (or first configured motor) is powered on. Enter Motor Admin Mode Simultaneously press and HLD the STP and CHANNEL 1 Buttons on emote Control until the ED light is on the PESET Button. The HUB motor will jog twice when successful. Set Invitation Mode n Hub Motor Press the STP button on the remote control and the Green light will start flashing on the present button on the remote and the ANGE light will begin flashing on the HUB motor head and will flash for 1 minute. Alternatively, press the centre button on the motor head to set to invitation mode. Add Next Motor Power on the next motor to be added to the emote Control within 1 minute of setting the HUB motor to invitation mode. Alternatively if the new motor is already on, press the centre button on the motor head of the new motor to be added 3 times within 1 second to reboot the motor. Set Limits The new motor will pair to the remote on the next available channel. The UP/DWN buttons will be flashing. Set limits as per LIMIT SETTING instructions. SET INTEMEDIATE STP See ther Side SET BLIND T USE MDE See ther Side SET BLIND T USE MDE See ther Side Change Channel Number To change the Channel number, enter ADMIN MDE (Hold STP and CHANNEL 1 together) select the existing channel number of the blind, then PESS and HLD the new Channel Number. The blind will jog to acknowledge the change. To reset motor, clear limits and other instructions, refer to Motor User Guide. HDF Bridge.The HDF Bridge is an Automation gateway capable of converting S232 serial commands from an Automation system into wireless F commands to the HD motor. Item: Wirelessly control up to 60 x HD motors from most Automation systems, all from one HDF Bridge.

11 PEMIUM: HDS37/M25S The HDS37 motor is an exceptionally quiet low voltage motor used for small width blinds. With the ability to motorise blinds as narrow as 450mm the HDS37 motor can be used in C-Bus (or other automation installation), or combined with the Platinum Wired Wall Switch to enable both wall switch control and remote control operation simultaneously. Simple UP/DWN control of the blind using the front switch. Infrared control using the Platinum emote Control by pointing at the I receiver eye. F Module (included) allows F Control from the Platinum Wired emote control or Platinum Wireless Wall Switch. Dry contact harness for relay/switch control from Automation systems. Technical Data HDS37/M25S Item Code Motor Length 351mm (minimum blind width 450mm) Power Cable Length 2000mm (included with motor) Torque (NM) 0.6 NM Speed 28 PM Limit Type Electronic ated Voltage 12 V ated Current 1.2 Amps / 14.4 Watts un Time 2 minutes n/ff Tube Type / Diameter Quantum37 25mm Motor Typical Use ollerblind automation or switch/remote (when used with Platinum Wired Wall Switch) Minimum blind width 450mm Maximum blind width 2400mm Maximum SQM 6 metres (based on fabric weight of 450gsm) Light Gap 18mm to 20mm (outside bracket to cloth) The I receiver eye is also used when programming an F channel from the Platinum Wired emote Control or Platinum Wireless Wall Switch. Connecting Wires ne Motor, ne Switch Two Motors, Two Switches Communications port for advanced automation via S Ideal for narrow blinds Volt power Electrician may not be required to install (varies state by state). 3. Exceptionally quiet operation. 4. Electronic limits for fast button setup from the motor head. 5. Manufactured in the U.S.A ptions and Accessories Platinum Wired Wall Switch enables the HDS37 motor to be switch operated, or remote control operated through the inbuilt F and Infrared receiver. Combine up to 3 motors per switch to allow group operation. Item: Platinum emote Control allows 4 individual group channels to be used as well as an ALL channel for combined (group) operation. Multiple blinds can be associated to each group channel. Item: Platinum Wireless Wall Switch allows 4 individual group channels to be used as well as an ALL channel for combined (group) operation. Multiple blinds can be associated to each group channel. With the option to fix permanently on a wall, means no more lost remote controls! Item: Power Supply DC 12 Volt 5 Amps. Capable of powering up to four HDS37 motors. Item: Combine with HDS37 to enable wall operation and remote control with both F and Infrared. For remote control operation when HDS37 is combined with Platinum Wired Wall Switch. Can be used to control other Platinum products. For wall mounted remote control operation when HDS37 is combined with Platinum Wired Wall Switch. Can be used to control other Platinum products. Installation of up to four HDS37 motors. Can be used on multiple Platinum Wired Wall Switches as long as the total motors do not exceed four. 1. Insert small screwdriver. 2. Pull back on screwdriver to open the wire terminal Connection. 3. Insert wire into the circular wire terminal connector. 4. emove screwdriver to lock the wire. Automation Small power supply can be used for one motor/ switch. The Platinum Wired Wall Switch has both dry contact inputs and outputs to allow access to advanced control systems, as well as mechanical switches or relays. A communications port is also available for automation systems utilising S232 serial control. efer to remote control/wireless switch guide for programming remote controls to the wall switch. Large power supply can be used for up to 4 motors/switches. It is possible to connect multiple (up to 3 maximum) HDS37 motors to each individual switch. In this scenario, all motors will act as a group when travelling up/down from the switch or remote control. Setting Limits and Programming To set the motor limits on the M25S/HDS37 motor when connected to the Platinum Wired Wall Switch, follow the instructions below to place the wall switch into constant power mode. 1) Press and hold BTH UP and DWN buttons (the LED will not change) (if motor was moving it will stop). 2) After holding both buttons for 2.5 seconds, the relay will click and apply power continuously (LED will blink). 3) Both buttons must be released within 2 seconds after the relay activates. 4) All remote controls will be ignored when in constant power mode. 5) Set the Limits for the motor by following the instructions in the Quick Setup Guide. 6) To exit this mode (once motor limits are set) press either UP or DWN buttons on the Platinum Wired Wall Switch. Power Supply DC 12 Volt 1.3 Amps. Capable of powering a single HDS37 motor. Item: For single operation of a HDS37 motor or Platinum Wired Wall Switch.

12 MEGE SWITCH/MS The MS Motor is a 240 volt AC switch motor used for single or linked blinds. The motor is designed to be controlled from a 240 volt switch or from automation systems with 240 volt blind control modules. MEGE MTS KEY FEATUES The Merger ange of motors are designed with a focus on remote control and switch operated functionality at an extremely competitive price. The Merger low-cost solution makes motorised blinds accessible for everybody. MEGE EMTE M/M37/M37 BATTEY The M motor is a 240 volt AC remote control motor used for single or linked blinds, operated by a 1 or 4 channel remote control. The M37 motor is a 12 volt DC powered motor for small or narrow blinds. The M37 battery motor utilises 8 AA batteries and is designed for the Quantum 37mm tube.

13 MT: MEGE EMTE/M/M37/M BATTEY The M motor is a price competitive 240 volt AC remote control motor used for single or linked blinds. perated by a 1 or 4 channel remote control. The M37 and Merger Battery motor is a 12V DC powered motor for small or narrow blinds. MT: MEGE SWITCH/MS The MS motor is a price competitive 240 volt AC switch motor used for single or linked blinds. The motor is designed to be controlled from a 240V switch or from automation systems with 240 volt blind control modules. Technical Data Merger emote 5/28 35mm (M) Merger emote 25mm (M37) Merger Battery 25mm 1/30 Item Code Motor Length 560mm (minimum blind width 680mm) 280mm (minimum blind width 400mm) 265mm (minimum blind width 400mm) Power Cable Length 2800mm (included with motor) 650mm(from motor) 30cm (from motor) Battery tube length 535mm Torque (NM) 5 NM 0.7 NM 1 NM Speed 28 PM 31 PM 30 PM Limit Type Electronic Electronic Electronic Contact Type None None None F Frequency 433 Mhz 433 Mhz 433 Mhz ated Voltage 240 V AC 12 V DC 12 V DC Battery powered(8x AA Lithium batteries) ated Current 0.49 Amps 0.74 Amps 0.74 Amps un Time 4 minutes Continuous Continuous Tube Type / Diameter Edge50 35mm motor Edge37 25mm motor Edge37 25mm motor Typical Use oller blind remote control oller blind remote control oller blind remote control Minimum blind width 680mm 400mm 400mm Maximum blind width 3300mm 2400mm 2400mm Maximum SQM 30 metres (based on fabric weight of 450gsm) 6 metres (based on fabric weight of 450gsm) 8 metres (based on fabric weight of 450gsm) Light Gap 20mm (outside bracket to cloth) 18mm (outside bracket to cloth) 18mm (outside bracket to cloth) M Technical Data M Item Code Motor Length Power Cable Length Torque (NM) Speed Limit Type Contact Type F Frequency ated Voltage ated Current un Time Tube Type / Diameter Typical Use Minimum blind width Maximum blind width Maximum SQM Light Gap Merger Switch 6/28 FT mm (minimum blind width 680mm) 3000mm (included with motor) 6 NM 28 PM Manual None No F 240 V AC 0.53 Amps 4 minutes Quantum50 35mm motor oller blind switch control 680mm 3300mm 36 metres (based on fabric weight of 450gsm) 23mm (outside bracket to cloth) 1. Large single or linked blinds (M) 2. Small or narrow blinds (M37) Volt power (M37) - Electrician may not be required to install (varies state by state) Volt DC battery powered (Merger Battery) ptions and Accessories Motor Wiring Information AC 240 Volt power cable As viewed from the termination end of the power cord. Quick Setup Instructions PAI EMTE CNTL Power on first blind to be paired to the remote control. Ensure all other blinds are not connected to power. Within 10 seconds, on the remote control select the desired channel then press and HLD both the UP and DWN buttons simultaneously, then press the STP button. CHANGE MT DIECTIN (M) Press and hold the ED button on the motor head until the motor jogs. The motor direction will be changed. CHANGE MT DIECTIN (M37) Press Up and Down buttons simultaneously. Press the STP button 6 times, now Press the DWN button once. SET TP LIMIT Press UP to move blind to the desired limit. Press and hold the UP and DWN buttons simultaneously, then press the STP button 2 times within 10 seconds. Press the UP button once within 10 seconds. The limit will be set. SET BTTM LIMIT Press DWN to move blind to the desired limit. Press and hold the UP and DWN buttons simultaneously, then press the STP button 2 times within 10 seconds. Press the DWN button once within 10 seconds. The limit will be set and 4 channel remote control for individual or group control. 6. Power cable with in-line connector (M) 7. Simple programming and setup from the remote control. 8. Slim battey tube (Merger Battery) 9. Manufactured in China 4 Channel remote control with wall clip. Item: Channel remote control with wall clip. Item: Merger emote Molex cable with inline connector. Cable length 2.8 metres Item: Merger emote 25mm 12 volt, 1 AMP with DC power supply. Cable length 2 metres Item: Merger Battery Tube White 12 volt DC battery tube for merger Battery Motor. Cable length 730mm Item: For controlling up to 4 blind individually or unlimited motors can be paired to each channel and operated as a group. emote control used to setup motor network, invite motors and remotes into the network and set motor limits. Power cable for connecting to M 240 Volt Merger emote motor. Power cord included with motor, can also be ordered separately. Power supply required for operation with M37 12 volt motor. Power supply required for operation with Merger Battery Motor INTEMEDIATE STP perate the blind to the desired intermediate position. Press the STP button 4 times. The motor will jog and the intermediate is set. To travel to the intermediate position, press and hold the STP button for more than 2 seconds. DELETE TP LIMIT Press and hold the UP and DWN buttons simultaneously, then press the STP button 4 times within 10 seconds. Press the UP button once within 10 seconds. The limit will be cleared. DELETE BTTM LIMIT Press and hold the UP and DWN buttons simultaneously, then press the STP button 4 times within 10 seconds. Press the DWN button once within 10 seconds. The limit will be cleared CLEA EMTE CNTL PAIING FM MT Press and hold the UP and DWN buttons simultaneously, then press the STP button 7 times within 10 seconds. Press the UP button once within 10 seconds. The remote control will be removed from the motor. 1. Large single or linked blinds Volt switch control or via Automation systems with blind control modules 3. Power cable with in-line connector 4. Manual limit (screw type) for setting upper and lower limits 5. Manufactured in China ptions and Accessories PTINS AND ACCESSIES Motor Wiring Information Direction () AC 240 Volt power cable As viewed from the termination end of the power cord. Merger Switch Molex cable with inline connector. Cable length 3 metres Quick Setup Instructions Switch or 240V Switching elay Green/ Blue/ Black//Direction Brown/ Do Not Parallel Wire It is not possible to parallel wire 4 wire motors. A Motor Controller or separate switch must be used for each motor. Irreversible damage to motors will result if parallel wired. Motor Side oll Direction UP DWN Left Standard / Back White Brown Left everse / Brown White ight Standard / Back Brown White ight everse / White Brown Power cable for connecting to Merger Switch motor Wiring Information All wiring and electrical work must be performed by a qualified and certified electrician complying with local standards. Limit settings can be adjusted using a limit setting tool, hex key or flat head screwdriver. Power must be supplied to the motor in the direction required in order to set the limits. Turn the limit screws in the direction indicated above to increase or decrease blind travel.

14 QUANTUM TM LLE BLIND HADWAE VEVIEW 24/7 MTISATIN TECHNICAL SUPPT ALFI.HUNTEDUGLAS.CM.AU ALFI is a Motorisation and Installation Support website that's available for any device and platform. ALFI offers your team; 24/7 technical information whilst onsite Instant troubleshooting support Answers to most commonly asked questions Simple and quick navigation FEE to access Globally Inspired, exquisitely crafted, inherently strong and made for Australia. Featuring a sleek architectural design with smooth operation and unrivalled inner strength, the QUANTUM TM oller Blind Hardware System spans even the largest window expanses beautifully. Quantum is an innovative roller blind hardware system that features: complete suite of quality products easy assembly and installation sleek aesthetics with inner strength worldwide input into the design and engineering of the system HEAVY DUTY QUANTUM S smooth and reliable operation has been supersized with the introduction of the Heavy Duty oller Blind system, offering a complete suite of products for allsized projects, big or small. All Hunter Douglas motorisation options are optimised for use in conjunction with Quantum, giving you a total solution package. The ALFI website has been designed to assist installers with the ability to troubleshoot, program, setup and install new motorised blinds for various Hunter Douglas products. The website consists of numerous 30 second videos documenting the setup and troubleshooting processes for the full Hunter Douglas motorisation range. It also includes all supporting documents for each motorisation product including technical data sheets and operation manuals.