Turbo M Series onboard charger
|
|
- Christian Boone
- 5 years ago
- Views:
Transcription
1 Turbo M Series onboard charger Operation Manual Model # Output Bank Max. Output Turbo M Amps Turbo M Amps Turbo M Amps Turbo M Amps Turbo M Amps Turbo M Amps Turbo M Amps Turbo M Amps Turbo M Amps Battery System (DC) 12V 24V 36V 48V
2 Important Notice This manual contains important safety, operation, and installation instructions. Please read the entire instructions before using your Powermania Turbo M onboard battery charger. WARNING: CHECK BATTERY TYPE. This charger should be used to charge only Lead Acid type of 12V DC batteries; Flooded Lead- Acid, AGM (Absorbent Glass Mat), and GEL (Gelled Electrolyte Lead-Acid). Use of this product to charge other types of batteries may cause batteries to burst and result in personal injuries. If you are unsure about the type of battery, please consult with battery manufacturers. WARNING: RISK OF EXPLOSIVE GASES! Working in the vicinity of lead acid batteries is dangerous. Batteries generate explosive gases during normal operation. For this reason it is extremely important to follow safety instructions each time before using this charger. WARNING: DO NOT USE 2-PIN AC ADAPTER/EXTENSION CORD. Do NOT use the charger with a 2-pin AC adapter or extension cord. Do NOT cut or make any modification to the factory equipped AC power cord. Doing so can result in serious personal injury. CAUTION: CONNECT ONLY TO PROPERLY GROUNDED OUTLET. The charger MUST ONLY be connected to a properly grounded AC outlet that is protected by Ground Fault Circuit Interrupter (GFCI) breaker. DANGER: ALWAYS UNPLUG AC POWER CORD BEFORE MAKING ANY DC WIRING CONNECTION. The AC power cord MUST be UNPLUGGED from the outlet BEFORE connecting any DC wire to batteries or making any DC wiring connection change. Fail to do so may cause electrical shock resulting in serious personal injury or death. 1
3 Contents Introduction...3 Personal safety precautions...3 Precautions prior to charge battery...3 Box contents...4 Specifications...5 Special features:...8 Adaptive Loading Stage Smart Charge...8 Battery Check Warning...9 Battery Type Selector...10 Connection Check Warning...10 Safety features:...10 Ignition Protection...10 Overheat Protection...10 Over-Current Protection Over-Voltage Protection Reverse Polarity Protection Short Circuit Protection Installing the charger...12 Select battery type...13 Making DC connection...14 DC wiring connection charts: bank charger (M106/M108) bank charger (M208/M212/M220/M230) bank charger (M320/M330) bank charger (M430)...29 Operating the charger...46 Charge Status LED descriptions...46 LED indicator descriptions...47 Troubleshooting...49 Maintaining the charger...50 Warranty and service information...51 Contact information...51 Memo
4 Introduction INTRODUCTION Thank you and congratulations on your new purchase of the Powermania Turbo M series onboard battery charger. This charger is waterproof, corrosion-resistant and shock-resistant ideal for recharging and maintaining 12V DC batteries in marine applications and other harsh environments. Featuring Automatic 3-Stage Smart Charge and Battery Selector, this charger is designed to charge and maintain various types of 12V DC batteries using full automation. Our charging process has been proven to bring out the batteries full potential charge after each charging session while also extending their lifespan at the same time. The Turbo M also comes equipped with extensive safety features and intuitive LED indicators to help protect your investment, the charger itself, and its connected batteries and devices. PERSONAL SAFETY PRECAUTIONS 1. Someone should be within the voice range or close enough to come to your aid when working near a Lead-acid battery. Work in a well ventilated area away from ignition sources. 2. Have plenty of water and soap nearby in case battery acid comes in contact with skin, clothes, or eyes. 3. Wear complete eye protection and clothing protection. Avoid touching eyes while working near batteries. 4. If battery acid contacts skin or clothing, wash them immediately with water and soap. If acid enters eyes, immediately flood the eyes with running cold water for at least 10 minutes and get medical attention. Follow battery manufacturer s recommendations if you come in contact with acid. 5. Never smoke or allow open flame near batteries. 6. Do not drop a metal tool onto a battery as that may spark or short-circuit a battery and it may cause an explosion or fire. 7. Remove all personal metal items such as rings, bracelets, necklaces, and watches when working near batteries. A battery can cause short circuit currents that are high enough to weld metals and cause serious burns. PRECAUTIONS PRIOR TO CHARGE BATTERY Do not charge outside of battery manufacturer s recommended temperature conditions. Do not use this charger to charge dry cell batteries for home appliances. Do not operate the charger if any of the prewired cables or LED s is damaged. Make sure all onboard connected electronic devices are turned off. If a battery needs to be removed from the vehicle or boat to be charged, always remove the 3
5 Safety Precautions grounded negative terminal from the battery first. Be sure to have enough open space around the battery for good ventilation during charge. Gas can be forcefully blown away using a piece of cardboard or other non-metallic material as a fan. Wear full eye protection when cleaning battery terminals in case corrosive materials get in contact with eyes. Add distilled water in each cell until battery acid reaches levels specified by battery manufacturer. Do not overfill. For batteries without cell caps, please follow the recharging instructions provided by battery manufacturers. If necessary, use only industrial grade, UL approved extension cord connecting to the charger. When using extension cord, connect the charger end first before you plug the extension cord to a power outlet. When unplugging, unplug the end connecting to power outlet first, and then unplug the end connects to the charger. Make sure the AC power outlet you are connecting the charger to is GFCI (Ground Fault Circuit Interrupt) protected. BOX CONTENTS Turbo M series charger prewired with one AC power cord and DC output cable(s) Operation manual Registration card 4 x installation screws Replacement fuses: 1 x 10 Amp (Turbo M106) 1 x 10 Amp (Turbo M108) 2 x 10 Amp (Turbo M208) 2 x 15 Amp (Turbo M212) 2 x 25 Amp (Turbo M220) 2 x 35 Amp (Turbo M230) 3 x 25 Amp (Turbo M320) 3 x 35 Amp (Turbo M330) 4 x 35 Amp (Turbo M430) 4
6 Specifications SPECIFICATIONS M106 M108 M208 M212 Max. Input Current AC) 0.9 Amp 1.2 Amps 1.2 Amps 1.8 Amps Maximum Output 6 Amps 8 Amps 8 Amps 12 Amps # Output Bank (Prewired) Output Voltage Configuration 12V DC 12V DC 12/24V DC 12/24V DC Weight 5.2 lb. 5.2 lb. 5.6 lb. 5.6 lb. Dimension (Inch) 6 1 /2 x 4 1 /2 x 2 1 /2 6 1 /2 x 4 1 /2 x 2 1 /2 6 1 /2 x 4 1 /2 x 2 1 /2 6 1 /2 x 4 1 /2 x 2 1 /2 Recom. Battery Capacity* Ah Ah Ah Ah * All connected batteries combined 5
7 Specifications SPECIFICATIONS M220 M230 M320 M330 M Amps 4.3 Amps 2.9 Amps 4.3 Amps 4.3 Amps 20 Amps 30 Amps 20 Amp 30 Amps 30 Amps /24V DC 12/24V DC 12/24/36V DC 12/24/36V DC 12/24/36 48V DC 9.2 lb lb. 9.7 lb lb lb. 8 1 /4 x 5 3 /4 x 2 3 / /4 x 7 x 2 3 /4 8 1 /4 x 5 3 /4 x 2 3 / /4 x 7 x 2 3 / /4 x 7 x 2 3 / Ah Ah Ah Ah Ah 6
8 Specifications SPECIFICATIONS (All models) Nominal input voltage: 100V~240V AC Nominal input frequency: 50~60Hz Nominal output voltage/bank: 12V DC Power factor: 0.99 Efficiency: 84% Battery type setting: 1. Flooded (Lead-Acid) / AGM 2. GEL 3. AGM+ Max. Bulk time: 15 hours Max. Absorption time: 4 hours Operational temperature: -4 F ~ 122 F Storage temperature: -40 F ~185 F Output cable length: 6 feet / 182 cm Power cord length: 6 feet / 182 cm LED indicators: 1. Power 2. Charge status 3. Over-voltage / Overheat Indicator 4. Connection / Battery Check 5. AGM+ Charge Mode 6. GEL (Gel Cell) Charge Mode 7. Flooded (Lead-Acid)/AGM Charge Mode Special features: Adaptive Loading 3-Stage Smart Charge Battery Check Warning Battery Type Selector Connection Check Warning Safety features: Ignition Protection Overheat Protection Over-Current Protection Over-Voltage Protection Reverse Polarity Protection Short Circuit Protection Compliances: FCC Part 15 Class B (pending) CE (pending) IP65 (Splash-proof) Constructed in accordance to Marine UL
9 Special features SPECIAL FEATURE: Adaptive Loading (not applicable to M106/M108) USER BENEFIT: Fully charges all connected batteries in the shortest time. 10 A 2 A 10 A 18 A The Adaptive Loading feature dynamically adjusts the charger s output level on each output bank. More charging power is allocated to battery that is low in charge, and less charging power to battery that is closer to being fully charged. In Scenario 1 (left chart), the two batteries have similar charge levels. The Adaptive Loading feature allocates approximately equally 10 amps (50%) of its 20 amp output to each battery. In Scenario 2 (right chart), the first battery s is close to be fully charged while the second battery is discharged. The Adaptive Loading feature allocates only 2 amps (10%) to the first battery and the other 18 amps (90%) to the discharged one. Note that in both scenarios the charger utilizes its full output capacity (20 amps). In contrast to the other chargers with fixed output-per-bank constraints, the Turbo M charges all connected batteries to their fullest charge in the shortest time. SPECIAL FEATURE: 3-Stage Smart Charge USER BENEFIT: Maximizes battery potential and prolongs battery life. Turbo M charges battery in three sequential stages: Bulk, Absorption, and Float. This mechanism is proven to bring battery to its fullest charge, and also to maintain battery s full charge from self 8
10 Special features discharge. At the first stage (Bulk), the charger provides its maximum constant current to fast charge the battery. The battery s voltage rises as it absorbs the charge. When the battery voltage reaches 14.5V (Flooded mode*), it is about 80% recharged. The charger then moves to the second stage. At the second stage (Absorption), the charger continues to charge the battery at 14.5V (Flooded mode). The charging current slowly decreases as the battery charges up to 100%. When the battery is fully charged**, the charger then moves to the third stage. At the third stage (Float), the charging voltage is reduced to 13.4V (Flooded mode). The charger can be left connected to the battery indefinitely to maintain the battery s full charge. If the battery loses a significant amount of charge from usage, the charger will start a new recharge cycle. * Please refer to page 47 for voltage settings on each charge mode. ** Full charge is signified by two conditions: 1. The charger s output current drops to a minimal level. 2. The 4-hour Absorption period expires. If either one of these conditions are met, the charger will then move into the third stage (Float). SPECIAL FEATURE: Battery Check Warning USER BENEFIT: Warns user to check/replace defective battery. Warns user to turn off electronic devices. If the charger stays in the Bulk stage for more than 15 hours, it will escape from the Bulk stage, skip the Absorption stage, and move directly to the Float stage. However, in this scenario, the Charge Status LED will not display green as in a normal charging sequence. Instead, the Battery Check Warning LED will display solid yellow to warn user to check battery. This situation could be a result of defective battery cells or continuous current drawn from onboard electronic devices. 9
11 Special / Safety features SPECIAL FEATURE: Battery Type Selector USER BENEFIT: Compatible with various types of 12V batteries (Flooded Lead-Acid, AGM, High Power AGM, and GEL). The Battery Selector feature allows users to select different types of 12V batteries to charge. The initial factory setting is at Flooded Lead Acid/AGM charge mode. The other two charging modes are GEL charge mode and AGM+ charge mode. Select AGM+ charge mode when charging high power AGM batteries. Please refer to Table 1 on page 47 for different charge voltage settings at each charge mode. WARNING: DO NOT MIX TWO OR MORE BATTERY TYPES TO ONE CHARGER. ALWAYS CONNECT THE SAME TYPE AND SAME-AGED BATTERIES TO ONE CHARGER. SPECIAL FEATURE: Connection Check Warning USER BENEFIT: Alerts user if battery is not being charged. Warns user to check for broken fuses and loose cable connections. This feature helps ensure every battery is being charged. If the connection between the charger and the battery is broken, the Connection Check Warning LED will display blinking yellow. This may be the result of a blown fuse in one of the output cables. If any one set of output cables is left unconnected or if the connection is loose, the Connection Check Warning will also be triggered. SAFETY FEATURE: Ignition Protection USER BENEFIT: Eliminates fire sparks and prevents fire. The charger is encapsulated to prevent any internal spark from igniting external surroundings. Internal sparks may be potentially generated by misuse or component failure. SAFETY FEATURE: Overheat Protection USER BENEFIT: Protects charger from inadequate cooling environment. 10
12 Safety features The charger automatically shuts itself off if the ambient temperature rises above a safety threshold. This feature helps prevent damage to the charger from overheating. The charger will automatically turn itself on again once the ambient temperature drops to a safe level. SAFETY FEATURE: Over-Current Protection USER BENEFIT: Protects battery and charger from over-current damage. The charger limits itself to its maximum current output capacity. If a defective battery or its connected devices try to draw greater-than-provided current from the charger, the charger will prevent its charging current from exceeding the maximum output. SAFETY FEATURE: Over-Voltage Protection USER BENEFIT: Protects battery from incorrect DC wiring connections. The charger limits itself to the maximum of 16V DC output. The charger will shut off automatically if the battery s voltage is higher than 16V DC. This feature helps prevent damage to the battery due to unintended over-voltage supply from the charger. Over-voltage supply may be the result of incorrect DC wiring connections or defective battery. SAFETY FEATURE: Reverse Polarity Protection USER BENEFIT: Protects charger and battery from incorrect DC polarity wiring connections (positive to negative or vice versa). The charger is equipped with safety fuses on its output cables. If user incorrectly connects a positive output cable to a battery s negative terminal or vice versa, the fuse will be blown, thus disconnecting the charger and the battery. When replacing blown fuses, please replace with spare fuses provided with the charger or use fuses of the same rating and size. SAFETY FEATURE: Short Circuit Protection USER BENEFIT: Protects charger and battery from short circuit damages. This feature protects charger from sudden burst of excessive high current caused when a positive output ring terminal contacts a negative one.
13 Installation INSTALLING THE CHARGER The Powermania Turbo M series charger is designed to be mounted onboard. The chart below shows the proper orientation of the mounting position. The LED lights line up horizontally at the top and the output cables at the bottom. Select a well ventilated area where there are at least 8 inches of clear air space around the charger. Make sure the charger s output cables can reach all batteries from the mounting position. Do not mount the charger on carpeted, upholstered, or varnished surfaces. Make sure the mounting surface can firmly hold the charger with the provided screws. Place charger on the tentative mounting area. Use a pencil to mark position of each mounting hole. Use 1/8 drill bit to drill on the marked position. Align the charger to the drilled holes, and then secure the charger with provided screws. 12
14 Installation SELECT BATTERY TYPE The Battery Selector s tip point can be switched among three positions as follows. From left to right, the first position (factory default) is for charging Flooded Lead-Acid type and AGM type battery. The middle position is for charging GEL (Gel Cell) type battery, and the right position is for charging High Power AGM type battery. Please refer to Table 1 on page 47 for voltage settings in each charge mode. L. Acd AGM GEL AGM+ To switch to a different charge mode, please follow these steps: 1. Make sure the charger s power cord is unplugged from the power outlet. 2. Loosen the screws from the battery selector. 3. Pull the battery selector straight out from the charger. 4. Place the battery selector back to the charger with the desired position. 5. Secure the screws back to the battery selector. CAUTION: RISK OF PERSONAL INJURY The screws used to secure the battery selector must be 10mm or shorter. If the screws are longer than 10mm, the charger could be damaged and could result in serious personal injury. 13
15 DC wiring connections MAKING DC CONNECTION The following pages (p.15 - p.45) demonstrate proper DC wiring configurations for Powermania Turbo M series chargers. When making DC connections, make sure each set of output cables (one positive and one negative) is connected to the same battery set of terminals. The red wires are positive (shown as grey color on the charts) and the black ones are negative. Never connect a black wire (negative) to a terminal that is connected with a red wire (positive). Always connect ALL of the charger s output cables to battery terminal(s). NEVER LEAVE ANY SET OF OUTPUT CABLES UNCONNECTED. The charger will display blinking yellow on the Connection Check LED if any output cable is not connected to battery terminal. It is recommended to CONNECT THE CHARGER S FIRST OUTPUT SET (OUTPUT 1) TO MAIN HOUSE BATTERY. The first output set is located next to the AC cord. Please refer to the following legend reference used on the connection charts: Fuse holder Positive output (Red wire) Negative output (Black wire) Jumper cable (not included) AC input power cord 14
16 Output 1 DC wiring connections Connection 1A: Connecting 1-bank charger (M106/M108) to one independent 12V battery. 15
17 Output 1 DC wiring connections Connection 2A: Connecting 2-bank charger (M208/M212/M220/M230) to one independent 12V battery. 16
18 Output 1 DC wiring connections Connection 2B: Connecting 2-bank charger (M208/M212/M220/M230) to two independent 12V batteries. 17
19 Output 1 DC wiring connections Connection 2C: Connecting 2-bank charger (M208/M212/M220/M230) to two serial-connected 12V batteries (24V). 18
20 Output 1 DC wiring connections Connection 2D: Connecting 2-bank charger (M208/M212/M220/M230) to two parallel-connected 12V batteries. 19
21 Output 1 Output 3 DC wiring connections Connection 3A: Connecting 3-bank charger (M320/M330) to one independent 12V battery. 20
22 Output 1 Output 3 DC wiring connections Connection 3B: Connecting 3-bank charger (M320/M330) to two independent 12V batteries. 21
23 Output 1 Output 3 DC wiring connections Connection 3C: Connecting 3-bank charger (M320/M330) to two serial-connected 12V batteries (24V). 22
24 Output 1 Output 3 DC wiring connections Connection 3D: Connecting 3-bank charger (M320/M330) to two parallel-connected 12V batteries. 23
25 DC wiring connections Connection 3E: Connecting 3-bank charger (M320/M330) to three independent 12V batteries. Output 1 Output 3 24
26 DC wiring connections Connection 3F: Connecting 3-bank charger (M320/M330) to one independent and two serial-connected 12V batteries (24V). Output 1 Output 3 25
27 DC wiring connections Connection 3G: Connecting 3-bank charger (M320/M330) to one independent and two parallel-connected 12V batteries. Output 1 Output 3 26
28 DC wiring connections Connection 3H: Connecting 3-bank charger (M320/M330) to three serial-connected 12V batteries (36V). Output 1 Output 3 27
29 DC wiring connections Connection 3I: Connecting 3-bank charger (M320/M330) to three parallel-connected 12V batteries. Output 1 Output 3 28
30 Output 1 Output 3 Output 4 DC wiring connections Connection 4A: Connecting 4-bank charger (M430) to one independent 12V battery. 29
31 Output 1 Output 3 Output 4 DC wiring connections Connection 4B: Connecting 4-bank charger (M430) to two independent 12V batteries. 30
32 Output 1 Output 3 Output 4 DC wiring connections Connection 4C: Connecting 4-bank charger (M430) to two serial-connected 12V batteries (24V). 31
33 Output 1 Output 3 Output 4 DC wiring connections Connection 4D: Connecting 4-bank charger (M430) to two parallel-connected 12V batteries. 32
34 Output 1 Output 3 Output 4 DC wiring connections Connection 4E: Connecting 4-bank charger (M430) to three independent 12V batteries. 33
35 Output 1 Output 3 Output 4 DC wiring connections Connection 4F: Connecting 4-bank charger (M430) to one independent and two serial-connected 12V batteries (24V). 34
36 Output 1 Output 3 Output 4 DC wiring connections Connection 4G: Connecting 4-bank charger (M430) to three serial-connected 12V batteries (36V). 35
37 Output 1 Output 3 Output 4 DC wiring connections Connection 4H: Connecting 4-bank charger (M430) to one independent and two parallel-connected 12V batteries. 36
38 Output 1 Output 3 Output 4 DC wiring connections Connection 4I: Connecting 4-bank charger (M430) to three parallel-connected 12V batteries. 37
39 DC wiring connections Connection 4J: Connecting 4-bank charger (M430) to four independent 12V batteries. Output 1 Output 3 Output 4 38
40 DC wiring connections Connection 4K: Connecting 4-bank charger (M430) to two independent and two serial-connected 12V batteries (24V). Output 1 Output 3 Output 4 39
41 DC wiring connections Connection 4L: Connecting 4-bank charger (M430) to one independent and three serial-connected 12V batteries (36V). Output 1 Output 3 Output 4 40
42 DC wiring connections Connection 4M: Connecting 4-bank charger (M430) to two serial-connected (24V) and two parallel-connected 12V batteries. Output 1 Output 3 Output 4 41
43 DC wiring connections Connection 4N: Connecting 4-bank charger (M430) to four serial-connected 12V batteries (48V). Output 1 Output 3 Output 4 42
44 DC wiring connections Connection 4O: Connecting 4-bank charger (M430) to two independent and two parallel-connected 12V batteries. Output 1 Output 3 Output 4 43
45 DC wiring connections Connection 4P: Connecting 4-bank charger (M430) to one independent and three parallel-connected 12V batteries. Output 1 Output 3 Output 4 44
46 DC wiring connections CONNECT ALL DC OUTPUT CABLES TO BATTERY TERMINALS TO AVOID SETTING OFF CONNECTION WARNING Connection 4Q: Connecting 4-bank charger (M430) to four parallel-connected 12V batteries. Output 1 Output 3 Output 4 45
47 Operating instructions OPERATING THE CHARGER 1. Install the charger and make appropriate DC wiring connections. 2. Choose appropriate setting on the Battery Selector. 3. Plug in AC power cord to properly grounded outlet. 4. The Power indicator LED will display green, indicating the presence of AC power. 5. The charger will automatically start a new charge cycle. CHARGE STATUS LED DESCRIPTION Charge Status LED Display Solid Red Blinking Red Description Battery is discharged. The charger is recharging battery in the first stage (Bulk). At this stage, the charger provides its maximum constant current. The battery absorbs the charge and its voltage rises to a specific level (Uo) set by the charge mode.* Once Uo is reached, the charger will then move into the second stage (Absorption). If Uo cannot be reached after 15 hours of uninterrupted charge in the Bulk stage, the charger will time out and skip to the third stage (Float). In this case, the Battery Check Indicator LED will display solid yellow. (Please see Troubleshooting.) Battery is about 80% charged. The charger is recharging battery in the second stage (Absorption). At this stage, the charger continues to charge battery at the constant voltage (Uo). The charging current slowly decreases as the battery charges up to 100%. Full charge is signified by two conditions: 1. The charger s output current drops to a minimal level. 2. The 4-hour Absorption period expires. If either one of these condition is met, the charger will then move into the third stage (Float). * Please refer to Table 1 on page 47 for voltage settings in each charge mode. 46
48 Operating instructions Charge Status LED Display Solid Green Description Battery is fully charged. The charger is maintaining battery from selfdischarge in the third stage (Float). At this stage, the charging voltage is reduced to a lower level set by the charge mode. The charger can be left connected to the battery indefinitely to maintain the battery s full charge. Meanwhile, the charger can also provide its maximum output current for external DC loads, in which case the charger would function as a power supply. If the external DC loads cause the regulated voltage to drop below 12.5V DC, the charger will start a new charge cycle. Table 1. Battery Voltage Settings Charge Mode Voltage (Absorption) Voltage (Float) L. Acd AGM Flooded (Lead-Acid) / AGM 14.5V DC 13.4V DC GEL GEL 14.1V DC 13.8V DC AGM+ AGM+* 14.7V DC 13.6V DC * AGM+ Mode is designed for charging High Power AGM batteries LED INDICATOR DESCRIPTION Icon Indicator Description POWER GREEN: Power On 47
49 Operating instructions LED INDICATOR DESCRIPTION Icon Indicator Description CHARGE STATUS: SOLID RED: Bulk stage BLINKING RED: Absorption stage GREEN: Float stage OVER-VOLTAGE / OVERHEAT INDICATOR BLINKING YELLOW: Voltage exceeds range SOLID YELLOW: Temperature exceeds range CONNECTION CHECK / BATTERY CHECK INDICATOR BLINKING YELLOW: Check fuse / DC connections SOLID YELLOW: Check battery AGM+ AGM+ CHARGE MODE GREEN: Charging in AGM+ mode GEL GEL CHARGE MODE GREEN: Charging in GEL mode L. Acd AGM FLOODED(LEAD-ACID) / AGM CHARGE MODE GREEN: Charging in Flooded (Lead-Acid)/ AGM Mode 48
50 Troubleshooting DANGER: ALWAYS DISCONNECT AC POWER CORD PRIOR TO MAKING ANY DC WIRING CONNECTION CHANGE OR CHECKING FUSE. TROUBLESHOOTING Problem Possible Cause Solution Power indicator GREEN LED is not on. Overheat indicator LED displays SOLID YELLOW Over-Voltage indicator LED displays BLINKING YELLOW Battery Check indicator LED displays SOLID YELLOW (Charger remains in Bulk stage for more than 15 hours.) No AC input. Short circuit at DC output. Ambient temperature exceeds safe range.** Battery voltage exceeds safe range. One or more defective battery cells. Battery is continuously drawing charge. Battery system capacity exceeds charger s range. Check AC input connection. Make sure AC power is present. Check and correct battery wiring connection (Refer to wiring connection charts). Replace broken fuse if necessary.* Remove any objects obstructing airflow around the charger. Wait for the charger to cool down. Charge will start when the ambient temperature drops to the safe range. Check and correct battery wiring connection. (Refer to wiring connection charts.) Wait at least 30 seconds before plugging in AC power again. If Over-Voltage LED continues to display blinking yellow even with correct wiring connections, unplug the charger s AC power input and stop using the charger to avoid possible damage to the battery and/or connected electronic devices. Run battery test and replace defective battery. Turn off all electronic devices that might be drawing charge from battery. Reconfigure battery system to reduce its total Ah (Amp Hour) rating within the charger s recommended Ah capacity. 49
51 Troubleshooting DANGER: ALWAYS DISCONNECT AC POWER CORD PRIOR TO MAKING ANY DC WIRING CONNECTION CHANGES OR CHECKING FUSES. Problem Possible Cause Solution Connection Check indicator LED displays BLINKING YELLOW One or more outputs are not connected to a battery terminal. Fuse failure. Faulty terminal connections. Reverse polarity on DC wiring connections. Make sure all charger outputs are properly connected to battery terminals. (Refer to wiring connection charts.) Check for blown fuses on output cables and replace damaged fuses.* Clean battery terminals and tighten all wiring connections. Correct connections with matching polarity. Check fuses on output cables and replace any damaged fuses.* * When replacing blown fuses, please replace with spare fuses provided with the charger or use fuses of the same rating and size. Please contact Powermania for more information on the replacement fuses. ** The operational ambient temperate range is -4 F~122 F (-20 C~50 C). When the ambient temperature rises outside the range during operation, the charger s Overheat LED will display solid yellow and the charger will be shut off automatically. Once the ambient temperature cools down to a safe range, the charger will be turned on again automatically. MAINTAINING THE CHARGER The Powermania Turbo M charger requires no specific maintenance. However, it is recommended to do the following to ensure reliable and optimal performance from your battery: Regularly clean battery terminals and charger s output ring terminals with baking soda and tighten all DC wiring connections. Regularly check and maintain proper battery electrolyte level following battery manufacturer s instructions. It is recommended that you keep the charger s power on to maintain the connected batteries during long storage periods. This method has been proven to extend battery life. 50
52 Other information WARRANTY AND SERVICE INFORMATION Powermania, at its discretion, provides 2-year limited warranty on Turbo M chargers against defects in material or workmanship under normal use. The warranty coverage period is calculated as follows: If customer provides a valid purchase receipt, the 2-year period is calculated from the date of purchase. If customer cannot provide a valid purchase receipt, the 2-year period is calculated from the manufacture date based on serial number. The following conditions are NOT covered under warranty: Physical damage Normal wear and tear Damage caused by accidents, misuse, or alteration of the product. 51
SAVE THESE INSTRUCTIONS
R MODEL 2611 10 AMP ON BOARD BATTERY CHARGER Two Outputs OWNER S MANUAL Connections at a glance: For the best charging results both 12 Volt independent batteries should be equally discharged. The charger
More informationMODEL 2602A-12 3 STAGE AUTOMATIC BATTERY CHARGER OWNER S MANUAL SAVE THESE INSTRUCTIONS
R A Valley Forge Company MODEL 2602A-12 3 STAGE AUTOMATIC BATTERY CHARGER OWNER S MANUAL SAVE THESE INSTRUCTIONS 1. INTRODUCING THE CHARGER The 2602A-12 is a 3-stage electronic battery charger. Rainproof,
More informationCruising Charger Series OWNER S MANUAL
R Cruising Charger Series OWNER S MANUAL ON BOARD BATTERY CHARGERS Models DC Amperage No. Of Banks Volts 2614A 5,10 Amps 2 Bank 12/12 2614A-230 2621A 5,5,10 Amps 3 Banks 12/12/12 2621A-230 2622A 10,10
More informationIntelligent Charging System Series
R Intelligent Charging System Series OWNER S MANUAL ON BOARD BATTERY CHARGERS Models Amperage No. Of Banks Volts 16061 s 1 Bank 12 16102 6,s 2 Banks 12 or 24 16153 6,6,s 3 Banks 12 or 24 or 36 16202 10,10
More informationAC CONVERTER / BATTERY CHARGER
AC CONVERTER / BATTERY CHARGER User s Manual MODEL #: CON120AC12/24VDC Listed to UL 458 and CSA 22.2 NO. 107.1 Standards Contents INTRODUCTION... 3 Important Safety Instructions... 3 1. General Description...
More informationINTELLIGENT BATTERY CHARGER/MAINTAINER
INTELLIGENT BATTERY CHARGER/MAINTAINER OWNER S MANUAL Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More information12V 1 AMP (1000 ma) Automatic Battery Charger & Maintainer
12V 1 AMP (1000 ma) Automatic Battery Charger & Maintainer For lead-acid batteries THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR 12V BATTERY CHARGER: YUA1201000 / INT1201000 KEEP
More information10 AMP ON BOARD BATTERY CHARGER
R A Valley Forge Company MODEL 2611A-1-B 10 AMP ON BOARD BATTERY CHARGER One Output OWNER S MANUAL IMPORTANT! READ THESE INSTRUCTIONS BEFORE INSTALLING AND USING THIS PRODUCT. Keep these instructions for
More informationInstallation and Operating Instructions (for chargers shown below)
Installation and Operating Instructions (for chargers shown below) For additional information please call our Technical Support Group 800.742.2740 PRO CHARGING SYSTEMS, LLC 1551 Heil Quaker Boulevard,
More information2603 Battery Pal 3 AMP, 1 2 VOLT BATTERY CHARGER
R 2603 Battery Pal 3 AMP, 1 2 VOLT BATTERY CHARGER Connections at a glance: The GUEST Battery Pal 2603 is designed to recharge your battery, and extend your battery s life in applications where it is stored
More informationSafety, Installation And Operating Instructions For The Following Battery Charger Models: i2412, i3612, i4809, i2425, i3625, and i4818
Safety, Installation And Operating Instructions For The Following Battery Charger Models: i2412, i3612, i4809, i2425, i3625, and i4818 IMPORTANT NOTICE: Please save and read these safety, operating and
More informationOPERATOR'S MANUAL IMPORTANT SAFETY INSTRUCTIONS
ASSOCIATED OPERATOR'S MANUAL IMPORTANT SAFETY INSTRUCTIONS MODEL 6366 12 VOLT, 0-20 AMP 4 X 20 BATTERY CHARGER 1. SAVE THESE INSTRUCTIONS. This manual contains important safety and operating instructions
More informationinstallation and operating instructions for the following xtreme Battery chargers:
installation and operating instructions for the following xtreme Battery chargers: Model Name No. of Banks Amps Per Bank Battery System Dual Pro SE Xtreme Dual Pro Xtreme Three Bank SE Xtreme Three Bank
More informationAUTO CHARGE 11 MODEL #: XX. AUTOMATIC BATTERY CHARGER U.L. Configuration INSTRUCTION MANUAL
INSTRUCTION MANUAL AUTO CHARGE 11 AUTOMATIC BATTERY CHARGER U.L. Configuration MODEL #: 091-11-XX NOTE : This charger is designed for vehicles with dual batteries and negative ground. CAUTION This unit
More informationMODEL 6010A 6 12 VOLT BATTERY CHARGER ASSOCIATE
MODEL 600A 6 VOLT BATTERY CHARGER ASSOCIATE IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. This manual contains important safety and operating instructions for the battery charger you have purchased.
More informationOWNER S MANUAL. Model YUA2AMPCH 2 AMP Dual-Bank Automatic Battery Charger & Maintainer READ ENTIRE MANUAL BEFORE USING THIS PRODUCT
Model YUA2AMPCH 2 AMP Dual-Bank Automatic Battery Charger & Maintainer Certified by California BCS Regulations OWNER S MANUAL READ ENTIRE MANUAL BEFORE USING THIS PRODUCT READ ENTIRE MANUAL BEFORE USING
More informationInstallation and Operating Instructions (for chargers shown below)
Installation and Operating Instructions (for chargers shown below) For additional information please call our Technical Support Group 800.742.2740 PRO CHARGING SYSTEMS, LLC 1551 Heil Quaker Boulevard,
More informationIMPORTANT SAFETY INSTRUCTIONS IMPORTANT: READ AND SAVE THIS SAFETY AND INSTRUCTION MANUAL. KEEP IT WITH OR NEAR CHARGER AT ALL TIMES.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT: READ AND SAVE THIS SAFETY AND INSTRUCTION MANUAL. KEEP IT WITH OR NEAR CHARGER AT ALL TIMES. SPECIFICATIONS: For technical assistance, call your Dealer with the
More informationGo Power! Manual. GP-Smart Charger
Go Power! Manual GP-Smart Charger Go Power! Electric Inc. PO Box 6033 Victoria, BC V8P 5L4 Toll Free Tel: 866-247-6527 Toll Free Fax: 866-607-6527 Email: info@gpelectric.com Table of Contents 1. IMPORTANT
More informationMODEL 6017 OPERATOR'S MANUAL
MODEL 6017 OPERATOR'S MANUAL ASSOCIATE D IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS. This manual contains important safety and operating instructions for the battery charger you have purchased.
More informationCRS1, CRS2 and CRS3. For additional information please call our. PRO CHARGING SYSTEMS, LLC 1551 Heil Quaker Boulevard, LaVergne, TN
CRS1, CRS2 and CRS3 For additional information please call our Technical Support Group 800.742.2740 PRO CHARGING SYSTEMS, LLC 1551 Heil Quaker Boulevard, LaVergne, TN 37086-3539 110310 Installation and
More information10AMP FULLY AUTOMATIC 6V & 12V BATTERY CHARGER OWNER'S MANUAL
1244502 10AMP FULLY AUTOMATIC 6V & 12V BATTERY CHARGER OWNER'S MANUAL 1. IMPORTANT SAFETY INSTRUCTIONS 1.1 SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions. 1.2
More informationSP6. Automatic Battery Charger. Model
Model SP6 Automatic Battery Charger OWNERS MANUAL PLEASE SAVE THIS OWNERS MANUAL AND READ BEFORE EACH USE. This manual will explain how to use the charger safely and effectively. Please read and follow
More informationInstallation and Operating Instructions (for chargers shown below)
Installation and Operating Instructions (for chargers shown below) For additional information please call our Technical Support Group 800.742.2740 PRO CHARGING SYSTEMS, LLC 1551 Heil Quaker Boulevard,
More informationModels: SP3, SPSS3 Automatic Battery Charger
OWNERS MANUAL Models: SP3, SPSS3 Automatic Battery Charger PLEASE SAVE THIS OWNERS MANUAL AND READ BEFORE EACH USE. This manual will explain how to use the charger safely and effectively. Please read and
More informationAUTO CHARGE 4000 MODEL #: LOW PROFILE CHARGER AUTOMATIC DUAL OUTPUT BATTERY CHARGER INSTRUCTION MANUAL
INSTRUCTION MANUAL AUTO CHARGE 4000 LOW PROFILE CHARGER AUTOMATIC DUAL OUTPUT BATTERY CHARGER Unit supplied with this display MODEL #: 091-89-12 INPUT: 120 Volt, 50/60 Hz, 5 Amps OUTPUT: 45 Amps File:
More informationPUMP PLUS 2000 PLC MODEL #: PP AUTOMATIC DUAL OUTPUT BATTERY CHARGER INSTRUCTION MANUAL
INSTRUCTION MANUAL PUMP PLUS 2000 PLC AUTOMATIC DUAL OUTPUT BATTERY CHARGER Supplied with Dual Bar Graph Display MODEL #: 091-237-12-PP INPUT: 120 Volt, 60 Hz, 3.5 Amps OUTPUT BATTERY 1 and 2: 15 or 18
More information2/10/50 AMP 12 VOLT BATTERY CHARGER/ ENGINE STARTER
2/10/50 AMP 12 VOLT BATTERY CHARGER/ ENGINE STARTER WARNING This product contains or, when used, produces a chemical known to the State of California to cause cancer and birth defects or other reproductive
More informationINSTRUCTION MANUAL. 12-Station HD Shop 12V Portable Battery Charger
INSTRUCTION MANUAL 12-Station HD Shop 12V Portable Battery Charger IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions for your HD
More information801 BUSINESS CENTER DRIVE MOUNT PROSPECT, ILLINOIS Ext. 322
277-999 ELECTRIC CORP. 801 BUSINESS CENTER DRIVE MOUNT PROSPECT, ILLINOIS 800-621-5485 Ext. 322 Send Warranty Product Repairs to: 605 South Vermilion, Suite C, Brownsville, TX 78521-6851 Call Customer
More informationDigital Mobile Charge Advanced Electronic In-Transit 4-Stage Battery to Battery Charger
Digital Mobile Charge Advanced Electronic In-Transit 4-Stage Battery to Battery Charger Owner s Manual and Installation Guide Model Part Number Description Digital Mobile Charge 05502 Advanced In-Transit
More informationAUTO CHARGE 12 AUTOMATIC BATTERY CHARGER
INSTRUCTION MANUAL FILE: 091-165-12 reve Rev: E, page 8 DATE: 7-02-15 AUTO CHARGE 12 AUTOMATIC BATTERY CHARGER MODEL #091-165-12 NOTE : This charger is designed for vehicles with a single battery and negative
More informationIMPORTANT SAFETY INSTRUCTIONS
1163714 1.5 AMP 12VOLT TRICKLE 1.5 AUTOMATIC AMP AUTOMATIC TRICKLE 1.5 AMP AUTOMATIC 12V12VOLT BATTERY CHARGER IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS This product offers a wide range
More information12V/25A BATTERY CHARGER MAINTAINER / JUMPSTARTER
12V/25A BATTERY CHARGER MAINTAINER / JUMPSTARTER OWNER S MANUAL Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic
More information801 BUSINESS CENTER DRIVE MOUNT PROSPECT, ILLINOIS
280-600 Send Warranty Product Repairs to: 1025 E. Thompson Ave., Hoopeston, IL 60942-0280. Call Customer Service if you have questions: 1-800-621-5485 A. IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS
More informationBATTERY CHARGER CHR-1445
BATTERY CHARGER CHR-1445 / 2685 TEL:886-4-2238-0698 FAX:886-4-2238-0891 Web Site:http://www.monicon.com.tw E-mail:sales@monicon.com.tw Copyright 2007 Monicon Instruments Co., Ltd. All right reserved. Contents
More informationAUTO CHARGE D PUMP PLUS
INSTRUCTION MANUAL AUTO CHARGE D PUMP PLUS AUTOMATIC DUAL OUTPUT BATTERY CHARGER Designed Specifically for Vehicles with DDEC ENGINES MODEL #: 091-9-DPP INPUT: 120 Volt, 60 Hz, 8 Amps OUTPUT VEHICLE BATTERY:
More informationAUTO CHARGE D2 MODEL #: AUTOMATIC TRIPLE OUTPUT BATTERY CHARGER INSTRUCTION MANUAL
INSTRUCTION MANUAL AUTO CHARGE D2 AUTOMATIC TRIPLE OUTPUT BATTERY CHARGER Designed Specifically for Vehicles with DDEC ENGINES MODEL #: 091-74-12 INPUT: 120 Volt, 60 Hz, 8 Amps OUTPUT VEHICLE BATTERY 1
More informationPSJ-2212, PSJ-3612, PSJ-4424
Model: PSJ-2212, PSJ-3612, PSJ-4424 Jump Starter and DC Power Source OWNER S MANUAL PSJ-2212 PLEASE SAVE THIS OWNER S MANUAL AND READ BEFORE EACH USE. This manual will explain how to use your jump starter
More informationPUMP PLUS 1000 PLC MODEL #: PP AUTOMATIC SINGLE OUTPUT BATTERY CHARGER INSTRUCTION MANUAL
INSTRUCTION MANUAL PUMP PLUS 1000 PLC AUTOMATIC SINGLE OUTPUT BATTERY CHARGER Unit supplied with one of these displays MODEL #: 091-215-12-PP INPUT: 120 Volt, 60 Hz, 3.5 Amps OUTPUT BATTERY 1 and 2: 15
More informationAUTO CHARGE 12 HO MODEL #: MODEL #: MODEL #: AUTOMATIC SINGLE OUTPUT BATTERY CHARGER INSTRUCTION MANUAL
INSTRUCTION MANUAL AUTO CHARGE 12 HO AUTOMATIC SINGLE OUTPUT BATTERY CHARGER MODEL #: 091-170-6 MODEL #: 091-170-12 MODEL #: 091-170-24 File: IM_091-170-xx_revd.indd Rev: D Revised By: MFG Date: 10-23-2013
More informationOperating Instructions
Operating Instructions PRO- If you sell, inventory or service lead-acid batteries, you want the battery you take off the shelf to be as new as the day it was manufactured. However, batteries that sit idle
More informationLPC 20 MODEL #: LOW PROFILE CHARGER AUTOMATIC SINGLE OUTPUT BATTERY CHARGER INSTRUCTION MANUAL
INSTRUCTION MANUAL LPC 20 LOW PROFILE CHARGER AUTOMATIC SINGLE OUTPUT BATTERY CHARGER Unit supplied with one of these displays MODEL #: 091-207-12 INPUT: 120 Volt, 50/60 Hz, 7 Amps OUTPUT: 20 Amps File:
More informationBatteryMINDer 1500* & BatteryMINDer Plus 1510*
BatteryMINDer 1500* & BatteryMINDer Plus 1510* both with SmarTECHnology 12 Volt 1500 ma Charger - Maintainer - Desulfator INCLUDES: Auto-Temp Compensation Sensor, installed (1500 & 1510) Optional Permanent
More informationDeltran Battery Tender 6V/12V 4Amp 5 & 10 Bank Battery Management System TABLE 1. Length of Cord, Feet AWG Size of Cord
Deltran Battery Tender 6V/12V 4Amp 5 & 10 Bank Battery Management System Designed for Six-cell and three-cell Flooded/AGM/GEL Lead-Acid Batteries and Four-Cell Lithium Iron Phosphate (LiFePO4) Batteries
More informationModel: SE-4020-CA Automatic Battery Charger
OWNERS MANUAL Model: SE-4020-CA Automatic Battery Charger PLEASE SAVE THIS OWNERS MANUAL AND READ BEFORE EACH USE. This manual will explain how to use the battery charger safely and effectively. Please
More informationAUTO CHARGE 4000 MODEL #: AUTOMATIC DUAL OUTPUT BATTERY CHARGER INSTRUCTION MANUAL. Ph: Fax:
INSTRUCTION MANUAL AUTO CHARGE 4000 AUTOMATIC DUAL OUTPUT BATTERY CHARGER MODEL #: 091-89-12 INPUT: 120 Volt, 50/60 Hz, 8 Amps OUTPUT BATTERY CHARGER: 40 Amps OUTPUT BATTERY SAVER: 5 Amps File: IM_091-89-12_reve.indd
More informationBK10 10 CHANNELS BANK CHARGER For 12V lead-acid batteries
BK10 10 CHANNELS BANK CHARGER For 12V lead-acid batteries DESIGNED FOR WORKSHOPS AND WAREHOUSES User Manual and Guide to professional battery charging for Starter and Deep Cycle batteries. THIS MANUAL
More informationLPC 40 MODEL #: LOW PROFILE CHARGER WITH PLC AUTOMATIC SINGLE OUTPUT BATTERY CHARGER INSTRUCTION MANUAL
INSTRUCTION MANUAL LPC 40 LOW PROFILE CHARGER WITH PLC AUTOMATIC SINGLE OUTPUT BATTERY CHARGER Unit supplied with one of these displays MODEL #: 091-200-12 INPUT: 120 Volt, 50/60 Hz, 5 Amps OUTPUT: 40
More informationArt. No. EC-315. Art. No. EC-330. Art. No. EC-340 SWITCH-MODE BATTTERY CHARGER CONTENTS IMPORTANT SAFETY PRECAUTIONS... 2
SWITCH-MODE BATTTERY CHARGER CONTENTS IMPORTANT SAFETY PRECAUTIONS... 2 DESCRIPTION AND FEATURES... 3 CHARGING STAGES... 4 Art. No. EC-315 Art. No. EC-330 Art. No. EC-340 PROTECTIONS... 5 INSTALLATION...
More informationAutomatic Battery Charger Switching mode with Micro-controlled Input: Vac / Output: 12Volt DC
Automatic Battery Charger Switching mode with Micro-controlled Input:100-140Vac / Output: 12Volt DC User s Manual and Important Safety Information Model: #20085 (SW121080-06) FEATURES Congratulations on
More informationAutomatic Battery Charger Switching mode with Micro-controlled Input: Vac / Output: 12Volt DC
Automatic Battery Charger Switching mode with Micro-controlled Input:220-260Vac / Output: 12Volt DC User s Manual and Important Safety Information Model: OC-SW121080 / OC-SW121160 / OC-SW121210 FEATURES
More information12 VOLT 30 AMP DIGITAL SOLAR CHARGE CONTROLLER
12 VOLT 30 AMP DIGITAL SOLAR CHARGE CONTROLLER User s Manual Congratulations on your Coleman solar product purchase. This product is designed to the highest technical specifications and standards. It will
More information12 Volt 1500 ma Convertible Charger - Maintainer - Desulfator*
1215C 12 Volt 1500 ma Convertible Charger - Maintainer - Desulfator* INCLUDES: Auto-Temp Compensation Sensor, installed Optional Permanent Mounting Brackets and screws Battery Clips (Fully-Insulated 6
More informationBATTERY SAVER LOW RIPPLE HO
INSTRUCTION MANUAL BATTERY SAVER LOW RIPPLE HO LOW RIPPLE POWER SUPPLY / AUTOMATIC LOAD SWITCH FOR 12VDC VEHICLE SYSTEMS MODEL #: 091-195-12 INPUT: 120 Volt, 50/60 Hz, 4.5 Amps RMS OUTPUT: 13.2 Volts DC,
More informationAutomatic Battery Charger Switching mode with Micro-controlled Input: Vac / Output: 12Volt DC
Automatic Battery Charger Switching mode with Micro-controlled Input:220-260Vac / Output: 12Volt DC User s Manual and Important Safety Information Model: OC-SW121080 / OC-SW121160 / OC-SW121210 FEATURES
More informationOWNERS MANUAL Models: XP400, XP500, XP750C INSTANT POWER Jump Starter and DC Power Source
OWNERS MANUAL Models: XP400, XP500, XP750C INSTANT POWER Jump Starter and DC Power Source XP400 XP500 XP750C PLEASE SAVE THIS OWNER S MANUAL AND READ BEFORE EACH USE. This manual will explain how to use
More informationAUTO CHARGE DUAL MODEL #: AUTOMATIC DUAL OUTPUT BATTERY CHARGER INSTRUCTION MANUAL. Ph: Fax:
INSTRUCTION MANUAL AUTO CHARGE DUAL AUTOMATIC DUAL OUTPUT BATTERY CHARGER MODEL #: 091-145-12 INPUT: 120 Volt, 50/60 Hz, 3.5 Amps OUTPUT BAT 1: 10 Amps OUTPUT BAT 2: 10 Amps File: IM_091-145-12_revb.indd
More informationManual. EN Appendix. Blue Smart IP65 Charger 120V 12/7 12/10 12/15 24/8
Manual EN Appendix Blue Smart IP65 Charger 120V 12/7 12/10 12/15 24/8 IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions for Blue
More informationUser s Manual. Automatic Switch-Mode Battery Charger
User s Manual Automatic Switch-Mode Battery Charger IMPORTANT Read, understand, and follow these safety rules and operating instructions before using this battery charger. Only authorized and trained service
More informationBC12M248 7 Stage Automatic Smart Battery Charger, Desulfator & Maintainer 12V, 2 / 4 / 8A FOR AGM, GEL AND WET BATTERIES USER MANUAL
BC12M248 7 Stage Automatic Smart Battery Charger, Desulfator & Maintainer 12V, 2 / 4 / 8A FOR AGM, GEL AND WET BATTERIES USER MANUAL THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS 1 IMPORTANT
More information7 Stage Automatic Smart Battery Charger (FOR CHARGING 12V / 24V AGM, GEL,SLA AND WET BATTERIES) USER MANUAL
7 Stage Automatic Smart Battery Charger Desulphuration& Maintainer (FOR CHARGING 12V / 24V AGM, GEL,SLA AND WET BATTERIES) USER MANUAL THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS 1
More information400 Watt Backup Power System Owner s Manual
400 Watt Backup Power System Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More informationOPERATOR S MANUAL JUMP STARTER. and DC Power Source. Model No CAUTION: Sears, Roebuck and Co., Hoffman Estates, IL U.S.A.
OPERATOR S MANUAL JUMP STARTER and DC Power Source Model No. 71489 CAUTION: Read and follow all Safety Rules and Operating Instructions before Every Use of this Product. SAVE THESE INSTRUCTIONS. Sears,
More informationHigh Frequency SMT Golf Car Chargers Battery Tender Battery Charger Models: 12 Volt 20 Amp, 24 Volt 20 Amp, 36 Volt 15 Amp, 48 Volt 10 Amp
Deltona Transformer Corporation High Frequency SMT Golf Car Chargers Battery Tender Battery Charger Models: 12 Volt 20 Amp, 24 Volt 20 Amp, 36 Volt 15 Amp, 48 Volt 10 Amp IMPORTANT SAFETY INSTRUCTIONS
More informationCONGRATULATIONS ON YOUR PURCHASE OF YOUR THUNDER BATTERY CHARGER! For your personal safety read, understand and follow the information provided in
CONGRATULATIONS ON YOUR PURCHASE OF YOUR THUNDER BATTERY CHARGER! For your personal safety read, understand and follow the information provided in this instruction manual & on the battery charger. This
More informationOwner's Manual and Installation Guide
ProMariner ProMariner ProSport Series Heavy Duty Recreational Grade On-Board Marine Battery Charger Owner's Manual and Installation Guide WATERPROOF and SALTWATER TESTED TWO YEAR WARRANTY Constructed to:
More informationDieHard. BATTERY CHARGER/MAINTAINER 1.5 Amp Fully Automatic Float-Mode Monitoring. Model No
OWNER'S MANUAL DieHard. BATTERY CHARGER/MAINTAINER 1.5 Amp Fully Automatic Float-Mode Monitoring Model No. 200.71220 CAUTION: Read and follow all Safety Rules and Operating Instructions Before Every Use
More informationGuardian Battery Charger Series. Installation and Operations Manual Section 75
Guardian Battery Charger Series Installation and Operations Manual 00-02-0615 02-29-08 Section 75 In order to consistently bring you the highest quality, full featured products, we reserve the right to
More informationEASY CHARGE Weather-resistant fixed mount Battery Charger
EASY CHARGE Weather-resistant fixed mount Battery Charger 6 AMP AND 10 AMP MODELS EN NL, DE, FR, ES, IT USER S MANUAL WWW.MASTERVOLT.COM/EASYCHARGE 10000009118/01 2 EN / EasyCharge 6 and 10 Amp - User
More informationELECTRONIC MARINE CONVERTER/CHARGER Owners Manual Models PD2020, PD2030, PD2040, PD2050, PD2060, PD2080
Table Of Contents ELECTRONIC MARINE CONVERTER/CHARGER Owners Manual Models PD2020, PD2030, PD2040, PD2050, PD2060, PD2080 Thank you for purchasing the INTELI-POWER MARINE converter/charger. The INTELI-POWER
More information12V Manual Battery Charger
OPERATOR S MANUAL 12V Manual Battery Charger Model No. 28.71221 Read and follow all Safety Rules and Operating Instructions before Every Use of this Product. SAVE THESE INSTRUCTIONS. Sears Brands Management
More informationLESTRONIC II BATTERY CHARGER MODEL 07210
LESTRONIC II BATTERY CHARGER MODEL 07210 PLEASE SAVE THESE IMPORTANT SAFETY AND OPERATING INSTRUCTIONS For correct operation of the equipment, it is important to read and be familiar with this entire manual
More informationSentry Battery Charger. Installation and Operations Manual Section 75
Sentry Battery Charger Installation and Operations Manual 00-02-0616 03-03-08 Section 75 In order to consistently bring you the highest quality, full featured products, we reserve the right to change our
More informationModel: OBD-L On-Board-Diagnostics II Memory Saver Detector
Model: OBD-L On-Board-Diagnostics II Memory Saver Detector OWNERS MANUAL IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual will show you how to use your memory saver detector safely and
More informationPI1500X Power Inverter User s Manual
PI1500X Power Inverter User s Manual featuring WARNING Failure to follow instructions may cause damage or explosion, always shield eyes. Read entire instruction manual before use. Warning: This product
More information1000 Watt Pure Sine Wave Power Inverter, Users Manual
WF-5100 Series 1000 Watt Pure Sine Wave Power Inverter, Users Manual Distributed in the USA and Canada by Arterra Distribution 2021 Aeroplex Drive North. Elkhart, IN. 46514 Phone: 877-294-8997, Fax: 547-294-8698
More informationBATTERY CHARGER OWNER S MANUAL POWER CHARGER Part # volt Amp
BATTERY CHARGER OWNER S MANUAL POWER CHARGER Part # 74016 12-16 volt Amp ----CAUTION---- READ THIS MANUAL CAREFULLY FOR RULES OF SAFE OPERATION AND PROPER USE OF THIS CHARGER ***SAVE THESE INSTRUCTIONS***
More informationPureSine 150/300 Pure Sine Wave Inverter User s Manual
PureSine 150/300 Pure Sine Wave Inverter User s Manual 1. Important Safety Instructions WARNING! Before you install and use your Inverter, please read and follow these safety instructions. 1-1. General
More informationProSport Series. Owner's Manual and Installation Guide. ProMariner WATERPROOF. Charging. Distributed-On-Demand
ProMariner ProMariner Visit ProMariner Online at www.pmariner.com, for a Complete Selection of Quality Marine Products... Here are just a few: ProSport Series - Recreational Sport Fishing & Boating Waterproof
More informationGSL Electronics Modified Sine Wave Power Inverters
GSL Electronics Modified Sine Wave Power Inverters Congratulations on choosing one of our Modified Sine Wave Inverters for your application. There are 6 models in the range, which will meet most of your
More informationMP V 8A Electronic Smart Charger. Instruction and Information Manual
MP7428 12V 8A Electronic Smart Charger Instruction and Information Manual In order to ensure correct and safe usage of your battery charger, you should read these instructions carefully. Please retain
More informationEASY CHARGE Waterproof portable Battery Charger
EASY CHARGE Waterproof portable Battery Charger 1.1 AND 4.3 AMP MODELS EN NL, DE, FR, ES, IT USER S MANUAL WWW.MASTERVOLT.COM/EASYCHARGE-PORTABLE 10000009117/04 2 EN / EasyCharge 1.1 and 4.3 Amp - User
More information12V Manual Battery Charger & Engine Starter
OPERATOR S MANUAL 12V Manual Battery Charger & Engine Starter Model No. 28.71230 Read and follow all Safety Rules and Operating Instructions before Every Use of this Product. Save these instructions. Sears
More informationBattery. Charger Model: Save Important Safety Instructions
Owner's Manual Battery Charger Model: SS-51A-PE, 10 Amp Fully Automatic Battery Charger For 12 Volt Marine Deep Cycle & Automotive Batteries Save Important Safety Instructions Read Rules for Safe Operation
More informationLESTRONIC II BATTERY CHARGER MODEL 19740
*01679* LESTRONIC II BATTERY CHARGER MODEL 19740 PLEASE SAVE THESE IMPORTANT SAFETY AND OPERATING INSTRUCTIONS For correct operation of the equipment, it is important to read and be familiar with this
More informationSBC / 2140 / Stage Battery Charger User Manual
SBC - 2130 / 2140 / 2150 3 Stage Battery Charger User Manual Keep this manual in a safe place for quick reference at all times. This manual contains important safety and operation instructions for correct
More informationMASTERsine Inverter PXA Series Installation Guide
Backup Power System Expert TM MASTERsine Inverter PXA Series Installation Guide Important Safety Instructions IMPORTANT: Read and save this Installation Guide for future reference. This chapter contains
More informationOwner's Manual and Installation Guide
ProMariner ProMariner ProSport Series Heavy Duty Recreational Grade On-Board Marine Battery Charger Owner's Manual and Installation Guide SMT-DIGITAL WATERPROOF and SALTWATER TESTED Professional Mariner,
More informationOwner s Manual & Safety Instructions
Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s
More informationSafety, Installation and Operating Instructions Instructions importantes concernant la sécurité
! Safety, Installation and Operating Instructions Instructions importantes concernant la sécurité Manual for the following Battery Fuel Gauge models: BFGOV12V, BFGOV24V, BFGOV36V, BFGOV48V, BFGOV64V and
More informationLESTRONIC II BATTERY CHARGER BUILT-IN OR PORTABLE CHARGERS
LESTRONIC II BATTERY CHARGER BUILT-IN OR PORTABLE CHARGERS PLEASE SAVE THESE IMPORTANT SAFETY AND OPERATING INSTRUCTIONS For correct operation of the equipment, it is important to read and be familiar
More informationAUTOMATIC BATTERY CHARGER AUTOMATISCHES BATTERIELADEGERÄT CHARGEUR DE BATTERIE AUTOMATIQUE AUTOMATISCHE ACCULADER 12A RMS (8A DC) MCH12A
AUTOMATIC BATTERY CHARGER AUTOMATISCHES BATTERIELADEGERÄT CHARGEUR DE BATTERIE AUTOMATIQUE AUTOMATISCHE ACCULADER 12A RMS (8A DC) MCH12A Suitable for all type of 12V lead acid, sealed, leisure and gel
More informationVAc A. Rc Ah. Table of contents. OpERATION MAINTENANcE. Safety... 2 Specifications... 6 Operation Maintenance Warranty...
Table of contents Safety... 2 Specifications... 6 Operation... 7 Maintenance... 10 Warranty... 12 SAFETy SpEcIFIcATIONS OpERATION MAINTENANcE VAc A cca Rc Ah WARNING SyMBOLS AND DEFINITIONS This is the
More informationACCUSENSE CHARGE SERIES ON/OFF BOARD FULLY AUTOMATIC BATTERY CHARGER
ACCUSENSE CHARGE SERIES ON/OFF BOARD FULLY AUTOMATIC BATTERY CHARGER SPECIFICATIONS: *Photo for reference only* Part number 8890439 Mode Select: Selects Battery Type Refer to Section 6. IMPORTANT: READ
More informationBS20 BATTERY CHARGER For lead-acid batteries
BS20 BATTERY CHARGER For lead-acid batteries User Manual and Guide to professional battery charging for Starter and Deep Cycle batteries. THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS
More informationSC-7500A, SC-8020A, SC-10030A Automatic Battery Charger
OWNERS MANUAL Models: SC-7500A, SC-8020A, SC-10030A Automatic Battery Charger SC-7500A SC-8020A SC-10030A PLEASE SAVE THIS OWNERS MANUAL AND READ BEFORE EACH USE. This manual will explain how to use the
More informationSCC-MPPT Solar Charge Controller
Solar Charge Controller Quick Guide 200W 300W 400W 600W 850W V. 2.2 1. Introduction solar charge controller uses PWM-based DSP controller to keep the batteries regulated and prevent batteries from overcharging
More informationPOWER TO GET THE JOB DONE
52722 10 AMP 12 VOLT BATTERY CHARGER OWNER S MANUAL OVERCHARGING PROTECTION 10 Amp, 12 Volt Fully automatic and manually selectable Includes overcharging protection in automatic mode Reverse hook-up protection
More informationMODEL A96 SERIES. 130Vdc Switchmode Utility Rectifier / Battery Charger. Used with LaMarche Power Cage ECN/DATE
MODEL A96 SERIES 130Vdc Switchmode Utility Rectifier / Battery Charger Used with LaMarche Power Cage CPN112138 ECN/DATE ISSUE DATE: ECN 17010-12/05 106 BRADROCK DRIVE DES PLAINES, IL. 60018-1967 (847)
More information