G+ LOCKSET. User Guide

Transcription

1 G+ LOCKSET User Guide

2

3 WELCOME TO THE EASIER WAY TO ACCESS YOUR HOME

4 This guide will show you how to install your G+ Lockset. What s IN your G+ LOCKSET BOX? ELECTRIC G+ LOCKSET G+ Lockset: ELECTric including mounting hardware 4 x AAA NiMH BATTERIES 2 x PREMIUM G+ KEYS 2 x CR2032 BATTERIES BATTERY G+ LOCKSET G+ Lockset: BATTERY including mounting hardware 4 x aaa Alkaline batteries 2 x BASIC G+ KEYS 2 X CR2025 BATTERIES Take care! Electricity kills. Switches, power outlets and other fixed wire products must be installed by a licensed electrical contractor or similarly qualified person. DOUBLE CYLINDER DOOR LOCKS (Identified by a key lockable cylinder on both sides of the door). For all Gainsborough double cylinder door locks, we recommend: Do not lock keylock from the inside of the door when occupants are in the building. If you choose to keylock from the inside of the door when occupants are inside the building ensure that the key is readily accessible and operable by all persons who may need to exit the building. Ensure all occupants know how to operate the lock and keys to gain immediate exit.

5 CONTENTS SECTION 1 Overview...2 Mechanical G+ Lockset 2 Battery G+ Lockset 3 Electric G+ Lockset 3 Communication Overview...4 G+ Lockset functions 5 Operation...6 Independent operation of 2 x G+ Locksets 7 Revert to previous mode if the door is not opened 7 Revert to Privacy 7 Error 8 Operating the G+ Lockset with the door open or power off 8 Feedback Electric G+ Lockset only 8 Batteries 10 Layout...12 Typical installation of an Electric G+ Lockset with the In-line Power Unit in the ceiling 12 Close up of Electric G+ Lockset Inside 13 Close up of Electric G+ Lockset Outside 13 Battery box Power Receiver location 14 Teach Mode access 14 Battery access/orientation 15 Shift and Revert to Privacy switches 15 SECTION 2 G+ Lockset Setup...18 Installation 18 Setting Shift and Revert to Privacy switches 18 Programming 19 G+ Key Setup...22 Setting and using the unlock button 23 Installing the batteries 24 SECTION 3 General Specifications...28

6

7 1 OVERVIEW, COMMUNICATION OVERVIEW, OPERATION, LAYOUT

8 Overview The G+ Lockset is an External Door Lockset with 3 primary modes: Deadlock mode the door is locked in both directions. Privacy mode the door is locked from the outside, but occupants are free to exit the building. Passage mode the door allows free passage from inside and outside. NOTE: All G+ Locksets have traditional key operation. The Remote Controls and the traditional mechanical keys control all modes of the Lockset. This user guide covers the set-up and operation of the Electric G+ Locksets and Battery G+ Locksets. The G+ Lockset is available in three versions: Mechanical G+ Lockset The Mechanical G+ Lockset does not require any batteries. The Mechanical G+ Lockset cannot receive commands from Remote Controls. 2 Section 1 Overview

9 Battery G+ Lockset The Battery G+ Lockset is powered by 4 x AAA Batteries. The Battery G+ Lockset can receive commands from G+ Keys / G+ Home Hub / G+ Home Port. The Battery G+ Lockset can be identified by the Magnet above the strike plate. Magnet Electric G+ Lockset The Electric G+ Lockset is powered by 4 x AAA (NiMH) rechargeable batteries that are recharged while the door is closed. The Electric G+ Lockset can receive commands from G+ Keys / G+ Home Hub / G+ Home Port. The Electric G+ Lockset can feed its status back to the Premium G+ Key and G+ Home Hub. The Electric G+ Lockset can be identified by the Power Transfer Unit above the Strike Plate Power Transfer Unit Section 1 Overview 3

10 Communication Overview Basic G+ Key Sends commands to Battery G+ Lockset Premium G+ Key Sends commands to Battery G+ Lockset G+ Home Hub Sends commands to Battery G+ Lockset G+ Home Port Sends commands to Battery G+ Lockset Basic G+ Key Sends commands to Battery G+ Lockset Premium G+ Key Sends commands to Battery G+ Lockset Can receive feedback from the Electric G+ Lockset G+ Home Hub Sends commands to Battery G+ Lockset Can receive feedback from the Electric G+ Lockset G+ Home Port Sends commands to Battery G+ Lockset 4 Section 1 Communication Overview

11 G+ LOCKSET FUNCTIONS Deadlock Mode Privacy Mode Passage Mode Revert to previous locked mode Revert to Privacy Mode after the door is closed if selected Mechanical Key Operation G+ Key Operation MECHANICAL BATTERY ELECTRIC Feedback Section 1 Communication Overview 5

12 Operation OPERATION BY A G+ KEY Premium G+ Key Basic G+ Key Deadlock Privacy Passage Deadlock Privacy Passage Shift Shift NOTE: Do not engage deadlock if anyone is inside the building. Press button 1 to engage Deadlock i.e. To lock the door from both sides. Successful operation will be confirmed by 3 short beeps from the G+ Lockset. Press button 2 to engage Privacy i.e. To lock the outside door handle but leave the inside door handle unlocked. Successful operation will be confirmed by 2 short beeps from the G+ Lockset. Press button 3 to engage Passage i.e. To unlock both the inside and outside door handles. Successful operation will be confirmed by 1 short beep from the G+ Lockset. Press the shift button first to access a second G+ Lockset, then the desired one of the first three buttons. When engaging Deadlock from Privacy, or if both Deadlock and Privacy are mechanically selected together, the lock will sound 1 short beep followed by 1 long beep to alert the user that the Lockset is locked from inside as well as the outside. 6 Section 1 Operation

13 Independent Operation of 2 x G+ Locksets Two G+ Locksets can be operated independently by one G+ Key. The first G+ Lockset is operated by the first 3 buttons on the G+ Key. The second G+ Lockset is operated by first pressing the Shift Button and then operating the first 3 buttons. To setup a G+ Lockset as the second Lockset, See Section 2 Layout: Shift and Revert to Privacy Switches (page 15). Revert to Previous mode if the door is not opened If the G+ Lockset is unlocked via a remote control but the door is not opened in the next 35 seconds, the G+ Lockset will revert back to its previous locked mode, (Deadlock or Privacy). This is to guard against accidental activation by a G+ Key. Revert to Previous mode does not work if the door is unlocked mechanically. Revert to Privacy In standard setting, the G+ Lockset will remain in Passage mode after the door is opened and then closed. The G+ Lockset can be set to automatically revert to the Privacy mode whenever the door is closed. This setting can be accessed by the user via a switch in the Battery Box, See Section 2 Layout: Shift and Revert to Privacy Switches (page 15). Section 1 Operation 7

14 Error If the G+ Lockset is unable to engage the mode requested by a remote control, it will sound an error 3 short beeps followed by 3 long beeps. Possible causes of error include: Low batteries The lever partially operated The mechanical key left in the cylinder Attempting to engage Deadlock mode or Privacy mode when: The door is open The power is off (Electric G+ Lockset only). Operating the G+ Lockset with the door open or power off The G+ Lockset will sound an error if it receives a command from the remote control to engage Deadlock or Privacy while the door is open or power is off. To engage Deadlock or Privacy via a remote control while the door is open or the power is off, the command must be sent 3 times. Feedback Electric G+ Lockset only The Electric G+ Lockset is capable of sending information about its status to suitable Remote Controls. In this manual this information is referred to as feedback. Examples of feedback include: Deadlock mode Privacy mode Passage mode Door Closed G+ Home Hub only. NOTE: The Door Closed signal will indicate door open if power is disconnected to the Electric G+ Lockset. 8 Section 1 Operation

15 Suitable Remote Controls include: Premium G+ Key The Electric G+ Lockset will send back a confirmation, to the Premium G+ Key, that the requested mode has been activated, or it will send back an error. Deadlock confirmation Privacy confirmation Passage confirmation Shift confirmation The Premium G+ Key will display the confirmation as a green light beside the appropriate button. The Premium G+ Key will display an error with the Electric G+ Lockset as a flashing green light beside the appropriate button. In addition to lock error, the Premium G+ Key will display an error if it does not receive feedback from the lock after approximately 35 seconds. If the Premium G+ Key displays the green light beside the shift button at the same time as another confirmation light, it indicates the feedback is from the Electric G+ Lockset operated via the shift button. G+ Home Hub The Electric G+ Lockset will send back regular feedback to the G+ Home Hub, about which mode(s) the Lockset is in and whether the door is closed and the power is on. Feedback is transmitted to the G+ Home Hub approximately once every 2 seconds. Refer to the G+ Home Hub Guide for more information on feedback. Section 1 Operation 9

16 Batteries Electric G+ Lockset The Electric G+ Lockset requires 4x AAA NiMH Rechargeable Batteries which are charged via a Power Transfer Unit when the door is closed. CAUTION! Electric G+ Lockset Use only AAA NiMH Batteries. Other battery types may leak or explode causing injury and damage. Batteries and Power Transfer housings may become hot to touch while charging. Battery G+ Lockset The Battery G+ Lockset requires 4x AAA Alkaline batteries. Gainsborough recommends changing the batteries at the same time as changing smoke alarm batteries. Gainsborough recommends good quality Alkaline batteries. Low Battery Warning If the batteries are low on power or need to be replaced, the Electric G+ Locksets and Battery G+ Locksets will sound a warning after the normal confirmation sounds. NOTE: While the Electric G+ Lockset is charged by mains power, the batteries can run down if the door is left open for an extended period of time. 10 Section 1 Operation

17 Lock confirmation sounds ACTION SOUND 1 Engage Passage Mode 1 short beep 2 Engage Privacy Mode 2 short beeps 3 Engage Deadbolt Mode 3 short beep 4 Engage Privacy and Deadlock at the same time, or, engage Deadlock from Privacy 2 long beeps 5 Engage Teach Mode 1 long, 2 short beeps 6 G+ Key recognised by lock 1 short beep 7 Disengage Teach Mode 1 long, 1 short, 1 long beep 8 Battery Low warning 1 short, 1 long beep 9 Alarm 3 long, 3 short beeps Section 1 Operation 11

18 Layout Typical installation of an Electric G+ Lockset with the In-Line Power Unit in the ceiling NOTE: For the Battery G+ Lockset, the Power Transfer Unit / In-line Power Unit is replaced by a Magnet Power point: existing or an electrician to install In-line Power Unit Power Transfer Unit G+ Lockset Other possible locations for the In-line Power Unit include: Under the floor Behind a panel in the wall 12 Section 1 Layout

19 close up of electric g+ lockset inside Power Receiver Battery Box Power Transfer Unit Privacy button Latch Key operation close up of electric g+ lockset OUTside Key operation Sliding cover Section 1 Layout 13

20 BATTERY BOX LOCATION Power Receiver Battery Box Latch TEACH MODE ACCESS Programming USB Teach Mode activation via paper clip or similar 14 Section 1 Layout

21 BATTERY ACCESS / ORIENTATION Access batteries using battery support Remove screws to access batteries Remove screws to access batteries SHIFT AND REVERT TO PRIVACY SWITCHES Shift selection Revert to privacy selection Section 1 Layout 15

22

23 G+ LOCKset SETUP, G+ KEY SETUP 2

24 G+ Lockset Setup INSTALLATION Refer to installation instructions Setting Shift and Revert to Privacy Switches NOTE: The shift switch should be set prior to teaching any G+ Keys to the G+ Lockset. Changing the setting of the shift switch will require reteaching of all G+ Keys. Shift selection Revert to privacy selection Shift not selected Shift selected Shift not selected Revert to Privacy not selected Revert to Privacy not selected Revert to Privacy selected 18 Section 2 G+ Lockset Setup

25 PROGRAMMING Teaching G+ Keys to a G+ Lockset There are two programming modes for the G+ Lockset: Teach Mode - All previously taught G+ Keys are replaced by G+ Keys taught during this session Delete Mode - All previously taught G+ keys are wiped from the memory. NOTE: Teaching and Deleting G+ Keys does not affect any G+ Home Hubs or G+ Home Ports in the G+ Lockset s memory. Ensure the Shift Mode selection switch is set prior to teaching any G+ Keys to ensure feedback is received by the G+ Key. If the G+ Lockset shift switch is changed after the G+ Keys have been taught: The G+ Lockset will respond to the new buttons. NOTE: Changing the shift switch after teaching may result in unexpected error signals from the Premium G+ Key. Section 2 G+ Lockset Setup 19

26 Teach Mode Perform the following steps to program G+ Keys to a G+ Lockset. Teach Mode activation via paper clip or similar Step 1: Place the G+ Lockset into programming mode by pressing and holding the teach button with a paper clip or similar, until the G+ Lockset emits a Teach confirmation sound (1 long; 2 short beeps), then release the teach button. This should take approximately 3 seconds. NOTE: You have 10 seconds to perform step 2 before Replace Mode times out and reverts back to the list of previously taught G+ Keys. Step 2: Press buttons 4 & 5 on the 1st G+ Key to be taught simultaneously as shown until the G+ Lockset emits a single beep. Premium G+ Key Basic G+ Key Press these buttons together Press these buttons together 20 Section 2 G+ Lockset Setup

27 Step 3: Repeat step 2 for each G+ Key to be taught. Each additional G+ Key must be added within 10 seconds or the G+ Lockset will time out and replace any previously taught G+ Keys with the G+ Keys taught in this session. Step 4: Once the last G+ Key has been taught, wait for the G+ Lockset to emit the Teach Session finish beeps, (1 long; 1 short; 1 long). NOTE: If no G+ Keys are taught during the teach process, the G+ Lockset will remember all of the previously taught G+ Keys. Once the first G+ Key is taught, the G+ Lockset will delete all of the previously taught G+ Keys and only remember G+ Keys taught in this session. In the case of the Electric G+ Lockset, its feedback will replace the feedback of any previously taught feedback devices assigned to buttons 1-3, or 6-8 on the G+ Key. Delete Mode Step 1: Place the G+ Lockset into Delete Mode by pressing and holding down the teach button. The G+ Lockset Teach Indicator will emit the teach confirmation beeps after approximately 2 seconds, and then start to beep again prior to 8 seconds. Step 2: Once the G+ Lockset has stopped beeping after approximately 8 seconds, the programming button can be released. All G+ Keys will have been wiped from the G+ Lockset memory. Teaching a G+ Home Hub to a G+ Lockset (USB connection) Contact a Gainsborough Hardware Industries Licensed Locksmith / Installer to program a G+ Home Hub to a G+ Lockset. Teaching a G+ Home Port to a G+ Lockset Refer to the G+ Home Port manual. Section 2 G+ Lockset Setup 21

28 G+ Key Setup Activation Buttons Unlock Button Key Ring securing point Shift Button Battery Cover Lock switch Enable (shown disabled) Battery Cover removed Activation Buttons Unlock Button Key Ring securing point Shift Button Battery Cover Lock switch Enable (shown disabled) Battery Cover removed 22 Section 2 G+ Key Setup

29 Setting and Using the Unlock Button The unlock button prevents the front buttons from accidentally being pressed by requiring the Unlock button to be pressed prior to operating any of the front buttons. Pressing the Unlock buttons unlocks the front buttons for 5 seconds. Pressing any of the front buttons extends the unlocked time for another 5 seconds. The Unlock button can be enabled / disabled via the switch located inside the battery compartment Disabling the Unlock button results in the activation buttons always being enabled. Unlock button disabled Unlock button enabled Unlock Button Unlock Setting Switch Unlock button disabled Unlock button enabled Unlock Button Unlock Setting Switch Section 2 G+ Key Setup 23

30 Installing the Batteries Step 1: Rotate and remove battery cover Step 2: Insert batteries + side up Step 3: Replace cover and rotate to lock 24 Section 2 G+ Key Setup

31 Step 1: Rotate and remove battery cover Step 2: Insert batteries + side up Step 3: Replace cover and rotate to lock Section 2 G+ Key Setup 25

32

33 3 GENERAL SPECIFICATIONS

34 General Specifications Electrical Specification Power In - Electric G+ Lockset RF Transmission frequencies 240V 50/60Hz AC via plug pack supplied MHz & 918 MHz Memory Capacity Number of G+ Keys 1000 Number of G+ Home Hubs 1 Number of G+ Home Ports 1 Batteries Electric G+ Lockset Battery G+ Lockset Premium G+Key Basic G+ Key 4 x AAA NiMH Life: approximately 5 years 4 x AAA alkaline Life: approximately 1 year 2x CR2032 2x CR2025 Environmental Specification Operating temperature range -10 C to 50 C Storage temperature range -10 C to 60 C Frequently asked questions Refer to the Gainsborough website for frequently asked questions. Contact Customer service Section 3 General Specifications

35 This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance. This document contains general installation information only and is in no way to be regarded as a complete and comprehensive guide. Gainsborough Hardware Industries Limited ACN (Gainsborough Hardware) makes no representation about the content and suitability of this information for any purpose. You should exercise your own independent skill and judgement before you rely on this document and obtain appropriate advice relevant to your particular circumstances. The information is provided as is and without express or implied warranty. Gainsborough Hardware disclaims all warranties, including all implied warranties as to merchantability or fitness. In no event shall Gainsborough Hardware be liable for any direct, special, indirect or consequential damages or any damages whatsoever resulting from loss of income or profits, whether in an action of contract, negligence or other tortuous action, arising in connection with the use or performance of the information in this document. The availability of products set out in this document is not guaranteed and Gainsborough Hardware reserves the right to alter, amend or delete any part of this document without prior notice. This disclaimer is subject to any contrary legislative provisions. Take care! Electricity kills. Switches, power outlets and other fixed wire products must be installed by a licensed electrical contractor or similarly qualified person.

36 Gainsborough Hardware Industries Limited Hotline Head Office Alfred Street Blackburn, VIC 3130 PO Box 330, Blackburn VIC Telephone Admin & Export Fax +61 (0) NSW Suite 1B, 126 Taren Point Rd Taren Point NSW 2229 T F QLD 433 Logan Rd Stones Corner Qld 4120 T F WA 12 Juna Drv Malaga WA 6945 T F VIC Alfred St Blackburn VIC 3130 T F SA 31 Lansdowne Tce Vale Park SA 5081 T F TAS PO Box 330 Blackburn VIC 3130 T F NTH QLD Unit 1/ 17 Camuglia St Mt Louisa QLD 4814 T F NZ Unit 5E 269A Mt Smart Rd Penrose Auckland T F EAS1DOC04CL1 DWGAI0023 PV1.3.12