EM-MPO/400. Multi-parameter Electricity Meter. Installation Instructions. Important: Retain these instructions. Mounting Requirements H O 2

Transcription

1 I V E I V E I V E Multi-para Electricity Meter Important: Retain these instructions Contents 1 Unpacking Storing Installation Disposal Unpacking I V E G Storing -25 C -23 F +7 C +158 F H O 2 <75 %RH 3 Installation 1 Mounting Requirements It is recommended that the installation should comply with the HSE Memorandum of Guidance on Electricity at Work Regulations mm (3.78 ) 83.5 mm (3.29 ) -1 C +14 F +65 C +149 F I V E 96 mm (3.78 ) H O 2 <75 %RH rotection I54 I V E G2118 Issue 3, 6-May-214 1

2 O OK RX V Mounting Requirements (continued) Use with either the EMIC or IQ3/XNC/SER (with MODUS driver) 2.5 m (9 1 ) cable supplied with EMIC EMIC IQ3/XNC/SER (MODUS DRIVER) I V E RS485 2 anel thickness 1 mm (.4 ) to 4 mm (.16 ) repare anel 92 mm (3.62 ) 3 Mount Meter 92 mm (3.62 ) 92 mm +.8 mm -. mm Square ( Square) I V E Slide on 4 clips (supplied) push against panel 4 Connect ower Input to Meter 23 Vac 5/6 Hz ±15 5 W maximum L N 1 2 O I O L ~ N 23 Vac DO NO SWICH ON Single part screw terminals, maximum cross section area cable 4 mm 2 (12 WG) Note that this instrument does not require an earth (ground) connection 2 G2118 Issue 3, 6-May-214

3 5 Connect Measurement Connections O Single part screw terminals, maximum cross section area cable 4 mm 2 (12 WG) 3 phase 3 or 4 wire - Star or Delta (can use Vs) nominal current: 5, nominal voltage: 23 Vac (phase to neutral), 4 Vac (phase to phase) rogrammable: Cs primary: 5 to 25 k, CSENSORS: primary 5 to 8 Vs primary: 11 V to 44 kv () 55 kv (e) Single phase (can use V) Note that uses Cs, e uses current sensors (CSENSOR) - see step 6 3 phase high voltage using 2 Vs and 2 Cs (EM-MO/35 only) 3 phase using 2 Cs - Delta (EM-MO/35 only) G2118 Issue 3, 6-May-214 3

4 6 Ensure Cs and CSENSORs have Correct olarity S1 (+) red S2 (-) lack 1 2 Supply Load Current C S2 (-) white (black/white) S1 (+) black Supply 1 2 Load Supply 1 2 S1 (+) lack Load K L Current K L Current S2 (-) White (lack/white) CSENSOR 1, 1 CSENSOR 15, 4, 8 = rimary S = Secondary Ensure connection to a has correct polarity. C (rend): +(red), - (black); CSENSOR (rend):+(black),-(white or black/white). Ensure current passes through C or CSENSOR in correct direction. Ensure C or sensor is connected to same phase as associated V.. 7 Mount EMIC or IQ3.../XNC/SER EMIC,G2182, Section 3.1 steps 1 to 6 OR IQ3xcite,G2626, IQ3xact,G2766, IQ3/XNC,G2911 IQ3/XNC MODUS Drivers Manual,E G2118 Issue 3, 6-May-214

5 Connect ulse Outputs If required 1 m ac/dc max., 1 V ac/dc max.,.5 W max load ulse 1 ulse 1 kwh Monitor O olarity independant 14 Note: ulse Rate (value of each pulse - kwh, kvrh), ulse Length (duration - s) settable in step ulse 2 ulse 2 kvrh Monitor 9 Connect to EMIC If using EMIC Single part screw terminals, maximum cross section area cable 4 mm 2 (12 WG) 2.5 m (9 1 ) cable supplied with EMIC EMIC O O EMIC RJ45 ort 1 V terminator lack Orange Red lack Data + Data - Red observe correct polarity Orange terminator For runs >3 m use 15 ohm terminators each end. Maximum length is 1 96 aud, with 26 WG cable Maximum number of s (8, 16, 32 dependent on EMIC version). G2118 Issue 3, 6-May-214 5

6 OK RX V Connect to IQ3../XNC/SER (for MODUS Driver) If using MODUS driver IQ3/XNC/SER (MODUS DRIVER) O RS485 IQ3/XNC/SER R R V integral terminator observe correct polarity terminator For runs >3 m use 12 ohm terminators each end. Maximum length is 1 96 aud, with 26 WG cable 11 Switch On O I 6 G2118 Issue 3, 6-May-214

7 12 Configure Meter I V E 5 s Operating Manual, E21116 ages aras Default Note COdE Security code (not Set Up) Ct ri C (CSENSOR) primary 2 1,3 t ri V L-L Voltage ransformer rimary 4 V 2,3 MD ER Min ower Mean Demand Integration eriod -vg ER SEC Current/Voltage ime veraging eriod SEt HRS Run kw Hours Run Set oint 1 4 ULS RtE kwh ulse Rate.1 kwh 5 ULS LEn ulse Length.1 s 5 ULS test HLd ulse Output est r aud Rate 96 6 ddr Unique Modbus ddress 25 ress E, to increase, decrease value respectively Notes: 1., C set values 5 to 25 k. EM-MO/35e,CSENSOR values 5, 5, 1, 15, 4, 8 2. If no V, set to 4 (set scale to 1). If V fitted and primary volts <6 kv, set Nominal Volts to V primary (set scale to 1). If V fitted and primary volts >6 kv, set Nominal Volts to 66 (set Scale to primary volts/66) Note that Scale is set over MODUS. [Readable voltage range: (11 V to 44 kv) e (11 V to 55 kv)] 3. Fine adjust Nominal volts and C primary ( only) allows settings other than those in default tables. I enters and exits Fine djust (icon=f). 4. he hours run set point is the kw level above which the hours run counter will increment. 5 he ulse Rate sets the value of each pulse in kwh - pulse 1, kvrh - pulse 2 (range 1 to 1 counts of register). he ulse Length is the pulse duration in secs (range.1 to 2 s) 6. Set baud rate to match controller (and other s), can be set to 4k8, 9k6, 19k2 baud. Note that protocol fixed at MODUS RU (IEEE) with 16 bit CRC, 8 bit + start bit+ stop bit, no parity G2118 Issue 3, 6-May-214 7

8 OK RX V X RX RS/XEN CS/RXEN Configure MODUS Driver If using MODUS driver he MODUS driver needs to be configured to read the. his requires understanding the communication codes for the paras to be read. IQ3/XNC MODUS Driver Manual, E2111. MODUS Communications Manual, E N L3 L2 L1 Check System Load EMIC V kw ux Input Volts C1 C2 C3 LS L N Ln L1 L2 L O Either Or IQ3/XNC/SER (MODUS DRIVER) V kw 4 Disposal WEEE Directive: t the end of their useful life the packaging and product should be disposed of by a suitable recycling centre. Do not dispose of with normal household waste. Do not burn. lease send any comments about this or any other rend technical publication to techpubs@trendcontrols.com 214 Honeywell echnologies Sàrl, ECC Division. ll rights reserved. Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell echnologies Sàrl, Ecublens, Z.. La ièce, 16, 118 Rolle, Switzerland by its uthorized Representative. rend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof without obligation to notify any person of such revisions or changes. rend Control Systems Limited lbery House, Springfield Road, Horsham, West Sussex, RH12 2Q, UK. el:+44 () Fax:+44 () rend Control Systems US th venue NE, Redmond, Washington 9852, US. el:(425) Fax:(425) G2118 Issue 3, 6-May-214