Helena Snyman - Technical Manager and Sydney Bhengu - Customer Support Technologist Elster Kent Metering (Pty) Ltd. South Africa
|
|
- Margaret Fitzgerald
- 6 years ago
- Views:
Transcription
1 Helena Snyman - Technical Manager and Sydney Bhengu - Customer Support Technologist Elster Kent Metering (Pty) Ltd. South Africa
2 Electricity meter installation and installation verification Safety NRS 057:2005 (Overview) Connections Common Mistakes Tools to verify meter installations Quadrants Vector Diagrams
3 Safety Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices according to national regulatory practices of OCCUPATIONAL HEALTH AND SAFETY ACT, 1993 (ACT NO. 85 OF 1993) and NRS 057-4:2001. Only qualified electrical workers should install this equipment. NEVER work alone.
4 Safety NEVER work on a live panel. Turn off all power supplying the power meter. Always use a properly rated voltage sensing device to confirm that all power is off. Before closing all covers and doors, carefully inspect the work area for tools and objects that may have been left inside the equipment.
5 Safety Use caution while removing or installing panels so that they do not extend into the energized bus; avoid handling the panels, which could cause personal injury. The successful operation of this equipment depends upon proper handling, installation, and operation.
6 Safety NEVER bypass external fusing. NEVER short the secondary of a PT. NEVER open circuit a CT; use a shorting block to short circuit the leads of the CT before removing the connection from the power meter. The power meter should be installed in a suitable electrical enclosure. Failure to follow this instruction will result in death or serious injury
7 NRS 057:2005 Code of practice for electricity metering 4 Requirements of metering installations 4.1 Equipment standards 4.2 Metering system 4.3 General requirements 4.4 Requirements of metering equipment 4.5 Metering installation design 4.6 Metering equipment installation
8 NRS 057:2005 Code of practice for electricity metering 4.7 Compliance of the entire metering installation 4.8 Automated meter reading (AMR) for large power users 4.9 Sealing of metering equipment 4.10 Time offset
9 NRS 057:2005 Code of practice for electricity metering 4.1 Equipment standards Equipment shall comply with the standards applicable when originally installed or with an alternative standard, confirmed in writing by an accredited test laboratory as being equivalent to, or better than, the specified standard.
10 NRS 057:2005 Code of practice for electricity metering 4.2 Metering system The metering system consists of various components each of the components has an influence on the total integrity of the installation. VT s, CT s Junction boxes, Test blocks, Meter Equipment, Ancillary meter equipment, Data validation etc.
11 NRS 057:2005 Code of practice for electricity metering 4.4 Requirements of metering equipment Equipment used in the metering installation shall be certified as compliant with the relevant standards and approved by the licensee. Accuracy class requirements Consists of a meter(s) and associated instrument transformers are determined by the nominal size of the load, expressed in terms of apparent power.
12 NRS 057:2005 Code of practice for electricity metering 4.4 Requirements of metering equipment Calibration of metering installation components (SANAS) Instrument transformers Test certificates Current transformers Voltage transformers Voltage transformer burdening
13 NRS 057:2005 Code of practice for electricity metering 4.4 Requirements of metering equipment Meter panel ancillary equipment Test blocks Meters General requirements Meter type testing Meter calibration Meter numbering
14 NRS 057:2005 Code of practice for electricity metering 4.5 Metering installation design A design report shall be prepared by the metering designer in the case of a new metering installation and in the case where an existing metering installation is modified.
15 NRS 057:2005 Code of practice for electricity metering 4.6 Metering equipment installation General (Training) Meter panel (enclosure) Instrument transformer earths Wiring loom Measurement of current Measurement of voltage
16 NRS 057:2005 Code of practice for electricity metering 4.7 Compliance of the entire metering installation Commissioning report On site verification Testing and inspection of measurement transformers
17 Connections Single Phase, Two Wire, Whole Current Three Phase, Four Wire, Whole Current Three Phase, Four Wire, CT Connected Three Phase, Three Wire, CT Connected Summation
18 LINE LOAD Connections Single Phase, Two Wire, Whole Current A N
19 LINE LOAD Connections Three Phase, Four Wire, Whole Current A B C N S1 VA S2 S1 VB S2 S1 VC S2 Neutral A C B A B C N
20 TO LOAD Connections Three Phase, Four Wire, CT Connected A B C N S1 VA S2 S1 VB S2 S1 VC S2 Neutral A C B A B C N P1 S1 S2 P2 P1 S1 S2 P2 P1 S1 S2 P2
21 TO LOAD Connections Three Phase, Three Wire, CT Connect A B C N S1 VA S2 S1 VB S2 S1 VC S2 Neutral A C B A B C N
22 Feeder 1 TO LOAD Feeder 2 TO LOAD Connections Summation Meter A B C N S1 VA S2 S1 VB S2 S1 VC S2 Neutral Summation CT s S1 S2 S1 S2 S1 S2 P1 P2 P1 P2 P1 P2 P1 P2 P1 P2 P1 P2 A B C N S1 S2 S1 S2 S1 S2 A B C S1 S2 S1 S2 S1 S2
23 Connection Current Transformer
24 Common Mistakes Line and load swapped on whole current meters. The voltage connections for the respective phases A, B & C (L1, L2, & L3) must match the voltage designated inputs to the meter. The current transformer connections for the respective phases A,B & C must match the associated voltage phases to the meter. The current transformers (CT s) need to be oriented properly. Each current transformer indicate the Primary (P1, P2) and Secondary (S2, S1). Incorrect CT rations.
25 Tools to verify the installation Meter display Display indications Instrumentation Software Instrumentation (Live Link) Verification checks Security data Load profile events and flags
26 Tools to verify the installation Display indicators
27 Tools to verify the installation Display - Instrumentation
28 Tools to verify the installation Display - Quadrants
29 Tools to verify the installation Software
30 Tools to verify the installation Software
31 Vector Diagrams 3 Phase 4 wire Unity Power Factor
32 Vector Diagrams 3 Phase 4 wire Unity Power Factor
33 Vector Diagrams 3 Phase 4 wire 30º Lag
34 Vector Diagrams 3 Phase 4 wire 30º Lag
35 Vector Diagrams 3 Phase 4 wire Red CT reversed
36 Vector Diagrams 3 Phase 4 wire Red CT reversed
37 Vector Diagrams 3 Phase 4 wire All CT s reversed
38 Vector Diagrams 3 Phase 4 wire All CT s reversed
39 Vector Diagrams 3 Phase 4 wire Red an Blue Voltages crossed
40 Vector Diagrams 3 Phase 4 wire Red and Blue Voltages crossed
41 Vector Diagrams 3 Phase 4 wire All voltages crossed
42 Vector Diagrams 3 Phase 4 wire All voltages crossed
43 Vector Diagrams 3 Phase 4 wire All Voltages and CT s crossed
44 Vector Diagrams 3 Phase 4 wire All Voltages and CT s crossed
45 Vector Diagrams 3 Phase 3 wire Unity Power Factor
46 Vector Diagrams 3 Phase 3 wire Unity Power Factor
47 Vector Diagrams 3 Phase 3 wire 30º Lag
48 Vector Diagrams 3 Phase 3 wire 30º Lag
49 Vector Diagrams 3 Phase 3 wire 30º Lag, Red CT reversed
50 Vector Diagrams 3 Phase 3 wire Red and Blue Voltages Crossed
51 Vector Diagrams 3 Phase 3 wire 30º Lag, Red and Blue Voltages Crossed
Technical Specificaions. kwh Energy Meter
Technical Specificaions of kwh Energy Meter (SPK300) Class 1.0S Sai PowerrZerve 29/3B, Rajalakshmi Nagar, 1 st Main Road, Velachery Bye Pass, Chennai 600 042. Website :www.spowerz.com Email : info@spowerz.com
More informationModels beginning with MO, MK, 7B, 6S, 6F or 5B. Product Description. Technical Specifications. Installation Instructions.
Models beginning with MO, MK, 7B, 6S, 6F or 5B The Mini Meter Product Description Technical Specifications Installation Instructions February 28 th, 2013 1. Product Description...2 1.1 General Description...2
More informationPowerLogic High Density Metering System 4-Meter Enclosure Installation Guide
PowerLogic High Density Metering System 4-Meter Enclosure Installation Guide 7002-0289-00 Instruction Bulletin HAZARD CATEGORIES AND SPECIAL SYMBOLS Read these instructions carefully and look at the equipment
More informationWP2 - CFD Private Network Meter Commissioning, Proving and Calibration Tests
WP2 - CFD Private Network Meter Commissioning, Proving and Calibration Tests EMRS Working Practice Public Version: 2.0 Date: 13 October 2017 Table of Contents Change Amendment Record 3 1. Introduction
More informationJabulani Ngobese KA & New Technology Development Manager Elster Kent Metering (Pty) Ltd South Africa
Jabulani Ngobese KA & New Technology Development Manager Elster Kent Metering (Pty) Ltd South Africa The benefits from electronic 160A direct connect complex meters for Utilities Note: Accepts up to 70mm
More informationUniversity of Houston Master Construction Specifications Insert Project Name
SECTION 26 13 13 MEDIUM VOLTAGE SWITCHGEAR PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Divisions 0 and 1 and Section 26 00 01, Electrical General
More informationDER Commissioning Guidelines Community Scale PV Generation Interconnected Using Xcel Energy s Minnesota Section 10 Tariff Version 1.
Community Scale PV Generation Interconnected Using Xcel Energy s Minnesota Section 10 Tariff Version 1.3, 5/16/18 1.0 Scope This document is currently limited in scope to inverter interfaced PV installations
More informationBHARAT HEAVY ELECTRICALS LIMITED, JHANSI
BHARAT HEAVY ELECTRICALS LIMITED, JHANSI DESIGN, MANUFACTURING, TESTING, SUPPLY INSTALLATION AND COMMISSIONING OF 11KV VACUUM CIRCUIT BREAKER NOTE : 1 VENDOR must submit complete information against clause
More informationProduct Overview. Product Identification. Amps One CT Two CTs Three CTs
AH06 (optional mounting bracket for small, medium, and large CTs) DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Follow safe electrical work practices. See NFPA 70E in the USA, or applicable
More information- Wiring Brochure Mixing Expansion Module 440
- Wiring Brochure Mixing Expansion Module 440 W 440 12/08 1 Information Brochure Choose controls to match application Application Brochure Design your mechanical applications 2 3 Rough-in Wiring Rough-in
More information9200 Revenue Meter. Model Certification Current Inputs. Complies with the accuracy requirements of the ANSI C Revenue Metering Standard
9200 Revenue Meter This document applies to 9200 meters with firmware version 205 or greater, and explains how to set up and seal the meter for revenue functionality. Revenue meters provide power measurements
More informationPowerCom Pre-Payment. November Next Generation Smart Grid Solutions. For Further Information Please Contact:
PowerCom Pre-Payment Next Generation Smart Grid Solutions November 2012 For Further Information Please Contact: joseph.wittman@powercom.co.il 1 +972 54 6888 341 Overview Powercom prepayment system is an
More informationBulletin 1497A Machine Tool Transformers
Bulletin A Overview/Catalog Number Explanation Bulletin A Bulletin A are designed to reduce supply voltages to control circuits. The complete line of transformers is available with optional factory-installed
More informationANSI Switchboard Meters
ANSI Switchboard Meters High quality range of switchboard instruments with Class 1 accuracy and which complies with American ANSI-C39.1 (1981) specifications. Available in 4 1 /2" case size, the rugged
More informationAC Wattmeters and VArmeters
AC Wattmeters and VArmeters The Crompton Instruments Switchboard series of AC Wattmeters and VArmeters incorporate a DC moving coil, pivot and jewel indicator with a micro-circuit watt transducer PCB to
More informationPowermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Floating Control
Powermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Floating Control Document No. 155-314P25 EA 599-16 Description Features Application Product Numbers The Powermite 599 MT Series SSC81U and
More informationNATIONAL REGULATOR FOR COMPULSORY SPECIFICATIONS ACT (ACT 5 OF 2008) AS AMENDED THROUGH THE LEGAL METROLOGY ACT (ACT 9 OF 2014)
284 No. 41473 GOVERNMENT GAZETTE, 2 MARCH 2018 N0.173 DEPARTMENT OF TRADE AND INDUSTRY 02 MARCH 2018 NATIONAL REGULATOR FOR COMPULSORY SPECIFICATIONS ACT (ACT 5 OF 2008) AS AMENDED THROUGH THE LEGAL METROLOGY
More informationMODEL 422 Submersible Pump Controller
MODEL 422 Submersible Pump Controller Monitors True Motor Power (volts x current x power factor) Detects Motor Overload or Underload Operates on 120 or 240VAC, Single-phase or 3-phase Built-in Trip and
More informationBulletin 1497A Machine Tool Transformers
Bulletin A Overview/Catalog Number Explanation Bulletin A Bulletin A are designed to reduce supply voltages to control circuits. The complete line of transformers is available with optional factory-installed
More informationSOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-19459-8 SOUTH AFRICAN NATIONAL STANDARD Verification standards for the verification of volume-measuring instruments, including commercial standards of volume Published by Standards South
More informationIntegrated Plant Control and Q on Demand 24/7 SUNNY TRIPOWER
24/7 SUNNY TRIPOWER 1 Function Availability Reactive power is necessary for the stability of the utility grid. With the functions "Integrated Plant Control" and "Q on Demand 24/7", SMA Sunny Tripower inverters
More informationUBC Technical Guidelines Section Edition Commissioning of Electrical Systems Page 1 of 5
Page 1 of 5 1.0 GENERAL 1.1 Coordination Requirements.1 UBC Building Operations Electrical Technical Support.2 UBC Energy & Water Services 2.0 REQUIREMENTS FOR COMMISSIONING AND TESTING 2.1 Testing.1 Unit
More informationEP Ground Filter Products. I n s t a l l a t i o n a n d M a i n t e n a n c e M a n u a l. Power Quality For The Digital Age
Power Quality For The Digital Age EP Ground Filter Products I n s t a l l a t i o n a n d M a i n t e n a n c e M a n u a l www.ep2000.com 800.500.7436 EP Ground Filter Products Installation and Maintenance
More informationSDM320D / SDM320A. Single phase din rail meter SDM320D / SDM320A user manual
SDM320D / SDM320A DIN Rail Single Phase Two Wire Energy Meter with S0 Pulse Output (Four modular) User Manual ------------------- 1.1 Safety instruction 1.2 Introductions 1.3 Performance criteria 1.4 Specifications
More informationAurora Wind Interface Box
Aurora Wind Interface Box Installation and Operator s Manual Page 2 of 15 REVISION TABLE Document Revision Author Date Change Description 1.0 T. Melzl 5/9/2006 First release of the document SAVE THESE
More informationBP OIL -- TOLEDO REFINERY
BP OIL -- TOLEDO REFINERY Document Type: Procedure Effective Date: August 31, 2017 Owner: Dane P. Clark Refinery Wide Electrical Distribution System Switching and Isolation Auth. By: Rick J. Chmelovski
More informationINTERCONNECTION STANDARDS FOR PARALLEL OPERATION OF SMALL-SIZE GENERATING FACILITIES KILOWATTS IN THE STATE OF NEW JERSEY
INTERCONNECTION STANDARDS FOR PARALLEL OPERATION OF SMALL-SIZE GENERATING FACILITIES 10-100 KILOWATTS IN THE STATE OF NEW JERSEY January 1, 2005 Rockland Electric Company 390 West Route 59 Spring Valley,
More informationBAPI-Stat 4 Room Humidity Sensor (BA/ B4 -H200 Series)
Overview The BAPI-Stat 4 Style room unit is available as a humidity only sensor or as a combination temperature and humidity sensor with optional LCD display, temperature setpoint adjustment and occupant
More informationBulletin Interconnection of electric power production sources Rules 2-010, , , , , , and
Bulletin 84-1-11 Interconnection of electric power production sources Rules 2-010, 64-078, 64-110, 84-004, 84-008, 84-018, 84-022 and 84-030 Scope Issued May 2018 Supersedes Bulletin 84-1-10 1) Requirements
More informationPowermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Proportional Control
Powermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Proportional Control Document No. 155-313P25 EA 599-15 Description The Powermite 599 MT SSC61U and SSC61.5U series of electronic valve actuators
More informationPLATINUM SERIES SWITCHBOARD METERS
PLATINUM SERIES SWITCHBOARD METERS www.sifamtinsley.co.uk DATASHEET E471457 Multifunction Meters Transducers & Isolators PLATINUM SERIES SWITCHBOARD METERS Temperature Controllers Converters & Recorders
More informationSwitching DC Power Supply
99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Model 1693, 1694 Switching DC Power Supply INSTRUCTION MANUAL 1 Safety Summary
More informationProduct Manual (Revision C) Original Instructions. Air/Fuel Ratio Control. Installation and Operation Manual
Product Manual 36044 (Revision C) Original Instructions Installation and Operation Manual General Precautions Read this entire manual and all other publications pertaining to the work to be performed before
More informationOwner's/Installation Manual
Owner's/Installation Manual Power Management Module (PMM) and Starter Kit NOTE: The starter kit must be purchased and installed prior to individual PMM usage. Model Numbers: 00686-0 PMM 00699-0 PMM WITH
More informationCHILLED WATER CONNECTION CHECKLIST AND APPROVAL. Item Notes By Date Passivation Complete Flushing Complete Nitrate corrosion Residual value:
CHILLED WATER CONNECTION CHECKLIST AND APPROVAL Passivation Complete Flushing Complete Nitrate corrosion Residual value: inhibitor added Pipe labeling complete and correct Pipe insulation in place Pipe
More informationPowermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Proportional Control
Powermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Proportional Control Technical Instructions Document No. 155-313P25 EA 599-15 EA1157R1 Description The Powermite 599 MT SSC61U and SSC61.5U
More informationSolar module user manual Conergy PM 225P-250P
Solar module user manual Conergy PM 225P-250P 1 Introduction 1.1 Short description Conergy PM modules are solar modules for installation in photovoltaic systems. 1.2 About this manual 1.2.1 Subject of
More informationCutler-Hammer. Installation Instructions for the Digitrip OPTIM Pole Trip Unit Installation and Operation with L-Frame Series C Circuit Breakers
Cutler-Hammer Installation Instructions for the Digitrip OPTIM 550 3-Pole Trip Unit Installation and Operation with L-Frame Series C Circuit Breakers Table of Contents Description Page 1.0 General Information......................1
More informationDocument Requirements for Engineering Review PV Systems v1.0 6/9/2017
Document Requirements for Engineering Review PV Systems v1.0 6/9/2017 Outlined below are the documents and associated minimum details required for Engineering Review of Distributed Energy Resources Interconnection
More informationACC Series Power Conditioner OPERATION & INSTALLATION MANUAL
ACC Series Power Conditioner OPERATION & INSTALLATION MANUAL PHASETEC digital power conditioners are designed to safely operate electrical equipment in the harshest power quality environments. With a wide
More informationSE-125 MANUAL GROUND-FAULT GROUND-CHECK MONITOR
SE-125 MANUAL GROUND-FAULT GROUND-CHECK MONITOR FEBRUARY 14, 2001 REVISION 3 Publication: SE-125-M Document: S95-C125-00000 Printed in Canada. Copyright 2001 by Startco Engineering Ltd. All rights reserved.
More information- Wiring Brochure Zone Manager 335
- Wiring Brochure W 335 12/08 1 Information Brochure Choose controls to match application 2 Application Brochure Design your mechanical applications Rough-in Wiring Rough-in wiring instructions 3 4 Wiring
More informationWEM-MX-333mV. Integrated Meter Installation Guidelines
WEM-MX-333mV Integrated Meter Installation Guidelines Energy Tracking, LLC Dated: February 8, 2013 By: Support Staff Table of Contents Enclosure Mounting... 2 High Voltage Wiring Type... 4 High Voltage
More informationCRITERIA FOR LABORATORY ACCREDITATION IN THE FIELD OF FORCE METROLOGY:- CALIBRATION OF UNIAXIAL TESTING MACHINES
CRITERIA FOR LABORATORY ACCREDITATION IN THE FIELD OF FORCE METROLOGY:- CALIBRATION OF UNIAXIAL TESTING MACHINES Approved By: Chief Executive Officer: Ron Josias Executive - Accreditation: Mpho Phaloane
More informationMJÖLNER 200 Microhmmeter
Fully automatic testing Micro processor controlled Safe test DualGround and Remote control True DC ripple free current Lightweight suitcase withstands the impact of water, dust or sand Built in thermal
More informationDEPARTMENT OF TRADE AND INDUSTRY NO APRIL 2016
Trade and Industry, Department of/ Handel en Nywerheid, Departement van 438 National Regulator for Compulsory Specifications Act (5/2008): Amendments to the Compulsory Specification for Earth Leakage Protection
More information- Wiring Brochure Zone Manager 336
- Wiring Brochure W 336 12/08 1 Information Brochure Choose controls to match application Application Brochure Design your mechanical applications 2 3 Rough-in Wiring Rough-in 4 Wiring Brochure Wiring
More informationPF Guard Power Factor Capacitor Bank Installation, Operation, and Maintenance Manual
PF Guard Power Factor Capacitor Bank Installation, Operation, and Maintenance Manual No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means,
More informationENGINE GOVERNING SYSTEMS LSM672 LOAD SHARING MODULE. GOVERNORS AMERICA CORP. 720 Silver Street Agawam, MA , USA MEMBER
ENGINE GOVERNING SYSTEMS LSM672 LOAD SHARING MODULE MEMBER GOVERNORS AMERICA CORP. 720 Silver Street Agawam, MA 01001-2907, USA LSM672 LOAD SHARING MODULE PRODUCT TECHNICAL INFORMATION PTI 4000 AUGUST
More informationECS CONNECTION OF LARGE LV SERVICES TO SECONDARY DISTRIBUTION SUBSTATIONS
Network(s): Summary: ENGINEERING CONSTRUCTION STANDARD ECS 03-0054 CONNECTION OF LARGE LV SERVICES TO SECONDARY DISTRIBUTION SUBSTATIONS EPN, LPN, SPN This standard details the procedures to be undertaken
More informationCP-250E-60/72-208/240-MC4 Microinverter with Modular Trunk Cable
CP-250E-60/72-208/240-MC4 Microinverter with Modular Trunk Cable Chilicon Power Aug 2016 1 CONTENTS CP-250E Microinverter System... 3 The CP-100 Cortex Gateway... 3 Important Safety Information... 4 Inverter
More informationInitial and Periodic Inspection and Testing of Electrical Installations ( ) Sample Test
Initial and Periodic Inspection and Testing of Electrical Installations (2391-052) Sample Test Version 1.1 January 2018 Please note this is not a complete sample theory exam, this document consists of
More informationUtilization of Electric Power Laboratory 3 rd Year G2: Testing & Characteristic of MCCB Used in Commercial and Industrial Applications
G2: Testing & Characteristic of MCCB Used in Commercial and Industrial Applications Contents 1. Laboratory Objective... 4 2. MECHANICAL OPERATION TESTS... 4 2.1 Purpose... 4 2.2 Procedure... 4 2.3 Results...
More informationDocument Requirements for Engineering Review- PV Systems v1.1 12/6/2018
Document Requirements for Engineering Review- PV Systems v1.1 12/6/2018 Outlined below are the engineering documents and their associated minimum detail requirements for a Distributed Energy Resource (DER)
More informationInformation Bulletin. Fire Pump Battery Failures. Version 1.1 Approved for release August 2011
Version 1.1 Approved for release August 21 1.0 Purpose Statement The purpose of this is to raise awareness amongst stakeholders about concerning industry trends associated with batteries supporting fire
More informationDANGER. Instruction Bulletin WARNING. Shunt Trip Kit for Manual DS/DSL Circuit Breakers POWER ZONE III Low Voltage Switchgear Class 6035 INTRODUCTION
Instruction Bulletin Bulletin No. 44027-017-01 Middletown, OH USA Class 6035 INTRODUCTION This bulletin contains instructions for adding a shunt trip assembly to a manual DS/DSL circuit breaker and modifying
More informationContents. 1 Introduction. 2. Advisory and Information Systems. 3. Supply. 3.1 Quality of Electric Supply. 3.2 Interference with other Customers
DISTRIBUTION CODE Contents 1 Introduction 2. Advisory and Information Systems 3. Supply 3.1 Quality of Electric Supply 3.2 Interference with other Customers 3.3 Application for the Supply of Electricity
More information- Wiring Brochure Universal Reset Module 422
- Wiring Brochure Universal Reset Module 422 W 422 03/09 1 Information Brochure hoose controls to match application Application Brochure Design your mechanical applications 2 3 Rough-in Wiring Rough-in
More informationAFTER GAZETTING (WORKING DOCUMENT FOR A 3 YEAR PERIOD) DATE PAGE PARAGRAPH DESCRIPTION ORIGINATOR APPROVED
PART B-07 TITLE: SERVICE CONNECTIONS SPECIFICTION NO: B-07 INCEPTION DATE: AFTER GAZETTING (WORKING DOCUMENT FOR A 3 YEAR PERIOD) AMENDMENTS / REVISIONS DATE PAGE PARAGRAPH DESCRIPTION ORIGINATOR APPROVED
More informationGuide for Primary Injection Testing WL Circuit Breakers. Document No. : 11-C
s Guide for Primary Injection Testing WL Circuit Breakers Document No. : 11-C-9036-00 Before Beginning... Qualified Person Siemens type WL circuit breakers should only be only be operated, inspected, and
More informationFAQ s. Designing metering switchboards as per Victorian service installation rules
FAQ s Designing metering switchboards as per Victorian service installation rules Designing metering switchboards as per Victorian service installation rules Q: Who develops the Victorian service installation
More informationKEY FEATURES TEST CAPABILITIES STANDARDS COMPLIANCE
KEY FEATURES 590G-V2 CT ERROR TESTER Since 1999, Red Phase has made a revolutionary CT error tester. This new method allowed utilities around the world to test their CT s in an easier and faster way than
More informationModulating control valves with magnetic actuators, PN 16
4 461 Modulating control valves with magnetic actuators, PN 16 for drinking water, cold water and hot water systems, DVGW approved MXG461B.. Short positioning time (< 2 s), high resolution (1 : 1000) Selectable
More informationQuick Start Guide TS 910 & TS 920
Quick Start Guide TS 910 & TS 920 DANGER HAZARD OF ELECTRICAL SHOCK, EXPLOSION, OR ARC FLASH Read and understand this quick start guide before installing and operating the transfer switch The installer
More informationOICA Draft Proposal for the ELSA Meeting July in Bonn
OICA Draft Proposal for the ELSA Meeting July 22-24 in Bonn ELECTRICAL SAFETY PROVISIONS FOR VEHICLES IN USE 1. Scope General This module shall apply to the drive train of electric vehicles, hybrid vehicles
More informationENERGY EFFICIENCY NATIONAL BUILDING REGULATIONS. Development Management Department 1 of 49
ENERGY EFFICIENCY NATIONAL BUILDING REGULATIONS 1 of 49 BACKGROUND 2 of 49 National Energy Efficiency Strategy of the Republic of South Africa March 2005 ( Reviewed 2008 / 2011 ) 3 of 49 OBJECTIVES Develop
More informationElectrical Awareness and Considerations
Electrical Awareness and Considerations By David Taylor FIHE MIET IEng Objectives Awareness of specifications. Awareness of Distribution Network Operators (DNO) earthing arrangements. Awareness of basic
More informationRaritan PX. Power Cord Installation Guide. Safety Guidelines. Safety Instructions
QS Rule Raritan PX Power Cord Installation Guide This installation guide explains how to install power cords on Raritan PX products that do not come with a factory installed power cord. This type of product,
More informationEU-Mexico Free Trade Agreement EU TEXTUAL PROPOSAL
This document contains an EU proposal for a legal text on an annex on motor vehicles and equipment and parts thereof to the Trade in Goods chapter in the Trade Part of a possible modernised EU-Mexico Association
More informationActionpac LNS4. Panel Installation Datasheet. Actionpac LNS4 RELEASE 1.0 JUNE In partnership
Actionpac LNS4 Panel Installation Datasheet ELECTROSTATIC SENSITIVE DEVICE This product forms part of a life safety system. Failure to correctly store, handle, install and maintain the product will directly
More informationELECTRICAL INSPECTOR EXAMINATION 14 November 2015 QUESTION AND ANSWER BOOKLET Time Allowed: Three hours
Candidate Code No. IT 32 For Board Use Only Result Date Int Result Date Int ELECTRICAL INSPECTOR EXAMINATION 14 November 2015 QUESTION AND ANSWER BOOKLET Time Allowed: Three hours INSTRUCTIONS READ CAREFULLY
More informationPower Line Communications Metering Systems. RSM-5c RSM-5. Installation Manual
Power Line Communications Metering Systems RSM-5c RSM-5 Installation Manual Table of Contents Chapter 1 Introduction 1 Chapter 2 Installation 2 Chapter 3 Fuse Block Connections 6 Chapter 4 Menu Navigation
More informationCustomer Requirements Downtown Secondary Network Service
Application This standard describes the limitations and requirements for receiving service from the Tacoma Power secondary network system within the City of Tacoma downtown core area. In This Standard
More informationIOM A-0984E IP68-420DC AUTOMATED PILOT ACTUATOR Installation and Operation Manual
IOM A-0984E IP68-420DC AUTOMATED PILOT ACTUATOR Installation and Operation Manual Please ensure to read and understand the contents of this manual. TABLE OF CONTENTS 1 HEALTH AND SAFETY: READ FIRST...3
More informationProduct Overview. Enclosure for batteries N PE/G. Battery (customer-provided - shown for reference only) Battery output terminals
Product Overview Enclosure for Transformer Installation MGE TM Galaxy TM 3500 and Smart-UPS VT Enclosure for Batteries and Enclosure for Transformer 400 V Enclosure for batteries PE/G ; PE/G Unistruts
More informationControl Circuit Transformers
Technical Data Control Circuit Transformers Bulletin Numbers 1497, 1497A, 1497B, 1497D Topic Page Summary of Changes 1 Control Circuit Transformers Product Overview 2 Bulletin 1497 Global Control Circuit
More informationDIGITAL RCD(ELCB) TESTER
INSTRUCTION MANUAL DIGITAL RCD(ELCB) TESTER KEW 5410 R KYORITSU ELECTRICAL INSTRUMENTS WORKS, LTD. Contents 1. Safety Warnings.... 1 2. Procedure of removing Cover. 3 2-1 Method of removing the Cover.
More informationCompliance of Solar PV Installation with the New Renewables SA Grid Code Jimmy Goulding, Electrical Technologist, Aurecon, South Africa
Compliance of Solar PV Installation with the New Renewables SA Grid Code Jimmy Goulding, Electrical Technologist, Aurecon, South Africa Content Introduction Overview of Categories for Grid Connection of
More informationDistribution transformers Efficiency over life-cycle
Distribution transformers Efficiency over life-cycle ABB a global leader ABB is a global leader in Power and Automation technologies that enable utility and industry customers to improve performance while
More informationISO Rules Part 500 Facilities Division 502 Technical Requirements Section Interconnected Electric System Protection Requirements
Applicability 1 Section 502.3 applies to: the legal owner of a generating unit directly connected to the transmission system with a maximum authorized real power rating greater than 18 MW; the legal owner
More informationInstallation and Maintenance Instructions. World Leader in Modular Torque Limiters. PTM-4 Load Monitor
World Leader in Modular Torque Limiters Installation and Maintenance Instructions PTM-4 Load Monitor 1304 Twin Oaks Street Wichita Falls, Texas 76302 (940) 723-7800 Fax: (940) 723-7888 E-mail: sales@brunelcorp.com
More informationH81xx. H81xx Energy Meter. quick install POWER MONITORING INSTALLATION GUIDE. Installer s Specifications
POWR MOITORIG ISTLLTIO GUI H81xx H81xx nergy Meter H06 (optional mounting bracket) Installer s Specifications Insulation lass 600V Sample Rate 1280 Hz Internal Isolation 2500V Operating Temp. Range 0 to
More informationTHREE-PHASE FOUR-WIRE, CT TYPE, 1.5(6A) User Manual for SGE-353
Electronic kwh Counter THREE-PHASE FOUR-WIRE, CT TYPE, 1.5(6A) User Manual for SGE-353 1. Introduction It is a simple three phase four module Din-Rail meter, which is widely used in Sub-metering system.
More informationSafe, reliable, long lasting Lithium Iron Phosphate battery. Next generation capture and release technology. Increased efficiency for greater savings
PowerFlow AC Battery Storage System A fully integrated AC coupled battery Storage System. Dial up the sun whenever you need it Installers System Owners Utilities Designed for Retrofit Existing PV system
More informationFan Coil Unit (FCU) Fan Motor Control
Fan Coil Unit (FCU) Fan Motor Control Fan Relay Board 2 (FRBii) Installation, Operation, and Maintenance The Fan Relay Board assembly (FRBii) provides electronic control for the fan motor and various connections
More informationElectric Vehicle Charging Safety Guidelines Part 2: Selection and Installation Edition DRAFT
Date of publication: 1 November 2016Not yet published Issued by: Mark Wogan, Manager Energy Safety WorkSafe New ZealandNot yet issued Electric Vehicle Charging Safety Guidelines Part 2: Selection and Installation
More informationOperator s Manual. Fairbanks FH Series by Fairbanks Scales, Inc. All rights reserved. . Revision 1 06/2017
Operator s Manual Fairbanks FH Series 2017 by Fairbanks Scales, Inc. All rights reserved 51393. Revision 1 06/2017 Amendment Record Fairbanks FH Series Operator s Manual Operator s Manual Document 51393
More information1000 Series Piston Type Differential Pressure Gauges
1000 Series Piston Type Differential Pressure Gauges 1. Safety Before installing, check the Series Number and verify compatibility to the process media and temperature in contact with the wetted parts.
More informationMonicon Instruments Co., Ltd. CHR-1285/2485 CHR-1285/2485 BATTERY CHARGER
CHR-1285/2485 BATTERY CHARGER TEL:886-4-2238-0698 FAX:886-4-2238-0891 Web Site:http://www.monicon.com.tw E-mail:sales@monicon.com.tw Copyright 2007 Monicon Instruments Co., Ltd. All right reserved. Contents
More informationSymmetra PX with Maintenance Bypass
Symmetra PX with Maintenance Bypass 250/500 kw 400/480 V Installation 12/2016 www.schneider-electric.com Legal Information The Schneider Electric brand and any registered trademarks of Schneider Electric
More informationLouisville Gas and Electric Company
P.S.C. Electric No. 11, Original Sheet No. 57 APPLICABLE In all territory served. AVAILABILITY OF SERVICE Available to any customer-generator who owns and operates a generating facility located on Customer
More informationGETTING STARTED GUIDE NI AI, ±10 V, 12 Bit, 500 ks/s Aggregate
GETTING STARTED GUIDE NI 9201 8 AI, ±10 V, 12 Bit, 500 ks/s Aggregate This document explains how to connect to the NI 9201. In this document, the NI 9201 with screw terminal, NI 9201 with spring terminal,
More informationFEBRUARY 14, 2017 Elastimold Solid dielectric switchgear customer presentation
FEBRUARY 14, 2017 Elastimold Solid dielectric switchgear customer presentation Elastimold solid dielectric switchgear agenda Compelling value Design principles Product overview Switchgear applications
More informationAPEX DRIVE USER GUIDE ADDENDUM: LVD INSTALLATION INSTRUCTIONS
APEX DRIVE USER GUIDE ADDENDUM: LVD INSTALLATION INSTRUCTIONS Product Type: APEX10, APEX20 and APEX40 Servo Drives The above products are in compliance with the requirements of directives 72/23/EEC Low
More informationMAKING MODERN LIVING POSSIBLE. UniLynx Indoor Installation Manual. ULX 1800i ULX 3000i ULX 3600i ULX 5400i SOLAR INVERTERS
MAKING MODERN LIVING POSSIBLE UniLynx Indoor Installation Manual ULX 1800i ULX 3000i ULX 3600i ULX 5400i SOLAR INVERTERS Contents Contents 1. Introduction 2 Introduction 2 Installation Sequence 2 Important
More informationDifferential Pressure Sensors
1 910 1910P01 Differential Pressure Sensors for air or nonaggressive gases QBM66... Pressure-linear characteristic with selectable pressure measuring range Operating voltage AC 24 V or DC 13.5...33 V Output
More informationTFA Flowmeter for Saturated Steam Service Installation and Maintenance Instructions
1930051/2 IM-P193-03 MI Issue 2 TFA meter for Saturated Steam Service Installation and Maintenance Instructions This guide must be read in conjunction with the Installation and Maintenance Instructions
More informationQuick Start Guide TS 910
Quick Start Guide TS 910 DANGER HAZARD OF ELECTRICAL SHOCK, EXPLOSION, OR ARC FLASH Read and understand this quick start guide before installing and operating the transfer switch The installer is responsible
More informationILED Dorado. User Manual
10NM U-code Medium Intensity Obstruction Light Helideck Status Light 15NM U-code Contents 1. Safety... 3 2. Warranty... 3 2.1 General... 3 2.2 Life span... 3 3. Type plate... 4 4. Product Description...
More informationIntegrated temperature test and calibration bench Model CBS-SC4000
Calibration technology Integrated temperature test and calibration bench Model CBS-SC4000 WIKA data sheet CT 92.33 Applications Testing and calibration of temperature measuring instruments such as: - Mercury
More information