Your Premier Pump Choice!

Transcription

1 Limited Warranty During the time periods and subject to the conditions hereinafter set forth, Keen Pump will repair or replace to the original user or consumer, any portion of your new Keen product which proves defective due to defective materials or workmanship of Keen Pump. Contact your closest authorized Keen Pump representative or distributor for warranty service. At all times, Keen Pump shall have and possess the sole right and option to determine whether to repair or replace defective equipment, parts or components. Damage caused by acts of GOD or conditions beyond the control of Keen Pump is not covered by this warranty. Your Premier Pump Choice! WARRANTY PERIOD: 12 Months from date of manufacture. Start-up reports may be required to support warranty claims. Warranty effective only if Keen Pump supplied or authorized control panels are used. Single phase pumps must utilize Keen Pump supplied start components. THIS WARRANTY WILL NOT APPLY: (1) To defects or malfunctions resulting from failure to properly install, operate or maintain the product in accordance with printed instructions provided. (2) To failures resulting from abuse, accident or negligence. (3) To normal maintenance services and the parts used in conjunction with such service. (4) To products which are not installed in accordance with applicable local codes, ordinances and good trade practices. (5) The product is used for purposes other than for what is was designed and manufactured. (6) If 3-phase motors are installed on a single phase power supply using a phase converter or if 3-phase power is supplied by only two transformers, making an open Delta system. WARRANTY EXCLUSIONS: Keen Pump specifically disclaims the implied warranties of merchantability and fitness for a particular purpose after the termination of the warranty period set forth herein. No warranties or representations at any time made by any representatives of Keen Pump shall vary or expand the provision hereof. LIABILITY LIMITATION: In no event shall Keen Pump be liable or responsible for consequential, incidental or special damages resulting from or related in any manner to any Keen Pump product or parts thereof. Personal injury and/or property damage may result from improper installation. Keen Pump disclaims all liability, including liability under this warranty, for improper installation. Keen Pump recommends following the instructions in the installation manual. When in doubt, consult a professional. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. LABOR, ETC., COSTS: Keen Pump shall in no event be responsible or liable for the cost of field labor or other charges incurred by any customer in removing and/or reaffixing any Keen Pump product, part or component thereof. RETURNED OR REPLACED COMPONENTS: Any item to be replaced under this warranty must be returned to Keen Pump, or such other place as Keen Pump may designate, freight prepaid. This warranty gives you specific legal rights and other rights which may vary from state to state. In the absence of suitable proof of this purchase date, the effective date of this warranty will be based upon the date of manufacture. Example: 05 = Month-Year = January, 05. Sump, Sewage & Effluent Products 16 Keen Pump Company, Inc E State Route 2 East - Ashland, Ohio Fax

2 Contents Alarm Panels Alarm Panel Model No. 152S2-4ALM (115 Volt) 21S2-4ALM (2 Volt) About Us Keen Pump Company, Inc. is headquartered in Ashland, Ohio on 35 acres, having,000 combined square feet of manufacturing and warehouse space. The Research & Development facility has an additional,000 square feet. Keen Pump is a premier designer and manufacturer of Submersible Sewage pumps and Submersible Grinder pumps for the residential, commercial, industrial and municipal markets. The product line follows a proven design for the 1hp through 15hp Grinder Pumps, and Solids-Handling pumps up to 14 discharge (1 HP). Keen Pump is proud to include a complete offering of small sewage, effluent and residential grinder pumps and packages. From 1/3 horsepower to 3 horsepower, Keen Pump has a quality product to fit your application. Most pumps can be configured complete with basin packages engineered and built in our Ashland, Ohio facility. Keen Pump prides itself on full-scale manufacturing of pumps as well as package systems. Keen Pump s intense dedication to producing quality product, delivered on time, backed by reliable service allows us to maintain our confidence to help you select the right pump for your application. Sump/ Effluent Pumps SSE KE KE KE KE Grinder Pumps KGL2... Accessories Table of Contents Basin Package Check Valves Level Controls Alarm Panels Warranty Sewage Pumps KW KW KW... 8 KWR... 9 Sizing Tables Basin Diameters Friction Loss Table Pipe Velocities Alarm Panel Model No. REM-A 8 x 8 x 4 Nema 4X Enclosure Circuit Breaker Receptacle for pump and on/off float and connection for high water float High-water alarm light mounted on top of enclosure with audible alarm with silence switch Quick-Connect seal for running cable and plug from pump and float switch in bottom of enclosure Nema 1 Enclosure Visual and audible alarm with silence switch The KEEN PUMP Difference! Keen Pump Company, Inc. is dedicated to the highest quality of product and service in our industry, along with the best customer care delivered with a sense of warmth, friendliness, individual pride, and company spirit. 2 15

3 Accessories Sump/Effluent Pumps Model SSE33 Level Control Model No. KP-PF (Pump Duty) Float Mechanical Plug-n-go float switches 90 Operating angle - Cord length - Standard 15 amp@1/2 VAC Available with or without Weights Level Control Model No. KP-CF (Control Duty) Float Mercury and Non-mercury float switches available - No plug Narrow angle operation cord length standard (Longer lengths available) 2 1 VAC Available with or without Weights Mounting Clamp - Float KP-FL-CLAMP Easily mount to discharge pipe (3/4-3.5 OD Range) Non-corrosive: SST Band w/ plastic float cord grip Check Valve Model No. CV125-1P (1-1/4 to 1-1/2 ) CV0P (2 ) 1/3 HP ALL Stainless Steel Construction 1-1/4 NPT Discharge Dual Bearings (Upper & Lower) Dual Mechanical Seals Air-Cooled Motor w/ Auto Reset Overload Easily Replaceable Power Cord Vertical Switch (Optional) SSE33A SSE33VA SSE33M Applications: Basement Sumps, Dewatering Capacities: To 35 GPM To TDH Cont. Liquid Temp: 78 F 1/3 HP (34 rpm) Electrical: 115V, 3.5 FLA, 1-Phase, Hz Min. Basin Dia.: 14 Tethered; Vertical Impeller: Stainless Steel - Open Vane Type Solids-Handling: 1/8 Dia. Power Cord: ft. lg. 18 lbs. 1-1/4 or 1-1/2 2-Way Combination 2 Full Flow with Rubber Sleeve Connection ABS body with Stainless Steel Clamps/Fasteners Fits Black, Galvanized or DWV Schedule Pipe

4 Effluent Pumps Basin Packages Model KE33 Basin Packages KWA-BASIN24X24 KE33M KE33A KE33VA Pump Model: KW5M 1/3 HP 1-1/2 NPT Discharge Dual Bearings (Upper & Lower) Mechanical Seal (Silicon-Carbide) Easily Replaceable Power Cord Vertical Switch (Optional) Applications: Basement Sumps, Dewatering Capacities: To 53 GPM To TDH Cont. Liquid Temp: 4 F 1/3 HP (34 rpm) Electrical: 115V, 5.8 FLA, 1-Phase, Hz Min. Basin Dia.: 18 Tethered; 18 Vertical Solids-Handling: 1/4 Dia. Power Cord: ft. lg. 24 lbs. 1/2 HP 2 NPT Discharge Dual Bearings (Upper-Lower) Single Seal (Silicone-Carbide) Easily Replaceable Power Cord HDPE Basin 45 Gallon Capacity Basin/Cover Gas and Odor tight Multiple inlet hub location options Applications: Sewage Capacities: To GPM To 28 TDH Cont. Liquid Temp: 78 F (1 Intermittent) 1/2 HP (34 rpm) Electrical: 115V, FLA, 1-Phase, Hz Operation: Manual w/piggyback on-off Basin Dia.: 24 Solids-Handling: 2 Dia. Power Cord: ft. lg. Pump Weight: lbs. Basin Overall Dimensions: 28 dia. x 24 Deep Inlet Hub Depth: 9.5 in. Package contains: o KW5M 1/2hp Sewage Pump to free-stand on basin bottom (See Page 7 for details) o HDPE basin w/ Anti-flotation collar and poly cover, 24 diameter x 24 deep (Nominal)-45 Gallon Capacity o Cover Fitted w/ 2 Slip discharge flange, 2 npt vent flange, Cord grommets for Pump/floats o (1) Piggyback Pump duty float On-Off for automatic operation º (1) 2 Swing Flapper Check Valve, Non-corrosive material º (1) Pipe Clamp for float - mount to discharge pipe º (1) 2 x 24 long PVC Schedule pipe º (1) 2 Male adapter PVC Schedule

5 Sizing Effluent Pumps Pipe Velocity Chart Model KE4 or KE5 NOTE: If pumping any solids, attempt to design piping system for velocities between 2-5 feet per second. FLOW REQUIREMENTS FOR PIPE VELOCITIES 2-5 FPS (TYPICAL PLASTIC PIPE USED IN INDUSTRY) KE4A KE5A KE4VA KE5VA KE4M KE5M MATERIAL SDR 21 MATERIAL SCHED GPM GPM GPM GPM Nominal Actual Required Required Actual Required Required Pipe Dia. Pipe ID 2 FPS 5 FPS Pipe ID 2 FPS 5 FPS MATERIAL DR-9 MATERIAL DR-11 GPM GPM GPM GPM Nominal Actual Required Required Actual Required Required Pipe Dia. Pipe ID 2 FPS 5 FPS Pipe ID 2 FPS 5 FPS KE4: 4/ HP ; KE5: 1/2 HP 1-1/2 NPT Discharge Dual Bearings (Upper-Lower) Single Seal (Silicone-Carbide) Easily Replaceable Power Cord Vertical Switch (Optional) Applications: Residential Effluent Capacities: To GPM To TDH Cont. Liquid Temp: 78 F (1 Intermittent) 4/ HP or 1/2 HP(34 rpm) Electrical: 115V, FLA, 1-Phase, Hz Min. Basin Dia.: 18 Tethered; 18 Vertical Solids-Handling: 3/4 Dia. Power Cord: ft. lg. 35 lbs. KE5-1/2 HP KE4-4/ HP

6 Effluent Pumps 1 HP, Single or Three-Phase ALL Iron Construction 1-1/2 NPT Discharge 3-Bearings (Upper-Lower-Sleeve) Dual Seals (Silicone-Carbide Lower / Silicone-Carbide Upper) Epoxy-Potted, Power Cord Single-Phase Available w/ Internal Capacitors - No Panel Req d. 1 Model KE2 (High Head Series) KE2C KE2 KE3 Applications: Residential Effluent, Dewatering Capacities: To 65 GPM To 115 TDH Max. Liquid Temp: 1 C Intermittent 1 HP (34 rpm) Electrical: 8/2V, 18 FLA, 1-Phase, Hz 2/4V, 3-Phase, Hz Min. Basin Dia.: 24 Impeller: Ductile Iron - Recessed Type Solids-Handling: 3/4 Dia. Power Cord: ft. lg. 85 lbs NOTE: Select minimum basin depth so 2-1/2 feet of basin depth in gallons = Pump capacity (GPM) NOTE: Velocity and Head Loss Chart for SDR-21 Pipe (Flow Coefficient C = 1) Gallons/Foot Basin Depth Gallons per 2-1/2' Basin Depth Basin Sizing GPM 18" 24" " 36" 48" VERTICAL HEAD IN FEET (LIFT) GATE VALVE CHECK VALVE PUMP/PIPE LAYOUT Velocity / Head (Friction Loss) Chart Flow GPM 1" 1-1/4" 1-1/2" 2" 2-1/2" 3" 4" 6" 8" Q V Hf V Hf V Hf V Hf V Hf V Hf V Hf V Hf V Hf * * * * * * * * * The values above based on average internal diameter of pipe, formula V = Q/A and the Hazen-Williams formula. V = Velocity (Feet per second) Hf = Head Loss (Feet per feet of pipe) Q = Flow in Gallons per minute * MINIMUM GPM and velocity per pipe size for liquids containing solids. Sizing 6 11

7 Grinder Pumps Sewage Pumps Model KGL Model KW4 or KW5 KGL1-115 KGL2-115 KGL2-21C KHGL2-21C KW4A KW5A KW4VA KW5VA KW4M KW5M 1 or 2 HP 1-1/4 NPT Removable Discharge Flange 3-Bearings (Upper-Lower Ball & Sleeve) Dual Seals (Silicone-Carbide) Epoxy-Potted, Power Cord Available w/ Internal Capacitors - No Panel Req d. Cutter Assembly consists of: Hardened (Rockwell 58-) SST stationary shredding ring and rotating cutter. Easily macerates solids into fine slurry. 1 Applications: Residential Sewage Capacities: To 43 GPM To 1 TDH Max. Liquid Temp: 1 C Intermittent 1 or 2 HP (34 rpm) Electrical: 115V or 2V, 1-Phase, Hz Operation: Manual Min. Basin Dia.: 24 Impeller: Ductile Iron - Recessed Type Solids-Handling: Macerates Solids into Fine Slurry Power Cord: ft. lg. 90 lbs. KW4: 4/ HP ; KW5: 1/2 HP 2 NPT Discharge Dual Bearings (Upper-Lower) Single Seal (Silicone-Carbide) Easily Replaceable Power Cord Vertical Switch (Optional) Applications: Sewage Capacities: To GPM To 28 TDH Cont. Liquid Temp: 78 F (1 Intermittent) 1/2 HP (34 rpm) Electrical: 115V, FLA, 1-Phase, Hz Min. Basin Dia.: 18 Tethered; 18 Vertical Solids-Handling: 2 Dia. Power Cord: ft. lg. lbs. 1 KHGL2-21C 25 KGL2-21C KGL KW5-1/2 HP KW4-4/ HP 0 0 7

8 Sewage Pumps Sewage Pumps Model KW (Single-Vane Impeller) Model KWR KWM2-21 KW15M2-21 KWM2-21 KWM2-23 KWM2-43 KW15M2-23 KW15M2-43 KWM2-23 KWM2-43 KWM2-23 KWM2-43 KWR5-01 KWR5-21 KWR-01 KWR-21 KWR5-03 KWR5-23 KWR5-43 KWR-03 KWR-23 KWR-43 1, 1-1/2, 2, 3 HP Stainless Steel Keyed Shaft 2 or 3 NPT Discharge Dual Bearings (Upper-Lower) Dual Seals (Silicone-Carbide / Upper) (Lip Seal / Lower) Epoxy-Potted, Power Cord Applications: Sewage Capacities: To 325 GPM To 95 TDH Max. Liquid Temp: 1 C Intermittent 1, 1-1/2, 2, 3HP (34 rpm) Electrical: 1-2HP (8/2V) 1-Phase 1-3HP (2/4V) 3-Phase Operation: Manual Min. Basin Dia.: 24 Impeller: Cast Iron - Single-Vane Type Solids-Handling: 2 Dia. Power Cord: ft. lg. lbs. 1/2, 1 HP HAZARDOUS Location Construction FM Approval Pending 2 or 3 NPT Discharge 3-Bearings (Upper-Lower-Sleeve) Dual Seals (Silicone-Carbide / Upper) (Silicone-Carbide / Lower) Epoxy-Potted, Power Cord Applications: Sewage Capacities: To 175 GPM To 33 TDH Max. Liquid Temp: 1 C Intermittent 1/2, 1HP (17 rpm) Electrical: 1/2-1HP (8/2V) 1-Phase 1/2-1HP (2/4V) 3-Phase Operation: Manual Min. Basin Dia.: 24 Solids-Handling: 2 Dia. Power Cord: ft. lg. lbs. 1-Phase 3-Phase KW - 2 HP KW - 1 HP KW15-1-1/2 HP KW - 1 HP KW - 3 HP KW - 2 HP KW15-1-1/2 HP KWR - 1 HP KWR5-1/2 HP