1000-Watt Energy Center

Transcription

1 1000-Watt Energy Center OPERATING INSTRUCTIONS Patent Pending

2 Sierra Wave 1000-Watt Energy Center #9675 The Sierra Wave 1000-Watt Energy Center is a heavy duty and efficient portable power center offering 1000 watt hours of rechargeable power bringing portable energy to your home, office, or job site. Whether it is used as a backup power supply for areas experiencing power outages due to natural disaster or as a mobile generator for a campsite, the Energy Center powers your world. Charge it from available electricity or operate self-sufficiently using one of the Sierra Wave Solar Collectors. No set-up is required, just plug in and go. Includes a 120V AC wall charger. The Energy Center uses LiFePO4 (lithium iron phosphate) battery technology. This battery type offers a long life cycle and reliable performance. Couple that with a linear power management system to make the Energy Center the most advanced portable power system on the market. IMPORTANT WARNINGS & SAFEGUARDS Read all instructions thoroughly before operating this unit to avoid injury to self or property and to avoid damaging the unit. Keep instructions handy for reference during use. ENERGIZED EQUIPMENT - ELECTRICAL SHOCK & EXPLOSION HAZARDS GENERATES LETHAL VOLTAGES Do not submerge in liquid or operate in wet environments. Device is not waterproof or water resistant. Operate in dry environments only. Do not operate in flammable or explosive environments Do not operate if the unit is damaged in any way including loose electronics or if charging cords are frayed and wires are exposed. Do not plug inverter 120V AC outlets into external 120V AC outlets of any kind Do not place foreign objects inside the power outlets Do not disassemble. There are no user serviceable parts. Contact the manufacturer for all repairs. Do not use any AC powered devices over 1000W for risk of damage to the batteries or inverter Monitor battery regularly during charging Do not use to operate any medical life support equipment Consult your physician before using with CPAP devices or other non-life support medical equipment Do not block the air inlets or vents Do not replace fuses with larger amperage values Not recommended for use or storage below 14º (-10ºC) or above 120ºF (49ºC). Place out of direct sunlight to prevent overheating. Administer close supervision when operating around children or persons with disabilities Check dangerous goods shipping regulations before shipping DANGER: Contains lithium high-energy batteries. Follow all precautions to prevent injury, property damage and fire at all times during storage and operation. Never store or use in temperatures above 120 F (49 C) Keep away from sparks, open flames and heat sources Do not drop, puncture or incinerate Stop use immediately if you notice a leak or damage to the battery or unit. If it malfunctions contact Customer Service at Follow your local battery disposal regulations 2

3 THE ENERGY CENTER IS ONLY SERVICEABLE BY AN AUTHORIZED REPAIR FACILITY. DO NOT DISMANTLE. WARRANTY IS VOID IF THE DEVICE IS OPENED BY UNAUTHORIZED PERSONNEL. CALL AERVOE INDUSTRIES, INC. AT FOR REPAIR INFORMATION. The limited warranty described in the warranty is the sole and exclusive warranty provided by Aervoe Industries, Inc. In no event will Aervoe be liable for any indirect or incidental damages or losses of any kind arising from or as a result of misuse or abuse, or the incorrect installation or operation of the product. FCC REQUIREMENTS Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/tv technician for help Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 3

4 PARTS IDENTIFICATION Inverter Exhaust Fan Solar Input LED Solar IN DC IN Solar Charge Complete LED POWER IN 120V AC CHARGER ANDERSON TO MC4 ADAPTER CABLE 4

5 220V AC Outlet Status LEDs Volt/AMP Meter Earth Ground Inverter ON/OFF DC ON/OFF Battery Meter ON/OFF 12V DC Outlets 12V DC Fuses Battery Meter USB Ports Main Power Keyhole POWER OUT MAIN POWER KEY 5

6 CHARGING For maximum efficiency and battery life, charge before first use and after each use. Charge the batteries every 3-6 months if it is being stored for a long period of time. Failure to properly charge as listed below could damage the unit and affect performance. Two methods of charging are available: Use the included 120V/220V 15V 10A AC Charger Use a compatible solar panel (Sierra Wave #9580 & #9590 Solar Collectors recommended) Main Power Key: Turning clockwise (ON) allows all charging and operation features. Turning counterclockwise (OFF) disengages all operations. It should be in the OFF position during charging. The key should be removed when not in use. AC Charging: (included) 1. The MAINPOWER KEY should be in the OFF position and the INVERTER ON/OFF switch and the DC ON/OFF switch should be OFF. 2. Plug the AC Charger into the DC IN socket. Make sure that the charger input voltage selector is set for your area this is either 120V or 220V. 3. Find a suitable 120V AC outlet and plug in the power cord. 4. CHARGING INDICATORS: The RED LED on the charger will glow when charging is in progress. The GREEN LED on the charger will glow and the RED LED will turn off when the battery is completely charged. 5. The BATTERY METER will indicate the strength of the battery All 10 LEDs means the unit is fully charged. Recharge as needed. 6. Disconnect the charger once charging is complete. Solar Charging: (solar panel not included) The Energy Center has a built in Linear Solar Charge Controller that can accept 12V and 24V solar panel systems, up to a maximum input of 150 watts. Aervoe recommends the Sierra Wave # Watt Solar Collector or the Sierra Wave # Watt Solar Collector. An ANDERSON TO MC4 ADAPTER CABLE is provided to connect Sierra Wave solar panels, or other compatible collectors, directly into the Energy Center. # ft. Extension Cable is available if a longer cord is needed in order to keep the #9675 indoors while charging. 1. Follow instructions provided with the solar panel. 2. Connect the MC4 cables on the solar panel to the included MC4 ADAPTER CABLE and the plug the ANDERSON plug into the SOLAR IN socket. If using a solar panel or adapter cable other than Sierra Wave, observe the proper +/- polarities and wattage recommendations. IMPORTANT: do not connect to the DC IN port as a malfunction can occur. 3. When solar voltage is present, the SOLAR INPUT LED will glow RED. 4. When charging is complete the SOLAR CHARGE COMPLETE LED will glow GREEN. 5. The BATTERY METER will indicate the status of charging All 10 LEDs means the unit is fully charged. Recharge as needed. 6. Disconnect the solar collector once charging is complete. 6

7 Note: The BATTERY METER measures the battery voltage in a range of approximately 10.5 to 14.5 volts. When a charging voltage is present the BATTERY METER will indicate the charging voltage level, not the battery voltage. When voltage sources are removed, the Meter will again indicate the battery voltage level. The BATTERY METER can be left on to monitor the battery voltage levels during charging or power center operation. It should be switched OFF when not in use or during long term storage. OPERATING INSTRUCTIONS Once charged, the Energy Center is ready to use. All power outputs may be used simultaneously as long as the total peak wattage draw of all devices plugged in does not exceed 1000W. Check all device specifications to make sure they are compatible with the Energy Center. For long battery life and maximum recharge cycles, it is best to keep the total of all power output loads in the W range or lower. Running at maximum output at all times may overheat the inverter and will severely reduce the life of the battery. MAIN POWER KEY must be removed before storage or transportation. 120V AC, 60Hz Power Operation (Pure Sine Wave Inverter) The 120V AC operation can safely power common AC appliances and devices rated at up to 1000W Peak. 1. Turn off the INVERTER ON/OFF switch and remove MAIN POWER KEY before plugging in any appliance into the 120V outlet. 2. Turn on the MAIN POWER KEY and switch the INVERTER ON/OFF to on. The GREEN LED will illuminate indicating that AC power is available and operating normally. This LED will stay lit during use. 3. Monitor the battery meter voltage and wattage during use. The RED (fault) LED indicates the inverter has shut down caused by low or high battery voltage, overload, or excessive heat. The RED LED blinks for a few seconds during a normal power up sequence. Turn the Inverter OFF, wait a few seconds, and turn it ON again to reset any faults. 4. Volt/Amp Meter: Continually displays the current battery voltage and the peak amperage draw. The operating range is approximately 10.5V DC to 14.5V DC. Note: When the battery voltage is reduced below 10.5V the inverter will sound an alarm and the RED LED will glow. Switch the inverter OFF and recharge the batteries using the procedures described in the Charging Section on page 6. GROUNDING: An EARTH GROUND lug is provided if the power inverter will be used to power a permanent electrical fixture. The ground wire should be connected to a building electrical ground point. If the power inverter will be used as a temporary power source, the ground point may be connected to a chassis ground point, for example a ham radio transceiver ground terminal. 7

8 DC Power The DC power operation includes a DC ON/OFF switch that when switched ON provides power to the USB ports and the 12V DC sockets. When the battery voltage is within the operating voltage range the Green LED on the DC power switch will glow. USB OPERATION: 1. Turn the MAIN POWER KEY and the DC power switch to the ON position. 2. Plug in your USB device or USB charging cable. Two 5V/2A devices may be plugged into the USB charge ports and operated simultaneously. 3. Monitor the battery meter voltage and wattage during use. 4. Disconnect and turn the power off when not in use. 12 VOLT DC OPERATION: 15A/150 watt each outlet max. 1. Turn the MAIN POWER KEY and DC power switch to the ON position. 2. Plug in your 12V device s power or charging cable into either of the 12V sockets. 3. Monitor the battery meter voltage and wattage during use. 4. A 15A protection fuse is installed at each power outlet. Replace with the same specification fuse if needed. 5. Disconnect and turn the power off when not in use. Note: When the battery voltage is reduced below 10.5V all DC outputs will automatically switch OFF and the GREEN LED on the DC ON/OFF switch will no longer be ON. Recharge the batteries using the procedures described on page 6. 8

9 CARE AND MAINTENANCE Dust regularly with a clean dry cloth to prevent dust and dirt from building up on the vents and power inputs/outputs Store in a clean, dry place when not in use Charge after each use, every 3 months, and before storing so it is ready to use when needed Turn the INVERTER ON/OFF, DC ON/OFF and BATTERY ON/OFF switches OFF and remove the MAIN POWER KEY when not in use or before long term storage TROUBLESHOOTING If your Solar Link fails to operate as specified, follow these troubleshooting steps to correct the issue. If you still experience issues, please contact Aervoe Industries, Inc. at or Make sure the MAIN POWER KEY is inserted and ON. Charging Issues Ensure all charging cords (10A AC or solar panel) are connected securely Check power indicators on chargers and the Solar Link to make sure they are operating If using a solar collector to charge, ensure it is correctly positioned in direct sunlight 12V DC Output Failure Check the BATTERY METER to see if the Solar Link has sufficient battery charge available. If not, follow the charging steps previously described on page 6. Ensure the DC ON/OFF switch is ON and the green light is ON Check to make sure that the 12V DC circuit protection fuse is not blown by removing the 15A FUSE associated with the suspect 12V DC output plug. Inspect the fuse and replace if needed with the same size and amperage rated fuse. Check the 12V DC outlet for obstructions or other visible damage Verify the device being charged is working and not damaged 120V AC Output Failure Check the BATTERY METER to see if the Solar Link has sufficient battery charge available. If not, follow the charging steps previously described on page 6. Ensure the INVERTER ON/OFF switch is ON and the green LED is ON Check the 120V AC outlet for obstructions or other visible damage Verify that the device being powered is working and not damaged USB Output Failure Check the BATTERY METER to see if the Solar Link has sufficient battery charge available. If not, follow the charging steps previously described on page 6. Ensure the DC ON/OFF switch is ON and the green light is ON Check the USB port for obstructions or other visible damage Verify the device being charged is working and not damaged 9

10 TECHNICAL INFORMATION SPECIFICATIONS BATTERY TYPE LiFePO4 (lithium iron phosphate) 80Ah V BATTERY LIFESPAN PROTECTION CIRCUIT SOLAR CHARGE CONTROLLER 120V/60Hz INVERTER SPECIFICATIONS Output Wave Form AC Output Power (continuous) AC output (peak) AC Output Voltage AC Output Frequency cycles (cycle = charge and discharge) 80% Depth of discharge Built-in over voltage, self-discharge, reverse polarity, and short circuit protection Built in 12V/24V 150W Linear Solar Charge Controller with over voltage, over current and reverse polarity protection Pure Sine Wave 1000 Watts 2000 Watts V AC 60 Hz INVERTER SAFETY FEATURES Electronic overload protection with automatic shutdown Built-in internal backup DC fused provides added safety Low battery voltage warning followed by automatic shutdown Over temperature protection with automatic shutdown Output short circuit protection FUSES (replaceable) DC INPUT POWER 120V AC WALL CHARGER (INCLUDED) Replacement Charger 15A fuse (12V DC outlet) 15V 10A max, 150W Input: 120V AC, V, 50/60hz, 100VA Output: 14.6V-15V DC, 10A C-UL, FCC approved # V AC Charger RATED OUTPUT POWER 120V AC, 60hz, 1000w watts max PURE sine wave inverter, 740 watt-hours 12V DC - 15A, 820 watt-hours USB (5V-2A) - 3 ports, 820 watt-hours OPERATING TEMPERATURE DIMENSIONS WEIGHT 32ºF TO 113ºF (0ºC TO 45ºC) 15 x 14 x 9 (381 x 355 x 228mm) 53 lbs. (24Kg) CERTIFICATIONS Pending FCC Part 15 Pending UL

11 CHARGE TIME Using # Watt Solar Collector Using # W Solar Collector Using 120V AC Wall Charger Solar charging time based on a bright, sunny day hours 8-10 hours 6-8 hours SAMPLE RUN TIMES Times vary depending on user settings. #6905 Max Burton Digital Stove To Go 5-6 hours 9720/9721 Sierra Wave Portable Area Light 1 Light hours, 3 Lights hours 30 Television hours Small thermo refrigerator Large refrigerator Small microwave (<1000 watts) Small power tools (drills, jig saw, sander) Laptop (65-90 watts) Smartphone Tablet computer 8-10 hours 2-4 hours from room temperature 15+ hours at set temperature up to 30 minutes 2-10 hours 6-8 hours Recharge > 70 times Recharge > 35 times To estimate how many hours of power are in the Solar Link, find the watt hour draw of the device that you wish to power and divide into 740W (120V AC) or 820W (USB & 12V DC). (EX: One 12V 10-watt light = 82 hours of continuous light). Lower run times may result when using devices above 600 watts. 1-year performance warranty on all products from date of purchase. Report to home office or local Aervoe representative for examination. Because Seller cannot control Buyer s handling or use of product, Seller makes no warranty expressed or implied when not used or stored in accordance with directions. This warranty is limited to repair or replacement of product within 30 days of receipt at the Aervoe office in Gardnerville, NV and on original purchase only. AVAILABLE ACCESSORIES Available at your local retailer or #9580 Sierra Wave 80-Watt Solar Collector #9590 Sierra Wave120-Watt Solar Collector 11

12 9675inst; cs1/16 AERVOE INDUSTRIES, INC. Gardnerville, NV