ANNEXURE XI. (Ni Cd Battery Bank) TECHNICAL SPECIFICATIONS OF 125V STATION BATTERY BANK OF GTG I.
|
|
- Benjamin Doyle
- 5 years ago
- Views:
Transcription
1 ANNEXURE XI (Ni Cd Battery Bank) TECHNICAL SPECIFICATIONS OF 125V STATION BATTERY BANK OF GTG I. Sr. No Technical Particulars Confirmation to be given by bidder (Please strike out which ever not applicable) 1 Capacity 210 AH AT 25 C 2 No. of cell Type of Battery Medium Discharge Performance Pocket type, Alkaline 4 Nominal Voltage Floating Charge Voltage Final Discharge Voltage Equalising Charge Voltage Max. Charging Current 42 Amp. 9 Battery Stand Not Required. Vendor Name: Vendor Address: Vendor Phone No: Vendor Mobile No: Authorized Signatory Sign: Authorized Signatory Name: Stamp/ Seal: Dated: Vendor Fax No: Vendor E Mail Id:
2 ANNEXURE XII Sr. No Technical Particulars Confirmation to be given by bidder (Please strike out which ever not applicable) 1 Scope:- The scope of Stationary type Alkaline Storage Battery for 125 Volts, 210 AH Battery Bank for GTG I Covers Manufacture. Testing at works before Dispatch and Delivery for Destination. It also includes installation, first initial charging at site and commissioning. 2 Service:- The Battery units are required to provide 125V DC control supply for GTG I 3 Standards: The equipment shall be supplied to the relevant IEC / Indian Standards. Any deviations shall be indicated with the salient points. 4 Site Conditions:- The Climate can be described as wet and tropical. Temperature Range : -1.1 to 45 C Electrical ground resistivity : 30 to 40 Ohm-Meter. Relative Air Humidity : 100% Max. Site above MSL : Less than 1000 Meter. The atmosphere in the factory shall be laden with urea dust. The Air may contain Ammonia Vapours. 5 Battery SPECS:- 5.1 The battery bank shall consists of series connected Ni-Cd cells as specified. 103 Nos., 210 AH, KPM 210, 125V GTG - I Battery Bank. 5.2 The battery cells shall confirm to the following requirements. a. The cells shall be vented type, assembled in plastic containers with covers. Covers shall be fitted with spray proof vent plugs. b. All cells terminals shall have adequate current carrying capacity. Cell terminal posts shall be equipped with connector bolts. Cell terminal posts, bolts, and associated hardware shall be of electrolyte resisting material. c. Electrolyte level Indication lines for minimum and maximum levels shall be marked on the maintenance access side of each jar or container. 5.3 Each battery shall be rated for specified ampere hours at the Five Hrs., rate discharge to an end voltage of 1.00 Volts per cell. Page: 1 of 3
3 5.4 Each cell shall be contained in a closed top container preferably transparent and unbreakable and shall incorporate positive and negative plates and separators in position. Wooden separators shall not be acceptable. These Cells shall be provided with Inter cell connectors, nut bolts along with 2 flat & 1 spring washers. Connector must be suitable to take full current and should be designed to withstand short circuit current also. Interrow, Inter Tier Connectors and take off terminals shall be designed for rated current and shall also be able to withstand shot circuit current. All these Connectors shall be manufactured from Electrolytic Copper, with Nickel Plating and shall be Electrolyte Resistant. 5.5 The battery units shall be complete with all necessary components such as lids, plugs, separators and buffers, inter-cell connectors, cell insulators. 5.6 The required quantity of electrolyte plus 10% extra quantity complying with relevant standards shall be supplied in suitable non-returnable containers along with the battery. 5.7 Accessories for maintenance to be supplied at no extra cost to NFL: a. Syringe type hydrometer suitable for specific gravity readings 4 Nos. b. Thermometer with specific gravity correction scale 2 Nos. c. Cell testing Voltmeter (3-0-3) complete with leads 2 Nos. d. Insulated spanners (for each type of Battery) 2 Sets e. Rubber syringe 2 Nos. f. Funnel 2 Nos. g. Jug 2 Nos. h. Apron 2 Nos. i. Rubber Gloves 2 Sets j. Teak wood stand for Hydrometers. 2 Nos. 5.8 Spares to be supplied at no extra cost to NFL: Battery Set shall be supplied with following spares at no extra cost to NFL i. Intercell Connector 10 Nos. ii. Vent Plugs 10 Nos. iii Nuts bolts & Washers ( 2 flat & 1 spring washer) 10 Nos. iv. Uncharged Dry Battery 01 Nos. 6.0 TEST The tests specified in the relevant standards shall be carried out during the course of manufacturing of battery. The test certification for various tests conducted shall be furnished to the inspection. Acceptance test on 1 sample of battery shall be carried out at works. At lest 2 weeks advance notice of the date of inspection shall be given to purchaser. The equipment shall be despatched in single lot only after approval of the test certificates by inspection. However, during commissioning of the battery set a representative of the supplier shall be present at NFL Vijaipur Site to carry out the capacity test on the battery bank. 7.0 DOCUMENTS:- a. Documents, test certificates, drawing etc along with Operation & Maintenance manuals. Complete Charging, Initial Charging, Discharging Procedure shall be supplied in Four Sets along with dispatch documents at no extra cost to NFL. b. Technical Particulars: Complete technical particulars shall be furnished along with the offer as per Annexure-IX and in absence of these particulars offer shall not be evaluated. Page: 2 of 3
4 8.0 You will submit Guarantee Certificate as per Standard Clause given in NIT. The Guarantee shall cover:- i. High reliability under normal continuous operating and fault condition. ii. All ratings under continuous operating condition. iii. Compliance with the specifications as well as with specified norms and standards. iv. That all the necessary spare parts can be made available to the purchaser. v. That all equipment is constructed in such a manner that repair and revision are kept at a minimum and can be carried out with the shortest possible time. vi. Within specified period of guarantee, the supplier shall replace any faulty materials, equipments and render service without any additional costs or delay. 9.0 Documentation for 125V Ni Cd Battery for GTG 1 as per Annexure X Vendor Name: Vendor Address: Vendor Phone No: Vendor Mobile No: Authorized Signatory Sign: Authorized Signatory Name: Stamp/ Seal: Dated: Vendor Fax No: Vendor E Mail Id: Page: 3 of 3
5 ANNEXURE XIII Page: 1 of 2 Sr. No Technical Particulars Confirmation to be given by bidder 1. Manufacturer s Name 2. Country of manufacture 3. Type of Battery 4. Reference standard for Construction & Performance 5. Number of Cells 6. Nominal Voltage of Battery 7. Finishing rates of charge (Amps) : 8. Voltage per cell at the end of charge at the finishing rate 9. Voltage of each cell on complete discharge at 5 Hr. rate 10. Open circuit voltage of battery bank of full charge (Volts) 11. Internal resistance per cell at `C (Mill Ohm/Cell) 12 Minimum Voltage per cell at Which at can be operated safely at 5 Hr rate of Discharge 13 Requirement for first charge (AH): 14 Discharge capacity in Ampere Hour at a) 5 Hour rate to 1.14 Volts per cell: b) 3 Hour rate to 1.10 Volts per cell c) 1 Hour rate to 1.06 Volts per cell d) 30 Minutes discharge rate to 1.00 Volts per Cell e) 15 Minutes discharge rate to 0.85 Volts per cell f) 5 Minute discharge rate to 0.65 Volts per cell g) 1 Minute discharge rate to 0.65 Volts per cell 15 Guaranteed efficiencies on 10 Hour rate (AH) watt Hour 16 Type of positive plated per cell 17 No. of positive plates per cell 18 Type of negative plates 19 Size of Positive plates 20 Size of negative plates 21 Fully charged specific gravity of the electrolyte 22 Full charged specific gravity of the electrolyte 23 Slow charging rate (Ampere) 24 Quick charging rate (Ampere) 25 Float charging voltage per cell (V/cell) 26 Size and material of connectors and method of connection between cells a) Inter-cell b) Inter-low c) Inter-stand d) Take-off e) Stud/bolts, nut & weather 27 Type of separators 28 Thickness of separators 29 Material & size of containers (mm) Length : Width : Height : 30 Thickness of containers (mm) 31 Clearance between the bottom of plates and container (mm) : 32 Amount and specific gravity of electrolytes per cell required for the first filling (liters/cell) 33 Weight of cell complete with electrolyte (mm) :
6 Page: 2 of 2 34 Shelf Life 35 Expected Life a) For Cyclic use (In Terms of no. of Charge/Discharge) b) For use under float (Trickle Charge) 36 Operating Temp Range Note: Whichever required, exact dimensions are to be mentioned. Words like `adequate sufficient shall not be acceptable. Vendor Name: Vendor Address: Vendor Phone No: Vendor Mobile No: Authorized Signatory Sign: Authorized Signatory Name: Stamp/ Seal: Dated: Vendor Fax No: Vendor E Mail Id:
SPECIFICATIONS OF Ni-Cd BATTERY BANK
SPECIFICATIONS OF Ni-Cd BATTERY BANK ANNEXURE-Z Supply, Installation and commissioning of Ni-cd battery bank for high rate of discharge type KPH 125V 210 AH consisting of 103 number of cells. Detail technical
More informationGUJARAT ENERGY TRANSMISSION CORPORATION LTD. TECHNICAL SPECIFICATIONS. 110 V, 100 Ah / 250 Ah & 220 V, 250 Ah / 350Ah TUBULAR LEAD ACID BATTERY SETS
GUJARAT ENERGY TRANSMISSION CORPORATION LTD. SARADAR PATEL VIDYUT BHAVAN, RACE COURSE, BARODA 390 007. TECHNICAL SPECIFICATIONS FOR 110 V, 100 Ah / 250 Ah & 220 V, 250 Ah / 350Ah TUBULAR LEAD ACID BATTERY
More informationSPECIFICATIONS FOR 50 V, 600 AH LEAD ACID BATTERY
(I) INTRODUCTION: Power Line Carrier Communication (PLCC) System is being used by Gujarat Energy Transmission Corporation Ltd. for Speech, Data, Protection and Teleprinter signal transmission purpose throughout
More informationTECHNICAL SPECIFICATION FOR 30 V, 100 AH STATIONARY BATTERIES AND BATTERY CHARGING EQUIPMENT. (SPECIFICATION NO. MSEB/Dist/IV/2004.
TECHNICAL SPECIFICATION FOR 30 V, 100 AH STATIONARY BATTERIES AND BATTERY CHARGING EQUIPMENT (SPECIFICATION NO. MSEB/Dist/IV/2004.) MAHARASHTRA STATE ELECTRICITY DISTRIBUTION COMPANY LTD. PAGE 1 OF 18
More informationSection V DC Nickel Cadmium Alkaline BATTERY
Section - 7 TECHNICAL SPECIFICATION OF 110V DC Nickel Cadmium Alkaline BATTERY TECHNICAL SPECIFICATIONS & REQUIREMENTS OF 110V DC Nickel Cadmium Alkaline Battery 7. 1 GENERAL This section of the document
More informationSPECIFICATION FOR REWIRABLE FUSES (KITKAT FUSES) 100A & 200A SPECIFICATION NO.: DIST/ A- KIT /
SPECIFICATION FOR REWIRABLE FUSES (KITKAT FUSES) 100A & 200A SPECIFICATION NO.: DIST/ A- KIT / 2005-06 SR.NO ITEM PAGE 1. SCOPE 2 2. WEATHER CONDITIONS 2 3. RATED VOLTAGE & FREQUENCY 2 4. GENERAL REQUIREMENT
More informationKPM type Intended for medium discharge currents from 0.5 to 2 C
KPM type Intended for medium discharge currents from 0.5 to 2 C APPLICATION: -Railway: Traction cars, VIP cars, etc. -Mines: Mining locomotives -Factories and institutions: Electro-carets, certain types
More informationTender documents for supply, erection & commissioning of Plante Type Battery to 2x210 MW IB Thermal Power Station.
ORISSA POWER GENERATION CORPORATION LIMITED IB THERMAL POWER STATION AT/P.O: BANHARPALI, DIST: JHARSUGUDA, PIN: 768234 (ORISSA), INDIA GRAM: IB THERMAL, TEL: 06645-222209/222210, FAX: 06645-222209/54/30
More informationCITY OF CHARLEVOIX REQUEST FOR BIDS WESTENBROEK SUBSTATION 48VDC BATTERY BANK
CITY OF CHARLEVOIX REQUEST FOR BIDS WESTENBROEK SUBSTATION 48VDC BATTERY BANK The City of Charlevoix is requesting bids for the furnishing and delivery (F.O.B. project material site, Charlevoix, Michigan)
More information020: 2013 CEB SPECIFICATION MINIATURE CIRCUIT BREAKER (MCB)
020: 2013 CEB SPECIFICATION MINIATURE CIRCUIT BREAKER (MCB) CEYLON ELECTRICITY BOARD SRI LANKA Telephone: +94 11 232 0953 Fax: +94 11 232 3935 CONTENTS Page 1.0 Scope 3 2.0 System Parameters 3 3.0 Service
More information013 : 2009 CEB SPECIFICATION MOULDED CASE CIRCUIT BREAKERS
013 : 2009 CEB SPECIFICATION MOULDED CASE CIRCUIT BREAKERS FOR OVERHEAD NETWOKS CEYLON ELECTRICITY BOARD SRI LANKA Specification for MOULDED CASE CIRCUIT BREAKERS FOR OVERHEAD NETWOKS CEB Specification
More informationSPECIFICATION FOR POWER BATTERIES
KAKRAPAR ATOMIC POWER STATION UNITS & (0 MWe) PROCUREMENT SPECIFICATION NO. KAPS/534/PB SEPC./00 SPECIFICATION FOR POWER BATTERIES Prepared By: Checked By: Reviewed By: Approved By: Kapil Mishra SO/E,
More information017: 1998 CEB STANDARD RING MAIN UNIT CEYLON ELECTRICITY BOARD SRI LANKA
017: 1998 CEB STANDARD RING MAIN UNIT CEYLON ELECTRICITY BOARD SRI LANKA CONTENTS PAGE 1. Scope 2 2. System Parameters 2 3. Service Conditions 2 4. Applicable Standards 3 5. Basic Features 4 6. Quality
More informationHARYANA VIDYUT PRASARAN NIGAM LTD.
HARYANA VIDYUT PRASARAN NIGAM LTD. TECHNICAL SPECIFICATION SSD/S-03/R-1/DGM-605 TECHNICAL SPECIFICATION FOR 33 KV CAPACITOR BANKS CHIEF ENGINEER/MM HVPNL, PANCHKULA TELEPHONE & FAX: 0172-2583724 MARCH-2017-0
More information4.1 Type of the valve and materials of construction of body and trim shall be as specified in valve Data sheet.
SHEET 1 OF 5 1.0 GENERAL & SCOPE 1.1 This specification covers the design, material, construction features, manufacture, inspection & testing, Painting and packing requirements of Spring Loaded Bypass
More informationCAMTECH/S/2005/LAC/2.0 1 LEAD ACID CELL
CAMTECH/S/2005/LAC/2.0 1 1. Introduction LEAD ACID CELL Two different types of lead acid cells are manufactured by the industry and depending on the application, these are normally referred to as mobile
More informationNi-Cd Batteries. Solutions for the toughest requirements
I N T E L L I G E N T S Y S T E M S Ni-Cd Batteries Solutions for the toughest requirements Triathlon Ni-Cd Batteries cell Construction Gas drying or flame arresting vent Safety terminal Redundant leak
More informationNCPP. Nickel Cadmium Pocket Plate Batteries. Single Cell Catalogue
NCPP Nickel Cadmium Pocket Plate Batteries Single Cell Catalogue Introduction: HBL s Nickel Cadmium Pocket Plate battery designs are based on the superior pocket plate technology. A fully integrated modern
More informationVRLA Batteries. Battery Installation And Start up Guide
TECHNICAL MANUAL 41-7525 VRLA Batteries 26-206 Ampere-Hour Capacity Battery Installation And Start up Guide (For Rack Mounted Systems) 41-7525/0514/CD www.cdtechno.com Table of Contents 12V VRLA Battery
More informationSPECIFICATION FOR AUTOMATIC PRIMING AND OPERATING SYSTEM FOR CENTRIFUGAL PUMPS.
DRAFT SPECIFICATION NO : RDSO/PE/SPEC/D/PS/0010-99 (REV. 0 ) SPECIFICATION FOR AUTOMATIC PRIMING AND OPERATING SYSTEM FOR CENTRIFUGAL PUMPS. 0. FOREWORD 0.1 This specification covers manufacturing and
More informationMaterial Description Quantity UOM
Page : 1 / 8 OIL INDIA LIMITED Fax-91 0361 2643686 (A Govt. of India Enterprise) Email-oilmatpl@oilindia.in Udyan Vihar, Narengi, Guwahati, Assam 10 99070701 BATTERY 12 V 65AH Sealed Maintenance Free (SMF)
More informationLDP MP. Ni-Cd single cells. LD P - M P ranges Capacity: 10 Ah to 70 Ah L2.4. Benefits
L2.4 Ni-Cd single cells LD P - M P ranges Capacity: 10 Ah to 70 Ah LDP MP Nickel-cadmium single cells are designed for general purpose applications, where maximum operating reliability is a key factor:
More information023 : 2006 CEB STANDARD. 12kV & 36kV LOAD BREAK SWITCHES CEYLON ELECTRICITY BOARD SRI LANKA
023 : 2006 CEB STANDARD 12kV & 36kV LOAD BREAK SWITCHES CEYLON ELECTRICITY BOARD SRI LANKA Specification for 12kV & 36kV LOAD BREAK SWITCHES CEB Standard 023 : 2006 CEYLON ELECTRICITY BOARD No. 50, Sir
More informationTECHNICAL SPECIFICATIONS FOR 11KV AIR BREAK (A.B.) SWITCHES :
TECHNICAL SPECIFICATIONS FOR 11KV AIR BREAK (A.B.) SWITCHES : 1. SCOPE : This specification covers design, manufacturing, testing at manufacturer s works, inspection, packing & delivery of 11 KV Air Break
More informationVentPro Reduced Maintenance Nickel Cadmium Batteries for Stationary Applications
VentPro Reduced Maintenance Nickel Cadmium Batteries for Stationary Applications Dimensional and Electrical Data Rev. 02-16 Storage Battery Systems LLC N56 W16665 Ridgewood Dr. Menomonee Falls, WI 53051
More informationPOWER-plus. Ni-Cd XHP. Capacity: 10 Ah to 250 Ah
Ni-Cd XHP Capacity: 10 Ah to 250 Ah XHP Range Low maintenance, high performance Ni-Cd batteries Powerful assurance for critical applications Depend upon XHP series where vital UPS, engine starting and
More informationNCPP. Nickel Cadmium Pocket Plate Batteries. Single Cell Dimensional and Electrical Data
NCPP Nickel Cadmium Pocket Plate Batteries Single Cell Dimensional and Electrical Data Nickel Cadmium Pocket Plate Batteries HBL's Nickel Cadmium Pocket Plate Battery designs are based on the superior
More informationSPECIFICATION FOR VT D 70 CONTENTS
CONTENTS 1/ SCOPE 2/ GENERAL ELECTRICAL CHARACTERISTICS 3/ GENERAL MECHANICAL CELL SPECIFICATION 4/ CAPACITY 5/ CHARGE RECOMMENDATIONS 6/ CYCLE LIFE 7/ CELL AND BATTERY MANAGEMENT 8/ SPECIFICATION APPROVALS
More informationSUBSTATION EQUIPMENT - Page 1 of 8
BATTERY BANKS 1. GENERAL: JEA utilizes a 125 volt DC system for the control and operation of its transmission and distribution substations. JEA has standardized on lead acid type battery banks to supply
More informationNCPP. Nickel Cadmium Pocket Plate Batteries. Block Cell Dimensional and Electrical Data
NCPP Nickel Cadmium Pocket Plate Batteries Block Cell Dimensional and Electrical Data Nickel Cadmium Pocket Plate Batteries HBL's Nickel Cadmium Pocket Plate Battery designs are based on the superior Pocket
More information34-SDMS-01 SPECIFICATIONS FOR
SPECIFICATIONS FOR M V DROPOUT FUSE CUT OUTS This specification is property of SEC and subject to change or modification without any notice CONTENTS C l a u s e s: Page No. 1- SCOPE 3 2- CROSS REFERENCES
More informationDakshin Gujarat Vij Company Limited
Dakshin Gujarat Vij Company Limited CIN U40102GJ2003SGCO42909 Regd. & Corporate Office: Urja Sadan, Nana Varachha Road, Kapodara Char Rasta,Surat 395 006 C & R DEPARTMENT Phone No.: 0261 2506100-200-175
More informationA Brief Look at Batteries
A Brief Look at Batteries At some point during 501/502 you will need to use one or more batteries in order to provide power to a system that needs to be deployed away from line power. It s a good idea
More informationCONTROLLIX CORPORATION CONTROLLIX.COM LOW VOLTAGE AUTOMATIC SWITCH CAPACITOR BANK SPECIFICATIONS
LOW VOLTAGE AUTOMATIC SWITCH CAPACITOR BANK SPECIFICATIONS I. SCOPE a. This specification describes the necessary requirements for the design, fabrication, and operation of automatically switched, low
More informationStandards are finally approved by the Standards High Council of Iranian Ministry of Petroleum.
FOREWORD This Standard is intended to be used within and for Iranian Ministry of Petroleum (N.I.O.C, N.I.G.C, N.P.C., N.I.O.R.D.C. and other affiliate organizations and companies) and has been prepared
More informationSD / SDH. Applicable Standards. Applications and Key Benefits. FIAMM Manufacturing. - Technical Features
Applications and Key Benefits 2V cells - 80Ah to 2320Ah nominal capacity Ideal for: - Power generation and distribution - Electrical Utilities /Switchgear - UPS & datacenter systems - Railway crossing,
More informationRELIABILITY Power Systems Ni-Cd Batteries Div. DS Ver.3.11/ Jan 2011 Page 1/20
RELIABILITY Power Systems Ni-Cd Batteries Div. DS Ver.3.11/ Jan 2011 Page 1/20 RELIABILITY NICKEL CADMIUM BATTERIES Owing to the structural materials they use, RELIABILITY Nickel Cadmium (Ni-Cd) Batteries
More information1.0 Scope. 2.0 Codes and Standards
Table of Contents 1.0 Scope... 2 2.0 Codes and Standards... 2 3.0 Site Conditions... 3 4.0 General Requirements... 3 5.0 Technical Requirements... 5 6.0 Protection, Alarm, Control, Indication and Metering
More information56-SDMS-07 REV. 01 SPECIFICATIONS FOR
56-SDMS-07 REV. 01 SPECIFICATIONS FOR UNIT SUBSTATIONS UP TO 36 kv ALUMINUM TRANSFORMER ALUMINUM BUS BARS LVDP This specification is property of SEC and subject to change or modification without any notice
More informationSpecification Approval Sheet
Specification Approval Sheet Name: Ni-Cd rechargeable battery Model: 20305 SPEC: SC 2200mAh Approved By Checkup Make Signature Date Customer Confirmation Company Name: Stamp:, U.S.A. www.tenergybattery.com
More informationStandby Products SD-SDH. series. Technical Features. Applications. Product Features
SD-SDH series The FIAMM s SD-SDH battery range can be used in standby mode for duties requiring high performance and reliability. The SD-SDH family is specially designed for discharge rates that are required
More informationBharat Heavy Electricals Limited (High Pressure Boiler Plant) Tiruchirappalli , TAMIL NADU. INDIA CAPITAL EQUIPMENT/ MATERIALS MANAGEMENT
An ISO 9001 Company ENQUIRY Bharat Heavy Electricals Limited (High Pressure Boiler Plant) Tiruchirappalli 620014, TAMIL NADU. INDIA CAPITAL EQUIPMENT/ MATERIALS MANAGEMENT NOTICE INVITING TENDER Phone:
More informationFeatures and Benefits
C&D Tubular GEL (OPzV) Series For Standby & Cyclic Applications C&D Tubular GEL (OPzV) Series range of valve regulated lead acid stationary batteries combine the benefits of recombination technology (i.e.
More informationشركة كهرباء محافظة القدس المساهمة المحدودة
Our Ref: Date: Messrs. Dear Sir, Tender 22/2017 (re-bidding) 11& 33Kv Fuse Cutouts and Links You are kindly requested to bid for supply and delivery (DDP) for the medium voltage overhead line accessories
More informationMANUAL 4. The Norms set for discharge of its Function
MANUAL 4 The Norms set for discharge of its Function i. For the achievement of Organizational Objectives, each department has formulated its own norms based on various standards like Engineering, Accounting
More informationSwitchgear Utility specific gravity nominal sulfuric acid. 10 years, full float service at 77 F (25 C)
12-373 UL Recognized Component RETURN LEAD RECYCLE LIBERTY SERIES 1000 VALVE REGULATED LEAD-CALCIUM BATTERY FOR STANDBY APPLICATIONS Capacities from 100 to 600 Ampere-hours (8 hours to 1.75 VPC) 343 to
More informationTECHNICAL SPECIFICATIONS OF 2 KVA POWER CONDITIONING UNIT
TECHNICAL SPECIFICATIONS OF 2 KVA POWER CONDITIONING UNIT 1.0 PURPOSE: 1. To charge the battery bank through Solar PV source and AC supply. 2. To invert and produce utility quality sine wave. 3. Inverters
More informationNi-Cd Battery Product Specification
Ni-Cd Battery Product Specification SC1600 1. This specification governs the performance of the following Nickel-Cadmium Cylindrical cell and its stackup battery. SC BATTERY 16NC50 (To include all 1.6Ah
More informationSTANDARDIZATION ORGANIZATION FOR G.C.C (GSO) GSO 34/2007
STANDARDIZATION ORGANIZATION FOR G.C.C (GSO) GSO 34/2007 LEAD-ACID STARTER BATTERIES USED FOR MOTOR VEHICLES AND INTERNAL COMBUSTION ENGINES ICS: 43.040.00 LEAD-ACID STARTER BATTERIES USED FOR MOTOR VEHICLES
More informationTECHNICAL SPECIFICATION FOR 11 KV AIR BREAK (A.B.) SWITCHES:
TECHNICAL SPECIFICATION FOR 11 KV AIR BREAK (A.B.) SWITCHES: 1. SCOPE : This specification covers design, manufacturing, testing at manufacturer s works, inspection, packing & delivery of 11 KV Air Break
More informationGASTON GTF range battery manual
GASTON GTF range battery manual Type 1. Brief introduction GTF stationary lead-acid battery (acid spray-proof type), ranging from 200ah to 3000ah at 10hr rate in 17 models, are mainly applied in power
More informationBHARAT HEAVY ELECTRICALS LIMITED Industrial Valves Plant Goindwal (AMRITSAR) Enquiry Date:
BHARAT HEAVY ELECTRICALS LIMITED Industrial Valves Plant Goindwal 143422 (AMRITSAR) ENQUIRY Phone:+91 1859 223381 (+91 1859 222002, 222036, 222039 Extn 117) Fax :+91 1859 222 061 Email :srk@ivp.bhel.co.in
More informationProduct Guide. An Invensys company
Product Guide An Invensys company Contents Page I/ The principle of the gas-recombination battery... 2 II/ Charge characteristics... 4 III/ Electrical performance tables... 5 IV/ Battery calculations Float
More informationInviting Tenders for Supply, Installation, Testing and Commissioning of 500 KVA DG Set for Temperature Controlled Warehouse at Medchal, Hyderabad.
Inviting Tenders for Supply, Installation, Testing and Commissioning of 500 KVA DG Set for Temperature Controlled Warehouse at Medchal, Hyderabad. Amendment to Tender Reference No. BL/LI/CC/HYD/22 Date
More informationTECHNICAL SPECIFICATION FOR 11 KV CAPACITOR BANK
TECHNICAL SPECIFICATION FOR 11 KV CAPACITOR BANK MAHARASHTRA STATE ELECTRICITY DISTRIBUTION COMPANY LTD. PAGE 1 OF 7 TECHNICAL SPECIFICATION FOR 11 KV.CAPACITOR BANK 1.0 SCOPE: This specification covers
More informationPure Lead-Tin Technology
Pure Lead-Tin Technology Pure Lead-Tin technology offers many advantages which include: High overall efficiency High energy density Excellent high rate performance Excellent low temperature performance
More informationFLOAT CHARGER (40A) & BOOST CHARGER (35A) FOR NO BREAK POWER SUPPLY SYSTEM WITH REQUIREMENT FOR SCADA
GUJARAT ENERGY TRANSMISSION CORPORATION LTD. SARADAR PATEL VIDYUT BHAVAN, RACE COURSE, BARODA 390 007. TECHNICAL SPECIFICATIONS FOR FLOAT CHARGER (40A) & BOOST CHARGER (35A) FOR GETCO/E/TS-50V BCHR(SCADA)
More informationHigh Temperature Rechargeable Nickel-Metal Hydride Cylindrical Battery Pack, 3 cell, 4000mAh
Datasheet ENGLISH High Temperature Rechargeable Nickel-Metal Hydride Cylindrical Battery Pack, 3 cell, 4000mAh SPECIFICATIONS: RS Article: 917-5920 HT18670x3 Nominal Voltage 3.6V Typical 4000 mah/0.2 CmA
More informationXHP. Low maintenance high performance batteries
Low maintenance high performance batteries Range Low maintenance, high performance Ni-Cd batteries Powerful assurance for critical applications Depend upon where vital UPS, engine starting and emergency
More information34-SDMS-02 SPECIFICATIONS FOR
SPECIFICATIONS FOR M V & L V FUSE LINKS This specification is property of SEC and subject to change or modification without any notice TABLE OF CONTENTS 1.0 SCOPE 3 2.0 CROSS REFERENCES 3 3.0 APPLICABLE
More informationSealed Rechargeable Nickel Cadmium N800AA/BTNP
1. SCOPE The specifications governs the performance of the following Nickel-Cadmium Cylindrical cell and its battery pack.. Model: NCAA800 Cell Size: AA ( :14.1 ±0.2 mm H: 48.0 ±0.5 mm) 2. DATA OF BATTERY
More informationPRODUCT SPECIFICATION. Rechargeable Nickel Metal Hydride Battery Model: GP210AAHC(CS)
PRODUCT SPECIFICATION Rechargeable Nickel Metal Hydride Battery Model: GP210AAHC(CS) Revision History Revision Date Initiator Reason for Change 00 03/08/2006 YX Zhu New issue. Prepared By YX Zhu Approved
More informationNPS/003/002 Technical Specification for 30V Distribution Tripping Battery and Charger Systems
Version:- 2.1 Date of Issue:- July 2016 Page 1 of 29 NPS/003/002 Technical Specification for 30V Distribution Tripping Battery and Charger Systems 1. Purpose This document is to detail the technical requirements
More informationPURE LEAD PLUS UPS APPLICATIONS. Valve Regulated Lead Acid Battery Designed for UPS Standby Power Applications Watts per Cell
UPS 12-1121 PURE LEAD PLUS Valve Regulated Lead Acid Battery Designed for UPS Standby Power Applications 305-545 Watts per APPLICATIONS Data Centers Network Operations Centers Industrial Process Control
More informationModel No:L521F Page 1 of 7. Alkaline Manganese Button Cell L521F
Model No:L521F Page 1 of 7 1 Scope The specification is applicable to the Vinnic brand (Mercury free) supplied by BATTERY WORKS LTD. 2 Kind of Products Specified Name (Designation): L521F IEC Designation:
More informationTechnical Specification for Pole Mounted Capacitor Rack
Technical Specification for Pole Mounted Rack Page 1 1. Scope and Function a) Pole mounted capacitor racks shall be installed on a distribution feed as an economical means of applying capacitor units to
More informationSPECIFICATIONS SEALED NICKEL CADMIUM RECHARGEABLE BATTERY N1700SC-HTP
1. SCOPE The specifications governs the performance of the following Nickel-Cadmium Cylindrical cell and its battery pack.. Model: N17SC-HTP Cell Size: SC ( :22.1 ±.2 mm H: 42. ±.5 mm) 2. DATA OF BATTERY
More informationENGLISH. RS Stock No
RS Stock No 777-0399 RS Article : 7770399 AA x 20 Nominal Voltage 24V Capacity Typical 1300 mah/0.2 CmA Minimum 1200 mah/0.2 CmA Charge Standard 0.1 CmA for 16 hrs. Rapid 1CmA for 1.2hrs.(approx.) (With-
More informationSPECIFICATIONS FOR MOTOR OPERATED VALVES
Doc No: 254625-300-SP-INT-004 Rev: B Page 1 of 11 SPECIFICATIONS FOR MOTOR OPERATED VALVES Hindustan Petroleum Corporation Ltd Visakha Dispatch Station VR-ATP Area, Naval Base Post Visakhapatnam - 530
More informationBharat Heavy Electricals Limited (High Pressure Boiler Plant) Tiruchirappalli , TAMIL NADU, INDIA CAPITAL EQUIPMENT / MATERIALS MANAGEMENT
An ISO 9001 Company Bharat Heavy Electricals Limited (High Pressure Boiler Plant) Tiruchirappalli 620014, TAMIL NADU, INDIA CAPITAL EQUIPMENT / MATERIALS MANAGEMENT ENQUIRY NOTICE INVITING TENDER Phone:
More informationUnit AE01K Knowledge of Locating and Correcting Simple Electrical Faults in the Automotive Workplace
Assessment Requirements Unit AE01K Knowledge of Locating and Correcting Simple Electrical Faults in the Automotive Workplace Content: Basic electrical principles a. Explain the direction of current flow
More informationFLOAT CHARGER & BOOST CHARGER F O R NO BREAK POWER SUPPLY SYSTEM (Float 100A & Boost 60 A with SCADA application)
GUJARAT ENERGY TRANSMISSION CORPORATION LTD. SARADAR PATEL VIDYUT BHAVAN, RACE COURSE, BARODA 390 007. TECHNICAL SPECIFICATIONS FOR FLOAT CHARGER (100A) & BOOST CHARGER (60A) FOR WITH REQUIREMENT FOR SCADA
More informationEVO SERIES BATTERY CHARGER SERIES BATTERY CHARGER
EVO SERIES BATTERY CHARGER SERIES BATTERY CHARGER Evo Series battery charger designed with YOU in mind. Evo Series battery charger is a next generation SCR-based utility battery charger. This evolutionary
More informationD.C. DISTRIBUTION BOARD
PRAMBL: The TC is maintaining 50-volt battery backup system for the PLCC communication. The 50-volt D.C. supply from the Float cum Boost charger is brought to D.C. Distribution Board from where supply
More informationPOWER FOR TOMORROW. Motive Power. Network Power. Chargers. Bloc Batteries. Accessories. Service
POWER FOR TOMORROW TODAY The Eternity Technologies range is built using only the highest quality and most efficient production processes at our state-of-the-art manufacturing centre in the UAE. It is this
More information2 Volt AGM Range. Haze Battery Company Ltd
2 Volt AGM Range Haze Battery Company Ltd Q Q M M The Haze HZB - AGM range covers Ah capacities from 50Ah to 3850Ah (C10) with dimensions suitable for racking systems for maximum space utilisation. Specially
More informationENGLISH. RS Stock number Description:
RS Stock number 199-747 Description: Tagged to allow for combining into larger battery packs for permanent installation Voltage 1.2V Quick 4 to 6hr charging rate. This is a sealed Nickel-Metal Hydride
More informationTECHNICAL SPECIFICATION FOR SHACKLE HARDWARE FITTINGS SUITABLE FOR TENSION STRING TO BE USED FOR 11KV LINE
TECHNICAL SPECIFICATION FOR SHACKLE HARDWARE FITTINGS SUITABLE FOR TENSION STRING TO BE USED FOR 11KV LINE The hardware fittings suitable for tension string to be used for 11KV consisting of following
More informationINTER PLANT STANDARD STEEL INDUSTRY NO CORRESPONDING IS
INTER PLANT STANDARD STEEL INDUSTRY SOFT STARTER FOR VOLTAGE UP TO 690 V AC IPSS: 1-10-040-15 IPSS NO CORRESPONDING IS 0. FOREWORD 0.1 This interplant standard has been prepared by the Standard Committee
More informationSECTION 1 SCOPE, SPECIFIC TECHNICAL REQUIREMENT AND QUANTITIES
Tamil Nadu Transmission Corporation Limited Bharat Heavy Electricals Limited 400/110 KV Substation at Thappagundu & 400/230-110 KV Substation at Anikadavu, Technical specification for 420/245/132kV Isolators
More informationRS Stock No
RS Stock No. 770-0371 EN RS Article : 7770371 AA x 10 Nominal Voltage 12.0V Capacity Typical 1300 mah/0.2 CmA Minimum 1200 mah/0.2 CmA Charge Standard 0.1 CmA for 16 hrs. Rapid 1C for 1.2hrs.(approx.)
More informationGuangzhou Vkan Certification and Testing Institute (CVC former GTIHEA)
CNAS L0095 age 1 of 14 ages No.: GJW2009-0893 TEST REORT NAME OF SAMLE: Valve Regulated Lead Acid Battery CLIENT: Shenzhen Center ower Tech. Co., Ltd. CLASSIFICATION OF TEST: Commission Test Guangzhou
More informationModel No:L1154F Page 1 of 7. Alkaline Manganese Button Cell L1154F
Model No:L1154F Page 1 of 7 1 Scope The specification is applicable to the Vinnic brand (Mercury free) supplied by BATTERY WORKS LTD. 2 Kind of Products Specified Name (Designation): L1154F IEC Designation:
More informationSupply of 63 kva DIESEL GENERATOR SET WITH AMF
No. NIQ/INKEL/2015-16/162 24 TH Nov 2015 NOTICE INVITING QUOTATION Sealed Quotations are invited for and on behalf of INKEL Limited, having its registered office at INKEL Centre, Off Vallathol junction,
More informationFEATURES & benefits. Constant Power Discharge Ratings - Watts per 77 F (25 F) Operating Time (in minutes) to 1.
-1029 Valve Regulated Lead Acid Battery Designed for UPS Standby Power Applications. APPLICATIONS Data Centers Network Operations Centers Industrial Process Control Facilities Internet Housing Sites Semiconductor
More informationEcoSafe EOPzV. Operation Guide for Solar Applications
EcoSafe EOPzV Operation Guide for Solar Applications 2 Ecosafe EOPzV Specific Abilities The specific abilities of this type of battery for renewable energy applications are as follows: Cycling (one cycle
More information026-2 : 1996 CEB STANDARD
026-2 : 1996 CEB STANDARD COMPRESSION CONNECTORS & TERMINATIONS FOR OVERHEAD LINE CONDUCTORS CEYLON ELECTRICITY BOARD SRI LANKA CONTENTS 1. Scope 2 2. System Parameters 2 3. Service Conditions 2 4. Applicable
More informationSPECIFICATION FOR HARDWARE FITTINGS SUITABLE FOR TENSION STRING TO BE USED FOR 11KV/22KV LINE
SPECIFICATION FOR HARDWARE FITTINGS SUITABLE FOR TENSION STRING TO BE USED FOR 11KV/22KV LINE The hardware fittings suitable for tension string to be used for 11KV / 22 KV consisting of following components.
More informationMotive Power. Network Power. Chargers. Bloc Batteries. Accessories. Service
The Eternity Technologies range is built using only the highest quality and most efficient production processes at our state-of-the-art manufacturing centre in the UAE. It is this innovation, modern design
More informationTECHNICAL SPECIFICATION FOR 11 KV AUTOMATIC CAPACITOR SWITCH
TECHNICAL SPECIFICATION FOR 11 KV AUTOMATIC CAPACITOR SWITCH MAHARASHTRA STATE ELECTRICITY DISTRIBUTION COMPANY LTD. PAGE 1 OF 7 TECHNICAL SPECIFICATION FOR 11 KV AUTOMATIC CAPACITOR SWITCH 1.0 SCOPE:
More informationTECHNICAL SPECIFICATIONS FOR LT DISTRIBUTION BOX MADE FROM THERMOSETTING PLASTIC HAVING 200 /400 AMP CAPACITY.
TECHNICAL SPECIFICATIONS FOR LT DISTRIBUTION BOX MADE FROM THERMOSETTING PLASTIC HAVING 200 /400 AMP CAPACITY. 1.0 SCOPE: This specification covers the design, manufacturing and testing of LT Distribution
More informationSpecification Approval Sheet
Specification Approval Sheet Name: Alkaline Dry Battery Model: 40308 SPEC: 6LR61 Approved By Checkup Make Signature Date Customer Confirmation Company Name: Stamp:, U.S.A. Tel: 510.687.0388 Fax: 510.687-0328
More informationPURE LEAD PLUS UPS APPLICATIONS Valve Regulated Lead Acid Battery Designed for UPS Standby Power Applications Watts per Cell
-11 PURE LEAD PLUS Valve Regulated Lead Acid Battery Designed for UPS Standby Power Applications 305-545 Watts per Cell FEATURES & benefits APPLICATIONS Data Centers Network Operations Centers Industrial
More informationTYPE TEST REPORT. OPzS CELLS AND BLOCK BATTERIES. According to IEC
TYPE TEST REPORT OPzS CELLS AND BLOCK BATTERIES According to IEC 60896-11 Systems Sunlight SA, 2 Ermou & Nikis Str, Syntagma Square 105 63 Athens, Attica, Greece Report Type Type Test acc. to IEC 60896-11,
More informationPOWERPLUS NICKEL CADMIUM BATTERIES SINTERED PLATE / POCKET PLATE 5AH to 1000AH / 20+ years long life
NICKEL CADMIUM RANGE CATALOGUE POWERPLUS NICKEL CADMIUM BATTERIES SINTERED PLATE / POCKET PLATE 5AH to 1000AH / 20+ years long life Nickel Cadmium cells using sintered plate / pocket plate technology have
More informationMotive Power. Network Power. Chargers. Bloc Batteries. Accessories. Service
The Eternity Technologies range is built using only the highest quality and most efficient production processes at our state-of-the-art manufacturing centre in the UAE. It is this innovation, modern design
More informationLIBERTY SERIES 1000 VALVE REGULATED LEAD-CALCIUM BATTERY For standby applications Capacities from 25 to 600 Ampere-hours
RETURN RECYCLE 12-373 LEAD LIBERTY SERIES 1000 VALVE REGULATED LEAD-CALCIUM BATTERY For standby applications Capacities from 25 to 600 Ampere-hours UL Recognized Component C&D Technologies Powercom Division
More informationSPECIFICATIONS OF SINGLE GIRDER UNDER SLUNG E.O.T. CRANE CAPACITY: 5 MT
1 SPECIFICATIONS OF SINGLE GIRDER UNDER SLUNG E.O.T. CRANE CAPACITY: 5 MT QUALIFICATION CRITERIA Vendor has to compulsorily meet the following requirements to get qualified for consideration of the technical
More informationNICKEL-CADMIUM POCKET TYPE ALKALINE STORAGE BATTERY
MANUAL OF OPERATION AND MAINTENANCE FOR NICKEL-CADMIUM POCKET TYPE ALKALINE STORAGE BATTERY 1/18 CONTENTS 1. Applications. (3) 2. Main properties of the cell and the battery.... (3) 3. Main performance
More informationMAHARASHTRA NATURAL GAS LIMITED
Replies to Queries of the Bidders Date: 15.09.2018 SUB: Replies to queries of the bidders against Tender for Procurement of Natural Gas RPD & Turbine Meters with EVC for CGD Network of MNGL, Pune REF:
More information