Electronic Shifter. Lee Redstone V Lewis Weston V Jason Deglint V Group #5. Supervisor Ashoka K. S. Bhat. Due Oct.
|
|
- Neal Chase
- 5 years ago
- Views:
Transcription
1 Electronic Shifter Lee Redstone V Lewis Weston V Jason Deglint V Group #5 Supervisor Ashoka K. S. Bhat Due Oct. 16, 2012 Dept. Electrical and Computer Engineering University of Victoria All rights reserved. This report may not be reproduced in whole or in part, by photocopy or other means, without the permission of the author.
2 Electronic Shifter 1 Table of Contents Background... 2 Motivation... 2 Proposed Project... 2 Possible Solutions... 3 Linear Actuator... 3 Steering Wheel connection... 3 Microcontroller... 3 Work Plan... 4 Milestones... 5 Deliverables... 6 Force Measurements... 6 Acquisition and testing of a linear actuator... 6 Website... 6
3 Electronic Shifter 2 Background The UVic FSAE team competes annually in the Formula SAE competition series hosted by the Society of Automotive Engineers. The nature of the competition involves designing, fabrication, and running a new open wheeled race car each year. The majority of the components on the vehicle are built by the team for the specific purpose of the competition. The driver controls are a major design consideration each year, and the team is hoping to increase their competitiveness by making the vehicle easier to drive. It is vital that reliability is not sacrificed for this project, weight reductions can be made through iterative designs, but the device is required to operate at 100% in a very extreme environment. Motivation The Formula SAE car is built to compete in high speed autocross course specifically designed for the small cars built by the teams. Speeds easily reach 80-90km/hr and the driver must constantly move between 1st, 2nd, and 3rd gears while on the course. The current mechanical design requires the driver to remove their left hand from the steering wheel to engage the shifting lever. The time required to shift gears is on the order of magnitude of seconds. With the incorporation of an electronically actuated shifting mechanism the switching functionality can be moved onto the steering wheel through the use of paddles or push-buttons. This will allow the driver to keep both hands on the wheel, and has the potential to lower the shifting time to the order of 10 s of milliseconds. Proposed Project The following report outlines the proposed project for Group 5, of the Fall 2012 class of ELEC 399. The group intends to design and construct a fully electric shifting mechanism specifically designed for the UVic Formula SAE team. The team is investigating the feasibility of replacing the current mechanical shifting mechanism with an electric actuator. The device must be capable of shifting gears on the transmission of a 2003 Honda CBR F4i engine. To limit the scope of this project the clutch actuation will be reserved for a separate project. The design considerations for this project are: 1. Reliability- Shifting gears is a critical operation while the vehicle is being driven. The device must be capable of shifting thousands of times before weakening. 2. Weight- The implemented system must be as light as possible. The entire car is constrained to be as light as possible, and the mechanical system is currently very light weight. 3. Cost- The system must have a reasonable base price. There exists store bought solutions with very high price points. The team currently cannot afford these products.
4 Electronic Shifter 3 Possible Solutions In order to design and construct a fully electric shifting mechanism specifically designed for the UVic Formula SAE team different aspects of the project must be considered. 1. Linear Actuator 2. Steering Wheel Connection 3. Microcontroller Linear Actuator There are two different types of electric linear actuators which can be used to shift the transmission: 1. Electric Motor 2. Solenoid A comparison of the major advantages and disadvantages are discussed in the following chart: DC Motor Solenoid Advantages Much cheaper than solenoid. Minimal moving parts. Disadvantages Requires additional moving parts such as gears which can cause additional losses. Very expensive relative to a DC motor. Both options plan to be researched and tested to see which better suits the projects needs. Steering Wheel connection In addition, during driver egress, the steering wheel will be removed quickly and potentially thrown. For this reason, all electric connections from the buttons on the steering wheel to the main control system will need to be very robust. The initial idea to solve this problem is the use a TRS (Tip, Ring, Sleeve) connector which will allow the steering wheel to rotate freely while driving as well as have the capability of being removed. Either a 35 mm or ¼ Jack could be used for this. Microcontroller Currently we are planning to use the F28069 Piccolo controlstick from Texas Instruments. It uses a microcontroller mounted on a USB-accessible breakout board. Some reasons for choosing this platform include: Ease of programming through USB Dedicated PWM outputs (if required for motor control) Pre-written code for motor/solenoid control. These features will save time and complexity, allowing us to focus on developing a more effective solution on the electromechanical side of the project.
5 Electronic Shifter 4 Work Plan The Work Plan can be summarized by the following steps: 1. Determine specifications and requirements for the project - What kind of mechanism is best suited for the actuator solenoid or motor? - What are the torque/force requirements to shift the transmission? - What are the speed/timing requirements to shift the transmission? - Will the actuator require its own power source? - Where and how will the shift buttons be mounted? - What gauge of wire is required and how will it be connected? If the buttons are on the steering wheel, how can we ensure that the wheel is still removable? - Do the shift buttons need debouncing? If so, how? - How can we determine what gear the transmission is in, and how can we easily shift into neutral? 2. Design a solution based around answering the above questions 3. Physical implementation of the design 4. Testing the implementation by comparing it to the design specifications 5. Adjust the specifications and design/implementation as dictated by test results Below is a rough timeline for each stage of the project, mid-september: 1. Determining specifications and requirements - Two weeks, specifications first draft complete by first week of October 2. Designing a solution - Four weeks, ready for production by first week of November 3. Implementation - Two weeks, ready for testing by mid-november 4. Testing and adjustments - Two weeks, project is at a stage where it can undergo real-world use Obviously, each stage of the project will overlap considerably with others, as design, implementation, and testing may be done simultaneously, and specification and respecification will occur constantly throughout the project. However, the timeline above serves as a guide to keep the team on schedule, and to remind them of the short period of time available to complete the project. At the same time as this, there is an informational aspect of this project which involves keeping logbooks to track organize our ideas, preparing reports for describe our progress, and developing a website to showcase our results. Due to its nature, the informational portion of this project will be ongoing throughout the semester.
6 Electronic Shifter 5 Milestones The project can be divided into three major sections, which have their own milestones 1. Electromechanical systems connected to the transmission - Determine what kind of mechanism is best suited for the actuator - Find the torque/force requirements to shift the transmission - Find the speed/timing requirements to shift the transmission - Determine if actuator will require its own power source 2. Electronic and software systems for controlling the electromechanical system - Find how best to mount the three shift buttons (up, down, neutral) - Determine the best method for connecting the steering wheel wiring to the microcontroller - Ensure that the shift buttons are debounced in the microcontroller or in hardware - Figure out how the microcontroller will know which gear the transmission is in 3. Informational showcasing - Develop, publish, and maintain a website
7 Electronic Shifter 6 Deliverables The Deliverables so far in this project are as follows: 1. Force Measurements 2. Acquisition and testing of a linear actuator 3. Website Force Measurements The Force needed to move the shifter out the transmission was measured. Both Shifting Up and Shifting Forces were measured. From To Shifting Down Force (kilos) From To Shifting Up Force (kilos) As seen, the maximum force measured was 11 kilos. Since we need a force that will always guarantee to shift the transmission 150% of 11 kilos will be used. Therefore, 16.5 kilos will be used when deciding on a linear actuator. Acquisition and testing of a linear actuator Based on the force measurements above, an automotive power lock actuator was purchased and tested. It was capable of applying 4-5 kgf. This indicates that it is a third to a quarter of the required force for the project. Possible solutions involve using a force-multiplying lever or gearset, a more powerful motor in the actuator, or using several actuators in parallel. Website The website has been created in order to share any news updates and documentation with the public. The URL of the website is
FSAE Electronic Shifter Final Project Report
FSAE Electronic Shifter Final Project Report by Lee Redstone lredston@uvic.ca Lewis Weston ldweston@uvic.ca Jason Deglint jdeglint@uvic.ca http://electronicshifter.wordpress.com/ Supervisor: Dr. Ashoka
More informationExhaust Gas Temperature Monitor For An Internal Combustion Engine
ExhaustGasTemperatureMonitorForAnInternal CombustionEngine INTERIMREPORT By: JamesBoileau V00738149 SawyerPahl V00731863 LudiLing V00737324 GarvinRuus V00688254 KurtisNewman V00241647 SubmittedonOctober16,2012
More informationUniversity of New Hampshire: FSAE ECE Progress Report
University of New Hampshire: FSAE ECE Progress Report Team Members: Christopher P. Loo & Joshua L. Moran Faculty Advisor: Francis C. Hludik, Jr., M.S. Courses Involved: ECE 541, ECE 543, ECE 562, ECE 633,
More informationRIT Formula SAE Senior Design
RIT Formula SAE Senior Design Agenda Project Description Work Breakdown Customer Needs Customer Specifications Current/Previous System Design Proposed Design #1 Proposed Design #2 Testing Plans Concept
More informationFormula SAE Paddle Shift System
Formula SAE Paddle Shift System Senior Design II Report Group 5 Group Members Richard Pittman Musab Hmeidan Sean Feschak Kevin Castillo Fall 2015 i TABLE OF CONTENTS 1.0 Executive Summary 1 2.0 Project
More informationTest Plans & Test Results
P10227 Variable Intake System for FSAE Race Car Test Plans & Test Results By: Dave Donohue, Dan Swank, Matt Smith, Kursten O'Neill, Tom Giuffre Table of contents 1. MSD I: WKS 8-10 PRELIMINARY TEST PLAN...
More informationPROJECT IDEA SUBMISSION
PROJECT IDEA SUBMISSION Team Contacts - 1 st person listed serves as the point of contact with Professor Nelson - Initial team size may be from 1 to 6 members (all members must agree to have their name
More informationDesign and Manufacturing of Pneumatic Gear Shifter for Go-Kart
Design and Manufacturing of Pneumatic Gear Shifter for Go-Kart Tanmay J Wadgaonkar Madhur R Pawar Swapnil V Vaidya Abstract Design and fabrication of a semi automatic gear shifting mechanism for a Go Kart
More informationSAE Baja - Drivetrain
SAE Baja - Drivetrain By Ricardo Inzunza, Brandon Janca, Ryan Worden Team 11A Concept Generation and Selection Document Submitted towards partial fulfillment of the requirements for Mechanical Engineering
More informationVehicle Systems Engineering and Integration Activities - Phase 3
Vehicle Systems Engineering and Integration Activities - Phase 3 Interim Technical Report SERC-2011-TR-015-3 December 31, 2011 Principal Investigator: Dr. Walter Bryzik, DeVlieg Chairman and Professor
More informationDraft Agenda. Item Subject Responsible Time. 4. GAS INFORMATION SERVICES PROJECT IMO 10 min. 5. OPTIONS FOR GAS BULLETIN BOARD SYSTEM IMO 15 min
Gas Advisory Board Draft Agenda Meeting No. 1 Location: Parmelia Hilton, Swan B Room 14 Mill Street, Perth WA 6000 Date: 20 December 2011 Time: 11:15am 12:15pm Item Subject Responsible Time 1. WELCOME
More informationME 455 Lecture Ideas, Fall 2010
ME 455 Lecture Ideas, Fall 2010 COURSE INTRODUCTION Course goal, design a vehicle (SAE Baja and Formula) Half lecture half project work Group and individual work, integrated Design - optimal solution subject
More informationCenterwide System Level Procedure
5.ARC.0004.2 1 of 10 REVISION HISTORY REV Description of Change Author Effective Date 0 Initial Release J. Hanratty 7/17/98 1 Clarifications based on 7/98 DNV Audit and 6/98 Internal Audit (see DCR 98-029).
More informationASME Human Powered Vehicle
ASME Human Powered Vehicle By Yousef Alanzi, Evan Bunce, Cody Chenoweth, Haley Flenner, Brent Ives, and Connor Newcomer Team 14 Problem Definition and Project Plan Document Submitted towards partial fulfillment
More informationAC : HYBRID MINI-BAJA CAR PROJECT
AC 2007-1591: HYBRID MINI-BAJA CAR PROJECT Michael Rudisill, Northern Michigan University Jesse Racine, Northern Michigan University Tim Nelson, Northern Michigan University Michael Truscott, Northern
More informationUTA Formula SAE Racecar Combustion and Electric
UTA Formula SAE Racecar Combustion and Electric Dr. Bob Woods Professor of Mechanical Engineering Distinguished Teaching Professor Director, Arnold E. Petsche Center for Automotive Engineering Faculty
More informationImplementation of a Grid Connected Solar Inverter with Maximum Power Point Tracking
ECE 4600 GROUP DESIGN PROJECT PROGRESS REPORT GROUP 03 Implementation of a Grid Connected Solar Inverter with Maximum Power Point Tracking Authors Radeon Shamilov Kresta Zumel Valeria Pevtsov Reza Fazel-Darbandi
More informationVandal Hybrid Racing Sponsorship Packet University of Idaho.
University of Idaho 1 Vandal Hybrid Racing The Vandal Hybrid Racing Team is a non-profit organization which advances the education of future engineers by designing and building a vehicle to compete in
More informationTaiwan Bicycle Industry Standard
TBIS 4210 5:2016 Taiwan Bicycle Industry Standard TBIS 4210-5 First edition 2016.01.01 Cycles Safety requirements for bicycles Part 5: Steering test methods Reference number: TBIS 4210-5:2015 (FDTS) TBIS
More informationTHE ELECTRIC AUTOMOTIVE MOTOR CONTROL SYSTEM
THE ELECTRIC AUTOMOTIVE MOTOR CONTROL SYSTEM Timothy E. Jackson Project Proposal October 30, 2003 ETec 471, Morton Western Washington University Department of Engineering Technology. INTRODUCTION In today
More informationVehicle Systems Engineering and Integration Activities - Phase 4
Vehicle Systems Engineering and Integration Activities - Phase 4 Interim Technical Report SERC-2012-TR-015-4 March 31, 2012 Principal Investigator: Dr. Walter Bryzik, DeVlieg Chairman and Professor Mechanical
More informationSAE Mini Baja Drivetrain
SAE Mini Baja Drivetrain By: Abdulrahman Almuflih, Andrew Perryman, Caizhi Ming, Zan Zhu, Ruoheng Pan Team 02 Mid-point review REPORT Submitted towards partial fulfillment of the requirements for Mechanical
More informationSAE Mini BAJA: Suspension and Steering
SAE Mini BAJA: Suspension and Steering By Zane Cross, Kyle Egan, Nick Garry, Trevor Hochhaus Team 11 Project Progress Submitted towards partial fulfillment of the requirements for Mechanical Engineering
More informationM:2:I Milestone 2 Final Installation and Ground Test
Iowa State University AerE 294X/AerE 494X Make to Innovate M:2:I Milestone 2 Final Installation and Ground Test Author(s): Angie Burke Christopher McGrory Mitchell Skatter Kathryn Spierings Ryan Story
More informationMIPRover: A Two-Wheeled Dynamically Balancing Mobile Inverted Pendulum Robot
ECE 3992 Senior Project Proposal MIPRover: A Two-Wheeled Dynamically Balancing Mobile Inverted Pendulum Robot 6 May 2005 Prepared By: Kevin E. Waters Department of Electrical and Computer Engineering University
More informationNewsletter November This month CFS10. Engine. Body. Welcome CFS10 p.1 CFS10 West p.4 What now? p.5 Interested? p.5
Newsletter November 2010 CFS10 This year s team includes 25 members of different nationalities and with different educational backgrounds. The team consists of six different subgroups, responsible for
More informationEngineering Diploma Resource Guide ST280 ETP Hydraulics (Engineering)
Engineering Diploma Resource Guide ST80 ETP Hydraulics (Engineering) Introduction Hydraulic systems are a fundamental aspect of engineering. Utilised across a variety of sectors including aviation, construction,
More informationLinear Induction Motor (LIMO) Modular Test Bed for Various Applications
Linear Induction Motor (LIMO) Modular Test Bed for Various Applications ECE 4901 Senior Design I Fall 2013 Fall Project Report Team 190 Members: David Hackney Jonathan Rarey Julio Yela Faculty Advisor
More informationGasket Simulations process considering design parameters
Gasket Simulations process considering design parameters Sonu Paroche Deputy Manager VE Commercial Vehicles Ltd. 102, Industrial Area No. 1 Pithampur, District Dhar MP - 454775, India sparoche@vecv.in
More informationSenior Project Ideas
2006 2007 Senior Project Ideas Prof. Raghu Agarwal (ragarwal@sjsu.edu) 924-3845 Title Team Skills Needed Funding 1 Human Powered Vehicle 4-6 Hands-on Self 2 SAE Formula 1 Car 4-6 Hands-on Self 3 Minibaja
More informationTest Plans & Test Results
P09310 Automatic Shift Controls for ATV Test Plans & Test Results By: Ashley Shoum, Matt Dombovy-Johnson, Keith Cobb, Jon Willistein, Feng Li, Bibhu Shah, Sarah Bicho Table of contents MSD I: WKS 8-10
More informationThe Wildcat Formula Racing 2017 Sponsor Information Packet
The Wildcat Formula Racing 2017 Sponsor Information Packet A Letter from the Team Captain Thank you for your interest in Formula SAE at the University of Arizona, also known as Wildcat Formula Racing.
More information2010 Sponsorship Information Package
2010 Sponsorship Information Package 1 Contents Introduction 3 What is Formula SAE 4 Formula SAE Concept 5 Competition Regulations 6 University of Kentucky in FSAE 7 Sponsorship Benefits 8 Sponsorship
More informationProposed Solution to Mitigate Concerns Regarding AC Power Flow under Convergence Bidding. September 25, 2009
Proposed Solution to Mitigate Concerns Regarding AC Power Flow under Convergence Bidding September 25, 2009 Proposed Solution to Mitigate Concerns Regarding AC Power Flow under Convergence Bidding Background
More informationWritten Exam Public Transport + Answers
Faculty of Engineering Technology Written Exam Public Transport + Written Exam Public Transport (195421200-1A) Teacher van Zuilekom Course code 195421200 Date and time 7-11-2011, 8:45-12:15 Location OH116
More informationStatus of the Informal Working Group on ACSF
Submitted by the Chair of the IWG on ACSF Informal document GRVA-02-35 2 nd GRVA session, 28. Jan 01. Feb. 2019, Agenda item 5(d) Status of the Informal Working Group on ACSF Summary of ACSF IWG Meetings
More informationDevelopment of Low Cost Electronic Gear Shifting System with Clutch Operation for Sequential Gearbox
Development of Low Cost Electronic Gear Shifting System with Clutch Operation for Sequential Gearbox Dhruv Tanwar B.Tech (Automotive Design Engineering), dhrutnawar4@gm ail.com Abhishek Sharma B. Tech
More informationSAE Baja - Drivetrain
SAE Baja - Drivetrain By Ricardo Inzunza, Brandon Janca, Ryan Worden Team 11 Engineering Analysis Document Submitted towards partial fulfillment of the requirements for Mechanical Engineering Design I
More informationDevelopment of Seamless Shift for Formula One Car
Development of Seamless Shift for Formula One Car Takashi YOSHIOKA* Katsumi KUBO* Takeshi UCHIYAMA* Ryo MATSUI* ABSTRACT Honda focused on gearbox development during its third Formula One era. The reduction
More informationRotorcraft Gearbox Foundation Design by a Network of Optimizations
13th AIAA/ISSMO Multidisciplinary Analysis Optimization Conference 13-15 September 2010, Fort Worth, Texas AIAA 2010-9310 Rotorcraft Gearbox Foundation Design by a Network of Optimizations Geng Zhang 1
More informationSolar Powered Golf Cart
Solar Powered Golf Cart Group 9 Jake Bettis Jacob Krueger Matt Roland Matt Tourtelot Project Description The main objective of this project is to design and build a solar-powered, energy efficient electric
More informationSAE Mini Baja West. By Ahmed Alnattar, Neil Gehr, and Matthew Legg Team 11. Concept Generation Document
SAE Mini Baja West By Ahmed Alnattar, Neil Gehr, and Matthew Legg Team 11 Concept Generation Document Submitted towards partial fulfillment of the requirements for Mechanical Engineering Design I Fall
More informationGreen Line LRT: Beltline Segment Update April 19, 2017
Green Line LRT: Beltline Segment Update April 19, 2017 Quick Facts On April 11, 2017, City Council approved Administration s recommendation for the Green Line to be underground in the Beltline from 2 Street
More information2015 Project Plan Report
2015 Project Plan Report Jack Haiston, jhaiston@outlook.com, (970) 420-0943 Tyler Norris, tnorris93@me.com, (513) 288-0258 Loren Christensen, lchristensen92@gmail.com, (719) 580-0750 Nathan Houser, nthnhsr@rams.colostate.edu,
More informationSolar Power-Optimized Cart
Solar Power-Optimized Cart Initial Project and Group Identification Document Due: September 17, 2013 Group #28 Group Members: Jacob Bitterman Cameron Boozarjomehri William Ellett Potential Sponsors: Duke
More informationNew Frontier in Energy, Engineering, Environment & Science (NFEEES-2018 ) Feb
RESEARCH ARTICLE OPEN ACCESS DESIGN AND IMPACT ANALYSIS OF A ROLLCAGE FOR FORMULA HYBRID VEHICLE Aayush Bohra 1, Ajay Sharma 2 1(Mechanical department, Arya College of Engineering & I.T.,kukas, Jaipur)
More informationSAE Mini BAJA: Suspension and Steering
SAE Mini BAJA: Suspension and Steering By Zane Cross, Kyle Egan, Nick Garry, Trevor Hochhaus Team 11 Problem Formulation and Project Plan Report Submitted towards partial fulfillment of the requirements
More informationLate Starter. Tuesday, November 6, 2018
Late Starter Tuesday, Please note the following item(s) was not included with your agenda as this item(s) was received after the agenda package was printed. Planning and Works Committee Report TES-RTS-18-09,
More informationAD45 Front Strut Handling Tool George Fisher Mine, Mount Isa Mines, a Glencore Company
AD45 Front Strut Handling Tool George Fisher Mine, Mount Isa Mines, a Glencore Company The Problem Removal and replacement of the front suspension struts on Caterpillar AD45 underground haulage ejector
More informationKISSsys Application 008: Gearbox Concept Analysis
KISSsoft AG Frauwis 1 CH - 8634 Hombrechtikon Telefon: +41 55 264 20 30 Calculation Software for Machine Design Fax: +41 55 264 20 33 www.kisssoft.ch info@kisssoft.ch 1. Abstract KISSsys: Efficient Drivetrain
More informationImplementation of telecontrol of solar home system based on Arduino via smartphone
IOP Conference Series: Materials Science and Engineering PAPER OPEN ACCESS Implementation of telecontrol of solar home system based on Arduino via smartphone To cite this article: B Herdiana and I F Sanjaya
More informationThird Quarter 2017 Performance and Business Update. October 26, 2017
Third Quarter 2017 Performance and Business Update October 26, 2017 1 Important Notice Please read this management presentation together with the Company s press release issued earlier today announcing
More informationMerger of the generator interconnection processes of Valley Electric and the ISO;
California Independent System Operator Corporation Memorandum To: ISO Board of Governors From: Karen Edson Vice President, Policy & Client Services Date: August 18, 2011 Re: Decision on Valley Electric
More informationHDV CO2 emission certification 1 st meeting of the Editing board
HDV CO2 emission certification 1 st meeting of the Editing board DG Growth Maciej Szymański 2.03.2015 Internal market, Industry, Entrepreneurship and SMEs Meeting agenda Work of the Editing board: Objectives
More informationDesign and Hardware Implementation of a Supervisory Controller for a Wind Power Turbine
ECE 4600 Group Design Project Proposal Group 09 Design and Hardware Implementation of a Supervisory Controller for a Wind Power Turbine Supervisors Annakkage, Udaya D., P.Eng McNeill, Dean, P.Eng Bagen
More informationDecommissioning & Re-use in NL: A Joint Effort
Oil & Gas Industry Forecast 2017 Decommissioning & Re-use in NL: A Joint Effort 28 March 2017 Agenda About EBN & NOGEPA Dutch decommissioning challenge NL Masterplan Joint Industry Project H1 2017 Summary
More informationAaren Healy, 20 September 2017 / 1
Network Rail s consultation on variable charges and station charges in CP6 Electricity charge for traction (EC4T) and the electrification asset usage charge (EAUC) Aaren Healy, 20 September 2017 / 1 Purpose
More informationDYNAMIC EFFICIENCY - Propulsors with Contra-Rotating Propellers for Dynamic Positioning
Author s Name Name of the Paper Session DYNAMIC POSITIONING CONFERENCE October 14-15, 2014 THRUSTER SESSION DYNAMIC EFFICIENCY - Propulsors with Contra-Rotating Propellers for Dynamic Positioning By Kari
More informationECE 480 Design Team 3: Designing Low Voltage, Low Current Battery Chargers
Michigan State University Electrical Engineering Department ECE 480 Design Team 3: Designing Low Voltage, Low Current Battery Chargers Application Note Created by: James McCormick 11/8/2015 Abstract: The
More informationProject Narrative Description
0 Project Narrative Description Charge Spot is intended to demonstrate the feasibility of an autonomous electric vehicle charging system for residential use. The goal of Charge Spot is to have no user
More informationWeek 11. Module 5: EE100 Course Project Making your first robot
Week 11 Module 5: EE100 Course Project Making your first robot Dr. Ing. Ahmad Kamal Nasir Office Hours: Room 9-245A Tuesday (1000-1100) Wednesday (1500-1600) Course Project: Wall-Follower Robot Week 1
More informationMARKFORGED CASE STUDY STANLEY INFRASTRUCTURE
MARKFORGED CASE STUDY Stanley Black & Decker, an S&P 500 company, is a diversified global provider of hand tools, power tools and related accessories, electronic security solutions, healthcare solutions,
More informationDESIGN AND EXPERIMENTATION OF TEST RIG TO CHARACTERIZE HYDROSTATIC DRIVEFOR LINEAR ACTUATOR
DESIGN AND EXPERIMENTATION OF TEST RIG TO CHARACTERIZE HYDROSTATIC DRIVEFOR LINEAR ACTUATOR Sherif Elbaz 1, Moatasem 2, Ibrahim 3, Nabila 4, Mohamed 5 1 Automotive Engineering Department, Ain-Shames University,
More informationConsumer Goods Manufacturers Operational Profile 1.1 Please state what your main activity(ies) is/are within manufacturing End-product manufacturer Ma
Particulars About Your Organisation Organisation Name Eisbär Eis GmbH Corporate Website Address http://www.eisbaer-eis.de Primary Activity or Product Manufacturer Related Company(ies) Membership Membership
More informationAmbient PM 10 Monitoring Sechelt, B.C Update
Ministry of Environment LOWER MAINLAND REGION Ambient PM 10 Monitoring Sechelt, B.C. 2004-2005 Update E N V I R O N M E N T A L Q U A L I T Y Library and Archives Canada Cataloguing in Publication Data
More informationFor a while now I have been
TECHNICAL TRAINING Shift Pointers Author: Subject: Erratic 2-3 shift, code P0780 Unit: BAYA 5-speed automatic Vehicle Applications: 2003 Honda LX Essential Reading: Rebuilder Shop Owner Center Manager
More informationOptimization of the Intake System for the 2008 Formula SAE Race Car
Optimization of the Intake System for the 2008 Formula SAE Race Car Nilufar Damji A thesis submitted in partial fulfillment of the requirements for the degree of BACHELOR OF APPLIED SCIENCE Supervisor:
More informationSystem Integration of an Electronic Monitoring System in All-Terrain Vehicles
System Integration of an Electronic Monitoring System in All-Terrain Vehicles Waylin Wing Central Michigan University, Mount Pleasant, MI 48858 Email: wing1wj@cmich.edu An electronic monitoring system
More informationSAE Mini BAJA: Suspension and Steering
SAE Mini BAJA: Suspension and Steering By Zane Cross, Kyle Egan, Nick Garry, Trevor Hochhaus Team 11 Progress Report Submitted towards partial fulfillment of the requirements for Mechanical Engineering
More informationSolar Panel Cubic Charger OMG Studio. ENSC 440/305 Project SFU Engineering Science
Solar Panel Cubic Charger OMG Studio ENSC 440/305 Project SFU Engineering Science Dec 14, 2011 CEO Michael Chen Majors in Electronics Engineering Third Year Group Leader Directions Programming CFO Shuyang
More informationWELLMAN LAKE CABIN UPDATE Mar 2019
WELLMAN LAKE CABIN UPDATE Mar 2019 How We Got Here. Cabin was built by MFFA in the 1970 s Over time some remedial work was done through volunteer effort. In the early 2000 s additional work was identified
More informationABB life cycle services Uninterruptible power supplies
ABB life cycle services Uninterruptible power supplies 2 ABB Life cycle brochure UPS service portfolio Life cycle services for uninterruptible power supplies As your service partner, ABB guarantees you
More informationUSING INSPIRE AS AN UPFRONT DESIGN, OPTIMIZATION & SIMULATION TOOL FOR EXISITNG MANUAL GEARBOX COMPONENTS
USING INSPIRE AS AN UPFRONT DESIGN, OPTIMIZATION & SIMULATION TOOL FOR EXISITNG MANUAL GEARBOX COMPONENTS Lokesh Kumar Gupta Manager Drive Line Eicher Polaris Plot- SP1 & 2, Kukas Jaipur India 302028 Lkgupta@eicherpolaris.in
More informationNew Ulm Public Utilities. Interconnection Process and Requirements For Qualifying Facilities (0-40 kw) New Ulm Public Utilities
New Ulm Public Utilities Interconnection Process and Requirements For Qualifying Facilities (0-40 kw) New Ulm Public Utilities INDEX Document Review and History... 2 Definitions... 3 Overview... 3 Application
More informationDevelopment of a Multibody Systems Model for Investigation of the Effects of Hybrid Electric Vehicle Powertrains on Vehicle Dynamics.
Development of a Multibody Systems Model for Investigation of the Effects of Hybrid Electric Vehicle Powertrains on Vehicle Dynamics. http://dx.doi.org/10.3991/ijoe.v11i6.5033 Matthew Bastin* and R Peter
More informationThird Quarter 2018 Performance and Business Update. October 24, 2018
Third Quarter 2018 Performance and Business Update October 24, 2018 1 Important Notice Please read this management presentation together with the Company s press release issued earlier today announcing
More informationSUBJECT: Russell Hill Subway Train Accident Of August 11, 1995 Due Diligence Checklist Update
MEETING DATE: August 31, 2005 SUBJECT: Russell Hill Subway Train Accident Of August 11, 1995 Due Diligence Checklist Update RECOMMENDATION It is recommended that the Commission: i) Receive for information
More informationModel 407SE Swivel Drawbar Eye
MANUFACTURING CO. THE FIRST NAME IN QUALITY COUPLINGS Installation, Inspection, Operation & Maintenance Guide Model 407SE Swivel Drawbar Eye IMPORTANT Read these instructions completely before installing,
More informationCost Benefit Analysis of Faster Transmission System Protection Systems
Cost Benefit Analysis of Faster Transmission System Protection Systems Presented at the 71st Annual Conference for Protective Engineers Brian Ehsani, Black & Veatch Jason Hulme, Black & Veatch Abstract
More informationGrandee Biotechnologies Sdn Bhd
Particulars About Your Organisation Organisation Name Corporate Website Address Primary Activity or Product Processor and/or Trader Related Company(ies) Membership Membership Number Membership Category
More informationFormula. Sponsorship proposal Team Formula NUST
Formula Sponsorship proposal Team Formula NUST 2 Pakistan Navy Engineering College (PNEC), the Karachi campus of National University of Sciences & Technology (NUST) Islamabad, is proud to announce the
More informationFAF & Private Company Issues
NASBA FAF & Private Company Issues Terri Polley, President & CEO Financial Accounting Foundation Anchorage, Alaska June 29, 2012 1 The Definition of an Accountant Someone who solves a problem you did not
More informationGC108: EU Code: Emergency & Restoration: Black start testing requirement
Stage 01: Modification Proposal Grid Code GC108: EU Code: Emergency & Restoration: Black start testing requirement Purpose of Modification: This modification seeks to align the GB Grid Code with the European
More informationFORMULA SAE ENGINE INTERNALS GROUP. Emerson Hawkins, Whitney Hurlbut, Kirk Fraser, Saad Mohamed and Greg Fitzpatrick
FORMULA SAE ENGINE INTERNALS GROUP Emerson Hawkins, Whitney Hurlbut, Kirk Fraser, Saad Mohamed and Greg Fitzpatrick PRESENTATION OVERVIEW Plan FSAE Engine Internals Group Fall Presentation 2 PRESENTATION
More informationDiscovery Center Gesture Control Robotics Exhibit Product Requirements
Discovery Center Gesture Control Robotics Exhibit Product Requirements U of I Discovery Austyn Sullivan-Watson Angelo Stratigakes Zhihui Wang Chaeun Kim 1 Document History Rev Number Date Modified By Reason
More informationSimulating Rotary Draw Bending and Tube Hydroforming
Abstract: Simulating Rotary Draw Bending and Tube Hydroforming Dilip K Mahanty, Narendran M. Balan Engineering Services Group, Tata Consultancy Services Tube hydroforming is currently an active area of
More informationAlaska Research CubeSat 1 Separation Switch Sub-Assembly Failure Analysis
Alaska Research CubeSat 1 Separation Switch Sub-Assembly Failure Analysis Matt Pacheco Author/Engineer Signature of Approval Date Denise Thorsen Director Signature of Approval Date Alaska Space Grant Program
More informationSouthern California Edison Rule 21 Storage Charging Interconnection Load Process Guide. Version 1.1
Southern California Edison Rule 21 Storage Charging Interconnection Load Process Guide Version 1.1 October 21, 2016 1 Table of Contents: A. Application Processing Pages 3-4 B. Operational Modes Associated
More informationCS/EE/ME 75 FSAE Electric 12 October 2015
CS/EE/ME 75 FSAE Electric 12 October 2015 Guillaume Blanquart Azita Emami Richard Murray Joseph Bowkett Cibele Halasz Noah Olsman Shenghan Yao Engineering and Applied Science California Institute of Technology
More informationModel-Based Design and Hardware-in-the-Loop Simulation for Clean Vehicles Bo Chen, Ph.D.
Model-Based Design and Hardware-in-the-Loop Simulation for Clean Vehicles Bo Chen, Ph.D. Dave House Associate Professor of Mechanical Engineering and Electrical Engineering Department of Mechanical Engineering
More informationUTAS Motorsport. Formula SAE Australasia Sponsorship Proposal
UTAS Motorsport Formula SAE Australasia 2017 Sponsorship Proposal What is Formula SAE? Formula SAE is an internationally renowned student engineering design competition. Run by the Society of Automotive
More informationUSING LEAN TO ENGAGE AND ALIGN THE ENTIRE ORGANIZATION. Didier Rabino, VP Lean Sensei Julie Garrison, HR System Director November 9, 2015
USING LEAN TO ENGAGE AND ALIGN THE ENTIRE ORGANIZATION Didier Rabino, VP Lean Sensei Julie Garrison, HR System Director November 9, 2015 ABOUT THE PRESENTERS Julie GARRISON HR System Director 1999 2006:
More informationStationary Bike Generator System
Central Washington University ScholarWorks@CWU All Undergraduate Projects Undergraduate Student Projects Spring 2017 Stationary Bike Generator System Rakan Alghamdi Central Washington University, rk_rk11@hotmail.com
More informationEEL Project Design Report: Automated Rev Matcher. January 28 th, 2008
Brad Atherton, masscles@ufl.edu, 352.262.7006 Monique Mennis, moniki@ufl.edu, 305.215.2330 EEL 4914 Project Design Report: Automated Rev Matcher January 28 th, 2008 Project Abstract Our device will minimize
More informationIPRO 326: Design and Simulation of a Hybrid-Electric Vehicle
IPRO 326: Design and Simulation of a Hybrid-Electric Vehicle Outline IPRO Team Structure HEV vs. Traditional ICE Basic Principles of how an HEV works Technical Branch HEV Team Conclusions IPRO 326: Design
More informationSynthesis of Cal Poly Senior Projects Relating to Public Transportation in San Luis Obispo County
Synthesis of Cal Poly Senior Projects Relating to Public Transportation in San Luis Obispo County In partial fulfillment of CE 424 Professor Eugene Jud By David Thornhill November 14, 2007 Purpose The
More informationWashington Metropolitan Area Transit Authority Board Action/Information Summary
Washington Metropolitan Area Transit Authority Board Action/Information Summary Action Information MEAD Number: Resolution: Yes No TITLE: LRT and Streetcar Interoperability Study PURPOSE: To brief the
More informationUnigraphics NX 6 Tips and Recommended EcoCAR CAD Procedures
Page : 1 of 25 University of Victoria EcoCAR Team Unigraphics NX 6 Tips and Recommended EcoCAR CAD Procedures Daniel Prescott August 3, 2009 Page : 2 of 25 TABLE OF CONTENTS TABLE OF CONTENTS... 2 PREAMBLE...
More informationSponsorship Brochure
2012 2013 Sponsorship Brochure Dear Prospective Sponsor, 2 Introduction In this short brochure we will introduce you to the Tufts Hybrid Racing Team and show you how we can work together to achieve success.
More informationGC108: EU Code: Emergency & Restoration: Black start testing requirement
Stage 01: Modification Proposal Grid Code GC108: EU Code: Emergency & Restoration: Black start testing requirement Purpose of Modification: This modification seeks to align the GB Grid Code with the European
More information