Operating Instructions BlueCamreddot 5 Users

Transcription

1 Operating Instructions BlueCamreddot 5 Users

2 BlueCamreddot Operating Instructions Table of contents Page 1 eneral instructions 3 2 Opening with the administrator code 4 3 Changing the administrator code 4 4 Locking by the administrator/user 5 5 Programming/changing the user code 5 6 Opening with the user code 6 7 Opening after 4 wrong code entries 6 8 Deleting the user code 7 9 Opening with the master code 7 10 Changing the master code 7 11 Power supply and battery change 8 Legend LED flashes green LED is permanently green LED flashes red LED is permanently red Tone signal Carl Wittkopp mbh - errors and omissions excepted Operating Instructions No

3 Operating Instructions BlueCamreddot 1 eneral instructions Please read the operating instructions carefully, before activating the lock. The lock is supplied with the following factory codes: - Administrator factory code: Master factory code: User factory code: None of the 5 possible user codes is set. For your security, change the factory codes immediately. Change codes only if the safe is opened and lock is in closed position. In case of changing an administrator/master code, the lock has to be opened with the corresponding administrator/master code before. Do not use any personal data like birthdays or telephone numbers as new codes. If the lock is not opened or closed within 3 seconds after the ON-button is pressed, the electronics will shut down. Press the ON-button again and repeat the operation. If the time has been exceeded for entering a new code, the electronics will shut down. The old code remains valid. Every correct code entry at opening or closing is confirmed by a tone signal and a green LED will flash. These signals are not described in the following instructions. Do not use force. Do not open the lock case. Otherwise you endanger the function of the lock and you lose any warranty claims. Operating Instructions No

4 BlueCamreddot Operating Instructions 2 Opening with the administrator code The administrator code is only necessary if the lock is locked and the user code is not known. 1. Press the ON-button. 2. Press 0 and enter a 4-digit administrator code. 10 seconds 3 Changing the administrator code 1. Press the ON-button. 2. Press 0 and enter a 4-digit administrator code. 10 seconds 4. Press 0 again until the LED shines permanently green and enter the new 4-digit administrator code. 5. The new administrator code is accepted. If the time has been exceeded for entering the new code in step 4, the electronics will shut down. The old code remains valid Operating Instructions No

5 Operating Instructions BlueCamreddot 4 Locking by the administrator/user The locking process is the same for both users. 1. Press the ON-button. 2. Wait until the LED shines permanently green. 3 seconds 3. Turn the handle within 3 seconds. The lock is locked. 4. After locking always check if the door is blocked. 5 Programming/changing the user code Up to 5 different user codes can be programmed or changed. 1. Press the ON-button. 2. Press 0 and enter a 4-digit administrator code. 10 seconds 4. While the green LED flashes, press one of the numbers 1, 2, 3, 4 or 5 and enter the new 4-digit user code. 5. The new user code is accepted. If the time has been exceeded for entering the new code in step 4, the electronics will shut down. The old code remains valid. Operating Instructions No

6 BlueCamreddot Operating Instructions 6 Opening with the user code For opening, first press your user number (1, 2, 3, 4 or 5) and then the previously selected 4-digit user code. 1. Press the ON-button. 2. Press one of the numbers 1, 2, 3, 4 or 5 within 10 seconds and enter the new 4-digit user code. 3 seconds If a wrong user code has been entered, a tone signal sounds several times and the LED flashes red. Press the ON-button after the LED has lapsed and enter your code again. 7 Opening after 4 wrong code entries After 4 wrong code entries the lock is blocked for 30 seconds. During this time it is not possible to enter a code. At the end of the blocked time, the red LED goes out and a tone signal sounds several times. 3. Press the ON-button. 4. Enter your 4-digit user code within 10 seconds. 3 seconds 5. Turn the handle within 3 seconds. The lock is opened. If a wrong code has been entered in step 4, the lock is blocked for another 30 seconds Operating Instructions No

7 Operating Instructions BlueCamreddot 8 Deleting the user code During deleting a user code the lock has to be closed. 1. Press the ON-button. 2. Press 0 and enter the 4-digit administrator code. 10 seconds 3. Press one of the numbers 1, 2, 3, 4 or 5 for the user and wait until the lock shuts down. 10 seconds 4. The user code is deleted. 9 Opening with the master code The master code is only necessary if the lock is locked and the user code or administator code is not known. 1. Keep the ON-button pressed until the LED shines permanently green. 2. Press 7 and enter the 6-digit master code. 10 seconds 10 Changing the master code 1. Keep the ON-button pressed until the LED shines permanently green. 2. Press 7 and enter the 6-digit master code. 10 seconds 4. Enter the new 6-digit master code within 5 seconds. 5. The new master code is accepted. Operating Instructions No

8 BlueCamreddot Operating Instructions 9 Power supply and battery change The lock is operated with a 9 volt alkaline battery. We recommend using a battery with reduced heavy metal concentration. If the LED flashes red after pressing the ON-button, the battery voltage is low. Change the battery as soon as possible. If the LED flashes red five times and a triple tone signal sounds after pressing the ON-button, the code cannot be entered because of low voltage. After the first code number has been entered, the LED goes out. Change the battery immediately. To change the battery, the M4 screw and the M18 nut at the back of the lock has to be loosened. Lift the battery cover at the lock case and change the battery. eplace the battery cover again and fasten nut and screw. If the battery is so low that a code entry is not possible anymore, the lock can be supplied with power from outside. Place a 9 volt block battery at the power terminals of the input unit (see Fig. 1) and open the lock as described in point 3. Always dispose used batteries in an environmentally friendly way. Trade Collecting points or public waste management authorities take back waste batteries free of charge. Place battery for emergency power supply here Fig. 1: Emergency power supply Operating Instructions No