We give a no quibble 3 year parts warranty and our service is on a personal basis.

Transcription

1 BH REPAIRS. LTD 236, SHERWOOD STREET WARSOP MANSFIELD NOTTS. NG20 0HJ TEL; MOBILE; ; If you need any more information please contact me. We have many (1600+ to date ) happy customers throughout the UK and Europe. We may have a customer near you, who you may be able to contact and ask their opinion and even demonstrate the lift for you. Please contact me for these details. You would need to contact me with your postcode for a carriage quote. We no longer accept payments by, debit or credit cards as we feel that the banks and card companies are not prepared to accept responsibility in the event of fraud. We have been the victims of card fraud. We know it s easier by card, but so is fraud! We can accept a BACS transfer, direct bank transfer, ( Just like paying a bill online or even at the bank ), or you can make payment by cheque. Or cash if you want to collect and test before you buy! You can send a cheque to the above address made out to BH Repairs LTD with your full postal details where to send the lift and who to make the invoice out to. We give a no quibble 3 year parts warranty and our service is on a personal basis. Lifts are delivered on a tail lift lorry and unloaded with a pallet/pump truck. Hoping to hear from you, Kind regards, Bill Company registration No

2 BH REPAIRS. LTD 236, Sherwood Street, Warsop, Mansfield. Notts. NG 20 0HJ TEL; MOBILE; , Web site, GARAGE EQUIPMENT SPECIALIST VEHICLE LIFT ENGINEER 2.7 TON MOBILE LIFT 3 year parts warranty MOBILE LIFT SALES SEE VIDEO LINK ON WEBSITE Introducing a superb mobile mid rise lift. A 2.67 ton. capacity (6000 Ib ) portable scissor lift. It operates on 240 Volts single phase supply. 13 amp plug fitted. ( A 16amp type C or D type Motor rated circuit breaker is required, or 30 amp as fitted in most kitchens ) Dual hydraulic rams. Solid safety lock bar. (with several safety lock positions) The large foot print of the lift creates a steady platform for the raised vehicle. NISSON NAVARA Many different types of vehicles can be accommodated. 2 CV vw

3 Page 2 September 26, 2018 The power unit can be located in a 360 degree position around the lift for maximum efficiency. This cart is also used as a wheeled dolly to move the mid rise lift on a smooth concrete surface. The lift can be rolled easily to a different location if needed. The lift arms on top of the H section platform, can be swivelled and slide back and forwards in the slots shown to give flexibility.

4 Page 3 September 26, 2018 THE 5 PAD HEIGHT MEASUREMENTS ARE APPROX AND TAKEN FROM THE TOP OF THE PLATFORM mm mm mm mm mm. These 2 with Extensions as shown THE OVERAL LIFT DIMENSIONS ARE APPROX inches 66 inches 50 inches 66 inches when raised 88 inches when lowered WHEN THE LIFT IS AT ITS LOWEST POSITION IT HAS A CLEARANCE OF 5 inches IN THE MIDDLE OF THE LIFT. IT IS ADVISABLE TO USE A PLANK EITHER SIDE TO RUN UP ON

5 Page 4 September 26, 2018 WITH LOW GROUND CLEARANCE CARS. FITTING THE CASTORS TO FRONT (RAM) END OF LIFT TO IMPROVE MANOUVERABILITY. IT IS NOT ADVISABLE TO RAISE OR LOWER A CAR WITH CASTORS ON!! The fitting of these castors is your option and are easy to remove when not required. Care has to be taken when moving the lift this way, as the hose and safety cable are still connected and can pull the trolley over and damage the power pack, or trap the hose. The castors are easy to fit, and only need bolting corner to corner. We have used two, 8mm bolts,just finger tightened. You could also place the trolley with the motor on the top of the lift, (on a board to avoid damage to power pack.?!) and pull the lift with a rope It is possible to raise the lift 6 to 12 inches, to give a little more ground clearance, without making too much difference to the angle of working castor. The heavy duty, rubber wheel castors will take a load of 150kg per castor. IT IS NOT ADVISABLE TO RAISE OR LOWER A CAR WITH CASTORS ON!! Company registration No

6 Page 5 September 26, 2018 DISTANCES FROM CENTRE OF PADS ( 3 SHEETS ) MEASUREMENTS TO PAD CENTRES SHEET ONE 34 INCHES TOP FRAME 66 INCHES LONG 60 INCHES 25 inches WIDTH 40 INCHES WHEN THE LIFT IS AT ITS LOWEST POSITION IT HAS A CLEARANCE OF 5 inches IN THE MIDDLE OF THE LIFT. IT IS ADVISABLE TO USE A PLANK EITHER SIDE TO RUN UP ON WITH LOW GROUND CLEARANCE CARS.

7 Page 6 September 26, 2018 SHEET TWO ARMS EXTENDED MEASUREMENTS TO PAD CENTRES 34 INCHES 76 INCHES

8 Page 7 September 26, 2018 SHEET THREE ARMS EXTENDED AND SWUNG OUT ( TO APPROX JACKING POINTS ) MEASUREMENTS TO PAD CENTRES 52 INCHES 68 INCHES