SOUTH AFRICAN NATIONAL STANDARD
|
|
|
- Hubert Washington
- 5 years ago
- Views:
Transcription
1 ISBN SANS 1239:2004 Any reference to SABS 1239 is deemed to be a reference to this standard (Government Notice No of 8 November 2002) SOUTH AFRICAN NATIONAL STANDARD Plugs, socket-outlets and couplers for industrial purposes WARNING Front-end standard. Can only be read in conjunction with SANS and SANS Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001 Tel: Fax: SABS
2 SANS 1239:2004 Table of changes Change No. Date Scope Amdt Amended to update a reference standard, to delete annex A and to change the foreword accordingly. Amdt Amended to add requirements for plugs, socket-outlets and couplers with pin and contact tube contacts. Foreword This South African standard was approved by National Committee SABS/TC 067/SC 03, Electricity distribution systems and components Electrical accessories, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This edition cancels and replaces the edition 2.1 (SABS 1239:2001). A vertical line in the margin shows where the text has been changed by amendment No. 2. This document is referenced in the Local Government: Municipal Systems Act, 2000 (Act No. 32 of 2000). Annex B forms an integral part of this standard. Annex C is for information only. Amdt 1 This standard is a "front-end" specification that can only be read in conjunction with SANS and SANS Users of this standard should ensure that they also have copies of the most recent editions of these standards. Compliance with this document cannot confer immunity from legal obligations. Reaffirmed and reprinted in February This document will be reviewed every five years and be reaffirmed, amended, revised or withdrawn.
3 Contents Page Foreword 1 Scope Normative references Definitions Requirements... 4 Annex A Deleted by amendment No Annex B (normative)... 5 Annex C (informative)
4 This page is intentionally left blank 2
5 Plugs, socket-outlets and couplers for industrial purposes 1 Scope 1.1 This standard specifies requirements for plugs, socket-outlets, cable couplers and appliance couplers, intended for use in industry (either indoors or outdoors), in agriculture, and on board ship, with single-phase and three-phase supplies, at a d.c. operating voltage or an a.c. r.m.s. operating voltage not exceeding 690 V, a frequency not exceeding 500 Hz and a rated current not exceeding 250 A. The accessories are intended for continuous use at an ambient temperature that does not normally exceed 40 C. 1.2 This standard also covers appliance sockets (inlets) incorporated in, or fixed to, electrical appliances or electrical equipment and accessories for use in extra-low-voltage industrial installations. 1.3 This standard does not cover accessories for applications that involve explosion hazards or in which flameproof equipment is required. NOTE Where the ambient temperature is likely to exceed 40 C, accessories might have to be de-rated so that the maximum permissible temperature of 85 C is not exceeded. 2 Normative references This part of SANS 1239 contains provisions, which, through reference in this text, constitute provisions of this part of SANS All standards are subject to revision and, since any reference to a standard is deemed to be a reference to the latest edition of that standard, parties to agreements based on this standard are encouraged to take steps to ensure the use of the most recent editions of the standards indicated below. Information on currently valid national and international standards can be obtained from the SABS Standard Division. SANS /IEC , Plugs, socket-outlets and couplers for industrial purposes Part 1: General requirements. SANS /IEC , Plugs, socket-outlets and couplers for industrial purposes Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories. 3 Definition For the purposes of this standard, the definitions given in SANS and the following definition apply: accessory: A general term used for a plug, a socket-outlet, a cable coupler, an appliance coupler, or other similar items. 3
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-32159-8 Any reference to SABS 1551-1 is deemed to be a reference to this standard (Government Notice No. 1373 of 8 November 2002) SOUTH AFRICAN NATIONAL STANDARD Check valves (flanged and
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-21023-6 Any reference to SABS 0241 is deemed to be a reference to this standard (Government Notice No. 1373 of 8 November 2002) SOUTH AFRICAN NATIONAL STANDARD Tachograph centres Installation
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-32599-2 SOUTH AFRICAN NATIONAL STANDARD Electrical security installations Part 3: Electric fences (non-lethal) and manufacture requirements WARNING This document references other documents
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-32948-8 SOUTH AFRICAN NATIONAL STANDARD Petroleum jelly (petrolatum) WARNING This document references other documents normatively. Published by SABS Standards Division 1 Dr Lategan Road
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-28761-0 SOUTH AFRICAN NATIONAL STANDARD Earthing of low-voltage (LV) distribution systems Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-31203-9 SOUTH AFRICAN NATIONAL STANDARD Traffic lights WARNING This document references other documents normatively. Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-33225-9 SOUTH AFRICAN NATIONAL STANDARD Automotive fuels Requirements and test methods for diesel WARNING This document references other documents normatively. Published by SABS Standards
SOUTH AFRICAN NATIONAL STANDARD. Plug and socket-outlet systems for household and similar purposes for use in South Africa
ISBN 978-0-626-27016-2 SANS 164-1:2012 SOUTH AFRICAN NATIONAL STANDARD Plug and socket-outlet systems for household and similar purposes for use in South Africa Part 1: Conventional system, 16 A 250 V
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-29010-8 SOUTH AFRICAN NATIONAL STANDARD Homologation of motor vehicle models Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001 Tel: +27 12
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-31488-0 SOUTH AFRICAN NATIONAL STANDARD Switchgear Metal-enclosed ring main units for rated a.c. voltages above 1 kv and up to and including 36 kv WARNING This document references other
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-34898-4 SOUTH AFRICAN NATIONAL STANDARD Motor vehicle tyres and rims Dimensions and loads Part 1: General WARNING This document references other documents normatively. Published by the South
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-29808-1 SOUTH AFRICAN NATIONAL STANDARD Kerosene for domestic heating and illuminating WARNING This standard references other documents normatively. Published by SABS Standards Division
SOUTH AFRICAN NATIONAL STANDARD
ICS 43020 ISBN 0-626-17429-5 Edition 11 Any reference to SABS 0319 is deemed to be a reference to this standard (Government Notice No 1373 of 8 November 2002) SOUTH AFRICAN NATIONAL STANDARD The registration
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-2-3382-8 Edition 3.2 and IEC corr. 1 IEC 0309-1:2012 Edition.2 and corr. 1 SOUTH AFRICAN NATIONAL STANDARD Plugs, socket-outlets and couplers for industrial purposes This national standard is
SOUTH AFRICAN NATIONAL STANDARD
ISBN 0-626-17643-3 SOUTH AFRICAN NATIONAL STANDARD Safety rules for the construction and installation of lifts Part 3: Lifts for persons with Amdt 3 disabilities (stairlifting platforms) Published by Standards
SOUTH AFRICAN NATIONAL STANDARD
ICS 4304040 ISBN 0-626-17644-1 Any reference to SABS SV 1051-1 is deemed to be a reference to this standard (Government Notice No 1373 of 8 November 2002) SOUTH AFRICAN NATIONAL STANDARD Motor vehicle
SOUTH AFRICAN NATIONAL STANDARD
ICS 23.020.10; 75.200 ISBN 0-626-15187-2 SOUTH AFRICAN NATIONAL STANDARD Above-ground storage tanks for petroleum products Published by Standards South Africa 1 dr lategan road groenkloof! private bag
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-23806-3 SOUTH AFRICAN NATIONAL STANDARD The handling, storage, distribution and maintenance of liquefied petroleum gas in domestic, commercial and industrial installations Part 4: The transportation
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-19459-8 SOUTH AFRICAN NATIONAL STANDARD Verification standards for the verification of volume-measuring instruments, including commercial standards of volume Published by Standards South
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-22612-1 SANS 20013-H:2009 Edition 2 and ECE amdt 1 ECE R13-H:2008 Revision 1 and amdt 1 SOUTH AFRICAN NATIONAL STANDARD Uniform provisions concerning the approval of passenger cars with
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-33757-5 Edition 4.1 IEC 60269-2:2016 Edition 5.1 SOUTH AFRICAN NATIONAL STANDARD Low-voltage fuses Part 2: Supplementary requirements for fuses for use by authorised persons (fuses mainly
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-32581-7 SOUTH AFRICAN NATIONAL STANDARD Gravity drainage systems inside buildings Part 3: Roof drainage, layout and calculation This national standard is the identical implementation of,
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-31092-9 IEC 62485-3:2014 SOUTH AFRICAN NATIONAL STANDARD Safety requirements for secondary batteries and battery installations Part 3: Traction batteries This national standard is the identical
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-24538-2 SOUTH AFRICAN NATIONAL STANDARD Transport of dangerous goods Design, construction, testing, approval and maintenance of road vehicles and portable tanks WARNING: Can only be read
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-29978-1 IEC 60079-17:2013 SOUTH AFRICAN NATIONAL STANDARD Explosive atmospheres Part 17: Electrical installations inspection and maintenance This national standard is the identical implementation
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-28543-2 Edition 2.1 and IEC corr. 1 IEC 62271-100:2012 Edition 2.1 and corr. 1 SOUTH AFRICAN NATIONAL STANDARD High-voltage switchgear and controlgear This national standard is the identical
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-26065-1 Edition 1 EN 12281:2002 Edition 2 SOUTH AFRICAN NATIONAL STANDARD Printing and business paper Requirements for copy paper for dry toner imaging processes This national standard is
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-23643-4 SOUTH AFRICAN NATIONAL STANDARD The testing of motor vehicles for roadworthiness WARNING This standard can only be used in conjunction with the relevant national legislation (see
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-30207-8 SOUTH AFRICAN NATIONAL STANDARD Chemicals used for treatment of water intended for human consumption Chlorine This national standard is the identical implementation of and is adopted
Part 7-2: Test methods Single cell and stack performance tests for solid oxide fuel cells (SOFC)
ISBN 978-0-626-30629-8 IEC TS 62282-7-2:2014 SABS STANDARDS DIVISION Technical specification Fuel cell technologies Part 7-2: Test methods Single cell and stack performance tests for solid oxide fuel cells
DRAFT SOUTH AFRICAN STANDARD (DSS): PUBLIC ENQUIRY STAGE
Document number 022/SANS 1496 Reference SANS 1496 DRAFT SOUTH AFRICAN STANDARD (DSS): PUBLIC ENQUIRY STAGE Date of circulation 2017-09-14 Closing date 2017-11-15 Number and title: SANS 1496:XXXX Wheel
SOUTH AFRICAN NATIONAL STANDARD
ISBN 0-626-18502-5 SANS 60335-2-76:2006 IEC 60335-2-76:2006 SOUTH AFRICAN NATIONAL STANDARD Household and similar electrical appliances Safety Part 2-76: Particular requirements for electric fence energizers
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-29507-3 EN 413-1:2011 SOUTH AFRICAN NATIONAL STANDARD Masonry cement Part 1: Composition, specifications and conformity criteria This national standard is the identical implementation of
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-28107-6 EN 1008:2002 SOUTH AFRICAN NATIONAL STANDARD Mixing water for concrete Specification for sampling, testing and assessing the suitability of water, including water recovered from
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-28152-6 EN 197-1:2011 SOUTH AFRICAN NATIONAL STANDARD Cement Part 1: Composition, specifications and conformity criteria for common cements This national standard is the identical implementation
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-27311-8 SANS 1332:2013 Edition 1 SOUTH AFRICAN NATIONAL STANDARD Accessories for medium-voltage XLPE and impregnated paper-insulated power cables (3,8/6,6 kv to 19/33 kv) This national standard
ISBN SANS 342:2006 Edition 4 SOUTH AFRICAN NATIONAL STANDARD Automotive diesel fuel Published by Standards South Africa 1 dr lategan roa
ISBN 0-626-18752-4 SOUTH AFRICAN NATIONAL STANDARD Automotive diesel fuel Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344
SOUTH AFRICAN NATIONAL STANDARD
ISBN 978-0-626-31521-4 EN 300:2006 SOUTH AFRICAN NATIONAL STANDARD Oriented Strand Boards (OSB) Definitions, classification and specifications This national standard is the identical implementation of
Is INTERNATIONAL STANDARD
INTERNATIONAL STANDARD Is0 4400 Third edition 1994-09-O 1 Fluid power systems and components - Three-pin electrical plug connectors with earth contact - Characteristics and requirements Transmissions hydrauliques
AS/NZS 3131:2001 AS/NZS
AS/NZS 3131:2015 Australian/New Zealand Standard Approval and test specification Plugs and socket-outlets for stationary appliances Superseding AS/NZS 3131:2001 AS/NZS 3131:2015 AS/NZS 3131:2015 This joint
SOUTH AFRICAN NATIONAL STANDARD
ICS 83.080.20; 83.140.30 ISBN 0-626-14156-7 SANS 12107:2003 SOUTH AFRICAN NATIONAL STANDARD Plastics piping systems Injection-moulded thermoplastics fittings, valves and ancillary equipment Determination
ISO 6264 INTERNATIONAL STANDARD. Hydraulic fluid power Pressure-relief valves Mounting surfaces
INTERNATIONAL STANDARD ISO 6264 Second edition 1998-03-01 Hydraulic fluid power Pressure-relief valves Mounting surfaces Transmissions hydrauliques Limiteurs de pression Plan de pose A Reference number
IS INTERNATIONAL STANDARD. systems - Road vehicles - Diagnostic Part 2: CARB requirements for inter& information.
INTERNATIONAL STANDARD IS0 9141-2 First edition 1994-02-01 Road vehicles - Diagnostic Part 2: CARB requirements for inter& information systems - lange of digital V6hicules routiers - Syst&mes de diagnostic
SOUTH AFRICAN NATIONAL STANDARD
ISBN 0-626-18752-4 SANS 342:2006 SOUTH AFRICAN NATIONAL STANDARD Automotive diesel fuel Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD IS0 7483 First edition 1991-10-01 --- ---- -.----.----_-- -_ ----- - - Dimensions of gaskets for use with flanges to IS0 7005 Dimensions des joints B utiliser avec les brides de
AS/NZS 3112:2004 AS/NZS
AS/NZS 3112:2011 Incorporating Amendment No. 1, 2, and 3 Australian/New Zealand Standard Approval and test specification Plugs and socket-outlets Superseding AS/NZS 3112:2004 AS/NZS 3112:2011 AS/NZS 3112:2011
Australian/New Zealand Standard
AS/NZS 3131 Australian/New Zealand Standard Approval and test specification Plugs and socket-outlets for stationary appliances This Joint Australian/New Zealand Standard was prepared by Joint Technical
Australian/New Zealand Standard
AS/NZS 10542.1:2009 AS/NZS 10542.1:2009 Australian/New Zealand Standard Technical systems and aids for disabled or handicapped persons Wheelchair tiedown and occupant-restraint systems Part 1: Requirements
ISO 2943 INTERNATIONAL STANDARD. Hydraulic fluid power Filter elements Verification of material compatibility with fluids
INTERNATIONAL STANDARD ISO 2943 Second edition 1998-11-15 Hydraulic fluid power Filter elements Verification of material compatibility with fluids Transmissions hydrauliques Éléments filtrants Vérification
Australian/New Zealand Standard
AS/NZS 4029.2:2000 AS/NZS 4029.2 Australian/New Zealand Standard Stationary batteries Lead-acid Part 2: Valve-regulated type (IEC 60896-2:1995, MOD) AS/NZS 4029.2:2000 This Joint Australian/New Zealand
Australian/New Zealand Standard
AS/NZS 3112:2011 AS/NZS 3112:2011 Australian/New Zealand Standard Approval and test specification Plugs and socket-outlets AS/NZS 3112:2011 This Joint Australian/New Zealand Standard was prepared by Joint
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 5692-1 First edition 2004-04-01 Corrected version 2004-09-15 Agricultural vehicles Mechanical connections on towed vehicles Part 1: Dimensions for hitch rings of 50/30 mm cross
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 10100 Second edition 2001-08-01 Hydraulic fluid power Cylinders Acceptance tests Transmissions hydrauliques Vérins Essais de réception Reference number ISO 10100:2001(E) ISO
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60086-1 Ninth edition 2000-11 Primary batteries Part 1: General Piles électriques Partie 1: Généralités IEC 2000 Copyright - all rights reserved No part of this publication may
REFERENCE REV CP_TSSPEC_016 1 TITLE SPECIFICATION FOR DATE: NOVEMBER 2010 LIGHTING TABLE OF CONTENTS Page FOREWORD INTRODUCTION
TITLE SPECIFICATION FOR CONTACTORS FOR PUBLIC LIGHTING REFERENCE REV DATE: NOVEMBER 2010 PAGE: 1 OF 16 TABLE OF CONTENTS Page FOREWORD.. 2 INTRODUCTION 3 1 SCOPE...... 3 2 NORMATIVE REFERENCES...... 3
Australian Standard. Pneumatic fluid power General requirements for systems (ISO 4414:1998, MOD) AS AS 2788
AS 2788 2002 AS 2788 Australian Standard Pneumatic fluid power General requirements for systems (ISO 4414:1998, MOD) This Australian Standard was prepared by Committee ME-035, Fluid Power Systems and Components.
This document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 1726 Third edition 2000-05-15 Road vehicles Mechanical coupling between tractors and semi-trailers Interchangeability Véhicules routiers Liaisons mécaniques entre tracteurs et
DEPARTMENT OF TRADE AND INDUSTRY NO APRIL 2016
Trade and Industry, Department of/ Handel en Nywerheid, Departement van 438 National Regulator for Compulsory Specifications Act (5/2008): Amendments to the Compulsory Specification for Earth Leakage Protection
ISO 8714 INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 8714 First edition 2002-11-01 Electric road vehicles Reference energy consumption and range Test procedures for passenger cars and light commercial vehicles Véhicules routiers
ISO INTERNATIONAL STANDARD. Road vehicles Test methods for electrical disturbances from electrostatic discharge
INTERNATIONAL STANDARD ISO 10605 First edition 2001-12-15 Road vehicles Test methods for electrical disturbances from electrostatic discharge Véhicules routiers Méthodes d'essai des perturbations électriques
Key-words: Plug. Socket-outlet
ABNT - Brazilian Association of Technical Standards Main office: Rio de Janeiro Av. Treze de Maio, 13 28th floor ZIP CODE 20003-900 P.0.box 1680 Rio de Janeiro - RJ Tel.: (21) 3974-2300 Fax: (21) 2240-8249/2220-6436
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60297-5-104 First edition 2001-01 Mechanical structures for electronic equipment Dimensions of mechanical structures of the 482,6 mm (19 in) series Part 5-104: Subracks and associated
ISO 3934 INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 3934 Second edition 2002-09-01 Rubber, vulcanized and thermoplastic Preformed gaskets used in buildings Classification, specifications and test methods Caoutchouc vulcanisé et
S T A N D A R D. ASAE S FEB04 Front and Rear Power Take-Off for Agricultural Tractors
ASAE S203.14 FEB04 Front and Rear Power Take-Off for Agricultural Tractors S T A N D A R D ASABE is a professional and technical organization, of members worldwide, who are dedicated to advancement of
S T A N D A R D. Copyright American Society of Agricultural and Biological Engineers. All rights reserved.
ANSI/ASAE S278.7 JUL03 (ISO 11001-1 1993) Agricultural wheeled tractors and implements Threepointhitch couplers Part 1: U-frame coupler S T A N D A R D ASABE is a professional and technical organization,
Australian/New Zealand Standard
AS/NZS 3001:2008 (Incorporating Amendment No. 1) AS/NZS 3001:2008 Australian/New Zealand Standard Electrical installations Transportable structures and vehicles including their site supplies AS/NZS 3001:2008
Electric vehicle charging system
TECHNICAL REFERENCE (ICS 43.120) TECHNICAL REFERENCE FOR Electric vehicle charging system Published by SPRING Singapore 2 Bukit Merah Central Singapore 159835 SPRING Singapore Website: www.spring.gov.sg
STANDARDS SOUTH AFRICA. Amendment No. 5 : May SANS :2006 (Ed 1.5) THE WIRING OF PREMISES PART 1: LOW-VOLTAGE INSTALLATIONS
STANDARDS SOUTH AFRICA Amendment No. 5 : May 2006 to SANS 10142-1:2006 (Ed 1.5) THE WIRING OF PREMISES PART 1: LOW-VOLTAGE INSTALLATIONS Approved in accordance with procedures of Standards South Africa.
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60297-5-102 First edition 2001-01 Mechanical structures for electronic equipment Dimensions of mechanical structures of the 482,6 mm (19 in) series Part 5-102: Subracks and associated
ISO 3996 INTERNATIONAL STANDARD. Road vehicles - Brake hose assemblies for hydraulic braking Systems used with non-petroleum-base brake fluid
INTERNATIONAL STANDARD ISO 3996 Third edition 1995-02-01 Road vehicles - Brake hose assemblies for hydraulic braking Systems used with non-petroleum-base brake fluid Vkhicules routiers - Flexibles pour
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 61851-1 First edition 2001-01 Electric vehicle conductive charging system Part 1: General requirements Dispositif de charge conductive pour véhicules électriques Partie 1: Prescriptions
Australian/New Zealand Standard
AS/NZS 3696.19:2009 AS/NZS 3696.19:2009 Australian/New Zealand Standard Wheelchairs Part 19: Wheeled mobility devices for use as seats in motor vehicles (ISO 7176-19:2008, MOD) AS/NZS 3696.19:2009 This
ISO INTERNATIONAL STANDARD. Aerospace Airframe needle roller, cylindrical roller and track roller bearings Technical specification
INTERNATIONAL STANDARD ISO 13411 First edition 1997-12-15 Aerospace Airframe needle roller, cylindrical roller and track roller bearings Technical specification Aéronautique et espace Roulements à aiguilles,
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60297-5-107 First edition 2001-01 Mechanical structures for electronic equipment Dimensions of mechanical structures of the 482,6 mm (19 in) series Part 5-107: Subracks and associated
Australian Standard. Caravan and light trailer towing components. Part 1: Towbars and towing brackets AS
AS 4177.1 2004 (Incorporating Amendment Nos 1 and 2) AS 4177.1 2004 Australian Standard Caravan and light trailer towing components Part 1: Towbars and towing brackets This Australian Standard was prepared
This document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 16852 Second edition 2016-10-15 Flame arresters Performance requirements, test methods and limits for use Arrête-flammes Exigences de performance, méthodes d essai et limites
TABLE OF CONTENTS FOREWORD... 2 INTRODUCTION SCOPE NORMATIVE REFERENCES DEFINITIONS AND ABBREVIATIONS... 3
TITLE SPECIFICATION FOR MEDIUM VOLTAGE DATE: FEBRUARY 2015 PAGE: 1 OF 25 TABLE OF CONTENTS Page FOREWORD... 2 INTRODUCTION... 3 1 SCOPE... 3 2 NORMATIVE S... 3 3 DEFINITIONS AND ABBIATIONS... 3 4 REQUIREMENTS...
ISO INTERNATIONAL STANDARD. Diesel engines End-mounting flanges for pumps Part 1: Fuel injection pumps
INTERNATIONAL STANDARD ISO 7299-1 First edition 2007-02-01 Diesel engines End-mounting flanges for pumps Part 1: Fuel injection pumps Moteurs diesels Brides de montage des pompes Partie 1: Pompes d'injection
SOUTH AFRICAN NATIONAL STANDARD
Copying nd network storge prohibited. ISBN 978-0-626-31934-2 SANS 62841-3-6:2016 Edition 1 nd IEC corr. 1 :2014 Edition 1 nd corr. 1 SOUTH AFRICAN NATIONAL STANDARD Electric motor-operted hnd-held tools,
ISO INTERNATIONAL STANDARD. Earth-mover tyres and rims Part 3: Rims. Pneumatiques et jantes pour engins de terrassement Partie 3: Jantes
INTERNATIONAL STANDARD ISO 4250-3 Fourth edition 2011-05-01 Earth-mover tyres and rims Part 3: Rims Pneumatiques et jantes pour engins de terrassement Partie 3: Jantes Reference number ISO 4250-3:2011(E)
Collection of standards in electronic format (PDF) 1. Copyright
Collection of standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance
This document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 10924-1 Second edition 2016-04-01 Road vehicles Circuit breakers Part 1: Definitions and general test requirements Véhicules routiers Coupe-circuits Partie 1: Définitions et
ISO INTERNATIONAL STANDARD. Seal-less rotodynamic pumps Class II Specification
INTERNATIONAL STANDARD ISO 15783 First edition 2002-02-01 Seal-less rotodynamic pumps Class II Specification Pompes rotodynamiques sans dispositif d'étanchéité d'arbre Classe II Spécifications Reference
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60470 Second edition 1999-10 High-voltage alternating current contactors and contactor-based motor-starters Contacteurs pour courants alternatifs haute tension et démarreurs
av elektromagnetisk energi Provningsmetoder för komplett fordon Del 2: Yttre strålningskälla
SVENSK STANDARD SS-ISO 11451-2 Fastställd 2001-11-16 Utgåva 2 Vägfordon Elstörningar från smalbandsemission av elektromagnetisk energi Provningsmetoder för komplett fordon Del 2: Yttre strålningskälla
This document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 1179-1 Second edition 2013-11-01 Connections for general use and fluid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 1: Threaded
AS/NZS :2013. Wheelchairs AS/NZS :2013. Australian/New Zealand Standard
AS/NZS 3695.2:2013 Australian/New Zealand Standard Wheelchairs Part 2: Requirements and test methods for electrically powered wheelchairs (including mobility scooters) Superseding AS 3695 1992 AS/NZS 3695.2:2013
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 1206 Third edition 2001-11-15 Rolling bearings Needle roller bearings, dimension series 48, 49 and 69 Boundary dimensions and tolerances Roulements Roulements à aiguilles, séries
ISO 1728 INTERNATIONAL STANDARD. Road vehicles Pneumatic braking connections between motor vehicles and towed vehicles Interchangeability
INTERNATIONAL STANDARD ISO 1728 Third edition 2006-09-01 Road vehicles Pneumatic braking connections between motor vehicles and towed vehicles Interchangeability Véhicules routiers Liaisons de freinage
Australian Standard. Electricity metering equipment (AC) Particular requirements
AS 62053.21 2005 Reconfirmed 2016 AS 62053.21 2005 Australian Standard Electricity metering equipment (AC) Particular requirements Part 21: Static meters for active energy (classes 1 and 2) (IEC 62053-21,
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 10100 Second edition 2001-08-01 Hydraulic fluid power Cylinders Acceptance tests Transmissions hydrauliques Vérins Essais de réception Reference number ISO 10100:2001(E) ISO
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60923 Edition 3.1 2006-09 Edition 3:2005 consolidated with amendment 1:2006 Auxiliaries for lamps Ballasts for discharge lamps (excluding tubular fluorescent lamps) Performance
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD IEC 60384-14 QC 302400 Third edition 2005-07 Fixed capacitors for use in electronic equipment Part 14: Sectional specification: Fixed capacitors for electromagnetic interference
Vägfordon Personbilar Provbana för kraftig undanmanöver Del 2: Undvikande av hinder
SVENSK STANDARD SS-ISO 3888-2 Fastställd 2002-12-13 Utgåva 1 Vägfordon Personbilar Provbana för kraftig undanmanöver Del 2: Undvikande av hinder Passenger cars Test track for a severe lane-change manoeuvre
ISO INTERNATIONAL STANDARD. Pneumatic fluid power Cylinders Final examination and acceptance criteria
INTERNATIONAL STANDARD ISO 10099 Second edition 2001-05-01 Pneumatic fluid power Cylinders Final examination and acceptance criteria Transmissions pneumatiques Vérins Critères de réception et de vérification
SVENSK STANDARD SS-ISO Hydraulik Bestämning av motorers karakteristik Del 1: Vid konstant låg hastighet och konstant tryck
SVENSK STANDARD SS-ISO 4392-1 Fastställd 2002-10-18 Utgåva 1 Hydraulik Bestämning av motorers karakteristik Del 1: Vid konstant låg hastighet och konstant tryck Hydraulic fluid power Determination of characteristics
Rubber hoses and hose assemblies Wire-braid-reinforced compact types for hydraulic applications Specification
BRITISH STANDARD BS ISO 11237-1:2004 Rubber hoses and hose assemblies Wire-braid-reinforced compact types for hydraulic applications Specification Part 1: Oil-based fluid applications ICS 23.100.40; 83.140.40
INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 10542-2 First edition 2001-07-15 Technical systems and aids for disabled or handicapped persons Wheelchair tiedown and occupant-restraint systems Part 2: Four-point strap-type
AS/NZS :2016. Grid connection of energy systems via inverters AS/NZS :2016. Part 1: Installation requirements
AS/NZS 4777.1:2016 Australian/New Zealand Standard Grid connection of energy systems via inverters Part 1: Installation requirements AS/NZS 4777.1:2016 AS/NZS 4777.1:2016 This joint Australian/New Zealand
ISO 6016 INTERNATIONAL STANDARD. Earth-moving machinery Methods of measuring the masses of whole machines, their equipment and components
INTERNATIONAL STANDARD ISO 6016 Second edition 1998-04-01 Earth-moving machinery Methods of measuring the masses of whole machines, their equipment and components Engins de terrassement Méthodes de mesure