DYNAMOMETERS ELECTRONIC/DIGITAL TRACTEL 270 DYNAMOMETERS PIAB 274 DYNAMOMETER ANALOG HI-TOOL 276 METER ROPE TENSION DILLON 277

Transcription

1

2

3 INDEX G. DYNAMOMETERS & LOAD CELLS DYNAMOMETERS ELECTRONIC/DIGITAL TRACTEL 270 DYNAMOMETERS PIAB 274 DYNAMOMETER ANALOG HI-TOOL 276 METER ROPE TENSION DILLON 277

4 DYNAMOMETERS ELECTRONIC/DIGITAL LLZ2 ELECTRONIC DYNAMOMETERS The TRACTEL dynafor LLZ2 is a precision industrial dynamometer to measure tensile forces or suspended loads. QUALITY Rugged and lightweight Integrated LCD screen Screen protected by strong protections side and front Battery life: 350 h Safety factor> 4 VERSATILITY Wide range available: 1t to 20t Usable in all positions, in combination with mooring of standard accessories Sealing IP65 / NEMA 4: Allows use of the device outside Temperature: -20 C to + 50 C ERGONOMICS Cut corners: risks minimized hooking during lifting operations Good readability: height of digits on the LCD: 18 mm ACCURACY Designed to measure tension efforts (Newtons) or suspended mass (kg) Accuracy 0.3% TECHNICAL CHARACTERISTICS Capacities from to kg High precision: ± 0.3% of Full Scale Supplied in plastic case with foam wedge Complies with Directive 2006/42/EC CE compliant SPECIFICATIONS Model No. LLZ2 1t LLZ2 3.2t LLZ2 6.3t LLZ2 12.5t LLZ2 20t WLL (tonne) Test Load (tonne) Safety Factor 4 Precision 0.3% Full Scale +/- (kg) Increment (kg) Maximum Display (kg) 110% of the WLL Conversion Factor Dynamic effects filter by sliding average calculation in 2 seconds Digit Height (mm) 17.8 Autonomy 350 Hours Weight (kg) IP Protection IP 65 Working T -20 to + 50 C Sensor Material Aluminium A B C Measurements (mm) D E F G H NOTE: Precision and Traceability Certified by Adjustment Certificate on 5 steps. 270

5 DYNAMOMETERS ELECTRONIC/DIGITAL LLX1 ELECTRONIC / DIGITAL DYNAMOMETERS Description The dynafor LLX1 dynamometers are precision force sensors used to measure forces and indicate loads. Enables use of standard shackles on both ends. Operating Principle Strain gauge measurement of the extension, within its limits of elasticity, of a metal body subjected to traction stress. The sensor generates an electrical signal that is proportional to the load. This signal is processed by a microprocessor analyser and then displayed on a build in LCD display. Technical Specifications Capacities from 500kg up to 20 Tonne Precision: 0.2% of full scale Safety coefficient : minimum 4 Power supply : 3 batteries 1.5VDC AA or 3 rechargeable batteries 1.2VDC AA Packaging : plastic carrying case Protection : IP 65 (NEMA 4) Options and accessories Radio Remote display, type LLX1. NEW Improved Electronics Design 40% Lighter (LLX) - Remote can be purchased with unit or later MODEL: LLX1-REMOTE SCAN & PLAY Model No. LLX1-0.5 LLX1-1 LLX1-2 LLX1-3.2 LLX1-5 LLX1-6.3 LLX LLX1-20 Maximum Capacity Tonne Test Load Tonne Safety Coefficient Minimum % FS Precision ± dan Increment dan Max. Display dan 110 % maximum capacity Number Height mm 18 Autonomy 450h (Batteries 1.5 V AA ) Weight kg IP Protection I.P. 65 Usafe From - 20 to 40 C Sensitivity to T 0.05% per 10 C Sensor Material Aluminium A B C Dimensions mm D E F G H Radio Option RF technology: Zigbee 2.4 GHz Range : 40 m in free field, see details

6 DYNAMOMETERS ELECTRONIC/DIGITAL LLX2 ELECTRONIC / DIGITAL DYNAMOMETERS DYNAFOR Offer an extensive range of load link dynamometers based on the strain gauges technology. This State-of-the art technology is utilised in the new generation LLX2 and LLXH, the connection between sensor and display, USB connection between display and PC, and monitoring software. DYNAFOR LLX2 devices are precision load indicators to measure tensile forces (N) and to determine hanging loads (kg). One DYNAFOR LLX2 units consists of a sensor and a remotely installed display (2.4GHz connection). Extended Range Comes in seven capacities: 0.5T, 1T, 2T, 3.2T, 5T, 6.3T and 10T. Removable Display The LLX2 display attaches securely to the sensor unit or can be held in your hand for remote operation. Crossed Fastening Planes The two axis of the sensor are crossed, enabling movements of lifting accessories on both sides, thus avoiding stresses due to load movements and enhancing appliance precision (Coplanar version available on request). Resistant To Shock and Weather The Dynafor LLX2 can be used indoors and outdoors, with excellent shock and moisture resistance, rated to IP66 protection. High Precision The Dynafor LLX2 has an accuracy of 0.1%, the industry standard. SPECIFICATIONS A Wireless Link with 80 Metre Range With its 2.4GHz frequency band, the Dynafor LLX2 provides a large operating range (80 metres) and can be used simultaneously in an environment with no risk of interference where a number of different devices are operating. High Endurance Sensor battery life: 300 to 1000 hours, depending on functions used, and 3000 hours while on standby. Display battery life: 48 hours while in use. Intuitive Commands Use of and access to the various functions is fast and easy. Interchangeable Displays The Dynafor LLX2 uses a single model display for all models, ensuring high utilisation and flexibility. Several Sensors and Displays can be Associated Up to 4 sensors can be associated to up to 4 displays each. PC Link The optional PC Connection Kit (PC to LLX2 via USB) allows advanced processing of measurement data. MODEL LLX2-0.5 LLX2-1 LLX2-2 LLX2-3.2 LLX2-5 LLX2-6.3 LLX2-10 Display Unit Maximum capacity Tonne All Test load Tonne Safety coefficient Minimum 4 Precision 0.1% according to ISO 376 at 21 C (I.P. 67 = 0.2%) dan Increment dan < Max. Display dan < Number height mm Autonomy From 300 to 1000 h depending of functions 48 h Radio scope m 80 (in open field) (IP67 = 60) RF Technology 2.4 Ghz Weight kg IP Protection IP 66 NEMA 4 (option : IP 67) IP 54 Usage From - 20 to 40 C Sensitivity to T 0.05% per 10 C Head Material Steel - Sensor Material Aluminium Steel - Dimensions mm SCAN & PLAY A B C Ø 20 Ø 20 Ø 20 Ø 20 Ø 28 Ø 28 Ø 40 - D E F G LLX2-3.2 shown 82mm 131mm 27mm 272

7 DYNAMOMETERS ELECTRONIC/DIGITAL LLXH ELECTRONIC / DIGITAL DYNAMOMETERS DYNAFOR Offer an extensive range of load link dynamometers based on the strain gauges technology. This State-of-the art technology is utilised in the new generation LLX2 and LLXH, the connection between sensor and display, USB connection between display and PC, and monitoring software. The dynafor LLXH (h for hybrid) are precision appliances for measuring pulling force and indicating loads. They combine the proven mechanical body of the LLX with the new electronic software from the LLX2. They are precise within +/- 0.2% and are available from 15T (150kN) to 250T (2,500kN). SPECIFICATIONS MODEL LLXH 15T LLXH 25T LLXH 50T LLXH 100T LLXH 250T Display LLXH-25T shown Maximum capacity Tonne ALL Test load Tonne mm Safety coefficient Minimum - 0.2% according to ISO C - Precision dan Increment dan < Max. display dan dan dan t t Number height mm Autonomy From 300 to 1000 h depending of functions 48 h Radio scope m 80 (in open field) (IP67 = 60) RF Technology 2.4 Ghz Weight kg IP Protection IP 65 (option : IP 67) IP 54 Usage From - 20 to 40 C Sensitivity to T 0.05% per 10 C Sensor material Aluminium - A B Dimensions C (mm) D E F < 27mm 131mm 273

8 DYNAMOMETERS PIAB PIAB DynamometeRS (MADE IN SWEDEN) The PIAB Dynamometer is excellent for measurement and control of tension forces, where accuracy, reliability and safety in all conditions is required. The PIAB Dynamometer is extremely robust and reliable instrument and is an all-weather instrument. Technical Data ACCURACY: ±0.6% of the max. capacity WORKING TEMPERATURE: Max.+60 C TAREING: The dynamometer can be tarred to approx.10% of the full scale. To obtain best accuracy the dynamometer should be supplied calibrated for a known tare. SCALE: White lacquered with black graduation. PROTECTION CLASS: IP 67, IEC 529 NEMA 4X Range of Application The PIAB Dynamometer is an all-weather instrument, equally suitable for use in the laboratory as out in the field for weighing and measuring mechanical forces. Function The pull rod movement operates the scale drum through a square thread stem. The power-absorbing element consists of specially made Belleville type spring washers, designed to be entirely free from wear. The spring washers cannot be overloaded. Safety Safety factor 5:1, guaranteed to withstand a load of 5 times full scale reading before rupture. The resistance to rupture is tested by the National Swedish Institute for Materials Testing. The PIAB Dynamometer may be overloaded by 100% without impairing the accuracy. The PIAB Dynamometers, types M-G, have drop-forged steel eye brackets (SIS 2174, St 52-3N acc. to DIN 17100, 50 D acc. to BS 4360); giving a guaranteed impact resistance to -20 C. The O-ring of the pull rod is protected by a neoprene rubber membrane. On instantaneous unloading, e.g. breaking test, the return movement of the pull rod is retarded by a specially made spring washer. The PIAB Dynamometer is approved by the National Board of Occupational Safety and Health for integral connection in the carrying system of a lifting device and for weighing of test loads in connection with inspection. Applications for the PIAB Dynamometer In line construction it is important to control the installed tension of conductors according to type and conditions. For field work light and robust equipment is especially important. The PIAB Dynamometers are used for this duty all over the world. Obligatory standards of control for occupational safety and health require that safety ropes and belts are regularly and properly checked. Dynamometer for remote reading The PIAB Dynamometer used for remote reading is supplied with a builtin precision potentiometer. The potentiometer is directly connected to the scale mechanism of the PIAB instrument. The electrical resistance of the potentiometer varies in proportion to the load on the dynamometer. The resistance is indicated on a receiving instrument, calibrated individually and marked with the same serial number as the dynamometer. The electrical connections are made on a connection block in a surface mounted connection box. Contact function The PIAB Dynamometer can be equipped with a built-on adjustable Switch Head. Using a Microswitch, which is directly influenced by the pull rod, the PIAB Dynamometer gives an electrical contact function at a preset value. For further technical specifications please refer to PIAB Info PIAB Switch Head Dynamometer. Protection against corrosion The PIAB Dynamometer is fully pressure tight and each instrument is pressure tested. The external surfaces are zinc plated with clear chromate passivation. If the PIAB Dynamometer is to be used in a very corrosive atmosphere, it can be polyester lacquered. This electrical overhead traveling crane is protected against overload by a PIAB Dynamometer in the hook line anchorage, giving the crane operator the actual load on the hook together with overload warnings and power shunt. 274

9 DYNAMOMETERS PIAB PIAB Dynamometer function The pull rod movement operates the scale drum through a square thread stem. The power-absorbing element consists of specially made Belleville type spring washers, so designed as to be entirely free from wear. The spring washers cannot be overloaded. The PIAB Dynamometer can be overloaded with 100% without affecting the accuracy. Can temporarily be overloaded by 100% without affecting the accuracy. Fully pressure tight, and each instrument is pressure tested. The PIAB Dynamometer can be equipped for remote reading or contact functions (micro switches). Available with polyester lacquering for use in very corrosive environment (optional). Model No TYPE K NK A NA B NB B x 1.5 NB x 1.5 M NM O NO Q NQ S SQ U NU G NG Capacity Graduations Weight Measurements in mm kg/n 1 Mm Kg A B C D E F G H I J x K 250kg 2,500N 500kg 5,000N 1,000kg 10kN 1,500kg 15kN 2,000kg 20kN 3,000kg 30kN 5,000kg 50kN 10,000kg 100kN 20,000kg 200kN 25,000kg 250kN 5 50N N N N N N N 100 1kN 200 2kN kN x x x E NE 50,000kg 500kN kN

10 DYNAMOMETER ANALOG DYNAMOMETERS AND LOAD CELLS (MADE IN JAPAN) FEATURES Compact, lightweight, rugged construction. Designed for line work. Graduated in kn (1 kilo newton kn = 102 kg force). Accuracy +/- 3% full scale. Both pulling eyes rotate 360. Optional maximum reading indicator pointer kit available for easy installation. Optional easily installed screw-on face with twin steel protective bars also available. Each tool is serial numbered and supplied in a heavy duty fabric case with calibration certificate. D B Model No. Capacity (kn) A Capacity (Tonne) Graduation (kn) C A (mm) B - Body Ø (mm) C (mm) D (mm) TM-5 COMPLETE* TM-10 COMPLETE* TM-20 COMPLETE* TM-30 COMPLETE* TM-50 COMPLETE* TM-100 COMPLETE* *SUPPLIED WITH PROTECTION BARS & MAX LOAD INDICATOR SPARE PARTS GLASS PROTECTION BARS Model No. TM5/30 BARS Suits TM-5 to TM-30 Dynamometers Model No. TM50/100 BARS Suits TM-50 to TM-100 Dynamometers MAXIMUM LOAD INDICATOR Model No. TM5/30 POINTER Suits TM-5 to TM-30 Dynamometers Model No. TM50/100 POINTER Suits TM-50 to TM-100 Dynamometers Durable & Reliable Weight (kg) 276

11 METER ROPE TENSION QUICK CHECK RED TENSION METER The Dillon Quick-Check RED Tension Meter quickly measures tension in cable guardrails, guy lines and overhead wires. It installs, measures and removes in seconds. The digital load cell is highly accurate and requires no lookup or correction tables. The Fastest Cable Tension Meter The Dillon Quick-Check can be placed on a cable, measure its tension, and removed in under five seconds! There are no complex lookup tables, no conversion charts. The operator can quickly select from 20 different wire sizes and types stored in Quick-Check s memory. The Check-Tensioning mode graphically displays the current and target tensions for extremely quick setting of line tension. Even the infrequent battery changes are quick. Broad Application The Quick-Check can be employed in many industries to ensure proper tensioning. Typical applications include tower and stack guy wires, pretensioned cable barriers, bridges, elevators, winch rope, prestressed concrete, aircraft cables, overhead railway transit wires, fall arrest systems and utilities. FEATURES Accommodates a wide range of wire sizes and styles Telescoping handle length facilitates easy placement on cable Built-in averaging saves time and eliminates errors Stores calibrations for up to 20 unique wire sizes and types Stores wire rope reading and export data (RS-232 port) Built-in temperature sensor with patented automatic tension adjustment Sheaves with bearings eliminate friction and provide the best accuracy Easy-to-read backlit display with full-text prompts and easy to use soft key interface Uses standard AA batteries and has a long life. over 250 hrs continuous* *10hZ = over 250hrs continuous 100hZ = over 100hr continuous (Tested with backlight off) Time saving check-tensioning mode Portable and rugged designed for outdoor use *Carry Case included SPECIFICATIONS OF UNIT Tension Model No. Capability (kn/kg) AWT /1000 AWT / MTS (Included) Wire Size (mm) Accuracy* (±) % No. of Calibrations Up to 15 Independent Temp Range ºC Sheave Range (mm) ¹ -20 to 70 <12.7 Re-Calibration 24 Months, Sooner with Frequent Use Size (cm) Wt (kg) 25x59x8 5 Carry Case - Medium Duty, Die Cut Density Foam 70x41x * ±3% instrument capacity (calibrated to specific wire size & type, ±5% with same wire diameter as calibrated but different wire type). ¹ Sheave accommodates rated wire size and 12.7mm smaller. Sheaves are not compatible with larger wire sizes order additional sheaves for wire sizes. SELECT SHEAVE (Other sheave sizes available upon request) Model No. Sheave Code Accommodates Wire Diameters (mm) L P S T EXAMPLE OF ORDER Model No. Description AWT Quick Check Meter Sheave Code S (6.5-19mm) 1st Calibration (FREE) For Wire 15.88mm (1x19) 2nd Calibration For Wire 12.70mm (1x7) 3rd Calibration For Wire 9.53 (1x7) MTS Carry Case SCAN & PLAY Note that the first wire calibration is free, all others are charged, with pricing reduced the more you order (Categories are 2-5, 6-10 & 11-15). Please contact Specialised Force to discuss your requirements, units programmed specifically to order Order a quick check meter used to tension up to 45kN wires; 15.88mm (1x19), 12.70mm (1x7) and 9.53mm (1x7) with carry case. DILLON Dynamometers also Available Upon Request 277