ENGINE MECHANICAL PREPARATION SST mm Socket Wrench for 12 Pointed Head Union Nut Wrench 12mm PARTIAL ENGINE ASSY(1ZZ FE)
|
|
|
- Tobias Gardner
- 5 years ago
- Views:
Transcription
1 SST E mm Socket Wrench for 12 Pointed Head CYLINDER BLOCK(1ZZFE) Union Nut Wrench 12mm Oil Pan Seal Cutter Valve Guide Bushing Remover & Replacer 5.5 CYLINDER HEAD ASSY(1ZZFE) Valve Guide Bushing Remover & Replacer Set CYLINDER HEAD ASSY(1ZZFE) Valve Stem Oil Seal Replacer CYLINDER HEAD ASSY(1ZZFE) Valve Spring Compressor CYLINDER HEAD ASSY(1ZZFE) ( ) Attachment CYLINDER HEAD ASSY(1ZZFE) ( ) Arm CYLINDER HEAD ASSY(1ZZFE) ( ) Set Bolt CYLINDER HEAD ASSY(1ZZFE) Cylinder Head Bolt Wrench CYLINDER BLOCK(1ZZFE) Crankshaft Pully Holding Tool ENGINE REAR OIL 51
2 026 ( ) Bolt ENGINE REAR OIL Oil Seal & Bearing Replacer ENGINE REAR OIL SEAL(1ZZFE) Oil Seal & Bearing Replacer ENGINE REAR OIL Crankshaft Front Oil Seal Replacer CHAIN SUBASSY(1ZZFE) SEAL(1ZZFE) CYLINDER HEAD GASKET(1ZZFE) O2 Sensor Wrench Oil Filter Wrench Valve Clearance Adjusting Compressor Set VALVE CLEARANCE(2ZZGE) ( ) Valve Clearance Adjusting Compressor VALVE CLEARANCE(2ZZGE) Fuel Hose Puller CYLINDER HEAD GASKET(1ZZFE) Nozzle Holder Retaining Nut Wrench Clutch Guide Tool ENGINE REAR OIL 52
3 Companion Flange Holding Tool ENGINE REAR OIL Drive Shaft Remover Attachment Differential Side Gear Shaft Puller ( ) Shocker Set Boll Joint Puller Front Crossmember Guide Tool Sensor Socket Wrench Diagnosis Check Wire No.2 ENGINE ASSEMBLY(1ZZFE) CYLINDER HEAD GASKET(1ZZFE) ENGINE ASSEMBLY(2ZZGE) Drive Shaft Nut Chisel Puller C Set ( ) Hanger 150 ( ) Slide Arm 53
4 028 ( ) Center Bolt 150 ( ) Claw No.2 ( ) Attachment Replacer Set ( ) Replacer 25 ( ) Replacer 35 ( ) Replacer Handle Set ENGINE REAR OIL SEAL(1ZZFE) CYLINDER HEAD ASSY(1ZZFE) ENGINE REAR OIL ( ) Handle 100 ENGINE REAR OIL SEAL(1ZZFE) CYLINDER HEAD ASSY(1ZZFE) ENGINE REAR OIL Variable Pin Wrench Set CHAIN SUBASSY(1ZZFE) SEAL(1ZZFE) ENGINE REAR OIL SEAL(1ZZFE) CYLINDER HEAD GASKET(1ZZFE) 54
5 029 ( ) Variable Pin Wrench Arm Assy CHAIN SUBASSY(1ZZFE) SEAL(1ZZFE) ENGINE REAR OIL SEAL(1ZZFE) CYLINDER HEAD GASKET(1ZZFE) ( ) Pin 6 ( ) Pin 10 CHAIN SUBASSY(1ZZFE) SEAL(1ZZFE) ENGINE REAR OIL SEAL(1ZZFE) CYLINDER HEAD GASKET(1ZZFE) Compression Gauge Attachment ENGINE ASSEMBLY(1ZZFE) CYLINDER HEAD GASKET(1ZZFE) ENGINE ASSEMBLY(2ZZGE) Recomended Tools Socket Wrench 30 mm Pin Punch. CYLINDER HEAD ASSY(1ZZFE) Hexagon Wrench Set ( ) Socket Hexagon Wrench 5 ( ) Socket Hexagon Wrench 10 CYLINDER HEAD ASSY(1ZZFE) ( ) Socket Hexagon Wrench Bihexagon Wrench 10 mm Engine Sling Device 55
6 0210 SSM Seal Packing Black or equivalent (FIPG) Seal Packing 1282B, THREE BOND 1282B or equivalent (FIPG) CHAIN SUBASSY(1ZZFE) CAMSHAFT(1ZZFE) CYLINDER HEAD GASKET(1ZZFE) VALVE CLEARANCE(1ZZFE) CYLINDER BLOCK(1ZZFE) CAMSHAFT(2ZZGE) VALVE CLEARANCE(2ZZGE) Adhesive 1324, THREE BOND 1324 or equivalent Adhesive 1344 THREE BOND 1344 LOCTITE 242 or equivalent ENGINE REAR OIL SEAL(1ZZFE) CYLINDER HEAD ASSY(1ZZFE) ENGINE REAR OIL CYLINDER BLOCK(1ZZFE) Equipment Alignment tester Caliper gauge Chain Block CO/HC meter Compression gauge Connecting rod aligner Cylinder gauge Dial indicator Feeler gauge Heater Hexagon wrench (5mm) Micrometer OBD II scan tool Piston ring compressor Piston ring expander Plastic Hammer Plastigage Precision straight edge Radiator cap tester Reamer Sandpaper (#400) Slide calipers Steel square Straight edge Spring tester 56
7 0211 Spring tension gauge Tire pressure gauge Toein gauge Torque wrench Universal engine lifter Valve seat cutter Vernier calipers Vblock Wooden block 57
ENGINE MECHANICAL PREPARATION SST mm Socket Wrench for 12 Pointed Head
SST 027 023HH01 0901138121 12 mm Socket Wrench for 12 Pointed Head CYLINDER BLOCK ASSY(2AZFE) PARTIAL ENGINE ASSY(3MZFE) (3MZFE) NO.2(3MZFE) CYLINDER BLOCK ASSY(3MZFE) 0903200100 Oil Pan Seal Cutter PARTIAL
1NZ-FE ENGINE CONTROL SYSTEM
PREPARATION 1NZ-FE ENGINE CONTROL SYSTEM 1NZ-FE ENGINE CONTROL SYSTEM PREPARATION SST 1 09817-33190 Sensor Socket Wrench 2 PREPARATION 1NZ-FE ENGINE CONTROL SYSTEM RECOMMENDED TOOLS 09082-00040 TOYOTA
ENGINE CONTROL SYSTEM
ENGINE CONTROL SYSTEM Recommended Tools ENGINE CONTROL SYSTEM 021 023FY01 0907020010 Moulding Remover ECM(1NZFXE) 0908200040 TOYOTA Electrical Tester SFI SYSTEM(1NZFXE) (0908300150) Test Lead Set SFI SYSTEM(1NZFXE)
2AZ-FE ENGINE CONTROL SYSTEM
PREPARATION 2AZ-FE ENGINE CONTROL SYSTEM 2AZ-FE ENGINE CONTROL SYSTEM PREPARATION SST 1 09817-33190 Sensor Socket Wrench Engine coolant temperature sensor 2 PREPARATION 2AZ-FE ENGINE CONTROL SYSTEM RECOMMENDED
DIAGNOSTICS PREPARATION SST. Recomended Tools Oil Pressure Switch Socket SFI SYSTEM Diagnosis Check Wire No.
DIAGNOSTICS SST DIAGNOSTICS 021 021CL01 0981630010 Oil Pressure Switch Socket SFI SYSTEM 0984318040 Diagnosis Check Wire No.2 SFI SYSTEM SUPPLEMENTAL SYSTEM RESTRAINT Recomended Tools 0908200040 TOYOTA
1GR-FE ENGINE CONTROL SYSTEM
PREPARATION 1GR-FE ENGINE CONTROL SYSTEM 1GR-FE ENGINE CONTROL SYSTEM PREPARATION RECOMMENDED TOOLS 1 09040-00011 Hexagon Wrench Set (09043-20080) Socket Hexagon Wrench 8 (09043-20100) Socket Hexagon Wrench
PP-1 16 PP0E4-03 EQUIPMENT. Voltmeter Ammeter Ohmmeter Test lead. Torque wrench
PP1 16 AIR CONDITIONING EQUIPMENT PP0E403 Voltmeter Ammeter Ohmmeter Test lead Thermometer Torque wrench Dial indicator Plastic hammer Hexagon wrench Thermistor Magnetic clutch Magnetic clutch Expansion
OVERHAUL. 1. REMOVE W/HEAD TAPER SCREW PLUG NO.2 (a) Using a socket hexagon wench 10, remove the taper screw plug and gasket.
14138 ENGINE MECHANICAL OVERHAUL 140Q703 1. REMOVE W/HEAD TAPER SCREW PLUG NO.2 (a) Using a socket hexagon wench 10, remove the taper screw plug and gasket. A62890 2. REMOVE VALVE LIFTER (a) Remove the
PREPARATION MAINTENANCE... ENGINE MECHANICAL... EMISSION CONTROL... ELECTRONIC FUEL INJECTION... LUBRICATION...
PREPARATION MAINTENANCE......................... ENGINE MECHANICAL................... EMISSION CONTROL.................... ELECTRONIC FUEL INJECTION.......... COOLING............................... LUBRICATION...........................
PP-80 PP1AG-01 EQUIPMENT. Voltmeter Ammeter Ohmmeter Test lead. Torque wrench 2004 LAND CRUISER (RM1071U)
PP80 AIR CONDITIONING EQUIPMENT PP1AG01 Voltmeter Ammeter Ohmmeter Test lead Thermometer Sernsor Torque wrench Dial indicator Magnetic clutch Plastic hammer Magnetic clutch 139 AIR CONDITIONING PP81 LUBRICANT
OVERHAUL 1. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB ASSY
1416 OVERHAUL 1. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUBASSY 140RL01. INSPECT CONNECTING ROD THRUST CLEARANCE (a) Using a dial indicator, measure the thrust clearance while moving the connecting rod
CYLINDER HEAD ASSY (1MZ FE)
OVERHAUL 1. REMOVE W/HEAD STRAIGHT SCREW PLUG NO.1 14209 1405K01 Using a 14 mm straight hexagon wrench, remove the screw plug. 2. REMOVE W/HEAD STRAIGHT SCREW PLUG NO.2 Using a 14 mm straight hexagon wrench,
OVERHAUL. 1. REMOVE VALVE LIFTER HINT: Arrange the valve lifter in the correct order.
ENGINE MECHNICL 1473 OVERHUL 1415F02 1. REMOVE VLVE LIFTER HINT: rrange the valve lifter in the correct order. 75601 SST Wooden Block 75602 2. REMOVE VLVE HINT: rrange the valves, inner compression springs,
2AZ-FE Engine Oil Consumption Repair Procedure
S-SB-0024-11 Rev2 August 11, 2011 Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2007 2010 tc Engine(s): 2AZ VDS(s): DE167,
INSTALLATION EM 8 1NZ-FE ENGINE MECHANICAL DRIVE BELT INCORRECT CORRECT. Generator Vehicle Front A077960E03. Adjusting Bar. Bolt A. Bolt B.
8 CORRECT Adjusting Bar 1NZ-FE ENGINE MECHANICAL DRIVE BELT INCORRECT Generator Vehicle Front A077960E03 INSTALLATION 1. INSTALL VANE PUMP V BELT (a) Temporarily install the belt on each pulley. 2. INSTALL
2AZ-FE Engine Oil Consumption
T-SB-0094-11 Rev2 August 11, 2011 Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2007 2011 Camry HV Engine(s): 2AZ VDS(s):
Toyota Truck Pickup 2WD L4-2.4L SOHC (22R) 1987
Timing Chain: Service and Repair Toyota Truck Pickup 2WD L4-2.4L SOHC (22R) 1987 PREPARATION FOR REMOVAL OF TIMING CHAIN 1. REMOVE CYLINDER HEAD 2. REMOVE RADIATOR 3. REMOVE OIL PAN (a) Remove the engine
CO/HC INSPECTION HINT:
CO/HC CO/HC INSPECTION EM1 EM0KQ07 This check is used only to determine whether or not the idle CO/ HC complies with regulations. 1. INITIAL CONDITIONS (a) The engine is at normal operating temperature.
2AZ-FE Engine Oil Consumption
T-SB-0094-11 August 11, 2011 Service Category Engine/Hybrid System Section Lubrication Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2007 2011 Camry HV Engine(s): 2AZ VDS(s): BB3EK,
RECOMMENDED TOOLS AND CHECKERS. Page RECOMMENDED TOOLS AND CHECKERS... 2
RECOMMENDED TOOLS AND CHECKERS Page RECOMMENDED TOOLS AND CHECKERS........... 2 4 1 09010-3C100 Hexagon Wrench Set (09013-6C100) ( Wrench 5 ) (09013-6C110) ( Wrench 6 ) (09013-6C120) ( Wrench 8 ) (09013-6C130)
OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE CYLINDER HEAD COVER SUB ASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket.
144 ENGINE MECHANICAL OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 1410H01 2. REMOVE CYLINDER HEAD COVER SUBASSY (a) Remove the 10 bolts, 2 nuts, cylinder head cover and gasket. A11090 3. REMOVE CAMSHAFT
OVERHAUL 1. REMOVE OIL FILLER CAP SUB ASSY. 2. REMOVE OIL FILLER CAP GASKET (a) Using a screwdriver, remove the gasket from the oil filter cap.
14218 ENGINE MECHANICAL PARTIAL ENGINE ASSY (2ZZGE) OVERHAUL 1. REMOVE OIL FILLER CAP SUBASSY 140R901 2. REMOVE OIL FILLER CAP GASKET (a) Using a screwdriver, remove the gasket from the oil filter cap.
INSPECTION. (b) Using a wire brush, remove all the carbon from the combustion NOTICE:
EM44 ENGINE MECHANICAL (2RZFE, 3RZFE) INSPECTION EM16R02 1. CLEAN TOP SURFACES OF PISTONS AND CYL- INDER BLOCK (a) Turn the crankshaft, and bring each piston to top dead center (TDC). (b) Using a gasket
INSPECTION. (b) Using a wire brush, remove all the carbon from the combustion NOTICE:
EM44 INSPECTION EM11E01 1. CLEAN TO P SURFACES O F PI STO NS AND CYL- INDER BLOCK (a) Turn the crankshaft, and bring each piston to top dead center (TDC). Using a gasket scraper, remove all the carbon
INSPECTION. (b) Using a wire brush, remove all the carbon from the combustion NOTICE:
EM38 ENGINE MECHANICAL (5VZFE) INSPECTION EM16E02 1. CLEAN TOP SURFACES OF PISTONS AND CYL- INDER BLOCK (a) Turn the crankshaft and bring each piston to top dead center (TDC). (b) Using a gasket scraper,
VALVE CLEARANCE (1NZ-FXE)
146 ENGINE MECHANICAL ADJUSTMENT 1. REMOVE REAR FLOOR BOARD NO.2 (See page 211 16) 2. REMOVE DECK FLOOR BOX REAR (See page 211 16) 3. REMOVE REAR FLOOR BOARD NO.3 (See page 211 16) 4. DISCONNECT BATTERY
CYLINDER HEAD COMPONENTS FOR REMOVAL AND INSTALLATION
3SGTE ENGINE EG171 CYLINDER HEAD COMPONENTS FOR REMOVAL AND INSTALLATION EG172 3SGTE ENGINE 3SGTE ENGINE EG173 EG174 3SGTE ENGINE REMOVAL OF CYLINDER HEAD (See Components for Removal and Installation)
CO/HC INSPECTION HINT:
ENGINE MECHANICAL (2UZFE) CO/HC CO/HC INSPECTION HINT: EM1 EM0KQ09 This check is used only to determine whether or not the idle CO/ HC complies with regulations. 1. INITIAL CONDITIONS (a) Engine at normal
MIL "ON" DTC P030#, Intermittently Runs Rough, and/or Engine Oil Consumption
L-SB-0068-11 Rev1 August 11, 2011 MIL "ON" DTC P030#, Intermittently Runs Rough, and/or Engine Oil Consumption Service Category Engine/Hybrid System Section Engine Control Market USA Applicability YEAR(S)
MIL "ON" DTC P030#, Intermittently Runs Rough, and/or Engine Oil Consumption
L-SB-0124-12 November 30, 2012 MIL "ON" DTC P030#, Intermittently Runs Rough, and/or Engine Oil Consumption Service Category Engine/Hybrid System Section Engine Control Market USA Applicability YEAR(S)
EM 128 2UZ-FE ENGINE MECHANICAL ENGINE UNIT INSPECTION
128 2UZ-FE ENGINE MECHANICAL ENGINE UNIT INSPECTION HINT: Thoroughly clean all parts to be assembled. Before installing the parts, apply new engine oil to all sliding and rotating surfaces. Replace all
ACCREDITATION FACILITY AUDIT CHECKLIST
ACCREDITATION FACILITY AUDIT CHECKLIST Institution Name: Date: Designated Trade: Marine and Outdoor Power Equipment Technician AC #: Contact: Location: Course Duration: of weeks: of hours total: of hours
2ZR-FXE Engine Oil Consumption Repair Procedure
T-SB-0169-16 November 16, 2016 Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2010, 2012-2014 Prius PHV 2012-2014 Prius
2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE)
2005 Toyota Truck RAV4 2WD L4 2.4L (2AZ FE) Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair TIMING CHAIN TIMING CHAIN http://alldatapro.com/alldata/pro~v440713400~c39519~r0~od~n/0/108596970/110859775/110859788/110859790/34853741/100411974/34853743/56492475
OVERHAUL. 1. REMOVE OIL FILLER CAP SUB ASSY (a) Remove the oil filler cap from the cylinder head cover.
1452 ENGINE MECHNICL OVERHUL 140QU01 1. REMOVE OIL FILLER CP SUSSY (a) Remove the oil filler cap from the cylinder head cover. 64852 2. REMOVE OIL FILLER CP GSKET (a) Using a screwdriver, remove the gasket
DISASSEMBLY. 1. INSTALL ENGINE TO ENGINE STAND FOR DIS- ASSEMBLY 2. REMOVE CYLINDER HEAD (See page EM 29)
DISASSEMBLY EM67 EM9Q0. INSTALL ENGINE TO ENGINE STAND FOR DIS- ASSEMBLY. REMOVE CYLINDER HEAD (See page EM9). REMOVE WATER BYPASS PIPE Remove the nuts, bolts, water bypass pipe and gasket.. REMOVE THERMOSTAT
V160 MANUAL TRANSMISSION MT2 1
MT21 MT22 V160 MANUAL TRANSMISSION PREPARATION SST (SPECIAL SERVICE TOOLS) 0930810010 Oil Seal Puller PREPARATION 0930814010 Replacer Pipe A 0930914040 Remover & Replacer D 0933000021 Companion Flange
INSPECTION. (b) Clean the combustion chambers. Using a wire brush, remove all the carbon from the combustion NOTICE:
ENGINE MECHANICAL (2JZGE) INSPECTION EM41 EM0DC05 1. CLEAN TOP SURFACES OF PISTONS AND CYL- INDER BLOCK (a) Turn the crankshaft, and bring each piston to top dead center (TDC). Using a gasket scraper,
2005 Toyota RAV AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul
2001-05 AUTOMATIC TRANSMISSIONS U240E & U241E Overhaul APPLICATION CAUTION: Flush oil cooler and oil cooler lines prior to transaxle installation. Oil cooling system contamination may cause premature transaxle
CYLINDER HEAD GASKET (2AZ-FE)
190 REPLACEMENT 1. WORK FOR PREVENTING GASOLINE FROM SPILLING OUT (See page 111 ) 2. REMOVE FRONT SUSPENSION UPPER BRACE CENTER (W/ FRONT SUSPENSION BRACE UPPER CENTER) 3. REMOVE CHAIN SUBASSY (See page
EM 112 1GR-FE ENGINE MECHANICAL ENGINE ASSEMBLY INSPECTION. Intake Air Surge Tank Side
112 Intake Air Surge Tank Side Cylinder Head Side 1GR-FE ENGINE MECHANICAL ENGINE ASSBLY INSPECTION 1. INSPECT INTAKE MANIFOLD FOR WARPAGE (a) Using a precision straight edge and feeler gauge, measure
26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]
![26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]](/thumbs/85/92233007.jpg "26/01/2017 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/ ]")
Last Modified: 8-24-2016 6.6 A Doc ID: RM000000T4X000X Model Year Start: 2006 Model: GS300 Prod Date Range: [01/2005 - ] Title: 3GR-FSE ENGINE MECHANICAL: ENGINE UNIT: DISASSEMBLY; 2006 MY GS300 [01/2005
TIMING CHAIN COMPONENTS
h Page 1 of 52 TIMING CHAIN COMPONENTS ht Page 2 of 52 Fig. 24: Displaying Timing Chain Components (1 Of 2) Page 3 of 52 Fig. 25: Displaying Timing Chain Components (2 Of 2) Page 4 of 52 REMOVAL NOTE:
REASSEMBLY MT INSTALL 1ST AND REVERSE SHIFT ARM (a) Install the shift arm and shift arm pivot onto the interlock bracket.
30 RA61F MANUAL TRANSMISSION MANUAL TRANSMISSION UNIT REASSEMBLY 1. INSTALL 1ST AND REVERSE SHIFT ARM (a) Install the shift arm and shift arm pivot onto the interlock bracket. D033725 (b) Install a new
AUTOMATIC TRANSAXLE AUTOMATIC TRANSAXLE SYSTEM... COMPONENT PARTS...
SYSTEM....... COMPONENT PARTS.................... OIL PUMP.............................. DIRECT CLUTCH........................ FORWARD CLUTCH..................... SECOND BRAKE........................ UNDERDRIVE
SST AND SSM. Page SST (SPECIAL SERVICE TOOLS)... C-2 SSM (SPECIAL SERVICE MATERIALS)... C-18
SST AND SSM Page SST (SPECIAL SERVICE TOOLS)... C-2 SSM (SPECIAL SERVICE MATERIALS)... C-18 C -2 SST AND SSM - SST (Special Service Tools) SST (SPECIAL SERVICE TOOLS) Illustration 011 Pan Seal Cutter Hexagon
SUSPENSION AND AXLE SA 1
SUSPENSION AND AXLE SA1 SA2 TROUBLESHOOTING SUSPENSION AND AXLE TROUBLESHOOTING Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely cause of the
CO/HC INSPECTION HINT:
CO/HC Meter CO/HC CO/HC INSPECTION HINT: EM1 EM03T03 This check is used only to determine whether or not the idle CO/ HC complies with regulations. 1. INITIAL CONDITIONS (a) Engine at normal operating
DF 15. DIFFERENTIAL 1GR-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) REMOVAL
DIFFERENTIAL 1GR-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) 15 REMOVAL 1. REMOVE FRONT WHEELS 2. REMOVE REAR ENGINE UNDER COVER ASSEMBLY (a) Remove the 6 bolts and engine under cover assembly. 3.
POWER STEERING SYSTEM
SYSTEM 511 SYSTEM PRECAUTION 5105K01 1. HANDLING PRECAUTIONS ON STEERING SYSTEM (a) Care must be taken to when replacing parts. Incorrect replacement could affect the performance of the steering system
CO/HC INSPECTION HINT:
ENGINE MECHANICAL (1MZFE) CO/HC Meter CO/HC CO/HC INSPECTION HINT: EM1 EM0I0 This check is used only to determine whether or not the idle CO/ HC complies with regulations. 1. INITIAL CONDITIONS (a) Engine
2004 Toyota RAV ENGINE Lubrication - RAV4
2004 ENGINE Lubrication - RAV4 OIL AND FILTER INSPECTION 1. CHECK ENGINE OIL QUALITY Check the oil for deterioration, entry of water, discoloring or thinning. If the quality is visibly poor, replace the
Oil Pan Seal Cutter Oil Filter Wrench Transmission & Transfer Bearing Replacer. ( ) Replacer Pipe
EG359 PREPARATION SST (SPECIAL SERVICE TOOLS) 0903200100 Oil Pan Seal Cutter No.2 oil pan 0922807500 Oil Filter Wrench 0931660010 Transmission & Transfer Bearing Replacer (0931600010) Replacer Pipe Crankshaft
2.2L 4-CYL - VIN [S]
![2.2L 4-CYL - VIN [S]](/thumbs/72/67564355.jpg "2.2L 4-CYL - VIN [S]")
2.2L 4-CYL - VIN [S] 1994 Toyota Celica 1994 ENGINES Toyota 2.2L 4-Cylinder Celica NOTE: For repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article
EM 84 ENGINE MECHANICAL (2RZ FE, 3RZ FE) EM16Y 02 DISASSEMBLY
EM84 ENGINE MECHANICAL (2RZFE, 3RZFE) EM16Y02 DISASSEMBLY 1. M/T: REMOVE FLYWHEEL Remove the 10 bolts and flywheel. 2. A/T: REMOVE DRIVE PLATE Remove the 10 bolts, front spacer, drive plate and rear plate.
20.Cylinder Block. Cylinder Block A: REMOVAL ME(H4DOTC)-63 ST CRANKSHAFT STOPPER
Cylinder Block MECHANICAL 20.Cylinder Block A: REMOVAL Before conducting this procedure, drain engine oil completely. 1) Remove the intake manifold. 2)
Toyota Truck Tacoma Extra Cab 2WD L4-2.4L (2RZ-FE) Timing Chain: Service and Repair
Toyota Truck Tacoma Extra Cab 2WD L4-2.4L (2RZ-FE) 2002 Timing Chain: Service and Repair REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE OIL 3. 4 WD: REMOVE FRONT DIFFERENTIAL AND DRIVE SHAFTS
OVERHAUL 3. REMOVE EXHAUST VALVE
OVERHUL ENGINE MECHNICL CYLINDER HED SSY (2UZFE) HINT: Thoroughly clean all parts to be assembled. efore installing the parts, apply new engine oil to all sliding and rotating surfaces. Replace all gaskets,
2/17/2017 Timing Belt Service and Repair, Removal and Replacement
http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com 1/22 http://repair.alldata.com/alldata/article/display.action?componentid=64&itypeid=401&nonstandardid=0&vehicleid=39554&miles=&printfriendly=com
Page 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components
Page 1 of 25 Service and Repair REMOVAL Related Components Page 2 of 25 1ZZ-FE Page 3 of 25 2ZZ-GE 1. REMOVE UPPER FRONT FENDER APRON SEAL AND UPPER RADIATOR SUPPORT SEAL 2. DRAIN ENGINE COOLANT 3. REMOVE
2001 Toyota MR ENGINES' '1.8L 4-Cylinder
TIMING CHAIN Removal 1. Disconnect negative battery cable. Drain cooling system. On Corolla, remove windshield washer fluid reservoir. On Celica, remove upper front fender apron seal and upper radiator
FACILITY ACCREDITATION CHECKLIST R: 04/27/06 APPRENTICESHIP Designated Trade: Motor Vehicle Mechanic Level (circle one)
FACILITY ACCREDITATION CHECKLIST R: 04/27/06 APPRENTICESHIP Designated Trade: Level 1 2 3 (circle one) Institution: Evaluator(s) / / Rating Code: Y = Yes* N = No* R = Required * * Please use a CHECKMARK
1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION (2007 4Runner) Model Year: 2007 Model: 4Runner Doc ID: RM WS002X
Last Modified: 4-26-2007 Service Category: Engine/Hybrid System 1.6 A Section: Engine Mechanical Model Year: 2007 Model: 4Runner Doc ID: RM0000029WS002X Title: 1GR-FE ENGINE MECHANICAL: TIMING CHAIN: INSTALLATION
ENGINE MECHANICAL EM SECTION CONTENTS
ENGINE MECHANICAL EM SECTION CONTENTS INTAKE MANIFOLD...EM-2 Component Parts Location...EM-2 Removal and Installation...EM-3 Inspection...EM-3 EXHAUST MANIFOLD...EM-4 Component Parts Location...EM-4 Removal
Isuzu Truck Required Special Service Tool Inventory and New Dealer Set-Up Form
Please print or type clearly to avoid errors. Isuzu Truck Required Special Service Tool Inventory and New Dealer Set-Up Form 1. ed By: 2. Ship To: (ly if different than ordered by). Dealer Name Dealer
1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza
1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza ARTICLE BEGINNING 1995-98 ENGINES Subaru - 1.8L & 2.2L 4-Cylinder 1995-97: Impreza (1.8L) 1995-98: Impreza (2.2L), Legacy (2.2L) * PLEASE READ THIS FIRST
11. REMOVE OIL PAN SUB ASSY NO.2 (a) Remove the 18 bolts and 2 nuts.
1444 ENGINE MECHANICAL REPLACEMENT 1. REMOVE ENGINE ASSEMBLY (SEE PAGE 1419) 2. REMOVE DRIVE PLATE & RING GEAR SUBASSY (AUTOMATIC TRANSMISSION) (SEE PAGE 1419) SST 0921354015 (9165160855), 0933000021 3.
Front Differential Growl/Howl/Rumble Noise at MPH
T-SB-0121-08 Rev1 June 30, 2008 Service Category Drivetrain Section Axle/Differential Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2007 2008 Tundra Body Type(s): Double Cab, Crew Max,
2001 Dodge Dakota ENGINES 4.7L V8
FRONT COVER Removal & Installation 1. Disconnect negative battery cable. Remove drive belt. Remove A/C compressor mounting bolts, and position compressor aside. Drain cooling system. Remove radiator hoses.
2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.
TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right
5. SEPARATE STEERING INTERMEDIATE SHAFT ASSY (a) Fix the steering wheel with the seat belt. Release the 3 springs and separate the dust cover.
5119 OVERHAUL When installing, coat the parts indicated by the arrows with power steering fluid or molybdenum disulfide lithium base grease (See page 5116). 1. INSPECT CENTER FRONT WHEEL 510DA02 2. REMOVE
SST Storage System Master Index
SST Storage System Master Index JANUARY 2018 To Order Special Service Tools Call Bosch/OTC at 1-800-933-8335 Table of Contents Page # Part Number References......................................... 2-8
VALVE CLEARANCE (3ZZ FE/4ZZ FE)
ENGINE MECHANICAL ADJUSTMENT 1. REMOVE CYLINDER HEAD COVER NO.2 1487 140M901 Remove the 2 nuts, 2 clips and cylinder head cover. 2. REMOVE IGNITION COIL ASSY Disconnect the 4 connectors. (b) Remove the
2004 Essential Tool Survey Order Form
2004 Essential Tool Survey Order Form Page 1 Instructions for completing the 2004 Lexus Essential Tool Survey 1. Call each dealer at least a week in advance to schedule a date and time to perform the 2004
DF 43 DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY REMOVAL
DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY 43 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE REAR WHEEL 3. DRAIN BRAKE FLUID 4. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (See page
5. Cylinder Block. 2-3b [W5A1] SERVICE PROCEDURE A: REMOVAL 1. RELATED PARTS
![5. Cylinder Block. 2-3b [W5A1] SERVICE PROCEDURE A: REMOVAL 1. RELATED PARTS](/thumbs/82/85637729.jpg "5. Cylinder Block. 2-3b [W5A1] SERVICE PROCEDURE A: REMOVAL 1. RELATED PARTS")
2-3b [W5A1] SERVICE PROCEDURE A: REMOVAL 1. RELATED PARTS 1) Remove timing belt, camshaft sprockets and related parts. S2M0303 48 SERVICE PROCEDURE [W5A1] 2-3b 2) Remove rocker cover,
DIFFERENTIAL CASE COMPONENTS MX 99 E350 MANUAL TRANSAXLE DIFFERENTIAL CASE FRONT DIFFERENTIAL PINION THRUST WASHER
DIFFERENTIAL CASE TRANSMISSION E350 MANUAL TRANSAXLE COMPONENTS 99 THRUST WASHER FRONT NO. 1 DIFFERENTIAL SIDE GEAR THRUST WASHER FRONT DIFFERENTIAL SIDE GEAR FRONT DIFFERENTIAL SIDE GEAR FRONT NO. 1 DIFFERENTIAL
MD MB MD MB MITSUBISHI DRAWER #1 MITSUBISHI DRAWER #1 MD MD MD MIT47026 MD
MB992226 SERRATION SOCKET Drawer 1 A10 10/13 MD998716-01 CRANKSHAFT WRENCH Drawer 1 D1 10/13 MB991636-01 REDUCTION BRAKE ADJUSTER - STOPPER Drawer 1 A9 10/13 MD998364-01 CAMSHAFT OIL SEAL Drawer 1 A8 10/13
6. Cylinder Block SERVICE PROCEDURE A: REMOVAL 1. RELATED PARTS
SERVICE PROCEDURE [W6A1] 2-3a A: REMOVAL 1. RELATED PARTS 1) Remove timing belt, camshaft sprockets and related parts. 2) Remove cylinder heads. 3) Remove
ENGINE OVERHAUL GROUP 11B 11B-1 CONTENTS GENERAL SPECIFICATIONS... 11B-2 OIL PAN AND TIMING CHAIN CASE... 11B-27 SERVICE SPECIFICATIONS...
11B-1 GROUP 11B CONTENTS GENERAL SPECIFICATIONS 11B-2 SERVICE SPECIFICATIONS 11B-2 FASTENER TIGHTENING SPECIFICATIONS 11B-4 SEALANTS AND ADHESIVES 11B-7 SPECIAL TOOLS 11B-8 GENERATOR AND IGNITION SYSTEM
OIL AND FILTER INSPECTION
F 20 C 29 Recommended Viscosity (SAE): 0 18 20 7 5W30 40 4 60 16 80 27 LUBRICATION (2UZFE) 100 38 TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE B16233 OIL AND FILTER OIL AND FILTER INSPECTION 1.
Fig. 6: Assembling Piston & Rod. NOTE: Notch must face forward Toyota Starlet CRANKSHAFT MAIN BEARINGS
connecting rods are marked for reassembly. 3. Thoroughly clean and inspect all components. Coat pin with engine oil and heat piston to 158-176 F (70-80 C). Pin should push fit with thumb pressure through
Page 1 of 44 REPLACEMENT 1. 2. 3. 4. REMOVE ENGINE UNDER COVER RH DRAIN COOLANT (See REPLACEMENT ) REMOVE FRONT WHEEL RH REMOVE CYLINDER HEAD COVER NO. 2 a. Remove the 2 nuts, 2 clips and cylinder head
Removing and installing cylinder head
31 30 29 28 27 26 25 24 23 22 1 2 3 11 12 10 4 9 5 6 7 8 Removing and installing cylinder head Checking compression pressure page 15-24. Notes: When installing a replacement cylinder head with a mounted
Part Name. TOYOTA electrical tester. Engine sling device. Crankshaft pulley replacer. Belt tension gage. Connecting rod bushing remover & replacer
16-2 SST LIST Illustration Part No. Part Name Section : Newly adopted SST 1 2 4 5 6 7 8 11 12 13 14 15 09082-76002-71 (09082-00050) TOYOTA electrical tester 09090-76002-71 (09090-04020) Engine sling device
1. General Description
1. General Description A: SPECIFICATION 1. MANUAL TRANSMISSION AND FRONT DIFFERENTIAL Type Transmission gear ratio Front reduction gear Rear reduction gear Front differential Center differential Final
OVERHAUL. 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance.
41135 OVERHAUL 4108901 1. INSPECT 1ST GEAR THRUST CLEARANCE (a) Using a feeler gauge, measure the 1st gear thrust clearance. 0.10 0.40 mm (0.0039 0.0157 in.) C68252 2. INSPECT 2ND GEAR THRUST CLEARANCE
CAMSHAFT (LH BANK) (2GR FE) ENGINE MECHANICAL 1424N 01 REPLACEMENT
REPLACEMENT N0. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (SEE PAGE ). REMOVE ENGINE WIRE 3. REMOVE FRONT FRAME ASSY (SEE PAGE ). REMOVE STARTER ASSY (SEE PAGE 99). REMOVE AUTOMATIC TRANSAXLE ASSY (SEE PAGE
REAR AXLE AND SUSPENSION RA 1
REAR AXLE AND SUSPENSION RA1 RA2 REAR AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated Replace tires or inflate to
2.4L 4-CYL - VINS [F,H,S]
![2.4L 4-CYL - VINS [F,H,S]](/thumbs/72/66412829.jpg "2.4L 4-CYL - VINS [F,H,S]")
2.4L 4-CYL - VINS [F,H,S] 1990 Nissan 240SX 1990 ENGINES Nissan 2.4L 4-Cylinder Axxess, Pickup, Stanza, 240SX * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article,
ENGINE OVERHAUL <2.4L ENGINE>
11B-1 GROUP 11B ENGINE OVERHAUL CONTENTS GENERAL SPECIFICATIONS 11B-2 SERVICE SPECIFICATIONS 11B-2 REWORK DIMENSIONS 11B-3 TORQUE SPECIFICATIONS 11B-4 SEALANTS 11B-7 SPECIAL TOOLS 11B-8 GENERATOR
26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) Fax: (03) INSTALLATION MANUAL. for
26 Hume Reserve Court, Nth. Geelong, 3215 Phone: (03) 5272 2844 Fax: (03) 5272 2633 GEARLESS CENTRE DIFFERENTIAL FULL-TIME 4X4 TRANSFER CASE CONVERSION DEDICATED LOW RANGE INSTALLATION MANUAL for TOYOTA
EM-81 EM0Z7-01 DISASSEMBLY
EM81 EM0Z701 DISASSEMBLY 1. M/T: REMOVE FLYWHEEL 2. A/T: REMOVE DRIVE PLATE 3. REMOVE REAR END PLATE 4. INSTALL ENGINE TO ENGINE STAND FOR DIS ASSEMBLY 5. REMOVE TIMING BELT AND PULLEYS (See page EM13
ENGINE MECHANICAL <4G69>
11E-1 GROUP 11E ENGINE MECHANICAL CONTENTS SERVICE SPECIFICATIONS....... 11E-2 SEALANTS.................... 11E-2 SPECIAL TOOLS................ 11E-3 ON-VEHICLE SERVICE........... 11E-7 DRIVE BELT
Output Shaft Assembly COMPONENTS
MT140 Component Parts (Output Shaft Assembly Output Shaft Assembly COMPONENTS DISASSEMBLY OF OUTPUT SHAFT ASSEMBLY 1. REMOVE SLEEVE FROM OUTPUT SHAFT Using SST, remove the sleeve from the output shaft.
2.0L 4-CYL & 2.0L 4-CYL TURBO - VIN [S]
![2.0L 4-CYL & 2.0L 4-CYL TURBO - VIN [S]](/thumbs/81/82864711.jpg "2.0L 4-CYL & 2.0L 4-CYL TURBO - VIN [S]")
2.0L 4-CYL & 2.0L 4-CYL TURBO - VIN [S] 1988 Toyota Celica 1988 TOYOTA ENGINES 2.0L & 2.0L Turbo 4-Cylinder Celica * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article,
REMOVE FRONT WHEEL RH
518 OVERHAUL POWER STEERING Do not overtighten when using a vise. When installing, coat the parts indicated by the arrows with power steering fluid (see page 517 ). 1. REMOVE FRONT WHEEL RH 2. DRAIN POWER
MASTER CYLINDER INSPECTION
7-16 CHASSIS A-PDF Split DEMO : Purchase from www.a-pdf.com to remove the watermark Remove the piston assembly. MASTER CYLINDER INSPECTION MASTER CYLINDER Inspect the master cylinder bore for any scratches
ENGINE CONTENTS CAUTION
ENGINE CONTENTS ENGINE REMOVAL AND REINSTALLATION 3- ENGINE REMOVAL 3- ENGINE REINSTALLATION 3-7 ENGINE DISASSEMBLY 3-9 STARTER MOTER 3-9 THERMOSTAT 3-9 ND AIR VALVE 3-0 CYLINDER HEAD COVER 3-0 PISTON
MANUAL TRANSMISSION MUA 5C (4X2, 4X4) AND TREMEC T5R(4X2)
MANUAL TRANSMISSION 7B 1 RODEO TRANSMISSION MANUAL TRANSMISSION MUA 5C (4X2, 4X4) AND TREMEC T5R(4X2) CONTENTS Service Precaution...................... 7B 2 General Description..................... 7B