EU INTERREG CEREEV. Fuel Spray and Mixture Preparation in Split- Cycle Engine

Size: px
Start display at page:

Download "EU INTERREG CEREEV. Fuel Spray and Mixture Preparation in Split- Cycle Engine"

Transcription

1 EU INTERREG CEREEV Fuel Spray and Mixture Preparation in Split- Cycle Engine By Larissa R Taylor The Sir Harry Ricardo Laboratories-Centre for Automotive Engineering University of Brighton, UK September 2013

2 Computational Fluid Dynamics (CFD) model for engine cylinder and valves is taken from 2-ACE project: A fundamental study of the novel poppet valve 2-stroke auto ignition combustion engine EP/F058276/1

3 New concept of split-cycle engine:

4 New concept of split-cycle engine: modelling processes in expander cylinder

5 For CEREEV project, the CFD model for ANSYS FLUENT simulation includes modifications to Inlet and exhaust valve timings Injector location and its type Comparison of various breakup models Boundary conditions (pressure from compression cylinder)

6 Intake valve opened: Compressed Air 10bar Exhaust valve closed

7 Direct Injection of RON95 fuel spray 95% iso-octane 5% n-heptane Mass flowrate is kg/s Injection velocity = 200m/s What is the optimal injector location for mixture preparation to produce the fuel vapour cloud near the spark plug?

8 This depends on the flow pattern for guiding fuel vapour. The transient flow in expander cylinder is calculated.

9 Exploring three injector locations: Near spark plug Near inlet valve Near outlet duct

10 Near inlet valve Mass Fraction of Octane No-break up 10

11 Near inlet valve Mass Fraction of Octane TAB break up 11

12 Near inlet valve Mass Fraction of Octane Wave break up 12

13 New position of injector: Near inlet valve 13

14 Group injectors near exhaust valve MFR of each = kg/s 14

15 Near exhaust duct Mass Fraction of Octane No-break up 15

16 Near exhaust duct Mass Fraction of Octane Wave break up 16

17 New injector location: near spark plug 17

18 Near spark plug Mass Fraction of Octane No-break up 18

19 Injector near spark plug Mass Fraction of Octane vapour for WAVE break up model 0.16ms 19

20 0.2ms 20

21 0.3ms 21

22 0.4ms 22

23 1.2ms 23

24 1.8ms 24

25 Conclusions For the direct injection near the inlet valve, and near the exhaust duct, all CFD models showed that the fuel vapour was formed too far from the spark plug Some of the vapour is lost to the inlet duct due to reflected pressure waves. Closing the inlet valve could overcome this Exploring various flow patterns to guide the fuel spray is a key issue for a successful combustion

26 Conclusions The injector near the spark plug showed the fuel spray to overshoot and vapour be formed on the piston for the nobreak up CFD model The WAVE break up model showed the vapour to evaporate almost immediately in the vicinity of the spark plug Breakup spray model is a more realistic model to what would happen inside an engine. Thus having injector near spark plug would give a more successful combustion

27 Conclusions Further research is needed to be done to explore realistic flow patterns and injection strategies by CFD and experimental methods. But at this stage of development. What is the optimal injector location for mixture preparation near spark plug?

28 Near the Spark Plug 28

29 EU INTERREG CEREEV Fuel Spray and Mixture Preparation in Split- Cycle Engine By Larissa R Taylor The Sir Harry Ricardo Laboratories-Centre for Automotive Engineering University of Brighton, UK September 2013

30 Supervisors for the project: Dr Steve Begg Dr Elena Sazhina Consultants: Dr Oyuna Rybdylova Dr Daniel Coren 30

31 Contribution of EU INTERREG CEREEV team is gratefully acknowledged 31

32 Many thanks to the tutors at Park College Sussex Downs 32

33 Acknowledgements: Special thanks to STEM Sussex staff Daniel Hawkins Bronagh Liddicoat Patricia Harwood Financial help of the Nuffield Research Placement grant is gratefully acknowledged 33

34 Thank you Larissa R Taylor Park College Sussex Downs Eastbourne The Sir Harry Ricardo Laboratories Centre for Automotive Engineering

Fuel Spray and Mixture Preparation in Split-Cycle Engine A Nuffield Project with STEM Sussex

Fuel Spray and Mixture Preparation in Split-Cycle Engine A Nuffield Project with STEM Sussex Fuel Spray and Mixture Preparation in Split-Cycle Engine A Nuffield Project with STEM Sussex Larissa R Taylor Park College Sussex Downs Eastbourne Supervisors; Dr Steve Begg Dr Oyuna Rybdylova Dr Elena

More information

Mechanical Engineering Design of a Split-Cycle Combustor. Experimental Fluid-Mechanics Research Group

Mechanical Engineering Design of a Split-Cycle Combustor. Experimental Fluid-Mechanics Research Group Mechanical Engineering Design of a Split-Cycle Combustor Dr Daniel D Coren Dr Nicolas D D Miché Experimental Fluid-Mechanics Research Group University of Brighton, March 2015 mechanical design considerations

More information

Simulation of the Mixture Preparation for an SI Engine using Multi-Component Fuels

Simulation of the Mixture Preparation for an SI Engine using Multi-Component Fuels ICE Workshop, STAR Global Conference 2012 March 19-21 2012, Amsterdam Simulation of the Mixture Preparation for an SI Engine using Multi-Component Fuels Michael Heiss, Thomas Lauer Content Introduction

More information

Gas exchange and fuel-air mixing simulations in a turbocharged gasoline engine with high compression ratio and VVA system

Gas exchange and fuel-air mixing simulations in a turbocharged gasoline engine with high compression ratio and VVA system Third Two-Day Meeting on Internal Combustion Engine Simulations Using the OpenFOAM technology, Milan 22 nd -23 rd February 2018. Gas exchange and fuel-air mixing simulations in a turbocharged gasoline

More information

Validation and Verification of ANSYS Internal Combustion Engine Software. Martin Kuntz, ANSYS, Inc.

Validation and Verification of ANSYS Internal Combustion Engine Software. Martin Kuntz, ANSYS, Inc. Validation and Verification of ANSYS Internal Combustion Engine Software Martin Kuntz, ANSYS, Inc. Contents Definitions Internal Combustion Engines Demonstration example Validation & verification Spray

More information

L34: Internal Combustion Engine Cycles: Otto, Diesel, and Dual or Gas Power Cycles Introduction to Gas Cycles Definitions

L34: Internal Combustion Engine Cycles: Otto, Diesel, and Dual or Gas Power Cycles Introduction to Gas Cycles Definitions Page L: Internal Combustion Engine Cycles: Otto, Diesel, and Dual or Gas Power Cycles Review of Carnot Power Cycle (gas version) Air-Standard Cycles Internal Combustion (IC) Engines - Otto and Diesel Cycles

More information

Modeling Constant Volume Chamber Combustion at Diesel Engine Condition

Modeling Constant Volume Chamber Combustion at Diesel Engine Condition Modeling Constant Volume Chamber Combustion at Diesel Engine Condition Z. Hu, R.Cracknell*, L.M.T. Somers Combustion Technology Department of Mechanical Engineering Eindhoven University of Technology *Shell

More information

INFLUENCE OF THE NUMBER OF NOZZLE HOLES ON THE UNBURNED FUEL IN DIESEL ENGINE

INFLUENCE OF THE NUMBER OF NOZZLE HOLES ON THE UNBURNED FUEL IN DIESEL ENGINE INFLUENCE OF THE NUMBER OF NOZZLE HOLES ON THE UNBURNED FUEL IN DIESEL ENGINE 1. UNIVERSITY OF RUSE, 8, STUDENTSKA STR., 7017 RUSE, BULGARIA 1. Simeon ILIEV ABSTRACT: The objective of this paper is to

More information

Whither Diesel? An Overview of Combustion Concepts and Research Directions for Compression Ignition Engines

Whither Diesel? An Overview of Combustion Concepts and Research Directions for Compression Ignition Engines An Overview of Combustion Concepts and Research Directions for Compression Ignition Engines Martin H. University of Oxford, UK FPC2015 Future Powertrain Conference National Motorcycle Museum, Solihull

More information

COMBUSTION AND EXHAUST EMISSION IN COMPRESSION IGNITION ENGINES WITH DUAL- FUEL SYSTEM

COMBUSTION AND EXHAUST EMISSION IN COMPRESSION IGNITION ENGINES WITH DUAL- FUEL SYSTEM COMBUSTION AND EXHAUST EMISSION IN COMPRESSION IGNITION ENGINES WITH DUAL- FUEL SYSTEM WLADYSLAW MITIANIEC CRACOW UNIVERSITY OF TECHNOLOGY ENGINE-EXPO 2008 OPEN TECHNOLOGY FORUM STUTTGAT, 7 MAY 2008 APPLICATIONS

More information

Effect of Reformer Gas on HCCI Combustion- Part II: Low Octane Fuels

Effect of Reformer Gas on HCCI Combustion- Part II: Low Octane Fuels Effect of Reformer Gas on HCCI Combustion- Part II: Low Octane Fuels Vahid Hosseini, and M David Checkel Mechanical Engineering University of Alberta, Edmonton, Canada project supported by Auto21 National

More information

Engine Transient Characteristics Simulation Technology using Zero-dimensional Combustion Model

Engine Transient Characteristics Simulation Technology using Zero-dimensional Combustion Model 25 Engine Transient Characteristics Simulation Technology using Zero-dimensional Combustion Model TAKAYUKI YAMAMOTO *1 KENJI HIRAOKA *2 NAOYUKI MORI *2 YUJI ODA *3 AKIHIRO YUUKI *4 KENICHI ISONO *5 The

More information

Development of a two-dimensional internal combustion engines model using CFD for education purpose

Development of a two-dimensional internal combustion engines model using CFD for education purpose 20th International Congress on Modelling and Simulation, Adelaide, Australia, 1 6 December 2013 www.mssanz.org.au/modsim2013 Development of a two-dimensional internal combustion engines model using CFD

More information

POSIBILITIES TO IMPROVED HOMOGENEOUS CHARGE IN INTERNAL COMBUSTION ENGINES, USING C.F.D. PROGRAM

POSIBILITIES TO IMPROVED HOMOGENEOUS CHARGE IN INTERNAL COMBUSTION ENGINES, USING C.F.D. PROGRAM POSIBILITIES TO IMPROVED HOMOGENEOUS CHARGE IN INTERNAL COMBUSTION ENGINES, USING C.F.D. PROGRAM Alexandru-Bogdan Muntean *, Anghel,Chiru, Ruxandra-Cristina (Dica) Stanescu, Cristian Soimaru Transilvania

More information

Influence of Fuel Injector Position of Port-fuel Injection Retrofit-kit to the Performances of Small Gasoline Engine

Influence of Fuel Injector Position of Port-fuel Injection Retrofit-kit to the Performances of Small Gasoline Engine Influence of Fuel Injector Position of Port-fuel Injection Retrofit-kit to the Performances of Small Gasoline Engine M. F. Hushim a,*, A. J. Alimin a, L. A. Rashid a and M. F. Chamari a a Automotive Research

More information

Study of intake manifold for Universiti Malaysia Perlis automotive racing team formula student race car

Study of intake manifold for Universiti Malaysia Perlis automotive racing team formula student race car Journal of Physics: Conference Series PAPER OPEN ACCESS Study of intake manifold for Universiti Malaysia Perlis automotive racing team formula student race car To cite this article: A Norizan et al 2017

More information

PVRC Capabilities & Current Research

PVRC Capabilities & Current Research Department of Mechanical Engineering Powertrain & Vehicle Research Centre PVRC Capabilities & Current Research University of Bath 2 University of Bath South West England Primarily Engineering and Science

More information

COMPARISON OF BREAKUP MODELS IN SIMULATION OF SPRAY DEVELOPMENT IN DIRECT INJECTION SI ENGINE

COMPARISON OF BREAKUP MODELS IN SIMULATION OF SPRAY DEVELOPMENT IN DIRECT INJECTION SI ENGINE Journal of KONES Powertrain and Transport, Vol. 17, No. 4 2010 COMPARISON OF BREAKUP MODELS IN SIMULATION OF SPRAY DEVELOPMENT IN DIRECT INJECTION SI ENGINE Przemys aw wikowski, Piotr Jaworski, Andrzej

More information

System Simulation for Aftertreatment. LES for Engines

System Simulation for Aftertreatment. LES for Engines System Simulation for Aftertreatment LES for Engines Christopher Rutland Engine Research Center University of Wisconsin-Madison Acknowledgements General Motors Research & Development Caterpillar, Inc.

More information

Split Injection for CNG Engines

Split Injection for CNG Engines Willkommen Welcome Bienvenue Split Injection for CNG Engines Patrik Soltic, Hannes Biffiger Empa, Automotive Powertrain Technologies Laboratory Motivation CNG engines are gaining on importance in the stationary

More information

Task 4: Read the texts, look at the illustrations and do the activities below.

Task 4: Read the texts, look at the illustrations and do the activities below. Task 4: Read the texts, look at the illustrations and do the activities below. 4 BASIC OPERATIONS The Induction Stroke On the induction stroke, the inlet valve opens and the piston, moving down, creates

More information

Smoke Reduction Methods Using Shallow-Dish Combustion Chamber in an HSDI Common-Rail Diesel Engine

Smoke Reduction Methods Using Shallow-Dish Combustion Chamber in an HSDI Common-Rail Diesel Engine Special Issue Challenges in Realizing Clean High-Performance Diesel Engines 17 Research Report Smoke Reduction Methods Using Shallow-Dish Combustion Chamber in an HSDI Common-Rail Diesel Engine Yoshihiro

More information

[Rohith, 5(1): January, 2016] ISSN: (I2OR), Publication Impact Factor: 3.785

[Rohith, 5(1): January, 2016] ISSN: (I2OR), Publication Impact Factor: 3.785 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY COMPARING DIFFERENT VALVE LIFTS IN AN IC ENGINE USING COLD FLOW SIMULATION Rohith S, Dr G V Naveen Prakash Mechanical Engineering,

More information

Comparison of Swirl, Turbulence Generating Devices in Compression ignition Engine

Comparison of Swirl, Turbulence Generating Devices in Compression ignition Engine Available online atwww.scholarsresearchlibrary.com Archives of Applied Science Research, 2016, 8 (7):31-40 (http://scholarsresearchlibrary.com/archive.html) ISSN 0975-508X CODEN (USA) AASRC9 Comparison

More information

Investigation of Fuel Flow Velocity on CNG Engine using New Injector

Investigation of Fuel Flow Velocity on CNG Engine using New Injector Investigation of Fuel Flow Velocity on CNG Engine using New Injector Hari Prastowo 1, Semin 1*, M. Badrus Zaman 1, Amiadji 1, T. Bambang Musrijadi 1, Agoes Santoso 1, Dwi Priyanta 1, Sardono Sarwito 1,

More information

2. Air Line AIR LINE FUEL INJECTION (FUEL SYSTEM) A: GENERAL B: MANIFOLD ABSOLUTE PRESSURE SENSOR FU(H4DOTC)-3

2. Air Line AIR LINE FUEL INJECTION (FUEL SYSTEM) A: GENERAL B: MANIFOLD ABSOLUTE PRESSURE SENSOR FU(H4DOTC)-3 W1860BE.book Page 3 Tuesday, January 28, 2003 11:01 PM 2. Air Line A: GENERAL The air filtered by the air cleaner enters the throttle body where it is regulated in the volume by the throttle valve and

More information

The influence of fuel injection pump malfunctions of a marine 4-stroke Diesel engine on composition of exhaust gases

The influence of fuel injection pump malfunctions of a marine 4-stroke Diesel engine on composition of exhaust gases Article citation info: LEWIŃSKA, J. The influence of fuel injection pump malfunctions of a marine 4-stroke Diesel engine on composition of exhaust gases. Combustion Engines. 2016, 167(4), 53-57. doi:10.19206/ce-2016-405

More information

Numerical Study on the Combustion and Emission Characteristics of Different Biodiesel Fuel Feedstocks and Blends Using OpenFOAM

Numerical Study on the Combustion and Emission Characteristics of Different Biodiesel Fuel Feedstocks and Blends Using OpenFOAM Numerical Study on the Combustion and Emission Characteristics of Different Biodiesel Fuel Feedstocks and Blends Using OpenFOAM Harun M. Ismail 1, Xinwei Cheng 1, Hoon Kiat Ng 1, Suyin Gan 1 and Tommaso

More information

Crankcase scavenging.

Crankcase scavenging. Software for engine simulation and optimization www.diesel-rk.bmstu.ru The full cycle thermodynamic engine simulation software DIESEL-RK is designed for simulating and optimizing working processes of two-

More information

Proposal to establish a laboratory for combustion studies

Proposal to establish a laboratory for combustion studies Proposal to establish a laboratory for combustion studies Jayr de Amorim Filho Brazilian Bioethanol Science and Technology Laboratory SCRE Single Cylinder Research Engine Laboratory OUTLINE Requirements,

More information

INTERCOOLER FOR EXTREMELY LOW TEMPERATURES OF CHARGING

INTERCOOLER FOR EXTREMELY LOW TEMPERATURES OF CHARGING Journal of KONES Powertrain and Transport, Vol. 7, No. 4 200 INTERCOOLER FOR EXTREMELY LOW TEMPERATURES OF CHARGING Emil Toporcer, Peter Tunik University of Žilina, Faculty of Mechanical Engineering Department

More information

University of Huddersfield Repository

University of Huddersfield Repository University of Huddersfield Repository Stetsyuk, V., Crua, C., Pearson, R. and Gold, M. Direct imaging of primary atomisation in the near-nozzle region of diesel sprays Original Citation Stetsyuk, V., Crua,

More information

Foundations of Thermodynamics and Chemistry. 1 Introduction Preface Model-Building Simulation... 5 References...

Foundations of Thermodynamics and Chemistry. 1 Introduction Preface Model-Building Simulation... 5 References... Contents Part I Foundations of Thermodynamics and Chemistry 1 Introduction... 3 1.1 Preface.... 3 1.2 Model-Building... 3 1.3 Simulation... 5 References..... 8 2 Reciprocating Engines... 9 2.1 Energy Conversion...

More information

COMPRESSIBLE FLOW ANALYSIS IN A CLUTCH PISTON CHAMBER

COMPRESSIBLE FLOW ANALYSIS IN A CLUTCH PISTON CHAMBER COMPRESSIBLE FLOW ANALYSIS IN A CLUTCH PISTON CHAMBER Masaru SHIMADA*, Hideharu YAMAMOTO* * Hardware System Development Department, R&D Division JATCO Ltd 7-1, Imaizumi, Fuji City, Shizuoka, 417-8585 Japan

More information

DLR s Free Piston Linear Generator FPLG Development of an Innovative Linear Power Unit

DLR s Free Piston Linear Generator FPLG Development of an Innovative Linear Power Unit DLR s Free Piston Linear Generator FPLG of an Innovative Linear Power Unit Florian Kock September 8, 2015 www.dlr.de Slide 1 > Kock > FKLG > 2015-09-08 FPLG Project Overview A Decade of Linear Power 2002

More information

EFFECT OF INJECTION ORIENTATION ON EXHAUST EMISSIONS IN A DI DIESEL ENGINE: THROUGH CFD SIMULATION

EFFECT OF INJECTION ORIENTATION ON EXHAUST EMISSIONS IN A DI DIESEL ENGINE: THROUGH CFD SIMULATION EFFECT OF INJECTION ORIENTATION ON EXHAUST EMISSIONS IN A DI DIESEL ENGINE: THROUGH CFD SIMULATION *P. Manoj Kumar 1, V. Pandurangadu 2, V.V. Pratibha Bharathi 3 and V.V. Naga Deepthi 4 1 Department of

More information

Flow Simulation of Diesel Engine for Prolate Combustion Chamber

Flow Simulation of Diesel Engine for Prolate Combustion Chamber IJIRST National Conference on Recent Advancements in Mechanical Engineering (RAME 17) March 2017 Flow Simulation of Diesel Engine for Prolate Combustion Chamber R.Krishnakumar 1 P.Duraimurugan 2 M.Magudeswaran

More information

Determination of a turbocharged gasoline engine for hybrid powertrains. F. Kercher,

Determination of a turbocharged gasoline engine for hybrid powertrains. F. Kercher, Determination of a turbocharged gasoline engine for hybrid powertrains F. Kercher, 26.10.2015 Determination of a turbocharged gasoline engine for hybrid powertrains Agenda Introduction Hybrid Electric

More information

Numerical Investigation of the Effect of Excess Air and Thermal Power Variation in a Liquid Fuelled Boiler

Numerical Investigation of the Effect of Excess Air and Thermal Power Variation in a Liquid Fuelled Boiler Proceedings of the World Congress on Momentum, Heat and Mass Transfer (MHMT 16) Prague, Czech Republic April 4 5, 2016 Paper No. CSP 105 DOI: 10.11159/csp16.105 Numerical Investigation of the Effect of

More information

The Effect of Volume Ratio of Ethanol Directly Injected in a Gasoline Port Injection Spark Ignition Engine

The Effect of Volume Ratio of Ethanol Directly Injected in a Gasoline Port Injection Spark Ignition Engine 10 th ASPACC July 19 22, 2015 Beijing, China The Effect of Volume Ratio of Ethanol Directly Injected in a Gasoline Port Injection Spark Ignition Engine Yuhan Huang a,b, Guang Hong a, Ronghua Huang b. a

More information

Combustion Systems What we might have learned

Combustion Systems What we might have learned Combustion Systems What we might have learned IMechE ADSC, 6 December 2012 Chris Whelan Contents Engines Big & Small Carnot, Otto & Diesel Thermodynamic Cycles Combustion Process & Systems Diesel & Otto

More information

[Rao, 4(7): July, 2015] ISSN: (I2OR), Publication Impact Factor: 3.785

[Rao, 4(7): July, 2015] ISSN: (I2OR), Publication Impact Factor: 3.785 IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY CFD ANALYSIS OF GAS COOLER FOR ASSORTED DESIGN PARAMETERS B Nageswara Rao * & K Vijaya Kumar Reddy * Head of Mechanical Department,

More information

CFD Investigation of Influence of Tube Bundle Cross-Section over Pressure Drop and Heat Transfer Rate

CFD Investigation of Influence of Tube Bundle Cross-Section over Pressure Drop and Heat Transfer Rate CFD Investigation of Influence of Tube Bundle Cross-Section over Pressure Drop and Heat Transfer Rate Sandeep M, U Sathishkumar Abstract In this paper, a study of different cross section bundle arrangements

More information

Module7:Advanced Combustion Systems and Alternative Powerplants Lecture 32:Stratified Charge Engines

Module7:Advanced Combustion Systems and Alternative Powerplants Lecture 32:Stratified Charge Engines ADVANCED COMBUSTION SYSTEMS AND ALTERNATIVE POWERPLANTS The Lecture Contains: DIRECT INJECTION STRATIFIED CHARGE (DISC) ENGINES Historical Overview Potential Advantages of DISC Engines DISC Engine Combustion

More information

INTERNAL COMBUSTION ENGINE (SKMM 4413)

INTERNAL COMBUSTION ENGINE (SKMM 4413) INTERNAL COMBUSTION ENGINE (SKMM 4413) Dr. Mohd Farid bin Muhamad Said Room : Block P21, Level 1, Automotive Development Centre (ADC) Tel : 07-5535449 Email: mfarid@fkm.utm.my HISTORY OF ICE History of

More information

Ignition- and combustion concepts for lean operated passenger car natural gas engines

Ignition- and combustion concepts for lean operated passenger car natural gas engines Ignition- and combustion concepts for lean operated passenger car natural gas engines Patrik Soltic 1, Thomas Hilfiker 1 Severin Hänggi 2, Richard Hutter 2 1 Empa, Automotive Powertrain Technologies Laboratory,

More information

HERCULES-2 Project. Deliverable: D8.8

HERCULES-2 Project. Deliverable: D8.8 HERCULES-2 Project Fuel Flexible, Near Zero Emissions, Adaptive Performance Marine Engine Deliverable: D8.8 Study an alternative urea decomposition and mixer / SCR configuration and / or study in extended

More information

The effect of ethanolled gasoline on the performance and gaseous and particulate emissions on a 2/4-stroke switchable DI engine Yan Zhang & Hua Zhao

The effect of ethanolled gasoline on the performance and gaseous and particulate emissions on a 2/4-stroke switchable DI engine Yan Zhang & Hua Zhao The effect of ethanolled gasoline on the performance and gaseous and particulate emissions on a 2/4-stroke switchable DI engine Yan Zhang & Hua Zhao Centre for Advanced Powertrain and Fuels (CAPF) Brunel

More information

Direct Injection Ethanol Boosted Gasoline Engines: Biofuel Leveraging For Cost Effective Reduction of Oil Dependence and CO 2 Emissions

Direct Injection Ethanol Boosted Gasoline Engines: Biofuel Leveraging For Cost Effective Reduction of Oil Dependence and CO 2 Emissions Direct Injection Ethanol Boosted Gasoline Engines: Biofuel Leveraging For Cost Effective Reduction of Oil Dependence and CO 2 Emissions D.R. Cohn* L. Bromberg* J.B. Heywood Massachusetts Institute of Technology

More information

Influence of ANSYS FLUENT on Gas Engine Modeling

Influence of ANSYS FLUENT on Gas Engine Modeling Influence of ANSYS FLUENT on Gas Engine Modeling George Martinas, Ovidiu Sorin Cupsa 1, Nicolae Buzbuchi, Andreea Arsenie 2 1 CERONAV 2 Constanta Maritime University Romania georgemartinas@ceronav.ro,

More information

INFLUENCE OF THE MARINE 4-STROKE DIESEL ENGINE MALFUNCTIONS ON THE NITRIC OXIDES EMISSION

INFLUENCE OF THE MARINE 4-STROKE DIESEL ENGINE MALFUNCTIONS ON THE NITRIC OXIDES EMISSION Journal of KONES Powertrain and Transport, Vol. 20, No. 1 2013 INFLUENCE OF THE MARINE 4-STROKE DIESEL ENGINE MALFUNCTIONS ON THE NITRIC OXIDES EMISSION Joanna Lewi ska Gdynia Maritime University Morska

More information

INTAKE VALVE LIFT EFFECT ON AIR-FUEL MIXING OF DUAL FUEL ENGINE

INTAKE VALVE LIFT EFFECT ON AIR-FUEL MIXING OF DUAL FUEL ENGINE International Journal of Mechanical Engineering and Technology (IJMET) Volume 10, Issue 2, February 2019, pp; 1301-1318 Article ID: IJMET_10_02_136 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=10&itype=2

More information

Motor Vehicle Engineering

Motor Vehicle Engineering Motor Vehicle Engineering 25 It deals with the design and maintenance of a motor vehicle and its accessories. The main courses in this stream are: IC Engine & Reciprocating Machine Motor Vehicle Engineering

More information

Recent Advances in DI-Diesel Combustion Modeling in AVL FIRE A Validation Study

Recent Advances in DI-Diesel Combustion Modeling in AVL FIRE A Validation Study International Multidimensional Engine Modeling User s Group Meeting at the SAE Congress April 15, 2007 Detroit, MI Recent Advances in DI-Diesel Combustion Modeling in AVL FIRE A Validation Study R. Tatschl,

More information

A Study of EGR Stratification in an Engine Cylinder

A Study of EGR Stratification in an Engine Cylinder A Study of EGR Stratification in an Engine Cylinder Bassem Ramadan Kettering University ABSTRACT One strategy to decrease the amount of oxides of nitrogen formed and emitted from certain combustion devices,

More information

Increasing Low Speed Engine Response of a Downsized CI Engine Equipped with a Twin-Entry Turbocharger

Increasing Low Speed Engine Response of a Downsized CI Engine Equipped with a Twin-Entry Turbocharger Increasing Low Speed Engine Response of a Downsized CI Engine Equipped with a Twin-Entry Turbocharger A. Kusztelan, Y. F. Yao, D. Marchant and Y. Wang Benefits of a Turbocharger Increases the volumetric

More information

Comparative Study Of Four Stroke Diesel And Petrol Engine.

Comparative Study Of Four Stroke Diesel And Petrol Engine. Comparative Study Of Four Stroke Diesel And Petrol Engine. Aim: To study the construction and working of 4- stroke petrol / diesel engine. Theory: A machine or device which derives heat from the combustion

More information

Single-Cylinder Research Engines

Single-Cylinder Research Engines Single-Cylinder Research Engines Combustion research and mechanical testing of engine parts for diesel, gasoline and alternative fuels Hydra Standard and custom engine designs for light-duty applications

More information

THE INFLUENCE OF THE EGR RATE ON A HCCI ENGINE MODEL CALCULATED WITH THE SINGLE ZONE HCCI METHOD

THE INFLUENCE OF THE EGR RATE ON A HCCI ENGINE MODEL CALCULATED WITH THE SINGLE ZONE HCCI METHOD CONAT243 THE INFLUENCE OF THE EGR RATE ON A HCCI ENGINE MODEL CALCULATED WITH THE SINGLE ZONE HCCI METHOD KEYWORDS HCCI, EGR, heat release rate Radu Cosgarea *, Corneliu Cofaru, Mihai Aleonte Transilvania

More information

Technologies for Clean Engines Future Power Train 2019

Technologies for Clean Engines Future Power Train 2019 Technologies for Clean Engines Future Power Train 2019 February 2019 Professor Robert Morgan Joint Secretary of UnICEG Deputy Head of the AEC Scope of presentation 2 What I won t do - make a case for the

More information

AN ANALYSIS OF EFFECT OF VARIABLE COMPRESSION RATIO IN C.I. ENGINE USING TURBOCHARGER

AN ANALYSIS OF EFFECT OF VARIABLE COMPRESSION RATIO IN C.I. ENGINE USING TURBOCHARGER AN ANALYSIS OF EFFECT OF VARIABLE COMPRESSION RATIO IN C.I. ENGINE USING TURBOCHARGER E.Saravanapprabhu 1, M.Mahendran 2 1E.Saravanapprabhu, PG Student, Thermal Engineering, Department of Mechanical Engineering,

More information

Analytical Tool Development for Aftertreatment Sub-Systems Integration

Analytical Tool Development for Aftertreatment Sub-Systems Integration Analytical Tool Development for Aftertreatment Sub-Systems Integration B. Bolton, A. Fan, K. Goney, Z. Pavlova-MacKinnon, K. Sisken, H. Zhang Detroit Diesel Corporation Engine and Sub-System Integration

More information

Porsche Engineering driving technologies

Porsche Engineering driving technologies European GT-Suite User Conference 2016 Frankfurt am Main, 17. Oktober 2016 Real Drive Efficiency Improvement in turbocharged Engines by the use of Expansion Intake Manifold Content > Introduction Motivation

More information

Experimental Investigation of Acceleration Test in Spark Ignition Engine

Experimental Investigation of Acceleration Test in Spark Ignition Engine Experimental Investigation of Acceleration Test in Spark Ignition Engine M. F. Tantawy Basic and Applied Science Department. College of Engineering and Technology, Arab Academy for Science, Technology

More information

The Rotating Cylinder Valve 4-stroke 4 A Practical Alternative. Keith Lawes

The Rotating Cylinder Valve 4-stroke 4 A Practical Alternative. Keith Lawes The Rotating Cylinder Valve 4-stroke 4 Engine A Practical Alternative Keith Lawes RCV Engines Limited - UK 1 The Rotating Cylinder Valve 4-Stroke A Practical Alternative 4-stroke emissions 2-stroke performance

More information

Overview & Perspectives for Internal Combustion Engine using STAR-CD. Marc ZELLAT

Overview & Perspectives for Internal Combustion Engine using STAR-CD. Marc ZELLAT Overview & Perspectives for Internal Combustion Engine using STAR-CD Marc ZELLAT TOPICS Quick overview of ECFM family models Examples of validation for Diesel and SI-GDI engines Introduction to multi-component

More information

Homogeneous Charge Compression Ignition combustion and fuel composition

Homogeneous Charge Compression Ignition combustion and fuel composition Loughborough University Institutional Repository Homogeneous Charge Compression Ignition combustion and fuel composition This item was submitted to Loughborough University's Institutional Repository by

More information

Emissions predictions for Diesel engines based on chemistry tabulation

Emissions predictions for Diesel engines based on chemistry tabulation Emissions predictions for Diesel engines based on chemistry tabulation C. Meijer, F.A. Tap AVL Dacolt BV (The Netherlands) M. Tvrdojevic, P. Priesching AVL List GmbH (Austria) 1. Introduction It is generally

More information

Design and Development Of Opposite Piston Engine

Design and Development Of Opposite Piston Engine ISSN (Online) : 2319-8753 ISSN (Print) : 2347-6710 International Journal of Innovative Research in Science, Engineering and Technology Volume 3, Special Issue 3, March 2014 2014 IEEE International Conference

More information

Port Fuel Injection (PFI) Strategies for Lean Burn in Small Capacity Spark Ignition Engines

Port Fuel Injection (PFI) Strategies for Lean Burn in Small Capacity Spark Ignition Engines ISSN 2395-1621 Port Fuel Injection (PFI) Strategies for Lean Burn in Small Capacity Spark Ignition Engines #1 Shailendra Patil, #2 Santosh Trimbake 1 shailendrapatil7592@gmail.com 2 santoshtrimbake@yahoo.co.in

More information

NZQA Expiring unit standard 3400 version 4 Page 1 of 6. Check a four stroke petrol engine for condition using hand held test equipment

NZQA Expiring unit standard 3400 version 4 Page 1 of 6. Check a four stroke petrol engine for condition using hand held test equipment Page 1 of 6 Title Check a four stroke petrol engine for condition using hand held test equipment Level 3 Credits 4 Purpose This unit standard is for people in the automotive repair industry. People credited

More information

CONTROLLING COMBUSTION IN HCCI DIESEL ENGINES

CONTROLLING COMBUSTION IN HCCI DIESEL ENGINES CONTROLLING COMBUSTION IN HCCI DIESEL ENGINES Nicolae Ispas *, Mircea Năstăsoiu, Mihai Dogariu Transilvania University of Brasov KEYWORDS HCCI, Diesel Engine, controlling, air-fuel mixing combustion ABSTRACT

More information

Virtual Flow Bench Test of a Two Stroke Engine

Virtual Flow Bench Test of a Two Stroke Engine Virtual Flow Bench Test of a Two Stroke Engine Preformed by: Andrew Sugden University of Wisconsin Platteville Mechanical Engineering ME: 4560, John Iselin 01.05.2011 Introduction: As an undergraduate

More information

EFFECTS OF LOCAL AND GENERAL EXHAUST VENTILATION ON CONTROL OF CONTAMINANTS

EFFECTS OF LOCAL AND GENERAL EXHAUST VENTILATION ON CONTROL OF CONTAMINANTS Ventilation 1 EFFECTS OF LOCAL AND GENERAL EXHAUST VENTILATION ON CONTROL OF CONTAMINANTS A. Kelsey, R. Batt Health and Safety Laboratory, Buxton, UK British Crown copyright (1) Abstract Many industrial

More information

PM Emissions from HCCI Engines

PM Emissions from HCCI Engines PM Emissions from HCCI Engines H.M. Xu, J. Misztal, M.L. Wyszynski University of Birmingham P. Price, R. Stone Oxford University J. Qiao Jaguar Cars Particulate matter and measurement Cambridge University,

More information

Comparing FEM Transfer Matrix Simulated Compressor Plenum Pressure Pulsations to Measured Pressure Pulsations and to CFD Results

Comparing FEM Transfer Matrix Simulated Compressor Plenum Pressure Pulsations to Measured Pressure Pulsations and to CFD Results Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2012 Comparing FEM Transfer Matrix Simulated Compressor Plenum Pressure Pulsations to Measured

More information

PIEZO ELECTRIC CONTROL HYDRAULIC STACKS FOR THE CAMLESS ENGINE

PIEZO ELECTRIC CONTROL HYDRAULIC STACKS FOR THE CAMLESS ENGINE PIEZO ELECTRIC CONTROL HYDRAULIC STACKS FOR THE CAMLESS ENGINE PROJECT REFERENCE NO. : 37S0751 COLLEGE : BASAVAKALYAN ENGINEERING COLLEGE, BIDAR BRANCH : MECHANICAL ENGINEERING GUIDE : SANTOSH PATIL STUDENTS

More information

Improvement of Atomization Characteristics of Spray by Multi-Hole Nozzle for Pressure Atomized Type Injector

Improvement of Atomization Characteristics of Spray by Multi-Hole Nozzle for Pressure Atomized Type Injector , 23rd Annual Conference on Liquid Atomization and Spray Systems, Brno, Czech Republic, September 2010 Improvement of Atomization Characteristics of Spray by Multi-Hole Nozzle for Pressure Atomized Type

More information

Numerical Simulation of the Effect of 3D Needle Movement on Cavitation and Spray Formation in a Diesel Injector

Numerical Simulation of the Effect of 3D Needle Movement on Cavitation and Spray Formation in a Diesel Injector Journal of Physics: Conference Series PAPER OPEN ACCESS Numerical Simulation of the Effect of 3D Needle Movement on Cavitation and Spray Formation in a Diesel Injector To cite this article: B Mandumpala

More information

CFD Flow Analysis and Optimization of Exhaust Muffler

CFD Flow Analysis and Optimization of Exhaust Muffler CFD Flow Analysis and Optimization of Exhaust Muffler Saumil Mahesh Trivedi 1, Sangita Bansode 2, Pankaj Pawar 3 1 Mtech CAD-CAM & Robotics Student Somaiya college of engineering 2 Professor, Department

More information

Kul Internal Combustion Engine Technology. Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5

Kul Internal Combustion Engine Technology. Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5 Kul-14.4100 Internal Combustion Engine Technology Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5 Definitions Combustion engines convert the chemical energy of fuel to mechanical

More information

The Effects of Chamber Temperature and Pressure on a GDI Spray Characteristics in a Constant Volume Chamber

The Effects of Chamber Temperature and Pressure on a GDI Spray Characteristics in a Constant Volume Chamber 한국동력기계공학회지제18권제6호 pp. 186-192 2014년 12월 (ISSN 1226-7813) Journal of the Korean Society for Power System Engineering http://dx.doi.org/10.9726/kspse.2014.18.6.186 Vol. 18, No. 6, pp. 186-192, December 2014

More information

Reduction of Fuel Consumption and Emissions Electromechanical Valve Train in Vehicle Operation

Reduction of Fuel Consumption and Emissions Electromechanical Valve Train in Vehicle Operation Technology- H i g h l i g h t s a n d R & D A c t i v i t i e s a t F E V Issue 12 / Aug. 1999 Reduction of Fuel Consumption and Emissions Electromechanical Valve Train in Vehicle Operation FEV has proven

More information

COMPUTATIONAL FLOW MODEL OF WESTFALL'S 2900 MIXER TO BE USED BY CNRL FOR BITUMEN VISCOSITY CONTROL Report R0. By Kimbal A.

COMPUTATIONAL FLOW MODEL OF WESTFALL'S 2900 MIXER TO BE USED BY CNRL FOR BITUMEN VISCOSITY CONTROL Report R0. By Kimbal A. COMPUTATIONAL FLOW MODEL OF WESTFALL'S 2900 MIXER TO BE USED BY CNRL FOR BITUMEN VISCOSITY CONTROL Report 412509-1R0 By Kimbal A. Hall, PE Submitted to: WESTFALL MANUFACTURING COMPANY May 2012 ALDEN RESEARCH

More information

Finite Element Analysis on Thermal Effect of the Vehicle Engine

Finite Element Analysis on Thermal Effect of the Vehicle Engine Proceedings of MUCEET2009 Malaysian Technical Universities Conference on Engineering and Technology June 20~22, 2009, MS Garden, Kuantan, Pahang, Malaysia Finite Element Analysis on Thermal Effect of the

More information

IC Engines Roadmap. STAR-CD/es-ice v4.18 and Beyond. Richard Johns

IC Engines Roadmap. STAR-CD/es-ice v4.18 and Beyond. Richard Johns IC Engines Roadmap STAR-CD/es-ice v4.18 and Beyond Richard Johns Strategy es-ice v4.18 2D Automated Template Meshing Spray-adapted Meshing Physics STAR-CD v4.18 Contents Sprays: ELSA Spray-Wall Impingement

More information

B. von Rotz, A. Schmid, S. Hensel, K. Herrmann, K. Boulouchos. WinGD/PSI, 10/06/2016, CIMAC Congress 2016 / B. von Rotz

B. von Rotz, A. Schmid, S. Hensel, K. Herrmann, K. Boulouchos. WinGD/PSI, 10/06/2016, CIMAC Congress 2016 / B. von Rotz Comparative Investigation of Spray Formation, Ignition and Combustion for LFO and HFO at Conditions relevant for Large 2-Stroke Marine Diesel Engine Combustion Systems B. von Rotz, A. Schmid, S. Hensel,

More information

NUMERICAL INVESTIGATION OF EFFECT OF EXHAUST GAS RECIRCULATION ON COMPRESSIONIGNITION ENGINE EMISSIONS

NUMERICAL INVESTIGATION OF EFFECT OF EXHAUST GAS RECIRCULATION ON COMPRESSIONIGNITION ENGINE EMISSIONS ISSN (Online) : 2319-8753 ISSN (Print) : 2347-6710 International Journal of Innovative Research in Science, Engineering and Technology An ISO 3297: 2007 Certified Organization, Volume 2, Special Issue

More information

Chapter 14 Small Gas Engines

Chapter 14 Small Gas Engines Chapter 14 Small Gas Engines Use the Textbook Pages 321 349 to help answer the questions Why You Learn So Well in Tech & Engineering Classes 1. Internal combustion make heat by burning a fuel & air mixture

More information

Marc ZELLAT, Driss ABOURI, Thierry CONTE and Riyad HECHAICHI CD-adapco

Marc ZELLAT, Driss ABOURI, Thierry CONTE and Riyad HECHAICHI CD-adapco 16 th International Multidimensional Engine User s Meeting at the SAE Congress 2006,April,06,2006 Detroit, MI RECENT ADVANCES IN SI ENGINE MODELING: A NEW MODEL FOR SPARK AND KNOCK USING A DETAILED CHEMISTRY

More information

THE THEORETICAL STUDY ON INFLUENCE OF FUEL INJECTION PRESSURE ON COMBUSTION PARAMETERS OF THE MARINE 4-STROKE ENGINE

THE THEORETICAL STUDY ON INFLUENCE OF FUEL INJECTION PRESSURE ON COMBUSTION PARAMETERS OF THE MARINE 4-STROKE ENGINE Journal of KONES Powertrain and Transport, Vol. 23, No. 1 2016 THE THEORETICAL STUDY ON INFLUENCE OF FUEL INJECTION PRESSURE ON COMBUSTION PARAMETERS OF THE MARINE 4-STROKE ENGINE Jerzy Kowalski Gdynia

More information

Abstract 1. INTRODUCTION

Abstract 1. INTRODUCTION Abstract Study on Performance Characteristics of Scuderi Split Cycle Engine Sudeer Gowd Patil 1, Martin A.J. 2, Ananthesha 3 1- M.Sc. [Engg.] Student, 2-Asst. Professor, 3-Asst.Professor, Department of

More information

DISCHARGE AND FLOW COEFFICIENT ANALYSIS IN INTERNAL COMBUSTION ENGINE USING COMPUTATIONAL FLUID DYNAMICS SIMULATION

DISCHARGE AND FLOW COEFFICIENT ANALYSIS IN INTERNAL COMBUSTION ENGINE USING COMPUTATIONAL FLUID DYNAMICS SIMULATION DISCHARGE AND FLOW COEFFICIENT ANALYSIS IN INTERNAL COMBUSTION ENGINE USING COMPUTATIONAL FLUID DYNAMICS SIMULATION N. A. Mohamad Shafie 1, M. F. Muhamad Said 1, Z. Abdul Latiff 1 and S. Rajoo 2 1 Automotive

More information

Variable Intake Manifold Development trend and technology

Variable Intake Manifold Development trend and technology Variable Intake Manifold Development trend and technology Author Taehwan Kim Managed Programs LLC (tkim@managed-programs.com) Abstract The automotive air intake manifold has been playing a critical role

More information

Development of Low-Exergy-Loss, High-Efficiency Chemical Engines

Development of Low-Exergy-Loss, High-Efficiency Chemical Engines Development of Low-Exergy-Loss, High-Efficiency Chemical Engines Investigators C. F., Associate Professor, Mechanical Engineering; Kwee-Yan Teh, Shannon L. Miller, Graduate Researchers Introduction The

More information

IJSRD - International Journal for Scientific Research & Development Vol. 4, Issue 07, 2016 ISSN (online):

IJSRD - International Journal for Scientific Research & Development Vol. 4, Issue 07, 2016 ISSN (online): IJSRD - International Journal for Scientific Research & Development Vol. 4, Issue 07, 2016 ISSN (online): 2321-0613 Design, Optimization and Analysis of Exhaust Muffler to Reduce Exhaust Noise Level and

More information

Eco-diesel engine fuelled with rapeseed oil methyl ester and ethanol. Part 3: combustion processes

Eco-diesel engine fuelled with rapeseed oil methyl ester and ethanol. Part 3: combustion processes Eco-diesel engine fuelled with rapeseed oil methyl ester and ethanol. Part 3: combustion processes A Kowalewicz Technical University of Radom, al. Chrobrego 45, Radom, 26-600, Poland. email: andrzej.kowalewicz@pr.radom.pl

More information

Fuel Injection Systems in Diesel and SI Engines

Fuel Injection Systems in Diesel and SI Engines 1 Fuel Injection Systems in Diesel and SI Engines Kul-14.4700 Transport Biofuels, Combustion, and Emission Control 2015 D.Sc. (Tech) Ossi Kaario 2 Motivation Why learn about fuel injection systems? Fuel

More information

Timing is everything with internal combustion engines By: Bernie Thompson

Timing is everything with internal combustion engines By: Bernie Thompson Timing is everything with internal combustion engines By: Bernie Thompson As one goes through life, it is said that timing is everything. In the case of the internal combustion engine, this could not be

More information

Optical Techniques in Gasoline Engine Performance and Emissions Development Injector Spray Visualisation

Optical Techniques in Gasoline Engine Performance and Emissions Development Injector Spray Visualisation Injector Spray Visualisation Denis Gill, Wolfgang Krankenedl, DEC Ernst Winklhofer 20.03.15 Emissions Development Injector Spray Visualisation Contents Introduction Spray Box Direct Injection (GDI) Spray

More information