Assignment-1 Air Standard Cycles

Size: px
Start display at page:

Download "Assignment-1 Air Standard Cycles"

Transcription

1 Assignment-1 Air Standard Cycles 1. What do u mean by air standard cycle? List assumptions for air standard cycle & give reasons why air standard cycle differs from actual cycle. 2. Derive an equation of efficiency, work output and mean effective pressure for Otto cycle. 3. Derive an equation of efficiency, work output and mean effective pressure for Diesel cycle. 1. An engine working on Otto cycle has the following condition: Pressure at the beginning of compression is 1 bar and pressure at the end of compression is 11 bar. Calculate the compression ratio and air-standard efficiency of the engine. Assume γ = In an Otto cycle air at 17 and 1 bar is compressed adiabatically until the pressure is 15 bar. Heat is added at constant volume until the pressure rises to 40 bar. Calculate the airstandard efficiency, the compression ratio and the mean effective pressure for the cycle. Assume C p = kj/kgk and R = kj/kmol K. 3. In an S.I. engine working on the Otto cycle, compression ratio is 5.5. The pressure and temperature at the beginning of compression are 1 bar and 27 respectively. The peak pressure is 30 bar. Determine the pressure and temperature at the salient points, the air standard efficiency and mean effective pressure. Assume ratio of specific heats to be 1.4 for air. 4. A spark ignition engine working on ideal Otto cycle has the compression ratio 6. The initial pressure and temperature of air are 1 bar and 37. The maximum pressure in the cycle is 30 bar. For unit mass flow, calculate a. P, V and T at various salient points b. The ratio of heat supplied to heat rejected Assume γ = 1.4, R = kj/kmol K 5. A Diesel engine has a compression ratio of 20 and cut takes place at 5 % of the stroke. Find the air standard efficiency. Assume γ = In an engine working on Diesel cycle inlet pressure and temperature are 1 bar and 17 respectively. Pressure at the end of adiabatic compression is 35 bar. The ratio of expansion i.e. after constant pressure heat addition is 5. Calculate heat addition, heat rejection and efficiency of the cycle. Assume γ = 1.4, C p = kj/kgk and C p = kj/kgk. 7. The initial conditions for an air standard Diesel cycle operating with a compression ratio of 15:1 are 0.95 bar and 17. The heat added is 1800 kj/kg. Calculate the pressure and temperature at the end of each process of the cycle, also determine thermal efficiency and mean effective pressure of the cycle.

2 8. A compression ignition engine working on Diesel cycle operates at a compression ratio of 15 using Diesel oil of kj/kg. The inlet pressure and temperature are 1 bar and 300 K. The air-fuel ratio is 21. Calculate for air standard cycle a. The temperature and pressure at the salient points. b. The air standard efficiency and c. Mean effective pressure. Assignment-2 Fuel-Air Cycles 1. Enlist the assumptions which are made for fuel-air cycle analysis. 2. Explain the phenomenon of dissociation. Also explain its effect on maximum temperature and power. 3. Explain following: a. Burning time loss factor b. Heat loss factor c. Pumping and friction loss factor 1. What will be the effect of percentage change in the efficiency of Otto cycle having a compression ratio of 8, if the specific heat at constant volume increases by 1.1 percent? Ans: % 2. Calculate the percentage change in efficiency of air standard Otto cycle having a compression ratio of 7, if the specific heat at constant volume increases by 2 %. Ans: -1.32% 3. The following particulars relate to a Diesel cycle: Compression ratio = 18, cut-off = 5% of stroke, mean specific heat Cv for cycle = 0.71 kj/kg K, characteristic gas constant = kj/kg K. If the mean specific heat for the air standard cycle increases by 2% determine the percentage change in the air standard efficiency. Ans: % 4. What will be the effect on the efficiency of a diesel cycle having a compression ratio of 20 and a cut-off takes place at 8% of the swept volume, if the Cv increases by 1%. Take Cv = kj/kg K and R = kj/kg K. Ans: % 5. A petrol engine using a compression ratio 7 and air-fuel ratio of 15:1 has the pressure and temperature at the end of suction stroke as 1 bar and 57 C respectively. The fuel used has a calorific value of kj/kg. Compression follows the law specific heat at constant volume is given by the relation, C 1.33 pv constant and 4 V T, where T

3 is in Kelvin. Determine the maximum pressure and temperature in the cylinder and compare this value with that of constant specific heat, Cv = kj/kg K. Ans: (T = K & K, P = bar & bar) 6. A Diesel engine uses a compression ratio of 16 and at the end of compression the temperature of the air is 1100 K. Now the air is supplied at constant pressure by burning fuel of calorific value of kj/kg K and the fuel-air ratio is 0.04:1. Specific heat at constant volume T is given as: CV T where T is in Kelvin. Determine the maximum temperature in the cylinder and compare this value with that of constant specific heat, Cv = 0.72 kj/kg K. Ans: (T = K & K) 7. In an oil engine, working on dual combustion cycle the temperature and pressure et the beginning of compression are 87 C and 1 bar. The compression ratio is 14:1. The heat supplied per kg of air is 1700 kj, half of which is supplied at constant volume and half at constant pressure. Take Cv = X 10-4 T, where T is in Kelvin. Calculate (i) The maximum pressure in the cycle (ii) The percentage of stroke at which cut-off occurs. Ans: (i) bar (ii) 2.42 % Assignment-3 Combustion 1. Explain construction and working of Junker s gas calorimeter with neat sketch. Assignment-4 Fuel supply system for SI and CI engine 1. Explain with neat sketch working Simple Carburettor. Also explain Drawback and application of simple Carburettor. 2. With neat sketch explain working principle and constructional detail of Bosch fuel injection pump. 3. Describe different types of injection nozzles and discuss their relative advantages and disadvantages. 4. What is the function of carburetor? What is carburetion 1. A petrol engine consumes 7.5 kg of petrol per hour. The specific gravity of the fuel is The air temperature is 25 C. The air fuel ratio is 15. The choke tube has a diameter of 22 mm. Calculate the diameter of the fuel jet of a simple carburetor. Top of the jet is 4 mm above the petrol level in the float chamber. Take coefficient of discharge as 0.82 and 0.7 for air and fuel respectively. Atmospheric pressure = bar.

4 2. The venture of a simple carburetor has a throat diameter of 20 mm and the coefficient of air flow is The fuel orifice has a diameter of 1.25 mm and the coefficient of fuel flow is The petrol surface is 5 mm below the throat. Find a) the air-fuel ratio for a pressure drop of 0.07 bar when the nozzle lip is neglected; b) the air-fuel ratio when the nozzle lip is taken into account; c) the minimum velocity of air or critical air velocity required to start the fuel flow when nozzle lip is provided. Take density of air and fuel as 1.2 and 750 kg/m 3 respectively. Assignment-5 Ignition and Governing System 1. Explain Ignition Requirement. Explain the working of battery ignition system. State its advantages and disadvantages over magneto ignition system. 2. Describe a high tension magneto ignition system and compare its advantages and disadvantages with a coil ignition system. 3. State the various methods of governing of IC engines and discuss any one of them. Assignment 6 Supercharging 1. Define Supercharging And Give Its Advantage And Disadvantage. Give Limitation Of Supercharging. 2. Which are the supercharging limitation for SI engine and CI engine? 3. Explain method of supercharging. 4. What do you mean by turbo charging? Write advantage and limitation of turbo charging. Assignment-7 Combustion in SI and CI Engines 1. What do you understand by knock in S.I. Engines? Explain this phenomenon? How does the knock in S.I. Engines differ from the knock in C.I. Engines? 2. Explain with neat sketch Combustion stages in S. I. Engine. Also define Auto ignition Temperature. 3. What are basic requirements of good spark ignition engine combustion chamber and general principles of spark ignition combustion chamber 4. Explain the phenomenon of diesel knock. Compare it with the phenomenon of detonation in SI engine. Assignment-8 Engine Lubrication and Cooling 1. Explain with neat sketch splash lubrication system. 2. What are the different methods of cooling I.C. engine? Compare different methods.

5 Assignment-9 Measurement and Testing of IC engines 1. Explain the Methods of obtaining Friction Power and explain any one of them in details. 2. Explain the importance of engine testing. Example 1. In a Morse test with four cylinder four stroke petrol engine, the following data were obtained for a particular setting and speed. Brake power with all cylinders working = 32.0 Brake power with no. 1 cylinder cut out = 21.6 Brake power with no. 2 cylinder cut out = 22.3 Brake power with no. 3 cylinder cut out = 22.5 Brake power with no. 4 cylinder cut out = 23.0 Estimate the indicated power of the engine and its mechanical efficiency. 2. A 4-cylinder, 4-stroke petrol engine 6 cm bore and 9 cm stroke was tested at constant speed. The fuel supply was fixed to 0.13 kg/min and plugs of 4-cylinders were successively short-circuited without change of speed. The power measurements were as follows: With all cylinder working=16.25 kw With No.1st cylinder cut-off=11.55 kw With No.2nd cylinder cut-off =11.65 kw (BP) With No.3rd cylinder cut-off =11.70 kw (BP) With No.4th cylinder cut-off =11.50 kw (BP) Find (a) The IP of engine (b) Mechanical efficiency (c) Indicated thermal efficiency if CV of fuel used is kj/kg and (d) Find the relative efficiency on IP bases assuming clearance vol. =60 cm 3 3. The following observations were recorded from test on a single cylinder four stroke oil engine cylinder bore =150mm, engine stroke =250mm engine speed 420rpm, brake torque=217nm, fuel consumption 2.95 kg/h, calorific value of fuel=44000kj/kg cooling Assignment-10 Engine Emission and their control 1. Write brief notes on: Euro Norms and Testing of IC engine as per IS. 2. What are the major pollutants from the exhaust of gasoline &diesel engines? What are the detrimental effects of these pollutants? 3. Write down Bharat Stages of emission norms in brief for cars and two wheelers. 4. Explain different methods of measurement of pollutants in exhaust gases.

Assignment-1 Introduction

Assignment-1 Introduction Assignment-1 Introduction 1. Compare S.I. engines with C.I engines. 2. Explain with the help of neat sketch, the working of a 2-stroke petrol engine. 3. Derive an equation of efficiency, work output and

More information

2013 THERMAL ENGINEERING-I

2013 THERMAL ENGINEERING-I SET - 1 II B. Tech II Semester, Regular Examinations, April/May 2013 THERMAL ENGINEERING-I (Com. to ME, AME) Time: 3 hours Max. Marks: 75 Answer any FIVE Questions All Questions carry Equal Marks ~~~~~~~~~~~~~~~~~~~~~~~~

More information

AT AUTOMOTIVE ENGINES QUESTION BANK

AT AUTOMOTIVE ENGINES QUESTION BANK AT6301 - AUTOMOTIVE ENGINES QUESTION BANK UNIT I: CONSTRUCTION & WORKING PRINCIPLE OF IC ENGINES 1. State the application of CI engines? 2. What is Cubic capacity of an engine? 3. What is the purpose of

More information

SET - 1 II B. Tech II Semester Regular/Supplementary Examinations, April/May-2017 THERMAL ENGINEERING-I (Mechanical Engineering) Time: 3 hours Max. Marks: 70 Note: 1. Question Paper consists of two parts

More information

2. Discuss the effects of the following operating variables on detonation

2. Discuss the effects of the following operating variables on detonation Code No: RR220303 Set No. 1 II B.Tech II Semester Regular Examinations, Apr/May 2006 THERMAL ENGINEERING-I ( Common to Mechanical Engineering and Automobile Engineering) Time: 3 hours Max Marks: 80 Answer

More information

Scheme - G. Sample Test Paper-I. Course Name : Diploma in Mechanical Engineering Course Code : ME Semester : Fifth Subject Title : Power Engineering

Scheme - G. Sample Test Paper-I. Course Name : Diploma in Mechanical Engineering Course Code : ME Semester : Fifth Subject Title : Power Engineering Sample Test Paper-I Marks : 25 Time:1 hour Q1. Attempt any Three 3X3=9 a) Define i) Mean Effective Pressure ii) Piston Speed iii) Swept Volume b) Draw Carnot cycle on P-V and T-S Diagram c) State the need

More information

Noble Group of Institutions, Junagadh. Faculty of Engineering Department of Mechanical Engineering

Noble Group of Institutions, Junagadh. Faculty of Engineering Department of Mechanical Engineering Semester:1 st Subject: Elements of Mechanical Engineering (2110006) Faculty: Mr. Ishan Bhatt Year: 2017-18 Class: Comp. & IT Ele TUTORIAL 1 INTRODUCTION Q.1 Define: Force, Work, Pressure, Energy, Heat

More information

SIDDHARTH INSTITUTE OF ENGINEERING & TECHNOLOGY :: PUTTUR (AUTONOMOUS) QUESTION BANK UNIT I I.C ENGINES

SIDDHARTH INSTITUTE OF ENGINEERING & TECHNOLOGY :: PUTTUR (AUTONOMOUS) QUESTION BANK UNIT I I.C ENGINES SIDDHARTH INSTITUTE OF ENGINEERING & TECHNOLOGY :: PUTTUR UNIT I I.C ENGINES 1 (a) Explain any six types of classification of Internal Combustion engines. (6M) (b) With a neat sketch explain any three

More information

B.Tech. - VIEP - MECHANICAL ENGINEERING (BTMEVI) Term-End Examination June 2016

B.Tech. - VIEP - MECHANICAL ENGINEERING (BTMEVI) Term-End Examination June 2016 No. of Printed Pages : 5 I BIME-010 I B.Tech. - VIEP - MECHANICAL ENGINEERING (BTMEVI) 00 1 Ems, Term-End Examination June 2016 BIME-010 : THERMAL ENGINEERING Time : 3 hours Maximum Marks : 70 Note : Attempt

More information

(a) then mean effective pressure and the indicated power for each end ; (b) the total indicated power : [16]

(a) then mean effective pressure and the indicated power for each end ; (b) the total indicated power : [16] Code No: R05220304 Set No. 1 II B.Tech II Semester Regular Examinations, Apr/May 2007 THERMAL ENGINEERING-I ( Common to Mechanical Engineering and Automobile Engineering) Time: 3 hours Max Marks: 80 Answer

More information

MEB THERMAL ENGINEERING - I QUESTION BANK UNIT-I PART-A

MEB THERMAL ENGINEERING - I QUESTION BANK UNIT-I PART-A MEB 420 - THERMAL ENGINEERING - I QUESTION BANK UNIT-I Each question carries 1 mark. PART-A 1. Define temperature. 2. Define intensive property 3. Explain the term absolute zero of temperature 4. State

More information

ME2301 THERMAL ENGINEERING L T P C OBJECTIVE:

ME2301 THERMAL ENGINEERING L T P C OBJECTIVE: ME2301 THERMAL ENGINEERING L T P C 3 1 0 4 OBJECTIVE: To integrate the concepts, laws and methodologies from the first course in thermo dynamics into analysis of cyclic processes To apply the thermodynamic

More information

ME Thermal Engineering Question Bank

ME Thermal Engineering Question Bank ME2301 - Thermal Engineering Question Bank UNIT I GAS POWER CYCLES Otto, Diesel, Dual, Brayton cycles, Calculation of mean effective pressure, and air standard efficiency -Actual and theoretical PV diagram

More information

KINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING. Question Bank. UNIT-I THERMODYNAMIC CYCLES Part-A (2 Marks)

KINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING. Question Bank. UNIT-I THERMODYNAMIC CYCLES Part-A (2 Marks) KINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING Question Bank Sub. Code/Name: ME1351 - THERMAL ENGINEERING Year/Sem: III/VI 1. What is a thermodynamic cycle? UNIT-I THERMODYNAMIC CYCLES

More information

GYANMANJARI INSTITUTE OF TECHNOLOGY (GMIT) SUBJECT: ELEMENTS OF MECHANICAL ENGINEERING Assignment Ch 1

GYANMANJARI INSTITUTE OF TECHNOLOGY (GMIT) SUBJECT: ELEMENTS OF MECHANICAL ENGINEERING Assignment Ch 1 1. 3. GYANMANJARI INSTITUTE OF TECHNOLOGY (GMIT) Assignment Ch 1 A steel ball having mass of 10 kg and a specific heat of 460 J/kg K is heated from 50 o C to 200 o C. Determine the heat required. In a

More information

Please welcome for any correction or misprint in the entire manuscript and your valuable suggestions kindly mail us

Please welcome for any correction or misprint in the entire manuscript and your valuable suggestions kindly mail us Problems of Practices Of Basic and Applied Thermodynamics I. C. Engine Prepared By Brij Bhooshan Asst. Professor B. S. A. College of Engg. And Technology Mathura, Uttar Pradesh, (India) Supported By: Purvi

More information

VETRI VINAYAHA COLLEGE OF ENGINEERING AND TECHNOLOGY DEPARTMENT OF MECHANICAL ENGINEERING ME6404 THERMAL ENGINEERING

VETRI VINAYAHA COLLEGE OF ENGINEERING AND TECHNOLOGY DEPARTMENT OF MECHANICAL ENGINEERING ME6404 THERMAL ENGINEERING VETRI VINAYAHA COLLEGE OF ENGINEERING AND TECHNOLOGY DEPARTMENT OF MECHANICAL ENGINEERING ME6404 THERMAL ENGINEERING UNIT I - GAS POWER CYCLES 1. What is a thermodynamic cycle? Thermodynamic cycle is defined

More information

Internal Combustion Engines TUTORIAL

Internal Combustion Engines TUTORIAL Internal Combustion Engines TUTORIAL College of Engineering Mechanical Engineering Department Academic Year 2012-2013 Class 3 rd Year Class Subject Lecturer Internal Combustion Engines Dr. Raoof M. Radhi

More information

(v) Cylinder volume It is the volume of a gas inside the cylinder when the piston is at Bottom Dead Centre (B.D.C) and is denoted by V.

(v) Cylinder volume It is the volume of a gas inside the cylinder when the piston is at Bottom Dead Centre (B.D.C) and is denoted by V. UNIT II GAS POWER CYCLES AIR STANDARD CYCLES Air standard cycles are used for comparison of thermal efficiencies of I.C engines. Engines working with air standard cycles are known as air standard engines.

More information

Model Question Papers

Model Question Papers QUESTION CARRIES 2 MARKS Model Question Papers 1. Define engine. Give their classification? 6 th Semester I.C. ENGINE [ME-604] UNIT -1 2. Define the performance parameters of IC engine ie indicated power,

More information

Page 2. (a) (i) Show that during the change AB the gas undergoes an isothermal change.

Page 2. (a) (i) Show that during the change AB the gas undergoes an isothermal change. Q1.The Carnot cycle is the most efficient theoretical cycle of changes for a fixed mass of gas in a heat engine. The graph below shows the pressure volume (p V) diagram for a gas undergoing a Carnot cycle

More information

AT 2303 AUTOMOTIVE POLLUTION AND CONTROL Automobile Engineering Question Bank

AT 2303 AUTOMOTIVE POLLUTION AND CONTROL Automobile Engineering Question Bank AT 2303 AUTOMOTIVE POLLUTION AND CONTROL Automobile Engineering Question Bank UNIT I INTRODUCTION 1. What are the design considerations of a vehicle?(jun 2013) 2..Classify the various types of vehicles.

More information

VALVE TIMING DIAGRAM FOR SI ENGINE VALVE TIMING DIAGRAM FOR CI ENGINE

VALVE TIMING DIAGRAM FOR SI ENGINE VALVE TIMING DIAGRAM FOR CI ENGINE VALVE TIMING DIAGRAM FOR SI ENGINE VALVE TIMING DIAGRAM FOR CI ENGINE Page 1 of 13 EFFECT OF VALVE TIMING DIAGRAM ON VOLUMETRIC EFFICIENCY: Qu. 1:Why Inlet valve is closed after the Bottom Dead Centre

More information

DEPARTMENT OF MECHANICAL ENGINEERING Question Bank ME THERMAL ENGINEERING. Part-A (2 Marks)

DEPARTMENT OF MECHANICAL ENGINEERING Question Bank ME THERMAL ENGINEERING. Part-A (2 Marks) DEPARTMENT OF MECHANICAL ENGINEERING Question Bank ME1351 - THERMAL ENGINEERING UNIT I GAS POWER CYCLES Part-A (2 Marks) 1. What is a thermodynamic cycle? 2. What is meant by air standard cycle? 3.. Name

More information

SAMPLE STUDY MATERIAL

SAMPLE STUDY MATERIAL IC Engine - ME GATE, IES, PSU 1 SAMPLE STUDY MATERIAL Mechanical Engineering ME Postal Correspondence Course Internal Combustion Engine GATE, IES & PSUs IC Engine - ME GATE, IES, PSU 2 C O N T E N T 1.

More information

Engine Cycles. T Alrayyes

Engine Cycles. T Alrayyes Engine Cycles T Alrayyes Introduction The cycle experienced in the cylinder of an internal combustion engine is very complex. The cycle in SI and diesel engine were discussed in detail in the previous

More information

CHAPTER I GAS POWER CYCLES

CHAPTER I GAS POWER CYCLES CHAPTER I GAS POWER CYCLES 1.1 AIR STANDARD CYCLES Air standard cycles are used for comparison of thermal efficiencies of I.C engines. Engines working with air standard cycles are known as air standard

More information

Hours / 100 Marks Seat No.

Hours / 100 Marks Seat No. 17529 14115 3 Hours / 100 Seat No. Instructions (1) All Questions are Compulsory. (2) Answer each next main Question on a new page. (3) Illustrate your answers with neat sketches wherever necessary. (4)

More information

4. With a neat sketch explain in detail about the different types of fuel injection system used in SI engines. (May 2016)

4. With a neat sketch explain in detail about the different types of fuel injection system used in SI engines. (May 2016) SYED AMMAL ENGINEERING COLLEGE (Approved by the AICTE, New Delhi, Govt. of Tamilnadu and Affiliated to Anna University, Chennai) Established in 1998 - An ISO 9001:2000 Certified Institution Dr. E.M.Abdullah

More information

BASIC CIVIL & MECHANICAL ENGINEERING

BASIC CIVIL & MECHANICAL ENGINEERING SHRI ANGALAMMAN COLLEGE OF ENGINEERING AND TECHNOLOGY (An ISO 9001:2000 Certified Institution) SIRUGANOOR, TIRUCHIRAPPALLI 621 105 DEPARTMENT OF MECHANICAL ENGINEERING FS81504 BASIC CIVIL & MECHANICAL

More information

2.61 Internal Combustion Engine Final Examination. Open book. Note that Problems 1 &2 carry 20 points each; Problems 3 &4 carry 10 points each.

2.61 Internal Combustion Engine Final Examination. Open book. Note that Problems 1 &2 carry 20 points each; Problems 3 &4 carry 10 points each. 2.61 Internal Combustion Engine Final Examination Open book. Note that Problems 1 &2 carry 20 points each; Problems 3 &4 carry 10 points each. Problem 1 (20 points) Ethanol has been introduced as the bio-fuel

More information

COVENANT UNIVERSITY NIGERIA TUTORIAL KIT OMEGA SEMESTER PROGRAMME: MECHANICAL ENGINEERING

COVENANT UNIVERSITY NIGERIA TUTORIAL KIT OMEGA SEMESTER PROGRAMME: MECHANICAL ENGINEERING COVENANT UNIVERSITY NIGERIA TUTORIAL KIT OMEGA SEMESTER PROGRAMME: MECHANICAL ENGINEERING COURSE: MCE 320 DISCLAIMER The contents of this document are intended for practice and leaning purposes at the

More information

UNIT 2 POWER PLANTS 2.1 INTRODUCTION 2.2 CLASSIFICATION OF IC ENGINES. Objectives. Structure. 2.1 Introduction

UNIT 2 POWER PLANTS 2.1 INTRODUCTION 2.2 CLASSIFICATION OF IC ENGINES. Objectives. Structure. 2.1 Introduction UNIT 2 POWER PLANTS Power Plants Structure 2.1 Introduction Objectives 2.2 Classification of IC Engines 2.3 Four Stroke Engines versus Two Stroke Engines 2.4 Working of Four Stroke Petrol Engine 2.5 Working

More information

Internal Combustion Engine

Internal Combustion Engine Internal Combustion Engine 1. A 9-cylinder, 4-stroke cycle, radial SI engine operates at 900rpm. Calculate: (1) How often ignition occurs, in degrees of engine rev. (2) How many power strokes per rev.

More information

density ratio of 1.5.

density ratio of 1.5. Problem 1: An 8cyl 426 ci Hemi motor makes 426 HP at 5500 rpm on a compression ratio of 10.5:1. It is over square by 10% meaning that it s stroke is 10% less than it s bore. It s volumetric efficiency

More information

Internal Combustion Engine. Prepared by- Md Ferdous Alam Lecturer, MEE, SUST

Internal Combustion Engine. Prepared by- Md Ferdous Alam Lecturer, MEE, SUST Internal Combustion Engine Prepared by- Md Ferdous Alam Lecturer, MEE, SUST What is an Engine? -a machine designed to convert one form of energy into mechanical energy Two types of engines : 1. Internal

More information

L34: Internal Combustion Engine Cycles: Otto, Diesel, and Dual or Gas Power Cycles Introduction to Gas Cycles Definitions

L34: Internal Combustion Engine Cycles: Otto, Diesel, and Dual or Gas Power Cycles Introduction to Gas Cycles Definitions Page L: Internal Combustion Engine Cycles: Otto, Diesel, and Dual or Gas Power Cycles Review of Carnot Power Cycle (gas version) Air-Standard Cycles Internal Combustion (IC) Engines - Otto and Diesel Cycles

More information

GOVERNMENT ENGINEERING COLLEGE, GODHRA

GOVERNMENT ENGINEERING COLLEGE, GODHRA Practical No. - 1 To understand construction and working of various types of Steam boilers. 1) What is the function of Steam boiler? And what are factors should be considered while selecting a boiler?

More information

Combustion engines. Combustion

Combustion engines. Combustion Combustion engines Chemical energy in fuel converted to thermal energy by combustion or oxidation Heat engine converts chemical energy into mechanical energy Thermal energy raises temperature and pressure

More information

Department of Mechanical Engineering UBMC701 AUTOMOBILE ENGINEERING QUESTION BANK VEHICLE STRUCTURE AND ENGINES. Part A (Two Marks Questions)

Department of Mechanical Engineering UBMC701 AUTOMOBILE ENGINEERING QUESTION BANK VEHICLE STRUCTURE AND ENGINES. Part A (Two Marks Questions) Department of Mechanical Engineering UBMC701 AUTOMOBILE ENGINEERING QUESTION BANK UNIT- I VEHICLE STRUCTURE AND ENGINES 1. Define Automobile. Give the typical specifications of an automobile 2. Name the

More information

PART B - UNIT I - VEHICLE STRUCTURE AND ENGINES

PART B - UNIT I - VEHICLE STRUCTURE AND ENGINES BHARATHIDASAN ENGINEERING COLLEGE, NATTRAMPALLI 635854. DEPARTMENT OF MECHANICAL ENGINEERING ME 6602 AUTOMOBILE ENGINEERING FREQUENTLY ASKED QUESTIONS PART A - UNIT I - VEHICLE STRUCTURE AND ENGINES 1.

More information

SCHOOL OF COMPUTING, ENGINEERING AND MATHEMATICS SEMESTER 2 EXAMINATIONS 2013/2014 ME110. Aircraft and Automotive Systems

SCHOOL OF COMPUTING, ENGINEERING AND MATHEMATICS SEMESTER 2 EXAMINATIONS 2013/2014 ME110. Aircraft and Automotive Systems s SCHOOL OF COMPUTING, ENGINEERING AND MATHEMATICS SEMESTER 2 EXAMINATIONS 2013/2014 ME110 Aircraft and Automotive Systems Time allowed: TWO hours Answer TWO questions from THREE in Section A and TWO questions

More information

'' ''' '' ''' Code No: R R16 SET - 1

'' ''' '' ''' Code No: R R16 SET - 1 Code No: R161232 R16 SET - 1 1. a) List the Primary requirements of a Steam Boiler. (2M) b) What are the distinguishing features between a Casting and a Pattern? (2M) c) Define (i) Brake Power; (ii) Indicated

More information

ME 74 AUTOMOTIVE POLLUTION AND CONTROL Automobile Engineering-vii sem Question Bank( )

ME 74 AUTOMOTIVE POLLUTION AND CONTROL Automobile Engineering-vii sem Question Bank( ) ME 74 AUTOMOTIVE POLLUTION AND CONTROL Automobile Engineering-vii sem Question Bank(2013-2014) UNIT I INTRODUCTION 1. How the transient operation of S.I engine will cause CO formation? (may /June 2007)

More information

2.61 Internal Combustion Engines

2.61 Internal Combustion Engines Due: Thursday, February 19, 2004 2.61 Internal Combustion Engines Problem Set 2 Tuesday, February 10, 2004 1. Several velocities, time, and length scales are useful in understanding what goes on inside

More information

2) Rich mixture: A mixture which contains less air than the stoichiometric requirement is called a rich mixture (ex. A/F ratio: 12:1, 10:1 etc.

2) Rich mixture: A mixture which contains less air than the stoichiometric requirement is called a rich mixture (ex. A/F ratio: 12:1, 10:1 etc. Unit 3. Carburettor University Questions: 1. Describe with suitable sketches : Main metering system and Idling system 2. Draw the neat sketch of a simple carburettor and explain its working. What are the

More information

Prepared by: Dr. Assim Adaraje

Prepared by: Dr. Assim Adaraje Air-standard cycles Prepared by: Dr. Assim Adaraje CH. 2 ۱ Cold-air-standard assumptions: When the working fluid is considered to be air with constant specific heats at room temperature (25 C). Air-standard

More information

Class Notes on Thermal Energy Conversion System

Class Notes on Thermal Energy Conversion System Class Notes on Thermal Energy Conversion System For the students of Civil & Rural 3 rd semester Ramesh Khanal Assistant Professorr Nepal Engineering College Bhaktapur, Nepal 2015 Course Structure MEC 209.3:

More information

Content : 4.1 Brayton cycle-p.v. diagram and thermal efficiency. 4Marks Classification of gas turbines.

Content : 4.1 Brayton cycle-p.v. diagram and thermal efficiency. 4Marks Classification of gas turbines. Content : 4.1 Brayton cycle-p.v. diagram and thermal efficiency. 4Marks Classification of gas turbines. 4.2 Construction and working of gas turbines i) Open cycle ii) Closed cycle gas Turbines, P.V. and

More information

Simple Finite Heat Release Model (SI Engine)

Simple Finite Heat Release Model (SI Engine) Simple Finite Heat Release Model (SI Engine) Introduction In the following, a finite burn duration is taken into account, in which combustion occurs at θ soc (Start Of Combustion), and continues until

More information

UNIT IV INTERNAL COMBUSTION ENGINES

UNIT IV INTERNAL COMBUSTION ENGINES UNIT IV INTERNAL COMBUSTION ENGINES Objectives After the completion of this chapter, Students 1. To know the different parts of IC engines and their functions. 2. To understand the working principle of

More information

LABORATORY MANUAL I. C. ENGINES & GAS TURBINES (ME-317-E)

LABORATORY MANUAL I. C. ENGINES & GAS TURBINES (ME-317-E) LABORATORY MANUAL I. C. ENGINES & GAS TURBINES (ME-317-E) LIST OF EXPERIMENTS S.No. Name of the Experiment 1. To study the constructional details & working principles of two-stroke petrol/ four-stroke

More information

UNIT I GAS POWER CYCLES

UNIT I GAS POWER CYCLES UNIT I GAS POWER CYCLES The Otto Cycle The Otto cycle, which was first proposed by a Frenchman, Beau de Rochas in 1862, was first used on an engine built by a German, Nicholas A. Otto, in 1876. The cycle

More information

Heat Transfer in Engines. Internal Combustion Engines

Heat Transfer in Engines. Internal Combustion Engines Heat Transfer in Engines Internal Combustion Engines Energy Distribution Removing heat is critical in keeping an engine and lubricant from thermal failure Amount of energy available for use: Brake thermal

More information

Comparative Study Of Four Stroke Diesel And Petrol Engine.

Comparative Study Of Four Stroke Diesel And Petrol Engine. Comparative Study Of Four Stroke Diesel And Petrol Engine. Aim: To study the construction and working of 4- stroke petrol / diesel engine. Theory: A machine or device which derives heat from the combustion

More information

MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION (Autonomous) Summer 15 EXAMINATION Subject Code: Model Answer Page No: 1/18

MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION (Autonomous) Summer 15 EXAMINATION Subject Code: Model Answer Page No: 1/18 Subject Code: 708 Model Answer Page No: /8 Important Instructions to examiners: ) The answers should be examined by key words and not as word-to-word as given in the model answer scheme. ) The model answer

More information

1. (a) If a large power generating station is operating with steam at 16,000 kpa and 500 and exhausting to a condenser at, 37.6 mm mercury absolute;

1. (a) If a large power generating station is operating with steam at 16,000 kpa and 500 and exhausting to a condenser at, 37.6 mm mercury absolute; Sample Questions REVISED SECOND CLASS PARTS B1, B2, AND B3 (NOTE: these questions are intended as representations of the style of questions that may appear on examinations, they are not intended as study

More information

INTERNAL COMBUSTION ENGINES

INTERNAL COMBUSTION ENGINES Second Edition Fundamentals of INTERNAL COMBUSTION ENGINES Solenoid winding Electrical connection Pintle Valve needle Return spring H.N. Gupta FUNDAMENTALS OF INTERNAL COMBUSTION ENGINES SECOND EDITION

More information

Principles of Engine Operation. Information

Principles of Engine Operation. Information Internal Combustion Engines MAK 4070E Principles of Engine Operation Prof.Dr. Cem Soruşbay Istanbul Technical University Information Prof.Dr. Cem Soruşbay İ.T.Ü. Makina Fakültesi Motorlar ve Taşıtlar Laboratuvarı

More information

Internal Combustion Engines

Internal Combustion Engines Internal Combustion Engines Reading Problems 8-3 8-7 8-35, 8-45, 8-52 Definitions 1. spark ignition: a mixture of fuel and air is ignited by a spark plug applications requiring power to about 225 kw (300

More information

WINTER -14 EXAMINATION Subject Code: Model Answer Page No: 1/22

WINTER -14 EXAMINATION Subject Code: Model Answer Page No: 1/22 (ISO/IEC - 700-005 Certified) WINTER - EXAMINATION Subject Code: 708 Model Answer Page No: / Important Instructions to examiners: ) The answers should be examined by key words and not as word-to-word as

More information

I.C ENGINES. CLASSIFICATION I.C Engines are classified according to:

I.C ENGINES. CLASSIFICATION I.C Engines are classified according to: I.C ENGINES An internal combustion engine is most popularly known as I.C. engine, is a heat engine which converts the heat energy released by the combustion of the fuel taking place inside the engine cylinder

More information

Government of Karnataka Department of Technical Education Board of Technical Examinations, Bangalore

Government of Karnataka Department of Technical Education Board of Technical Examinations, Bangalore CIE- 25 Marks Government of Karnataka Department of Technical Education Board of Technical Examinations, Bangalore Prerequisites: Knowledge of basic mathematics and Applied Science Course Objectives: 1.

More information

05 Marks (c) Sketch and explain Lancashire Boiler.

05 Marks (c) Sketch and explain Lancashire Boiler. Model question paper No.1 1. Answer any FIVE full questions choosing at least two questions from part A & two questions from part B 2. Use of steam tables is permitted 1. (a) Discuss briefly the different

More information

SHRI SHANKARACHARYA INSTITUTE OF PROFESSIONAL MANAGEMENT AND TECHNOLOGY LAB MANUAL INTERNAL COMBUSTION ENGINES MECHANICAL ENGINEERING DEPARTMENT

SHRI SHANKARACHARYA INSTITUTE OF PROFESSIONAL MANAGEMENT AND TECHNOLOGY LAB MANUAL INTERNAL COMBUSTION ENGINES MECHANICAL ENGINEERING DEPARTMENT SHRI SHANKARACHARYA INSTITUTE OF PROFESSIONAL MANAGEMENT AND TECHNOLOGY LAB MANUAL INTERNAL COMBUSTION ENGINES MECHANICAL ENGINEERING DEPARTMENT LAB MANUAL INTERNAL COMBUSTION ENGINES 1. ) AIM : Study

More information

Internal Combustion Engines

Internal Combustion Engines Air and Fuel Induction Lecture 3 1 Outline In this lecture we will discuss the following: A/F mixture preparation in gasoline engines using carburetion. Air Charging technologies: Superchargers Turbochargers

More information

Simulation of Performance Parameters of Spark Ignition Engine for Various Ignition Timings

Simulation of Performance Parameters of Spark Ignition Engine for Various Ignition Timings Research Article International Journal of Current Engineering and Technology ISSN 2277-4106 2013 INPRESSCO. All Rights Reserved. Available at http://inpressco.com/category/ijcet Simulation of Performance

More information

Applied Thermodynamics Internal Combustion Engines

Applied Thermodynamics Internal Combustion Engines Applied Thermodynamics Internal Combustion Engines Assoc. Prof. Dr. Mazlan Abdul Wahid Faculty of Mechanical Engineering Universiti Teknologi Malaysia www.fkm.utm.my/~mazlan 1 Coverage Introduction Operation

More information

Important Instructions to examiners: 1) The answers should be examined by key words and not as word-to-word as given in the model answer scheme. 2) The model answer and the answer written by candidate

More information

UNIT 1 GAS POWER CYCLES

UNIT 1 GAS POWER CYCLES THERMAL ENGINEERING UNIT 1 GAS POWER CYCLES Air Standard Cycles - Otto, Diesel, Dual, Brayton cycle with intercooling, reheating and regeneration- Calculation of airstandard efficiency and mean effective

More information

Gas Power System. By Ertanto Vetra

Gas Power System. By Ertanto Vetra Gas Power System 1 By Ertanto Vetra Outlines Introduction Internal Combustion Engines Otto Cycles Diesel Cycles Gas Turbine Cycles Gas Turbine Based Combined Cycles Gas Turbines for Aircrafts Turbojets

More information

ICAL ENG LAB MANUAL. Dharmapuri Regulation : 2013 Branch : B.E. - Mechanical Engineering Year & Semester: II Year / IV Semester VVIT

ICAL ENG LAB MANUAL. Dharmapuri Regulation : 2013 Branch : B.E. - Mechanical Engineering Year & Semester: II Year / IV Semester VVIT Dharmapuri 636 703 LAB MANUAL Regulation : 2013 Branch : B.E. - Mechanical Engineering Year & Semester: II Year / IV Semester ME6412 -THERMAL ENGINEERING LABORATORY - I ICAL ENG 1 GENERAL INSTRUCTION All

More information

INTRODUCTION OF FOUR STROKE ENGINE

INTRODUCTION OF FOUR STROKE ENGINE INTRODUCTION OF FOUR STROKE ENGINE Engine: An engine is motor which converts chemical energy into mechanical energy Fuel/petrol engine: A petrol engine (known as a gasoline engine in North America) is

More information

ACTUAL CYCLE. Actual engine cycle

ACTUAL CYCLE. Actual engine cycle 1 ACTUAL CYCLE Actual engine cycle Introduction 2 Ideal Gas Cycle (Air Standard Cycle) Idealized processes Idealize working Fluid Fuel-Air Cycle Idealized Processes Accurate Working Fluid Model Actual

More information

Kul Internal Combustion Engine Technology. Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5

Kul Internal Combustion Engine Technology. Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5 Kul-14.4100 Internal Combustion Engine Technology Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5 Definitions Combustion engines convert the chemical energy of fuel to mechanical

More information

Chapter 1 Internal Combustion Engines

Chapter 1 Internal Combustion Engines Chapter 1 Internal Combustion Engines 1.1 Performance Parameters Engine performance parameters can be measured by two means; the indicator equipment or the dynamometer. The indicator system consists of

More information

Scheme G Sample Question Paper Course Name : Diploma in Automobile Engineering Course Code : AE

Scheme G Sample Question Paper Course Name : Diploma in Automobile Engineering Course Code : AE Sample Question Paper Semester : Fourth Marks : 100 Time: 03 Hours Q1.A. Attempt any SIX a. State different types of ideal gas processes 12 Marks b. Define dryness fraction and degree of superheat. c.

More information

TWO AND THREE WHEELERS QUESTION BANK UNIT I: POWER PLANT

TWO AND THREE WHEELERS QUESTION BANK UNIT I: POWER PLANT TWO AND THREE WHEELERS QUESTION BANK UNIT I: POWER PLANT What do you mean by scavenging? Why it is necessary? What are the types of scavenging pumps? What is scavenging pump? Draw symmetrical and unsymmetrical

More information

Unit WorkBook 4 Level 4 ENG U13 Fundamentals of Thermodynamics and Heat Engines UniCourse Ltd. All Rights Reserved. Sample

Unit WorkBook 4 Level 4 ENG U13 Fundamentals of Thermodynamics and Heat Engines UniCourse Ltd. All Rights Reserved. Sample Pearson BTEC Levels 4 Higher Nationals in Engineering (RQF) Unit 13: Fundamentals of Thermodynamics and Heat Engines Unit Workbook 4 in a series of 4 for this unit Learning Outcome 4 Internal Combustion

More information

Idealizations Help Manage Analysis of Complex Processes

Idealizations Help Manage Analysis of Complex Processes 8 CHAPTER Gas Power Cycles 8-1 Idealizations Help Manage Analysis of Complex Processes The analysis of many complex processes can be reduced to a manageable level by utilizing some idealizations (fig.

More information

Single-phase Coolant Flow and Heat Transfer

Single-phase Coolant Flow and Heat Transfer 22.06 ENGINEERING OF NUCLEAR SYSTEMS - Fall 2010 Problem Set 5 Single-phase Coolant Flow and Heat Transfer 1) Hydraulic Analysis of the Emergency Core Spray System in a BWR The emergency spray system of

More information

USO4CICV01/US04CICH02:

USO4CICV01/US04CICH02: Natubhai V. Patel College of Pure & Applied Sciences S. Y. B.Sc. Semester-4 Industrial chemistry/ IC (Vocational) USO4CICV0/US04CICH02: Chemical Plant Utilities UNIT 5 Internal combustion engine In an

More information

Additional examination-style questions

Additional examination-style questions 1 Figure 1 shows a remote-control camera used in space for inspecting space stations. The camera can be moved into position and rotated by firing thrusters which eject xenon gas at high speed. The camera

More information

Template for the Storyboard stage

Template for the Storyboard stage Template for the Storyboard stage Animation can be done in JAVA 2-D. Mention what will be your animation medium: 2D or 3D Mention the software to be used for animation development: JAVA, Flash, Blender,

More information

ME2301 THERMAL ENGINEERING L T P C OBJECTIVE: To integrate the concepts, laws and methodologies from the first course in thermo dynamics into

ME2301 THERMAL ENGINEERING L T P C OBJECTIVE: To integrate the concepts, laws and methodologies from the first course in thermo dynamics into ME2301 THERMAL ENGINEERING L T P C 3 1 0 4 OBJECTIVE: To integrate the concepts, laws and methodologies from the first course in thermo dynamics into analysis of cyclic processes To apply the thermodynamic

More information

Chapter 8 Production of Power from Heat

Chapter 8 Production of Power from Heat Chapter 8 Production of Power from Heat Different sources of power, such as solar energy (from sun), kinetic energy from atmospheric winds and potential energy from tides. The most important source of

More information

APPENDIX 1 TECHNICAL DATA OF TEST ENGINE

APPENDIX 1 TECHNICAL DATA OF TEST ENGINE 156 APPENDIX 1 TECHNICAL DATA OF TEST ENGINE Type Four-stroke Direct Injection Diesel Engine Engine make Kirloskar No. of cylinder One Type of cooling Air cooling Bore 87.5 mm Stroke 110 mm Displacement

More information

Gas Power Cycles. Tarawneh

Gas Power Cycles. Tarawneh Gas Power Cycles Dr.Mohammad Tarawneh ) Carnot cycle 2) Otto cycle ) Diesel cycle - Today 4) Dual Cycle 5) Stirling cycle 6) Ericsson cycles 7) Brayton cycle Carnot Cycle Reversible isothermal expansion

More information

Answer. 1 a) Attempt any SIX of the following: 12. i) i) List any four applications of IC Engine 2

Answer. 1 a) Attempt any SIX of the following: 12. i) i) List any four applications of IC Engine 2 (ISO/IEC - 700-005 Certified) Important Instructions to examiners: ) The answers should be examined by key words and not as word-to-word as given in the model answer scheme. ) The model answer and the

More information

Some important nomenclature: 1. Cylinder Bore (d) Inner diameter of cylinder 2. Piston area (A) Area of circle whose diameter is equal to the

Some important nomenclature: 1. Cylinder Bore (d) Inner diameter of cylinder 2. Piston area (A) Area of circle whose diameter is equal to the IC ENGINE An engine is a device which transforms one form of energy into another usable form. An engine in which combustion occurs inside the body of the engine itself, such an engine is knows as Internal

More information

Week 10. Gas Power Cycles. ME 300 Thermodynamics II 1

Week 10. Gas Power Cycles. ME 300 Thermodynamics II 1 Week 10 Gas Power Cycles ME 300 Thermodynamics II 1 Today s Outline Gas power cycles Internal combustion engines Four-stroke cycle Thermodynamic cycles Ideal cycle ME 300 Thermodynamics II 2 Gas Power

More information

Introduction to I.C Engines CH. 1. Prepared by: Dr. Assim Adaraje

Introduction to I.C Engines CH. 1. Prepared by: Dr. Assim Adaraje Introduction to I.C Engines CH. 1 Prepared by: Dr. Assim Adaraje 1 An internal combustion engine (ICE) is a heat engine where the combustion of a fuel occurs with an oxidizer (usually air) in a combustion

More information

BIODIESEL. Lesson 4d Test biodiesel in a diesel generator. Developed by Engineering and Technology Curriculum Team

BIODIESEL. Lesson 4d Test biodiesel in a diesel generator. Developed by Engineering and Technology Curriculum Team BIODIESEL Lesson 4d Test biodiesel in a diesel generator In a laboratory setting, test biodiesel in a diesel generator by estimating Btu. define energy density, kwh, and Btu calculate energy density, kwh

More information

Chapter 6. Supercharging

Chapter 6. Supercharging SHROFF S. R. ROTARY INSTITUTE OF CHEMICAL TECHNOLOGY (SRICT) DEPARTMENT OF MECHANICAL ENGINEERING. Chapter 6. Supercharging Subject: Internal Combustion Engine 1 Outline Chapter 6. Supercharging 6.1 Need

More information

DEPARTMENT OF MECHANICAL ENGINEERING ME ENGINEERING THERMODYNAMICS TWO MARKS QUESTION AND ANSWER

DEPARTMENT OF MECHANICAL ENGINEERING ME ENGINEERING THERMODYNAMICS TWO MARKS QUESTION AND ANSWER DEPARTMENT OF MECHANICAL ENGINEERING ME 6301- ENGINEERING THERMODYNAMICS TWO MARKS QUESTION AND ANSWER 1. Define the term thermal engineering. Ans: Thermal engineering is the science that deals with the

More information

LNR ENGINE CHAPTER - 5

LNR ENGINE CHAPTER - 5 LHR ENGINE CHAPTER - 5 LNR ENGINE 5.0 INTRODUCTION The studies on the performance of the conventional engine are shown in Chapter - 4. The research is extended to conduct experiments so as to improve the

More information

Thermodynamics cycles can be classified into different categories depending on fluid used or the different processes:

Thermodynamics cycles can be classified into different categories depending on fluid used or the different processes: Classification of thermodynamics cycles Thermodynamics cycles can be classified into different categories depending on fluid used or the different processes: Gas and vapor cycles - Gas cycle: the working

More information

MODEL ANSWER WINTER 18 EXAMINATION 17408

MODEL ANSWER WINTER 18 EXAMINATION 17408 Important Instructions to examiners: 1) The answers should be examined by key words and not as word-to-word as given in themodel answer scheme. 2) The model answer and the answer written by candidate may

More information

AME 436. Energy and Propulsion. Lecture 6 Unsteady-flow (reciprocating) engines 1: Basic operating principles, design & performance parameters

AME 436. Energy and Propulsion. Lecture 6 Unsteady-flow (reciprocating) engines 1: Basic operating principles, design & performance parameters AME 436 Energy and Propulsion Lecture 6 Unsteady-flow (reciprocating) engines 1: Basic operating principles, design & performance parameters Outline Classification of unsteady-flow engines Basic operating

More information

ENGINE & WORKING PRINCIPLES

ENGINE & WORKING PRINCIPLES ENGINE & WORKING PRINCIPLES A heat engine is a machine, which converts heat energy into mechanical energy. The combustion of fuel such as coal, petrol, diesel generates heat. This heat is supplied to a

More information