Engine Cycles. T Alrayyes

Size: px
Start display at page:

Download "Engine Cycles. T Alrayyes"

Transcription

1 Engine Cycles T Alrayyes

2 Introduction The cycle experienced in the cylinder of an internal combustion engine is very complex. The cycle in SI and diesel engine were discussed in detail in the previous chapter. Instead ideal cycles were assumed to make the process more manageable. Ideal cycle resemble true cycle but it is made of a lot of assumption.

3 WOT, naturally aspirated Engine

4 Assumption 1. Cylinder contains air during the total cycle and it is treated as ideal gas. 2. The specific heats and other physical and chemical properties remain unchanged during the cycle. 3. The real open cycle is changed into a closed cycle by assuming that the gases being exhausted are fed back into the intake system. 4. Instead of heat generation by combustion, heat is transformed from external heat source. 5. The process of heat removal in the exhaust gases is represented by heat transfer from the cycle to external heat sink Q out. 6. There is neither friction nor turbulence; all processes are assumed to be reversible. 7. The air is considered as an ideal gas

5 Ideal cycle Comparison between ideal and actual cycle

6

7 Air properties

8 WOT, naturally aspirated Engine

9 Assumption Actual engine processes are approximated with 4 ideal processes: 1. Isentropic during the compression and expansion stroke Assumed to be adiabatic and reversible process. Friction and heat transfer are ignored in the process 2. Constant pressure: during the intake and exhaust stroke The exhaust stroke is assumed to be constant at 1 atm. The inlet stroke will depend on the running conditions(wot, partially open and turbocharged) 3. Idealised combustion: is idealized by a constant-volume process (SI cycle), a constant-pressure process (CI cycle), or a combination of both (CIDual cycle). 1. exhaust blowby : is approximatedby a constant-volume process.

10 Otto Cycle 1 2 isentropic compression from V 1 to V addition of heat Q 23 at constant volume 3 4 isentropic expansion to the original volume 4 1 rejection of heat Q 41 at constant volume

11 Otto Cycle

12 Otto cycle

13 Otto cycle η t Otto = 1 T T T 1 T 2 T 3 1 T 2 Using the isentropic ideal gas relation and constant volume Where (V1/V2 = compression ratio r c ) and k is specific heat ratio Subsequently η t Otto = 1 1 c r k 1

14 Effect of compression ratio on thermal efficiency

15 Effect of r c and specific heat ratio

16 Diesel cycle Because of location and duration of combustion, diesel engine is based in constant pressure combustion rather than constant volume combustion. The rest of the cycle is identical to that of an SI engine

17 Diesel cycle

18

19

20

21 With the rearrangement, this can be shown to be equal, Where B = cutoff ratio Cutoff ratio is defined as the change in volume that occurs during combustion β = V 3 V 2 = v 3 v 2 = T 3 T 2

22 As the value of cut-off ratio increases ( heat addition is extended towards expansion) the efficiency is reduced due to additional heat required to compensate the expansion

23 Dual cycle Based on the equations of thermal efficiency of Otto and diesel engine. It can be concluded that Otto has a higher efficiency. Compression ignition would operate on the more efficient higher compression ratios, while constant-volume combustion of the Otto cycle would give higher efficiency for a given compression ratio. The modern high-speed CI engine accomplishes this in part by a simple operating change from early diesel engines. Instead of injecting the fuel late in the compression stroke near TDC, as was done in early engines, modern CI engines start to inject the fuel much earlier in the cycle, somewhere around 20 btdc Some of the combustion occurs almost at constant volume at TDC, much like the Otto cycle.

24 Dual cycle

25 Dual cycle

26 Cut-off ratio Pressure ratio, is defined as the rise in pressure during combustion, given as a ratio

27 Comparison of Otto, diesel and Dual Cycles: η t Otto = 1 1 r c k 1

28 Comparison of Otto, diesel and Dual Cycles: Direct comparison between the cycles based on the thermal efficiency equation will show that: The results suggest that the best combustion occur at constant volume and higher compression ratio

29 Comparison between Diesel and Otto cycle for the same compression ratio Thermal efficiency of the ideal Diesel cycle as a function of compression and cutoff ratios (k=1.4).

30 Comparison of Otto, diesel and Dual Cycles:

31 Comparison of Otto, diesel and Dual Cycles: s

32

33 Difference between Ideal cycle and real cycle Real cycle open with an open cycle and changing composition The gas inlet is different that outlet gas The mass flow rate is not the same (adding fuel after the induction, loss of mass during the cycle during to crevice and blowby) Treating the flow as air : Up to 7% is fuel After combustion the composition change Assuming an ideal gas with a constant specific volume Ideal gas is valid for low pressure but can deviate as the pressure increase Cp and Cv have high independence on temperature, can

34 Heat loss neglected During combustion lower peak temperature and pressure at the start of expansion Heat transfer during expansion and compression below ideal isentropic Cause a lower thermal efficiency. Perfect and Constant volume assumption Combustion starts btdc and continue atdc A quick but finite speed is desirable (steady pressure and force on the piston head causing a smooth engine cycle) A super sonic combustion would cause damage to the cycle Constant volume heat rejection It was assumed that exhaust blowby occur as the exhaust valve open due to pressure difference Exhaust blow by requires a finite time for that reason the exhaust valve must open 40 degree to 60 degree before bbdc

35 Valve timing Both exhaust and intake valve are not open exactly and BDC and TDC Intake valve is not closed until abdc due to flow restriction. Actual compression doesn t start until the valve is closed. Pressure is less than expected during combustion. Engine require finite time to actuate

36 Engine cycle at part throttling Part throttling create a flow restriction which causes a drop in inlet pressure. Fuel is also reduced to match the reduction in air. The more the throttle is close the higher the drop in pressure. This means that closing the throttle will reduce net work by reducing fuel (energy input Q in ) and increasing pumping loss

37

38

39 Supercharger and turbocharger Turbocharger has an adverse effect than a throttle Turbocharger will increase the inlet pressure above atmospheric pressure More fuel and air (more energy Q in ) Increase in air temperature in the intake stroke (compressive heating). Subsequently increase temperature at the compression stroke and the rest of the cycle. This might cause self ignition and knocking problems. Aftercooler might be used in some engines

40 The throttling and turbocharging effect on net work is captured through the following: Work done during the intake stroke is, Where V d is the displacement volume Work done on the exhaust stroke Total work is

41 Exhaust process The exhaust process contains two processes: The blowby: sudden drop in pressure large percentage of the gas leaves until pressure equalize Exhaust stroke: still some exhaust in the chamber and exhaust pushed by compression The temperature cool by expansion during the process. The temperature is initially cooled due to drop in pressure As the exhaust is pushed, a high kinetic energy is generated due high velocity flow This energy is transferd into enthalpy and temperature.

42 Initially drop to T 7, Although this expansion is not reversible, the ideal gas isentropic relationship between pressure and temperature serves as a good model to approximate exhaust temperature T7 in the hypothetical process

43 The state of the exhaust gas during the exhaust stroke is best approximated by a pressure of 1 Atm, a temperature of T7 and a specific volume shown at point 7.

Internal Combustion Engines

Internal Combustion Engines Internal Combustion Engines Reading Problems 8-3 8-7 8-35, 8-45, 8-52 Definitions 1. spark ignition: a mixture of fuel and air is ignited by a spark plug applications requiring power to about 225 kw (300

More information

(v) Cylinder volume It is the volume of a gas inside the cylinder when the piston is at Bottom Dead Centre (B.D.C) and is denoted by V.

(v) Cylinder volume It is the volume of a gas inside the cylinder when the piston is at Bottom Dead Centre (B.D.C) and is denoted by V. UNIT II GAS POWER CYCLES AIR STANDARD CYCLES Air standard cycles are used for comparison of thermal efficiencies of I.C engines. Engines working with air standard cycles are known as air standard engines.

More information

ACTUAL CYCLE. Actual engine cycle

ACTUAL CYCLE. Actual engine cycle 1 ACTUAL CYCLE Actual engine cycle Introduction 2 Ideal Gas Cycle (Air Standard Cycle) Idealized processes Idealize working Fluid Fuel-Air Cycle Idealized Processes Accurate Working Fluid Model Actual

More information

VALVE TIMING DIAGRAM FOR SI ENGINE VALVE TIMING DIAGRAM FOR CI ENGINE

VALVE TIMING DIAGRAM FOR SI ENGINE VALVE TIMING DIAGRAM FOR CI ENGINE VALVE TIMING DIAGRAM FOR SI ENGINE VALVE TIMING DIAGRAM FOR CI ENGINE Page 1 of 13 EFFECT OF VALVE TIMING DIAGRAM ON VOLUMETRIC EFFICIENCY: Qu. 1:Why Inlet valve is closed after the Bottom Dead Centre

More information

Internal Combustion Engines

Internal Combustion Engines Engine Cycles Lecture Outline In this lecture we will: Analyse actual air fuel engine cycle: -Stroke cycle -Stroke cycle Compare these cycles to air standard cycles Actual Engine Cycle Although air standard

More information

Idealizations Help Manage Analysis of Complex Processes

Idealizations Help Manage Analysis of Complex Processes 8 CHAPTER Gas Power Cycles 8-1 Idealizations Help Manage Analysis of Complex Processes The analysis of many complex processes can be reduced to a manageable level by utilizing some idealizations (fig.

More information

L34: Internal Combustion Engine Cycles: Otto, Diesel, and Dual or Gas Power Cycles Introduction to Gas Cycles Definitions

L34: Internal Combustion Engine Cycles: Otto, Diesel, and Dual or Gas Power Cycles Introduction to Gas Cycles Definitions Page L: Internal Combustion Engine Cycles: Otto, Diesel, and Dual or Gas Power Cycles Review of Carnot Power Cycle (gas version) Air-Standard Cycles Internal Combustion (IC) Engines - Otto and Diesel Cycles

More information

Design and Fabrication of Simple Turbo Alternator

Design and Fabrication of Simple Turbo Alternator Design and Fabrication of Simple Turbo Alternator S.Arunkumar, A.Sridhar, S.Praveen vaitheeswaran, S.Sasikumar, Sefin Jose Department of mechanical engineering, Nandha College of technology, Erode. Abstract

More information

density ratio of 1.5.

density ratio of 1.5. Problem 1: An 8cyl 426 ci Hemi motor makes 426 HP at 5500 rpm on a compression ratio of 10.5:1. It is over square by 10% meaning that it s stroke is 10% less than it s bore. It s volumetric efficiency

More information

Week 10. Gas Power Cycles. ME 300 Thermodynamics II 1

Week 10. Gas Power Cycles. ME 300 Thermodynamics II 1 Week 10 Gas Power Cycles ME 300 Thermodynamics II 1 Today s Outline Gas power cycles Internal combustion engines Four-stroke cycle Thermodynamic cycles Ideal cycle ME 300 Thermodynamics II 2 Gas Power

More information

Internal combustion engines can be classified in a number of different ways: 1. Types of Ignition

Internal combustion engines can be classified in a number of different ways: 1. Types of Ignition Chapter 1 Introduction 1-3 ENGINE CLASSIFICATIONS Internal combustion engines can be classified in a number of different ways: 1. Types of Ignition 1 (a) Spark Ignition (SI). An SI engine starts the combustion

More information

Assignment-1 Air Standard Cycles

Assignment-1 Air Standard Cycles Assignment-1 Air Standard Cycles 1. What do u mean by air standard cycle? List assumptions for air standard cycle & give reasons why air standard cycle differs from actual cycle. 2. Derive an equation

More information

Gas Power System. By Ertanto Vetra

Gas Power System. By Ertanto Vetra Gas Power System 1 By Ertanto Vetra Outlines Introduction Internal Combustion Engines Otto Cycles Diesel Cycles Gas Turbine Cycles Gas Turbine Based Combined Cycles Gas Turbines for Aircrafts Turbojets

More information

Chapter 8 Production of Power from Heat

Chapter 8 Production of Power from Heat Chapter 8 Production of Power from Heat Different sources of power, such as solar energy (from sun), kinetic energy from atmospheric winds and potential energy from tides. The most important source of

More information

Prepared by: Dr. Assim Adaraje

Prepared by: Dr. Assim Adaraje Air-standard cycles Prepared by: Dr. Assim Adaraje CH. 2 ۱ Cold-air-standard assumptions: When the working fluid is considered to be air with constant specific heats at room temperature (25 C). Air-standard

More information

Heat Transfer in Engines. Internal Combustion Engines

Heat Transfer in Engines. Internal Combustion Engines Heat Transfer in Engines Internal Combustion Engines Energy Distribution Removing heat is critical in keeping an engine and lubricant from thermal failure Amount of energy available for use: Brake thermal

More information

Gas Power Cycles. Tarawneh

Gas Power Cycles. Tarawneh Gas Power Cycles Dr.Mohammad Tarawneh ) Carnot cycle 2) Otto cycle ) Diesel cycle - Today 4) Dual Cycle 5) Stirling cycle 6) Ericsson cycles 7) Brayton cycle Carnot Cycle Reversible isothermal expansion

More information

Class Notes on Thermal Energy Conversion System

Class Notes on Thermal Energy Conversion System Class Notes on Thermal Energy Conversion System For the students of Civil & Rural 3 rd semester Ramesh Khanal Assistant Professorr Nepal Engineering College Bhaktapur, Nepal 2015 Course Structure MEC 209.3:

More information

Assignment-1 Introduction

Assignment-1 Introduction Assignment-1 Introduction 1. Compare S.I. engines with C.I engines. 2. Explain with the help of neat sketch, the working of a 2-stroke petrol engine. 3. Derive an equation of efficiency, work output and

More information

AT AUTOMOTIVE ENGINES QUESTION BANK

AT AUTOMOTIVE ENGINES QUESTION BANK AT6301 - AUTOMOTIVE ENGINES QUESTION BANK UNIT I: CONSTRUCTION & WORKING PRINCIPLE OF IC ENGINES 1. State the application of CI engines? 2. What is Cubic capacity of an engine? 3. What is the purpose of

More information

(a) then mean effective pressure and the indicated power for each end ; (b) the total indicated power : [16]

(a) then mean effective pressure and the indicated power for each end ; (b) the total indicated power : [16] Code No: R05220304 Set No. 1 II B.Tech II Semester Regular Examinations, Apr/May 2007 THERMAL ENGINEERING-I ( Common to Mechanical Engineering and Automobile Engineering) Time: 3 hours Max Marks: 80 Answer

More information

Chapter 9 GAS POWER CYCLES

Chapter 9 GAS POWER CYCLES Thermodynamics: An Engineering Approach Seventh Edition in SI Units Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2011 Chapter 9 GAS POWER CYCLES Mehmet Kanoglu University of Gaziantep Copyright The McGraw-Hill

More information

In this lecture... Gas power cycles

In this lecture... Gas power cycles 7 Lect-7 Gas power cycles In this lecture... he Carnot cycle and its significance Air-standard assumptions An oeriew of reciprocating engines Otto cycle: the ideal cycle for sparkignition engines Diesel

More information

Combustion engines. Combustion

Combustion engines. Combustion Combustion engines Chemical energy in fuel converted to thermal energy by combustion or oxidation Heat engine converts chemical energy into mechanical energy Thermal energy raises temperature and pressure

More information

Unit WorkBook 4 Level 4 ENG U13 Fundamentals of Thermodynamics and Heat Engines UniCourse Ltd. All Rights Reserved. Sample

Unit WorkBook 4 Level 4 ENG U13 Fundamentals of Thermodynamics and Heat Engines UniCourse Ltd. All Rights Reserved. Sample Pearson BTEC Levels 4 Higher Nationals in Engineering (RQF) Unit 13: Fundamentals of Thermodynamics and Heat Engines Unit Workbook 4 in a series of 4 for this unit Learning Outcome 4 Internal Combustion

More information

CHAPTER I GAS POWER CYCLES

CHAPTER I GAS POWER CYCLES CHAPTER I GAS POWER CYCLES 1.1 AIR STANDARD CYCLES Air standard cycles are used for comparison of thermal efficiencies of I.C engines. Engines working with air standard cycles are known as air standard

More information

Chapter 9 GAS POWER CYCLES

Chapter 9 GAS POWER CYCLES Thermodynamics: An Engineering Approach, 6 th Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2008 Chapter 9 GAS POWER CYCLES Copyright The McGraw-Hill Companies, Inc. Permission required for reproduction

More information

SAMPLE STUDY MATERIAL

SAMPLE STUDY MATERIAL IC Engine - ME GATE, IES, PSU 1 SAMPLE STUDY MATERIAL Mechanical Engineering ME Postal Correspondence Course Internal Combustion Engine GATE, IES & PSUs IC Engine - ME GATE, IES, PSU 2 C O N T E N T 1.

More information

The Internal combustion engine (Otto Cycle)

The Internal combustion engine (Otto Cycle) The Internal combustion engine (Otto Cycle) The Otto cycle is a set of processes used by spark ignition internal combustion engines (2-stroke or 4-stroke cycles). These engines a) ingest a mixture of fuel

More information

Comparison of Air-Standard Atkinson, Diesel and Otto Cycles with Constant Specific Heats

Comparison of Air-Standard Atkinson, Diesel and Otto Cycles with Constant Specific Heats Comparison of Air-Standard Atkinson, Diesel and Otto Cycles with Constant Specific Heats Sethi Upasna Vijay 1, Mansha Kumari 2 1 Assistant Professor, Mechanical Engineering Department, Vadodara Institute

More information

Chapter 6. Supercharging

Chapter 6. Supercharging SHROFF S. R. ROTARY INSTITUTE OF CHEMICAL TECHNOLOGY (SRICT) DEPARTMENT OF MECHANICAL ENGINEERING. Chapter 6. Supercharging Subject: Internal Combustion Engine 1 Outline Chapter 6. Supercharging 6.1 Need

More information

SI engine combustion

SI engine combustion SI engine combustion 1 SI engine combustion: How to burn things? Reactants Products Premixed Homogeneous reaction Not limited by transport process Fast/slow reactions compared with other time scale of

More information

η th W = Q Gas Power Cycles: Working fluid remains in the gaseous state through the cycle.

η th W = Q Gas Power Cycles: Working fluid remains in the gaseous state through the cycle. Gas Power Cycles: Gas Power Cycles: Working fluid remains in the gaseous state through the cycle. Sometimes useful to study an idealised cycle in which internal irreversibilities and complexities are

More information

Combustion Systems What we might have learned

Combustion Systems What we might have learned Combustion Systems What we might have learned IMechE ADSC, 6 December 2012 Chris Whelan Contents Engines Big & Small Carnot, Otto & Diesel Thermodynamic Cycles Combustion Process & Systems Diesel & Otto

More information

2013 THERMAL ENGINEERING-I

2013 THERMAL ENGINEERING-I SET - 1 II B. Tech II Semester, Regular Examinations, April/May 2013 THERMAL ENGINEERING-I (Com. to ME, AME) Time: 3 hours Max. Marks: 75 Answer any FIVE Questions All Questions carry Equal Marks ~~~~~~~~~~~~~~~~~~~~~~~~

More information

UNIT 1 GAS POWER CYCLES

UNIT 1 GAS POWER CYCLES THERMAL ENGINEERING UNIT 1 GAS POWER CYCLES Air Standard Cycles - Otto, Diesel, Dual, Brayton cycle with intercooling, reheating and regeneration- Calculation of airstandard efficiency and mean effective

More information

COVENANT UNIVERSITY NIGERIA TUTORIAL KIT OMEGA SEMESTER PROGRAMME: MECHANICAL ENGINEERING

COVENANT UNIVERSITY NIGERIA TUTORIAL KIT OMEGA SEMESTER PROGRAMME: MECHANICAL ENGINEERING COVENANT UNIVERSITY NIGERIA TUTORIAL KIT OMEGA SEMESTER PROGRAMME: MECHANICAL ENGINEERING COURSE: MCE 320 DISCLAIMER The contents of this document are intended for practice and leaning purposes at the

More information

Thermodynamics cycles can be classified into different categories depending on fluid used or the different processes:

Thermodynamics cycles can be classified into different categories depending on fluid used or the different processes: Classification of thermodynamics cycles Thermodynamics cycles can be classified into different categories depending on fluid used or the different processes: Gas and vapor cycles - Gas cycle: the working

More information

Principles of Engine Operation. Information

Principles of Engine Operation. Information Internal Combustion Engines MAK 4070E Principles of Engine Operation Prof.Dr. Cem Soruşbay Istanbul Technical University Information Prof.Dr. Cem Soruşbay İ.T.Ü. Makina Fakültesi Motorlar ve Taşıtlar Laboratuvarı

More information

Chapter 9. Two important areas of application for thermodynamics GAS POWER CYCLES. Objectives

Chapter 9. Two important areas of application for thermodynamics GAS POWER CYCLES. Objectives Chapter 9 GAS POWER CYCLES Two important areas of application for thermodynamics are power generation and refrigeration. Both are usually accomplished by systems that operate on a thermodynamic cycle.

More information

ADDIS ABABA UNIVERSITY INSTITUTE OF TECHNOLOGY

ADDIS ABABA UNIVERSITY INSTITUTE OF TECHNOLOGY 1 INTERNAL COMBUSTION ENGINES ADDIS ABABA UNIVERSITY INSTITUTE OF TECHNOLOGY MECHANICAL ENGINEERING DEPARTMENT DIVISON OF THERMAL AND ENERGY CONVERSION IC Engine Fundamentals 2 Engine Systems An engine

More information

Internal Combustion Engines

Internal Combustion Engines Air and Fuel Induction Lecture 3 1 Outline In this lecture we will discuss the following: A/F mixture preparation in gasoline engines using carburetion. Air Charging technologies: Superchargers Turbochargers

More information

Simple Finite Heat Release Model (SI Engine)

Simple Finite Heat Release Model (SI Engine) Simple Finite Heat Release Model (SI Engine) Introduction In the following, a finite burn duration is taken into account, in which combustion occurs at θ soc (Start Of Combustion), and continues until

More information

SUPERCHARGER AND TURBOCHARGER

SUPERCHARGER AND TURBOCHARGER SUPERCHARGER AND TURBOCHARGER 1 Turbocharger and supercharger 2 To increase the output of any engine more fuel can be burned and make bigger explosion in every cycle. i. One way to add power is to build

More information

Internal Combustion Engine

Internal Combustion Engine Internal Combustion Engine 1. A 9-cylinder, 4-stroke cycle, radial SI engine operates at 900rpm. Calculate: (1) How often ignition occurs, in degrees of engine rev. (2) How many power strokes per rev.

More information

Kul Internal Combustion Engine Technology

Kul Internal Combustion Engine Technology Kul-14.4100 Internal Combustion Engine Technology Gas Exchange, 2015 Topics Gas exchange in four stroke engines Volumetric efficiency Valves and valve flow Two stroke engine scavenging Camshaft and intake

More information

Gas exchange Processes. Typical valve timing diagram

Gas exchange Processes. Typical valve timing diagram Gas exchange Processes To move working fluid in and out of engine Engine performance is air limited Engines are usually optimized for maximum power at high speed Considerations 4-stroke engine: volumetric

More information

SET - 1 II B. Tech II Semester Regular/Supplementary Examinations, April/May-2017 THERMAL ENGINEERING-I (Mechanical Engineering) Time: 3 hours Max. Marks: 70 Note: 1. Question Paper consists of two parts

More information

USO4CICV01/US04CICH02:

USO4CICV01/US04CICH02: Natubhai V. Patel College of Pure & Applied Sciences S. Y. B.Sc. Semester-4 Industrial chemistry/ IC (Vocational) USO4CICV0/US04CICH02: Chemical Plant Utilities UNIT 5 Internal combustion engine In an

More information

Development, Implementation, and Validation of a Fuel Impingement Model for Direct Injected Fuels with High Enthalpy of Vaporization

Development, Implementation, and Validation of a Fuel Impingement Model for Direct Injected Fuels with High Enthalpy of Vaporization Development, Implementation, and Validation of a Fuel Impingement Model for Direct Injected Fuels with High Enthalpy of Vaporization (SAE Paper- 2009-01-0306) Craig D. Marriott PE, Matthew A. Wiles PE,

More information

2.61 Internal Combustion Engines

2.61 Internal Combustion Engines Due: Thursday, February 19, 2004 2.61 Internal Combustion Engines Problem Set 2 Tuesday, February 10, 2004 1. Several velocities, time, and length scales are useful in understanding what goes on inside

More information

Simulation of Performance Parameters of Spark Ignition Engine for Various Ignition Timings

Simulation of Performance Parameters of Spark Ignition Engine for Various Ignition Timings Research Article International Journal of Current Engineering and Technology ISSN 2277-4106 2013 INPRESSCO. All Rights Reserved. Available at http://inpressco.com/category/ijcet Simulation of Performance

More information

Kul Internal Combustion Engine Technology. Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5

Kul Internal Combustion Engine Technology. Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5 Kul-14.4100 Internal Combustion Engine Technology Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5 Definitions Combustion engines convert the chemical energy of fuel to mechanical

More information

GAS POWER CYCLES. Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University

GAS POWER CYCLES. Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University Chapter 9 GAS POWER CYCLES Dr Ali Jawarneh Department of Mechanical Engineering i Hashemite University 2 Objectives Evaluate the performance of gas power cycles for which h the working fluid remains a

More information

Which are the four important control loops of an spark ignition (SI) engine?

Which are the four important control loops of an spark ignition (SI) engine? 151-0567-00 Engine Systems (HS 2017) Exercise 1 Topic: Lecture 1 Johannes Ritzmann (jritzman@ethz.ch), Raffi Hedinger (hraffael@ethz.ch); October 13, 2017 Problem 1 (Control Systems) Why do we use control

More information

Reciprocating Internal Combustion Engines

Reciprocating Internal Combustion Engines Part 2: Turbochargers, Engine Performance Metrics Reciprocating Internal Combustion Engines Prof. Rolf D. Reitz Engine Research Center University of Wisconsin-Madison 2014 Princeton-CEFRC Summer School

More information

UNIT 2 POWER PLANTS 2.1 INTRODUCTION 2.2 CLASSIFICATION OF IC ENGINES. Objectives. Structure. 2.1 Introduction

UNIT 2 POWER PLANTS 2.1 INTRODUCTION 2.2 CLASSIFICATION OF IC ENGINES. Objectives. Structure. 2.1 Introduction UNIT 2 POWER PLANTS Power Plants Structure 2.1 Introduction Objectives 2.2 Classification of IC Engines 2.3 Four Stroke Engines versus Two Stroke Engines 2.4 Working of Four Stroke Petrol Engine 2.5 Working

More information

Combustion. T Alrayyes

Combustion. T Alrayyes Combustion T Alrayyes Fluid motion with combustion chamber Turbulence Swirl SQUISH AND TUMBLE Combustion in SI Engines Introduction The combustion in SI engines inside the engine can be divided into three

More information

Development of Low-Exergy-Loss, High-Efficiency Chemical Engines

Development of Low-Exergy-Loss, High-Efficiency Chemical Engines Development of Low-Exergy-Loss, High-Efficiency Chemical Engines Investigators C. F., Associate Professor, Mechanical Engineering; Kwee-Yan Teh, Shannon L. Miller, Graduate Researchers Introduction The

More information

Foundations of Thermodynamics and Chemistry. 1 Introduction Preface Model-Building Simulation... 5 References...

Foundations of Thermodynamics and Chemistry. 1 Introduction Preface Model-Building Simulation... 5 References... Contents Part I Foundations of Thermodynamics and Chemistry 1 Introduction... 3 1.1 Preface.... 3 1.2 Model-Building... 3 1.3 Simulation... 5 References..... 8 2 Reciprocating Engines... 9 2.1 Energy Conversion...

More information

MEB THERMAL ENGINEERING - I QUESTION BANK UNIT-I PART-A

MEB THERMAL ENGINEERING - I QUESTION BANK UNIT-I PART-A MEB 420 - THERMAL ENGINEERING - I QUESTION BANK UNIT-I Each question carries 1 mark. PART-A 1. Define temperature. 2. Define intensive property 3. Explain the term absolute zero of temperature 4. State

More information

ENGINES ENGINE OPERATION

ENGINES ENGINE OPERATION ENGINES ENGINE OPERATION Because the most widely used piston engine is the four-stroke cycle type, it will be used as the example for this section, Engine Operation and as the basis for comparison in the

More information

EEN-E2002, Gas exchange and supercharging, lecture 4a

EEN-E2002, Gas exchange and supercharging, lecture 4a EEN-E2002, Gas exchange and supercharging, lecture 4a Basshuysen Chapter 11 Supercharging of Internal Combustion Engines Heywood Chapter 6 Gas exchange process January 2017, Martti Larmi Gas Exchange in

More information

Internal Combustion Engines

Internal Combustion Engines Introduction Lecture 1 1 Outline In this lecture we will learn about: Definition of internal combustion Development of the internal combustion engine Different engine classifications We will also draw

More information

UNIT IV INTERNAL COMBUSTION ENGINES

UNIT IV INTERNAL COMBUSTION ENGINES UNIT IV INTERNAL COMBUSTION ENGINES Objectives After the completion of this chapter, Students 1. To know the different parts of IC engines and their functions. 2. To understand the working principle of

More information

Chapter 1 Internal Combustion Engines

Chapter 1 Internal Combustion Engines Chapter 1 Internal Combustion Engines 1.1 Performance Parameters Engine performance parameters can be measured by two means; the indicator equipment or the dynamometer. The indicator system consists of

More information

GYANMANJARI INSTITUTE OF TECHNOLOGY (GMIT) SUBJECT: ELEMENTS OF MECHANICAL ENGINEERING Assignment Ch 1

GYANMANJARI INSTITUTE OF TECHNOLOGY (GMIT) SUBJECT: ELEMENTS OF MECHANICAL ENGINEERING Assignment Ch 1 1. 3. GYANMANJARI INSTITUTE OF TECHNOLOGY (GMIT) Assignment Ch 1 A steel ball having mass of 10 kg and a specific heat of 460 J/kg K is heated from 50 o C to 200 o C. Determine the heat required. In a

More information

Vol-3 Issue India 2 Assistant Professor, Mechanical Engineering Dept., Hansaba College of Engineering & Technology, Gujarat, India

Vol-3 Issue India 2 Assistant Professor, Mechanical Engineering Dept., Hansaba College of Engineering & Technology, Gujarat, India Review Paper on Effect of Variable Thermal Properties of Working Fluid on Performance of an IC Engine Cycle Desai Rahulkumar Mohanbhai 1, Kiran D. Parmar 2 1 P. G. Student, Mechanical Engineering Dept.,

More information

Internal Combustion Engine. Prepared by- Md Ferdous Alam Lecturer, MEE, SUST

Internal Combustion Engine. Prepared by- Md Ferdous Alam Lecturer, MEE, SUST Internal Combustion Engine Prepared by- Md Ferdous Alam Lecturer, MEE, SUST What is an Engine? -a machine designed to convert one form of energy into mechanical energy Two types of engines : 1. Internal

More information

Normal vs Abnormal Combustion in SI engine. SI Combustion. Turbulent Combustion

Normal vs Abnormal Combustion in SI engine. SI Combustion. Turbulent Combustion Turbulent Combustion The motion of the charge in the engine cylinder is always turbulent, when it is reached by the flame front. The charge motion is usually composed by large vortexes, whose length scales

More information

Problem 1 (ECU Priority)

Problem 1 (ECU Priority) 151-0567-00 Engine Systems (HS 2016) Exercise 6 Topic: Optional Exercises Raffi Hedinger (hraffael@ethz.ch), Norbert Zsiga (nzsiga@ethz.ch); November 28, 2016 Problem 1 (ECU Priority) Use the information

More information

OBJECTIVE: GENERAL ASPECTS ABOUT ENGINES MECHANISM:

OBJECTIVE: GENERAL ASPECTS ABOUT ENGINES MECHANISM: LANDMARK UNIVERSITY, OMU-ARAN LECTURE NOTE 3 COLLEGE: COLLEGE OF SCIENCE AND ENGINEERING DEPARTMENT: MECHANICAL ENGINEERING Course code: MCE 211 Course title: Introduction to Mechanical Engineering Credit

More information

LECTURE NOTES INTERNAL COMBUSTION ENGINES SI AN INTEGRATED EVALUATION

LECTURE NOTES INTERNAL COMBUSTION ENGINES SI AN INTEGRATED EVALUATION LECTURE NOTES on INTERNAL COMBUSTION ENGINES SI AN INTEGRATED EVALUATION Integrated Master Course on Mechanical Engineering Mechanical Engineering Department November 2015 Approach SI _ indirect injection

More information

Template for the Storyboard stage

Template for the Storyboard stage Template for the Storyboard stage Animation can be done in JAVA 2-D. Mention what will be your animation medium: 2D or 3D Mention the software to be used for animation development: JAVA, Flash, Blender,

More information

Internal Combustion Engines TUTORIAL

Internal Combustion Engines TUTORIAL Internal Combustion Engines TUTORIAL College of Engineering Mechanical Engineering Department Academic Year 2012-2013 Class 3 rd Year Class Subject Lecturer Internal Combustion Engines Dr. Raoof M. Radhi

More information

Investigators: C. F. Edwards, Associate Professor, Mechanical Engineering Department; M.N. Svreck, K.-Y. Teh, Graduate Researchers

Investigators: C. F. Edwards, Associate Professor, Mechanical Engineering Department; M.N. Svreck, K.-Y. Teh, Graduate Researchers Development of Low-Irreversibility Engines Investigators: C. F. Edwards, Associate Professor, Mechanical Engineering Department; M.N. Svreck, K.-Y. Teh, Graduate Researchers This project aims to implement

More information

Introduction to I.C Engines CH. 1. Prepared by: Dr. Assim Adaraje

Introduction to I.C Engines CH. 1. Prepared by: Dr. Assim Adaraje Introduction to I.C Engines CH. 1 Prepared by: Dr. Assim Adaraje 1 An internal combustion engine (ICE) is a heat engine where the combustion of a fuel occurs with an oxidizer (usually air) in a combustion

More information

2. Discuss the effects of the following operating variables on detonation

2. Discuss the effects of the following operating variables on detonation Code No: RR220303 Set No. 1 II B.Tech II Semester Regular Examinations, Apr/May 2006 THERMAL ENGINEERING-I ( Common to Mechanical Engineering and Automobile Engineering) Time: 3 hours Max Marks: 80 Answer

More information

Diesel Engine Fundamentals Part 2 Course# ME406

Diesel Engine Fundamentals Part 2 Course# ME406 Diesel Engine Fundamentals Part 2 Course# ME406 EZpdh.com All Rights Reserved Diesel Engine Fundamentals DOE-HDBK-1018/1-93 DIESEL ENGINES Air Intake System Because a diesel engine requires close tolerances

More information

Power Cycles. Ideal Cycles, Internal Combustion

Power Cycles. Ideal Cycles, Internal Combustion Gas Power Cycles Power Cycles Ideal Cycles, Internal Combustion Otto cycle, spark ignition Diesel cycle, compression ignition Sterling & Ericsson cycles Brayton cycles Jet-propulsion cycle Ideal Cycles,

More information

ENGINE 1ZZ-FE ENGINE DESCRIPTION EG-1 ENGINE - 1ZZ-FE ENGINE

ENGINE 1ZZ-FE ENGINE DESCRIPTION EG-1 ENGINE - 1ZZ-FE ENGINE EG-1 ENGINE - 1ZZ-FE ENGINE ENGINE 1ZZ-FE ENGINE DESCRIPTION The VVT-i (Variable Valve Timing-intelligent) system, the DIS (Direct Ignition System), and a plastic intake manifold have been used on the

More information

Focus on Training Section: Unit 2

Focus on Training Section: Unit 2 All Pump Types Page 1 1. Title Page Learning objectives Become familiar with the 4 stroke cycle Become familiar with diesel combustion process To understand how timing affects emissions To understand the

More information

VETRI VINAYAHA COLLEGE OF ENGINEERING AND TECHNOLOGY DEPARTMENT OF MECHANICAL ENGINEERING ME6404 THERMAL ENGINEERING

VETRI VINAYAHA COLLEGE OF ENGINEERING AND TECHNOLOGY DEPARTMENT OF MECHANICAL ENGINEERING ME6404 THERMAL ENGINEERING VETRI VINAYAHA COLLEGE OF ENGINEERING AND TECHNOLOGY DEPARTMENT OF MECHANICAL ENGINEERING ME6404 THERMAL ENGINEERING UNIT I - GAS POWER CYCLES 1. What is a thermodynamic cycle? Thermodynamic cycle is defined

More information

Applied Thermodynamics Internal Combustion Engines

Applied Thermodynamics Internal Combustion Engines Applied Thermodynamics Internal Combustion Engines Assoc. Prof. Dr. Mazlan Abdul Wahid Faculty of Mechanical Engineering Universiti Teknologi Malaysia www.fkm.utm.my/~mazlan 1 Coverage Introduction Operation

More information

Important Instructions to examiners: 1) The answers should be examined by key words and not as word-to-word as given in the model answer scheme. 2) The model answer and the answer written by candidate

More information

LNR ENGINE CHAPTER - 5

LNR ENGINE CHAPTER - 5 LHR ENGINE CHAPTER - 5 LNR ENGINE 5.0 INTRODUCTION The studies on the performance of the conventional engine are shown in Chapter - 4. The research is extended to conduct experiments so as to improve the

More information

Fuel control. The fuel injection system tasks. Starting fuel pump (FP)

Fuel control. The fuel injection system tasks. Starting fuel pump (FP) 1 Fuel control The fuel injection system tasks - To provide fuel - To distribute the fuel between the cylinders - To provide the correct quantity of fuel Starting fuel pump (FP) The control module (1)

More information

CHAPTER 3 ENGINE TYPES

CHAPTER 3 ENGINE TYPES CHAPTER 3 CHAPTER 3 ENGINE TYPES CONTENTS PAGE Multi-Cylinders 02 Firing orders 06 2 Stroke Cycle 08 Diesel Cycle 10 Wankel Engine 12 Radial/Rotary 14 Engine Types Multi Cylinders Below are illustrated

More information

WEEK 4 Dynamics of Machinery

WEEK 4 Dynamics of Machinery WEEK 4 Dynamics of Machinery References Theory of Machines and Mechanisms, J.J.Uicker, G.R.Pennock ve J.E. Shigley, 2003 Prof.Dr.Hasan ÖZTÜRK 1 DYNAMICS OF RECIPROCATING ENGINES Prof.Dr.Hasan ÖZTÜRK The

More information

Potential of Large Output Power, High Thermal Efficiency, Near-zero NOx Emission, Supercharged, Lean-burn, Hydrogen-fuelled, Direct Injection Engines

Potential of Large Output Power, High Thermal Efficiency, Near-zero NOx Emission, Supercharged, Lean-burn, Hydrogen-fuelled, Direct Injection Engines Available online at www.sciencedirect.com Energy Procedia 29 (2012 ) 455 462 World Hydrogen Energy Conference 2012 Potential of Large Output Power, High Thermal Efficiency, Near-zero NOx Emission, Supercharged,

More information

Process 1-2: Reversible adiabatic compression process. Process 2-3: Reversible isothermal heat addition

Process 1-2: Reversible adiabatic compression process. Process 2-3: Reversible isothermal heat addition Vapor Power Cycles Process 1-2: Reversible adiabatic compression process from P1 to P2. Process 2-3: Reversible isothermal heat addition process at constant temperature TH. Process 3-4: Reversible adiabatic

More information

Homogeneous Charge Compression Ignition (HCCI) Engines

Homogeneous Charge Compression Ignition (HCCI) Engines Homogeneous Charge Compression Ignition (HCCI) Engines Aravind. I. Garagad. Shri Dharmasthala Manjunatheshwara College of Engineering and Technology, Dharwad, Karnataka, India. ABSTRACT Large reductions

More information

AE 1005 AUTOMOTIVE ENGINES COMBUSTION IN SI ENGINES

AE 1005 AUTOMOTIVE ENGINES COMBUSTION IN SI ENGINES AE 1005 AUTOMOTIVE ENGINES COMBUSTION IN SI ENGINES Syllabus Combustion in premixed and diffusion flames - Combustion process in IC engines. Stages of combustion - Flame propagation - Flame velocity and

More information

Approved by AICTE, Government of India & affiliated to Dr. A.P.J. Abdul Kalam Technical University, Lucknow Department of Mechanical Engineering

Approved by AICTE, Government of India & affiliated to Dr. A.P.J. Abdul Kalam Technical University, Lucknow Department of Mechanical Engineering Experiment No. - 1 Object: Study and working of four stroke petrol engine. Apparatus Required: S. No. Name of Apparatus Specifications Model of Four stroke petrol engine NA Figure 1: Working of four stroke

More information

Thermal Engines (Motores Térmicos)

Thermal Engines (Motores Térmicos) Thermal Engines (Motores Térmicos) Tutorials Time schedule Hour/Day Monday Tuesday Wednesday Thursday Friday 11:00 12:00 MT MT MT 1 Tutorial 1 Engine Parts and Components Engine performance maps The reciprocating

More information

THE FOUR STROKE CYCLE BUT HOW DOES IT WORK EXACTLY? LET S LOOK IN MORE DETAIL 1. INDUCTION SUCK 2. COMPRESSION 3. COMBUSTION 4.

THE FOUR STROKE CYCLE BUT HOW DOES IT WORK EXACTLY? LET S LOOK IN MORE DETAIL 1. INDUCTION SUCK 2. COMPRESSION 3. COMBUSTION 4. THE FOUR STROKE CYCLE BUT HOW DOES IT WORK EXACTLY? WE KNOW ABOUT:- WHICH WE KNOW AS:- LET S LOOK IN MORE DETAIL 1. INDUCTION SUCK 2. COMPRESSION 3. COMBUSTION 4. EXHAUST SQUEEZE BANG BLOW Inlet valve

More information

Abstract 1. INTRODUCTION

Abstract 1. INTRODUCTION Abstract Study on Performance Characteristics of Scuderi Split Cycle Engine Sudeer Gowd Patil 1, Martin A.J. 2, Ananthesha 3 1- M.Sc. [Engg.] Student, 2-Asst. Professor, 3-Asst.Professor, Department of

More information

Heat engine. Heat engine

Heat engine. Heat engine Heat engine Device that transforms heat into work. It requires two energy reservoirs at different temperatures An energy reservoir is a part of the environment so large wrt the system that its temperature

More information

INTERNAL COMBUSTION ENGINE (SKMM 4413)

INTERNAL COMBUSTION ENGINE (SKMM 4413) INTERNAL COMBUSTION ENGINE (SKMM 4413) Dr. Mohd Farid bin Muhamad Said Room : Block P21, Level 1, Automotive Development Centre (ADC) Tel : 07-5535449 Email: mfarid@fkm.utm.my HISTORY OF ICE History of

More information

Natural Gas fuel for Internal Combustion Engine

Natural Gas fuel for Internal Combustion Engine Natural Gas fuel for Internal Combustion Engine L. Bartolucci, S. Cordiner, V. Mulone, V. Rocco University of Rome Tor Vergata Department of Industrial Engineering Outline Introduction Motivations and

More information