26cc 4.5 KWA Marine Engine
|
|
- Tobias Powers
- 5 years ago
- Views:
Transcription
1 26cc 4.5 KWA Marine Engine Thank you for purchasing your new Venom 26cc 4.5 KWA Marine Engine. Not only did you purchase a top of the line R/C Marine Engine but you have also joined the Venom Team and it s world class product line and customer service. Please fully read and understand this instruction manual BEFORE operating this product. Note: This product is not a toy and may cause serious injury if not used properly. VEN-1827
2 Specifications Basic Engine Specifications: Displacement cc Bore x Stroke - 34mm x 28mm Max HP - 4.5@12,500 RPM Idle RPM /- 150 Fuel Type - 87 Octane with Premix 2 Stroke Oil Ignition - Ikeda TDi Carburetion - Walbro WT771 with Primer Pump Net Weight kg (w/ Mount) Manual Pull Start Premix Fuel Specifications: Use 90+ Octane Unleaded Gasoline Do not use gasoline with any alcohol or ethanol added Use a high performance 2 Stroke Premix Engine Oil Mix Ratio parts Oil to 1 part Gas (20-25:1) for break-in period, 30:1 standard mixture Engine Operations -The carburetor is tuned from the factory to run but may require an adjustment due to the climate and elevation in your area. -There are three adjustments on the carburetor. The low speed needle, high speed needle and idle screw. High Speed Needle Low Speed Needle Idle Screw - 2 -
3 Engine Operations Continued -The low speed needle controls the low rpm range of the engine. -The high speed needle controls the high rpm range of the engine. -The idle screw mechanically sets the opening of the carburetor and adjusts the minimum gap for air to pass through the carburetor. In a boat application this setting is often set to the maximum opening. Standard opening of each needle as follows: High Low 1 5/8 + 1/ /4 To start the engine; 1. First be sure the correct fuel mixture has been added and the fuel tank is full. 2. Pump the priming bulb on the carburetor until you see the fuel enter the bulb. 3. Pump the priming bulb 3 more times. 4. Be sure all people and objects are clear of any rotating parts. 5. With one hand, apply firm pressure to hold the top of the engine in place and with the other hand take hold of the pull start T-handle. 6. With a fast deliberate motion, pull the T-handle quickly away from the engine but no further than 10 inches while firmly holding the engine in place. 7. Repeat as necessary until the engine either starts or shows signs of starting. 8. You may adjust the low speed needle, either open or close, to help the engine start but only in small increments of 1/8th of a turn at a time until the engine starts. 9. Repeat step 6 until the engine starts. 10. Once the engine starts return the T-handle to the rest position and remove your hands from the engine and any rotating parts. To shut the engine off press the red shut off button located on the exterior of the model or on the engine itself. It is very important not to over-stress a new engine in the first few running hours of its life. It is highly recommended that the fuel and oil mixture be made slightly more oil rich for optimum lubrication during the first 2-4 hours of operation. In addition, it is also recommended that the engine speed should be limited to about 7000rpm or about half throttle during this time. Please follow the break in schedule below. Initial running - 20:1 fuel ratio for 1hr 25:1 fuel ratio for 3hrs 30:1 fuel ratio for standard operation The engine will continue to improve in performance and will continue to break in for a short time following the initial 4hrs of operation
4 Tuning Guide There are three basic areas of adjustment on a gasoline 2 stroke engine: 1. Carburetor 2. Spark Plug 3. Gasoline to Oil Ratio Carburetor Tuning While the engine is running at idle speed you can adjust the Low Speed Needle to set a steady low RPM idle. When the engine speed is at its maximum RPM the High Speed Needle is used to adjust the optimum top speed performance. The goal is to try to tune the engine until there is smooth transition from low to high speed and back to idle with out any interruptions. To set the High Speed Needle while the engine is running there are two steps. 1. Once the engine is warmed up set the engine to full open throttle and adjust the High Speed Needle until the engine sound is clear and smooth. Now place the needle setting to 1/8th to 1/4th turn rich (Counter Clockwise, CCW). Do this within 30 seconds and allow the engine to return to idle. Monitor the engine temperature during this step. 2. Step 1 above is done without a load on the engine to get an initial setting. Now run the engine in the model and set the throttle to full open. The engine should run smooth and with full power. If not, readjust the High Speed Needle until you hear a smooth crisp exhaust note. This will be the maximum performance setting for that particular day and will require fine tuning depending on climate and location from day to day. NOTE: Always pay close attention to the engine temperature when tuning on the bench and in normal use. Maximum Operating Temperature - 250F Optimal Engine Head Temperature Range F max Maximum Engine Head Water Temperature - 212F Pro Tuner Tip Use a small aquarium water pump, extra silicone tubing and a bucket of cold tap water to keep the engine and exhaust pipe cool while testing and breaking in a new engine. The Idle Screw will set the mechanical travel of the carburetor butterfly valve which controls engine speed and response. Setting the Idle Screw and the Low Speed Needle together will control the low speed idle range of the engine. In a boat application when a clutch is not installed on the engine a higher Idle Screw setting is required and it is common for this to be adjusted to the maximum setting. Use the Low Speed Needle to make idle speed adjustments in this case. Factory Needle Settings High Speed Needle - 1 5/8 turns from closed Low Speed Needle - 1 turn from closed CCW (Counter Clockwise) = Richer mixture CW (Clockwise) = Leaner mixture (Does not apply to the Idle Screw) - 4 -
5 Tuning Guide Continued NOTE: Never over tighten the tuning needles when adjusting. This will cause damage and poor tuning ability. Spark Plug Tuning There are a few performance gains from understanding and tuning the spark plug of a gasoline engine. The basic areas of interest are the Air Gap and Color of the spark plug used. Spark Plug Air Gap - the distance between the outer electrode and inner electrode. The main issues with spark plug gaps are: narrow-gap risk: spark might be too weak/small to ignite fuel narrow-gap benefit: plug always fires on each cycle wide-gap risk: plug might not fire, or miss at high speeds wide-gap benefit: spark is strong for a clean burn A properly gapped plug will be wide enough to burn hot, but not so wide that it skips or misses at high speeds, causing that cylinder to drag, or the engine to begin to rattle. Standard Spark Plug Gap mm / in Reading the Color of the Spark Plug Normal Operating Color - exterior electrode has a very light tan color, resembles ash, the interior electrode has a clean brown color, no deposits on any surfaces. Dry or Wet Fouling - the overall appearance of the plug is black and sooty or very wet with an oily appearance. Over Heating - The plug end will appear glazed especially around the ceramic insulator Replace wet, fouled, or damaged spark plugs and try to determine the cause of the fouling. Its ok to clean a spark plug if a replacement is not available but for optimum performance the fouled plug should be replaced. The color of the plug will indicate the operating condition of the engine internally. Adjusting the carburetor and using the correct fuel mixture will usually correct the problem. Gasoline to Oil Ratios The two stroke engine relies on a delicate mixture of oil mixed in with the gasoline in order to perform at maximum performance levels. Since the oil which lubricates the engine is mixed in with the fuel it is possible to cause severe engine damage and total failure if the mixture is incorrect. Please follow these guidelines to ensure proper performance and good engine life. Fuel Ratios 20:1 Initial running - 1hr 25:1 3hrs 30:1 Standard operation 32:1 Only recommended for experienced tuners How to read the ratio of gasoline to oil: The ratio above is related to 1 US Gallon of gasoline. The more rich the ratio the closer the relationship of gasoline to oil is 1 part to 1 part (1:1). The number on the left is the amount of gasoline used. The number on the right is the amount of oil. The smaller the gasoline number, the more rich the mixture will be because there is more oil in relation to gasoline. Use high performance 2 Cycle Premix Oils that contain Castor Oil and Synthetic Lubricants commonly found at Motorcycle Dealerships, Go-Karting suppliers, Gardening and Power Tool Supply stores. Use a proper oil ratio measuring cup or container
6 Recommendations Exhaust Recommendations The Venom 26cc 4.5 KWA Marine Engine can accept a whole range of exhaust systems from tuned exhausts to silencers and various manifolds. Choose the exhaust system according to your application and follow the exhaust manufacturer s recommendations for tuning and performance guidelines. Exhaust Port Bolt Pattern - 34mm center to center, M5 thread Basic Exhaust Port Dimension mm x 11.5mm Propeller Recommendations The Venom 26cc 4.5 KWA Marine Engine will perform with a range of propellers for gas boats. The Hull design, weight and drive system will have a great influence on the choice of an optimal propeller. Some experimentation will be required to obtain the best performance possible. Propeller Diameter range mm Pitch Ratio range mm Pro Tuner Tip Experiment with multiple blade counts and pitch ratios for different conditions. A 3 blade prop will help in choppy conditions and with acceleration from corners. A two blade prop is the most efficient and will usually achieve the highest speeds, but it is sensitive to water conditions. Changing the pitch ratio will change the rpm of the engine and will have different performance benefits. Listen to the engine sound, aka note, when experimenting with propellers to find the best performance. A crisp clean sound should resonate from the engine when at full power with the correct prop. Use a GPS handheld unit mounted in the boat to compare speeds between set ups
7 Trouble Shooting Engine Does Not Start - No spark in spark plug Description Cause Fix Spark Plug 1. Wet Spark Plug Electrode Dry Electrode 2. Carbon Deposits On The Electrode Clean Spark Plug 3. Spark Plug Insulator Damage Replace Spark Plug 4. Improper Spark Gap Adjust To mm 5. Burned Out Electrode Replace Spark Plug Magneto 1. Ignition Coil Inside Failure Replace Spark Plug 2. Damaged Cable Sheath or Disconnected Cable Replace Or Repair Switch 1. Switch Is Off Turn On Switch 2. Switch Failure Replace Switch 3. Primary Wiring Is Grounded Repair Engine Does Not Start - Sparks appear in the spark plug Description Cause Fix 1. Too much Fuel In Engine Drain Excess Fuel from Engine Compression & Fueling Is 2. Fuel too Rich Adjust Carburetor Normal 3. Flooded Carb Adjust Carburetor or Replace 4. Poor Fuel Quality Exchange with Proper Fuel Fueling Normal 1. Worn Out Cylinder, Piston, or Piston Ring Replace Cylinder & Piston Set But Poor Compression 2. Gas Leakage from Cylinder & Crank Case Gasket Apply Liquid Gasket & Reassemble 1. Choked Breather Air Hole Clean Breather No Fuel 2. Clogged Carburetor Clean Carburetor Supply 3. Fuel Lines Improperly Installed Check Fuel Lines Lack of Power or Poor Performance Description Cause Fix 1. Air Leak in Fuel System Check Connections Compression Is Normal w/ 2. Air Leak at Intake Tube Joint or Carburetor Joint Replace Gasket or Tighten Screws No Misfire 3. Water in Fuel Replace Fuel 4. Piston Seized Replace Piston & Cylinder 5. Muffler has Excessive Carbon Build-up Clean Muffler Overheating 1. Carburetor Set too Lean Adjust Carburetor 2. Poor Fuel Quality Replace Fuel 3. Excessive Carbon Build-Up in the Combustion Chamber Clean Combustion Chamber 4. Spark Plug Electrode Red Hot Thoroughly Clean, Adjust Spark Gap [ ( in)] Others 1. Over Loading Reduce Load - 7 -
8 Warranty VENOM LIMITED WARRANTY: Venom warrants this product to be free of material and workmanship defects when new. If a component is defective or was not correctly made, Venom will, at its sole discretion, repair or replace it free of charge within 90 days from date of purchase. If you believe a defect became evident only after operation, please contact us to discuss the situation. A dated and itemized sales receipt must accompany any product returned for warranty work. Before returning any product, please contact Venom Customer Service at to receive a Return Merchandise Authorization Number (RMA#). GUARANTEE: We guarantee this product to be free of manufacturing faults and material defects. This product has been checked and adjusted individually before leaving the manufacturer. Please contact your local retailer for replacement parts and technical support or contact Venom Customer Service at or customerservice@venom-group.com. Copyright 2008 by Venom Warning WARNING: This product is not a toy. It is not recommended for children under 14 years. Minors should be accompanied by an adult when using. This product is a precision machine that requires proper assembly and setup to avoid accidents. Failure to take caution when operating this product may result in serious injury or property damage. It is the owner s responsibility to operate this product in a safe manner. Venom and its affiliates, successors, heirs, and assigns are not responsible in any way for any and all bodily injury(s) and/or property damage that may occur from the use of or caused by in any way this product or its parts. CALIFORNIA PROPOSITION 65 HEALTH RISK WARNING: This product contains a chemical or chemicals known to the state of California to cause cancer, birth defects, or other reproductive harm. This (these) chemical(s) may be harmful to your health. Do not place hands in mouth after handling this product. Do not place this product in mouth. Wash hands with soap and water immediately after handling this product
9 Parts List VEN-1828 Crankcase Assembly - KWA VEN-1829 Crank Shaft Assembly - KWA VEN cc Cylinder - KWA VEN-1831 Cylinder Gasket - KWA VEN cc Piston - KWA VEN-1833 Piston Ring VEN-1834 Piston Pin VEN-1835 Snap Ring VEN-1836 Positioning Washer VEN-1837 Need Bearing VEN-1838 Intake Gasket VEN-1839 Bolt (M5*25) - KWA VEN-1840 Exhaust Gasket - KWA VEN-1841 Water Jacket - KWA VEN-1842 Carburetor VEN-1843 Recoil Assembly VEN-1844 Flywheel - KWA VEN-1845 Ignition Coil -KWA VEN-1846 Kill Switch Set - KWA VEN-1847 Frame Set - KWA VEN-1848 Mount Assembly - KWA VEN-1849 Spark Plug - 9 -
10 Notes
11 Customer Service Venom Group International United States of America 600 West Buckles Road Hayden, ID Australia P.O. Box 7325 Alexandria NSW 2015, Australia
PF-4000, PF-4010, PF-4210 MULTI-PURPOSE ENGINE
PF-4000, PF-4010, PF-4210 MULTI-PURPOSE ENGINE Date 09-26-01 Supplier To The Outdoor Power Equipment Industry ISM, Inc. 1028 4 th Street SW Auburn, WA 98001 Phone: (253) 333-1200 Fax: (253) 333-1212 WWW.TANAKA-USA.COM
More informationGP 123. Great Power Model Engines
Great Power Model Engines www.gp-engine.com.tw GP 123 Displacement: 123C.C Output: 13hp Bore: 46.5mm Weight: 2300g RPM Range: 1000~7200 Recommend Gasoline Octane Number: 89~92 (R+M)/2) Warranty: 2 years
More informationOperation and Maintenance Instructions for the RAPTOR 178
WWW.SKYTOY.COM Operation and Maintenance Instructions for the RAPTOR 178 See www.skytoy.com for updates and service bulletins. 2/1/2011 1. Parts Schematic:... 3 2. Muffler Assembly Diagram:... 4 3. Muffler
More informationCOLT 2310, 2510, AND 2712 COM PACT TRACTORS CHAPTER 9 TROUBLESHOOTING AND ANALYSIS
COLT 2310, 2510, AND 2712 COM PACT TRACTORS CHAPTER 9 TROUBLESHOOTING AND ANALYSIS 9-A-1 UPON RECEIVING ANENGINE FORRE- PAIR. Learn the history of the unit from the customer. While the customer is present
More informationOWNER'S MANUAL Model: G320PUM for radio control Boat Model code:
115650026 (404) OWNER'S MANUAL Model: G320PUM for radio control Boat Model code: 967289101 WARNING This engine is designed for radio controlled boat use. When replacing parts, use only parts which have
More informationTypical Install Instructions
Typical Install Instructions Read & understand all steps of these instructions before beginning this installation. WEBER Conversion Kit, VW T-1/2, up to 1835cc 32 / 36 DFEV Weber Carburetor These instructions
More informationInstructions for SAITO FA-200R3 (AAC) 4-Stroke Engine
Instructions for SAITO FA-200R3 (AAC) 4-Stroke Engine We would like to express our sincere thanks for your purchase of the SAITO FA-200R3 engine. Please read our instructions carefully and treat your engine
More informationWORKSHOP MANUAL. 63,4 cm³ chainsaws
WORKSHOP MANUAL General failures analysis Suggested tools I. Emak tool kit II. Compression tester: to check thermal group III. Electronic tachometer: for 2 and 4 stroke engines, measurement range from
More informationTP300 INDUSTRIAL TRASH PUMP OPERATOR S MANUAL
TP300 INDUSTRIAL TRASH PUMP OPERATOR S MANUAL IT IS EXTREMELY IMPORTANT TO READ AND UNDERSTAND THE ENTIRE CONTENTS OF THIS OPERATOR S MANUAL BEFORE ATTEMPTING TO OPERATE THE PRODUCT. THIS EQUIPMENT IS
More information2007 HOP-UP INFORMATION. Foreword
2007 HOP-UP INFORMTION Foreword This manual contains the hop-up information for RM series of European specification and is intended to allow the standard model to achieve its maximum performance potential.
More informationInstruction Manual SPE-26CC
Instruction Manual SPE-26CC 1 Safety Precautions This engine is for experienced flyers only and could cause serious harm if used incorrectly. Always take care when running large gas engines. Read this
More informationPlease read the Owner s Manual thoroughly before starting your engine for the first time.
2 ::: Introductionn r Thank you for purchasing Reedy s 121VS Nitro Engine. Designed in-house by our esteemed engineering staff, this engine is produced using state-of-the-art materials and high-tech manufacturing
More information5. FUEL SYSTEM 5-0 FUEL SYSTEM MXU 250R/300R
5 FUEL SYSTEM 5 SERVICE INFORMATION------------------------------------------------ 5-2 TROUBLESHOOTING----------------------------------------------------- 5-3 FUEL TANK -----------------------------------------------------------------
More informationINDEX TECHNICAL SPECIFICATIONS 2 SPECIAL TOOLS 3-4 PERIODIC MAINTENANCE 5 LUBRICANTS 6 TROUBLESHOOTING 7-14 TIGHTENING TORQUE TABLE 15
INDEX TECHNICAL SPECIFICATIONS 2 SPECIAL TOOLS 3-4 PERIODIC MAINTENANCE 5 LUBRICANTS 6 TROUBLESHOOTING 7-14 TIGHTENING TORQUE TABLE 15 ENGINE DISASSEMBLY 16-24 ENGINE REASSEMBLY 25-37 SPECIAL 3-SHOE CLUTCH
More informationSTRX-9 100% TAKE CONTROL INSTRUCTION MANUAL READY-TO-RUN. w/ Adult Supervision
STRX-9 w/ Adult Supervision INSTRUCTION MANUAL 18005 100% READY-TO-RUN TAKE CONTROL Index Included Items Important Notes Battery Installation Charging Instructions Transmitter/Receiver Binding Basic Controls
More informationPORTABLE TRASH PUMPS MDP200
PORTABLE TRASH PUMPS MDP200 OPERATING & PARTS MANUAL INTRODUCTION This manual provides information and procedures to safely operate and maintain the engine and pump. For your own safety and protection
More informationPORTABLE TRASH PUMPS MTP200 MTP300 MTP400
PORTABLE TRASH PUMPS MTP200 MTP300 MTP400 OPERATING & PARTS MANUAL INTRODUCTION This manual provides information and procedures to safely operate and maintain the engine and pump. For your own safety and
More informationNOTE: "D" is for diameter, and "T" is for thread.
Rossi has been making engines since 1960. The factory incorporates the best Swiss CNC machinery that manufactures engines with the most precise tolerances from the best quality materials producing the
More informationCarburetor Instructions
Carburetor Instructions for HUDSON SUPER SIX ESSEX SIX CYLINDER Hudson Motor Car Co. DETROIT, U.S.A. Carburetor The carburetor is a device for metering correct amounts of fuel and air for the various
More informationWORKSHOP MANUAL. Chainsaw GS35 GS350 MT350 MT3500
WORKSHOP MANUAL Chainsaw GS35 GS350 MT350 MT3500 General failures analysis Suggested tools I. Emak tool kit II. Compression tester: to check thermal group III. Electronic tachometer: for 2 and 4 stroke
More informationOWNER S MANUAL G620PU-1 MODEL: G620PU WARNING 848H5693A3 (208)
848H5693A3 (208) OWNER S MANUAL MODEL: G620PU G620PU-1 WARNING Do not modify any parts of the engine. This engine is designed to be used to Radio controlled products. In case any modification by customer,
More information4. FUEL SYSTEM CK 1 4-0
4 4 4-0 SERVICE INFORMATION... 4-1 FLOAT LEVEL INSPECTION... 4-5 TROUBLESHOOTING... 4-2 CARBURETOR INSTALLATION... 4-6 THROTTLE VALVE DISASSEMBLY... 4-3 THROTTLE VALVE ASSEMBLY... 4-6 CARBURETOR REMOVAL...
More information5. FUEL SYSTEM FUEL SYSTEM 5-0
5 FUEL SYSTEM 5-0 SERVICE INFORMATION GENERAL INSTRUCTIONS SERVICE INFORMATION...5-1 CARBURETOR INSTALLATION...5-9 TROUBLESHOOTING...5-1 PILOT SCREW ADJUSTMENT...5-10 CARBURETOR REMOVAL...5-2 AUTO BYSTARTER...5-3
More informationCRRCpro GP26R Gasoline Engine
CRRCpro GP26R Gasoline Engine Thank you very much for buying this engine. Hope it will bring you a good happy time. In order to get a good operation, please read the instruction in detail as below. I Parameter
More information4. FUEL SYSTEM 4-0 FUEL SYSTEM NEXXON 50
4 FUEL SYSTEM SERVICE INFORMATION ------------------------------------------------ 4-2 TROUBLESHOOTING----------------------------------------------------- 4-3 AIR CLEANER REMOVAL -----------------------------------------------
More informationINSTRUCTION MANUAL GASOLINE BRUSH CUTTER TR L. 42.7cc. 1.3 kw. 450 mm. Note : Read and carefully before using this machine
INSTRUCTION MANUAL GASOLINE BRUSH CUTTER TR15142 Note : Read and carefully before using this machine 42.7cc 1.3 kw 450 mm 18" 0.70 L MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION This symbol accompanied
More informationTECHNICAL DATA. COMPRESSION RATUI 9,5/1 WEIGHT ready to fly CONSUMPTION at 5400RPM 5,6litres/h POWER at 6200RPM
VICTOR 1 SUPER This handbook aims to bring to the attention of key technical, functional and maintenance of your motor VICTOR 1. Read carefully the following pages, will be synonymous with safety, reliability
More information20. TROUBLESHOOTING ENGINE DOES NOT START OR IS HARD TO START XL200
20. ENGINE DOES NOT START OR IS HARD TO START 20-1 ENGINE LACKS POWER 20-2 POOR PERFORMANCE AT LOW AND IDLE SPEED 20-3 POOR PERFORMANCE AT HIGH SPEED 20-4 POOR HANDLING 20-4 ENGINE DOES NOT START OR IS
More informationIMPORTANT: Read this manual fully before assembly and use and observe all safety rules and operating instructions
PETROL ENGINE Model: MLR52 IMPORTANT: Read this manual fully before assembly and use and observe all safety rules and operating instructions Contents Technical Specification 2 Safety 3 Starting 5 Running
More informationDLA56 USER MANUAL TOPLEVEL GASOLINE ENGINE. Manufactured by FeiaoModel
DLA56 TOPLEVEL GASOLINE ENGINE USER MANUAL Manufactured by FeiaoModel User Manual Thanks for purchasing DLA series engines,pls read all of the instructions below before starting your engine, especially
More informationEME 60 Gasoline Engine User Manual
EME 60 Gasoline Engine User Manual Eagle Master Engine EME 60 User Manual 1 SAFETY INSTRUCTIONS Thank you for purchasing EME 60 gasoline Engine. We at EME always strive to product reliable engines that
More informationElectrics. What you will learn. Things you need before you start. Materials. Tools. When you have finished this module, you should be able to:
Student Electrics What you will learn When you have finished this module, you should be able to: Choose the right spark plug for your engine Clean a spark plug and set the gap Check and clean the HT lead
More informationOWNER S MANUAL G620PU-1 MODEL: G620PU WARNING 848H4893A3 (704)
848H4893A3 (704) OWNER S MANUAL MODEL: G620PU G620PU-1 WARNING Do not modify any parts of the engine. This engine is designed to be used to Radio controlled products. In case any modification by customer,
More informationOWNER S SERVICE MANUAL
115 50 57-26 (206) OWNER S SERVICE MANUAL MODEL: G231PUM for radio control Boat G231PUH for radio control Helicopter G260PU for radio control Airplane G260PUM for radio control Boat G260PUH for radio control
More informationFUEL SYSTEM. Table of Contents. Specifications. Section 3A Fuel Delivery System. Models 6/8/9.9/10/15 CARBURETOR SPECIFICATIONS
FUEL SYSTEM Section 3A Fuel Delivery System Table of Contents Specifications............................. 3A-1 WMC Carburetor Specifications............. 3A-2 WMC Carburetor Specifications.............
More informationINSIDE YOUR HOLLEY CARBURETOR FUEL INLET SYSTEM
INSIDE YOUR HOLLEY CARBURETOR The carburetor is quite simply a fuel metering device that operates under the logical and straightforward laws of physics. It has evolved over the years from a very simple
More informationDIRECTIONS FOR USING ZDZ ENGINES
DIRECTIONS FOR USING ZDZ ENGINES (Please READ this carefuly and become FAMILIAR with these instructions before using the engine) ZDZ two-stroke gasoline engines are intended for large models and offer
More informationSERVICE BULLETIN REFERENCES 1983
J a I) SERVICE BULLETIN REFERENCES 1983 19.35 TROUBLE SHOOTING Engine Won t Start or Hard Starting Possible Cause ALL MODELS No fuel in tank. Fuel valve off. Insufficient or excessive priming. Spark plug
More informationTILLOTSON LTD., CLASH INDUSTRIAL ESTATE, TRALEE, CO. KERRY, IRELAND PHONE: FAX:
TILLOTSON LTD., CLASH INDUSTRIAL ESTATE, TRALEE, CO. KERRY, IRELAND PHONE: +353 66 7121911 FAX: +353 66 7124503 e-mail: sales@tillotson.ie SERIES SERVICE MANUAL INTRODUCTION The gasoline engine industry
More informationTel: , FAX: ,
DIRECTIONS FOR USING ZDZ ENGINES (Please READ this carefuly and become FAMILIAR with these instructions before using the engine) ZDZ two-stroke gasoline engines are intended for large models and offer
More informationKING CANADA 950W PORTABLE GENERATOR MODEL: KCG-951G INSTRUCTION MANUAL COPYRIGHT 2011 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
KING CANADA 950W PORTABLE GENERATOR MODEL: KCG-951G INSTRUCTION MANUAL COPYRIGHT 2011 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC. WARRANTY & SERVICE INFORMATION 1-YEAR LIMITED WARRANTY FOR THIS 950W
More informationFebruary 26, ch.12.notebook. Ch. 12. Preventative Maintenance and Troubleshooting. Feb 23 5:03 PM
Ch. 12 Preventative Maintenance and Troubleshooting Feb 23 5:03 PM 1 Why PM? preventive maintenance certain maintenance tasks must be performed regularly to keep an engine working properly helps premature
More informationCH. 48 ENGINE MECHANICAL PROBLEMS TEST
TERRY FOX AUTOMOTIVE CH. 48 ENGINE MECHANICAL PROBLEMS TEST WHEN YOU ARE DONE THIS TEST GUESS WHAT YOU THINK YOU WILL RECEIVE FOR A MARK BELOW. IF YOU ARE WITHIN 2 MARKS YOU WILL RECEIVE 2 BONUS MARKS.
More informationCiscomotors C-Max All types of models
Ciscomotors C-Max All types of models SiMPLIFIED MAINTENANCE MANUAL All information in this publication is based on latest specification s product available at the time of approval for printing. CISCOMOTORS
More informationArrow Shark 2015 E-Starter V4 Owner Manual
Arrow Shark 2015 E-Starter V4 Owner Manual The Arrow Shark E-Starter V3 has successfully been available in the market for over three years now. During that time, we have never stopped seeking ways to improve
More informationSECTION 6 2 SERVICE PROCEDURES AND SPECIFICATIONS. Engine. Specifications
SERVICE PROCEDURES AND SPECIFICATIONS Engine SECTION 6 2 Specifications........................................... 170 Fuel.................................................... 172 Facts about engine oil
More informationService Instruction ENGINE COMPONENTS, INC.
Title: Service Instruction S.I. No.: 89-5-1 Page: 1 of 5 Issued: 05/05/89 Revision: 1 (09/01/01) Technical Portions of FAA DER Approved. FAILURE OF ENGINE TO START 27 points 1. Lack of fuel 2. Ignition
More informationSECTION 6 2 SERVICE PROCEDURES AND SPECIFICATIONS. Engine. Specifications
SERVICE PROCEDURES AND SPECIFICATIONS Engine SECTION 6 2 Specifications........................................... 162 Fuel.................................................... 164 Facts about engine oil
More informationOWNER'S MANUAL. Model: G300PUM for radio control Boat WARNING (1808)
114 06 37-26 (1808) OWNER'S MANUAL Model: G300PUM for radio control Boat WARNING This engine is designed for radio controlled boat use. When replacing parts, use only parts which have been certified by
More informationWorkshop Manual. GZ25N Applicable Model Name:
S4810-0006 R Workshop Manual STRATO CHARGED ENGINE GZ25N Applicable Model Name: 1. Brushcutters BCZ2500S/BCZ2500SU 2. Long Reach Trimmer LRTZ2500 3. Short Reach Trimmer SRTZ2500 4. Pole Saw PSZ2500 5.
More informationIMPORTANT INFORMATION
Table of Contents IMPORTANT INFORMATION Section 1B - Maintenance MAINTENANCE 1 B Specifications........................... 1B-1 Special Tools........................... 1B-2 Mercury/Quicksilver Lubricants
More informationMcCULLOCH. Stroke. 30 mm (1.2 in.) 30 mm (1.2 in.) 30 mm (1.2 in.) 30 mm (1.2 in.)
SERVICE MANUAL Model Eager Beaver 2010, Mac 3210 Silver Eagle 2012 Eager Beaver 2014, Mac 3214, Silver Eagle 2014 Eager Beaver 2016, Mac 3216, Silver Eagle 2016 Bore Stroke DispL (2.1 cu. in.) (2.1CU.
More informationSINGLE STAGE SNOW ENGINE SERVICE MANUAL
RESIDENTIAL PRODUCTS SINGLE STAGE SNOW ENGINE SERVICE MANUAL LC154FS / LC154FDS (87cc) About this Manual This service manual was written expressly for Toro service technicians. The Toro Company has made
More information5. FUEL SYSTEM 5-0 FUEL SYSTEM UXV 500
5 FUEL SYSTEM 5 SERVICE INFORMATION------------------------------------------------ 5-02 TROUBLESHOOTING----------------------------------------------------- 5-03 FUEL TANK -----------------------------------------------------------------
More informationOWNER'S MANUAL Model: G240RC/G270RC/G290RC Model code: X (G240RC) Model code: X (G270RC) Model code: (G290RC)
OWNER'S MANUAL Model: G240RC/G270RC/G290RC Model code: X374323111 (G240RC) Model code: X374326111 (G270RC) Model code: 966669901 (G290RC) 115 39 20-26 (007) Thank you for using ZENOAH ENGINE. Please read
More informationRacing Performance Catalog & Reference Guide Model/Type:
Version 4/08 Racing Performance Catalog & Reference Guide Model/Type: 124435 8105-01 Table of Contents SAFETY... 1 WORLD FORMULA General Specs...3 Special Tools...3 Torque Specs...3 Racing Specifics...3
More informationOWNER'S MANUAL Model: G320RC Model code:
115 64 99-26 (403) OWNER'S MANUAL Model: G320RC Model code: 967289001 Thank you for using ZENOAH ENGINE. Please read this Owner s Manual thoroughly before operating and use the engine correctly according
More informationAG-HA-2500N GASOLINE GENERATOR
AG-HA-2500N GASOLINE GENERATOR OWNER S MANUAL BEFORE OPERATING THIS EQUIPMENT PLEASE READ THESE INSTRUCTIONS CAREFULLY (I)WARNING 1. Read the operator s instruction manual. 2. Attention! Exhaust gases
More informationOWNER'S MANUAL Model: G240RC/G270RC Model code: X (G240RC) Model code: X (G270RC)
848ER893A0 (804) OWNER'S MANUAL Model: G240RC/G270RC Model code: X374323111 (G240RC) Model code: X374326111 (G270RC) Thank you for using ZENOAH ENGINE. Please read this Owner s Manual thoroughly before
More information00-36A-04 CS-350T, CS-350TES, CS-350WES 1
00-36A-04,, 1 0 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice. All specifications,
More informationCARTER DOWNDRAFT CARBURETOR Terraplane All Models. Technical Information
CARTER DOWNDRAFT CARBURETOR 1934 Terraplane All Models Technical Information . Carter W-1 Downdraft Carburetors 1934 Terraplane Challenger, Model KS NOTE: Terraplane Models. Carburetor fitted with Anti-
More informationEngine Does Not Start or Is Hard to Start Cause of Trouble. 1. Open the drain screw, and check Fuel not supplied (1) Fuel tank empty
20. Engine Does Not Start or Is Hard to Start 20-1 Engine Output Insufficient 20-2 Poor Performance at Low Speed and Idling 20-3 Poor Performance at High Speed 20-3 Unsatisfactory Operation 20-4 Fuel Gauge
More informationCounter-clockwise, view to output shaft Mixture 1:50, 2-stroke-oil, fuel min. 95 octane (RON)
HIRTH 2703 Carburated - 55 hp The 2703 V is an air cooled, piston controlled 2-cylinder-inline-2-stroke engine with one or two carburetors and Nikasil coated cylinders. It has one of the highest power
More informationTILLOTSON LTD., CLASH INDUSTRIAL ESTATE, TRALEE, CO. KERRY, IRELAND PHONE: FAX:
TILLOTSON LTD., CLASH INDUSTRIAL ESTATE, TRALEE, CO. KERRY, IRELAND PHONE: +353 66 7121911 FAX: +353 66 7124503 e-mail: sales@tillotson.ie HR SERIES SERVICE MANUAL INTRODUCTION Tillotson has developed
More informationA. Perform a vacuum gauge test to determine engine condition and performance.
ENGINE REPAIR UNIT 2: ENGINE DIAGNOSIS, REMOVAL, AND INSTALLATION LESSON 2: ENGINE DIAGNOSTIC TESTS NOTE: Testing the engine s mechanical condition is required when the cause of a problem is not located
More informationSERVICE DATA CHAIN SAW ECHO: CS-500ES STAGE MODEL. (Serial number : and after) CONTENTS INTRODUCTION
01-50D-01 1 0 SERVICE DATA CHAIN SAW ECHO: STAGE MODEL (Serial number : 37000001 and after) INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data,
More informationWEBER CARBURETOR TROUBLESHOOTING GUIDE
This guide is to help pinpoint problems by diagnosing engine symptoms associated with specific vehicle operating conditions. The chart will guide you step by step to help correct these problems. For successful
More informationTillotson Tc3A Carburator
Tillotson Tc3A Carburator 176 FUEL SYSTEMS - 5B-11 CENTER BOWL TYPE CARBURETOR Removal 1. Remove front cowl cover and wrap-around cowl. 2. Remove swivel link from lower carburetor. (Figure 2) 3. Loosen
More information2005 Manufactured exclusively for Horizon Hobby, Inc
2005 Manufactured exclusively for Horizon Hobby, Inc. www.horizonhobby.com 800-535-5551 7795 Evolution Engines 26GT/35GT USER GUIDE Before using this engine, please read these instructions carefully. Introduction
More informationOVERHEAD VALVE SIDE VALVE DIESEL ROBIN AMERICA, INC. ROBIN TO WISCONSIN ROBIN ENGINE MODEL CROSS REFERENCE LIST ROBIN
ROBIN AMERICA, INC. ROBIN TO WISCONSIN ROBIN ENGINE MODEL CROSS REFERENCE LIST ROBIN WISCONSIN ROBIN SIDE VALVE EY08 EY15 EY 15V EY20 EY2OV EY23 EY28 EY3 5 EY40 - EY45V EY2 1 EY44 EY 18-3 EY25 EY27 W 1-080
More informationReproduction. Not for. Briggsracing.com. CORPORATION Briggs & Stratton Corporation MS /08
Briggsracing.com MS-5702-4/08 BRIGGS&STRATTON CORPORATION Post office box 702 Milwaukee, WI 53201 USA 414 259 5333 2008 Briggs & Stratton Corporation Version 4/08 Racing Performance Catalog & Reference
More informationVacuum Readings for Tuning and Diagnosis
Vacuum Readings for Tuning and Diagnosis -Henry P. Olsen Once you learn to properly interpret its readings, a vacuum gauge can be one of the most useful tools in your toolbox. 22 FEATURE Some people consider
More informationIGNITION COIL - 2.4L SPARK PLUG
TJ IGNITION CONTROL 8I - 13 IGNITION COIL - 2.4L DESCRIPTION - 2.4L The coil assembly consists of 2 different coils molded together. The assembly is mounted to the top of the engine (Fig. 21). REMOVAL
More informationGeneral Power Products
Portable Electric Generator Owners Manual MODEL: APP 6000 General Power Products IMPORTANT Please make certain the person who uses this Generator thoroughly reads these instructions and all other instructions
More informationInstruction Model 18537
Instruction 738-556 Model 18537 LIMITED WARRANTY H. D. Hudson Manufacturing Company warrants to the original purchaser only that this product will continue to function as intended if used in accordance
More informationTWO STAGE SNOW ENGINE SERVICE MANUAL
RESIDENTIAL PRODUCTS TWO STAGE SNOW ENGINE SERVICE MANUAL LC175FDS (265cc) LC180FDS (302cc) About this Manual This service manual was written expressly for Toro service technicians. The Toro Company has
More informationVictor Jr. Plate Upgrade Kits for Square Flange and Dominator Carburetors Kit #70024 and #70025 INSTALLATION INSTRUCTIONS
Victor Jr. Plate Upgrade Kits for Square Flange and Dominator Carburetors Kit #70024 and #70025 INSTALLATION INSTRUCTIONS Please study these instructions carefully before installing your new Edelbrock
More informationCounter-clockwise, view to output shaft Mixture 1:50, 2-stroke-oil, fuel min. 95 octane (RON)
HIRTH 2703 Carburated - 55 hp The 2703 V is an air cooled, piston controlled 2-cylinder-inline-2-stroke engine with one or two carburetors and Nikasil coated cylinders. It has one of the highest power
More informationTILLOTSON LTD., CLASH INDUSTRIAL ESTATE, TRALEE, CO. KERRY, IRELAND PHONE: FAX:
TILLOTSON LTD., CLASH INDUSTRIAL ESTATE, TRALEE, CO. KERRY, IRELAND PHONE: +353 66 7121911 FAX: +353 66 7124503 e-mail: sales@tillotson.ie HU SERIES SERVICE MANUAL INTRODUCTION To keep apace of new market
More informationName Date. True-False. Multiple Choice
Name Date True-False T F 1. Oil film thickness increases with an increase in oil temperature. T F 2. Displacement is the volume that a piston displaces in an engine when it travels from top dead center
More informationTroubleshooting A Vintage Distributor Ignition System
Troubleshooting A Vintage Distributor Ignition System -Henry P. Olsen When the owners of vintage carburetor- and distributor-equipped vehicles see that a shop has a big-box engine analyzer, they believe
More informationSPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES
ENGINE FD620D, K SERIES SPECIFICATIONS SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking
More informationTECH INFORMATION EMPI D Performance 2-Barrel Carburetor
TECH INFORMATION EMPI D Performance 2-Barrel Carburetor The New EMPI D 2-Barrel Performance Carburetor.Built specifically for the VW Aftermarket. With all the features that you have asked for More Progression
More informationINDEX INTRODUCTION. Reference No L-01 REVISED:
12-21L-01 1 1 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice. All specifications
More informationSERVICE DATA CHAIN SAW CS-450. (Serial number : and after) CONTENTS INTRODUCTION. Reference No B-01 REVISED: ISSUED:
01-45B-01 1 0 SERVICE DATA CHAIN SAW (Serial number : 36000001 and after) INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and
More information00-33A-01 CS-330T, CS-360T 1
00-33A-01 CS-330T, CS-360T 1 0 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice.
More informationOperating instructions
Operating instructions MVVS 116 NP No: 3010NP Before using the engine, please read these instructions carefully. Congratulations on choosing the gas engine MVVS 116cc. MVVS 116cc has been designed and
More informationSERVICE DATA CHAIN SAW ECHO: CS-352ES STAGE MODEL. (Serial number : and after) CONTENTS INTRODUCTION
01-34D-01 1 0 SERVICE DATA CHAIN SAW ECHO: STAGE MODEL (Serial number : 37000001 and after) INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data,
More information8500M INDUSTRIAL GASOLINE GENERATOR OPERATOR S MANUAL
8500M INDUSTRIAL GASOLINE GENERATOR OPERATOR S MANUAL IT IS EXTREMELY IMPORTANT TO READ AND UNDERSTAND THE ENTIRE CONTENTS OF THIS OPERATOR S MANUAL BEFORE ATTEMPTING TO OPERATE THE PRODUCT. THIS EQUIPMENT
More informationS&S Cycle, Inc County Highway G Box 215 Viola, Wisconsin Phone: Fax:
Instruction Sheet 51-1010 Revised 5-1-02 Copyright, 2002 by S&S Cycle, Inc. All rights reserved. Printed in the U.S.A. S&S Cycle, Inc. 14025 County Highway G Box 215 Viola, Wisconsin 54664 Phone: 608-627-1497
More informationMODELS 3100,3130,3160, 1300, 1330,1360 EXHAUST SYSTEM
MODELS 3100,3130,3160, 1300, 1330,1360 EXHAUST SYSTEM WALBRO CARBURETOR "WA" SERIES MUFFLER REMOVAL CARBURETOR REMOVAL The muffler assembly should beremoved periodically to inspect for excessive carbon
More informationVentilation System Before Starting
How Long Should You Crank An Engine Ventilation System Before Starting Any electric start motor should be able to be started using a rope, (unless the motor Someone may have "worked' on it before and flopped
More informationOwner s/operator s Manual
Water Pump MP2533E2 Owner s/operator s Manual Completely read and understand this manual before using this product. Foreword This Owner s/ Operator s Manual is designed to familiarize the operator with
More informationSERVICE DATA CHAIN SAW ECHO: CS-280WES STAGE MODEL. (Serial number : and after) CONTENTS INTRODUCTION. Reference No B-00 ISSUED:
00-27B-00 1 0 SERVICE DATA CHAIN SAW ECHO: STAGE MODEL (Serial number : 37000001 and after) INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data,
More informationBREAK-IN BENCH FOR ALL 1/8 & 1/10 NITRO ENGINES INSTRUCTION MANUAL
BREAK-IN BENCH FOR ALL 1/8 & 1/10 NITRO ENGINES INSTRUCTION MANUAL CONTENTS HUDY Engine Break-In Bench INTRODUCTION...2 SAFETY FIRST...3 EXPLODED VIEW...4 EQUIPMENT REQUIRED FOR OPERATION...5 FACTORY PRE-ASSEMBLED...7
More information9000RC INDUSTRIAL GASOLINE GENERATOR OPERATOR S MANUAL
9000RC INDUSTRIAL GASOLINE GENERATOR OPERATOR S MANUAL IT IS EXTREMELY IMPORTANT TO READ AND UNDERSTAND THE ENTIRE CONTENTS OF THIS OPERATOR S MANUAL BEFORE ATTEMPTING TO OPERATE THE PRODUCT. THIS EQUIPMENT
More informationReady to Run Owner s Manual (Online Version)
Ready to Run Owner s Manual (Online Version) Thank you for choosing BONZÍ SPORTS. Please read the following instructions carefully before attempting to operate your Bonzi boat. Failure to do so could result
More informationNo part of this publication may be reproduced without written permission.
Thank you for purchasing a Honda generator. This manual covers operation and maintenance of the EB3000 and EB4000 generators. All information in this publication is based on the latest product information
More informationУрал) - Dnepr (Днепр) Russian Motorcycle Carburetors
Ural (Урал( Урал) - Dnepr (Днепр) Russian Motorcycle Carburetors Part 8A: Adjustment and Overhaul of the Pekar K-65 Carburetors (see also Part 8-8 K-65 Carburetor and Part 8B- Setting Up K-65 K Carbs)
More informationAccident Prevention Program
Accident Prevention Program Part I ENGINE OPERATION FOR PILOTS by Teledyne Continental Motors SAFE ENGINE OPERATION INCLUDES: Proper Pre-Flight Use the correct amount and grade of aviation gasoline. Never
More information