Experimental Investigation of Performanec of Single Cylinder 4s Diesel Engine Using Dual Vegetable Oil Blended

Transcription

1 ISSN : , Vol. 4, Issue 3( Version 1, March 2014, pp RESEARCH ARTICLE OPEN ACCESS Experimental Investigation of Performanec of Single Cylinder 4s Diesel Engine Using Dual Vegetable Oil Blended Prof. C. S. Koli*, Prof. Ram Bansal*, Amit Agrawal**, Ashish Agrawal** *Asst. Prof. Mech. Engg. Dept. SRCEM, Banmore ** Research Scholar Mech. Dept. SRCEM, Banmore ABSTRACT Over the last two decades there has been a tremendous increase in the number of automobiles and a corresponding increase in the fuel price. In this regard, alternative fuels like vegetable oils play a major role. Use of pure vegetable oil in diesel engines causes some problems due to their high viscosity compared with diesel fuel. To solve the problems due to high viscosity various techniques are used. One such technique is fuel blending. This paper investigated the performance parameters of dual vegetable oil blends (mixture of Mustard oil and Palm oil with diesel on a stationary single cylinder, four stroke direct injection compression ignition engine. The blends of BB 10 (combination of Diesel 90% by volume, Mustard oil 5% by volume and Palm oil 5% by volume and blends of BB 20 (combination of Diesel 80% by volume, Mustard oil 10% by volume and Palm oil 10% by volume gave better brake thermal efficiency, lower total fuel consumption and lower brake specific fuel consumption than other blends (BB 30, BB 40 and BB 50. Key word: Diesel engine, Mustard oil, Palm oil, Performance parameters, Specific gravity, Flash point, Fire point. I. INTRODUCTION Vegetable oils have some advantages. They are renewable, easily available in the rural areas, have high cetane number, heat release rate is similar to diesel, it s emission rate is relatively low to be used in Compression Ignition engines with simple modifications and can be easily blended with diesel. Jatropha oil, sesame oil, coconut oil, sunflower oil, neem oil, mahua oil, peanut oil, palm oil, rubber seed oil, cotton seed oil and rape seed oil are some of the vegetable oils that have been tried as fuel in Internal combustion engines. The use of vegetable oils as an alternative fuel for diesel engines dates back to around a century. Due to rapid decline of crude oil reserve and increase in price, the use of vegetable oils is again prompted in many countries. Depending upon soil condition and climate, different nations are looking for different vegetable oils for example, soybean oil in U.S.A., Mustard oil in Bangladesh, rapeseed and sunflower oil in Europe, palm oil in Malaysia and Indonesia, coconut oils in Philippines are being considered to substitute of diesel fuel. II. OBJECTIVE The aim of the present study is to evaluate the performance using different blends of palm oil and mustard oil with diesel in a CI engine. The following are the major objectives to fulfil the aim of present study. 1. Extraction of palm oil from palm seeds. 2. Determination of physical properties of palm oil, mustard oil and diesel. 3. Study of effect of dilution on properties of blending of palm oil and mustard oil with diesel. 4. Performance evaluation of Diesel engine using different blends of palm oil and mustard oil with diesel. III. EXPERIMENTAL SETUP ENGINE: The engine is water cooled single cylinder four stroke constant speed diesel engine 5 H.P Make Kirloskar. Figure 1 : Setup of single cylinder four stroke diesel engine 78 P a g e

2 ISSN : , Vol. 4, Issue 3( Version 1, March 2014, pp Rope Brake Dynamometer: A rope brake dynamometer is supplied with the engine coupled with the flywheel of engine. Load indicator: It indicates the load in kg range 0-20 kg Make Harrison. IV. BLENDED OILS WITH DIFFERENT PERCENT S OF DIESEL, MUSTARD OIL AND PALM OIL M.S. Base Frame: The engine and the dynamometer are mounted on a solid M.S. Channel Base Frame. Instrumentation for measuring various inputs/outputs: All instrumentation is incorporated on a control panel. The various factors to be measured are as follows: Fuel measurement: This is done by using burette which is mounted on the control panel. The fuel tank is mounted on panel. The fuel is supplied to engine using a fuel line to fuel injection system. The amount of fuel consumed is determined by the change in the readings shown on the burette. A three way cock is used both to fill the burette and to allow the fuel to flow to the engine Air flow measurement: Air flow is measured using an air box Orifice is fixed in the inlet of air box suction pressure difference across the orifice is read on the U-tube manometer mounted on the panel. The outlet of the air suction box goes to the engine through the flexible hose for air suction. measurement: For heat balance analysis the PT-100 sensors are connected at exhaust gas calorimeter and engine cooling. V. EQUIPMENTS USED FOR THE EXPERIMENT Table:1Engine Specification Sr. no. Items Specifications 1 Model KIRLOSKAR, AV1 2 Compression ratio 19:1 3 Method of Hand starting starting 4 Type, no. of cylinders Vertical 4stroke,1cylinder 5 Bore x 87.5x110 stroke(mm 6 Cubic capacity Maximum 5 Hp power 8 Nominal speed 1500 rpm 9 Cooling system Water-cooled 10 Fuel filter Present 11 Lube oil filter Present 79 P a g e

3 ISSN : , Vol. 4, Issue 3( Version 1, March 2014, pp Table: 2Properties of Diesel, Palm oil, Mustard oil and its blends Fuel Density( Kg/m 3 VI. EXPERIMENTAL PROCEDURE Fill the fuel tank with the fuel. Start the cooling water supply to the engine and the calorimeter. Fill the burette with the fuel. Switch on the control panel. Start the engine with cranking handle provided. Note down the readings in the observation table. Load the engine gradually by providing weights on the loading hanger. Note down the reading, for various load. VII. CALCULATIONS The basic performance parameters that were determined for performance evaluation of engine are: Brake Power Brake thermal efficiency Brake specific fuel consumption Total fuel consumption Various formulae that were used for performance evaluation are listed below: The brake power is calculated by measuring load on dynamometer and engine speed and then putting these values in, = Calorific value(kj /Kg Flash Point( 0 C ( W s π D + d N KW Fire Point( 0 C Diesel Mustard oil Palm oil BB BB BB BB BB Where, W is the weight applied on spring balance N is the engine speed in RPM D = Dia. of Drum (340mm d = Dia. of Rope (20mm The fuel consumption rate is noted for each loading and then brake specific fuel consumption is calculated as, = 3600 kg/kw-hr The brake thermal efficiency of the engine is calculated as, = CV 100 Total fuel consumption, = cc(ml time (specificgravity 1000 VIII. kg sec RESULTS Variation of Total Fuel Consumption with for different fuels Figure 2: Variation of Total Fuel Consumption with for different fuels FIGURE:2, Depicts about variation in total fuel consumption with bp for different fuels. From the curve it is observed that the value of the total fuel consumption is increased from BB10 to BB40, after that the blending ratio are increases, decreases in the total fuel consumption. We get better total fuel consumption at BB10 and BB Figure 3: Variation of Brake specific fuel consumption with for different fuels 0 BB 10 BB 20 BB 30 BB 40 BB 50 BB Variation of Brake specific fuel consumption with for different fuels 0 BB 10 BB 20 BB 30 BB 40 BB 50 BB FIGURE:3, Depicts about variation in Brake specific fuel consumption with bp for different fuels. From the curve it is observed that the value of the total fuel consumption is increased from BB10 to BB40, after that the blending ratio are increases, decreases in the 80 P a g e

4 ISSN : , Vol. 4, Issue 3( Version 1, March 2014, pp Brake specific fuel consumption. We get better Brake specific fuel consumption at BB10 and BB Figure 4: Variation of Brake Thermal Efficiency with for different fuels FIGURE:4, Depicts about variation in Brake thermal efficiency with bp for different fuels. From the curve it is observed that the value of the Brake thermal efficiency is decreased from BB10 to BB40, after that the blending ratio are increases, increases in the Brake thermal efficiency. We get better Brake thermal efficiency at BB10 and BB Variation of BrakeThermal Efficiency with for different fuels 0 BB 10 BB 20 BB 30 BB 40 BB 50 BB Variation of exhaust gas tempe with Brake Power for different fuels Figure 5: Variation of exhaust gas tempe with Brake Power for different fuels FIGURE:5, Depicts about variation in Exhaust gas tempe with bp for different fuels. From the curve it is observed that the value of the Exhaust gas tempe is increased from BB10 to BB40, after that the blending ratio are increases, decreases in the Exhaust gas tempe. We get better Exhaust gas tempe at BB10 and BB20. Table:3 PERFORMANCE ANALYSIS Vegetable oil Blend Calorific Value (MJ/kg Pure Diesel BB BB BB BB BB BB 10 BB 20 BB 30 BB 40 BB 50 BB BB 10 BB20 BB30 BB40 BB50 BB calorific value Figure 6: Graphical representation of Calorific value of different fuel Table:4 RUNNING COST OF ENGINE WITH DIFFERENT BLENDS Fuel Cost (Rs./lr. Diesel Mustard oil Palm oil BB BB BB BB BB IX. CONCLUSION The value of the total fuel consumption is increased from BB10 to BB40, after that the blending ratio are increases, decreases in the total fuel consumption. We get better total fuel consumption at BB10 and BB20. The value of the total fuel consumption is increased from BB10 to BB40, after that the blending ratio are increases, decreases in the Brake specific fuel consumption. We get better Brake specific fuel consumption at BB10 and BB20. The value of the Brake thermal efficiency is decreased from BB10 to BB40, after that the blending ratio are increases, increases in the Brake thermal efficiency. We get better Brake thermal efficiency at BB10 and BB20. The value of the Exhaust gas tempe is increased from BB10 to BB40, after that the blending ratio are increases, decreases in the Exhaust gas tempe. We get better Exhaust gas tempe at BB10 and BB20. REFRENCES [1] A. K. Azad et. al. Mustard oil, an alternative Fuel: An experimental investigation of Bio-diesel properties with and without Trans-esterification reaction Global Advanced Research Journal of 81 P a g e

5 ISSN : , Vol. 4, Issue 3( Version 1, March 2014, pp Engineering, Technology and Innovation Vol. 1(3 pp , June, [2] T. Venkata Subba Rao et. Al. Performance Analysis of Vegetable Oil Blended With Diesel Additive International Journal of Engineering Research and Applications (IJERA ISSN: Vol. 2, Issue 5, September- October 2012, pp [3] A. Haiter Lenin et. al. Experimental Investigations on a Diesel Engine using Blends of Methyl Esters of Pongamia Oil as the Fuels European Journal of Scientific Research ISSN X Vol.72 No.2 (2012, pp EuroJournals Publishing, Inc [4] K. Arun Balasubramanian Dual Biodiesel Blends in Diesel Engine - Performance and Emission Analysis European Journal of Scientific Research ISSN X Vol.75 No.3 (2012, pp EuroJournals Publishing, Inc [5] K. Karuppasamy et. al. The Effect of Biodiesel Blends on Single Cylinder DI Diesel Engine and Optimization using Response Surface Methodology European Journal of Scientific Research ISSN X Vol.84 No.3 (2012, pp EuroJournals Publishing, Inc [6] Lovekush Prasad et. al. Experimental Investigation of Performance of Diesel Engine Working On Diesel and Neem Oil Blends IOSR Journal of Mechanical and Civil Engineering (IOSRJMCE ISSN: Volume 1, Issue 4 (July-August 2012, PP [7] Jawad Nagi et. al. Palm Biodiesel an Alternative Green Renewable Energy for the Energy Demands of the Future International Conference on Construction and Building Technology, ICCBT F - (07 pp [8] K. Anbumani et. al. Performance of Mustard And Neem Oil Blends With Diesel Fuel In C.I. Engine ARPN Journal of Engineering and Applied Sciences Vol. 5, No. 4, APRIL 2010, ISSN Asian Research Publishing Network (ARPN. [9] Khiraiya Krunal B. et. al. A Review of Recent Research on Palm oil Biodiesel as Fuel for CI Engine International Journal of Applied Research & Studies ISSN , ijars/ Vol. II/ Issue I/Jan, 2013/293. [10] Mazel, M.A., summers, J.D. and Batch elder, D.G.1985 Peanut, soybean and cottonseed oil as diesel fuels Trans. ASAE. 28(5: [11] Canakei, M. and Van Gerpen, J Comparison of engine performance and emissions for petroleum diesel fuel, yellow grease biodiesel and soybean oil biodiesel American Society of Agricultural Engineers. 46(4: [12] F. Karaosmanoglu, G. Kurt and T. Ozaktas, Long term C.I engine test of sunflower oil, International journal of Renewable Energy, Vol. 19, 2000, [13] O. M. I. Nwafor and G. Rice, Performance of rapeseed oil methyl ester in diesel engine, International journal of Renewable Energy, Vol. 95, [14] P. K. Devan and N. V. Mahalakshmi, Performance, emission and combustion characteristics of poon oil and its diesel blends in a DI diesel engine, Fuel, Vol. 88, 2009, [15] Altan R, Cetinkay S, Yucesu HS (2001. The potential of using vegetable oil fuels as fuel for diesel engines, Energy Conversion and Management, 42(5: Sr. No. OBSERVATION TABLE W(KG S(KG N (RPM APENDIX Table 5: Pure Diesel FUEL TIME T1 (ML (SEC T P a g e

6 ISSN : , Vol. 4, Issue 3( Version 1, March 2014, pp W(KG S(KG Table 6: 90%Diesel, 5% Palm oil, 5% Mustard oil (RPM (ML (SEC W(KG S(KG Table 7: 80% Diesel, 10% Palm oil, 10% Mustard oil (RPM (ML (SEC W(KG S(KG Table 8: 70% Diesel, 15% Palm oil, 15% Mustard oil (RPM (ML (SEC W(KG S(KG Table 9: 60% Diesel, 20% Palm oil, 20% Mustard oil (RPM (ML (SEC P a g e

7 ISSN : , Vol. 4, Issue 3( Version 1, March 2014, pp W(KG S(KG Table 10: 50% Diesel, 25% Palm oil, 25% Mustard oil (RPM (ML (SEC Table 711: Total Fuel Consumption & of Different blending ratio with Diesel 0 BB 10 BB 20 BB 30 BB 40 BB 50 BB (kw (kw (kw (kw (kw (kw Table 8: & Break Powers of different blending ratio with Diesel 0 BB 10 BB 20 BB 30 BB 40 BB 50 BB W-hr (kw W-hr (kw W-hr (kw W-hr (kw W-hr (kw W-hr (kw P a g e

8 ISSN : , Vol. 4, Issue 3( Version 1, March 2014, pp ( C Table 9: & Break Powers of different blending ratio with Diesel 0 BB 10 BB 20 BB 30 BB 40 BB 50 BB (k W (k W (k W (k W (k W Table 10: Exhaust Gas s & Break Powers of different blending ratio with Diesel 0 BB 10 BB 20 BB 30 BB 40 BB 50 BB (kw (kw (kw (kw (kw ( C ( C ( C ( C ( C (k W (kw P a g e