Aluminum Conduit Bodies, Covers and Gaskets For Rigid Conduit & IMC.
|
|
|
- Pearl Mitchell
- 5 years ago
- Views:
Transcription
1 NEC/CEC Suitable for use in the following Applications To provide access to conductors for pulling, splicing, maintenance and future changes/upgrades. Allows connection of straight conduit runs, branch conduit runs and 90 bends. Features Tapered threaded hubs (NPT). Raintight when used with gasketed covers. Internal volume and maximum wire clearly marked on castings. Standard Materials Bodies: copperfree (max. 4/10 of 1%) aluminum 1/2 thru 2 : pressure cast 2-1/2 thru 4 : sand cast Blank covers: malleable iron, steel or copperfree (max. 4/10 of 1%) aluminum Cover screws: stainless steel Gaskets: neoprene or composition fiber Standard Finishes Aluminum bodies: epoxy powder coat Stamped aluminum covers: natural finish Cast aluminum covers: epoxy powder coat NEC/CEC Certifications and Compliances UL Standards: 514A UL Listed: E-18095w CSA Standard: C22.2 No. 18 CSA Certified: NEMA Standard: FB-1, FB-2.10 Type LB-A Type T-A Type LL-A Type LR-A Type C-A 50
2 NEC/CEC Suitable for use in the following Aluminum Conduit Bodies (Inches) Max. Wire Fill LB-A Max. Wire Fill T-A Diecast 1/2 LB-50A T-50A 3/4 (3) # 6 LB-75A (3) # 6 T-75A 1 (3) # 4 LB-100A (3) # 4 T-100A 1-1/4 (3) # 2 LB-125A (3) # 2 T-125A 1-1/2 (3) # 1/0 LB-150A (3) # 1 T-150A 2 (3) # 4/0 LB-200A (3) # 2/0 T-200A Sandcast 2-1/2 (3) 300 LB-250A (3) 300 T-250A 3 (3) 400 LB-300A (3) 300 T-300A 3-1/2 (3) 500 LB-350A (3) 350 T-350A 4 (3) 500 LB-400A (3) 350 T-400A (Inches) Max. Wire Fill LL-A Max. Wire Fill LR-A Diecast 1/2 LL-50A LR-50A 3/4 (3) # 6 LL-75A (3) # 6 LR-75A 1 (3) # 4 LL-100A (3) # 4 LR-100A 1-1/4 (3) # 2 LL-125A (3) # 2 LR-125A 1-1/2 (3) # 1 LL-150A (3) # 1 LR-150A 2 (3) # 2/0 LL-200A (3) # 2/0 LR-200A Sandcast 2-1/2 (3) 300 LL-250A (3) 300 LR-250A 3 (3) 350 LL-300A (3) 350 LR-300A 3-1/2 (3) 350 LL-350A (3) 350 LR-350A 4 (3) 350 LL-400A (3) 350 LR-400A All 1/2 Max Wire Fill Calculations per the NEC - Annex C - Table C8. 51
3 NEC/CEC Suitable for use in the following Aluminum Conduit Bodies (Inches) Max. Wire Fill Diecast C-A Sandcast 1/2 C-50A 3/4 (3) # 6 C-75A 1 (3) # 4 C-100A 1-1/4 (3) # 2 C-125A 1-1/2 (3) # 1/0 C-150A 2 (3) # 3/0 C-200A 2-1/2 (3) 300 C-250A 3 (3) 300 C-300A 3-1/2 (3) 350 C-350A 4 (3) 350 C-400A Sandcast (Inches) Max. Wire Fill TB-A Max. Wire Fill X-A 1/2 TB-50A X-50A 3/4 (3) # 6 TB-75A (3) # 6 X-75A 1 (3) # 6 TB-100A (3) # 4 X-100A 1-1/4 (3) # 6 TB-125A X-125A 1-1/2 (3) # 4 TB-150A X-150A 2 (3) # 1/0 TB-200A X-200A 2-1/ /2 4 All 1/2 Max Wire Fill Calculations per the NEC - Annex C - Table C8. 52
4 NEC/CEC Suitable for use in the following Blank Covers and Gaskets Body Size (Inches) Domed Top Design Cover Velbuna Solid Cover Sealing Gasket Neoprene 1/2 BS-50A SG-50 SGN-50 3/4 BS-75A SG-75 SGN-75 1 BS-100A SG-100 SGN /4-1-1/2 BS-125A SG-125 SGN BS-200A SG-200 SGN /2-3 BS-250A SG-250 SGN /2-4 BS-350A SG-350 SGN-350 Flat Top Design Cover 53
5 NEC/CEC Suitable for use in the following Dimensions in Millimeters (Inches) (Inches) Pressure Cast /2 (3.94) /4 (4.63) (5.38) 1-1/4 1-1/ (9.50) Sand Cast /2 (12.25) (12.25) /2 (14.88) (14.88) Types C, T, TB, X Types LB, LL, LR Dimensions In Millimeters (Inches) A B C D E F G H J L M N P 33.3 (1.31) 39.6 (1.56) 46.0 (1.81) 79.5 (3.13) (5.50) (5.50) 35.1 (1.38) 41.4 (1.63) 47.8 (1.88) 87.4 (3.44) 98.6 (3.88) (4.63) (5.19) (5.56) (4.75) (5.63) 1 (6.69) (8.56) (8.56) (10.81) (15.13) (15.13) (18.13) (18.13) 65.0 (2.56) 76.2 (3.00) 50.8 (2.00) 66.8 (2.63) (4.19) (5.75) (5.75) (7.13) (7.13) 52.3 (2.06) 62.0 (2.44) 71.4 (2.81) 98.6 (3.88) 96.8 (3.81) (4.56) (5.25) (6.81) (4.13) (6.56) (6.44) (8.31) (11.88) (11.56) (14.00) (13.75) (5.13) (7.88) (7.88) (10.19) (13.69) (13.69) (16.50) (16.50) 16.0 (0.63) 19.1 (0.75) 23.9 (0.94) 26.9 (1.06) 30.2 (1.19) 38.1 (1.50) 46.0 (1.81) 55.6 (2.19) 28.7 (1.13) 35.1 (1.38) 42.9 (1.69) 54.1 (2.13) 60.5 (2.38) 74.7 (2.94) 85.9 (3.38) (4.13) (4.75) (5.13) 79.8 (3.14) 96.0 (3.78) (4.50) (8.06) (10.63) (10.63) (13.13) (13.13) 26.7 (1.05) 32.3 (1.27) 38.6 (1.52) 93.7 (3.69) 93.7 (3.69) 54
6 NEC/CEC Suitable for use in the following Applications To provide access to conductors for pulling, splicing, maintenance and future changes/ upgrades. Allows connection of straight conduit runs, branch conduit runs and 90 bends. Features Tapered threaded hubs (NPT). Packaged complete with cover and gasket under one Catalog Number. Ready to use. Standard Materials Conduit Body: copperfree (max. 4/10 of 1%) aluminum Cover: Type BS copperfree (max. 4/10 of 1%) aluminum Gasket: Type SGN Neoprene Standard Finishes Conduit Body - epoxy powder coat enamel NEC/CEC Certifications and Compliances UL Standards: 514A UL Listed: E CSA Standard: C22.2 No. 18 CSA Certified: LR-9795 NEMA Standard: FB-1, FB-2.10 Type LB-ACG Type T-ACG Type LL-ACG Type LR-ACG Type C-ACG 55
7 NEC/CEC Suitable for use in the following Aluminum Conduit Bodies (Inches) Max. Wire Fill LB-ACG Max. Wire Fill T-ACG Max. Wire Fill LL-ACG 1/2 LB-50ACG T-50ACG LL-50ACG 3/4 (3) # 6 LB-75ACG (3) # 6 T-75ACG (3) # 6 LL-75ACG 1 (3) # 4 LB-100ACG (3) # 4 T-100ACG (3) # 4 LL-100ACG 1-1/4 (3) # 2 LB-125ACG (3) # 2 T-125ACG (3) # 2 LL-125ACG 1-1/2 (3) # 1/0 LB-150ACG (3) # 1 T-150ACG (3) # 1 LL-150ACG 2 (3) # 4/0 LB-200ACG (3) # 2/0 T-200ACG (3) # 2/0 LL-200ACG (Inches) Max. Wire Fill LR-ACG Max. Wire Fill C-ACG 1/2 LR-50ACG C-50ACG 3/4 (3) # 6 LR-75ACG (3) # 6 C-75ACG 1 (3) # 4 LR-100ACG (3) # 4 C-100ACG 1-1/4 (3) # 2 LR-125ACG (3) # 2 C-125ACG 1-1/2 (3) # 1 LR-150ACG (3) # 1/0 C-150ACG 2 (3) # 2/0 LR-200ACG (3) # 3/0 C-200ACG All 1/2 Max Wire Fill Calculations per the NEC - Annex C - Table C8. 56
8 NEC/CEC Suitable for use in the following Dimensions in Millimeters (Inches) (Inches) Pressure Cast 1/2 3/ /4 1-1/2 2 Sand Cast 2-1/ /2 4 Types C, T, TB, X Types LB, LL, LR Dimensions In Millimeters (Inches) A B C D E F G H J L M N P (3.94) (4.63) (5.38) (9.50) (12.25) (12.25) (14.88) (14.88) 33.3 (1.31) 39.6 (1.56) 46.0 (1.81) 79.5 (3.13) (5.50) (5.50) 35.1 (1.38) 41.4 (1.63) 47.8 (1.88) 87.4 (3.44) 98.6 (3.88) (4.63) (5.19) (5.56) (4.75) (5.63) 1 (6.69) (8.56) (8.56) (10.81) (15.13) (15.13) (18.13) (18.13) 65.0 (2.56) 76.2 (3.00) 50.8 (2.00) 66.8 (2.63) (4.19) (5.75) (5.75) (7.13) (7.13) 52.3 (2.06) 62.0 (2.44) 71.4 (2.81) 98.6 (3.88) 96.8 (3.81) (4.56) (5.25) (6.81) (4.13) (6.56) (6.44) (8.31) (11.88) (11.56) (14.00) (13.75) (5.13) (7.88) (7.88) (10.19) (13.69) (13.69) (16.50) (16.50) 16.0 (0.63) 19.1 (0.75) 23.9 (0.94) 26.9 (1.06) 30.2 (1.19) 38.1 (1.50) 46.0 (1.81) 55.6 (2.19) 28.7 (1.13) 35.1 (1.38) 42.9 (1.69) 54.1 (2.13) 60.5 (2.38) 74.7 (2.94) 85.9 (3.38) (4.13) (4.75) (5.13) 79.8 (3.14) 96.0 (3.78) (4.50) (8.06) (10.63) (10.63) (13.13) (13.13) 26.7 (1.05) 32.3 (1.27) 38.6 (1.52) 93.7 (3.69) 93.7 (3.69) 57
9 Set Screw Type for EMT (Thinwall Conduit). NEC/CEC Suitable for use in the following Applications To provide access to conductors for pulling, splicing, maintenance and future changes/ upgrades. Allows connection of straight conduit runs, branch conduit runs and 90 bends. Features Slotted hex head steel hardened cup-point set screw for EMT. Internal volume and maximum wire clearly marked on castings. Standard Materials Diecast copperfree (max. 4/10 of 1%) aluminum Standard Finishes Aluminum enamel NEC/CEC Certifications and Compliances UL Standards: 514A UL Listed: E CSA Standard: C22.2 No. 18 CSA Certified: NEMA Standard: FB-1, FB-2.10 Type LB-TW Type T-TW Type LL-TW Type LR-TW Type C-TW 58
10 Set Screw Type for EMT (Thinwall Conduit). NEC/CEC Suitable for use in the following Aluminum Conduit Bodies (Inches) Max. Wire Fill LB-TW Max. Wire Fill T-TW Max. Wire Fill LL-TW 1/2 LB-50ATW T-50ATW LL-50ATW 3/4 (3) # 6 LB-75ATW (3) # 6 T-75ATW (3) # 6 LL-75ATW 1 (3) # 4 LB-100ATW (3) # 4 T-100ATW (3) # 4 LL-100ATW 1-1/4 (3) # 2 LB-125ATW (3) # 2 T-125ATW (3) # 2 LL-125ATW 1-1/2 (3) # 1/0 LB-150ATW (3) # 1 T-150ATW (3) # 1 LL-150ATW 2 (3) # 4/0 LB-200ATW (3) # 2/0 T-200ATW (3) # 2/0 LL-200ATW (Inches) Max. Wire Fill LR-TW Max. Wire Fill C-TW 1/2 LR-50ATW C-50ATW 3/4 (3) # 6 LR-75ATW (3) # 6 C-75ATW 1 (3) # 4 LR-100ATW (3) # 4 C-100ATW 1-1/4 (3) # 2 LR-125ATW (3) # 2 C-125ATW 1-1/2 (3) # 1 LR-150ATW (3) # 1/0 C-150ATW 2 (3) # 2/0 LR-200ATW (3) # 3/0 C-200ATW All 1/2 Max Wire Fill Calculations per the NEC - Annex C - Table C8. 59
11 NEC/CEC Suitable for use in the following Blank Covers and Gaskets Body Size (Inches) Domed Top Design Cover Velbuna Solid Cover Sealing Gasket Neoprene 1/2 BS-50A SG-50 SGN-50 3/4 BS-75A SG-75 SGN-75 1 BS-100A SG-100 SGN /4-1-1/2 BS-125A SG-125 SGN BS-200A SG-200 SGN /2-3 BS-250A SG-250 SGN /2-4 BS-350A SG-350 SGN-350 Flat Top Design Cover 60 v
12 NEC/CEC Suitable for use in the following Dimensions in Millimeters (Inches) (Inches) Pressure Cast /2 (3.94) /4 (4.63) (5.38) 1-1/4 1-1/ (9.50) Sand Cast /2 (12.25) (12.25) /2 (14.88) (14.88) Types C, T, TB, X Types LB, LL, LR Dimensions In Millimeters (Inches) A B C D E F G H J L M N P 33.3 (1.31) 39.6 (1.56) 46.0 (1.81) 79.5 (3.13) (5.50) (5.50) 35.1 (1.38) 41.4 (1.63) 47.8 (1.88) 87.4 (3.44) 98.6 (3.88) (4.63) (5.19) (5.56) (4.75) (5.63) 1 (6.69) (8.56) (8.56) (10.81) (15.13) (15.13) (18.13) (18.13) 65.0 (2.56) 76.2 (3.00) 50.8 (2.00) 66.8 (2.63) (4.19) (5.75) (5.75) (7.13) (7.13) 52.3 (2.06) 62.0 (2.44) 71.4 (2.81) 98.6 (3.88) 96.8 (3.81) (4.56) (5.25) (6.81) (4.13) (6.56) (6.44) (8.31) (11.88) (11.56) (14.00) (13.75) (5.13) (7.88) (7.88) (10.19) (13.69) (13.69) (16.50) (16.50) 16.0 (0.63) 19.1 (0.75) 23.9 (0.94) 26.9 (1.06) 30.2 (1.19) 38.1 (1.50) 46.0 (1.81) 55.6 (2.19) 28.7 (1.13) 35.1 (1.38) 42.9 (1.69) 54.1 (2.13) 60.5 (2.38) 74.7 (2.94) 85.9 (3.38) (4.13) (4.75) (5.13) 79.8 (3.14) 96.0 (3.78) (4.50) (8.06) (10.63) (10.63) (13.13) (13.13) 26.7 (1.05) 32.3 (1.27) 38.6 (1.52) 93.7 (3.69) 93.7 (3.69) 61
Spec 5 Conduit Bodies, Covers and Gaskets For Rigid Conduit and IMC
NEC/CEC Suitable for use in the following Applications To provide access to conductors for pulling, splicing, maintenance and future changes/ upgrades. Allows connection of straight conduit runs, branch
Form 85 Unilets Conduit Outlet Bodies, Covers and Gaskets For use with Rigid Steel, Rigid Aluminum, IMC, and EMT Conduit.
For use with Rigid Steel, Rigid Aluminum, IMC, and EMT Conduit. NEC/CEC Suitable for use in the following Applications Serve as pulling fittings. Make bends in conduit system. Provide openings for splicing.
Form 35 Malleable Iron Conduit Outlet Bodies, Covers and Gaskets For use with Rigid Steel, Rigid Aluminum and IMC Conduit.
NEC/CEC Suitable for use in the following Applications Serve as pulling fittings. Make bends in conduit system. Provide openings for splicing. Connect and change direction of conduit runs. Allow connections
FM9 Aluminum Conduit Outlet Bodies, Covers and Gaskets For use with Rigid Steel, Rigid Aluminum and IMC.
Applications Serve as pulling fittings. Make bends in conduit system. Provide openings for splicing. Connect and change direction of conduit runs. Allow connections for branch runs. Permit access to conductors
LB125A 1-1/4" LB Form 5 Aluminum Conduit Body. Dimensions and Weight STUD SIZE #10; 0.97 INCH LENGTH; INSULATION SUPPORT
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 LB125A 1-1/4" LB Form 5 Aluminum Conduit Body Appleton/Oz Gedney Catalog Number Manufacturer Description Weight per unit
FM8 Conduit Outlet Bodies, Covers and Gaskets For use with Rigid Steel, Rigid Aluminum and IMC Conduit.
NEC/CEC Suitable for use in the following Applications Serve as pulling fittings. Make bends in conduit system. Provide openings for splicing. Connect and change direction of conduit runs. Allow connections
FM7 Conduit Outlet Bodies, Covers and Gaskets For use with Rigid Steel, Rigid Aluminum and IMC Conduit.
NEC/CEC Suitable for use in the following Applications Serve as pulling fittings. Make bends in conduit system. Provide openings for splicing. Connect and change direction of conduit runs. Allow connections
FM9 Aluminum Unilet Conduit Outlet Bodies, Covers and Gaskets For use with Rigid Steel, Rigid Aluminum and IMC.
FM9 Aluminum Unilet Conduit Outlet Bodies, Covers and Gaskets For use with Rigid Steel, Rigid Aluminum and IMC. : Conduit Bodies Applications Serve as pulling fittings. Make bends in conduit system. Provide
COMMERCIAL AND INDUSTRIAL FITTINGS: CONDUIT BODIES. Applications
Class I, Division per NEC 50.0(B)() Applications Larger body size facilitates pulling of large and heavy conductors. Specially designed raised cast covers provide additional wiring area. Mogul Unilets
T38 1" T Form 7 Malleable Iron Conduit Body. Material, Color, and Finish Color Gray 0 Zinc Electroplate/Chromate/Epoxy Powder Coat
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 T38 1" T Form 7 Malleable Iron Conduit Body Appleton/Oz Gedney Catalog Number Manufacturer Description Weight per unit
Form 7 Iron Conduit Bodies, Covers and Gaskets For use with Rigid Steel, Rigid Aluminum and IMC Conduit.
NEC/CEC Suitable for use in the following Applications Serve as pulling fittings. Make bends in conduit system. Provide openings for splicing. Connect and change direction of conduit runs. Allow connections
Material, Color, and Finish Color Gray 0 Zinc Electroplate/Chromate/Epoxy Powder Coat
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 T37 1 T FM7 CND BD Appleton/Oz Gedney Catalog Number T37 Manufacturer Appleton/Oz Gedney Description FM7 Unilets Type
1-1/2 AL LB FM7 CND BD. Features. Material, Color, and Finish. Dimensions and Weight. Descriptions. Manufacturer Information
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 LB57SA 1-1/2 Al LB FM7 CND BD Appleton/Oz Gedney Catalog Number Manufacturer Description Weight per unit Product Category
BUB400M 4-In Mog Cond Body. Features. Material, Color, and Finish. Dimensions and Weight
380 South Street 7596-763, TX Nacogdoches Phone: 936-569-79 Fax: 936-560-685 BUB00M -In Mog Cond Body Appleton/Oz Gedney Catalog Number Manufacturer Description Weight per unit Product Category Features
Aluminum and Steel Liquidtight Strain Relief Cord and Cable Connectors
Application Provide a liquidtight and strain relief termination for flexible type neoprene, hypalon, and PVC jacketed power or control cord and cable. For use in wet or dry locations sealing electrical
CONDUIT BODIES CONDUIT BODIES. Phone:
i i Con it Bo ies allea le I on o i i I C con it cond ctors or p llin splicin Tapered threaded hu s - NPT Suita le or use in concrete Threaded LB Conduit Bodies MLB1 1/2 4-11/16 1-5/16 2-1/16 70 70.6 MLB2
Rigid/Aluminum Conduit Bodies, Gaskets and Covers
Rigid/luminum Conduit odies, Gaskets and Covers Conduit odies, Covers and Gaskets Weatherproof oxes and Covers pplications Junction for branch conduits Series bodies for Rigid and IMC conduit maintain
Conduit Outlet Boxes and Bodies: Malleable Iron or Aluminum; Explosionproof, Dust-Ignitionproof UNILETS for use with Threaded Metal Conduit.
-2 Conduit Outlet Boxes and Bodies: Malleable Iron or Aluminum; UNILETS for use with Threaded Metal Conduit. Applications Meet a wide range of classified area requirements. Corrosion-resistant ideal indoors
Receptacle housing and cover optional malleable iron on EFS-M Series. Spring-loaded cover seats against neoprene gasket.
U-Line Factory Sealed 20 Amp Plugs and Receptacles Dead-Front Safety Construction. Choice of Aluminum or Thermoplastic Polyester Plug. Class I, Division 1 and 2 Groups B, C, D NEMA 3, 3R, 7BCD, 9FG Applications
U-Line Contender Factory Sealed 20 Amp Plugs and Receptacles Explosionproof, Dust-Ignitionproof
U-Line Contender Factory Sealed 20 Amp Plugs and Receptacles Explosionproof, Dust-Ignitionproof Class I, Groups C, D Class I, Division 2, Group B Class I, Zone 1, Group IIB Class I, Zone 2, Group IIB +
Receptacle housing and cover optional malleable iron on EFS-M Series. Spring-loaded cover seats against neoprene gasket.
U-Line Factory Sealed 20 Amp Plugs and Receptacles Dead-Front Safety Construction. Choice of Aluminum or Thermoplastic Polyester Plug. Class I, Division 1 and 2 Groups B, C, D NEMA 3, 3R, 7BCD, 9FG Applications
CONTROLS: NEC/CEC EXPLOSIONPROOF CONTROL STATIONS AND SWITCHES. Applications. Illustrated Features
Explosionproof, Dust-Ignitionproof Malleable Iron Body and Cover. Furnished with Internal Ground. Applications Designed to prevent arcing of enclosed switches in ignitable atmospheres during connect and
Product Description. Junction Boxes...V1-V23 Meter and Instrument Enclosures...V24-V33
SECTION V INDEX Product Description Page Number Junction Boxes......................................V-V2 Meter and Instrument Enclosures.......................V24-V Control Centers.....................................V4-V9
Condulet Single Gang Cast Device Boxes With and Without Mounting Lugs for Threaded Rigid and IMC Conduit
Condulet Single Gang Cast Accessories Pages to 44 F Application: Cast device boxes are installed to: accommodate wiring devices act as pull boxes for conductors in a conduit system provide openings to
EFS Non-Sealed Tumbler Switches Explosionproof, Dust-Ignitionproof Malleable Iron Body and Cover. Furnished with Internal Ground Screw.
Explosionproof, Dust-Ignitionproof Malleable Iron Body and Cover. Furnished with Internal Ground Screw. Applications Designed to prevent arcing of enclosed switches in ignitable atmospheres during connect
Corrosion Protection for Electrical Conduit and Fittings
Easy access for pulling, splicing, mounting and maintenance! 3 4" LB Form 8 conduit body and cover 2 1 2" LB Form 8 conduit body and cover OCAL-BLUE Double-Coat Conduit Bodies With OCAL-BLUE Double-Coat
EDS Factory Sealed Tumbler Switches Explosionproof, Dust-Ignitionproof UNILETS for Use with Threaded Metal Conduit.
UNILETS for Use with Threaded Metal Conduit. Class I, Division 1 and 2, Groups B, C, D Applications Designed to prevent arcing of enclosed switches in ignitable atmospheres during connect and disconnect
CEC: Class I, Division 1 and 2, Groups B, C, D Class II, Division 1 and 2, Groups E, F, G Class III Type 4X Exd IIB + H 2
Integrally Ballasted. 50 W, 70 W, 00 W, 50 W HPS; 75 W PSMH. 75 W MH. Medium Base. For Use with Threaded Metal Conduit. Applications For use in chemical and petrochemical plants, such as manufacturers
D2P and EWP Factory Sealed Circuit Breaker Panelboards Explosionproof, Dust-Ignitionproof, Watertight, Corrosion-Resistant
Applications Protection and control of electrical equipment and circuits such as lighting and heat tracing in hazardous locations or in damp, wet or corrosive conditions. D2P Series designed for use in
Areamaster 1000 Floodlights Integrally Ballasted W HID For hazardous locations.
A, IIB, IIC Applications Powerful, efficient weatherproof lighting for large areas such as: Pulp and paper mills Processing plants Chemical plants Oil refineries Foundries Storage areas Waste and sewage
Condulet Cast Device Boxes and Covers Application and Selection
F Condulet Cast and Covers Application and Selection Application: Cast device boxes are installed in conduit and cable systems to: Accommodate wiring devices Act as pull boxes for conductors in a conduit
Powertite Series Pin and Sleeve Plugs, Connectors and Receptacles
Powertite Series Pin and Sleeve Plugs, Connectors and Receptacles Applications Designed to supply power to portable or fixed electrical equipment such as motor generator units, welders, pumps, compressors,
Conduit Bushings for Rigid Metal Conduit and IMC
Applications Used with a locknut to terminate rigid metal conduit or IMC conduit to a box or enclosure. Features Provides a smooth pulling surface. Material/Finish BU: malleable iron/zinc electroplated
Spring-loaded cover seats against neoprene gasket.
U-Line Factory Sealed 20 Amp Plugs and Receptacles Dead-Front Safety Construction. Choice of Aluminum or Thermoplastic Polyester Plug. Class I, Division 1 and 2 Groups B, C, D NEMA 3, 3R, 7BCD, 9FG Plugs
Powertite Series Pin and Sleeve Plugs, Connectors and Receptacles
Applications Designed to supply power to portable or fixed electrical equipment such as motor generator units, welders, pumps, compressors, cellular relay stations, and similar apparatus. Ideal for use
XP Series Pre-Wired Factory Sealed Circuit Breaker Panelboards Explosionproof, Dust-Ignitionproof System
NEC/ Applications Protection and control of electrical apparatus and circuits in hazardous environments, either indoor or outdoor. Designed for Class I, Division 2 areas where flammable gases or vapors
Code Master Incandescent Factory Sealed Luminaires Explosionproof, Dust-Ignitionproof For use with threaded metal conduit.
Applications For use in hazardous locations such as plants where plastics, paints, thinners and petrochemicals are manufactured. For use in chemical and petrochemical plants, such as manufacturers of plastics,
Applications. Illustrated Features
Applications For use in locations where a high degree of corrosion resistance is required. FR Series: For use in areas where high humidity or water vapor are present Typical uses include meat- or food-processing
Applications. Separate sealing chamber and switch construction. Used on 20 Amp 4-way and all 30 Amp models.
Contender Series Factory Sealed Front Operated Tumbler Switches Malleable Iron Body and Cover. Furnished with Internal Ground. NEMA 3, 7CD, 9EFG Applications Designed to prevent arcing of enclosed switches
Mipco Connections for Refrigerated Containers. No One Does It Like Mipco. The Mipco. Advantage. Reliability. Safety. Easy Installation & Service
No One Does It Like Mipco Mipco Interlocked Reefer Power Outlets are used extensively in port terminals and shipboard applications to provide a safe, watertight electrical connection for refrigerated containers.
Industrial Areamaster LED Flood/High Bay Luminaires For Ordinary Locations. 250 W, 400 W, 750 W HID Light Level Equivalent
NEC/CEC: Type 3R, 4X IP66, IP67 Suitable for use in Wet Locations Marine Outside Type (Salt Water) Applications Powerful, efficient weatherproof lighting for applications such as: Security lighting Production
HID/FLOODLIGHT: NEC/CEC EXPLOSIONPROOF. Applications. Options
Applications UL Listed for Outside Type (Salt Water). Ideal in Class I, Division 1 and 2 installations in refineries, in pipeline transportation facilities, at drilling rigs and in production facilities
Standard Finishes Receptacles: epoxy powder coat Cord connector housings and caps: epoxy powder coat
U-Line Factory Sealed 15 and 20 Amp Plugs and Receptacles V Applications Locations where receptacles are used with stationary or portable electrically operated devices such as: Lighting systems Conveyors
Division 2 Contender Series Factory Sealed Control Stations
NEMA 3, 3R, 4, 4X, 12 IP66 Applications For use in washdown areas and other damp, wet and highly corrosive areas. Push buttons and selector switches are used in conjunction with contactors or magnetic
Applications. Standard Materials
Code Master Jr. HID Factory Sealed Luminaires Integrally Ballasted. 50 W, 70 W, 00 W, 50 W HPS; 50 W, 70 W, 00 W, 75 W PSMH. 75 W MH V. Medium Base. For Use with Threaded Metal Conduit. Class I, Division
Powertite Series Pin and Sleeve Plugs, Connectors and Receptacles
Applications Designed to supply power to portable or fixed electrical equipment such as motor generator units, welders, pumps, compressors, cellular relay stations, and similar apparatus. Ideal for use
AE Series Pin and Sleeve Plugs, Connectors and Receptacles Weatherproof 600 Vac, 250 Vdc. Pressure Wire Terminals.
AE Series Pin and Sleeve Plugs, Connectors and Receptacles 600 Vac, 250 Vdc. Pressure Wire Terminals. Applications Designed to supply power to portable or fixed electrical equipment such as: Welders Generators
NEC DBR Receptacle: Class II, Division 1 and 2, Groups F, G Class III NEMA 3, 3R, 4, 4X, 9FG
EBR/DBR 30, 60, 100 and 150 Amp Series Receptacles With Disconnect Switch or Circuit Breaker. Weatherproof Spring Cover. Explosionproof, Dust-Ignitionproof 600 Vac Max. 250 Vdc Max. NEC EBR Receptacle:
Cable Connectors & Conduit Sealing Bushings
RA1 Cable Terminators General Information Purpose: Cable Terminators and Sealing Fittings are used on conduit ends and cable ends to effectively seal the cable and conduit. Where Installed: Wherever the
NEC/CEC CLASS/ZONE RATED HAZARDOUS LOCATION CIRCUIT BREAKERS. Application
- and 3-Pole, Non-Interchangeable Trip. Bolted Enclosure Type. Class I, Division 1 and, Groups B, C, D Class II, Division 1 and, Groups E, F, G Distribution Equipment NEC/CEC CLASS/ZONE RATED HAZARDOUS
General Cable Support Information
General Cable Support Information Applications Used to support cables in vertical raceways or risers. Relieves the strain that would be placed on terminations, the interior of panels, or other devices
Taxonomies, Classifications, and Categories MYER'S HUB, 3-PIECE COUPLINGS, THREADLESS COUPLINGS AND THREADLESS CONNECTORS
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 NTCC125 1-1/4" Rigid Threadless Raintight Coupling ppleton/oz Gedney Manufacturer Description Weight per unit Product
Mercmaster LED Series Luminaires Enclosed and Gasketed Fixtures
Mercmaster Series Luminaires LIGHTING: ENCLOSED AND GASKETED AREA /INDUCTION Applications Enclosed and gasketed fixtures suitable for use in: Marine and wet locations A wide range of industrial, chemical
Contender Series Factory Sealed Control Stations and Pilot Lights Explosionproof, Dust-Ignitionproof Furnished with Internal Ground Screw.
Contender Series Factory Sealed Control Stations and Pilot Lights Furnished with Internal Ground Screw. Applications Push buttons and selector switches are used in conjunction with contactors or magnetic
Twist Lock - Explosion Proof - Dust Ignition Proof Receptacle Assembly
Twist Lock - Explosion Proof - Dust Ignition Proof Receptacle Assembly Part #: EPO-25A The Larson Electronics EPO-25A explosion proof power outlet provides a durable and secure weatherproof power connection
Areamaster LED Flood/High Bay Luminaires
Applications Typical applications include: Pulp and paper mills Processing plants Chemical plants Oil refineries Foundries Storage areas Waste and sewage treatment Parking garages Other areas where dust,
Lighting: Explosionproof Area HID. Applications. Standard Materials
Code Master Jr. HID Factory Sealed Luminaires Integrally Ballasted. 50 W, 70 W, 00 W, 50 W HPS; 50 W, 70 W, 00 W, 75 W PSMH. 75 W MH V. Medium Base. For Use with Threaded Metal Conduit. Class I, Division
EDS Factory Sealed Tumbler Switches Explosionproof, Dust-Ignitionproof UNILETS for Use with Threaded Metal Conduit.
EDS Factory Sealed Tumbler Switches UNILETS for Use with Threaded Metal Conduit. Class I, Division 1 and 2, Groups B, C, D NEMA 7 B CD, 9EFG Applications Designed to prevent arcing of enclosed switches
ELECTRICAL INSTALLATION
ENCLOSURE DIMENSIONS NOTES (3) 3/4" NPT WALL MOUNT BRACKET, (2) 5/16" DIA. THRU - HARDWARE IS CUSTOMER SUPPLIED 1¼" NPT AUTO-TEST OPTION 6.312" 160.3 mm 4.85" 123 mm 3.90" 99 mm 4.95" 126 mm 4.85" 123
Junction Boxes Hazardous and Non-Hazardous
Junction Boxes Hazardous and Non-Hazardous Description Page No. Application/Selection 112 Boxes Flush EGJ Series 19 WJBF Recessed Sidewalk Cover Series 116 Service Station EGJ Series 19 GUA Series 17 GUP
Powertite Series Pin and Sleeve Plugs, Connectors and Receptacles
Applications Designed to supply power to portable or fixed electrical equipment such as motor generator units, welders, pumps, compressors, cellular relay stations, and similar apparatus. Ideal for use
HID/AREA: NEC/CEC EXPLOSIONPROOF. Applications. NEC/CEC Certifications and Compliances
Integrally Ballasted. 50 W, 70 W, 100 W, 150 W, 250 W, 400 W HPS; 175 W, 250 W, 320 W, 350 W, 400 W PSMH; 175 W, 250 W, 400 W MH. Applications Ideal for use in chemical and petrochemical plants, such as
Specification Grade Insulated Bushings...DA1 Specification Grade Insulated Grounding Bushings...DA2-DA4. Insulating Bushings & Couplings...
SECTION D INDEX Product Description Page Number Specification Grade Insulated Bushings.....................DA Specification Grade Insulated Grounding Bushings........DA2-DA4 Insulating Bushings & Couplings.......................DA-DA6
EFS Non-Sealed Tumbler Switches Explosionproof, Dust-Ignitionproof Malleable Iron Body and Cover. Furnished with Internal Ground Screw.
EFS Non-Sealed Tumbler Switches Explosionproof, Dust-Ignitionproof Malleable Iron Body and Cover. Furnished with Internal Ground Screw. Controls CONTROLS: HAZARDOUS LOCATION CONTROL STATIONS AND SWITCHES
N2LED Series Emergency Luminaires Non-Metallic Emergency Egress Lighting Systems with Remote or Direct Mounted Lamps.
Applications Enclosed and gasketed, non-metallic emergency lighting system suitable for use in areas where flammable gases or vapors may become present due to abnormal, unusual or accidental conditions
PLUGS AND RECEPTACLES: NEC/CEC HAZARDOUS LOCATION
Explosionproof, Dust-Ignitionproof With Disconnect Switch or Circuit Breaker. Weatherproof Spring Cover. 600 Vac Max. 250 Vdc Max. Applications Locations where receptacles are used with stationary or portable
EPOXY POWDER COATED COPPER FREE ALUMINUM
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 AJA510 Alum MTG Unilet Appleton/Oz Gedney Catalog Number Manufacturer Description Weight per unit Product Category Features
Areamaster 100 Wide-Beam Floodlights 70 W, 100 W, 150 W HPS; 70 W, 100 W, 150 PSMH For general, marine and hazardous locations.
Areamaster 100 Wide-Beam Floodlights NEC CEC V Class II, Divisions I and 2, Groups E, F, G V Class III Applications Highly efficient, all-weather flood-lighting for lower wattage service. Well suited for:
1E EJB Junction Boxes Cl. I, Div. 1 and 2, Groups B, C, D
Cl. I, Div. and 2, Groups B, C, D Cl. II, Div., Groups E, F, G Cl. II, Div. 2, Groups F, G Cl. III NEMA 3, 4, 4*,, Ex d IIB + H2 T, IP Explosionproof Dust-Ignitionproof Raintight Wet Locations Applications:
Rigid Metal Conduit, IMC or EMT K-Clamps
65178 Rigid Metal Conduit, IMC or EMT K-Clamps Wt. Lbs. Std. Catalog No. Size (In.) Per 100 Pkg. Right Angle Type Right Angle Type Hot Dip/Mechanically Galvanized* For Rigid, IMC, EMT PC-50RA 1/2 37.0
Ground Connectors All Copper Alloy Specification Grade
Connectors For cable connection parallel or at right angles to pipe or rod. Features A high strength corrosion-resistant copper alloy ground connector connecting a ground wire either parallel or at right
PLUGS AND RECEPTACLES: NEC/CEC HAZARDOUS LOCATION
DBR 30, 60, 100 and 150 Amp Series Receptacles Explosionproof, Dust-Ignitionproof With Disconnect Switch or Circuit Breaker. Weatherproof Spring Cover. 600 Vac Max. 250 Vdc Max. Applications Locations
Powertite Series Pin and Sleeve Plugs, Connectors and Receptacles
Applications Designed to supply power to portable or fixed electrical equipment such as motor generator units, welders, pumps, compressors, cellular relay stations, and similar apparatus. Ideal for use
Condulet Conduit Bodies and Outlet Boxes Hazardous
Condulet Conduit Bodies and Outlet Boxes Hazardous 4F Description Page No. Application/Selection 48, 49 Lubricants HTL 59 STL 59 Conduit Bodies & Outlet Boxes Cylindrical EKC 57 90 Elbow LBH 58 LBY 58
LIGHTING: EXPLOSIONPROOF FLOODLIGHT. Applications. Options
Code Master 2 HID Factory Sealed Floodlights NEC: Class 1, Division 1 and 2, Groups C, D Marine Type Electric Fixtures Outside Type (Salt Water) CEC: V Class I, Division 1 and 2, Groups B, C, D Class II,
Plugs and Receptacles: Hazardous Location
U-Line Factory Sealed 15 and 20 Amp Plugs and Receptacles V Plugs and Receptacles Plugs and Receptacles: Hazardous Location Applications Locations where receptacles are used with stationary or portable
1E EJB Junction Boxes Cl. I, Div. 1 and 2, Groups B, C, D
EJB Junction Boxes Cl. I, Div. and 2, Groups B, C, D Cl. II, Div., Groups E, F, G Cl. II, Div. 2, Groups F, G Cl. III NEMA 3, 4, 4X*,, Ex d IIB + H2 T6, IP66 Explosionproof Dust-Ignitionproof Raintight
Areamaster LED Flood/High Bay Luminaires For Hazardous Locations. 250 W, 400 W, 750 W, 1000 W HID Light Level Equivalent
Class I, Division 2, Groups A, B, C, D Class I, Zone 2 Group IIC Class II, Division 1, Groups E, F, G Class II Division 2, Groups F, G Class III Simultaneous Exposure Type 3R, 4, 4X IP66/67 Applications
Enclosures. Section E
Enclosures Section E Enclosures and junction boxes built and configured to meet the requirements of the most demanding hazardous areas and industrial environmental applications across the globe. E Enclosures
CP Myers Hubs. Class I, Div. 2 Class II, Div. 1 and 2 Class III. when installed in accordance with the NEC. Features. Material.
Myers Hubs Class I, Div. 2 Class II, Div. 1 and 2 Class III when installed in accordance with the NEC. CP Myers Scru-tite TM and Ground hub are used in the termination of electrical circuits through wall
ENR Value Series Dead Front Interlocked Circuit Breaking Receptacles
ENR Value Series Dead Front Interlocked Circuit Breaking s Cl. I, Div. & 2, roups B, C, D Cl. II, Div. & 2, roups F, Cl. III, 7BCD, 9F, 2 Dust-Ignitionproof Raintight et Locations ENP Plugs Applications:
Weatherproof Boxes, Covers, Lampholders and Lighting Fixtures
Applications Use in branch circuit wiring for wet, damp or dry locations. May be used as a junction box or a device box for switches, receptacles, GFCIs, etc. Lampholders are for use in exterior and interior
Cable Connectors & Conduit Sealing Bushings
RA1 Cable Terminators General Information Purpose: Cable Terminators and Sealing Fittings are used on conduit ends and cable ends to effectively seal the cable and conduit. Where Installed: Wherever the
Mercmaster LED Series Luminaires Enclosed and Gasketed Fixtures
ATEX/IECEx: Zone 2 and 22 II 2 GD Lighting LIGHTING: ENCLOSED AND GASKETED AREA LED/INDUCTION Applications Enclosed and gasketed fixtures suitable for use in: Marine and wet locations A wide range of industrial,
W-Series Junction Boxes
W-Series Junction Boxes Application and Selection Junction boxes, designed for hazardous and non-hazardous locations, are used in a variety of industries to perform the following functions: As a pull box
Device Utility Finished FS Gang Conduit Bodies and Covers KO Seals Reducing Washers
Device Utility Finished FS Gang Conduit Bodies and Covers KO Seals Reducing Washers Mulberry Outlet Box Covers New in this catalog: A full line of die-cast, powder painted conduit bodies: 1/2-4, threaded
ALUMINUM OUTLET BODIES
KILLARK GEB SERIES ALUMINUM OUTLET BODIES * Class I, one I, Groups IIC, IIB, IIA Type 4X Applications GEB series conduit boxes are installed in conduit systems within hazardous areas to: Protect conductors
ACP1034CD 100A 3W4P P&S Plug (600VAC/250VDC)
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 ACP1034CD 100A 3W4P P&S Plug (600VAC/250VDC) Appleton/Oz Gedney Catalog Number ACP1034CD Manufacturer Appleton/Oz Gedney
FV Series Nonmetallic Fluorescent Luminaires For Hazardous and Adverse Locations
Applications For use in hazardous locations defined by the NEC and CEC as Class I, Division 2, Groups A, B, C and D; Class II, Division 2, Groups F and G; Marine Outdoor Salt Water; UL1598A and. As well
DISTRIBUTION EQUIPMENT: NEC/CEC HAZARDOUS LOCATION SWITCHES. Application
- and 3-Pole, Non-Interchangeable Trip. Bolted Enclosure Type. Class I, Division 1 and, Groups B, C, D Class II, Division 1 and, Groups E, F, G Application Explosionproof circuit breaker enclosures are
Applications. Standard Materials. Certifications and Compliances
Code Master 2 HID Factory Sealed Luminaires NEC: Class I, Division 1 and 2, Groups C, D Class II, Division 1 and 2, Groups E, F, G Marine Type Electric Fixtures Outside Type (Salt Water) Class I, Division
Commercial Products. New Products in the Commercial Products Product Line
Commercial Products Section A complete solution combining reliability and expertise in every product, providing you with labor and maintenance savings, simplified installation, and improved productivity
Covers for Cast Iron or Aluminum Device Boxes
Single Gang Blank cover for enclosing splices and taps where device not used. Sheet DS100 Flush Sheet steel DSS100 For GFI receptacles. Sheet steel DS23 GFI For square handle general use snap or toggle
ACP6034BC 60A 3W4P P&S Plug (600VAC/250VDC)
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 ACP6034BC 60A 3W4P P&S Plug (600VAC/250VDC) Appleton/Oz Gedney Catalog Number Manufacturer Description Weight per unit
ALPF Factory Sealed Lighting - APPF Power Distribution Panelboards Explosionproof, Dust-Ignitionproof, Watertight
ALPF Factory Sealed Lighting - APPF Power Distribution boards xplosionproof, Dust-Ignitionproof, Watertight NC: Class II, Division 1 and 2, Groups, F, G NA 4, 4X, 7BCD, 9FG Applications Distribution panelboards
Explosion Proof & Hazardous Area Junction Boxes
CSA - Class I Div. 1 - Groups C & D * CSA - Class I Zone 1 - Groups IIA, IIB * * Applies to GUI boxes only Explosion Proof & Hazardous Area Junction Boxes Features: Heavy-duty copper free (below 0.04%)
Kruppsconduit. Metal Raceway Product Range
Kruppsconduit Metal Raceway Product Range CONDUITS (BS4568 & BS31) Index Kruppsconduit 1-10 EMT Conduit 11-25 Rigid Steel Conduit 25-46 PVC Coated Rigid Conduit 47-71 Flexible Conduit System 72-94 CONDUITS
Product Specification Guide Expansion and Deflection Couplings. SECTION Raceway and Boxes for Electrical Systems
Product Specification Guide Expansion and Deflection Couplings SECTION 26 05 33 Raceway and Boxes for Electrical Systems Specifier Notes: Delete any information below in Parts 1, 2 or 3 which is not required
Arktite Circuit Breaking CPS Receptacles and CPP Plugs Delayed Action Factory Sealed
Arktite Circuit Breaking CPS Application: CPS receptacles, angle and straight types, and CPP plugs are used: with portable electrically operated devices such as motor-generator sets, compressors, conveyors,
VIKING SPUR GEAR SINGLE PUMPS SERIES SG-04, SG-05, SG-07 AND SGN-05, SGN-07 STANDARD CONSTRUCTION FEATURES
VIKING SPUR GEAR SINGLE PUMPS FEATURES Section 34 Page 34. SERIES SG-04 and SG-05 Pumps Cutaway View.0 to.2 GPM Sizes (.0 to 2.5 m³/hr) SERIES SG-07 Pump Cutaway View 2.8 to 32.0 GPM Sizes (. to 7 m³/hr)