Combustion. T Alrayyes

Size: px
Start display at page:

Download "Combustion. T Alrayyes"

Transcription

1 Combustion T Alrayyes

2 Fluid motion with combustion chamber Turbulence Swirl SQUISH AND TUMBLE

3

4 Combustion in SI Engines

5 Introduction The combustion in SI engines inside the engine can be divided into three regions 1. Ignition and flame development 2. Flame propagation 3. Flame termination During the flame development period, ignition occurs and the combustion process starts, but very little pressure rise is noticeable and little or no useful work is produced. The vast majority of the burning, incylinder pressure rise and workout occurring at the flame propagation The final 5% (some sources use 10%) of the air-fuel mass which burns is classified as flame termination. During this time, pressure quickly decreases and combustion stops

6 Burning of fuel in a fuel bomb

7

8 Ignition and Flame Development Combustion is initiated by an electrical discharge (plasma discharge)across the electrodes of a spark plug. This occurs anywhere from 10 to 30 before TDC, depending on the geometry of the combustion chamber and the immediate operating conditions of the engine. Flame can generally be detected at about 6 of crank rotation after spark plug firing. When plasma discharge occur, it creates a spherical flame front that propagates outward into the combustion chamber. Combustion starts very slowly because of the high heat losses to the relatively cold spark plug and gas mixture (not enough energy to heat the surrounding). This, in turn, does not raise the cylinder pressure very quickly, and very little compression heating is experienced. It is desirable to have a rich air-fuel mixture around the electrodes of the spark plug at ignition. A rich mixture ignites more readily, has a faster flame speed, and gives a better start to the overall combustion process. Spark plugs are generally located near the intake valves to assure a richer mixture, especially when starting a cold engine.

9 Spark plugs and coils A stoichiometric mixture of hydrocarbon fuel requires about 0.2 mj of energy to ignite selfsustaining combustion. The discharge of a spark plug delivers 30 to 50 mj of energy, most of it is lost by heat transfer Overall spark discharge lasts about second and gives a peak temperature of 60000K and average temperature of 6000K.

10 Applied potential is generally 25,000-40,000 volts, with a maximum current on the order of 200 amps lasting about 10 nsec (1 nsec = 10-9 sec).

11 Most automobiles use a 12-volt electrical system, including a 12-volt battery. There are different methods used to obtain the high voltage required: The low voltage is multiplied many times by the coil that supplies the very high potential delivered to the spark plug. Some systems use a capacitor to discharge across the spark plug electrodes at the proper time Most engine use a magneto driven off the engine crankshaft to generate the needed spark plug voltage

12 Flame propagation in SI engines By the time the first 5-10% of the air-fuel mass has been burned, the combustion process is well established and the flame front moves very quickly through the combustion chamber. Turbulence, swirl, and squish, flame propagation cause the combustion to occur 10 times faster than if there were a laminar flame front moving through a stationary gas mixture. In engines, The flame propagation occurs in an environment where there is a high temperature and pressure, this causes the chemical reaction time to decrease and flame speed to increase.

13 The high temperature and pressure is caused by: 1. Burned gas behind the flame is hotter than the unburned gas in front of the flame. This causes a reduction in unburned gas density compare to the rest of the charge. The decrease in density cause the burned charge to expand in the expense of unburned charge For example, in the figure below, it shows that 30% burned gas occupy 60% of the volume. Compressing 70% of the charge into 40% of the volume. This causes compressive heating 2. Radiation: Radiation emitted from the flame (could be up to 3000 K)further heats the rest of the charge. Temperature rise from radiation further increase the pressure. Convection contribution is minor compare to radiation, due to the short time included in each cycle.

14 Ideally the AFR should be 70% burned by TDC and almost completely burned at about 15 atdc. Thus the combustion in SI engine is almost but not exactly happening at constant volume The close the combustion to constant volume the higher the thermal efficiency However, constant volume combustion is not the best way to operate. A gradual increase combustion pressure might be desirable for smooth transfer of force to the face of the piston (not to damage the piston). An example of the pressure rise rate is 240 kpa/deg In addition to the decrease in thermal efficiency, a slower pressure rise rate might increase the possibility of knock The combustion process is then a compromise between the highest thermal efficiency possible (constant volume)and smooth engine cycle with less efficiency.

15 Flame termination At about 15 to 20 atdc, 90-95% of the air-fuel mass has been combusted. The react of reaction and flame speed will reduce during flame termination. And the combustion end up slowly dying out The reaction is happening at small volume in the corners of the combustion chamber and a long the chamber wall, mainly pushed by the burned gas (Although the cylinder start to expand). Near the walls, turbulence and mass motion of the gas mixture has been dampened out and there is a stagnant boundary layer. the large mass of metal wall will act as a sink and conduct away much of the energy being released in the reaction flame. During the flame termination period, self ignition will occur in the end gas in front of the flame front This knock might not much of an effect since most of the fuel has already burned out.

16 Factors influencing combustion Spark timing Engine speed Equivalence ratio Residual gas fraction Compression ratio Combustion chamber design

17 Spark timing Spark timing must be located relative to the TDC to obtain max power or torque. Combined duration of the flame development and propagation process is typically between 30 and 90 CA degrees. If the start of combustion process is too advanced before TDC, compression stroke work transfer (from piston to cylinder gases or negative work) increases. If the end of combustion process is delayed by retarding the spark timing, peak cylinder pressure occurs later in the expansion stroke and is reduced in magnitude. These changes reduce the expansion stroke work transfer from cylinder gases to the piston. The optimum timing which gives maximum brake torque (called maximum brake torque or MBT timing) occurs when magnitude of these two opposing trends just offset each other.

18 Engine Speed Mixture burning rate is strongly influenced by engine speed. 4 Flame speed (m/s) increases with engine speed due to the higher turbulence, swirl, and squish. Although flame speed increases, the duration of combustion in crank angle degrees might increase slightly with increasing engine speed. Increase of the engine speed, reduces the time available for a complete combustion. To compensate this, ignition timing should be adjusted spark advance is increased with increasing engine speed.

19 Mixture properties The fuel-air equivalence ratio affects the burning rate. Lean mixtures have slower flame speeds, as shown in Figure. Slightly rich mixtures have the fastest flame speeds, with the maximum for most fuels occurring at an equivalence ratio near 1.2. Burning rate reduces for richer and leaner mixtures. The burned gas fraction in the unburned mixture, due to the residual gas fraction and any recycled exhaust gases (EGR), slows down both flame development and propagation. Fuel composition changes can be significant. Faster burning engines (high turbulence) are less sensitive to changes in mixture composition, p and T than slower burning engines.

20

21 Compression Ratio Increase in CR increases the p and T of the charge at ignition, Reduces the mass fraction of the residual gases Both are favourable conditions for ignition which reduces the first stage of combustion, and increases flame propagation rate in the main stage. Increasing CR, increases Area/Volume ratio of the cylinder, increasing the cooling effects and the quench layers. Final stage of combustion is increased.

22 Combustion Chamber Design Intake manifold design and combustion chamber shape effects the gas. flow and turbulence intensity. Turbulence strongly effects burning rate of the fuel. Spark plug location effects distance travelled by the flame and flame front surface area. Number of spark plugs.

23

24 Abnormal combustion Fuel composition, engine design and operating parameters, combustion chamber deposits may prevent occurring of the normal combustion process. There are two types of abnormal combustion : Knock Surface ignition

25 Knock Knock is the autoignition of the portion of fuel, air and residual gas mixture ahead of the advancing flame, that produces a noise. As the flame propagates across combustion chamber, end gas is compressed causing pressure, temperature and density to increase. Some of the end gas fuel-air mixture may undergo chemical reactions before normal combustion causing autoignition End gases then burn very rapidly releasing energy at a rate 5 to 25 times in comparison to normal combustion. This causes high frequency pressure oscillations inside the cylinder that produce sharp metallic noise called knock. Knock will not occur when the flame front consumes the end gas before these reactions have time to cause fuel-air mixture to autoignite. Knock will occur if the precombustion reactions produce autoignition before the flame front arrives

26 Surface Ignition Surface ignition is ignition of the fuel-air charge by any source other than the spark plug, for example: overheated valves spark plugs, by glowing combustion chamber deposits or by any other hot spot in the engine combustion chamber It may occur before the spark plug ignites the charge (preignition) or after normal ignition (postignition). It may produce a single flame or many flames. Surface ignition may result in knock.

27 Design Parameters to control knock Compression ratio increase in CR increases thermal efficiency but also increases the tendancy to knock - limits engine performance. Combustion chamber size and shape as combustion chamber volume gets smaller, surface area-to-volume ratio increases providing efficient cooling, reduces tendency to knock. In SI-engines max piston diameter is limited to 150 mm Flame propagation distance (chamber shape and spark plug location, number of spark plugs used) also effects knock Valve overlap Decrease overlap will reduce residual gases, produces cooling effect - reduces knock tendency Engine cooling efficient cooling reduces tendancy to knock - water cooling systems are more effective, in aircooled engines CR is limited

28 Operating Parameters Equivalence ratio Autoignition reactions occur at slightly lean mixtures - flame speed is lower (more time for autoignition to happen), pre-reaction duration is relatively short. Lean and rich mixtures - tendancy to knock is reduced. Spark advance Increasing spark advance, p and T increases, flame speed also increases reducing the time for pre-reactions, However tendancy to knock increases with increasing spark advance. Oxygen concentration in combustion chamber decreasing oxygen concentration reduces the tendency to knock humidity of intake air also cools the charge and reduces knocking tendency. Cooling water temperature cooling water T effects mean combustion chamber temperatures - tendancy to knock decreases with decrease in T

29 Variation in combustion Ideally, combustion in every cylinder of an engine would be exactly the same In addition, ideally, there would be no cycle-to-cycle variation in anyone cylinder. Unfortunately, this is not the case and there is both a cycle to cycle variation within the cylinder and variation between the different cylinders.

30 Reason for the variation between cylinders Length and geometry of intake manifold (change in the volumetric efficiency and AFR) Temperature difference in the runners (cause variation in evaporation rate and subsequently volumetric efficiency) Evaporative cooling Different components of gasoline EGR introduction Most of the above reasons will be mainly for carburettors systems and throttle position fuel injector The main reason for the variation in multipoint injectors and incylinder injection is fuel injected.

31 In cylinder variation: AFR variation between cycles (standard deviation is between 2 to 6%) Turbulence variation Incomplete mixing especially near the spark plug (cause a variation in the start of the combustion which will affect the subsequent combustion) Fast burn in about twice the slow burn The greatest percentage differences occur at light engine loads and low speeds, with idle being the worst condition.

32

33 As a compromise, the average burn time is used to set the engine operating conditions (i.e., spark timing, AF, compression ratio, etc.). This lowers the output of the engine from what could be obtained if all cylinders and all cycles had exactly the same combustion process. A cycle in which fast burn occurs is like a cycle with an over-advanced spark. This happens when there is a rich AF ratio, higher than average turbulence, and good initial combustion startup The result of this is a temperature and pressure rise too early in the cycle, with a good chance of knock occurring. This limits the compression ratio and fuel octane number that can be tolerated for a given engine.

34 A cycle with a slower than average burn time is like a cycle with a retarded spark. This occurs when there is a lean mixture and higher than average EGR. The result of this is a flame lasting well into the power stroke. This is when partial burns and misfires occur Higher heat loss occurs because of the longer combustion time and because the flame front is wider with the slower burning lean mixture. For smooth operation, engine conditions must be set for the worst cyclic variations in the worst cylinder If all cylinders had the exact same combustion process cycle after cycle, a higher engine compression ratio could e tolerated, and the air-fuel ratio could be set for higher power and greater fuel economy. Cheaper, lower octane fuel could be used.

35 Combustion in CI engines

36 Combustion in CI Engine Combustion in a compression ignition engine is quite different from that in an SI engine. Whereas combustion in an SI engine is essentially a flame front moving through a homogeneous mixture. combustion in a CI engine is an unsteady process occurring simultaneously at many spots in a very nonhomogeneous mixture at a rate controlled by fuel injection. Air intake into the engine is unthrottled, with engine torque and power output controlled by the amount of fuel injected per cycle. Because the incoming air is not throttled, pressure in the intake manifold is consistently at a value close to one atmosphere. This makes the pump work loop of the engine cycle shown very small

37 Compression ratios of modern CI engines range from 12 to 24. Higher compression ratio increase thermal efficiency However, because the overall air-fuel ratio on which CI engines operate is quite lean (equivalence ratio = 0.8), less brake power output is often obtained for a given engine displacement.# Only air is contained in the cylinder during the compression stroke. Fuel is injected into the cylinders late in the compression stroke by one or more injectors located in each cylinder combustion chamber. Injection time is usually about 20 of crankshaft rotation, starting at about 15 btdc and ending about 5 atdc. Ignition delay is fairly constant in real time, so at higher engine speeds fuel injection must be started slightly earlier in the cycle.

38 The fuel must go through a series of events to assure the proper combustion process: 1. Atomization. Fuel drops break into very small droplets. The smaller the original drop size emitted by the injector, the quicker and more efficient will be this atomization process. 2. Vaporization. The small droplets of liquid fuel evaporate to vapor. This occurs very quickly due to the hot air temperatures created by the high compression of CI engines. High air temperature needed for this vaporization process requires a minimum compression ratio in CI engines of about 12:1. About 90% of the fuel injected into the cylinder has been vaporized within second after injection.

39 Liquid Atomization at High Speeds

40 3. Mixing: After vaporization, the fuel vapour must mix with air to form a mixture within the AF range which is combustible. This mixing is happening because of the high fuel injection velocity added to the swirl and turbulence in the cylinder. Combustion can occur within the equivalence ratio limits of Φ = 1.8 (rich) and Φ = 0.8 (lean). Figure 7-15 shows the non-homogeneous distribution of air-fuel ratio that develops around the injected fuel jet.

41

42 4. Self-Ignition: At about 8 btdc, 6 to 8 after the start of injection, the air-fuel mixture starts to self-ignite. Before actual combustion, a secondary reaction is occurring which includes breakdown of large hydrocarbon molecules into smaller species and some oxidation These reactions, caused by the high-temperature air, are exothermic and further raise the air temperature. This finally leads to an actual sustained combustion process.

43 5. Combustion starts from self-ignition simultaneously at many locations in the slightly rich zone of the fuel jet, where the equivalence ratio is Φ= 1 to 1.5 (zone B in Fig. 7-15). At this time, somewhere between 70% and 95% of the fuel in the combustion chamber is in the vapour state. When combustion starts, multiple flame fronts spreading from the many selfignition sites quickly consume all the gas mixture which is in a correct combustible air-fuel ratio, even where self-ignition wouldn't occur. Combustion cause an increase in temperature and pressure inside the engine. This increase will create a good environement for combustion even in areas where self ignition didn t start. The combustion last between 50 to 60 more than the 20 injection duration. This is because some fuel particles takes longer to mix into a combustible mixture.] 60% of the fuel is burned in the first third of the combustion Burning rate increase with increasing speed, so the burn angle remain about constant

44

45 Ignition delay, ID The period between the start of fuel injection into the combustion chamber and the start of combustion is termed as ignition delay period. Physical Factors Affecting Ignition Delay: In cylinder pressure, temperature An increase in temperature, pressure will decrease ID time. Engine speed An increase Engine speed will decrease ignition delay time Engine speed increases the air motion and turbulence, reduces ID time slightly (in ms), in terms of CA degrees ID increases almost linearly. Injection quantity (load) Reducing engine load changes AFR, cools down the engine, reduces wall temperatures, reduces residual gas temperatures and increase ID.

46 Injection timing: If injection is too early, ignition delay time will increase because temperature and pressure will be lower. If injection is late, the piston will move past TDC, pressure and temperature will decrease, and again ignition delay time will increase. Combustion chamber design Spray impingement on the walls effect fuel evaporation and ID increase increase compression ratio, increase p and T and reduces ID Reducing stroke volume, increase surface area to volume ratio, increase engine cooling and increase ID Swirl rate Change vaporisation rate and air-fuel mixing - under normal operating conditions the effect is small. At start-up (low engine speed and temperature) more important, high rate of evaporation and mixing is obtained by swirl Oxygen concentration Residual gases reduce O2 concentration and reducing oxygen concentration increases ID

47 Cetane number Both physical and chemical properties of the fuel is important. Ignition quality of the fuel is defined by its cetane number. It is important to use fuel with the correct cetane number for a given engine. If the cetane number is low, ignition delay will be too long, and a more-thandesirable amount of fuel will be injected into the cylinder before combustion starts. When combustion then does start, a greater amount of fuel will be quickly consumed, and the initial cylinder pressure rise will be greater. This causes a very large initial force applied to the piston face and a rough engine cycle. If the cetane number is high, combustion will start too early before TDC, with a resulting loss in engine power. Cetane number can be changed by blending small amounts of certain additives to the fuel. Additives that accelerate ignition include nitrites, nitrates, organic peroxides, and some sulfur compounds

48 Cold-Weather Problems in CI engines Starting a cold CI engine can be very difficult. The cold environment cause longer ignition delay time and even in some cause failure to start. The failure to start is mainly due lower self ignition temperature The lower temperature is caused by: Low air and fuel temperature Low cold metal cylinder wall High oil viscosity.

49 Lubrication oil and cold start: Lubrication oil is cold, its viscosity is high, and distribution is limited. The starter motor has to turn the cold engine that is poorly lubricated with very high viscosity oil. This results in a slower than normal turnover speed to start the engine. The slower than normal rotation of the engine, combined with the cold metal cylinder walls, promotes a large heat loss to the walls and keeps the air temperature below that needed to self-ignite the fuel.

50 Methods to promote cold start Glow plug Glow plug is the mostly common used method to promote cold start. A glow plug is a simple resistance heater connected to a battery with the heated surface located within the combustion chamber of the engine. For a short time, seconds, before starting the engine, the glow plug is turned on and the resistor becomes red hot. Now, when the engine is started, combustion in the first few cycles is not ignited by compressive heating but by surface ignition off the glow plug.

51 The pony engine Because of the large amount of energy needed to rotate and start very large CI engines that are cold, using an electric motor powered from a battery is sometimes not practical. Instead, a small internal combustion engine can be used as the starting motor for the larger engine. The pony engine is first started and then used to turn over the large engine by engaging it to the flywheel of the large engine. The pony engine is then disengaged when the large engine is started. Higher compression ratio engine To aid in cold starting, many medium-size CI engines are built with a higher compression ratio than would otherwise be needed. Some are also given a larger flywheel for this purpose.

52

53

54 Preheating the lubricating oil Preheating the lubricating oil electrically is done on some engines to help the starting process. Some systems even distribute the oil throughout the engine before starting by means of an electric oil pump Late injection and a richer air-fuel mixture Late injection and a richer air-fuel mixture are also used to aid starting. Continuous Running It is not an uncommon practice to leave large CI engines running continuously during cold weather to avoid the problem of restarting them.

Dr Ali Jawarneh Department of Mechanical Engineering

Dr Ali Jawarneh Department of Mechanical Engineering Chapter 7: Combustion Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University Outline In this lecture we will discuss the combustion process: The characteristics of the process. The different

More information

Normal vs Abnormal Combustion in SI engine. SI Combustion. Turbulent Combustion

Normal vs Abnormal Combustion in SI engine. SI Combustion. Turbulent Combustion Turbulent Combustion The motion of the charge in the engine cylinder is always turbulent, when it is reached by the flame front. The charge motion is usually composed by large vortexes, whose length scales

More information

COMBUSTION in SI ENGINES

COMBUSTION in SI ENGINES Internal Combustion Engines MAK 493E COMBUSTION in SI ENGINES Prof.Dr. Cem Soruşbay Istanbul Technical University Internal Combustion Engines MAK 493E Combustion in SI Engines Introduction Classification

More information

COMBUSTION in SI ENGINES

COMBUSTION in SI ENGINES Internal Combustion Engines ME422 COMBUSTION in SI ENGINES Prof.Dr. Cem Soruşbay Internal Combustion Engines Combustion in SI Engines Introduction Classification of the combustion process Normal combustion

More information

Module7:Advanced Combustion Systems and Alternative Powerplants Lecture 32:Stratified Charge Engines

Module7:Advanced Combustion Systems and Alternative Powerplants Lecture 32:Stratified Charge Engines ADVANCED COMBUSTION SYSTEMS AND ALTERNATIVE POWERPLANTS The Lecture Contains: DIRECT INJECTION STRATIFIED CHARGE (DISC) ENGINES Historical Overview Potential Advantages of DISC Engines DISC Engine Combustion

More information

ACTUAL CYCLE. Actual engine cycle

ACTUAL CYCLE. Actual engine cycle 1 ACTUAL CYCLE Actual engine cycle Introduction 2 Ideal Gas Cycle (Air Standard Cycle) Idealized processes Idealize working Fluid Fuel-Air Cycle Idealized Processes Accurate Working Fluid Model Actual

More information

Module 3: Influence of Engine Design and Operating Parameters on Emissions Lecture 14:Effect of SI Engine Design and Operating Variables on Emissions

Module 3: Influence of Engine Design and Operating Parameters on Emissions Lecture 14:Effect of SI Engine Design and Operating Variables on Emissions Module 3: Influence of Engine Design and Operating Parameters on Emissions Effect of SI Engine Design and Operating Variables on Emissions The Lecture Contains: SI Engine Variables and Emissions Compression

More information

Heat Transfer in Engines. Internal Combustion Engines

Heat Transfer in Engines. Internal Combustion Engines Heat Transfer in Engines Internal Combustion Engines Energy Distribution Removing heat is critical in keeping an engine and lubricant from thermal failure Amount of energy available for use: Brake thermal

More information

AE 1005 AUTOMOTIVE ENGINES COMBUSTION IN SI ENGINES

AE 1005 AUTOMOTIVE ENGINES COMBUSTION IN SI ENGINES AE 1005 AUTOMOTIVE ENGINES COMBUSTION IN SI ENGINES Syllabus Combustion in premixed and diffusion flames - Combustion process in IC engines. Stages of combustion - Flame propagation - Flame velocity and

More information

Lecture 5. Abnormal Combustion

Lecture 5. Abnormal Combustion Lecture 5 Abnormal Combustion Abnormal Combustion The Abnormal Combustion:- When the combustion gets deviated from the normal behavior resulting loss of performance or damage to the engine. It is happened

More information

Figure 1: The spray of a direct-injecting four-stroke diesel engine

Figure 1: The spray of a direct-injecting four-stroke diesel engine MIXTURE FORMATION AND COMBUSTION IN CI AND SI ENGINES 7.0 Mixture Formation in Diesel Engines Diesel engines can be operated both in the two-stroke and four-stroke process. Diesel engines that run at high

More information

Module 2:Genesis and Mechanism of Formation of Engine Emissions Lecture 3: Introduction to Pollutant Formation POLLUTANT FORMATION

Module 2:Genesis and Mechanism of Formation of Engine Emissions Lecture 3: Introduction to Pollutant Formation POLLUTANT FORMATION Module 2:Genesis and Mechanism of Formation of Engine Emissions POLLUTANT FORMATION The Lecture Contains: Engine Emissions Typical Exhaust Emission Concentrations Emission Formation in SI Engines Emission

More information

Alternative Fuels & Advance in IC Engines

Alternative Fuels & Advance in IC Engines Alternative Fuels & Advance in IC Engines IIT Kanpur Kanpur, India (208016) Combustion in SI Engine Course Instructor Dr. Avinash Kumar Agarwal Professor Department of Mechanical Engineering Indian Institute

More information

Chapter 4 ANALYTICAL WORK: COMBUSTION MODELING

Chapter 4 ANALYTICAL WORK: COMBUSTION MODELING a 4.3.4 Effect of various parameters on combustion in IC engines: Compression ratio: A higher compression ratio increases the pressure and temperature of the working mixture which reduce the initial preparation

More information

Module 2:Genesis and Mechanism of Formation of Engine Emissions Lecture 9:Mechanisms of HC Formation in SI Engines... contd.

Module 2:Genesis and Mechanism of Formation of Engine Emissions Lecture 9:Mechanisms of HC Formation in SI Engines... contd. Mechanisms of HC Formation in SI Engines... contd. The Lecture Contains: HC from Lubricating Oil Film Combustion Chamber Deposits HC Mixture Quality and In-Cylinder Liquid Fuel HC from Misfired Combustion

More information

is the crank angle between the initial spark and the time when about 10% of the charge is burned. θ θ

is the crank angle between the initial spark and the time when about 10% of the charge is burned. θ θ ME 410 Day 30 Phases of Combustion 1. Ignition 2. Early flame development θd θ 3. Flame propagation b 4. Flame termination The flame development angle θd is the crank angle between the initial spark and

More information

Engine Cycles. T Alrayyes

Engine Cycles. T Alrayyes Engine Cycles T Alrayyes Introduction The cycle experienced in the cylinder of an internal combustion engine is very complex. The cycle in SI and diesel engine were discussed in detail in the previous

More information

Internal combustion engines can be classified in a number of different ways: 1. Types of Ignition

Internal combustion engines can be classified in a number of different ways: 1. Types of Ignition Chapter 1 Introduction 1-3 ENGINE CLASSIFICATIONS Internal combustion engines can be classified in a number of different ways: 1. Types of Ignition 1 (a) Spark Ignition (SI). An SI engine starts the combustion

More information

INFLUENCE OF FUEL TYPE AND INTAKE AIR PROPERTIES ON COMBUSTION CHARACTERISTICS OF HCCI ENGINE

INFLUENCE OF FUEL TYPE AND INTAKE AIR PROPERTIES ON COMBUSTION CHARACTERISTICS OF HCCI ENGINE ENGINEERING FOR RURAL DEVELOPMENT Jelgava, 23.-24.5.213. INFLUENCE OF FUEL TYPE AND INTAKE AIR PROPERTIES ON COMBUSTION CHARACTERISTICS OF HCCI ENGINE Kastytis Laurinaitis, Stasys Slavinskas Aleksandras

More information

Theoretical Study of the effects of Ignition Delay on the Performance of DI Diesel Engine

Theoretical Study of the effects of Ignition Delay on the Performance of DI Diesel Engine Theoretical Study of the effects of Ignition Delay on the Performance of DI Diesel Engine Vivek Shankhdhar a, Neeraj Kumar b a M.Tech Scholar, Moradabad Institute of Technology, India b Asst. Proff. Mechanical

More information

5. Control System CONTROL SYSTEM FUEL INJECTION (FUEL SYSTEM) A: GENERAL FU(H4DOTC)-29

5. Control System CONTROL SYSTEM FUEL INJECTION (FUEL SYSTEM) A: GENERAL FU(H4DOTC)-29 W1860BE.book Page 29 Tuesday, January 28, 2003 11:01 PM 5. Control System A: GENERAL The ECM receives signals from various sensors, switches, and other control modules. Using these signals, it determines

More information

Internal Combustion Engines

Internal Combustion Engines Emissions & Air Pollution Lecture 3 1 Outline In this lecture we will discuss emission control strategies: Fuel modifications Engine technology Exhaust gas aftertreatment We will become particularly familiar

More information

5. Control System CONTROL SYSTEM FUEL INJECTION (FUEL SYSTEM) A: GENERAL. FU(STi)-27

5. Control System CONTROL SYSTEM FUEL INJECTION (FUEL SYSTEM) A: GENERAL. FU(STi)-27 W1860BE.book Page 27 Tuesday, January 28, 2003 11:01 PM 5. Control System A: GENERAL The ECM receives signals from various sensors, switches, and other control modules. Using these signals, it determines

More information

COVENANT UNIVERSITY NIGERIA TUTORIAL KIT OMEGA SEMESTER PROGRAMME: MECHANICAL ENGINEERING

COVENANT UNIVERSITY NIGERIA TUTORIAL KIT OMEGA SEMESTER PROGRAMME: MECHANICAL ENGINEERING COVENANT UNIVERSITY NIGERIA TUTORIAL KIT OMEGA SEMESTER PROGRAMME: MECHANICAL ENGINEERING COURSE: MCE 320 DISCLAIMER The contents of this document are intended for practice and leaning purposes at the

More information

UNIT IV INTERNAL COMBUSTION ENGINES

UNIT IV INTERNAL COMBUSTION ENGINES UNIT IV INTERNAL COMBUSTION ENGINES Objectives After the completion of this chapter, Students 1. To know the different parts of IC engines and their functions. 2. To understand the working principle of

More information

ADDIS ABABA UNIVERSITY INSTITUTE OF TECHNOLOGY

ADDIS ABABA UNIVERSITY INSTITUTE OF TECHNOLOGY 1 INTERNAL COMBUSTION ENGINES ADDIS ABABA UNIVERSITY INSTITUTE OF TECHNOLOGY MECHANICAL ENGINEERING DEPARTMENT DIVISON OF THERMAL AND ENERGY CONVERSION IC Engine Fundamentals 2 Engine Systems An engine

More information

LECTURE NOTES INTERNAL COMBUSTION ENGINES SI AN INTEGRATED EVALUATION

LECTURE NOTES INTERNAL COMBUSTION ENGINES SI AN INTEGRATED EVALUATION LECTURE NOTES on INTERNAL COMBUSTION ENGINES SI AN INTEGRATED EVALUATION Integrated Master Course on Mechanical Engineering Mechanical Engineering Department November 2015 Approach SI _ indirect injection

More information

Powertrain Efficiency Technologies. Turbochargers

Powertrain Efficiency Technologies. Turbochargers Powertrain Efficiency Technologies Turbochargers Turbochargers increasingly are being used by automakers to make it possible to use downsized gasoline engines that consume less fuel but still deliver the

More information

A Study of EGR Stratification in an Engine Cylinder

A Study of EGR Stratification in an Engine Cylinder A Study of EGR Stratification in an Engine Cylinder Bassem Ramadan Kettering University ABSTRACT One strategy to decrease the amount of oxides of nitrogen formed and emitted from certain combustion devices,

More information

Internal Combustion Engines

Internal Combustion Engines Air and Fuel Induction Lecture 3 1 Outline In this lecture we will discuss the following: A/F mixture preparation in gasoline engines using carburetion. Air Charging technologies: Superchargers Turbochargers

More information

2) Rich mixture: A mixture which contains less air than the stoichiometric requirement is called a rich mixture (ex. A/F ratio: 12:1, 10:1 etc.

2) Rich mixture: A mixture which contains less air than the stoichiometric requirement is called a rich mixture (ex. A/F ratio: 12:1, 10:1 etc. Unit 3. Carburettor University Questions: 1. Describe with suitable sketches : Main metering system and Idling system 2. Draw the neat sketch of a simple carburettor and explain its working. What are the

More information

CHAPTER 8 EFFECTS OF COMBUSTION CHAMBER GEOMETRIES

CHAPTER 8 EFFECTS OF COMBUSTION CHAMBER GEOMETRIES 112 CHAPTER 8 EFFECTS OF COMBUSTION CHAMBER GEOMETRIES 8.1 INTRODUCTION Energy conservation and emissions have become of increasing concern over the past few decades. More stringent emission laws along

More information

Focus on Training Section: Unit 2

Focus on Training Section: Unit 2 All Pump Types Page 1 1. Title Page Learning objectives Become familiar with the 4 stroke cycle Become familiar with diesel combustion process To understand how timing affects emissions To understand the

More information

SI engine combustion

SI engine combustion SI engine combustion 1 SI engine combustion: How to burn things? Reactants Products Premixed Homogeneous reaction Not limited by transport process Fast/slow reactions compared with other time scale of

More information

AN EXPERIMENT STUDY OF HOMOGENEOUS CHARGE COMPRESSION IGNITION COMBUSTION AND EMISSION IN A GASOLINE ENGINE

AN EXPERIMENT STUDY OF HOMOGENEOUS CHARGE COMPRESSION IGNITION COMBUSTION AND EMISSION IN A GASOLINE ENGINE THERMAL SCIENCE: Year 2014, Vol. 18, No. 1, pp. 295-306 295 AN EXPERIMENT STUDY OF HOMOGENEOUS CHARGE COMPRESSION IGNITION COMBUSTION AND EMISSION IN A GASOLINE ENGINE by Jianyong ZHANG *, Zhongzhao LI,

More information

EFFECT OF INJECTION ORIENTATION ON EXHAUST EMISSIONS IN A DI DIESEL ENGINE: THROUGH CFD SIMULATION

EFFECT OF INJECTION ORIENTATION ON EXHAUST EMISSIONS IN A DI DIESEL ENGINE: THROUGH CFD SIMULATION EFFECT OF INJECTION ORIENTATION ON EXHAUST EMISSIONS IN A DI DIESEL ENGINE: THROUGH CFD SIMULATION *P. Manoj Kumar 1, V. Pandurangadu 2, V.V. Pratibha Bharathi 3 and V.V. Naga Deepthi 4 1 Department of

More information

VALVE TIMING DIAGRAM FOR SI ENGINE VALVE TIMING DIAGRAM FOR CI ENGINE

VALVE TIMING DIAGRAM FOR SI ENGINE VALVE TIMING DIAGRAM FOR CI ENGINE VALVE TIMING DIAGRAM FOR SI ENGINE VALVE TIMING DIAGRAM FOR CI ENGINE Page 1 of 13 EFFECT OF VALVE TIMING DIAGRAM ON VOLUMETRIC EFFICIENCY: Qu. 1:Why Inlet valve is closed after the Bottom Dead Centre

More information

I.C Engine Topic: Fuel supply systems Part-1

I.C Engine Topic: Fuel supply systems Part-1 I.C Engine Topic: Fuel supply systems Part-1 By: Prof.Kunalsinh Kathia Essential parts of carburetor Fuel strainer Float chamber Metering and idiling system Choke and throttle Fuel strainer As gasoline

More information

Which are the four important control loops of an spark ignition (SI) engine?

Which are the four important control loops of an spark ignition (SI) engine? 151-0567-00 Engine Systems (HS 2017) Exercise 1 Topic: Lecture 1 Johannes Ritzmann (jritzman@ethz.ch), Raffi Hedinger (hraffael@ethz.ch); October 13, 2017 Problem 1 (Control Systems) Why do we use control

More information

Internal Combustion Engines

Internal Combustion Engines Internal Combustion Engines The internal combustion engine is an engine in which the burning of a fuel occurs in a confined space called a combustion chamber. This exothermic reaction of a fuel with an

More information

CONTROLLING COMBUSTION IN HCCI DIESEL ENGINES

CONTROLLING COMBUSTION IN HCCI DIESEL ENGINES CONTROLLING COMBUSTION IN HCCI DIESEL ENGINES Nicolae Ispas *, Mircea Năstăsoiu, Mihai Dogariu Transilvania University of Brasov KEYWORDS HCCI, Diesel Engine, controlling, air-fuel mixing combustion ABSTRACT

More information

8 th International Symposium TCDE Choongsik Bae and Sangwook Han. 9 May 2011 KAIST Engine Laboratory

8 th International Symposium TCDE Choongsik Bae and Sangwook Han. 9 May 2011 KAIST Engine Laboratory 8 th International Symposium TCDE 2011 Choongsik Bae and Sangwook Han 9 May 2011 KAIST Engine Laboratory Contents 1. Background and Objective 2. Experimental Setup and Conditions 3. Results and Discussion

More information

Engine Heat Transfer. Engine Heat Transfer

Engine Heat Transfer. Engine Heat Transfer Engine Heat Transfer 1. Impact of heat transfer on engine operation 2. Heat transfer environment 3. Energy flow in an engine 4. Engine heat transfer Fundamentals Spark-ignition engine heat transfer Diesel

More information

STATE OF THE ART OF PLASMATRON FUEL REFORMERS FOR HOMOGENEOUS CHARGE COMPRESSION IGNITION ENGINES

STATE OF THE ART OF PLASMATRON FUEL REFORMERS FOR HOMOGENEOUS CHARGE COMPRESSION IGNITION ENGINES Bulletin of the Transilvania University of Braşov Vol. 3 (52) - 2010 Series I: Engineering Sciences STATE OF THE ART OF PLASMATRON FUEL REFORMERS FOR HOMOGENEOUS CHARGE COMPRESSION IGNITION ENGINES R.

More information

INFLUENCE OF INTAKE AIR TEMPERATURE AND EXHAUST GAS RECIRCULATION ON HCCI COMBUSTION PROCESS USING BIOETHANOL

INFLUENCE OF INTAKE AIR TEMPERATURE AND EXHAUST GAS RECIRCULATION ON HCCI COMBUSTION PROCESS USING BIOETHANOL ENGINEERING FOR RURAL DEVELOPMENT Jelgava, 2.-27..216. INFLUENCE OF INTAKE AIR TEMPERATURE AND EXHAUST GAS RECIRCULATION ON HCCI COMBUSTION PROCESS USING BIOETHANOL Kastytis Laurinaitis, Stasys Slavinskas

More information

Marc ZELLAT, Driss ABOURI, Thierry CONTE and Riyad HECHAICHI CD-adapco

Marc ZELLAT, Driss ABOURI, Thierry CONTE and Riyad HECHAICHI CD-adapco 16 th International Multidimensional Engine User s Meeting at the SAE Congress 2006,April,06,2006 Detroit, MI RECENT ADVANCES IN SI ENGINE MODELING: A NEW MODEL FOR SPARK AND KNOCK USING A DETAILED CHEMISTRY

More information

Module 5: Emission Control for SI Engines Lecture20:ADD-ON SYSTEMS FOR CONTROL OF ENGINE-OUT EMISSIONS

Module 5: Emission Control for SI Engines Lecture20:ADD-ON SYSTEMS FOR CONTROL OF ENGINE-OUT EMISSIONS ADD-ON SYSTEMS FOR CONTROL OF ENGINE-OUT EMISSIONS The Lecture Contains: Crankcase Emission Control (PCV System) Evaporative Emission Control Exhaust Gas Recirculation Water Injection file:///c /...%20and%20Settings/iitkrana1/My%20Documents/Google%20Talk%20Received%20Files/engine_combustion/lecture20/20_1.htm[6/15/2012

More information

Kul Internal Combustion Engine Technology. Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5

Kul Internal Combustion Engine Technology. Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5 Kul-14.4100 Internal Combustion Engine Technology Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5 Definitions Combustion engines convert the chemical energy of fuel to mechanical

More information

MIXTURE FORMATION IN SPARK IGNITION ENGINES. Chapter 5

MIXTURE FORMATION IN SPARK IGNITION ENGINES. Chapter 5 MIXTURE FORMATION IN SPARK IGNITION ENGINES Chapter 5 Mixture formation in SI engine Engine induction and fuel system must prepare a fuel-air mixture that satisfiesthe requirements of the engine over its

More information

Basic Requirements. ICE Fuel Metering. Mixture Quality Requirements. Requirements for Metering & Mixing

Basic Requirements. ICE Fuel Metering. Mixture Quality Requirements. Requirements for Metering & Mixing Basic Requirements ICE Fuel Metering Dr. M. Zahurul Haq Professor Department of Mechanical Engineering Bangladesh University of Engineering & Technology (BUET) Dhaka-1000, Bangladesh zahurul@me.buet.ac.bd

More information

PERFORMANCE AND EMISSION ANALYSIS OF DIESEL ENGINE BY INJECTING DIETHYL ETHER WITH AND WITHOUT EGR USING DPF

PERFORMANCE AND EMISSION ANALYSIS OF DIESEL ENGINE BY INJECTING DIETHYL ETHER WITH AND WITHOUT EGR USING DPF PERFORMANCE AND EMISSION ANALYSIS OF DIESEL ENGINE BY INJECTING DIETHYL ETHER WITH AND WITHOUT EGR USING DPF PROJECT REFERENCE NO. : 37S1036 COLLEGE BRANCH GUIDES : KS INSTITUTE OF TECHNOLOGY, BANGALORE

More information

Homogeneous Charge Compression Ignition combustion and fuel composition

Homogeneous Charge Compression Ignition combustion and fuel composition Loughborough University Institutional Repository Homogeneous Charge Compression Ignition combustion and fuel composition This item was submitted to Loughborough University's Institutional Repository by

More information

Lambda Control Fuel Adaptation and Fuel Trim

Lambda Control Fuel Adaptation and Fuel Trim Lambda Control Fuel Adaptation and Fuel Trim Q: What is Lambda and Lambda Control? A: In the case of a gasoline engine, the optimal mixture of air to fuel for complete combustion is a ratio of 14.7 parts

More information

Emission from gasoline powered vehicles are classified as 1. Exhaust emission 2. Crank case emission 3. Evaporative emission. Table 1.

Emission from gasoline powered vehicles are classified as 1. Exhaust emission 2. Crank case emission 3. Evaporative emission. Table 1. Introduction: Main three types of automotive vehicle being used 1. Passenger cars powered by four stroke gasoline engines 2. Motor cycles, scooters and auto rickshaws powered mostly by small two stroke

More information

Combustion Equipment. Combustion equipment for. Solid fuels Liquid fuels Gaseous fuels

Combustion Equipment. Combustion equipment for. Solid fuels Liquid fuels Gaseous fuels Combustion Equipment Combustion equipment for Solid fuels Liquid fuels Gaseous fuels Combustion equipment Each fuel type has relative advantages and disadvantages. The same is true with regard to firing

More information

Foundations of Thermodynamics and Chemistry. 1 Introduction Preface Model-Building Simulation... 5 References...

Foundations of Thermodynamics and Chemistry. 1 Introduction Preface Model-Building Simulation... 5 References... Contents Part I Foundations of Thermodynamics and Chemistry 1 Introduction... 3 1.1 Preface.... 3 1.2 Model-Building... 3 1.3 Simulation... 5 References..... 8 2 Reciprocating Engines... 9 2.1 Energy Conversion...

More information

REVIEW ON GASOLINE DIRECT INJECTION

REVIEW ON GASOLINE DIRECT INJECTION International Journal of Aerospace and Mechanical Engineering REVIEW ON GASOLINE DIRECT INJECTION Jayant Kathuria B.Tech Automotive Design Engineering jkathuria97@gmail.com ABSTRACT Gasoline direct-injection

More information

ENGINE & WORKING PRINCIPLES

ENGINE & WORKING PRINCIPLES ENGINE & WORKING PRINCIPLES A heat engine is a machine, which converts heat energy into mechanical energy. The combustion of fuel such as coal, petrol, diesel generates heat. This heat is supplied to a

More information

EEN-E2002 Combustion Technology 2017 LE 3 answers

EEN-E2002 Combustion Technology 2017 LE 3 answers EEN-E2002 Combustion Technology 2017 LE 3 answers 1. Plot the following graphs from LEO-1 engine with data (Excel_sheet_data) attached on my courses? (12 p.) a. Draw cyclic pressure curve. Also non-fired

More information

Principles of Engine Operation. Information

Principles of Engine Operation. Information Internal Combustion Engines MAK 4070E Principles of Engine Operation Prof.Dr. Cem Soruşbay Istanbul Technical University Information Prof.Dr. Cem Soruşbay İ.T.Ü. Makina Fakültesi Motorlar ve Taşıtlar Laboratuvarı

More information

Combustion engines. Combustion

Combustion engines. Combustion Combustion engines Chemical energy in fuel converted to thermal energy by combustion or oxidation Heat engine converts chemical energy into mechanical energy Thermal energy raises temperature and pressure

More information

GASOLINE DIRECT INJECTION IN SI ENGINES B. PAVAN VISWANADH P. ASHOK KUMAR. Mobile No : Mobile No:

GASOLINE DIRECT INJECTION IN SI ENGINES B. PAVAN VISWANADH P. ASHOK KUMAR. Mobile No : Mobile No: GASOLINE DIRECT INJECTION IN SI ENGINES SUBMIT TED BY B. PAVAN VISWANADH P. ASHOK KUMAR Y06ME011, III/IV B. Tech Y06ME003, III/IV B. Tech Pavan.visu@gmail.com ashok.me003@gmail.com Mobile No :9291323516

More information

Handout Activity: HA185

Handout Activity: HA185 Cylinder heads Handout Activity: HA185 HA185-2 Cylinder head The cylinder head bolts onto the top of the cylinder block where it forms the top of the combustion chamber. It carries the valves and, in many

More information

Exhaust Gas CO vs A/F Ratio

Exhaust Gas CO vs A/F Ratio Title: Tuning an LPG Engine using 2-gas and 4-gas analyzers CO for Air/Fuel Ratio, and HC for Combustion Efficiency- Comparison to Lambda & Combustion Efficiency Number: 18 File:S:\Bridge_Analyzers\Customer_Service_Documentation\White_Papers\18_CO

More information

Ignition control. The ignition system tasks. How is the ignition coil charge time and the ignition setting regulated?

Ignition control. The ignition system tasks. How is the ignition coil charge time and the ignition setting regulated? 1 Ignition control The ignition system tasks To transform the system voltage (approximately 14 V) to a sufficiently high ignition voltage. In electronic systems this is normally above 30 kv (30 000 V).

More information

Performance and Emissions of the 1999 LS1 Engine. Edward Froehlich Eric Tribbett Lex Bayer Mechanical Engineering Department Stanford University

Performance and Emissions of the 1999 LS1 Engine. Edward Froehlich Eric Tribbett Lex Bayer Mechanical Engineering Department Stanford University Performance and Emissions of the 1999 LS1 Engine Edward Froehlich Eric Tribbett Lex Bayer Mechanical Engineering Department Stanford University 2 ABSTRACT In this study we examine the performance and emissions

More information

THE FOURTH STATE. Gaining a universal insight into the diagnosis of automotive ignition systems. By: Bernie Thompson

THE FOURTH STATE. Gaining a universal insight into the diagnosis of automotive ignition systems. By: Bernie Thompson THE FOURTH STATE Gaining a universal insight into the diagnosis of automotive ignition systems By: Bernie Thompson Did you know that the forth state of matter powers the spark ignition internal combustion

More information

Dual Fuel Engine Charge Motion & Combustion Study

Dual Fuel Engine Charge Motion & Combustion Study Dual Fuel Engine Charge Motion & Combustion Study STAR-Global-Conference March 06-08, 2017 Berlin Kamlesh Ghael, Prof. Dr. Sebastian Kaiser (IVG-RF), M. Sc. Felix Rosenthal (IFKM-KIT) Introduction: Operation

More information

Engine Exhaust Emissions

Engine Exhaust Emissions Engine Exhaust Emissions 1 Exhaust Emission Control Particulates (very challenging) Chamber symmetry and shape Injection characteristics (mixing rates) Oil control Catalyst (soluble fraction) Particulate

More information

CHAPTER 1 INTRODUCTION

CHAPTER 1 INTRODUCTION 1 CHAPTER 1 INTRODUCTION 1.1 GENERAL Diesel engines are the primary power source of vehicles used in heavy duty applications. The heavy duty engine includes buses, large trucks, and off-highway construction

More information

EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) H4DOTC

EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) H4DOTC EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) H4DOTC SYSTEM OVERVIEW 1. System Overview There are three emission control systems, which are as follows: Crankcase emission control system Exhaust emission

More information

This engine is certified to operate on regular 87 octane unleaded fuel (R+M)/2 Idle Speed (in gear): 650 RPM. Timing: Idle: 4-8 ATDC WOT:28 BTDC

This engine is certified to operate on regular 87 octane unleaded fuel (R+M)/2 Idle Speed (in gear): 650 RPM. Timing: Idle: 4-8 ATDC WOT:28 BTDC FUEL SYSTEMS 3 E Emission Control Information This engine conforms to 1998 Model Year U.S. EPA regulations for marine SI engines. Refer to Owners Manual for required maintenance. Exhaust Emission Control

More information

SpiritPFC Torque/Horsepower Comparison Dynamometer Test Date: 5/7/2006

SpiritPFC Torque/Horsepower Comparison Dynamometer Test Date: 5/7/2006 SpiritPFC / Comparison Dynamometer Test Date: 5/7/2006 Dynamometer Test Outline: Contained within this document you will find data collected using a Dyno Datamite engine dynamometer hardware and software

More information

UNIT 2 RCET, BHILAI. [Prof. Santosh Bopche & Prof. S. A. K. Jilani] 1

UNIT 2 RCET, BHILAI. [Prof. Santosh Bopche & Prof. S. A. K. Jilani] 1 UNIT 2 Fuels Basic requirement of I.C. Engine fuels, requirement of an ideal gasoline, structure of petroleum, effect of fuel structure on combustion, volatility of liquid fuels, effect of volatility on

More information

AT AUTOMOTIVE ENGINES QUESTION BANK

AT AUTOMOTIVE ENGINES QUESTION BANK AT6301 - AUTOMOTIVE ENGINES QUESTION BANK UNIT I: CONSTRUCTION & WORKING PRINCIPLE OF IC ENGINES 1. State the application of CI engines? 2. What is Cubic capacity of an engine? 3. What is the purpose of

More information

CEE 452/652. Week 6, Lecture 1 Mobile Sources. Dr. Dave DuBois Division of Atmospheric Sciences, Desert Research Institute

CEE 452/652. Week 6, Lecture 1 Mobile Sources. Dr. Dave DuBois Division of Atmospheric Sciences, Desert Research Institute CEE 452/652 Week 6, Lecture 1 Mobile Sources Dr. Dave DuBois Division of Atmospheric Sciences, Desert Research Institute Today s topics Read chapter 18 Review of urban atmospheric chemistry What are mobile

More information

Chapter 6. NOx Formation and Reduction in Reciprocating Internal Combustion Engines (RICE)

Chapter 6. NOx Formation and Reduction in Reciprocating Internal Combustion Engines (RICE) Chapter 6 NOx Formation and Reduction in Reciprocating Internal Combustion Engines (RICE) Editor s Note: Chapter 6 NOx Formation and Reduction in Reciprocating Internal Combustion Engines (RICE) was written

More information

Chapter 6 NOx Formation and Reduction in Reciprocating Internal Combustion Engines (RICE)

Chapter 6 NOx Formation and Reduction in Reciprocating Internal Combustion Engines (RICE) Chapter 6 NOx Formation and Reduction in Reciprocating Internal Combustion Engines (RICE) Editor s Note: Chapter 6 NOx Formation and Reduction in Reciprocating Internal Combustion Engines (RICE) includes

More information

Vacuum Readings for Tuning and Diagnosis

Vacuum Readings for Tuning and Diagnosis Vacuum Readings for Tuning and Diagnosis -Henry P. Olsen Once you learn to properly interpret its readings, a vacuum gauge can be one of the most useful tools in your toolbox. 22 FEATURE Some people consider

More information

4. With a neat sketch explain in detail about the different types of fuel injection system used in SI engines. (May 2016)

4. With a neat sketch explain in detail about the different types of fuel injection system used in SI engines. (May 2016) SYED AMMAL ENGINEERING COLLEGE (Approved by the AICTE, New Delhi, Govt. of Tamilnadu and Affiliated to Anna University, Chennai) Established in 1998 - An ISO 9001:2000 Certified Institution Dr. E.M.Abdullah

More information

Comparative Study Of Four Stroke Diesel And Petrol Engine.

Comparative Study Of Four Stroke Diesel And Petrol Engine. Comparative Study Of Four Stroke Diesel And Petrol Engine. Aim: To study the construction and working of 4- stroke petrol / diesel engine. Theory: A machine or device which derives heat from the combustion

More information

State of the Art (SOTA) Manual for Internal Combustion Engines

State of the Art (SOTA) Manual for Internal Combustion Engines State of the Art (SOTA) Manual for Internal Combustion Engines July 1997 State of New Jersey Department of Environmental Protection Air Quality Permitting Program State of the Art (SOTA) Manual for Internal

More information

Recent enhancement to SI-ICE combustion models: Application to stratified combustion under large EGR rate and lean burn

Recent enhancement to SI-ICE combustion models: Application to stratified combustion under large EGR rate and lean burn Recent enhancement to SI-ICE combustion models: Application to stratified combustion under large EGR rate and lean burn G. Desoutter, A. Desportes, J. Hira, D. Abouri, K.Oberhumer, M. Zellat* TOPICS Introduction

More information

Sensors & Controls. Everything you wanted to know about gas engine ignition technology but were too afraid to ask.

Sensors & Controls. Everything you wanted to know about gas engine ignition technology but were too afraid to ask. Everything you wanted to know about gas engine ignition technology but were too afraid to ask. Contents 1. Introducing Electronic Ignition 2. Inductive Ignition 3. Capacitor Discharge Ignition 4. CDI vs

More information

UNDERSTANDING 5 GAS DIAGNOSIS

UNDERSTANDING 5 GAS DIAGNOSIS UNDERSTANDING 5 GAS DIAGNOSIS AND EMISSIONS Gas Diagnostic Steps This procedure will help in your efforts to figure out what the five-gas reading are telling you. In order for five gas analyses to be conclusive

More information

SAMPLE STUDY MATERIAL

SAMPLE STUDY MATERIAL IC Engine - ME GATE, IES, PSU 1 SAMPLE STUDY MATERIAL Mechanical Engineering ME Postal Correspondence Course Internal Combustion Engine GATE, IES & PSUs IC Engine - ME GATE, IES, PSU 2 C O N T E N T 1.

More information

EFFECTS OF INTAKE AIR TEMPERATURE ON HOMOGENOUS CHARGE COMPRESSION IGNITION COMBUSTION AND EMISSIONS WITH GASOLINE AND n-heptane

EFFECTS OF INTAKE AIR TEMPERATURE ON HOMOGENOUS CHARGE COMPRESSION IGNITION COMBUSTION AND EMISSIONS WITH GASOLINE AND n-heptane THERMAL SCIENCE: Year 2015, Vol. 19, No. 6, pp. 1897-1906 1897 EFFECTS OF INTAKE AIR TEMPERATURE ON HOMOGENOUS CHARGE COMPRESSION IGNITION COMBUSTION AND EMISSIONS WITH GASOLINE AND n-heptane by Jianyong

More information

Port Fuel Injection (PFI) Strategies for Lean Burn in Small Capacity Spark Ignition Engines

Port Fuel Injection (PFI) Strategies for Lean Burn in Small Capacity Spark Ignition Engines ISSN 2395-1621 Port Fuel Injection (PFI) Strategies for Lean Burn in Small Capacity Spark Ignition Engines #1 Shailendra Patil, #2 Santosh Trimbake 1 shailendrapatil7592@gmail.com 2 santoshtrimbake@yahoo.co.in

More information

Learning Guide EMISSION SPECIALIST 5 GAS ANALYSIS COURSE NUMBER: E001-01

Learning Guide EMISSION SPECIALIST 5 GAS ANALYSIS COURSE NUMBER: E001-01 Learning Guide EMISSION SPECIALIST 5 GAS ANALYSIS COURSE NUMBER: E001-01 Notice Due to the wide range of vehicles makes and models, the information given during the class will be general in nature and

More information

Combustion process Emission cleaning Fuel distribution Glow plugs Injectors Low and high pressure pumps

Combustion process Emission cleaning Fuel distribution Glow plugs Injectors Low and high pressure pumps Page 1 of 16 S60 (-09), 2004, D5244T, M56, L.H.D, YV1RS799242356771, 356771 22/1/2014 PRINT Combustion process Emission cleaning Fuel distribution Glow plugs Injectors Low and high pressure pumps Fuel

More information

MULTIPOINT SPARK IGNITION ENGINE OPERATING ON LEAN MIXTURE

MULTIPOINT SPARK IGNITION ENGINE OPERATING ON LEAN MIXTURE MULTIPOINT SPARK IGNITION ENGINE OPERATING ON LEAN MIXTURE Karol Cupiał, Arkadiusz Kociszewski, Arkadiusz Jamrozik Technical University of Częstochowa, Poland INTRODUCTION Experiment on multipoint spark

More information

Fire in the Hole. Choosing a set of racing spark. Racing Spark Plugs. By Larry Carley, Technical Editor

Fire in the Hole. Choosing a set of racing spark. Racing Spark Plugs. By Larry Carley, Technical Editor Fire in the Hole Racing By Larry Carley, Technical Editor lcarley@babcox.com Choosing a set of racing spark plugs for a particular application is not as easy as it sounds because the plugs have to be closely

More information

9. The signal check of Intake Air Temperature Sensor

9. The signal check of Intake Air Temperature Sensor 9. The signal check of Intake Air Temperature Sensor 1. Troubles 1. The signal line is short to ground (Abnormally low signal voltage : below 0.5 [volt]) Cause of trouble Counter action Engine state Signal

More information

2.61 Internal Combustion Engines Spring 2008

2.61 Internal Combustion Engines Spring 2008 MIT OpenCourseWare http://ocw.mit.edu 2.61 Internal Combustion Engines Spring 2008 For information about citing these materials or our Terms of Use, visit: http://ocw.mit.edu/terms. Engine Heat Transfer

More information

Effect of Tangential Grooves on Piston Crown Of D.I. Diesel Engine with Retarded Injection Timing

Effect of Tangential Grooves on Piston Crown Of D.I. Diesel Engine with Retarded Injection Timing International Journal of Engineering Research and Development e-issn: 2278-067X, p-issn : 2278-800X, www.ijerd.com Volume 5, Issue 10 (January 2013), PP. 01-06 Effect of Tangential Grooves on Piston Crown

More information

E - THEORY/OPERATION - TURBO

E - THEORY/OPERATION - TURBO E - THEORY/OPERATION - TURBO 1995 Volvo 850 1995 ENGINE PERFORMANCE Volvo - Theory & Operation 850 - Turbo INTRODUCTION This article covers basic description and operation of engine performance-related

More information

Template for the Storyboard stage

Template for the Storyboard stage Template for the Storyboard stage Animation can be done in JAVA 2-D. Mention what will be your animation medium: 2D or 3D Mention the software to be used for animation development: JAVA, Flash, Blender,

More information

CHAPTER 7 CYCLIC VARIATIONS

CHAPTER 7 CYCLIC VARIATIONS 114 CHAPTER 7 CYCLIC VARIATIONS 7.1 INTRODUCTION In an apparently steady running spark ignition engine, there will be as much as 70% variation in peak pressures at certain operating condition (Winsor 1973).

More information

CHAPTER-5 USE OF HYDROGEN AS FUEL IN C.I ENGINE

CHAPTER-5 USE OF HYDROGEN AS FUEL IN C.I ENGINE 124 CHAPTER-5 USE OF HYDROGEN AS FUEL IN C.I ENGINE In this chapter use of hydrogen as fuel in I.C. engine is discussed on the basis of literature survey. Prospects of use of hydrogen in C.I. engine have

More information

Chapter 6. Supercharging

Chapter 6. Supercharging SHROFF S. R. ROTARY INSTITUTE OF CHEMICAL TECHNOLOGY (SRICT) DEPARTMENT OF MECHANICAL ENGINEERING. Chapter 6. Supercharging Subject: Internal Combustion Engine 1 Outline Chapter 6. Supercharging 6.1 Need

More information