Annex to the Accreditation Certificate D PL according to DIN EN ISO/IEC 17025:2005

Transcription

1 Deutsche Akkreditierungsstelle GmbH Annex to the Accreditation Certificate D PL according to DIN EN ISO/IEC 17025:2005 Period of validity: until Holder of certificate: TÜV Rheinland LGA Bautechnik GmbH Prüfstelle Baustoffe und Beton, Verkehrswegebau, Werkstoffe Tillystraße 2, Nürnberg Tests in the fields: Testing of concrete and grout, cement, admixtures and additives for concrete and grout, selected aggregates for concrete and grout, floor screed, building bricks, aerated and lightweight concrete, concrete goods, artificial stone, drainage goods, insulating materials, ceilings, wooden building components, material and construction element testing Tests of mineral construction materials and natural stone Geotechnical ground and soil investigations, sampling and testing of soils, rock and aggregate samples Testing of bituminous materials, road marking materials, coatings as well as hot and cold plastic masses non destructive testing of road surfaces and road areas mechanical structural test methods, tests of reinforcing steel, dynamic materials and components testing, testing of weld seams of metallic materials, metallographic and corrosion testing Test methods (investigation area I and special test methods of investigation area II) by third party testing authorities for the installation of mineral construction materials in landfill liner systems according to the Landfill Ordinance DepV and Federal Uniform Quality Standard BQS 9 1 Testing of construction products and testing of fire resistance within the framework of EU Regulation No. 305/2011 laying down the harmonised conditions for the marketing of construction products (Construction Products Regulation CPR) Abbreviations used: see last page This document is a translation. The definitive version is the original German annex to the accreditation certificate. 1/52

2 The testing laboratory is permitted, without being required to inform and obtain prior approval from DAkkS, to use standard testing methods listed here with different issue dates. This is valid for all areas of accreditation scope with the exception of section 4 (CPR). 1 Tests of concrete adhesives, concrete, grout, floor screed, building bricks and masonry, admixtures and additives, mineral building products and natural stones 1.1 Binders and concrete DIN EN DIN EN DIN EN DIN EN DIN EN Methods of testing cement Part 1: Determination of strength Method of testing cement Part 2: Chemical analysis of cement Methods of testing cement Part 3: Determination of setting times and soundness Methods of testing cement Part 6: Determination of fineness Methods of testing cement Part 7: Methods of taking and preparing samples of cement The above listed standards are to be used in connection with the following guidance documents: DIN EN DIN EN DIN EN Cement Part 1: Composition, specifications and conformity criteria for common cements Cement Part 2: Conformity evaluation Cement Part 1: Composition, specifications and conformity criteria for common cements DIN EN DIN EN Method of testing fly ash Part 2: Determination of fineness by wet sieving Methods of test for mortar for masonry Part 3: Determination of consistence of fresh mortar (by flow table) Period of validity: to Translation 2/52

3 DIN EN Binders, composite binders and factory made mixtures for floor screeds based on calcium sulfate Part 2: Test methods in connection with: DIN EN Binders, composite binders and factory made mixtures for floor screeds based on calcium sulfate Part 1: Definitions and requirements DIN EN DIN EN DIN DIN EN DIN EN DIN EN DIN EN DIN EN Masonry cement Part 2: Test methods Gypsum plasterboards Definitions, requirements and test methods Trass Requirements, Tests Admixtures for concrete, mortar and grout Test methods Part 1: Reference concrete and reference mortar for testing Admixtures for concrete, mortar and grout Test methods Part 2: Determination of setting time Admixtures for concrete, mortar and grout Test methods Part 4: Determination of bleeding of concrete Admixtures for concrete, mortar and grout Test methods Part 11: Determination of air void characteristics in hardened concrete Admixtures for concrete, mortar and grout Part 6: Sampling, conformity control and evaluation of conformity The above listed standards are to be used in connection with the following guidance documents: DIN EN Chemicals used for treatment of water intended for human consumption High calcium lime DIN EN Grout for prestressing tendons Test methods Period of validity: to Translation 3/52

4 DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN DIN EN Testing fresh concrete Part 1: Sampling Testing fresh concrete Part 2: Slump test Testing fresh concrete Part 3: Vebe test Testing fresh concrete Part 4: Degree of compactibility Testing fresh concrete Part 5: Flow table test Testing fresh concrete Part 6: Density Testing fresh concrete Part 7: Air content Pressure methods Testing fresh concrete Part 8: Self compacting concrete Slumpflow test Testing fresh concrete Part 11: Self compacting concrete Sieve segregation test Testing fresh concrete Part 12: Self compacting concrete J ring test Testing concrete in structures Part 1: Cored specimens Taking, examining and testing in compression Testing concrete in structures Part 2: Non destructive testing Determination of rebound number Testing concrete testing of hardened concrete (specimens prepared in mould) Testing hardened concrete Part 1: Shape, dimensions and other requirements for specimens and moulds Period of validity: to Translation 4/52

5 DIN EN Corrigenda DIN EN Corrigenda DIN EN DIN EN DIN EN DIN EN ZTV Ing, Teil Testing hardened concrete Part 2: Making and curing specimens for strength tests Testing hardened concrete Part 3: Compressive strength of test specimens (withdrawn standard) Testing hardened concrete Part 5: Flexural strength of test specimens Testing hardened concrete Part 6: Tensile splitting strength of test specimens Testing hardened concrete Part 7: Density of hardened concrete Testing hardened concrete Part 8: Depth of penetration of water under pressure Additional terms of contract and guidelines for structural Engineering general part 3 tests during construction part 3.3 The above listed standards are to be used in connection with the following guidance documents: ZTV Ing, Teil DAfStB RiLi Schutz und Instandsetzung von Betonbauteilen Additional terms of contract and guidelines for structural Engineering solid structure part 4 protection and maintenance of concrete building parts annex B determination of concrete humidity with the CM device DAfStB guideline for protection and maintenance of concrete building parts part 3: requirements for service companies and surveillance of execution DAfStb RiLi Wassergefährdende Stoffe DAfStb Heft DAfStb guideline for concrete structural engineering using water polluting substances annex A: test method (only test method A2) Testing of concrete advice and hints as in addition to DIN 1048, only chapters 2.2, 2.5, 2.6 und 3.3 Period of validity: to Translation 5/52

6 The above listed standards are to be used in connection with the following guidance document: DAStb Richtline Steel fibre concrete DIN DIN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN Testing concrete testing of hardened concrete (specimens taken in situ) Test methods for concrete determination of the compressive strength in hardened concrete in structures and components application of reference lines and evaluation with special methods Assessment of in situ compressive strength in structures and precast concrete components Testing sprayed concrete Part 1: Sampling fresh and hardened concrete Testing sprayed concrete Part 3: Flexural strengths (first peak, ultimate and residual) of fibre reinforced beam specimens Testing sprayed concrete Part 4: Bond strength of cores by direct tension Testing sprayed concrete Part 6: Thickness of concrete on a substrate Testing sprayed concrete Part 7: Fibre content of fibre reinforced concrete Test methods for fibres in concrete Part 1: Reference concretes Test methods for fibres in concrete Part 2: Effect on concrete The above listed standards are to be used in connection with the following guidance documents: DIN EN DIN EN Fibres for concrete Part 1: Steel fibres Definitions, specifications and conformity Fibres for concrete Part 2: Polymer fibres Definitions, specifications and conformity Period of validity: to Translation 6/52

7 DIN Hard aggregates for cement bound floor screeds Requirements and test methods Other applicable documents: ONR ÖNORM B Test methods for concrete National application of testing standards for concrete and its source materials Repair, reconstruction and strengthening of concrete structures 1.2 Grout DIN DIN EN Testing of magnesium oxychloride screeds Adhesives for tiles Determination of slip The above listed standards are to be used in connection with the following guidance document: DIN EN Adhesives for tiles Concrete slabs for tests DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN Adhesives for tiles Determination of shear adhesion strength of dispersion adhesives Adhesives for tiles Determination of open time Adhesives for tiles Determination of wetting capability Adhesives for tiles Determination of tensile adhesion strength for cementitious adhesives Methods of test for mortar for masonry Part 1: Determination of particle size distribution (by sieve analysis) Methods of test for mortar for masonry Part 2: Bulk sampling of mortars and preparation of test mortars Period of validity: to Translation 7/52

8 DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN Methods of test for mortar for masonry Part 3: Determination of consistence of fresh mortar (by flow table) Methods of test for mortar for masonry Part 4: Determination of consistence of fresh mortar (by plunger penetration) Methods of test for mortar for masonry Part 6: Determination of bulk density of fresh mortar Methods of test for mortar for masonry Part 7: Determination of air content of fresh mortar Methods of test for mortar for masonry Part 9: Determination of workable life and correction time of fresh mortar Methods of test for mortar for masonry Part 10: Determination of dry bulk density of hardened mortar Methods of test for mortar for masonry part 11: determination of flexural and compressive strength of hardened mortar Methods of test for mortar for masonry Part 12: Determination of adhesive strength of hardened rendering and plastering mortars on substrates Methods of test for mortar for masonry Part 18: Determination of water absorption coefficient due to capillary action of hardened mortar Methods of test for mortar for masonry Part 19: Determination of water vapour permeability of hardened rendering and plastering mortars Adhesives for tiles Determination of transverse deformation for cementitious adhesives and grouts Adhesive for tiles Determination of shear adhesion strength of reaction resin adhesives The above listed standards are to be used in connection with the following guidance documents: DIN EN Adhesives for tiles Requirements, evaluation of conformity, classification and designation Period of validity: to Translation 8/52

9 DIN EN Adhesives for tiles Requirements, evaluation of conformity, classification and designation DIN DIN DIN DIN DIN DIN DIN DIN DIN DIN Testing of mortars containing mineral binders general, sampling, test mortar (withdrawn standard) Testing of mortars containing mineral binders freshly mixed mortars containing aggregates of dense structure (heavy aggregates) determination of consistence, bulk density and air content (withdrawn standard) Testing of mortars containing mineral binders hardened mortars determination of flexural strength, compressive strength and bulk density Testing of mortars containing mineral binders hardened mortars determination of linear and transverse strain and of deformation characteristics of masonry mortars by the static pressure test Testing of mortars containing mineral binders hardened mortars determination of bond shear strength of masonry mortars (withdrawn standard) Testing of mortars containing mineral binders determination of bond strength of hardened mortar Testing of mortars containing mineral binders determination of water retentivity of freshly mixed mortar by the filter plate method Testing of mortars containing mineral binders freshly mixed mortar determination of workability time and correction time of thinbed mortar for use with masonry (withdrawn standard) Testing of mortars containing mineral binders Part 9: Hardened mortars determination of the mortar compressive strength in the bed joint Testing of coating material for synthetic resin plasters and of synthetic resin plasters (withdrawn standard) Period of validity: to Translation 9/52

10 1.3 Screeds DIN EN DIN EN DIN EN DIN EN Methods of test for screed materials Part 1: Sampling, making and curing specimens for test Methods of test for screed materials Part 2: Determination of flexural and compressive strength Methods of test for screed materials Part 3: Determination of wear resistance Böhme Methods of test for screed materials Part 8: Determination of bond strength The above listed standards are to be used in connection with the following guidance documents: DIN EN DIN DIN DIN DIN DIN Screed material and floor screeds Screed materials Properties and requirements Floor screeds in building construction Part 1: General requirements, testing and construction Floor screeds in building construction Part 2: Floor screeds and heating floor screeds on insulation layers Floor screeds in building construction Part 3: Base bonded floor screeds Floor screeds Part 4: Screeds laid on separated layer Floor screeds Part 7: Heavy duty screeds (industrial screeds) 1.4 Building bricks and masonry DIN EN DIN EN Methods of tests for ancillary components for masonry Part 2: Determination of bond strength of prefabricated bed joint reinforcement in mortar joints Methods of tests for ancillary components for masonry Part 3: Determination of shear load capacity of welds in prefabricated bed joint reinforcement Period of validity: to Translation 10/52

11 DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN Methods of test for ancillary components for masonry Part 4: Determination of load capacity and load deflection characteristics of straps Methods of test for ancillary components for masonry Part 5: Determination of tensile and compressive load capacity and load displacement characteristics of wall ties (couplet test) Methods of test for ancillary components for masonry Part 6: Determination of tensile and compressive load capacity and load displacement characteristics of wall ties (single end test) Methods of test for ancillary components for masonry Part 7: Determination of shear load capacity and load displacement characteristics of shear ties and slip ties (couplet test for mortar joint connections) Methods of tests for ancillary components for masonry Part 8: Determination of load capacity and load deflection characteristics of joist hangers Methods of tests for ancillary components for masonry Part 9: Determination of flexural resistance and shear resistance of lintels Methods of test for ancillary components for masonry Part 10: Determination of load capacity and load deflection characteristics of brackets Methods of test for ancillary components for masonry Part 11: Determination of dimensions and bow of lintels Methods of test for ancillary components for masonry Part 13: Determination of resistance to impact, abrasion and corrosion of organic coatings Methods of test for masonry units Part 1: Determination of compressive strength Methods of test for masonry units Part 6: Determination of bending tensile strength of aggregate concrete masonry units Methods of test for masonry units Part 14: Determination of moisture movement of aggregate concrete and manufactured stone masonry units Period of validity: to Translation 11/52

12 DIN EN Methods of test for masonry units Part 15: Determination of water vapour permeability of autoclaved aerated concrete masonry units The above listed standards are to be used in connection with the following guidance documents: DIN EN DIN EN DIN EN DIN V DIN V DIN V DIN Specification for ancillary components for masonry Part 1: Wall ties, tension straps, hangers and brackets Specification for ancillary components for masonry Part 2: Lintels Specification for ancillary components for masonry Part 3: Bed joint reinforcement of steel meshwork Lightweight concrete hollow blocks Part 100: Hollow blocks with specific properties Lightweight concrete solid bricks and blocks Part 100: Solid bricks and blocks with specific properties Concrete masonry units (Normal weight concrete) Part 100: Masonry units with specific properties Clay masonry units Part 100: Clay masonry units with specific properties 1.5 Aerated and lightweight concrete DIN EN DIN EN DIN EN DIN EN Determination of the dry density of autoclaved aerated concrete Determination of the compressive strength of autoclaved aerated concrete Determination of the drying shrinkage of autoclaved aerated concrete Test methods for verification of corrosion protection of reinforcement in autoclaved aerated concrete and lightweight aggregate concrete with open structure Period of validity: to Translation 12/52

13 DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN Determination of the dimensions of prefabricated reinforced components made of autoclaved aerated concrete or lightweight aggregate concrete with open structure Determination of the dry density of lightweight aggregate concrete with open structure Determination of flexural strength of autoclaved aerated concrete Determination of static modulus of elasticity under compression of autoclaved aerated concrete or lightweight aggregate concrete with open structure Determination of moisture content of autoclaved aerated concrete Determination of compressive strength of lightweight aggregate concrete with open structure The above listed standards are to be used in connection with the following guidance documents: DIN V DIN Autoclaved aerated concrete masonry units Part 100: High precision units and elements with specific properties Autoclaved aerated concrete slabs and panels 1.6 physical performance of construction products DIN EN ISO DIN EN ISO DIN EN Hygrothermal performance of building materials and products Determination of hygroscopic sorption properties Hygrothermal performance of building materials and products Determination of water vapour transmission properties Thermal performance of building materials and products Determination of thermal resistance by means of guarded hot plate and heat flow meter methods Products of high and medium thermal resistance Period of validity: to Translation 13/52

14 1.7 Roof panels, insulating materials, wooden structures, planked ceiling and suspended ceilings DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN Fibre cement slates and fittings Product specification and test methods, except 7.3.3, und 7.5 Fibre cement profiled sheets and fittings Product specification and test methods, only and Thermal insulating products for building applications Determination of length and width Thermal insulating products for building applications Determination of thickness Thermal insulating products for building applications Determination of squareness Thermal insulating products for building applications Determination of flatness Thermal insulating products for building applications Determination of compression behaviour (here: without determination of 10% compression) Thermal insulating products for building applications Determination of the apparent density Thermal insulating products for building applications Determination of tensile strength perpendicular to faces Thermal insulating products for building applications Determination of tensile strength parallel to faces Thermal insulating products for building applications Determination of short term water absorption by partial immersion Thermal insulating products for building applications Determination of water vapour transmission properties Thermal insulating products for building applications Determination of water vapour transmission properties Period of validity: to Translation 14/52

15 DIN EN DIN DIN DIN EN DIN EN DIN EN DIN EN DIN EN DIN Thermal insulating products for building applications Determination of bending behaviour Filler concrete joists for reinforced and prestressed concrete floors Design of timber structures Part 10: Additional provisions Timber structures Test methods Withdrawel capacity of timber fasteners Timber structures Test methods Pull through resistance of timber fasteners Timber structures Dowel type fasteners Requirements Metal framing components for gypsum board systems Definitions, requirements and test methods Thermal insulation products for buildings In situ thermal insulation formed from expanded perlite (EP) products Part 1: Specification for bonded and loose fill products before installation Ceiling linings and suspended ceilings with gypsum plasterboards Part 2: Verification of the load carrying capacity of metal subconstructions and metal suspending rods in connection with : DIN Ceiling linings and suspended ceilings with gypsum plasterboards Part 1: Requirements for construction DIN EN ETAG Suspended ceilings Requirements and test methods Guideline for european technical approval of internal partition kits for use as non loadbearing walls Period of validity: to Translation 15/52

16 1.8 Cast stones DIN V Cast stones Terminology, requirements, testing, inspection in connection with : DIN Concrete kerb units Shapes, dimensions, marking DIN EN Corrigenda E DIN EN Bundesverband Deutsche Beton und Fertigteilindustrie e.v., Bonn DIN EN Corrigenda E DIN EN DIN EN Corrigenda E DIN EN DIN EN DIN EN Concrete paving blocks Requirements and test methods, not annex G Concrete paving blocks Requirements and test methods, not annex G Guideline, production and quality assurance of permeable concrete paving blocks made of open matrix concrete Concrete paving flags Requirements and test methods, not annex G Concrete paving flags Requirements and test methods, not annex G Concrete kerb units Requirements and test methods, not annex G Concrete kerb units Requirements and test methods, not annex G Terrazzo tiles Part 1: Terrazzo tiles for internal use, not section Terrazzo tiles Part 2: Terrazzo tiles for external use, not section Period of validity: to Translation 16/52

17 The above listed standards are to be used in connection with the following guidance document: BGB RINGB Non standardized concrete products Requirements and test methods DIN DIN Corrigenda DIN EN DIN EN DIN EN Step irons for single line installation Step irons for setting in concrete Step irons for single line installation Step irons for setting in concrete Steps for underground man entry chambers Requirements, marking, testing and evaluation of conformity Drainage channels for vehicular and pedestrian areas Classification, design and testing requirements, marking and evaluation of conformity Gully tops and manhole tops for vehicular and pedestrian areas design requirements, testing, marking, quality control 1.9 Mineral construction materials DIN EN Test for general properties of aggregates Part 1: Methods for sampling in connection with : ZTV wwg StB By 05 Az: IID / Additional technical Conditions for contract and delivery for required water management relevant quality parameter for the use of recycled road construction products in Bavaria, only section 6.1 DIN EN DIN EN Test for general properties of aggregates Part 2: Methods for reducing laboratory samples Tests for general properties of aggregates Part 3: Procedure and terminology for simplified petrographic description Period of validity: to Translation 17/52

18 The above listed standards are to be used in connection with the following guidance document: DIN EN Tests for general properties of aggregates Part 5: Common equipment and calibration DIN EN ÖNORM EN ÖNORM EN ÖNORM EN DIN EN DIN EN DIN EN DIN EN DIN EN Tests for geometrical properties of aggregates Part 1: Determination of particle size distribution Sieving method Tests for geometrical properties of aggregates Part 1: Determination of particle size distribution Sieving method Unbound and hydraulically bound mixtures Part 41: Test method for the determination of the compressive strength of hydraulically bound mixtures Unbound and hydraulically bound mixtures Part 42: Test method for the determination of the indirect tensile strength of hydraulically bound mixtures Tests for geometrical properties of aggregates Part 3: Determination of particle shape Flakiness index Tests for geometrical properties of aggregates Part 4: Determination of particle shape Shape index Tests for geometrical properties of aggregates Part 5: Determination of percentage of crushed and broken surfaces in coarse aggregate particles Tests for geometrical properties of aggregates Part 6: Assessment of surface characteristics Flow coefficient of aggregates Tests for geometrical properties of aggregates Part 7: Determination of shell content percentage of shells in coarse aggregates Period of validity: to Translation 18/52

19 DIN EN DIN EN DIN EN DIN EN DIN DIN EN DIN EN DIN EN DIN EN DIN EN Corrigenda DIN EN Tests for geometrical properties of aggregates Part 8: Assessment of fines Sand equivalent test Tests for geometrical properties of aggregates Part 9: Assessment of fines Methylene blue test Tests for geometrical properties of aggregates Part 10: Assessment of fines Grading of filler aggregates (air jet sieving) Tests for geometrical properties of aggregates Part 11: Classification test for the constituents of coarse recycled aggregate Testing of aggregates Test methods for the assessment of the weathering resistance Tests for mechanical and physical properties of aggregates Part 1: Determination of the resistance to wear (micro Deval) Tests for mechanical and physical properties of aggregates Part 2: Methods for the determination of resistance to fragmentation Tests for mechanical and physical properties of aggregates Part 3: Determination of loose bulk density and voids Tests for mechanical and physical properties of aggregates Part 4: Determination of the voids of dry compacted filler Tests for mechanical and physical properties of aggregates Part 7: Determination of the particle density of filler Pyknometer method Tests for mechanical and physical properties of aggregates Part 8: Determination of the polished stone value Period of validity: to Translation 19/52

20 DIN EN DIN EN Corrigenda DIN EN DIN EN DIN EN Corrigenda E DIN EN DIN EN DIN DIN EN Tests for thermal and weathering properties of aggregates Part 1: Determination of resistance to freezing and thawing Tests for thermal and weathering properties of aggregates Part 3: Boiling test for "Sonnenbrand basalt Tests for thermal and weathering properties of aggregates Part 5: Determination of resistance to thermal shock Tests for thermal and weathering properties of aggregates Part 6: Determination of resistance to freezing and thawing in the presence of salt (NaCl) Lightweight aggregates for concrete, mortar, grout, bituminous mixtures, surface treatments and for unbound and bound applications, not annex B Lightweight aggregates for concrete, mortar, grout, bituminous mixtures, surface treatments and for unbound and bound applications, not annex B Lightweight aggregates Part 2: Lightweight aggregates for bituminous mixtures and surface treatments and for unbound and bound applications Test methods for aggregates Part 2: Impact test on crushed and broken aggregates larger than 32 mm Tests for chemical properties of aggregates Part 1: Chemical analysis, only chapter und 15.1 DIN EN DIN EN DIN EN Unbound and hydraulically bound mixtures Part 2: Test methods for laboratory reference density and water content Proctor compaction Armourstone Part 1: Specification Aggregates for railway ballast, only annexes A, C and D Period of validity: to Translation 20/52

21 DIN EN TP Beton StB 10 Teil TP Gestein StB Teil TP Gestein StB Teil TP Gestein StB Teil TP Gestein StB Teil TP Gestein StB Teil TP Gestein StB Teil TP Gestein StB Teil TP Gestein StB Teil TP Gestein StB Teil Tests for filler aggregate used in bituminous mixtures Part 1: Delta ring and ball test TP concrete StB 10 Technical test specifications for load bearing strata with hydraulic Binders and concrete road surfaces, part 3.1 TP aggregates StB: Technische test specification for aggregates for road construction material labelling of household waste incinerator ash (municipal incinerator bottom ash aggregates) Material labelling of recycled construction materials Determination of grain size distribution of fine grain sizes (air jet sieving) Determination of grain size distribution of Filler (air jet sieving) Estimation of ratio rounded to fragmented parts in fine grain sizes using a Binocular Impact test on particle size distributions > 32 mm Los Angeles test method on particle size distributions > 32 mm Determination of polished stone value (PSV fgk ) Determination of hardness Dynamic CBR test Period of validity: to Translation 21/52

22 TP Gestein StB Teil TP Gestein StB Teil TP Gestein StB Teil TP Gestein StB Teil TP Gestein StB Teil DIN EN TP Asphalt StB Teil Resistance of mineral grain size composition against freeze thaw cycles Resistance of fine aggregates against frost and thaw changes Resistance of coarse aggregates against heat exposure Resistance of fine aggregates against heat exposure Water sensitivity of fine aggregates shaking and abrasive method Bituminous mixtures Test methods for hot mix asphalt Part 11: Determination of the affinity between aggregate and bitumen Technical test directives for Asphalt Part 11: adhesion betweenstone and Bitumen 1.10 Natural stone and brick DIN EN DIN EN DIN DIN EN DIN EN Natural stone test method Determination of real density and apparent density, and of total and open porosity Natural stone test methods Determination of water absorption at atmospheric pressure Natural stone test methods Assessment of the weathering resistance, only annexes C and D Natural stone test methods Determination of uniaxial compressive strength Natural stone test methods Determination of flexural strength under concentrated load Period of validity: to Translation 22/52

23 DIN EN DIN EN DIN EN DIN DIN DIN EN DIN EN DIN EN DIN EN Natural stone test methods Determination of flexural strength under constant moment Natural stone test methods Determination of the breaking load at dowel hole Natural stone test methods Determination of the abrasion resistance Testing of floor coverings determination of the anti slip properties wet loaded barefoot areas walking method ramp test Testing of floor coverings Determination of the anti slip property Workrooms and fields of activities with slip danger Walking method Ramp test Clay roofing tiles for discontinuous laying Flexural strength test Clay roofing tiles for discontinuous laying Determination of physical characteristics Part 1: Impermeability test Clay roofing tiles for discontinuous laying Determination of physical characteristics Part 2: Test for frost resistance Clay roofing tiles for discontinuous laying Determination of geometric characteristics Period of validity: to Translation 23/52

24 2 Geotechnical site investigation, sampling and testing of soil, rocks and aggregate samples 2.1 Sampling DIN EN ISO DIN EN ISO DIN EN ISO DIN EN ISO DIN DIN 19672, Blatt DIN Geotechnical investigation and testing Identification and classification of soil Part 1: Identification and description Geotechnical investigation and testing Identification and classification of soil Part 2: Principles for a classification Geotechnical investigation and testing Identification and classification of rock Part 1: Identification and description Geotechnical investigation and testing Sampling methods and groundwater measurements Part 1: Technical principles for execution Geotechnical investigation and testing Graphical presentation of logs of boreholes, trial pits, shafts and adits Apparatus for drawing soil samples in agricultural engineering apparatus for soil sampling in undisturbed situation Aggregates test methods Sampling 2.2 soil and ground physical investigation DIN EN ISO FGSV Nr. 591/B DIN Geotechnical investigation and testing Field testing Part 2: Dynamic probing TP BF StB Technical test guidelines for soil and rock in road construction part B 15.1 Light dynamic probing DPL 5 und middle heavy dynamic probing DPM 10 Construction site tests in situ Part 4: vane shear test Period of validity: to Translation 24/52

25 TP BF StB Teil B DIN DIN DIN DIN DIN DGGT Empfehlung Nr DGGT Empfehlung Nr DGGT Empfehlung Nr DGGT Empfehlung Nr DGGT Empfehlung Nr DGGT Empfehlung Nr DGGT Empfehlung Nr Dynamic plate load test using a Drop Weight Tester Sports grounds Part 4: Sports turf areas Soil, investigation and testing Determination of density of solid particles Capillary pycnometer, wide mouth pycnometer, gas pycnometer Soil, investigation and testing Determination of density of noncohesive soils for maximum and minimum compactness Soil, investigation and testing Determination of the coefficient of water permeability Part 2: Field tests Soil, investigation and testing Determination of shear strenght Part 1: Concepts and general testing conditions Uniaxiale load tests on rock samples Triaxiale load tests on rock samples Point load tests on rock samples Indirect tensile test on rock samples tension fatigue test Swelling pressure test on rock samples Multistep technic for triaxial load tests and direct tensile tests Uni and triaxial creep tests on rock samples Period of validity: to Translation 25/52

26 QMA Swelling pressure tests in connection with : DGGT Empfehlung Nr Swelling pressure test on rock samples DIN EN Tests for general properties of aggregates Part 3: Procedure and terminology for simplified petrographic description 2.3 Test methods (investigation area I) by third party testing authorities for the installation of mineral construction materials in landfill liner systems according to the Landfill Ordinance DepV and Federal Uniform Quality Standard BQS 9 1 DIN DIN DIN DIN DIN DIN / * DIN / * DIN / * Soil, investigation and testing Water content Part 1: Determination by drying in oven Soil, investigation and testing Water content Part 2: Determination by rapid methods Soil, investigation and testing Consistency limits Part 1: Determination of liquid limit and plastic limit Soil, investigation and testing Determination of grain size distribution Soil, investigation and testing Determination of density of soil Part 1: Laboratory tests Soil investigation and testing Determination of density of soil Part 2: Field tests (Edition replaced) Soil, investigation and testing Proctor test (Edition replaced) Soil Investigation and testing Determination of ignition loss (Edition replaced) DIN / / * Soil, investigation and testing Determination of lime content (Edition und replaced) Period of validity: to Translation 26/52

27 DIN DIN / * DIN * DIN DIN / / * GDA E 3 12 (Nr. 3.6):2011 GDA Empfehlungen 3. Auflage 1997 S.268 Überarbeitung 4/2011 Soil investigation and testing Determination of the coefficient of water permeability Part 1: Laboratory tests Soil, testing procedures and testing equipment Determination of water absorption (Edition replaced) Soil Testing procedures and testing equipment Plate load test (Edition and replaced) Soil quality Field tests Part 1: Determination of soil colour Soil quality Field tests Part 2: Determination of soil texture (Edition und replaced) Acceptance test of mineral drainage layers para. 3.6 total carbonate content 2.4 Test methods (Investigation area II) by third party testing authorities for the installation mineral construction materials in landfill liner systems according to the Landfill Ordinance DepV and Federal Uniform Quality Standard BQS 9 1 DIN EN DIN EN DIN EN Corrigenda DIN EN / DIN EN DIN Test for general properties of aggregates Part 1: Methods for sampling Test for general properties of aggregates Part 2: Methods for reducing laboratory samples Tests for mechanical and physical properties of aggregates Part 5: Determination of the water content by drying in a ventilated oven Tests for mechanical and physical properties of aggregates Part 6: Determination of particle density and water absorption (Edition replaced) Tests for thermal and weathering properties of aggregates Part 1: Determination of resistance to freezing and thawing Soil investigation and testing Part 2: Determination of the shrinkage limit Period of validity: to Translation 27/52

28 DIN / DIN DIN / * DIN DIN / Investigation and testing Oedometer consolidation test (Edition replaced) Soil Investigation and testing Unconfined compression test Soil, investigation and testing Determination of shear strength Part 2: Triaxial test (Edition replaced) Soil, investigation and testing Determination of shear strength Part 3: Direct shear test Construction site tests in situ part 2: Standard Penetration Test (Edition replaced) Other applicable documents (for Investigation areas I and II) DIN EN DIN / * Aggregates for concrete Earthworks and foundation soil classification for civil engineering purposes (Edition replaced) *Previous editions already replaced new versions, but still remain as basis of BQS 2.5 Testing of bituminous construction materials DIN EN TP Asphalt StB Teil Bituminous mixtures Test methods for hot mix asphalt Part 20: Indentation using cube or cylindrical specimens Technical testing of asphalt Part 20: Intrusion depth on cubic samples DIN EN TP Asphalt StB Teil Bituminous mixtures Test methods for hot mix asphalt Part 27: sampling Technical guidelines for bituminous mixtures Part 27: sampling Period of validity: to Translation 28/52

29 DIN EN TP Asphalt StB Teil DIN EN TP Asphalt StB Teil DIN EN TP Asphalt StB Teil DIN EN TP Asphalt StB Teil DIN EN TP Asphalt StB Teil DIN EN TP Asphalt StB Teil DIN EN TP Asphalt StB Teil DIN EN Bituminous mixtures Test methods for hot mix asphalt Part 28: Preparation of samples for determining binder content, water content and grading Technical test guidelines for bituminous mixtures Part 28: Preparation of samples Bituminous mixtures Test methods for hot mix asphalt Part 30: Specimen preparation by impact compactor Technical test guidelines for bituminous mixtures Part 30: making of test specimens with the impact compactor (MVG) Bituminous mixtures Test methods for hot mix asphalt Part 1: Soluble binder content Technical test guidelines for bituminous mixtures Part 1: Soluble binder content Bituminous mixtures Test methods for hot mix asphalt Part 3: Bitumen recovery: Rotary evaporator Technical test guidelines for bituminous mixtures Part 3: Bitumen recovery: Rotary evaporator Technical test guidelines for bituminous mixtures Part 5: Determination of the maximum density Technical test guidelines for bituminous mixtures Part 5: Determination of the maximum density Bituminous mixtures Test methods for hot mix asphalt Part 6: Determination of bulk density of bituminous specimens Technical test guidelines for bituminous mixtures Part 6: Determination of bulk density of bituminous specimens Bituminous mixtures Test methods for hot mix asphalt Part 8: Determination of the air voids content of bituminous specimen Technical test guidelines for bituminous mixtures Part 8: Determination of the air voids content of bituminous specimen and degree of compaction Bituminous mixtures Test method for hot mix asphalt Part 2: Determination of particle size distribution Period of validity: to Translation 29/52

30 TP Asphalt StB Teil DIN EN TP Asphalt StB Teil DIN EN TP Asphalt StB Teil DIN EN TP Asphalt StB Teil DIN EN TP Asphalt StB Teil TP Asphalt StB Teil ÖNORM B ÖNORM B ÖNORM EN DIN EN DIN EN Technical test guidelines for bituminous mixtures Part 2: Determination of particle size distribution Bituminous mixtures Test methods for hot mix asphalt Part 35: Laboratory mixing Technical test guidelines for bituminous mixtures Part 35: Laboratory mixing Bituminous mixtures Test methods for hot mix asphalt Part 13: Temperature measurement Technical test guidelines for bituminous mixtures Part 13: Temperature measurement Bituminous mixtures Test methods for hot mix asphalt Part 18: Binder drainage Technical test guidelines for bituminous mixtures Part 18: Drain of stone mastic asphalt and porous asphalt Bituminous mixtures Test method for hot mix asphalt Part 29: Determination of the dimensions of bituminous specimen Technical test guidelines for bituminous mixtures Part 29: Determination of dimensions of bituminous specimen Technical test guidelines for bituminous mixtures Part 80: Shear test Asphalts for road construction and related purposes Testing Shear resistance in contact surfaces of asphalt layers Asphalts for road construction and related purposes Testing Pull off resistance in contact surfaces of asphalt layers Bituminous mixtures Test methods for hot mix asphalt Part 36: Determination of the thickness of a bituminous pavement Bitumen and bituminous binders Characterisation of perceptible properties Bitumen and bituminous binders Determination of needle penetration Period of validity: to Translation 30/52

31 E DIN EN DIN EN E DIN EN DIN EN DIN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN Multiple tress Creep and Recovery Test AL MSCR Prüfung (DSR) 2012 Bitumen and bituminous binders Determination of needle penetration Bitumen and bituminous binders Determination of the softening point Ring and Ball method Bitumen and bituminous binders Determination of the softening point Ring and Ball method Bitumen and bituminous binders Determination of the elastic recovery of modified bitumen Bitumen and bituminous binders Determination of ductility Bitumen and bituminous binders Preparation of test samples Bitumen and bituminous binders Preparation of test samples Bitumen and bituminous binders Determination of the resistance to hardening under the influence of heat and air Part 1: RTFOT method Bitumen and bituminous binders Accelerated long term ageing conditioning by a Pressure Ageing Vessel (PAV) Bitumen and bituminous binders Determination of complex shear modulus and phase angle using a Dynamic Shear Rheometer (DSR) Bitumen and bituminous binders Determination of the flexural creep stiffness Bending Beam Rheometer (BBR) Guideline fort the determination of deformation of Bitumen and bituminous binders using a Dynamic Shear Rheometer (DSR) execution of MSCR test 2.6 Testing of road marking materials DIN EN Road marking materials Laboratory methods for identification Period of validity: to Translation 31/52

32 DIN EN DIN EN DIN EN ZTV M 02 Teil ZTV M 02 Teil ZTV M 02 Teil ZTV M 02 Teil ZTV M 02 Teil ZTV M 02 Teil ZTV M 02 Teil Road marking materials Road marking performance for road users Road marking materials Drop on materials Glass beads, antiskid aggregates and mixtures of the two Road marking materials Premix glass beads Testing of height overhang, milling depth, milling width and milling length Examination of the amount supernatant Testing of drop on materials Testing of trafficability (drying time) Testing of day visibility Testing of night visibility Testing of skid resistance Testing of wear resistance (life time) 2.7 Testing of road equipment DIN EN EN DIN EN EN Lighting columns Part 3 1: Design and verification Specification for characteristic loads Lighting columns Part 3 1: Design and verification Specification for characteristic loads Lighting columns Part 3 2: Design and verification Verification by testing Lighting columns Part 3 2: Design and verification Verification by testing Period of validity: to Translation 32/52