Natural gas engine E 0836 LE 202 Technical data

Transcription

1 Page 1 Principle: No of cylinders : Supercharging: Mixture cooling: Engine cooling : Lubrication : Spark plugs: Starter motor: 4-stroke Otto gas engine 6 in line Exhaust turbocharger with water-cooled turbine housing, pressure-lubricated bearings and water-cooled bearing pedestal Two-stage mixture cooling with high and low temperature cycle. Without mixture water pump the coolant circulation must be designed with external cooling water pumps with mixture temperature regulation at 50 C or 80 C Without engine water pump, coolant to be circulated by external water pump with temperature control. Pressure lubrication by gear-driven pump, exchangeable lube-oil filter in full flow and lube oil cooler integrated in engine coolant circuit. Special spark plug for industrial gas engines Pre-engaged-drive starter 24 V kw Starter battery capacity: 143 Ah, 24 V

2 Page 2 Mixture cooling up to 50 C 80 C Engine data 50 Hz 50 Hz Rated speed rpm ISO standard rating kw Air ratio λ Configuration in-line engine in-line engine No of cylinders 6 6 Bore mm Stroke mm Swept volume l Direction of rotation looking on flywheel left left Flywheel housing SAE 2 SAE 2 Ring gear with number of teeth Z Compression ratio ε Mean effective pressure bar Mean piston speed m/s Lube oil consumption kg/h Lube oil filling quantity min./max. l 24/34 24/34 Coolant filling quantity l max. operating pressure bar 2 2 min. engine coolant circulation quantity l/min Coolant temperature min. C max. coolant temperature C Difference (inlet - outlet max.) K 6 6 Max. mixture inlet temperature after throttle valve C Max. mixture cooling water inlet temperature LT C Min. mixture cooling water circulation quantity LT l/min Pressure loss LT mbar Max. mixture cooling water inlet temperature HT C Min. mixture cooling water circulation quantity HT l/min Pressure loss HT mbar max. suction pressure mbar max. exhaust back pressure mbar Engine width mm Engine length mm Engine height mm Engine weight, dry kg Lube oil to MAN works standard M 3271 and coolant to MAN works standard M 324 N/NF/SNF Gas quality to MAN data sheet - minimum requirement for the gas quality for MAN gas engines Air ratio measured by lambdameter ETAS LA 4_E

3 Page 3 Mixture cooling up to 50 C Rating data 50 Hz Load % Moment of ignition before BTDC grad ISO standard rating kw Coolant heat kw Mixture heat HT kw Mixture heat LT kw Exhaust-gas heat up to 120 C kw Radiation heat max. kw 12 Energy input kw Fuel consumption MJ/kWh Efficiency mechanical % thermal % total % Mass flows Combustion air kg/h Fuel kg/h Exhaust gas mass flow rate, wet kg/h Temperatures Exhaust gas temperature C Emission values NO X mg/nm³ < 500 at 5 % residual oxygene CO mg/nm³ < 650 at 5 % residual oxygene HCHO (Formaldehyd) mg/nm³ < 60 at 5 % residual oxygene NMHC mg/nm³ < 150 at 5 % residual oxygene Engine surface noise db ( A ) 98.6 Exhaust sound pressure level db ( A ) Reverence gas mixing unit: RMG 985 a-100/50 and ignition system Woodward IC 100 The technical data are based on natural gas with a calorific value of 10 kwh/nm³ and a methane no. > 80 The ISO standard rating indicated is based on standard conditions acc to DIN ISO Standard conditions: Atmospheric pressure absolute: 100 kpa Air temperature 25 C Relative air humidity 30 % Rating adaptation at ambient conditions acc to DIN ISO The tolerance for the specific fuel consumption is + 5 % at rated output The tolerance for the usable heat is 7 % at rated output The coolant data are based on a 40 % portion of antifreeze

4 Page 4 Mixture cooling up to 80 C Rating data 50 Hz Load % Moment of ignition before BTDC grad ISO standard rating kw Coolant heat kw Mixture heat HT + LT kw Exhaust-gas heat up to 120 C kw Radiation heat max. kw 14 Energy input kw Fuel consumption MJ/kWh Efficiency mechanical % thermal % total % Mass flows Combustion air kg/h Fuel kg/h Exhaust gas mass flow rate, wet kg/h Temperatures Exhaust gas temperature C Emission values NO X mg/nm³ < 500 at 5 % residual oxygene CO mg/nm³ < 650 at 5 % residual oxygene HCHO (Formaldehyd) mg/nm³ < 60 at 5 % residual oxygene NMHC mg/nm³ < 150 at 5 % residual oxygene Engine surface noise db ( A ) 98.6 Exhaust sound pressure level db ( A ) Reverence gas mixing unit: RMG 985 a-100/50 and ignition system Woodward IC 100 The technical data are based on natural gas with a calorific value of 10 kwh/nm³ and a methane no. > 80 The ISO standard rating indicated is based on standard conditions acc to DIN ISO Standard conditions: Atmospheric pressure absolute: 100 kpa Air temperature 25 C Relative air humidity 30 % Rating adaptation at ambient conditions acc to DIN ISO The tolerance for the specific fuel consumption is + 5 % at rated output The tolerance for the usable heat is 7 % at rated output The coolant data are based on a 40 % portion of antifreeze

5 Page 5 Mixture cooling up to 50 C Engine data 60 Hz Rated speed rpm 1800 ISO standard rating kw 110 Air ratio λ 1.6 Configuration in-line engine No of cylinders 6 Bore mm 108 Stroke mm 125 Swept volume l 6.87 Direction of rotation looking on flywheel left Flywheel housing SAE 2 Ring gear with number of teeth Z 143 Compression ratio ε 11 Mean effective pressure bar Mean piston speed m/s 7.5 Lube oil consumption kg/h 0.03 Lube oil filling quantity min./max. l 24/34 Coolant filling quantity l 16 max. operating pressure bar 2 min. engine coolant circulation quantity l/min 240 Coolant temperature min. C 80 max. coolant temperature C 88 Difference (inlet - outlet max.) K 6 Max. mixture inlet temperature after throttle valve C 50 Max. mixture cooling water inlet temperature LT C 40 Min. mixture cooling water circulation quantity LT l/min 32 Pressure loss LT mbar 500 Max. mixture cooling water inlet temperature HT C 85 Min. mixture cooling water circulation quantity HT l/min 43 Pressure loss HT mbar 700 max. suction pressure mbar 15 max. exhaust back pressure mbar 40 Engine width mm 740 Engine length mm 1300 Engine height mm 1030 Engine weight, dry kg 605 Lube oil to MAN works standard M 3271 and coolant to MAN works standard M 324 N/NF/SNF Gas quality to MAN data sheet - minimum requirement for the gas quality for MAN gas engines Air ratio measured by lambdameter ETAS LA 4_E

6 Page 6 Mixture cooling up to 50 C Rating data 60 Hz Load % Moment of ignition before BTDC grad ISO standard rating kw Coolant heat kw Mixture heat HT kw Mixture heat LT kw Exhaust-gas heat up to 120 C kw Radiation heat max. kw 14 Energy input kw Fuel consumption MJ/kWh Efficiency mechanical % thermal % total % Mass flows Combustion air kg/h Fuel kg/h Exhaust gas mass flow rate, wet kg/h Temperatures Exhaust gas temperature C Emission values NO X mg/nm³ < 500 at 5 % residual oxygene CO mg/nm³ < 600 at 5 % residual oxygene HCHO (Formaldehyd) mg/nm³ < 60 at 5 % residual oxygene NMHC mg/nm³ < 150 at 5 % residual oxygene Engine surface noise db ( A ) Exhaust sound pressure level db ( A ) Reverence gas mixing unit: RMG 985 a-100/50 and ignition system Woodward IC 100 The technical data are based on natural gas with a calorific value of 10 kwh/nm³ and a methane no. > 80 The ISO standard rating indicated is based on standard conditions acc to DIN ISO Standard conditions: Atmospheric pressure absolute: 100 kpa Air temperature 25 C Relative air humidity 30 % Rating adaptation at ambient conditions acc to DIN ISO The tolerance for the specific fuel consumption is + 5 % at rated output The tolerance for the usable heat is 7 % at rated output The coolant data are based on a 40 % portion of antifreeze

7 Resistance curve of engine Page 7 2,1 2 1,9 1,8 1,7 1,6 1,5 1,4 1,3 Pressure loss (bar) 1,2 1,1 1 0,9 0,8 0,7 0,6 0,5 0,4 0,3 0,2 0, Volume flow (l/min)

8 Resistance curve of HT mixture cooling Page 8 1,8 1,7 1,6 1,5 1,4 1,3 1,2 1,1 Pressure loss (bar) 1 0,9 0,8 0,7 0,6 0,5 0,4 0,3 0,2 0, Volume flow (l/min)

9 Resistance curve of LT mixture cooling Page 9 1,8 1,7 1,6 1,5 1,4 1,3 1,2 1,1 Pressure loss (bar) 1 0,9 0,8 0,7 0,6 0,5 0,4 0,3 0,2 0, Volume flow (l/min)