P-62M / P-62L PNEUMATIC SUPPORT LEG

Transcription

1 P-62M / P-62L PNEUMATIC SUPPORT LEG Pneumatic support leg P-62M / P-62L is used to increase performance and improve the comfort of working with a WUP-22 drilling machine. The support is intended to support the drilling machine during operation and to exert uniform pressure on the drill. The articulated connection of the pneumatic support to the WUP-22 drilling machine makes it possible to drill lateral and inclined holes. The support is equipped with a regulation valve which makes it possible to smoothly adjust the pressure force and the slide out speed, providing a firm working grip at the same time. The support is equipped with a quick release valve for reasons of work safety. The purpose of this valve is to withdraw the mining device immediately, interrupting the drill pressure. Parameters Unit TYPE P-62M TYPE P-62L Weight kg 20,5 24,5 Total length mm Stroke mm Upstream air pressure MPa 0,4 0,6 0,4 0,6 Operating factor Compressed air Force of pressure at 0,4MPa kn 12,8 12,8

2 WUP-22 PNEUMATIC PERCUSSIVE DRILLING MACHINE The WUP-22 pneumatic percussive drilling machine is designed for drilling blast holes in medium hard coal and rocks at air pressure of 0,4 MPa. Bore dust removal can be affected by flushing or scavening. To increase speed of penetration in horizontal or inclined drilling WUP-22 is adopted to work with an airleg of P-62M. The purpose of the airleg is supporting the drill during operation providing uniform pressure and relieving arduousness of men work. Pneumatic drilling machines WUP-22 require lubrication by compressed air from e.g. a duct lubricator. For WUP-22 we may apply the tools for hammer drilling: (monolithic) or rods and bits. Weight (without drill bit) kg 22 Number of strokes* min Drill revolutions* min Air consumption* m 3 /min 3,2 Energy of blow* J 28 Feeding hose diameter mm Ø25 Flushing pipe inner diameter mm Ø12,5 Drill retainer size mm 22,2(7/8 )x108 or 25,5(1 )x108 * The values obtained of 0,4 MPa compressed air pressure. Power pressure 0,3 0,4 MPa. ATEX I M2

3 PWR-5U PWR-8T PNEUMATIC HAND ROTARY DRILLING MACHINE Pneumatic hand rotary drilling machine PWR-5U is designed for boring holes up to 62 mm in diameter. Can be used in the construction industry and tunnels drilling. Its high power permits drilling of blast-holes in salt beds, ore- -body and other soft and mean-hard rocks. The drilling machine is supplied with compressed air via lubricator. Tools applied for drilling: spiral drilling rod or rhombus spiral drilling rod as well as drill bit. Drill can not be usedin underground mines. Weight kg 14 Rated torque Mo Nm 42 Rated power N kw 2,2 Number of drill revolution n min Upstream pressure p MPa 0,4 Maximal upstream pressure pmax MPa 0,5 Air consumption Q m 3 /min 2,7 Inner diameter of hose Ø mm 16 Maximal tool diameter Ø mm 62 Pneumatic hand rotary drilling machine PWR-8T (with noise suppresser) is designed for drilling holes of diameter up to 43 mm in soft and semi-hard rock. It is successfully used for drilling holes in the salt beds. The drilling machine is supplied with compressed air via lubricator. Tools applied for drilling: spiral drilling rod or rhombus spiral drilling rod as well as drill bit. Drill can not be used in underground mines. Weight kg 9,5 Rated torque Mo Nm 19,5 Rated power N kw 1,6 Number of drill revolution n min Upstream pressure p MPa 0,4 Maximal upstream pressure pmax MPa 0,5 Air consumption Q m 3 /min 2,4 Inner diameter of hose Ø mm 16 Maximal tool diameter Ø mm 43

4 PZW-1 PNEUMATIC DRILL KIT Pneumatic Drill Kit PDK-1 is used for drilling holes in semi-hard and hard rocks at different angles, with the air pressure MPa. Pneumatic drill kit PDK-1 allows you to remove cuttings from the hole with water or compressed air. Included with the device is upgraded WUP-22 drill, which is mounted on the pneumatic prop. Prop is used to support drilling and exert steady pressure on the drill bit during drilling, thereby reducing the effort of the employee. Kit weight PZW-1 kg ca. 40 Length (without drill bit) mm ca. 635 Driller weight (without drill bit) kg ca. 24 Stroke frequency (at 0,4 MPa pressure) 1/min 1950 Drill rotation speed (at 0,4 MPa pressure) rpm 200 Impact energy J 28 Compressed air pressure max. (high timing gear) MPa 0,6 Compressed air pressure max. (low timing gear) MPa 0,4 Air consumption (at 0,4 MPa pressure) m 3 /min 3,2 Internal diameter of the compressed air hose mm Ø25 Internal diameter of water hose mm Ø12,5 Dimension of drill grip mm 22,2(7/8 )x108 or 25,4(1 )x108 Prop length mm according to customer orders Useful change of the prop in range mm ATEX I M2

5 WGH-4 HYDRAULIC MINING DRILL Hydraulic Mining Drill WGH 4 is designed mainly for manual rotary drilling of openings in rocks of medium hardness with use of tools consisting of spiral drilling rod ended by drilling bit. It is characterized by low weight using two-handed grip. Maximum drilling diameter Ø48 mm. Drill WGH-4 can be use directly while performing work in underground mining and other places where methane hazard categories are b and c and B grade coal dust explosion hazard. Driller weight kg 5 Maximal rotary torque Mo Nm 72 Work pressure P bar Maximal rotational speed n max rpm 957 motor absorption Q l/min 25 przy 500 rpm Maximal work temperature (front body) C 75,3 Type of medium used Hydraulic oil HLP 48 or water-oil emulsion Drill without gear. Weight ratio to rotational torque Drills can be adapted to the needs of the customer in mass, momentum, pressure, power, and used medium.

6 WGH-6u HYDRAULIC MINING DRILL Hydraulic Mining Drill WGH-6u is designed mainly for manual rotary drilling of openings in hard rocks and overgrowth rock of varying hardness with use of tools consisting of spiral drilling rod ended by appropriate tool. Drill has a mechanical stroke-assistant driller supporting the work, so that it becomes less cumbersome. Maximum drilling diameter Ø48 mm. Drill WGH - 6u can be use directly while performing work in underground mining and other places where methane hazard categories are b and c and B grade coal dust explosion hazard. Driller weight kg 8 Maximal rotary torque Mo Nm 150 Work pressure P bar Maximal rotational speed n max rpm 820 Motor absorption Q cm 3 /rpm 50 Maximal work temperature (front body) C 90 Type of medium used Hydraulic oil HLP 48 or water-oil emulsion Drill without gear. Weight ratio to rotational torque Drills can be adapted to the needs of the customer in mass, momentum, pressure, power, and used medium.

7 PWR II PNEUMATIC HAND ROTARY DRILLING MACHINE Mining Pneumatic hand rotary drilling machine PWR II is designed for boring blast-holes in coal, salt beds, ore-body and other soft and mean-hard rocks. The main advantage of drill PWR II is its use directly while performing work in underground mining where methane hazard categories are a, b and c and A and B grade coal dust explosion hazard. The drilling machine is supplied with compressed air via lubricator. Tools applied for drilling: spiral drilling rod or rhombus spiral drilling rod as well as drill bit. Maximum drilling diameter is Ø62 mm. Weight kg 19 Rotary torque Mo Nm 27 Rated power N kw 1,6 Number of drill revolutions n min Upstream air pressure p MPa 0,4 Maximal Upstream air pressure pmax MPa 0,5 Requisition of compressed air Q m 3 /min 2,7 Inner diameter of hose Ø mm 16 Maximum tool diameter Ø mm 62 ATEX I M2

8 S-3 LINE OIL LUBRICATOR The S-type line oil lubricator is intended for lubricating devices propelled by compressed air, such as drilling machines, pumps and supports with oil mist. Can be used in underground mines in hazard zones with the danger of methane and f coal dust explosion risk. The oil in the lubricator is atomised in the form of oil mist and reaches, together with the compressed air, all the surfaces that rub against each other during operation, preventing scuffing. Lubricating using an oil mist is one of the best methods of lubrication, helping lengthen the life of devices propelled by compressed air. The lubricator is placed on the tube supplying compressed air to the lubricated devices at a distance that does not exceed 5 m. The lubricator does not require additional maintenance, apart from filling with oil. Parameters Unit PCV steel Weight (without oil) kg ca. 2,5 ca. 4,0 Maximal pressure MPa 0,5 0,6 0,5 0,6 Capacity l 1 1 Oil consumption in temperature C ml/h ca. 100 ca. 100 Inner diameter of hose mm Ambient temperature C

9 ER-6 127V, 220V ELECTRIC HAND DRILLING MACHINE The ER-6 electric hand drilling machine is designed for drilling holes in solid coal and mean-hard rock using helical drill rod with drill bit in diameter of 43 mm. The driller has flameproof construction and can be used in underground mines in a, b or c hazard zones with the danger of methane explosion and at level A and B of coal dust explosion risk. Drill is manufactured in the following varieties: ER-6 ER-6 / 4, Voltage: ER-61 (3x127V) ER-62 (3x220V) and ER-61 / 4 (3x127V), ER-62 / 4 (3x220V), there is also a performance of the ER-6...U with supporting drilling hammer head. Parameters Unit ER-61 ER-62 ER-61/4 ER-62/4 ER-6...U Rated power kw 1,55 1,55 1,55 1,55 1,55 Motor rating kw 1,1 1,1 1,1 1,1 1,1 Power supply V ; 220 Frequency Hz Cos φ - 0,86 0,86 0,86 0,86 0,86 Rated current A 8,1 4,7 8,1 4,7 8,1 ; 4,7 Times the starting current Efficiency - 0,72 0,72 0,72 0,72 0,72 Insulation class - F F F F F Rotational speed rpm The torque on the drill Nm 17,5 17,5 26,6 26,6 17,5 Work - S2 30min S2 30min S2 30min S2 30min S2 30min Degree of cover protection - IP-54 IP-54 IP-54 IP-54 IP-54 Marking flameproof - Ex d I Ex d I Ex d I Ex d I Ex d I Weight without cable drill kg 15,5 15,5 16,5 16,5 19,2 Ambient temperature C The frequency of stroke Ud/min Allowed deviation values not exceeding + / - 5% of the nominal value.

10 SN 400 MOJ VALENT FRICTION PROP The VALENT SN 400 MOJ friction props are individual elements of lining whose is to prop the roof in mining excavations: longwall and splitting excavations, and to reinforce the lining of gallery excavations. Props may form an independent lining or be used as elements reinforcing another type of lining. The series of types of the VALENT SN-400- MOJ friction props include twenty two principal sizes ranging from 450mm to 4500mm when extended out. The VALENT SN-400- MOJ prop is certified and marked by safety sign. Length of the drop Lower prop pipe Upper prop pipe Height of the extended prop Height of the withdrawn prop Prop weight Strength of support Item [mm] [mm] [mm] [mm] [mm] [kg] [kn] , , , , , , , , , , , , , , , , , , , , , ,6 200

11 PKU 1 PNEUMATIC ROOF BOLTING MACHINE Pneumatic impact root bolting machine PKU-1 is designed for drilling shot and anchoring holes in the roof of medium-hard and hard rocks in excavations of height over 2600 mm at the pneumatic support stroke of 1300 mm as well as for tamping of anchor bolts. Upon the customer s request we may manufacture an anchoring machine with different cylinder stroke. The roof bolting machine PKU-1 has a possibility of adjusting the position of control valve depending on the excavation height. The adjustment is made by an operator of the anchoring machine at the workstation. Such a solution considerably reduces the noxiousness of work with the equipment. Maximum drilling diameter is 45 mm. Mass kg 45 Length without drilling rod (1) (2) Height with height with stretched prop (effective travel) (1) (2) mm mm mm mm Maximum supply pressure MPa 0,6 Minimum supply pressure MPa 0,4 Pessing force* kn 12,8 Impact energy* J 24,5 Stroke frequency* 1/min 1950 Tool speed* rpm 200 Air consumption m 3 /min 3,2 Internal diameter of the compressed air hose mm 25 Internal diameter of the water hose mm 12,5 Dimensions of drill shank mm 22,2(7/8 )x108 or 25,5(1 )x108 * The values obtained of 0,4 MPa compressed air pressure. It is possible to make pneumatic impact root bolting machine with a different ength as described above and the corresponding jump usefull. ATEX I M2

12 PKU-3 PNEUMATIC ROOF BOLTING MACHINE The PKU-3 compressed-air impact roof bolting machine is a multipurpose machine intended for drilling the blast holes in the roof and for drilling the bolt holes, for tamping and tightening the bolts in medium and hard rocks. Due to placing the drill at the side of the ram, a very compact design combined with a relatively high value of the active stroke has been obtained. The PKU-3 roof bolting machine has been designed especially for low underground workings and for faces where realization of the roof bolting is required directly after blasting, because it enables drilling to be effected from heaps of the gotten material. The minimum height of the working is determined by the length of the initial drill and amounts to 1400 mm. Mass kg 42 Height with maximal stretched prop mm 1740 Length mm 940 Cylinder stroke mm 750 Pessing force* kn 12,8 Impact energy* J 24,5 Stroke frequency* 1/min 1950 Drill bit rotation speed* 1/min 200 Air consumption * m 3 /min 3,2 Internal diameter of the compressed air hose mm 25 Internal diameter of the water hose mm 12,5 Dimensions of drill shank mm 22,2(7/8 )x108 or 25,5(1 )x108 * The values obtained of 0,4 MPa compressed air pressure. ATEX I M2

13 KHTP 1,5A HYDRAULIC ROOF BOLTING MACHINE Hydraulic roof bolting machine KHTP 1,5A is designed for rotary drilling with water flushing of holes in roofs of mining excavations of an angular and rectangular cross-section as well as mounting small diameter glued anchors therein. The roof bolting machine can be applied for anchoring dog headings and chamber excavations in rock of mean hardness and of compressive strength up to 60 MPa. The roof bolting machine should be fed with hydraulic oil HLP 68 by means of the power unit AG-63/16Z. Supply can be effected by other power unit meeting the requirements given in the technical specification of the anchoring machine. Hydraulic roof bolting machine KHTP 1,5A mass kg 80 Drill holding down force kn 4,0 10 Rated torque Nm 130 Maximal working pressure MPa 14,5 Maximal Instantaneous pressure* MPa 17,5 Maximal drill rotational speed* rpm 700 Rate of travel m/min 0 2 Drill stroke mm 1500 The maximum diameter of the drilling anchor Ø43 (recommended Ø 28) Maximum water pressure MPa 0,8 * Values obtained at a pressure of 0.4 MPa compressed air. ATEX I M2

14 AG 63/16Z HYDRAULIC AGGREGATE SET Hydraulic aggregate set AG 63/16Z is designed for supplying of equipment in underground excavations and may be used in underground mines in a, b or c hazard zones with the danger of methane explosion and at level A and B of coal dust explosion risk. In particular it is designed for supplying such equipment as hydraulic roof bolting machines, hydraulic drilling machines and other equipment with hydraulic drive. The version with a double-section pump (AG-16/63/40Z) allows for simultaneous operation of two different pieces of equipment (roof bolting machine and hydraulic drilling machine). It is possible to extend the application of aggregate to cooperation with other devices with hydraulic drive. Technical parameters Unit AG-63/16Z AG-63/16/40Z (for Dual-Pump) Motor power kw 15 or Nominal diameter of terminal mm 20 2X20 Max oil pressure MPa ,5 Nominal pump capacity l/min /40 Supply Engine voltage V Type of oil HL-48 or L-HL 68 Oil collection volume l < 200 Nominal diameter of runoff mm 25 Diameter of the cooling water connection ¾ Overall dimensions mm ca. 750 x 800 x 1800 Aggregate weight without oil kg ca. 550 Ambient temperature C Relative humidity 93% at temperature 40 O C±2 O C ATEX I M2

15 OP-80C DRAINAGE PUMP OP-80C pump is designed for pumping highly polluted water at a temperature till 40 C. It is a portable pump powered by compressed air directly immersed in liquid. In the case of total immersion pump outlet air pipe should be extended above the liquid mirror. In the mining is used to dewater the excavation, sewage, at work related to the sinking. Pump Weight: about 100 kg. Technical parameters of pump Designation Unit Air pressure MPa 0,4 0,5 Mass kg Efficiency Q l/min Lifting height H m water column Air consumption Vp Nm 3 /min 2,3 2,9 The efficiency of isothermal η i 0,24 0,21 Diameter Compressed air connection* mm 25,4 25,4 The internal diameter of discharge port mm Connection diameter structurally for the liquid - Pitch for bolts mm *The pump can be equipped with various types of terminals for compressed air connection 1 diameter. IM1c

16 KD-3, KD-4 TORQUE SPANNER Torque spanner KD-3/KD-4 is designed to turn tight bolts of lining on required moment. Wanted magnitude of moment is obtained through adequate regulation of spring tension handwheel located in end part of the spanner. Required magnitude of moments is read off on the scale located in gripped part of the spanner. The scale has measurement range of Nm. When checking screw home moment, exceed of moment is signaled by loud click of the pawl, located in central part of the spanner. The spanner is equipped with torque system to eliminate necessity of removing spanners cap from screw head. Type KD-3 KD-4 Weight (with torque and without thimb) 6,5 kg 6,5 kg Magnitude range of moment Nm Nm Size of head for thimbles kw. 25,4 mm (1 cal) kw. 25,4 mm (1 cal) Length 921 mm 921 mm KRW-1, KRP-1 HAND SPANNER BENDED / STRAIGHT Hand spanner bended KRW-1 and hand spanner straight KRP-1 are two-way action spanners with ratchet mechanism. They are served to tum off back off screw joints with the help of exchangeable thimbles: normal L = 110 mm and a short L = 75 mm. Thimbles can be ordered independently of a key or a set with him. Weight (without thimble) Moment of screwing Moment of screwin extending rod Size of joint for thimbles Length 1,5 kg 25 Nm 250 Nm kw. 25,4 mm (1 cal) 420 mm Standard thimbles: L = 110 mm Short thimbles: L = 75 mm S (M16) 24 (M18) 27 (M20) 30 (M22) 32 (M24) 36 (M27) 41 (M30) 46 (M33) 50 (M36) 55 S (M10) 16 (M12) 20 (M16) 24 (M20) 30 (M22) 32 (M24) 36 (M27) 41 (M30) 46 D D