Objectives Topics Resources & Notes GAIN ATTENTION Review homework from chapter 6 Slide 1 OBJECTIVE
|
|
- Curtis Ford
- 5 years ago
- Views:
Transcription
1 7 Outboard Engines and Stern Drives 67 COURSE LESSON TITLE PRESENTATION TIME PRESENTATION METHOD MATERIALS REQUIRED Chapter 7 Outboard Engines and Drives, and Stern Drives 2 hours Participative Lecture Ch7 PPT slides, computer, projector Objectives Topics Resources & Notes GAIN ATTENTION Review homework from chapter 6 Slide 1 OBJECTIVE PRESENTATION Outboard Systems Upon completion of this chapter, the student will have: 1. a good understanding of the component parts of the outboard marine engine and how these parts work together to propel the boat through the water 2. knowledge of the fuel, lubrication, cooling, exhaust, ignition and electrical systems needed for the outboard engine to function properly 3. an understanding of the stern drive that is used in inboard/outboard operation 1. Crankcase Similar to conventional crankcase, but designed to work vertically Different bearing design Dry sump lubrication 2. Crankshaft Bearings are designed for vertical operation Relies on mist lubrication 3. Pistons Long skirt to valve intake and exhaust ports No oil control grooves Domed head to scavenge cylinder gases 4. Carburetion Multiple carburetors are common Individual carburetors are simpler than inboard engine designs 5. Lubrication Oil mist lubrication o Usually requires oil and fuel to be premixed o Can be injected from oil reservoir No sump required No oil cooling benefit 6. Cooling and Exhaust Cooling derived from impeller pump in lower unit Most water cools the exhaust Exhaust is vented through the propeller hub Slide 2 Slides 3 4 Slide 5 Slide 6 Slide 7 Slide 8 Slide 9
2 68 7 Outboard Engines and Stern Drives Objectives Topics Resources & Notes 7. Ignition Magneto o Coil energy is provided by magnet in engine flywheel Distributor / breaker point o Same as inboard engines Solid state Slide 10 I/O Drive Systems 8. I/O Characteristics Slides Inboard engine Outboard drive system Generally pierces the transom, not the hull 9. Tilt and Trim Systems Slide 13 Mechanical on small drives Hydroelectric on larger systems 10. Routine Maintenance Service twice per season o Check lower unit lubricant and replace if necessary Replace zincs as needed (when >50% consumed) Check boots and seals for cracks Slide 14 Winter Storage Prevent freezing Slide 15 Check and replace lubricant as needed Replace zincs as needed (when >50% consumed) Warm the engine, then change the oil Run potable antifreeze through the raw water system Check boots and seals for cracks Paint housing if needed Spring Service Should not be necessary! Slide 16 EXERCISE SUMMARY HOMEWORK Complete homework questions for Chapter 7
3 7 Outboard Engines and Stern Drives 69 Homework Questions 1. The three major subassemblies of the outboard marine engine are the: a. power head, intermediate housing, and the drive housing. b. lower unit, drive housing, and the intermediate housing. c. power head, lower unit, and intermediate housing. d. lower unit, outer housing, and power head. 2. The subassembly of the outboard engine that provides a means for attaching the engine to the boat is the: a. lower unit. b. intermediate housing. c. power head. d. outer housing. 3. The subassembly of the outboard engine that operates under the water is the: a. power head. b. drive housing. c. intermediate housing. d. lower unit. 4. The subassembly of the outboard engine that usually contains the transmission for forward and reverse thrust as well as a neutral gear is the: a. power head. b. drive housing. c. intermediate housing. d. lower unit. 5. The two basic configurations for outboard engines are: a. 2-cycle and 4-cycle. b. saltwater and fresh water. c. portable and fixed mounted. d. propeller driven and jet driven. 6. The crankcase design for outboard engines differs from the inboard engine in that the outboard crankcase operates: a. with greater torque. b. in a vertical mode. c. without lubrication. d. without main bearings. 7. A 2-cycle outboard will generally have more per pound of weight than the four stroke outboard. a. parts. b. torque. c. compression. d. power. 8. A 2-cycle outboard engine: a. has exhaust valves in the power head. b. has exhaust ports in the cylinder walls. c. does not have piston rings. d. does not require lubrication.
4 70 7 Outboard Engines and Stern Drives 9. The purpose of the carburetor used with outboard engines is to: a. control carbon in the engine. b. provide correct fuel and air mixture. c. pump fuel from the fuel tank. d. provide timing to the engine. 10. Carburetors used on outboard engines are generally of the: a. single barrel design. b. two barrel design. c. four barrel design. d. multi-port design. 11. Fuel used in 2-cycle gasoline outboards must be mixed with: a. additives. b. alcohol. c. ethanol. d. oil. 12. The three basic ignition systems currently in use for outboard engines are: a. solid state, magneto, and permanent magnet. b. solid state, distributor/breaker point, and permanent magnet. c. solid state, magneto, and distributor/breaker point. d. distributor/breaker point, magneto, and permanent magnet. 13. Lubrication for 4-cycle outboard engines requires: a. oil to be mixed with the fuel. b. a separate oil reservoir. c. wet-sump operation. d. a simple oil pan reservoir. 14. In an outboard mechanical shifting transmission the engagement between the clutch and forward or reverse gear results in: a. positive and smooth load transfer. b. time lag between forward and reverse motion. c. slippage or power loss in the transmission. d. sudden shock and impact loads in the transmission. 15. A major difference between outboard engine drive systems and the inboard/outboard stern drive system is stern drives: a. are not attached to a boat s transom. b. have no reverse capability. c. are permanently attached through an opening in the transom. d. have no tilt capability. 16. The two factors that affect the trim of a boat powered by an outboard engine are the: a. horsepower of the engine and the diameter of the propeller. b. diameter of the propeller and the loading of the boat. c. horsepower of the engine and the tilt of the outboard motor. d. loading of the boat and the tilt of the outboard motor.
5 7 Outboard Engines and Stern Drives As a minimum, stern drives and the lower unit of outboard engines should be checked and serviced: a. only at the start of the boating season. b. twice during the boating season. c. only at the close of the boating season. d. once every 30 days. 18. Sacrificial zinc anodes should be replaced: a. if they are more than 50% consumed. b. only at the start of the boating season. c. when 75% consumed. d. only when laying-up the boat. 19. What steps should be taken if moisture or contaminants are found in the lubricant of the lower unit or stern drive? a. Find the cause, make repairs, and replace the lubricant. b. Flush the lower unit or stern drive and replace the lubricant. c. Add more lubricant to force the moisture or contaminants out. d. Drain and flush the lower unit or stern drive and add more lubricant.
6 72 7 Outboard Engines and Stern Drives
7 7 Outboard Engines and Stern Drives 73
8 74 7 Outboard Engines and Stern Drives
9 7 Outboard Engines and Stern Drives 75
10 76 7 Outboard Engines and Stern Drives
Objectives Topics Resources & Notes GAIN ATTENTION Review homework from Chapter 2 Slide 1 OBJECTIVE
3 Inboard Spark Engines - Part 2 29 COURSE LESSON TITLE Chapter 3 Inboard Spark Engines Part 2 PRESENTATION TIME PRESENTATION METHOD MATERIALS REQUIRED 2 hours Participative Lecture Ch3 PPT slides, computer,
More informationEM2007 Errata Student Manual 13 April 2008 Replace referenced paragraphs and homework questions with the following:
EM2007 Errata Student Manual 13 April 2008 Replace referenced paragraphs and homework questions with the following: Paragraph 7 Internal combustion engines convert about one third of the fuel s energy
More informationIMPORTANT INFORMATION
Table of Contents IMPORTANT INFORMATION Section 1B - Maintenance MAINTENANCE 1 B Specifications................................ 1B-1 Special Tools................................ 1B-2 Quicksilver Lubricant/Sealant..................
More informationMARINE.HONDA.COM.AU. BF10 (10hp Outboard)
MARINE.HONDA.COM.AU BF10 (10hp Outboard) Delivering dependable portable performance, the BF10 is ideal for inflatable boats, small aluminium dinghies and sailing boats. INTRODUCTION COMPACT AND POWERFUL
More informationEvinrude_Johnson HP Service Manual Outboard - PDF Service Manual
1973 1990 Evinrude_Johnson 48 235 HP Service Manual Outboard - PDF Service Manual DOWNLOAD HERE "1973 1990 Evinrude/Johnson 48 235 HP Service Manual Outboard - PDF Service Manual Johnson - Evinrude Service
More informationOutboard Engines This sneak preview of your study material has been prepared in advance of the book's actual online release.
Study Unit Outboard Engines This sneak preview of your study material has been prepared in advance of the book's actual online release. iii Preview An outboard engine is a special type of small engine
More informationEngine Construction and Principles of Operation
Ch. 4 Engine Construction and Principles of Operation Gasoline Engine A gasoline fueled engine is a mechanism designed to transform chemical energy into mechanical energy It is an internal combustion engine.
More informationMARINE.HONDA.COM.AU. BF20 (20hp Outboard)
MARINE.HONDA.COM.AU BF20 (20hp Outboard) The BF20 delivers unrivalled innovation to the portable range. It s a powerful, efficient and clean operator! INTRODUCTION RELIABILITY IN A COMPACT DESIGN With
More informationE50PL4SSC 4-Stroke, Elec Start, TNT, 20 IN. shaft 2000 : CAMSHAFT & TIMING [1/21] Page 1 of 44
E50PL4SSC 4-Stroke, Elec Start, TNT, 20 IN. shaft 2000 : CAMSHAFT & TIMING [1/21] Page 1 of 44 E50PL4SSC 4-Stroke, Elec Start, TNT, 20 IN. shaft 2000 : CAMSHAFT & TIMING [1/21] 1 5031326 1 CAMSHAFT, Intake
More informationMarine Service Technology
Marine Service Technology I. Demonstrate general shop practices. Each number to the right refers to a single student/candidate (1-10). Place a check ( ) in the respective column for the appropriate student/candidate
More informationE70PL4EEC 1999 : CAMSHAFT [1/23] Page 1 of 49
E70PL4EEC 1999 : CAMSHAFT [1/23] Page 1 of 49 E70PL4EEC 1999 : CAMSHAFT [1/23] 1 5030657 1 CAMSHAFT 2 5030658 1 PLATE, Camshaft thrust 3 5030549 1 SEAL, Camshaft 4 5030989 2 BOLT, Plate 5 5030663 8 ARM,
More informationCONTENTS 4 CYLINDER. ENGINE MECHANICAL GM V6 AND va ENGINES SPECIFICATIONS 4-41 ENGINE MECHANICAL. FORD va ENGINES SPECIFICATIONS 5-23 ENGINE OVERHAUL
CONTENTS HOW TO USE THIS MANUAL 1 2 BOATING SAFElY 1-4 SAFETY IN SERVICE 1 11 TROUBLESHOOTING 1 11 TOOLS AND EQUIPMENT 1-15 TOOLS 1-17 FASTENERS, MEASUREMENTS AND CONVERSIONS 1-24 1-25 ENGINE AND DRIVE
More informationUsing Multiple Cylinder Engines
Lesson A6 6 Using Multiple Cylinder Engines Unit A. Mechanical Systems and Technology Problem Area 6. Agricultural Power Systems Lesson 6. Using Multiple Cylinder Engines New Mexico Content Standard: Pathway
More informationJOB READY SAMPLE ASSESSMENT MARINE MECHANICS. Test Code: 1076 Version: 01
JOB READY SAMPLE ASSESSMENT MARINE MECHANICS Test Code: 1076 Version: 01 Specific Competencies and Skills Tested in this Assessment: Ignition System Disassemble ignition system (flywheel covering points/module)
More informationUnit C: Agricultural Power Systems. Lesson 6: Using Multiple Cylinder Engines
Unit C: Agricultural Power Systems Lesson 6: Using Multiple Cylinder Engines Student Learning Objectives: Instruction in this lesson should result in students achieving the following objectives: 1. Explain
More informationFundamentals of Small Gas Engines
Fundamentals of Small Gas Engines Objectives: Describe the four-stroke cycle engine operation and explain the purpose of each stroke Explain the concept of valve timing Describe two-stroke engine operation
More informationMERCURY DOWNLOAD Service Manual 90 to 300 HP Outboard - PDF Service Manual
MERCURY DOWNLOAD 1965 1989 Service Manual 90 to 300 HP Outboard - PDF Service Manual DOWNLOAD HERE "MERCURY DOWNLOAD 1965 1989 Service Manual 90 to 300 HP Outboard - PDF Service Manual MERCURY DOWNLOAD
More informationMARINE.HONDA.COM.AU. BF200 (200hp Outboard)
MARINE.HONDA.COM.AU BF200 (200hp Outboard) The BF200 delivers superior torque, top-end speed and world-class performance in a narrow, balanced V6 powerplant. INTRODUCTION MAXIMUM POWER Packed with power,
More informationMARINE.HONDA.COM.AU. BF250 (250hp Outboard)
MARINE.HONDA.COM.AU BF250 (250hp Outboard) The BF250 outboard engine takes Honda into the next power range. This flagship engine combines a new 3.6L, V6 EFI engine with the world s first direct air induction
More informationIMPORTANT INFORMATION
Table of Contents IMPORTANT INFORMATION Section 1B - Maintenance MAINTENANCE 1 B Specifications........................... 1B-1 Special Tools........................... 1B-2 Mercury/Quicksilver Lubricants
More informationBF2.3 MARINE.HONDA.COM.AU
BF2.3 MARINE.HONDA.COM.AU Reliable and quiet, the ergonomic carry handle of the lightweight BF2.3 allows the Honda experience to be enjoyed anywhere, anytime! INTRODUCTION PORTABLE POWER Not only does
More informationMARINE.HONDA.COM.AU. BF135 (135hp Outboard)
MARINE.HONDA.COM.AU BF135 (135hp Outboard) Delivering world-renowned quality and reliability through advanced engineering, the BF135 achieves unparalleled performance. INTRODUCTION CUTTING-EDGE ADVANTAGES
More informationImportant Information
Table of Contents Important Information Section 1C - Troubleshooting Troubleshooting 1 C Jetdrive Troubleshooting...1C-2 Jetdrive Unit Troubleshooting...1C-2 Performance Troubleshooting...1C-4 Hard Steering...1C-5
More informationTABLE OF CONTENTS 3 MAINTENANCE
TABLE OF CONTENTS 1 SAFETY " FUEL 1-1 CLEANING, WAXING, &: POLISHING 1-1 CONTROLLING CORROSION 1-1 PROPELLERS 1-2 FUEL SYSTEM 1-7 LOADING 1-9 HORSEPOWER 1-10 FLOTATION 1-10 EMERGENCYEQUWMENT 1-12 COMPASS
More information5/29/2014 3MSHY 2000 / CYLINDER CRANKCASE Yamaha Motor Corporation, U.S.A. All rights reserved.
Page 1 of 22 3MSHY 2000 / CYLINDER CRANKCASE Page 2 of 22 Part List 3MSHY 2000 / CYLINDER CRANKCASE REF - NO PART NUMBER PART NAME QUANTITY REMARKS 1 6L5-W0090-01-1S CRANK CYLINDER ASSY 1 2 6L5-15100-00-1S
More information5/29/2014 3MSHU 1996 / CYLINDER CRANKCASE Yamaha Motor Corporation, U.S.A. All rights reserved.
Page 1 of 22 3MSHU 1996 / CYLINDER CRANKCASE Page 2 of 22 Part List 3MSHU 1996 / CYLINDER CRANKCASE REF - NO PART NUMBER PART NAME QUANTITY REMARKS 1 6L5-W0090-01-4D CRANK CYLINDER ASSEMBLY 1 2 6L5-15100-00-94
More informationservice bulletin MCM 7.4L Bravo, MIE 7.4L Inboard GM Generation V Engine Specifications No. 91-6
service bulletin TO: SERVICE MANAGER MECHANICS PARTS MANAGER No. 91-6 MCM 7.4L Bravo, MIE 7.4L Inboard GM Generation V Engine Specifications NOTE: Generation V Engines Have the Fuel Pump Mounted on the
More informationParsun Portable 4-Stroke Outboard Motor Winterize or Storing DIY Service Guide
Parsun Portable 4-Stroke Outboard Motor Winterize or Storing DIY Service Guide To help keep your engine in tip-top condition for years to come, it is important that you winterize your outboard for off-season
More informationPOLARIS MARINE 1200 Model #W000099D Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN /00
POLARIS MARINE 00 Model #W000099D 000 Polaris Sales Inc. PARTS MANUAL PN 9968 and MICROFICHE PN 9969 /00 TABLE OF CONTENTS POLARIS MARINE 00 W000099D Parts Manual A AIR VENT...........................
More informationD9 & D9G Crawler S/n 66A1 to 66A3265
Caterpillar Service Manual D9 & D9G Crawler S/n 66A to 66A65 Service Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF CATERPILLAR OR IT S SUCCESSORS. CATERPILLAR AND IT S
More information9/7/2014 F9.9MSHV 1997 / CYLINDER CRANKCASE Yamaha Motor Corporation, U.S.A. All rights reserved.
F9.9MSHV 997 Page of 45 9/7/04 F9.9MSHV 997 / CYLINDER CRANKCASE 04 Yamaha Motor Corporation, U.S.A. All rights reserved. F9.9MSHV 997 Page of 45 9/7/04 Part List F9.9MSHV 997 / CYLINDER CRANKCASE REF
More informationTABLE OF CONTENTS "-11 "S" IN APPENDIX 1 SAFETY " FUEL
TABLE OF CONTENTS 1 SAFETY " FUEL 1-1 CLEANING, WAXING, & POLISHING 1-1 CONTROLLING CORROSION 1-1 PROPELLERS 1-2 LOADING 1-7 HORSEPOWER 1-7 FLOTATION 1-7 BOATING ACCIDENT REPORTS 1-9 2 TUNING 2-1 TUNE-UP
More information9/7/2014 T9.9ELRZ 2001 / TOP COWLING Yamaha Motor Corporation, U.S.A. All rights reserved.
T9.9ELRZ 00 Page of 56 9/7/0 T9.9ELRZ 00 / TOP COWLING 0 Yamaha Motor Corporation, U.S.A. All rights reserved. T9.9ELRZ 00 Page of 56 9/7/0 Part List T9.9ELRZ 00 / TOP COWLING REF - NO PART NUMBER PART
More informationfile://c:\programdata\proquestms\partsmanagerpro\print\ ~13~11~5.html
C60TLRZ 00 file://c:\programdata\proquestms\partsmanagerpro\print\8-9-0 ~~~5.html Page of 6 8/9/0 C60TLRZ 00 / TOP COWLING 0 Yamaha Motor Corporation, U.S.A. All rights reserved. C60TLRZ 00 file://c:\programdata\proquestms\partsmanagerpro\print\8-9-0
More informationOUTBOARD MOTORS FOR PACIFIC ISLAND MARINERS RESTRICTED CLASS 6-MASTER/ENGINEER SPC O22C LEARNER S GUIDE
OUTBOARD MOTORS FOR PACIFIC ISLAND MARINERS RESTRICTED CLASS 6-MASTER/ENGINEER SPC O22C LEARNER S GUIDE SECRETARIAT OF THE PACIFIC COMMUNITY GOVERNMENT OF TAIWAN/ROC TABLE OF CONTENTS TABLE OF CONTENTS
More informationSPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES
TEST AND ADJUSTMENT Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking (Minimum).......................... 28 kpa (4 psi) Oil Pressure.....................................
More informationUnit D: Agricultural Equipment Systems. Lesson 1: Understanding Applications of Fluids and Lubricants in Agricultural Equipment
Unit D: Agricultural Equipment Systems Lesson 1: Understanding Applications of Fluids and Lubricants in Agricultural Equipment 1 Terms Ash content bottom dead center cloud point compression ratio coolant
More informationInternal Combustion Engines
Internal Combustion Engines The internal combustion engine is an engine in which the burning of a fuel occurs in a confined space called a combustion chamber. This exothermic reaction of a fuel with an
More informationIntroduction to I.C Engines CH. 1. Prepared by: Dr. Assim Adaraje
Introduction to I.C Engines CH. 1 Prepared by: Dr. Assim Adaraje 1 An internal combustion engine (ICE) is a heat engine where the combustion of a fuel occurs with an oxidizer (usually air) in a combustion
More information2013 SPRING LAUNCH. (Please Print) Name: Date: Address:
2013 SPRING LAUNCH (Please Print) Name: Date: Address: City: State: Zip: Phone: Home Cell Email: Boat Name: Reg. # Boat Mfg: Model: Year: Length: ft. Beam: ft Number of Engines: 1 2 Inboard Outboard I/O
More informationMARINE.HONDA.COM.AU. BF150 (150hp Outboard)
MARINE.HONDA.COM.AU BF150 (150hp Outboard) The BF150 sets the standard in innovation with its advanced inline fourcylinder technology, placing this engine in a league of its own. INTRODUCTION MAXIMUM POWER
More informationIC ENGINES. Differences between SI and CI engines: Petrol is fuel, which has a high self ignition temperature
IC ENGINES SI Engines work at constant volume. They have a compression ratio of around 6-10. But CI engines work at constant pressure and has a compression ratio of 16-20. In four stroke engines, one power
More informationCalifornia State University, Bakersfield. Signals and Systems. Kristin Koehler. California State University, Bakersfield Lecture 4 July 18 th, 2013
Kristin Koehler California State University, Bakersfield Lecture 4 July 18 th, 2013 1 Outline Internal combustion engines 2 stroke combustion engines 4 stroke combustion engines Diesel engines 2 Consists
More information9/9/2014 F15MSHC 2004 / TOP COWLING Yamaha Motor Corporation, U.S.A. All rights reserved.
F5MSHC 00 Page of 6 9/9/0 F5MSHC 00 / TOP COWLING 0 Yamaha Motor Corporation, U.S.A. All rights reserved. F5MSHC 00 Page of 6 9/9/0 Part List F5MSHC 00 / TOP COWLING REF - NO PART NUMBER PART NAME QUANTITY
More informationGuidance to Instructors on Subject Delivery PISTON ENGINE PROPULSION. This is a suggested programme for the delivery of this subject.
Programme of learning: Guidance to Instructors on Subject Delivery This is a suggested programme for the delivery of this subject. The main headings are the Learning Outcomes (LO1, LO2, etc), with sub
More informationMerCruiser & Mercury Diesel Logbook R02
MerCruiser & Mercury Diesel Logbook 90-889160R02 04/2015 IMPORTANT Maintenance must be completed by a Mercury Marine/Brunswick Marine in EMEA authorized dealer. At the completion of any maintenance check-up
More information9/8/ MSHZ 2001 / TOP COWLING Yamaha Motor Corporation, U.S.A. All rights reserved.
9.9MSHZ 00 Page of 47 9/8/04 9.9MSHZ 00 / TOP COWLING 04 Yamaha Motor Corporation, U.S.A. All rights reserved. 9.9MSHZ 00 Page of 47 9/8/04 Part List 9.9MSHZ 00 / TOP COWLING REF - NO PART NUMBER PART
More informationENGINE & WORKING PRINCIPLES
ENGINE & WORKING PRINCIPLES A heat engine is a machine, which converts heat energy into mechanical energy. The combustion of fuel such as coal, petrol, diesel generates heat. This heat is supplied to a
More informationDownload Service & repair manual Yamaha F250, LF PDF Service Manual
Download Service & repair manual Yamaha F250, LF250 2006 - PDF Service Manual DOWNLOAD HERE "Download Service & repair manual Yamaha F250, LF250 2006 - PDF Service Manual Do you want to service & repair
More informationTABLE OF CONTENTS 3 POWERHEAD
TABLE OF CONTENTS 1 SAFETY POWERHEAD SERVICE -- REDESIGNED MODEL (See Listing on Page) 3-27 1-1 3-27 CLEANING, WAXING, &. POLISHING 1-1 3-32 CONTROLLING CORROSION 1-1 3-66 PROPELLERS 1-2 3-48 FUEL SYSTEM
More information9.7 Replacement of the compressed air distributor
9.6.6 9.6.7 screw in the bolt and to increase unscrew the bolt. For a complete rotation of the bolt, the variation is of 1mm. After measuring the pointer position and the compensatory adjustment screw
More informationThe only outboards in their class to offer EFI, a high-output alternator and smooth-operating 3-cylinder design.
30 HP & 25 HP The only outboards in their class to offer EFI, a high-output alternator and smooth-operating 3-cylinder design. 30HP&25HPFOURSTROKES Water isdrawn into intake grate by the impeller and forced
More informationYamaha F300 Joins the Mechanical Control 4.2-litre Family
BOAT PROPELLER OUTBOARD yamaha-motor.ca NEW F300/F250/F225 MECHANICAL 4.2-Litre V6 Offshore efficiency, light weight and performance now available with mechanical control. When Yamaha launched the 4.2-litre
More informationFORZA BOLT OUTBOARD MOTOR OWNER S MANUAL
FORZA BOLT OUTBOARD MOTOR OWNER S MANUAL Table Of Contents 1.Introduction...1 2.Safety Information.1 3.Refuelling Information...1 4.Safety Matters 2 5.Preparation.3 6.Operation.3 7.Maintenance...4 8.Storage...5
More informationMARINE.HONDA.COM.AU. BF8 (8hp Outboard)
MARINE.HONDA.COM.AU BF8 (8hp Outboard) Reliable and economical power in a lightweight package, the BF8 is built to deliver complete satisfaction when you're on the water. INTRODUCTION FREEDOM ON THE WATER
More informationsmall hp fourstroke outboard 2.5 HP 3.5 HP 4 HP 5 HP 6 HP 8 HP 9.9 HP 9.9 HP BigFoot 9.9 HP Pro Kicker 15 HP 15 HP ProKicker 20 HP
small hp fourstroke outboard 2.5 HP 3.5 HP 4 HP 5 HP 6 HP 8 HP 9.9 HP 9.9 HP BigFoot 9.9 HP Pro Kicker 15 HP 15 HP ProKicker 20 HP 25 HP EFI 30 HP EFI 54 46 55 2.5hp 2.5hp S P E C I F I C A T I O N S K
More informationAir Cooled Engine Technology. Roth 9 th Ch 5 2 & 4 Cycle Engines Pages 81 94
Roth 9 th Ch 5 2 & 4 Cycle Engines Pages 81 94 1. The of the piston is its movement in the cylinder from one end of its travel to another. Either TDC to BDC (downstroke) or BDC to TDC (upstroke). Identified
More informationINDEX INTRODUCTION. Reference No L-01 REVISED:
12-21L-01 1 1 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice. All specifications
More informationEngine, Generators Maintenance & Safety. UAE, Dubai, Cityseason Suites Hotel. Training Course : One Weeks Training Course In. As Under Details :
Training Course : Engine, Generators Maintenance & Safety One Weeks Training Course In UAE, Dubai, Cityseason Suites Hotel As Under Details : Mohammad Issa External Training Coordinator 0096597535000 Tel.
More information26cc 4.5 KWA Marine Engine
26cc 4.5 KWA Marine Engine Thank you for purchasing your new Venom 26cc 4.5 KWA Marine Engine. Not only did you purchase a top of the line R/C Marine Engine but you have also joined the Venom Team and
More informationGLOSSARY. Block. Cylinders
Engine The power source for any farm tractor is the engine. The engine provides the muscle for the power train and the hydraulic system. The typical modern farm tractor has a diesel engine ranging from
More informationLUBRICANTS AND ENGINE CARE PRODUCTS
ENGINE OILS SMOOTH, CLEAN & TROUBLE-FREE Like any precision instrument, your marine engine requires precise care to keep it running at peak performance. If you bought the best, keep it the best. Use only
More informationSINGLE LEVER TOP MOUNT CONTROLS
SINGLE LEVER 20 Single lever / dual action control to operate both throttle and shift. Suitable for any type of boats with outboard, inboard or I/O power plants. SINGLE LEVER Enables easy and safe shifting
More informationSPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES
ENGINE FD620D, K SERIES SPECIFICATIONS SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking
More informationservice bulletin MCM 4.3L, 4.3LX Alpha GM Generation II Engine Specifications No
service bulletin TO: SERVICE MANAGER MECHANICS PARTS MANAGER No. 91-17 MCM 4.3L, 4.3LX Alpha GM Generation II Engine Specifications NOTE: These engines have an electric fuel pump because there is no pad
More informationservice bulletin MCM 350 Magnum Alpha, MCM 5.7L Bravo, MIE 350 Magnum Tournament Ski Inboard Specifications No. 91-8
service bulletin TO: SERVICE MANAGER MECHANICS PARTS MANAGER No. 91-8 MCM 350 Magnum Alpha, MCM 5.7L Bravo, MIE 350 Magnum Tournament Ski Inboard Specifications NOTE: These three engines have a steel camshaft
More informationSINGLE LEVER TOP MOUNT CONTROLS
SINGLE LEVER 20 Single lever / dual action control to operate both throttle and shift. Suitable for any type of boats with outboard, inboard or I/O power plants. SINGLE LEVER Enables easy and safe shifting
More informationUnit C: Agricultural Power Systems. Lesson 1: Understanding Principles of Operation of Internal Combustion Engines
Unit C: Agricultural Power Systems Lesson 1: Understanding Principles of Operation of Internal Combustion Engines 1 Terms Compression Compression stroke Connecting rod Crankshaft Cycle Cylinder Diesel
More informationThe Perfect Solution for Larger Craft with Mechanical Control
YA M A H A M A RINE GROUP HOT SHEET BOAT PROPELLER OUTBOARD F250/F225 Mechanical yamaha-motor.ca NEW EFFECTIVE APRIL 1, 2016 The Perfect Solution for Larger Craft with Mechanical Control 4.2-Litre V6 Offshore
More informationMARINE.HONDA.COM.AU. BF40 (40hp Outboard)
MARINE.HONDA.COM.AU BF40 (40hp Outboard) The most technologically-advanced, lightweight, quietest 4-Stroke 40HP outboard engine the world has ever seen. INTRODUCTION COMPACT INNOVATION Not only is the
More informationService Instruction ENGINE COMPONENTS, INC.
Title: Service Instruction S.I. No.: 89-5-1 Page: 1 of 5 Issued: 05/05/89 Revision: 1 (09/01/01) Technical Portions of FAA DER Approved. FAILURE OF ENGINE TO START 27 points 1. Lack of fuel 2. Ignition
More informationAttached are your Spring Commission and Launch forms.
Dear Valued Customer, Attached are your Spring Commission and Launch forms. Spring is our busiest time of the year and we want to ensure that your boat is ready when you are. Please make sure to fill out
More informationBRIDGESTONE M 1)RCYCLES TUNING UP
BRIDGESTONE M 1)RCYCLES TUNING UP BRIDGESTONE MOTORCYCLES TUNING UP FOR COMPETITION CONTENTS Introduction... 4 Tuning up 350 GTR for Road Racing...,... 7 Tuning up 350 GTR for Scrambling... 10 Tuning up
More informationVentilation System Before Starting
How Long Should You Crank An Engine Ventilation System Before Starting Any electric start motor should be able to be started using a rope, (unless the motor Someone may have "worked' on it before and flopped
More informationIntroducing the Sea-Doo 4-TEC SUPERCHARGED
Introducing the Sea-Doo 4-TEC SUPERCHARGED 185HP & MASSIVE TORQUE iame41-1.doc 29Mar03 Page 1 of 2 Another Sea-Doo watercraft first and only. Introducing the 185hp, GTX 4-TEC SUPERCHARGED PWC. The 4-TEC
More informationFebruary 26, ch.12.notebook. Ch. 12. Preventative Maintenance and Troubleshooting. Feb 23 5:03 PM
Ch. 12 Preventative Maintenance and Troubleshooting Feb 23 5:03 PM 1 Why PM? preventive maintenance certain maintenance tasks must be performed regularly to keep an engine working properly helps premature
More informationMariner 15 Hp Outboard 2 Stroke Manual READ ONLINE
Mariner 15 Hp Outboard 2 Stroke Manual READ ONLINE Mariner Outboard 2 Stroke Forum Topics. Mariner Outboard Parts: Lower Units: Boat Propellers: Mercury & Mariner Outboards: 0: Manual for Mariner 15 hp
More informationF350C NEW. F350C: Yamaha s Flagship Now Offers a Benefit as Big as its Displacement
YA M A H A M A RINE GROUP HOT SHEET BOAT PROPELLER OUTBOARD yamaha-motor.ca NEW EFFECTIVE APRIL 1, 2016 : Yamaha s Flagship Now Offers a Benefit as Big as its Displacement The 5.3-litre V8 outboard, honed
More informationTM T.O. 38G
T.O. 38G1-48-12-2-1 TECHNICAL MANUAL VOLUME 2 OF 2 PART 1 OF 2 MAINTENANCE DIRECT SUPPORT AND GENERAL SUPPORT LEVEL ENGINE ASSEMBLY, DIESEL (MULTIFUEL): NATURALLY ASPIRATED OR TURBOCHARGED, FUEL-INJECTED,
More informationMercury 120 Hp Inboard Service Manual
Mercury 120 Hp Inboard Service Manual If you are searching for the book Mercury 120 hp inboard service manual in pdf format, then you have come on to the correct website. We present the complete version
More information1 GENERAL INFORMATION,
CONTENTS 1 GENERAL INFORMATION, AND BOATING SAFETY HOW TO USE THIS MANUAL 1 2 BOATING SAFETY 1 3 SAFETY IN SERVICE 1-11 TOOLS AND EQUIPMENT 2-2 TOOLS 2-4 FASTENERS, MEASUREMENTS AND CONVERSIONS 2-12 ENGINE
More informationAero Engines. Review Oil & Fuel
Aero Engines 9.02 Oil & Fuel References: FTGU pages 57-61 Review 1. What are the 4 strokes in a complete cycle? 2. Name 3 types of combustion engine. 3. List a few advantages and/or disadvantages to each
More informationEngines. ii. Explain the operation of spark ignition and compression ignition for internal combustion engines used aboard small vessels.
Quartermaster 13b. i. Explain the principal features of steam turbine, turboelectric, direct reversing diesel, dieselelectric, gas turbine, nuclear, gasoline, and diesel engines and the relative advantages
More informationHydra Drive. The HYDRA DRIVE diesel line-up. All the turnkey pleasure and reliability from Yamaha but inside.
Hydra Drive Diesel Hydra Drive The HYDRA DRIVE diesel line-up. All the turnkey pleasure and reliability from Yamaha but inside. Welcome to the world of YAMAHA, where unmatched experience in the manufacture
More informationLecture 5. Abnormal Combustion
Lecture 5 Abnormal Combustion Abnormal Combustion The Abnormal Combustion:- When the combustion gets deviated from the normal behavior resulting loss of performance or damage to the engine. It is happened
More informationSuper 1050 Chain Saw UT Page 1 of 16 Carburetor Chamber
Super 1050 Chain Saw UT-10139 Page 1 of 16 Carburetor Chamber Super 1050 Chain Saw UT-10139 Page 2 of 16 Carburetor Chamber 1 58319A 1 RING- Retaining 2 592301 1 COVER- Air filter 3 A70326 1 NUT- Cover
More informationWINTERIZATION SERVICE MENU
2018 2019 WINTERIZATION SERVICE MENU PLEASE (X) THE DESIRED SELECTION 1. ( ) INBOARD/STERNDRIVE (PER ENGINE)-INCLUDES DRAIN BLOCK AND MANIFOLD REFILL BLOCK W/NON-TOXIC ANTFREEZE -50 BELOW CONNECT REMOTE
More informationSINGLE LEVER TOP MOUNT CONTROLS
SINGLE LEVER TOP MOUNT CONTROLS 20 Single lever / dual action control to operate both throttle and shift. Suitable for any type of boats with outboard, inboard or I/O power plants. SINGLE LEVER TOP MOUNT
More informationIllustrated Parts List AA0101 AA0101. Model Series TABLE OF CONTENTS TYPE NUMBER 0001, 0005, 0020, Blower Housing/Cowl Carburetor...
FORM MS 5131 10/27/2004 REPLACES FORM MS 5131 09/01/2003 AA0101 Illustrated Parts List TABLE OF CONTENTS Model Series AA0101 TYPE NUMBER 0001, 0005, 0020, 0025. Blower Housing/Cowl.....................
More informationThe engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Keep this Owner s Manual handy, so you can refer to
More informationMarine Products. SL-3 Engine Controls. Owner s Manual
Marine Products SL-3 Engine Controls Owner s Manual This manual must be accessible to the owner/user of this Morse marine product. Includes installation, operation and maintenance instructions for your
More informationNew F90 is Strongest 90-hp Outboard Money Can Buy!
BOAT PROPELLER OUTBOARD BOAT PROPELLER OUTBOARD yamaha-motor.ca F 90/F 75 NEW New F90 is Strongest 90-hp Outboard Money Can Buy! The new Yamaha F90 achieves what every next- generation Yamaha outboard
More informationChapter 40: Engines and motors
Chapter 40: Engines and motors Dr. Bassam A. Tayeh Engineering Technical English Islamic University of Gaza April, 2017 Contents A. Types and functions of engines and motors B. Internal combustion engines
More informationRobinson R44. Systems
Robinson R44 Systems The airframe is primarily a metal construction. The primary fuselage is welded steel tubing and riveted aluminium sheet. The tailcone is an aluminium semi-monocoque structure where
More informationUnit C: Agricultural Power Systems. Lesson 5: Using Small Engines
Unit C: Agricultural Power Systems Lesson 5: Using Small Engines Student Learning Objectives: Instruction in this lesson should result in students achieving the following objectives: 1. Identify the reasons
More information00-33A-01 CS-330T, CS-360T 1
00-33A-01 CS-330T, CS-360T 1 0 INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice.
More informationSTERN DRIVE AND INBOARD DRIVE UNITS 133
STERN DRIVE AND INBOARD DRIVE UNITS 133 NOTE Lubricate pivot points of dual tie bar, if installed. MERCRUISER STERN DRIVE (ALPHA ONE EXCEPT GENERATION II) The lubrication tasks described in this section
More informationThe Four Stroke Cycle
1 Induction As the piston travels down the cylinder it draws filtered air at atmospheric pressure and ambient temperature through an air filter and inlet valves into the cylinder. 2 Compression When the
More informationElectric Trolling Motor
Electric Trolling Motor L Series User s Manual Please read and retain this manual before using product REACH RoHS TABLE OF CONTENTS Contents GENERAL INFORMATION 4 SPECIFICATIONS 4 WIRING AND BATTERY RECOMMENDATIONS
More informationTwo Cycle and Four Cycle Engines
Ch. 5 Two Cycle and Four Cycle Engines Feb 20 7:43 AM 1 Stroke of the piston is its movement in the cylinder from one end of its travel to the other Feb 20 7:44 AM 2 Four stroke cycle engine 4 strokes
More information