: DESIGN, CONSTRUCTION AND TESTING OF A PNEUMATIC AUTOMOBILE VEHICLE LIFTER. 2003/15533EM
|
|
- Anthony Hines
- 5 years ago
- Views:
Transcription
1 : DESIGN, CONSTRUCTION AND TESTING OF A PNEUMATIC AUTOMOBILE VEHICLE LIFTER. ALIYU UMARU 2003/15533EM DEPARTMENT OF MECHANICAL ENGINEERING, SCHOOL OF ENGINEERING AND ENGINEERING TECHNOLOGY.MINNA, NIGER STATE.. NOVEMBER, 2008.
2 DESIGN, CONSTRUCTION AND TESTING OF PNEUMATIC AUTOMOBILE VEHICLE LIFTER. ALIYU UMARU 2003/15533EM. PROJECT REPORT SUBMITTED IN PARTIAL LFILMENT OF THE REQUIREMENT FOR THE AWARD F BACHELOR OF ENGINEERING (B. ENG) DEGREE IN CHANICAL ENGINEERING, FEDERAL UNIVERSITY OF TECHNOLOGY, MINNA, NIGER STATE. NOVEMBER,
3 DECLARATION I hereby declare that this project work was absolutely conducted by me, Aliyu Umaru. Under close. supervision of Engr. S.N Mohammed of the mechanical Engineering, Federal University of hnology, Minna, Niger state during 2007/2008 academic session. 2D - ~() - Q.bO g Date III
4 CERTIFICATION This is to certify that this project titled, "Design, Construction and Testing of a Pneumatic omobile Vehicle lifter" was carried out by me Aliyu Umaru. Under close supervision of Engr. S.N. ammed and submitted to the Mechanical Engineering Department, Federal University of hnology,minna, in partial fulfillment, of the requirement for the award of Bachelor of Engineering ng.) degree in Mechanical Engineering ' r. S.N. Mohammed ect Supervisor Date R.H. Khan D. Mech. Engineering Date nal Examiner Date.. t IV
5 DEDICATION This project is dedicated to Almighty Allah for His total guidance through out this degree ramme and his beloved prophet Muhammad (S.A.W). Also to my late father Aliyu Babantada and brother Abubakar Yabagi Aliyu may their soul rest in perfect peace (Ameen). It also dedicated to most wonderful mum in the whole world Hajiya Fatima Aliyu, Brother Muhammad Baba Aliyu and II my loved ones. Thank you all for your moral and financial support. :. v
6 AKNOWLEDGEMENT. Glory is to Almighty Allah for his love, mercy, divine health and protection for making this elude project work and programme a successful one. Firstly, my profound gratitude goes to my dear mother Hajiya Fatimatu Aliyu, brother ham mad Baba Aliyu and the entire members of late Alhaji Aliyu Babantada's family for their yers, moral and financial support from the beginning to ending of this programme. I would also like to appreciate the effort of my able supervisor Emir. S.N. Mohammed he is a er, an unele and also my lecturer for his correction, direction, Brilliant advice and criticism which made this project work a huge success. His contribution to the success of this project will ever ain fresh in my memory. I will be indebted if I can not appreciate the contributions of my lecturers in the department R.H.Khan (H.OD Mechanical Engineering Department), Dr. O.K.Abubakre, Engr. Abdulan Salawu, Engr. Nasiru, Dr. O.J. Abu, Engr. M.B. Ndaliman, Engr. K.C. Bala, Dr. O.V. agwu and others that I may not be able to mention I pray for Allah guidance through all your eavour. Finally, I will use this opportunity to acknowledge my invaluable friends and colleagues for their ern, encouragement and moral support especially Muh'd Umar Chado, Anas Ibrahim Alfa, Aliyu akar, Hauwa A. Shafii, Peter Odume, Yakubu A. Minin, Alori Joseph, Abdullahi Ndaliman, Baba h'd, Prince Will E. Madueke, Maharajah N. Muh'd and all my well wishers. VI
7 ABSTRACT The Pneumatic jack Uack lifter) system for Automobile vehicles provides a quick and safe ns of lifting tyres off the ground for replacement of spare or rotating the tyres on a automobile cle. And also for other mechanical work that may be required to be done under the vehicle. The t lift system consist of a housing (cylinder) through the piston is able to slide freely in it. A ram ed to the piston in the cylinder and the lifting arms are connected to the arm. The piston is to move through the transport of air from the air compressor which passes through the hose into inder. Control valve at the entry and exit make the air perform works as a lift. VII
8 T ABLE OF CONTENT page... 1 page... 11,0' r laration iii page... IV leagerneru VI ct vii e of content viii lature xii of figures xiv tables xv and Objectives... 2 cope and Limitations pter two 'terature Review f of Automobile lifters... 5 Rack and Lever jacks Hydraulic jack Mechanic screw jack , Pneumatic lifter vantages of Pneum atic lifter over other forms of lifter Vlll
9 apter three O. (Methodology) Design Considerations And Calculations Design Consideration Material selecti on Cost effectiveness POitability ,4, Operational Factor Maintenance Operational ManuaL Theoretical Background Effect of Pressure Volume of Air, Mechanical Advantage, Velocity Ratio and Efficiency Stress Analysis in Thick wall cylinder Stress Distribution for Tangential and Radial stresses Axial stress and strain Shear stress in the cylinder Yielding in the cylinder Determination of Wall Thickness of Wall Cylinder... 15,4. Buckling of Column Analysis of critical force Cantilever with a Uni fo rmly Distributed Load Design Calculation Automobile lift capacity Working Pressure Pressure Force in the system Tangential and Radial stress on the Cylinder IX
10 Yielding in the Cylinder S :'Thickness, Area and Volume of the Cylinder Critical load to cause Buckling on the Ram Area, Volume of Ram and Piston Velocity Ratio, Mechanical Advantage and Efficiency 'Bending Moment of the Lifting Arm (Fork) ,...,..., hapter four. O. Material Selection, Constructional Procedure, Result and Discussion and Cost Analysis Material selection ,...,...,...,... "..., Constructional Procedure Cylinder Top and Bottom Cylinder Cover Piston and Ram ,...,...,...,...,...,...,...,., Base Plate Cylinder Support Bracket Arm Support Bracket Arm Bracket Control Flow Valves and Seals Dynamic seals Heise Assemblage Procedure Perfo nllance and Testing Result and Discussion CosfAnalysis Material Cost x
11 7.2. Labour Cost Overhead Cost Ge neral Maintenance Guideline...38 ha pter Five.. Conclusion Recommendation ! P1',"rp1nf'P Xl
DESIGN AND FABRICATION OF A PALM KERNEL CRACKING MACHINE DIKEOCHA NKIRUKA OLIVE EM DEPARTMENT OF MECHANICAL ENGINEERING
DESIGN AND FABRICATION OF A PALM KERNEL CRACKING MACHINE ;. BY DIKEOCHA NKIRUKA OLIVE 2006124481EM DEPARTMENT OF MECHANICAL ENGINEERING SCHOOL OF ENGINEERING AND ENGINEERING TECHNOLOGY FEDERAL UNIVERSITY
More informationEFFECT OF SOME PROCESS VARIABLES ON THE PRODUCTION OF BIODIESEL FROM CASTOR OIL JERRY OGHENEVO EYA WONOWE
]'7757 EFFECT OF SOME PROCESS VARIABLES ON THE PRODUCTION OF BIODIESEL FROM CASTOR OIL BY JERRY OGHENEVO EYA WONOWE 2004/18494EH DEPARTMENT OF CHEMICAL ENGINEERING FEDERAL UNIVERSITY OF TECHNOLOGY MINNA,
More informationDESIGN AND FAllRlCATION OF DUAL OPERATED PALM-FRUIT. DIGESTING lviachine
DESIGN AND FAllRlCATION OF DUAL OPERATED PALM-FRUIT DIGESTING lviachine BY ",., ALADE RIDWAN ADENIYI MA TRIC No. 2005/23545EA I,. DEPARTMENT OF AGRICUL1~ URAL & BIORESOURCES ENGINEERING FEDERAL UNIVERSITY
More informationCKING OF NAPHTHA TO PRODUCE BENZENE, TOLUENE AND XYLENE (BTX)
CKING OF NAPHTHA TO PRODUCE BENZENE, TOLUENE AND XYLENE (BTX) By AFOLAYAN ATINUKE ADEOLA 2006/24163EH DEPARTMENT OF CHEMICAL ENGINEERING, FEDERAL;UNIVE~SITY OF TECHNOLOGY, MINNA, NIGERIA NOVEMBER,.2011
More informationBY ABUBAKAR HUSSAINI SANI MATRICULATION NUMBER: 2005/21984EE
DESIGN OF STREET LIGHT ARRANGEMENT FOR A ROAD OF 5KM USIr~G MERCURY VAPOUR LAMP WITH A MINIMUM ILLUMINANCE OF 15 LUX AT THE CENTRE OF THE ROAD AND 8 LUX AT THE ROAD KERBS. ALSO PROVIDE THE POWER SUPPLY
More informationANALYSIS OF OVERCURRENT PROTECTION RELAY SETTINGS OF A COMMERCIAL BUILDING NURUL SYAQIRAH BINTI MOHD SUFI UNIVERSITI MALAYSIA PAHANG
ANALYSIS OF OVERCURRENT PROTECTION RELAY SETTINGS OF A COMMERCIAL BUILDING NURUL SYAQIRAH BINTI MOHD SUFI UNIVERSITI MALAYSIA PAHANG ANALYSIS OF OVERCURRENT PROTECTION RELAY SETTINGS OF A COMMERCIAL BUILDING
More informationCOMPUTATIONAL ANALYSIS OF TWO DIMENSIONAL FLOWS ON A CONVERTIBLE CAR ROOF ABDULLAH B. MUHAMAD NAWI
COMPUTATIONAL ANALYSIS OF TWO DIMENSIONAL FLOWS ON A CONVERTIBLE CAR ROOF ABDULLAH B. MUHAMAD NAWI Report submitted in partial of the requirements for the award of the degree of Bachelor of Mechanical
More informationCOMPARATIVE STUDIES ON REFINING OF PALM OIL USING NIGERIAN CLAYS
COMPARATIVE STUDIES ON REFINING OF PALM OIL USING NIGERIAN CLAYS SALA WUDEEN TAOFEEK OLALEKAN M.ENG/SEET/20011725 DEPARTMENT OF CHEMICAL ENGINEERING, FEDERAL UNIVERSITY OF TECHNOLOGY, MINNA NIGERIA AUGUST,
More informationDEVELOPMENT OF COMPRESSED AIR POWERED ENGINE SYSTEM BASED ON SUBARU EA71 MODEL CHEN RUI
DEVELOPMENT OF COMPRESSED AIR POWERED ENGINE SYSTEM BASED ON SUBARU EA71 MODEL CHEN RUI A project report submitted in partial fulfillment of the requirements for the award of the degree of Bachelor of
More informationA PROJECT REPORT ON PRODUCTION OF BIODIESEL FROM WASTE VEGETABLE OIL.
A PROJECT REPORT ON PRODUCTION OF BIODIESEL FROM WASTE VEGETABLE OIL. BY AKPOR FREDRICK EKAKABOR 2003/14980EH A PROJECT SUBMITTED TO THE DEPARTMENT OF CHEMICAL ENGINEERING, SCHOOL OF ENGINEERING AND ENGINEERING
More informationEXPERIMENT AND ANALYSIS OF MOTORCYCLE EXHAUST DESIGN ABDUL MUIZ BIN JAAFAR
EXPERIMENT AND ANALYSIS OF MOTORCYCLE EXHAUST DESIGN ABDUL MUIZ BIN JAAFAR Report submitted in partial fulfilment of the requirement for the award of the degree of Bachelor of Mechanical Engineering with
More informationFINAL PROJECT RESEARCH PAPER
FINAL PROJECT COMPARISON ANALYSIS OF ENGINE PERFOMANCE BETWEEN CONVENTIONAL ENGINE (CARBURETOR) SYSTEM AND ELECTRONIC FUEL INJECTION (EFI) ENGINE SYSTEM OF TOYOTA KIJANG SERIES 7K-E RESEARCH PAPER Submitted
More informationOptimal Design and Analysis of Hybrid Energy Systems
Yarmouk University Hijjawi Faculty for Engineering Technology Department of Electrical Power Engineering Optimal Design and Analysis of Hybrid Energy Systems (HES) for Some Study Cases in Jordan A Thesis
More informationSTUDY OF EFFECTS OF FUEL INJECTION PRESSURE ON PERFORMANCE FOR DIESEL ENGINE AHMAD MUIZZ BIN ISHAK
STUDY OF EFFECTS OF FUEL INJECTION PRESSURE ON PERFORMANCE FOR DIESEL ENGINE AHMAD MUIZZ BIN ISHAK Thesis submitted in fulfilment of the requirements for the award of the Bachelor of Mechanical Engineering
More informationCOMPARISON ANALYSIS of MOTORCYCLE PERFORMANCE BETWEEN INTAKE MANIFOLD STANDARD AND INTAKE MANIFOLD RACING ON YAMAHA JUPITER Z 2005
FINAL PROJECT COMPARISON ANALYSIS of MOTORCYCLE PERFORMANCE BETWEEN INTAKE MANIFOLD STANDARD AND INTAKE MANIFOLD RACING ON YAMAHA JUPITER Z 2005 Submitted as a Partial fulfillment of The Requirements for
More informationESTIMATION OF VEHICLE KILOMETERS TRAVELLED IN SRI LANKA. Darshika Anojani Samarakoon Jayasekera
ESTIMATION OF VEHICLE KILOMETERS TRAVELLED IN SRI LANKA Darshika Anojani Samarakoon Jayasekera (108610J) Degree of Master of Engineering in Highway & Traffic Engineering Department of Civil Engineering
More informationEFFECT OF WEIGHT PASSANGER TO STOPPING DISTANCE AND BRAKING PEDAL FORCE OF CBR 250 CC
FINAL PROJECT EFFECT OF WEIGHT PASSANGER TO STOPPING DISTANCE AND BRAKING PEDAL FORCE OF CBR 250 CC RESEARCH PAPER Submitted as a Partial fulfillment of The Requirements for Getting Bachelor Degree of
More informationPRELIMINARY PLANT DESIGN OF CHLOROFORM FROM ACETONE AND BLEACHING POWDER CAPACITY 40,000 TONNES PER YEAR. By : MUHAMMAD FAHMI HAKIM D
PRELIMINARY PLANT DESIGN OF CHLOROFORM FROM ACETONE AND BLEACHING POWDER CAPACITY 40,000 TONNES PER YEAR By : MUHAMMAD FAHMI HAKIM D 500 112 007 Supervisor : 1. Muhammad Mujiburrohman, S.T., M.T., Ph.D
More informationDIRECT TORQUE CONTROL OF A THREE PHASE INDUCTION MOTOR USING HYBRID CONTROLLER. RAJESHWARI JADI (Reg.No: M070105EE)
DIRECT TORQUE CONTROL OF A THREE PHASE INDUCTION MOTOR USING HYBRID CONTROLLER A THESIS Submitted by RAJESHWARI JADI (Reg.No: M070105EE) In partial fulfillment for the award of the Degree of MASTER OF
More informationTHE ANALYSIS OF WING PERFORMANCE FOR RECONNAISSANCE UAV ZULKIFLI BIN YUSOF UNIVERSITI MALAYSIA PAHANG
THE ANALYSIS OF WING PERFORMANCE FOR RECONNAISSANCE UAV ZULKIFLI BIN YUSOF UNIVERSITI MALAYSIA PAHANG The Analysis of Wing Performance for Reconnaissance UAV ZULKIFLI BIN YUSOF Report submitted in partial
More informationPOTENTIALITY OF INTRODUCING ABSORPTION CHILLER SYSTEMS TO IMPROVE THE DIESEL POWER PLANT PERFORMANCE IN SRI LANKA A
POTENTIALITY OF INTRODUCING ABSORPTION CHILLER SYSTEMS TO IMPROVE THE DIESEL POWER PLANT PERFORMANCE IN SRI LANKA MTN Albert Master of Engineering 118351A Department of Mechanical Engineering University
More informationLead Acid Batteries Modeling and Performance Analysis of BESS in Distributed Generation
Murdoch University Faculty of Science & Engineering Lead Acid Batteries Modeling and Performance Analysis of BESS in Distributed Generation Heng Teng Cheng (30471774) Supervisor: Dr. Gregory Crebbin 11/19/2012
More informationPRELIMINARY DESIGN OF PRECIPITATED SILICA PLANT FROM SULPHURIC ACID AND SODIUM SILICATE WITH CAPACITY OF 45,000 TON/ YEAR
PRELIMINARY DESIGN OF PRECIPITATED SILICA PLANT FROM SULPHURIC ACID AND SODIUM SILICATE WITH CAPACITY OF 45,000 TON/ YEAR By: Linda Fatmawati D500112005 Supervisor: Dr. Ir. Ahmad M. Fuadi, MT Kun Harismah
More informationABSTRACT. IMPORT STRATEGY of PT. SADIKUN NIAGAMAS RAYA: A CASE STUDY of FUEL DISPENSER IMPORTATION
ABSTRACT Nova Melinda Alamsyah (01120069293) IMPORT STRATEGY of PT. SADIKUN NIAGAMAS RAYA: A CASE STUDY of FUEL DISPENSER IMPORTATION (xii + 79 Pages : 5 Figures : 2 Table : 5 Appendix) Globalization is
More informationMaster of Engineering
STUDIES OF FAULT CURRENT LIMITERS FOR POWER SYSTEMS PROTECTION A Project Report Submitted in partial fulfilment of the requirements for the Degree of Master of Engineering In INFORMATION AND TELECOMMUNICATION
More informationETHYL ALCOHOL FROM MOLASSES PLANT DESIGN WITH CAPACITY 40,000 TON/YEAR
ETHYL ALCOHOL FROM MOLASSES PLANT DESIGN WITH CAPACITY 40,000 TON/YEAR By: Ambar Tri Wahyuni D500102001 Supervisors: 1. Rois Fatoni, ST, MSc, Ph.D 2. Dr. Ir. Ahmad M. Fuadi CHEMICAL ENGINEERING DEPARTMENT
More informationUNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS TESIS
UNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS TESIS JUDUL: DESIGN IMPROVEMENT FOR POWER WINDOW MECHANISM - SCISSOR TYPE SESI PENGAJIAN: 2009/2010 Saya, BADRUL HISYAM BIN AHMAD (871103-06-5557) mengaku
More informationPREDICTION OF REMAINING USEFUL LIFE OF AN END MILL CUTTER SEOW XIANG YUAN
PREDICTION OF REMAINING USEFUL LIFE OF AN END MILL CUTTER SEOW XIANG YUAN Report submitted in partial fulfillment of the requirements for the award of the degree of Bachelor of Engineering (Hons.) in Manufacturing
More informationThis item is protected by original copyright
THE INVESTIGATION OF HYBRID SYSTEM WITH AC TURBINE GENERATOR AND PHOTOVOLTAIC MOHD HAKIMI BIN WAHAT SCHOOL OF ELECTRICAL SYSTEM ENGINEERING UNIVERSITI MALAYSIA PERLIS 2011 THE INVESTIGATION OF HYBRID SYSTEM
More informationDesign Analysis and Optimization of Disc Brake
Design Analysis and Optimization of Disc Brake Assembly of A 4- Wheeler Race C ar Avijit Singh Gangwar B.E. Automobile Engineer Manipal Institute Of Technology Abstract-A disc brake is a wheel brake which
More informationDESIGN AND DEVELOPMENT OF TREADMILL TO GENERATE ELECTRICITY BY USING MECHANICAL ENERGY
DESIGN AND DEVELOPMENT OF TREADMILL TO GENERATE ELECTRICITY BY USING MECHANICAL ENERGY AMIT GAIKWAD 1, AJAY JADHAV 2, PRASAD DHAGE 3, MR. SOURABH BORCHATE 4 1,2,3B.E. Student, Dr.DYPIEMR, Akurdi, Pune,
More information1. INTRODUCTION 3 2. COST COMPONENTS 17
CONTENTS - i TABLE OF CONTENTS PART I BACKGROUND 1. INTRODUCTION 3 1.1. JUSTIFICATION OF MACHINERY 4 1.2. MANAGERIAL APPROACH 5 1.3. MACHINERY MANAGEMENT 5 1.4. THE MECHANICAL SIDE 6 1.5. AN ECONOMICAL
More informationCOMPARISON OF STANDARD EXHAUST AND RACING EXHAUST ON MACHINE PERFORMANCE
FINAL PROJECT COMPARISON OF STANDARD EXHAUST AND RACING EXHAUST ON MACHINE PERFORMANCE Arranged by: BONDAN SENOAJI PRAKOSA D200102007 MECHANICAL ENGINEERING DEPARTMENT INTERNATIONAL PROGRAM IN AUTOMOTIVE/MOTORCYCLE
More informationSignature of the candidate. The above candidate has carried out research for the Masters Dissertation under my supervision.
DECLARATION I declare that this is my own work and this dissertation does not incorporate without acknowledgement any material previously submitted for a Degree or Diploma in any other University or institute
More informationCopyright is owned by the Author of the thesis. Permission is given for a copy to be downloaded by an individual for the purpose of research and
Copyright is owned by the Author of the thesis. Permission is given for a copy to be downloaded by an individual for the purpose of research and private study only. The thesis may not be reproduced elsewhere
More informationCURRENT CARRYING CAPABILTY OF POLYESTER CARBON COATED FOR ELECTRICAL CONDUCTOR MOHD HAIDIR BIN MANAF UNIVERSITI TEKNOLOGI MALAYSIA
CURRENT CARRYING CAPABILTY OF POLYESTER CARBON COATED FOR ELECTRICAL CONDUCTOR MOHD HAIDIR BIN MANAF UNIVERSITI TEKNOLOGI MALAYSIA CURRENT CARRYING CAPABILTY OF POLYESTER CARBON COATED FOR ELECTRICAL CONDUCTOR
More informationOPTIMAL ANTI LOCK BRAKING SYSTEM WITH REGENERATIVE BRAKING IN HYBRID ELECTRIC VEHICLE DANA DEHGHANI UNIVERSITI TEKNOLOGI MALAYSIA
i OPTIMAL ANTI LOCK BRAKING SYSTEM WITH REGENERATIVE BRAKING IN HYBRID ELECTRIC VEHICLE DANA DEHGHANI UNIVERSITI TEKNOLOGI MALAYSIA 1 OPTIMAL ANTI LOCK BRAKING SYSTEM WITH REGENERATIVE BRAKING IN HYBRID
More informationPRELIMINARY DESIGN OF PRECIPITATED SILICA PLANT FROM SULPHURIC ACID AND SODIUM SILICATE WITH CAPACITY OF 40,000 TON/YEARS
PRELIMINARY DESIGN OF PRECIPITATED SILICA PLANT FROM SULPHURIC ACID AND SODIUM SILICATE WITH CAPACITY OF 40,000 TON/YEARS By: MR.ISMAAE YUSOH D500112010 Supervisor: Dr. Ir. Ahmad M. Fuadi, MT Kun Harismah
More informationROBUST ELECTRONIC BRAKE FORCE DISTRIBUTION IN HYBRID ELECTRIC VEHICLES YEOH WEI CHERNG UNIVERSITI TEKNOLOGI MALAYSIA
i ROBUST ELECTRONIC BRAKE FORCE DISTRIBUTION IN HYBRID ELECTRIC VEHICLES YEOH WEI CHERNG UNIVERSITI TEKNOLOGI MALAYSIA 1 ROBUST ELECTRONIC BRAKE FORCE DISTRIBUTION IN HYBRID ELECTRIC VEHICLES YEOH WEI
More informationMODELING OF ELECTRIC DOUBLE LAYER CAPACITOR FATHIN ASILA BINTI MOHD PABLI UNIVERSITI TEKNOLOGI MALAYSIA
MODELING OF ELECTRIC DOUBLE LAYER CAPACITOR FATHIN ASILA BINTI MOHD PABLI UNIVERSITI TEKNOLOGI MALAYSIA MODELING OF ELECTRIC DOUBLE LAYER CAPACITOR FATHIN ASILA BINTI MOHD PABLI A project report submitted
More informationTHE STUDY ON THE IMPACT OF CONSTANT POWER LOAD TO A DIRECT CURRENT POWER SYSTEM DRIVEN BY PHOTOVOLTAIC, WIND - THYRISTOR RECTIFIER AND LINEAR SOURCES
THE STUDY ON THE IMPACT OF CONSTANT POWER LOAD TO A DIRECT CURRENT POWER SYSTEM DRIVEN BY PHOTOVOLTAIC, WIND - THYRISTOR RECTIFIER AND LINEAR SOURCES MOHD JUNDULLAH B. HALIM A project report submitted
More informationRC COMPANY PROFILE
RC1357280 COMPANY PROFILE Contact us: solarbotenergy@gmail.com 08077759100, 07030723850, 08052142581 Visit: www.solarbotenergy.com SOLARBOT PROPOSAL FOR SERVICES For prospective clients OVERVIEW We are
More informationUNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS TESIS
UNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS TESIS JUDUL: DESIGN AND FABRICATE AL-QURAN AND BOOK RACK FOR UMP MOSQUE Saya, AMIR YUSRI MOHD YUSOF SESI PENGAJIAN: 2009/2010 mengaku membenarkan tesis
More informationTHE ANALYSIS OF THE FORCES THAT ACT ON THE MOTORCYCLE BRAKE PEDAL DURING EMERGENCY BRAKE
THE ANALYSIS OF THE FORCES THAT ACT ON THE MOTORCYCLE BRAKE PEDAL DURING EMERGENCY BRAKE SUTHAN A/L ERIN UNIVERSITI TEKNIKAL MALAYSIA MELAKA THE ANALYSIS OF THE FORCES THAT ACT ON THE MOTORCYCLE BRAKE
More informationSavitribai Phule Pune University, Pune, India.
Automation of Mechanisms in B-Test Fixture for Process Cycle Time Improvement Jagdish Kattimani 1, Dnyaneshwar Kedar 2, Vikramaditya Patil 3, Mukesh Chhanwal 4, Nitin Gupte 5 # Department of Mechanical
More informationDEVELOPMENT OF ELECTRICAL DISCHARGE MACHINING POWER GENERATOR MUHD ABU BAKAR BIN MUHD RADZI
i DEVELOPMENT OF ELECTRICAL DISCHARGE MACHINING POWER GENERATOR MUHD ABU BAKAR BIN MUHD RADZI A project report submitted in partial fulfilment of the requirements for the award of the degree of Master
More informationIJESMR. [Jangam*, 4(2): February, 2017] ISSN Impact Factor: Keywords: Chain and Sprocket Mechanism, Limit switches, Plastic
AUTOMATIC CHALKBOARD CLEANER AND DUSTER CLEANER Jangam Rushikesh M. *1, Tamboli Mahesh K. 2 Shelar Pratik C. 3 & Jadhav Harshada K. 4 * 1,2,3&4 Students at Mechanical Department, Jaihind Polytechnic Kuran,
More informationDesign and Analysis of Active Electro Hydraulic Thruster Brake for Lifting Machine
ISSN 2395-1621 Design and Analysis of Active Electro Hydraulic Thruster Brake for Lifting Machine #1 V.S. Kshirsagar, #2 V.H.Waghmare 1 vishalkshirsagar88@gmail.com 2 veeru.w@gmail.com #12 Mechanical Engineering,
More informationGLYCERINE PITCH FROM GLYCERINE CONCENTRATION PROCESS AS ALTERNATIVE FUEL FOR BOILER OPERATIONS KIRUBAHARAN A/L MERAPAN
3 GLYCERINE PITCH FROM GLYCERINE CONCENTRATION PROCESS AS ALTERNATIVE FUEL FOR BOILER OPERATIONS KIRUBAHARAN A/L MERAPAN A project report submitted in partial fulfilment of the requirement for theaward
More informationCONVERSION OF GLYCEROL TO METHANOL OVER COPPER AND NICKEL SUPPORTED ON HZSM-5 ZEOLITE BY HYDROTHERMAL PROCESS NURUL SYUHADA BT SPALIE
CONVERSION OF GLYCEROL TO METHANOL OVER COPPER AND NICKEL SUPPORTED ON HZSM-5 ZEOLITE BY HYDROTHERMAL PROCESS NURUL SYUHADA BT SPALIE A dissertation submitted in fulfillment of the requirements for the
More informationDEVELOPMENT OF A FOOT OPERATED HYDRAULIC LIFTER FOR AUTOMOBILE WORKSHOPS
DEVELOPMENT OF A FOOT OPERATED HYDRAULIC LIFTER FOR AUTOMOBILE WORKSHOPS Ikechukwu Celestine Ugwuoke, Olawale James Okegbile and Ibukun Blessing Ikechukwu Department of Mechanical Engineering, Federal
More informationDesign, Analysis & Balancing of 5 Cylinder Engine Crankshaft
International OPEN ACCESS Journal Of Modern Engineering Research (IJMER) Design, Analysis & Balancing of 5 Cylinder Engine Crankshaft Yogesh S. Khaladkar 1, Lalit H. Dorik 2, Gaurav M. Mahajan 3, Anil
More informationDESIGN AND ANALYSIS OF THE SOLAR CAR BODY YUSRI BIN YUSOF. Report submitted in partial fulfillment of the requirements
DESIGN AND ANALYSIS OF THE SOLAR CAR BODY YUSRI BIN YUSOF Report submitted in partial fulfillment of the requirements for the award of Diploma in Mechanical Engineering Faculty of Mechanical Engineering
More informationFABRICATION OF A PROTOTYPE LOW POWER MOTOR FOR INDOOR VENTILATION SIMON THEOPHYLUS YUSUF
FABRICATION OF A PROTOTYPE LOW POWER MOTOR FOR INDOOR VENTILATION SIMON THEOPHYLUS YUSUF A thesis submitted in fulfilment of the requirements for the award of the degree of Master of Engineering (Electrical)
More informationRedesign of Drive Shaft`s tripod Assembly, to improve the performance & reduce failure
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X, Volume 11, Issue 2 Ver. IV (Mar- Apr. 2014), PP 81-87 Redesign of Drive Shaft`s tripod Assembly, to improve
More informationDISC BRAKE SQUEAL GENERATION DURING DRY AND WET CONDITIONS MUNEER NAJI WAHEED UNIVERSITI TEKNOLOGI MALAYSIA
DISC BRAKE SQUEAL GENERATION DURING DRY AND WET CONDITIONS MUNEER NAJI WAHEED UNIVERSITI TEKNOLOGI MALAYSIA DISC BRAKE SQUEAL GENERATION DURING DRY AND WET CONDITIONS MUNEER NAJI WAHEED A project report
More informationPowering, Load Distribution & Braking of a Dump Truck Kamasani Bujji Babu Assistant Manager Department of Research & Development
IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 09, 2015 ISSN (online): 2321-0613 Powering, Load Distribution & Braking of a Dump Truck Kamasani Bujji Babu Assistant Manager
More informationNUMERICAL ANALYSIS OF ELASTOHYDRODYNAMIC LUBRICATION WITH BIO-BASED FLUIDS DEDI ROSA PUTRA CUPU UNIVERSITI TEKNOLOGI MALAYSIA
NUMERICAL ANALYSIS OF ELASTOHYDRODYNAMIC LUBRICATION WITH BIO-BASED FLUIDS DEDI ROSA PUTRA CUPU UNIVERSITI TEKNOLOGI MALAYSIA NUMERICAL ANALYSIS OF ELASTOHYDRODYNAMIC LUBRICATION WITH BIO-BASED FLUIDS
More informationRESEARCH REPORT PRODUCTION OF BIODIESEL FROM CHICKEN FAT WITH COMBINATION SUBCRITICAL METHANOL AND WATER PROCESS
RESEARCH REPORT PRODUCTION OF BIODIESEL FROM CHICKEN FAT WITH COMBINATION SUBCRITICAL METHANOL AND WATER PROCESS Submitted by: Felix Harijaya Santosa NRP. 5203014015 Ryan Sumule NRP. 5203014037 DEPARTMENT
More informationCONTROL OF INVERTED PENDULUM-CART SYSTEM BASED ON FUZZY LOGIC APPROACH HASRULNIZAM BIN HASHIM
CONTROL OF INVERTED PENDULUM-CART SYSTEM BASED ON FUZZY LOGIC APPROACH HASRULNIZAM BIN HASHIM A project report submitted in partial fulfillment of the requirements for the award of the degree of Master
More informationFABRICATION OF AUTOMATIC HYDRAULIC BENDING AND BEND REMOVING MACHINE
FABRICATION OF AUTOMATIC HYDRAULIC BENDING AND BEND REMOVING MACHINE Mr. Harshad Khairkar 1, Mr. Dhananjay Kopre 2, Mr. Saurabh Kalkar 3, Ms. Dipali Kambe 4, Prof. Sarang Gulhane 5 1Final Year Student,
More informationDesign of Automated Outriggers for Self- Propelled Hydraulic Scissor Lift - A Case Study At Air India
Design of Automated Outriggers for Self- Propelled Hydraulic Scissor Lift - A Case Study At Air India Dileep Kanojia 1 Shubhankar Gokhale 3 Chinmay Rohekar 2 Sanjay Bokade 4 Department Of Mechanical Engineering,
More informationINSTRUCTIONS FOR CONTINUED AIRWORTHINESS FAA-STC SE8987SW. Proposal to Increase Lycoming O-320-E2A Engine Power Rating from 150 hp to 160 hp
INSTRUCTIONS FOR CONTINUED AIRWORTHINESS FAA-STC SE8987SW Proposal to Increase Lycoming O-320-E2A Engine Power Rating from 150 hp to 160 hp Drawing 2663 Notice This document must be referenced on Block
More informationSOLAR GRASS CUTTER VPMP POLYTECHNIC GANDHNAGAR
2017-18 SOLAR GRASS CUTTER VPMP POLYTECHNIC GANDHNAGAR CERTIFICATE V.P.M.P. Polytechnic, Sector-15 Gandhinagar Date: This is to certify that dissertation entailed Solar Grass Cutter has been carried out
More informationENERGY BALANCE STUDY FOR 4 STROKE GASOLINE ENGINE ANALYSES ABDULLAH SHARIFFUDIN MOHAMAD BACHELOR OF MECHANICAL ENGINEERING UNIVERSITI MALAYSIA PAHANG
ENERGY BALANCE STUDY FOR 4 STROKE GASOLINE ENGINE ANALYSES ABDULLAH SHARIFFUDIN MOHAMAD BACHELOR OF MECHANICAL ENGINEERING UNIVERSITI MALAYSIA PAHANG UNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS
More informationMODELING AND SIMULATION OF A HYBRID ELECTRIC VEHICLE SYSTEM
MODELING AND SIMULATION OF A HYBRID ELECTRIC VEHICLE SYSTEM by Eng. Hala Shaban Mohamed Khalil Electronics Research Institute A Thesis Submitted To The Faculty of Engineering at Cairo University In Partial
More informationIncrease Factor of Safety of Go-Kart Chassis during Front Impact Analysis
IJIRST International Journal for Innovative Research in Science & Technology Volume 3 Issue 04 September 2016 ISSN (online): 2349-6010 Increase Factor of Safety of Go-Kart Chassis during Front Impact Analysis
More informationFINITE ELEMENT ANALYSIS OF AUTOMOTIVE INTAKE MANIFOLD USING CAE SOFTWARE MUHAMMAD HAIKAL BIN HARON
FINITE ELEMENT ANALYSIS OF AUTOMOTIVE INTAKE MANIFOLD USING CAE SOFTWARE MUHAMMAD HAIKAL BIN HARON A report submitted in partial fulfilment of the requirements for the award of the degree of Bachelor of
More informationModal analysis of Truck Chassis Frame IJSER
Modal analysis of Truck Chassis Frame 158 Shubham Bhise 1, Vaibhav Dabhade 1, Sujit Pagi 1, Apurvi Veldandi 1. 1 B.E. Student, Dept. of Automobile Engineering, Saraswati College of Engineering, Navi Mumbai,
More informationResearch Article Volume 6 Issue No. 6
DOI 10.4010/2016.1566 ISSN 2321 3361 2016 IJESC Research Article Volume 6 Issue No. 6 Mechanism for Insertion of Tube Bundle in a Shell & Tube Heat Exchanger Ganesh E. Kondhalkar 1, T.K Chengalrayan 2,
More informationStructural Analysis of Student Formula Race Car Chassis
Structural Analysis of Student Formula Race Car Chassis Arindam Ghosh 1, Rishika Saha 2, Sourav Dhali 3, Adrija Das 4, Prasid Biswas 5, Alok Kumar Dubey 6 1Assistant Professor, Dept. of Mechanical Engineering,
More informationDESIGN AND FABRICATION OF ENGINE MOUNTING FOR UTeM FORMULA SYLE RACE CAR MOHD SABIRIN BIN RAHMAT UNIVERSITI TEKNIKAL MALAYSIA MELAKA
DESIGN AND FABRICATION OF ENGINE MOUNTING FOR UTeM FORMULA SYLE RACE CAR MOHD SABIRIN BIN RAHMAT UNIVERSITI TEKNIKAL MALAYSIA MELAKA DESIGN AND FABRICATION OF ENGINE MOUNTING FOR UTeM FORMULA STYLE RACE
More informationCOMPARISON OF AUTOMATIC AND CVT TRANSMISSION FOR A CAR UNDER 1 LITER ENGINE
COMPARISON OF AUTOMATIC AND CVT TRANSMISSION FOR A CAR UNDER 1 LITER ENGINE AHMAD MUSTAKIM BIN MOHD RUSLI BACHELOR OF ENGINEERING UNIVERSITI MALAYSIA PAHANG 2010 UNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN
More informationDesign, Construction and Testing of an Electric Powered Toggle Jack Mechanism
Design, Construction and Testing of an Electric Powered Toggle Jack Mechanism Ipilakyaa T.D. 1, Achirgbenda V.T. 2, Gbashi S. 3 1Department of Mechanical Engineering, University of Agriculture Makurdi,
More informationPRACTICAL TROUBLESHOOTING OF ELECTRICAL EQUIPMENT & CONTROL SYSTEMS
Training Title PRACTICAL TROUBLESHOOTING OF ELECTRICAL EQUIPMENT & CONTROL SYSTEMS Training Duration 5 days Training Venue and Dates Practical Troubleshooting Of Electrical Equipment & Control Systems
More informationTo provide exceptional aircraft turbine engine services through our commitment to quality and safety while exceeding our customers expectations.
24 The AutoPILOT Southeast 2009 Southeast Turbines Southeast Turbines To provide exceptional aircraft turbine engine services through our commitment to quality and safety while exceeding our customers
More informationRESEARCH PROJECT REPORT
RESEARCH PROJECT REPORT MODELING OF LIQUID FUEL PRODUCTION VIA CATALYTIC CRACKING OF PALM OIL USING MCM-41 AS CATALYST PROPOSED BY: HENGKY KURNIAWAN IVAN YARED 5203004011 5203004023 DEPARTMENT OF CHEMICAL
More informationHarmonic Analysis of Reciprocating Compressor Crankcase Assembly
IOSR Journal of Engineering (IOSRJEN) www.iosrjen.org ISSN (e): 2250-3021, ISSN (p): 2278-8719 PP 16-20 Harmonic Analysis of Reciprocating Compressor Crankcase Assembly A. A. Dagwar 1, U. S. Chavan 1,
More informationLoad Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4 Stroke Engine
IJSRD - International Journal for Scientific Research & Development Vol. 3, Issue 08, 2015 ISSN (online): 2321-0613 Load Analysis and Multi Body Dynamics Analysis of Connecting Rod in Single Cylinder 4
More informationDesign and Development of Gearbox Tester
International Research Journal of Engineering and Technology (IRJET) e-issn: 395-5 Design and Development of Gearbox Tester Vandan Bari 1, Akshay Sawant, Jayesh Parmar 3, Pradeep Sharma, Vaibhav Lande
More informationDesign and Stress Analysis of Crankshaft for Single Cylinder 4-Stroke Diesel Engine
Design and Stress Analysis of Crankshaft for Single Cylinder 4-Stroke Diesel Engine Amit Solanki #1, Jaydeepsinh Dodiya #2, # Mechanical Engg.Deptt, C.U.Shah University, Wadhwan city, Gujarat, INDIA Abstract
More informationAPPLICATION OF DEMAND SIDE MANAGEMENT STRATEGIES TO REDUCE ENERGY CONSUMPTION IN UNIVERSITY BUILDINGS NAJAATUL FARIHAH BINTI HAMIDI
iii APPLICATION OF DEMAND SIDE MANAGEMENT STRATEGIES TO REDUCE ENERGY CONSUMPTION IN UNIVERSITY BUILDINGS NAJAATUL FARIHAH BINTI HAMIDI A thesis submitted in fulfilment of the requirements for the award
More informationDESIGN, DETAIL ANALYSIS AND PERFORMANCE TESTING OF UAV PROPULSION SYSTEM CHE MUHAMMAD RIDHWAN BIN CHE HASHIM
DESIGN, DETAIL ANALYSIS AND PERFORMANCE TESTING OF UAV PROPULSION SYSTEM CHE MUHAMMAD RIDHWAN BIN CHE HASHIM Faculty of Mechanical Engineering UNIVERSITI MALAYSIA PAHANG UNIVERSITI MALAYSIA PAHANG BORANG
More informationResearch Report. C. Kiriklidis and G. Dounias
Research Report 1082 Benchmark Problems related to Resource Leveling Optimization: Best solutions obtained from the Application of different Evolutionary Intelligence Algorithms C. Kiriklidis and G. Dounias
More informationAbu Dhabi Department of Transport Application Form Non Objection Certificate (NOC)
Abu Dhabi Department of Transport Application Form Non Objection Certificate (NOC) for a Commercial Licence to Operate Goods Vehicles with an Unladen Weight of over 2.5 tonnes Does this Application Apply
More informationLine of Paint Industry
Result Analysis of Energy Saving in Filling Line of Paint Industry Sushant Pawar 1, Dr.Lavendra Bothra M. E, Department of Energy System &Management, ARMIET, Sapgaon, India Chairman, Department of Energy
More informationPerformance Testing Of Torque Limiter Timer Belt Spindle Drive for Overload Protection
American Journal of Engineering Research (AJER) e-issn: 2320-0847 p-issn : 2320-0936 Volume-4, Issue-7, pp-276-289 www.ajer.org Research Paper Open Access Performance Testing Of Torque Limiter Timer Belt
More informationFundamentals of Engineering High-Performance Actuator Systems. Kenneth W. Hummel
Fundamentals of Engineering High-Performance Actuator Systems Kenneth W. Hummel Author Name Chapter 1: Introduction...1 1.1 Fundamentals... 2 1.2 Performance... 2 1.3 Loads... 3 1.4 Constraints... 3 1.5
More informationDEVELOPMENT HYDROGEN GAS GENERATOR FOR DUAL FUEL ENGINE USING YULL BROWN METHOD AHMAD ZAKI BIN ZAIMANI UNIVERSITI MALAYSIA PAHANG
DEVELOPMENT HYDROGEN GAS GENERATOR FOR DUAL FUEL ENGINE USING YULL BROWN METHOD AHMAD ZAKI BIN ZAIMANI UNIVERSITI MALAYSIA PAHANG ii UNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS TESIS JUDUL: DEVELOPMENT
More informationAddressing the API Licensing Fear Factor
Addressing the API Licensing Fear Factor Overview There are motor oil consumers who have a fear of using non-api certified motor oils, i.e. motor oils that do not have the API donut certification. The
More informationPublic Works Operations Manual Standard Operating Procedures for Water and Sewer WS - B311 Sanitary Sewer Connection Repair
Public Works Operations Manual Standard Operating Procedures for Water and Sewer WS - B311 Sanitary Sewer Connection Repair 1. Objective: 1.1. To repair the sanitary sewer connection in a timely and efficient
More informationHigher National Unit Specification. General information for centres. Electrical Motor Drive Systems. Unit code: DN4K 35
Higher National Unit Specification General information for centres Unit code: DN4K 35 Unit purpose: This Unit has been designed to allow candidates to develop a knowledge and understanding of electrical
More informationTHE DESIGN OF A TORQUE FEEDBACK CONTROLLER USING PID CONTROLLER FOR AN UPPER LIMB ROBOTIC ARM KARTIKESU A/L VIJAYAN
THE DESIGN OF A TORQUE FEEDBACK CONTROLLER USING PID CONTROLLER FOR AN UPPER LIMB ROBOTIC ARM KARTIKESU A/L VIJAYAN A report submitted in partial fulfillment of the requirements for the degree of Bachelor
More informationDESIGN AND DEVELOPMENT OF INTEGRATED PNEUMATIC CAR JACK
DESIGN AND DEVELOPMENT OF INTEGRATED PNEUMATIC CAR JACK Kaushal H. Pandya 1, Amit V. Sawant 2, Vinayak S. Gurav 3, Assistant Prof. S S Gurav 4 1,2,3,4 Mechanical Department, Nanasaheb Mahadik college of
More informationPort of Long Beach. Diesel Emission Reduction Program
Diesel Emission Reduction Program Competition Port of Long Beach, Planning Division July 16, 2004 Contact: Thomas Jelenić, Environmental Specialist 925 Harbor Plaza, Long Beach, CA 90802 (562) 590-4160
More informationTrouble Shooting in Vertical Fire Hydrant Pump by Vibration Analysis - A Case Study
Trouble Shooting in Vertical Fire Hydrant Pump by Vibration Analysis - A Case Study V. G. Arajpure & H. G. Patil Department of Mechanical Engineering, BDCOE Sewagram, Dist:-Wardha, Maharashtra 442001,
More informationTHE GENERAL ASSEMBLY OF PENNSYLVANIA SENATE BILL REFERRED TO ENVIRONMENTAL RESOURCES AND ENERGY, FEBRUARY 6, 2017 AN ACT
PRINTER'S NO. THE GENERAL ASSEMBLY OF PENNSYLVANIA SENATE BILL No. 1 Session of 01 INTRODUCED BY LEACH AND HAYWOOD, FEBRUARY, 01 REFERRED TO ENVIRONMENTAL RESOURCES AND ENERGY, FEBRUARY, 01 AN ACT 1 1
More informationMISSION VALLEY REGIONAL OCCUPATIONAL PROGRAM TRANSPORTATION SECTOR BASIC CAR CARE COURSE OUTLINE
MISSION VALLEY REGIONAL OCCUPATIONAL PROGRAM TRANSPORTATION SECTOR BASIC CAR CARE COURSE OUTLINE 1. Course Title: Basic Car Care 2. CBEDS Title: Automotive Mechanics 3. CBEDS Number: 5655 4. Job Titles/DOT
More informationUNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS TESIS
UNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS TESIS JUDUL: DESIGN AND DEVELOPMENT OF 1-SEATED URBAN CAR CHASSIS USING ALUMINIUM SESI PENGAJIAN: 2010/2011 Saya, FAZLIANA BINTI FAUZUN (880216-01-5438)
More informationDiagnostics of Rotor and Stator Problems in Industrial Induction Motors
Diagnostics of Rotor and Stator Problems in Industrial Induction Motors by Fang Duan B.E. (Telecommunication Engineering), Southwest Jiaotong University, China, 2005 Thesis submitted for the degree of
More information